HomeMy WebLinkAboutPermit D08-044 - GE - OFFICEGE
12600 INTERURBAN AV S
DOS -044
Parcel No.: 0004800003
Address: 12600 INTERURBAN AV S TUKW
Suite No:
Tenant:
Name: GE
Address: 12600 INTERURBAN AV S , TUKVVILA WA
Owner:
Name: C/O EPROPERTYTAX INC
Address: DEPT #207 , PO BOX 4900 85261
Phone:
Contact Person:
Name: DAVID KEHLE
Address: 1916 BONAIR DR SW , SEATTLE WA 98168
Phone: 206 - 433 -8997
Contractor:
Name: PRECISION BUILDERS INC
Address: PO BOX 98609 , DES MOINES WA 98198 -0609
Phone: 206 878 -2948
Contractor License No: PRECIBI151C2
doc: IBC -10/06
CitAbf Tukwila •
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206-431-3670
Fax: 206- 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
DEVELOPMENT PERMIT
Permit Number: D08 - 044
Issue Date: 02/19/2008
Permit Expires On: 08/17/2008
Value of Construction: $7,500.00 Fees Collected: $328.73
Type of Fire Protection: SPRINKLERS International Building Code Edition: 2006
Type of Construction: V -B Occupancy per IBC: 0008
DESCRIPTION OF WORK:
CONSTRUCT NEW OFFICE FOR TENANT TO INCLUDE NON - BEARING WALLS AND SUSPENDED ACOUSTICAL CEILING
* * continued on next page **
Expiration Date: 01/19/2010
D08 -044 Printed: 02 -19 -2008
Public Works Activities:
Channelization / Striping: N
Curb Cut / Access / Sidewalk / CSS: N
City STukwila •
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206-431-3670
Fax: 206 - 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
Permit Number: DO8 - 044
Issue Date: 02/19/2008
Permit Expires On: 08/17/2008
Fire Loop Hydrant: N Number: 0 Size (Inches): 0
Flood Control Zone:
Hauling: N Start Time: End Time:
Land Altering: Volumes: Cut 0 c.y. Fill 0 c.y.
Landscape Irrigation:
Moving Oversize Load: Start Time: End Time:
Sanitary Side Sewer:
Sewer Main Extension: Private: Public:
Storm Drainage:
Street Use: Profit: N Non - Profit: N
Water Main Extension: Private: Public:
Water Meter: N
Permit Center Authorized Signature:
I hereby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances
governing this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating
construction or th rformancewfirk. I am authorized to sign and obtain this development permit.
Signature:
doc: IBC -10/06
WI? Date: u
Date: - GCS
Print Name: f et)
This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended
or abandoned for a period of 180 days from the last inspection.
D08 -044 Printed: 02 -19 -2008
Parcel No.: 0004800003
Address: 12600 INTERURBAN AV S TUKW
Suite No:
Tenant: GE
1: ** *BUILDING DEPARTMENT CONDITIONS * **
•
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206- 431 -3665
Web site: http://www.ci.tukwila.wa.us
PERMIT CONDITIONS
Permit Number: D08 -044
Status: ISSUED
Applied Date: 01/29/2008
Issue Date: 02/19/2008
2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the
Building Official.
3: All mechanical work shall be inspected and approved under a separate permit issued by the City of Tukwila Permit Center
(206/431- 3670).
4: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to
start of any construction. These documents shall be maintained and made available until final inspection approval is
granted.
5: New suspended ceiling grid and light fixture installations shall meet the non - building structures seismic design
requirements of ASCE 7.
6: All construction shall be done in conformance with the approved plans and the requirements of the International
Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code.
7: Remove all demolition rubble and loose miscellaneous material from lot or parcel of ground, properly cap the sanitary
sewer connections, and properly fill or otherwise protect all basements, cellars, septic tanks, wells, and other
excavations. Final inspection approval will be determined by the building inspector based on satisfactory completion of
this requirement.
8: All rack storage requires a separate permit issued through the City of Tukwila Permit Center. Rack storage over 8 -feet
in height shall be anchored or braced to prevent overturning or displacement during seismic events. The design and
calculations for the anchorage or bracing shall be prepared by a registered professional engineer licensed in the State
of Washington.
9: Ventilation is required for all new rooms and spaces of new or existing buildings and shall be in conformance with the
International Building Code and the Washington State Ventilation and Indoor Air Quality Code.
10: All plumbing and gas piping work shall be inspected and approved under a separate permit issued by the Cityof Tukwila
Permit Center.
11: All electrical work shall be inspected and approved under a separate permit issued by the City of Tukwila Building
Department (206- 431 - 3670).
12: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of,
any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits
presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila
shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the
Building Official from requiring the correction of errors in the construction documents and other data.
13: ** *FIRE DEPARTMENT CONDITIONS * **
14: The attached set of building plans have been reviewed by the Fire Prevention Bureau and are acceptable with the
doc: Cond -10/06
D08 -044 Printed: 02 -19 -2008
following concerns:
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 - 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
15: Maintain coverage and operability of portable fire extinguishers, sprinkler systems and fire alarm systems during
demolition and construction.
16: The total number of fire extinguishers required for a light hazard occupancy with Class A fire hazards is calculated at
one extinguisher for each 3,000 sq. ft. of area. The extinguisher(s) should be of the "all purpose" (2A, 10 B:C) dry
chemical type. The travel distance to any extinguisher must be 75' or less. (IFC 906.3) (NFPA 10, 3 -2.1)
17: Portable fire extinguishers, not housed in cabinets, shall be installed on the hangers or brackets supplied. Hangers or
brackets shall be securely anchored to the mounting surface in accordance with the manufacturer's installation
instructions. Portable fire extinguishers having a gross weight not exceeding 40 pounds (18 kg) shall be installed so
that its top is not more than 5 feet (1524 mm) above the floor. Hand -held portable fire extinguishers having a gross
weight exceeding 40 pounds (18 kg) shall be installed so that its top is not more than 3.5 feet (1067 mm) above the
floor. The clearance between the floor and the bottom of the installed hand -held extinguishers shall not be less than 4
inches (102 mm). (IFC 906.7 and IFC 906.9)
18: Fire extinguishers shall not be obstructed or obscured from view. In rooms or areas in which visual obstruction cannot
be completely avoided, means shall be provided to indicate the locations of the extinguishers. (IFC 906.6)
19: Extinguishers shall be located in conspicuous locations where they will be readily accessible and immediately available
for use. These locations shall be along normal paths of travel, unless the fire code official determines that the
hazard posed indicates the need for placement away from normal paths of travel. (IFC 906.5)
20: No point in a building may exceed the maximum exit access travel distance listed in Chapter 10, section 1015, Table
1015.1 of the International Fire Code and International Building Code.
21: Egress doors shall be readily openable from the egress side without the use of a key or special knowledge or effort.
(IFC 1008.1.8.3 subsection 2.2)
22: Door handles, pulls, latches, locks and other operating devices on doors required to be accessible by Chapter 11 of the
International Building Code shall not require tight grasping, tight pinching or twisting of the wrist to operate. (IFC
1008.1.8.1)
23: Maintain sprinkler coverage per N.F.P.A. 13. Addition/relocation of walls, closets or partitions may require relocating
and/or adding sprinkler heads. (IFC 901.4)
24: All new sprinkler systems and all modifications to existing sprinlder systems shall have fire department review and
approval of drawings prior to installation or modification. New sprinkler systems and all modifications to sprinkler
systems involving more than 50 heads shall have the written approval of the W.S.R.B., Factory Mutual, Industrial Risk
Insurers Kemper or any other representative designated and/or recognized by the City of Tukwila, prior to submittal to
the Tukwila Fire Prevention Bureau. No sprinlder work shall commence without approved drawings. (City Ordinance #2050)
25: All sprinkler system plans, calculations and the contractors Materials and Test Certificates submitted to the Tukwila
Fire Prevention Bureau must be stamped with the appropriate level of competency seal. (WAC 212 -80)
26: U.L. central station supervision is required. (City Ordinance #2050)
27: Maintain automatic fire detector coverage per N.F.P.A. 72. Addition/relocation of walls, closets or partitions may
require relocating and/or adding automatic fire detectors.
28: All new fire alarm systems or modifications to existing systems shall have the written approval of The Tukwila Fire
Prevention Bureau. No work shall commence until a fire department permit has been obtained. (City Ordinance #2051) (IFC
104.2)
doc: Cond -10/06
D08 -044 Printed: 02 -19 -2008
•
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206- 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
29: Local U.L. central station supervision is required. (City Ordinance #2051)
30: The installation of wiring and equipment shall be in accordance with N.F.P.A. 70, Article 760, Fire Protective
Signaling Systems. (NFPA 72- 1.3.3)
31: When the control panel is located inside a room, the door to the room shall have a sign with one -inch letters which
reads "Fire Alarm" or "Fire Alarm Control ". (City Ordinance #2051)
32: Dedicated fire alarm system circuit breaker(s) shall be equipped with a mechanical lockout device. (NFPA 72
(4.4.1.4.2.1))
33: Fire Department lock boxes shall be provided for access to all fire alarm panels and sprinkler risers. The appropriate
key(s) for access shall be placed in the lockbox. Lockbox order forms must be obtained from the Tukwila Fire
Department. The lockbox should be mounted so that it is readily visible and not over 60 inches high. (City Ordinance
#2051)
34: The Tukwila Fire Department has changed keybox manufacturers, from Supra to Knox. Install a fire department Knox
keybox. Contact the Tukwila Fire Prevention Office at 206 -575 -4407 for ordering information.
35: An electrical permit from the City of Tukwila Building Department Permit Center (206- 431 -3670) is required for this
project.
36: All electrical work and equipment shall conform strictly to the standards of the National Electrical Code. (NFPA 70)
37: An aisle to and working space shall be provided for each electrical panel. An aisle width not less than 24 inches shall
provide access to the panel and 30 inches of working space shall be provided directly in front of the panel. (NEC
110.26(A) thru F(2))
38: Each circuit breaker shall be legibly marked to indicate it's purpose. (NEC 110 -22)
39: Doors into electrical control panel rooms shall be marked with a plainly visible and legible sign stating "ELECTRICAL
ROOM" or similar approved wording. (IFC 605.3.1)
40: Required fire resistive construction, including occupancy separations, area separation walls, exterior walls due to
location on property, fire resistive requirements based on type of construction, draft stop partitions and roof
coverings shall be maintained as specified in the Building Code and Fire Code and shall be properly repaired, restored
or replaced when damaged, altered, breached, penetrated, removed or improperly installed. (IFC 703.1)
41: The maximum flame spread class of finish materials used on interior walls and ceilings shall not exceed that set forth
in Table No. 803.5 of the International Building Code.
42: When fire resistive floor or floor ceiling assemblies are required to prevent the vertical and horizontal spread of
fire and smoke, the assembly shall be maintained. (IBC 712.4.2)
43: New and existing buildings shall have approved address numbers, building numbers or approved building identification
placed in a position that is plainly legible and visible from the street or road fronting the property. These numbers
shall contrast with their background. Address numbers shall be Arabic numbers or alphabet letters. Numbers shall be a
minimum of 4 inches (102mm) high with a minimum stroke width of 0.5 inch (12.7mm). (IFC 505.1)
44: In order to provide you with the fastest police and fire protection under emergency conditions, please post your suite,
room or apartment number in a conspicuous place near the main entry door. (IFC 505.1)
45: Contact The Tukwila Fire Prevention Bureau to witness all required inspections and tests. (City Ordinances #2050 and
#2051)
doc: Cond -10/06
D08 -044 Printed: 02 -19 -2008
•
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206- 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
46: To schedule all construction fire - related inspections send an e -mail to fireinsprequest @ci.tukwila.wa.us. Include your
name, telephone number, permit number, project name and address and type of inspection requested.
47: Any overlooked hazardous condition and/or violation of the adopted Fire or Building Codes does not imply approval of
such condition or violation.
48: These plans were reviewed by Inspector 512. If you have any questions, please call Tukwila Fire Prevention Bureau at
(206)575 -4407.
doc: Cond -10/06
* *continued on next page **
D08 -044 Printed: 02 -19 -2008
Signature:
Print Name:
• •
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 - 431 -3665
Web site http: / /www.ci.tukwila.wa.us
I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and
this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provision of any other work
construction or the performance of work.
doc: Cond -10/06 D08 -044
Date: r2- 19-
'Gk
ordinances governing
or local laws regulating
Printed: 02 -19 -2008
CITY OF TUKWILP
Community Development Department
Public Works Department
Permit Center
6300 Southcenter Blvd., Suite 100
Tukwila, WA 98188
http://www.ci.tukwila.ivaus
SITE LOCATION
1 !! -- , King Co Assessor's Tax No.: Do 0
Site Address: /al (000 I n kvrb 6) .
Tenant Name: U n e //�� ��rr�
Property Owners Name: kgee-I
Mailing Address: J, O (qt2ieLthly br I vt tv) 00 TU guttia_
City
Name: C V 1d- f Jt1
Applications and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or by fax.
* *Please Print **
Mailing Address: 19149 A ,1- Dr. 6 V
E -Mail Address: d ii 1$d k&h iefilch atm
Company Name: - 1 - 7) 'E 'bETEPITh ED
Contact Person:
E -Mail Address:
Contractor Registration Number:
Company Name:
Mailing Address:
Contact Person:
E -Mail Address:
1911a boil w ► I ve 5
—
Building Permit No t . Q ti `I
Mechanical Permit No.
Plumbing/Gas Permit No.
Public Works Permit No.
Project No.
(For office use only)
Suite Number: / 1 0
New Tenant:
0003
Floor:
Yes ❑..No
1
9818
zip
CONTACT PERSON - who do we contact when your permit is ready to be issued
Day Telephone: d' 4'33 — b 9 q 7
eL WA 981(oS
Fax Number: iOL - ate - eat/
GENERAL CONTRACTOR INFORMATION —
(Contractor Information for Mechanical (pg 4) for Plumbing and Gas Piping (pg 5))
Mailing Address:
Zip
State
City
Day Telephone:
Fax Number:
Expiration Date:
ARCHITECT OF RECORD - All plans must be wet stamped by Architect of Record
6g WA yg rl(o'
City State Day Telephone: o/j i J , q 7
DAALL
d / 1-e,/ 1 d co/ 1 Fax Number: d fQ — M4D 4.-V0
ENGINEER OF RECORD - All plans must be wet stamped by Engineer of Record
Company Name:
Mailing Address:
City
Contact Person: Day Telephone:
E -Mail Address: Fax Number:
Q:WpplicationsTomts- Applications On Linr' -2006 - Permit Application Ann
Reviscd: 9 -2006
bh
State
Page 1 of 6
[iIJILDING PERMIT INFO ON — 206 -431 -3670
Q: ApplicattonsWotmaApptication sOn Linn 3 -2006 - Permit Apptimtion.doe
Revised: 9 -2006
bh
Valuation of Project (contractor's bid price): $ 7 500 Existing Building Valuation: $
Scope of Work (please provide detailed information): CO new of�7(.ei` n
�UY `K ltt,.
IY1.c lutt non beAr(n3 L(1 tal,PW alio/ 6t,(6p.Q./) cLeGL au) ci - eel/
Will there be new rack storage? ❑ Yes
0 . No If yes, a separate permit and plan submittal will be required.
Provide All Building Areas in Square Footage Below
PLANNING DIVISION:
Single family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches)
*For an Accessory dwelling, provide the following:
Lot Area (sq ft): Floor area of principal dwelling: Floor area of accessory dwelling:
*Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence.
Number of Parking Stalls Provided: Standard: Compact: Handicap:
Will there be a change in use? ❑ Yes ❑ No If `yes ", explain:
FIRE PROTECTION/HAZARDOUS MATERIALS:
X Sprinklers ❑ Automatic Fire Alarm ❑ None ❑ Other (specify)
Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ Yes ❑ No
If "yes', attach list of materials and storage locations on a separate 8-1/2" x 11 " paper including quantities and Material Safety Data Sheets.
SEPTIC SYSTEM
�\� ❑ ....... On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health
Department.
Page 2 of 6
Existing
Interior Remodel
Addition to
Existing
Structure
New
Type of
Construction per
IBC
Type of
Occupancy per
IBC
1� Floor
3 16-1 ` JF
.).5•5f
- • r 1
'.
2 Floor
3 Floor
Floors thru
Basement
Accessory Structure*
Attached Garage
Detached Garage
Attached Carport
Detached Carport
Covered Deck
Uncovered Deck
[iIJILDING PERMIT INFO ON — 206 -431 -3670
Q: ApplicattonsWotmaApptication sOn Linn 3 -2006 - Permit Apptimtion.doe
Revised: 9 -2006
bh
Valuation of Project (contractor's bid price): $ 7 500 Existing Building Valuation: $
Scope of Work (please provide detailed information): CO new of�7(.ei` n
�UY `K ltt,.
IY1.c lutt non beAr(n3 L(1 tal,PW alio/ 6t,(6p.Q./) cLeGL au) ci - eel/
Will there be new rack storage? ❑ Yes
0 . No If yes, a separate permit and plan submittal will be required.
Provide All Building Areas in Square Footage Below
PLANNING DIVISION:
Single family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches)
*For an Accessory dwelling, provide the following:
Lot Area (sq ft): Floor area of principal dwelling: Floor area of accessory dwelling:
*Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence.
Number of Parking Stalls Provided: Standard: Compact: Handicap:
Will there be a change in use? ❑ Yes ❑ No If `yes ", explain:
FIRE PROTECTION/HAZARDOUS MATERIALS:
X Sprinklers ❑ Automatic Fire Alarm ❑ None ❑ Other (specify)
Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ Yes ❑ No
If "yes', attach list of materials and storage locations on a separate 8-1/2" x 11 " paper including quantities and Material Safety Data Sheets.
SEPTIC SYSTEM
�\� ❑ ....... On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health
Department.
Page 2 of 6
PUBLIC WORKS PERMIT INFORMATION — 206 -433 -0179
Scope of Work (please provide detailed information):
Please refer to Public Works Bulletin #1 for fees and estimate sheet.
Water District
❑ ...Tukwila ❑...Water District #125
❑ ...Water Availability Provided
Sewer District
❑ ...Tukwila
❑ ...Sewer Use Certificate
❑... ValVue ❑ .. Renton
❑...Sewer Availability Provided
Septic System:
❑ On -site Septic System - For on -site septic system, provide 2 copies of a current septic design approved by King County Health Department.
Submitted with Application (mark boxes which apply):
❑ ...Civil Plans (Maximum Paper Size - 22" x 34")
❑ ...Technical Infonnation Report (Storm Drainage)
❑ ...Bond ❑ .. Insurance ❑ .. Easement(s)
Proposed Activities (mark boxes that apply):
❑ ...Right -of -way Use - Nonprofit for less than 72 hours
❑ ...Right -of -way Use - No Disturbance
❑ ...Construction/Excavation/Fill - Right -of -way
Non Right -of -way
❑ ...Total Cut cubic yards
❑ ...Total Fill cubic yards
❑ ...Sanitary Side Sewer ❑ .. Abandon Septic Tank
❑ ...Cap or Remove Utilities ❑ .. Curb Cut
❑ ...Frontage Improvements ❑ .. Pavement Cut
❑ ...Traffic Control ❑ .. Looped Fire Line
❑ ... Backflow Prevention - Fire Protection
Irrigation
Domestic Water
QAApplianions\Foma-Applications On Line \3 -2006. Pamir Application.doc
Revised: 9 - 206
bh
Call before you Dig: 1- 800- 424 -5555
❑ .. Highline
❑ .. Geotechnical Report
❑ .. Maintenance Agreement(s)
❑ .. Work in Flood Zone
❑ .. Storm Drainage
❑ .. Renton
❑ .. Seattle
❑ .. Right -of -way Use - Profit for less than 72 hours
❑ .. Right -of -way Use - Potential Disturbance
El... Traffic Impact Analysis
El... Hold Harmless - (SAO)
❑ ...Hold Harmless - (ROW)
❑ .. Grease Interceptor
❑ .. Channelization
❑ .. Trench Excavation
❑ .. Utility Undergrounding
❑ ...Permanent Water Meter Size... 71 WO #
❑ ...Temporary Water Meter Size .. WO #
❑ ...Water Only Meter Size WO # ❑...Deduct Water Meter Size
❑ ...Sewer Main Extension Publ:.c Private
❑ ...Water Main Extension Public Private _ ___
FINANCE INFORMATION
Fire Line Size at Property Line Number of Public Fire Hydrant(s)
❑ ...Water ❑ ...Sewer ❑ ...Sewage Treatment
Monthly Service Billing to:
Name: Day Telephone:
Mailing Address:
City State Zip
Water Meter Refund/Billing:
Name:
Mailing Address:
Day Telephone:
City State
ZiP
Page 3 of 6
Unit Type:
Qty
Unit Type:
Qty
Unit Type:
Qty
Boiler /Compressor:
Qty
Furnace <100K BTU
Air Handling Unit >10,000
CFM
Fire Damper
0 -3 HP /100,000 BTU
Furnace >100K BTU
Evaporator Cooler
Diffuser
3 -15 HP /500,000 BTU
Floor Furnace
Ventilation Fan Connected
to Single Duct
Thermostat
15 -30 HP /1,000,000 BTU
Suspended/Wall/Floor
Mounted Heater
Ventilation System
Wood/Gas Stove
30-50 HP /1,750,000 BTU
Appliance Vent
Hood and Duct
Emergency
Generator
50+ HP /1,750,000 BTU
Repair or Addition to
Heat/Refrig/Cooling
System
Incinerator - Domestic
Other Mechanical
Equipment
Air Handling Unit
<10,000 CFM
Incinerator — Comm/lnd
MECHANICAL PERMIT INFO TION - 206 -431 -3670
MECHANICAL CONTRACTOR INFORMATION
Company Name:
Mailing Address:
City State Zip
O Person: Day Telephone:
E -Mail Address: Fax Number:
Contractor Registration Number: Expiration Date:
Valuation of Mechanical work (contractor's bid price): $
Scope of Work (please provide detailed information):
Use: Residential: New .... ❑ Replacement .... ❑
Commercial: New .... ❑ Replacement .... ❑
Fuel Type: Electric ❑ Gas ....0 Other:
Indicate type of mechanical work being installed and the quantity below:
Q:Wpplicationa\For ms- Applications On Iinc\3.2006 - Permii Applimtiondoc
Revisrd: 9 -2006
bh
Page 4 of 6
Fixture Type:
Qty
Fixture Type:
Qty
Fixture Type:
Qty
Fixture Type:
Qty
Bathtub or combination
bath/shower
Drinking fountain or water
cooler (per head)
Wash fountain
Gas piping outlets
Bidet
Food -waste grinder,
commercial
Receptor, indirect
waste
Clothes washer, domestic
Floor drain
Sinks
Dental unit, cuspidor
Shower, single head trap
Urinals
Dishwasher, domestic,
with independent drain
Lavatory
Water Closet
Building sewer or trailer
park sewer
Rain water system - per
drain (inside building)
Water heater and/or
vent
Additional medical gas
inlets /outlets — six or more
Industrial waste
pretreatment interceptor,
including its trap and vent,
except for kitchen type
grease interceptors
Repair or alteration of water
piping and/or water treating
equipment
Repair or alteration
of drainage or vent
piping
Medical gas piping system
serving one to five
inlets/outlets for specific gas
PLUMBING AND GAS PIPING INFORMATION - 206 - 431 -3670
PLUMBING AND GAS PIPING CONTRACTOR INFORMATION
Company Name:
Mailing Address:
City State Zip
Contact Person: Day Telephone:
E -Mail Address: Fax Number:
Contractor Registration Number: Expiration Date:
Valuation of Plumbing work (contractor's bid price): $
Valuation of Gas Piping work (contractor's bid price): $
Scope of Work (please provide detailed information):
Building Use (per Intl Building Code):
Occupancy (per Intl Building Code):
Utility Purveyor: Water: Sewer:
Indicate type of plumbing fixtures and/or gas piping outlets being installed and the quantity below:
Q_ Appl nun ions Fomw.Applieetions On LineO -2006 - Pamil Appl jean on.doc
Revised: 9 -2006
bh
Page 5 of 6
PERMIT APPLICATION NOTES — Applicable to all permits in this application
Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject
to possible revision by the Permit Center to comply with current fee schedules.
Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation.
Building and Mechanical Permit
The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be
requested in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition).
Plumbing Permit
The Building Official may grant one extension of time for an additional period not exceeding 180 days. The extension shall be requested
in writing and justifiable cause demonstrated Section 103.4.3 Uniform Plumbing Code (current edition).
I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER
PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT.
BUILDING OWNER OR AUTHO ED AGENT:
Signature: Date: 1- -QQ
I -0 D
Print Name: ,A I l) J' Day Telephone: 0 - �3, - E3"I q7
Mailing Address: i GJ / (Q & Der v/, 60 .oe aizta (,d1 ft 6 1 9 11043
City S&au. Zip
Date Application Expires:
7 - d8
Date Application Accepted: j
Q:\App caliona\Fomia- Applications On LincU -2006 - Pmnn Applimtion.doc
Revised: 9 -2006
bh
Staff Initials:
Page 6 of 6
Receipt No.: R08 -00457
Initials: WER
User ID: 1655
Payee: PRECISION BUILDERS
ACCOUNT ITEM LIST:
Description
don: RAr. int -0R
BUILDING - NONRES
STATE BUILDING SURCHARGE
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 -431 -3665
Web site: http: / /www.ci.tukwila.wa.us
RECEIPT
Parcel No.: 0004800003 Permit Number: D08 -044
Address: 12600 INTERURBAN AV S TUKW Status: APPROVED
Suite No: Applied Date: 01/29/2008
Applicant: GE Issue Date:
TRANSACTION LIST:
Type Method Description Amount
Payment Check 20653 201.00
Account Code Current Pmts
000/322.100
000/386.904
Payment Amount: $201.00
Payment Date: 02/19/2008 08:53 AM
Balance: $0.00
196.50
4.50
Total: $201.00
8789 02/19 9710 TOTAL 201.00
Printarl• 09 -19 -9008
Payee: DAVID KEHLE ARCHITECTS
ACCOUNT ITEM LIST:
Description
PLAN CHECK - NONRES
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 -431 -3670
Fax: 206 -431 -3665
Web site: http. / /www.ci.tukwila.wa.us
RECEIPT
Parcel No.: 0004800003 Permit Number: D08 -044
Address: 12600 INTERURBAN AV S TUKW Status: PENDING
Suite No: Applied Date: 01/29/2008
Applicant: GE Issue Date:
Receipt No.: R08 -00251 Payment Amount: $127.73
Initials: WER Payment Date: 01/29/2008 02:05 PM
User ID: 1655 Balance: $201.00
TRANSACTION LIST:
Type Method Description Amount
Payment Check 18188 127.73
Account Code Current Pmts
000/345.830 127.73
Total: $127.73
•
7774 01/29 9710 TOTAL 127.73
doc: Receiot -06 Printed: 01 -29 -2008
Project:
(� re
Type of Inspec I9n:
6u `I .4., /I / 1 - ) Ai p
Address:
Date Called:
Special Instructions:
Date Wanted: 3
6- - .:
a.m
p.m.
Requester:
Phone No:
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO. PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670
Approved per applicable codes. Corrections required prior to approval.
COMMENTS:
7 I ?`1,1 1. =::L ) +'
$58.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd.. Suite 100. Call the schedule reinspection.
Receipt No.:
'Date:
,:;.maam• s..+y+, . ••■ »..; • • •
Project: ,, -
!--,
( . -
J Type of Inspection
t)-s -- � . e�
r I
l , , A../ ( - . -.y
Address:
Date Callid:
/
Special Instructions:
Date Wanted:
.,
" S
J Y
.a. m.
p.m
Requester:
Phone No:
INSPECTION NO.
INSPECTION RECORD
Retain a copy with permit
PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION 'R
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670
Approved per applicable codes. Corrections required prior to approval.
COMMENTS:
Inspector:
Date: 65. 5
0 $58.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd.. Suite 100. Call the schedule reinspection.
Receipt No.:
'Date:
•
Project:
E =
Type of Inspection
it-L5 eA, c- e, (
A
Address:
I 2 (4 0 a
■rd ai iiM A-
Date Cal ed:
)4_ S e
�—
Special Instructions:
Date Wanted:
3-(r7— J 8'.
- .._.4.134 - ."
,
p.m.
Requester:
Phone No:
TO (AP "' 31 - /53 d
Ler
INSPECTION NO.
INSPECTION RECORD
Retain a copy with permit
PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION R
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670
Approved per applicable codes.
orrections required prior to approval.
COMMENTS:
1
Date: 3 Jer5
Inspectdr:
$58.00 REINSPECTION FEE REQUIRED. Prior o inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call the schedule reinspection.
Receipt No.:
Date:
Project: GE
Sprinklers:
Type of Inspection:
. fell •el "ZIT .A. C.:viv ff.;
Address: / Za. 40.2 vo
Suite #:1 /0
4 je. s .
Contact Person:
Special Instructions:
Occupancy Type:
Phone No.:
Needs Shift Inspection:
Sprinklers:
Fire Alarm:
Hood & Duct:
Monitor:
Pre -Fire:
Permits:
Occupancy Type:
V
I
INSPECTION NUMBER
INSPECTION RECORD
Retain a copy with permit
CITY OF TUKWILA FIRE DEPARTMENT
Andover Park East, Tukwila, Wa. 98188 206- 575 -4407
M ./ Approved per applicable codes.
COMMENTS:
S !C 1 aC !C
G T / - / Ca m
Inspector:
Date: 3 /C /oe
rs..
l
$80:00 REINSPECTION FEE REQUIRED. You will receive an invoice from
the City of Tukwila Finance Department. Call to schedule a reinspection.
Word /Inspection Record Form.Doc 1/13/06
- 0 4/y
OP- 5-0'17
PERMIT NUMBERS
Corrections required prior to approval.
T.F.D. Form F.P. 113
f
Project:
(ac
Type of Inspection:
,f24 IJ K
Ac DO ��
,, (( �r,�bg� /
D to Called:
s
Special Instructions:
-
Date ?a i d: �, G Grp.
Requester:
Phone No
,,Q4 - ..EL- 4536
INSPECTION RECORD
Retain a copy with permit bog' ovV
PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION 12-
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3 7
7,
r.<
COMMENTS:
INSPECTION NO.
proved per applicable codes. Corrections required prior to approval. ZZ
Re eipt No.:
Ai /
0
0 REINSPECTION FEEREQUI
at 6300 Southcenter B d., S ui
Date
D . Prior o inspection, fed must be
e 100. Call the schedule reinspection.
Date:
l
. .:.% ,..` t ' . `SLY • =�. f:d ^ '�1` :i�,;$34A • .:.:: ila
PType
C.,
of Insp ction:
etil i / ._.rA/S .
\J
Address:
G49 .-
ii/rr 21 ✓4 #07
Date Called:
Special Instructions:
Date / 0,60
//
vg
Requester:
Phone 20e*— 1 I r `..'
3
INSPECTION RECORD
Retain a copy with permit
Doca —6444
PERMIT NO. c 7
CITY OF TUKWILA BUILDING DIVISION g.
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 - 6 0
INSPECTION NO.
R Approved per applicable codes. El Corrections required prior to approval.
COMMENTS:
Date:
2- 7 -v
$58.00 REINSP ION FEE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd.. Suite 100. Call the schedule reinspection.
Receipt No.:
Date:
• A•. 1M� Li'iR e�3'
Project Info
Project Address
FLU, commEgag PARK
Date 1/24/2008
12600 INTERURBAN AVE. S., SUITE 110
For Building Department Use
TUKWILA, WASHINGTON
Applicant Name:
DAVID KEHLE, ARCHITECT
Applicant Address:
1916 BONAIR DRIVE S.W. , SEATTLE, WA.
Applicant Phone:
206- 433 -8997
7
w
Project Si mmary
PRJ -SUM
2006 Washington State Nonresidential Energy Code Compliance Forms
2006 Washington State Nonresidential Ener• y Code Compliance Form
SOS - 0 99
•+wpq r. 4
FILE C
Revised July 2007
JAN 2 9 2008
.DER
Location
(floor /room no.)
Occupancy Description
Allowed
Watts per ft **
Area in fix
Allowed x Area
1
OFFICE
1.00
250.0
250.0
existing warehouse, no change to wattage, 0.5 /s.f. max.
** From Table 15-1 (over) - document all exceptions on form LTG -LPA Total Allowed Watts
250.0
..
Location
(floor /room no.)
v v
Fixture Description
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
1
recessed 2'x4' 2 -tube, T -8 fluor. WI electronic ballist
3
66.0
198.0
Total Proposed Watts may not exceed Total Allowed Watts for Interior Total Proposed Watts
198.0
2006 Washington State Nonresidential Energy Code Compliance Form
Inte Lighting Summary
LTG -INT
2008 Washington State Nonresidential Energy Code Compliance Forms
Revised July 2007
Project Info
Project Address
TOXEMIA c05 ERCE PARK
32600 INTERURBAN AVE. S., SUITE 110
TUKWILA, WASHINGTON
Applicant Name: DAVID KEHLE, ARCHITECT
Applicant Address: 1916 BONAIR DRIVE S.W., SEATTLE, WA.
Applicant Phone: 206 - 433 -8997
Date
1/24/2008
For Building Department Use
Project Description
❑ New Building ❑ Addition 0 Alteration ❑ Plans Induded
Refer to WSEC Section 1513 for controls and commissioning requirements.
Compliance Option
O Prescriptive 0 Lighting Power Allowance 0 Systems Analysis
(See Qualification Checklist (over). Indicate Prescriptive & LPA spaces clearly on plans.)
Alteration Exceptions
(check appropriate box - sec. 1132.3)
❑ No changes are being made to the lighting
❑ Less than 60% of the fixtures new, installed wattage not increased, & space use not changed.
Maximum Allowed Lighting Wattage
Provosed Lighting Wattage
Notes:
1. For proposed Fixture Description, indicate fixture type, lamp type (e.g. T-8), number of lamps in the fixture, and ballast type (if
included). For track lighting, list the length of the track (in feet) in addition to the fixture, lamp, and ballast information.
2. For proposed Watts/Fixture, use manufacturer's listed maximum input wattage of the fixture (not simply the lamp wattage) and
other criteria as specified in Section 1530. For hard -wired ballasts only, the default table in the NREC Technical Reference Manual
may also be used. For track lighting, list the greater of actual luminaire wattage or length of track multiplied by 50, or as applicable,
the wattage of current limiting devices or of the transformer.
3. List all fixtures. For exempt lighting, note section and exception number, and leave Watts/Fixture blank.
Use'
LPA` (W/sf)
Use'
LPA` (W /sf)
Automotive facility
0.9
Office buildings, office/administrative areas in
facilities of other use types (including but not limited
to schools hospitals, institutions, museums, banks,
churches) ,
1.0
Convention center
1.2
Penitentiary and other Group 1 -3 Occupancies
1.0
Courthouse
1.2
Police and fire stations
1.0
Cafeterias, fast food establishments',
restaurants/bars
1.3
Post office
1.1
Dormitory
1.0
Retail", retail banking, mall concourses, wholesale
stores (pallet rack shelving)
1.5
Exercise center
1.0
School buildings (Group E Occupancy only), school
classrooms, day care centers
1.2
Gymnasia assembly spaces
1.0
Theater, motion picture
1.2
Health care clinic
1.0
Theater, performing arts
1.6
Hospital, nursing homes, and other Group I -1 and
1 -2 Occu . ancies
1.2
Transportation
Warehous s , storage areas
1.0
0.5
Hotel/motel
1.0
Hotel banquet/conference/exhibition hall'`
2.0
Workshops
1.4
Laboratory spaces (all spaces not classified
"laboratory" shall meet office and other appropriate
categories)
1.8
Parking garages
0.2
Laundries
1.2
Libraries'
1.3
Plans Submitted for Common Areas Only'
Manufacturing facility
1.3
Main floor building lobbies' (except mall concourses)
Common areas, corridors, toilet facilities and
washrooms, elevator lobbies
1.2
0.8
Museum
1.1
Prescriptive Spaces
Occupancy:
Q Warehouses, storage areas or aircraft storage hangers 0 Other
Qualification Checklist
Note: If occupancy type is "Other" and fixture
answer is checked, the number of fixtures in
the space is not limited by Code. Cleary
indicate these spaces on plans. If not
qualified, do LPA Calculations.
Lighting
Fixtures:
(Section
1521)
Check if 95% or more of fixtures comply with 1,2 or 3 and rest are ballasted.
1. Fluorescent fixtures which are non - lensed with a) 1 or 2 two lamps, b) reflector
or louvers, c) 5-60 watt T -1, T -2, T -4, T -5, T-8 lamps, and d) hard -wired elect
tronic dimming ballasts. Screw -in compact fluorescent fixtures do not qualify.
2. Metal Halide with a) reflector b) ceramic MH lamps <= 150w c) electronic ballasts
3. LED lights.
Interior Lighting Summary (back)
LTG -INT
2006 Washington State Nonresidential Energy Code Compliance Forms
- Un it Lighting Power Allo ( LPA
2006 Washington State Nonresidential Energy Code Compliance Form
Revised July 2007
Footnotes for Table 15 -1
1) In cases in which a general use and a specific use are listed, the specific use shall apply. In cases In which a use is not mentioned
specifically, the Unit Power Allowance shall be determined by the building official. This determination shall be based upon the most
comparable use specified in the table. See Section 1512 for exempt areas.
2) The watts per square foot may be increased, by two percent per foot of ceiling height above twenty feet, unless specifically directed
otherwise by subsequent footnotes.
3) Watts per square foot of room may be increased by two percent per foot of ceiling height above twelve feet.
4) For all other spaces, such as seating and common areas, use the Unit Light Power Allowance for assembly.
5) Watts per square foot of room may be increased by two percent per foot of ceiling height above nine feet.
6) Reserved.
7) For conference rooms and offices less than 150ft with full height partitions, a Unit Lighting Power Allowance of 1.10 w/ft may be used.
8) Reserved.
9) For indoor sport tournament courts with adjacent spectator seating over 5,000, the Unit Lighting Power Allowance for the court area is
2.60 W/ft
10) Display window illumination installed within 2 feet of the window, provided that the display window is separated from the retail space by
walls or at least three - quarter - height partitions (transparent or opaque). and lighting for free - standing display where the lighting moves
with the display are exempt.
An additional 1.5 w/ft of merchandise display luminaires are exempt provided that they comply with all three of the following:
a) located on ceiling- mounted track or directly on or recessed into the ceiling itself (not on the wall).
b) adjustable in both the horizontal and vertical axes (vertical axis only is acceptable for fluorescent and other fixtures with two points
of track attachment).
c) fitted with LED, tungsten halogen, fluorescent, or high intensity discharge lamps.
This additional lighting power is allowed only if the lighting is actually installed.
11) Provided that a floor plan, indicating rack location and height, is submitted, the square footage for a warehouse may be defined, for
computing the interior Unit Lighting Power Allowance, as the floor area not covered by racks plus the vertical face area (access side only)
of the racks. The height allowance defined in footnote 2 applies only to the floor area not covered by racks.
Project Info
Proj Addles' TUKSILIA cc PARR
Date 1/24/2008
12600 INTERURBAN AVE. S., SUITE 110
For Building Department Use
TUKWILA, WASHINGTON
Name: DAVID MIME ARCHITECT
AppI. Name 1916 BONAIR DRIVE S.W., SEATTLE, WA.
Appl. Phone
206 -433 -8997
Project Description
❑ Plans Included
requirements.
❑ New ❑ Addition J Alteration
Refer to WSEC Section 1513 for controls and commissioning
Compliance Option I
O Lighting Power Allowance 0 Systems Analysis
Building Grounds
(luminaires > 100 Watts)
❑ Efficacy > 60 lumens/W [] Controlled by motion Sensor
❑ Exemption (list)
Alteration Exceptions
(check appropriate box - sec. 1132.3)
.1 No changes are being made to the lighting
❑ Less than 60% of the fixtures new, installed wattage not increased, & space use not changed.
Tradable Locations
.. v v
Description
Allowed Watts
per ft or per If
Area (ft), perimeter
(If) or # of items
Allowed Watts
x ft (or x If)
•
Non - Tradable Locations
Description
Allowed Watts
per ft or per If
Area (ft perimeter
(If) or # of items
Allowed Watts
x ft (or x If)
Location
Fixture Description
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
Location
Fixture Description
Number of
Fixtures
Watts/
Fixture
Watts
Proposed
f
2006 Washington State Nonresidential Energy Code Compliance Forma
2006 Washin ! ton State Nonresidential Energy Code Compliance Form
Exterior Lighting Summary
LTG -EXT
Revised July 2007
Tradable Maximum Allowed Lighting Wattage
Tradable Proposed Lighting Wattage
otat Anowee wa
Use mfgr listed maximum input wattage. For fixtures with hard -wired ballasts only,
the default table in the NREC Technical Reference Manual may also be used.
Total Proposed Watts may not exceed Total Allowed Watts for Exterior
Non - Tradable Maximum Allowed Lighting Wattage
otal Proposed Wa
Non - Tradable Proposed Lighting Wattage
Proposed Watts may not exceed Allowed Watts for Category
Tradable Surfaces
(Lighting power
densities for uncovered
parking areas, building
grounds, building
entrances and exits,
canopies and overhangs
and outdoor sales areas
may be traded.)
Uncovered Parking Areas
Parking lots and drives
0.15 W/ft
Building Grounds
Walkways less than 10 feet wide
1.0 W /linear foot
Walkways 10 feet wide or greater
plaza areas
Special feature areas
0.2W/ft
Stairways
1.0 W/ft
Building Entrances and Exits
Main entries
30 W/linear foot of door width
Other doors
20 W/linear foot of door width
Canopies and Overhangs
Canopies (free standing and attached and
overhangs)
1.25 W/ft
Outdoor Sales
Open areas (including vehicle sales lots)
0.5 W/ft
Street frontage for vehicle sales lots in
addition to "open area" allowance
20 W/linear foot
Non - Tradable
Surfaces (Lighting
power density
calculations for the
following applications
can be used only for the
specific application and
cannot be traded
between surfaces or
with other exterior
lighting. The following
allowances are in
addition to any
allowance otherwise
permitted in the
"Tradable Surfaces"
section of this table.)
Building Facades
0.2 W/ft for each illuminated wall or
surface or 5.0W/linear foot for each
illuminated wall or surface length
Automated teller machines and night
depositories
270 W per location plus 90 W per
additional ATM per location
Entrances and gatehouse inspection
stations at guarded facilities
1.25 W/ft of uncovered area (covered
areas are included in the "Canopies
and Overhangs" section of "Tradable
Surfaces ")
Loading areas for law enforcement,
fire, ambulance and other emergency
service vehicles
0.5 W/ft f uncovered area (covered
areas are included in the "Canopies
and Overhangs" section of "Tradable
Surfaces ")
Material handling and associated
storage
0.5 W /ft
Drive -up windows at fast food
restaurants
400W per drive- through
Parking near 24-hour retail entrances
800 W per main entry
Exterior Lighting Summary (back)
LTG -EXT
2006 Washington State Nonresidential Energy Code Compliance Forms
2006 Washington State Nonresidential Energy Code Compliance Form
TABLE 15 -2
LIGHTING POWER DENSITIES FOR BUILDING EXTERIORS
Revised July 2007
I
2006 Washington State Nonresidential Energy Code Compliance Form
LTG -LPA
Ligh P Allowance Adjustments
2006 Washington State Nonresidential Energy Code Compliance Forms
Date
1/24/2008
Project Address I Th comer= pARK
Use this form if you are claiming any ceiling height adjustments for your Lighting Power Allowances for interior lighting. The
Occupancy Description should agree with the "Use" listed on Code Table 15-1. Identify the appropriate Ceiling Height Limit (9 feet,
12 feet or 20 feet) on which the adjustment is based. The Adjusted LPA is calculated from this number and from the Allowed Watts
per ft Carry the Adjusted LPA to the corresponding "Allowed Watts per ft location on LTG -SUM.
Adjusted LiOhting Power Allowances (Interior)
" From Table 15-1 based on exceptions listed in footnotes
Revised July 2007
Location
(floor /room no.)
Occupancy Description
Allowed
Watts per ft '"
Ceiling Height
for this room
Ceiling Height limit
for this exception"
Adjusted LPA
Watts per ft2
•I 1• (i• • .1. .1 • 11 11 .1 1- . ■
2008 Washington State Nonresidential Energy Code Compliance Forms Revised July 2007
Project Address TUIOILIA COMIERCE P 'Date
1/24/2008
The following information is necessary to check a permit application for compliance with the lighting, motor, and transformer requirements
in the 2006 Washington State Nonresidential Energy Code.
Applicability I
es, no, n.a. )
Code
Section
Component 'Information Required I
Location
on Plans
Building Department
Notes
LIGHTING CONTROLS
(Section 1513)
yes
1513.1
Local control/access
Schedule with type, indicate locations
yes
1513.2
Area controls
Maximum limit per switch
yes
1513.3
Daylight zone control
Schedule with type and features, indicate locations
yes
vertical glazing
Indicate vertical glazing on plans
.. a.
overhead glazing
Indicate overhead glazing on plans
a.
1513.4
Display /exhib /special
Indicate separate controls
1513.5
Exterior shut -off
Schedule with type and features, indicate location
-
a.
(a) timer w/backup
Indicate location
a.
(b) photocell.
Indicate location
1513.6
Inter. auto shut -off
Indicate location
a.
1513.6.1
(a) occup. sensors
Schedule with type and locations
a.
1513.6.2
(b) auto. switches
Schedule with type and features (back -up, override capability);
Indicate size of zone on plans
.. a.
1513.7
Commissioning
Indicate requirements for lighting controls commissioning
EXIT SIGNS
(Section 1514)
a.
LIGHTING POWER
I 1514
ALLOWANCE
IMax. watts
(Section
'Indicate watts for each exit sign
1530 -1532)
I
I
yes
1531
Interior Lighting
Summary Form
Completed and attached. Schedule with fixture types,
lamps, ballasts, watts per fixture
T -1
.. a.
1532
Exterior Lighting
Summary Form
Completed and attached. Schedule with fixture types,
lamps, ballasts, watts per fixture
MOTORS (Section
a.
1511)
I 1511
IElec motor efficiency
IMECH -MOT or Equipment Schedule with hp, rpm, efficiency
I
L
'
TRANSFORMERS
(Section 1540)
..a.
1 1540
'Transformers
'Indicate size and efficiency
I
I
2006 Washin• on State Nonresidential Ener• Code Corn !lance Form
If "no" Is circled for any question, provide explanation:
2006 Washin• ton State Nonresidential Ene • Code Com liance Form
Light ing, d Compliance
ting andTransformer Permit Plans Checklist LTG -CHK
2006
Revised July 2007
Lighting - General Requirements
1513 Lighting Controls: Lighting, including exempt lighting
in Section 1512, shall comply with this section. Where
occupancy sensors are cited, they shall have the features
listed in Section 1513.6.1. Where automatic time switches
are cited, they shall have the features listed in Section
1513.6.2.
1513.1 Local Control and Accessibility: Each space,
enclosed by walls or ceiling- height partitions, shall be
provided with lighting controls located within that space. The
lighting controls, whether one or more, shall be capable of
tuming off all lights within the space. The controls shall be
readily accessible, at the point of entry/exit, to personnel
occupying or using the space.
EXCEPTIONS: The following lighting controls may be
centralized in remote locations:
1. Lighting controls for spaces which must be used as
a whole.
2. Automatic controls.
3. Controls requiring trained operators.
4. Controls for safety hazards and security.
1513.2 Area Controls: The maximum lighting power that
may be controlled from a single switch or automatic control
shall not exceed that which is provided by a 20 ampere circuit
loaded to not more than 80 %. A master control may be
installed provided the individual switches retain their capability
to function independently. Circuit breakers may not be used
as the sole means of switching.
EXCEPTIONS: 1. Industrial or manufacturing process
areas, as may be required for production.
2. Areas less than 5% of the building footprint for
footprints over 100,000 ft
1513.3 Daylight Zone Control: All daylighted zones, as
defined in Chapter 2, both under overhead glazing and
adjacent to vertical glazing, shall be provided with individual
controls, or daylight- or occupant- sensing automatic controls,
which control the lights independent of general area lighting.
Contiguous daylight zones adjacent to vertical glazing are
allowed to be controlled by a single controlling device
provided that they do not include zones facing more than two
adjacent cardinal orientations (i.e. north, east, south, west).
Daylight zones under overhead glazing more than 15 feet
from the perimeter shall be controlled separately from daylight
zones adjacent to vertical glazing.
EXCEPTION: Daylight spaces enclosed by walls or
ceiling height partitions and containing 2 or fewer light
fixtures are not required to have a separate switch for
general area lighting.
1513.4 Display, Exhibition and Specialty Lighting
Controls: All display, exhibition or specialty lighting shall be
controlled independently of general area lighting.
1513.5 Automatic Shut -off Controls, Exterior: Lighting for
all exterior applications shall have automatic controls capable
of turning off exterior lighting when sufficient daylight is
available or when the lighting is not required during nighttime
hours. Lighting not designated for dusk -to -dawn operation
shall be controlled by either.
a. A combination of a photosensor and a time switch;
or
b. An astronomical time switch.
Lighting designated for dusk -to -dawn operation shall be
controlled by an astronomical time switch or photosensor. All
time switches shall be capable of retaining programming and
the time setting during loss of power for a period of at least 10
hours.
EXCEPTION: Lighting for covered vehicle entrances
or exits from buildings or parking structures where
required for safety, security, or eye adaptation.
1513.6 Automatic Shut -Off Controls, Interior. Buildings
greater than 5,000 ft and all school classrooms shall be
equipped with separate automatic controls to shut off the
lighting during unoccupied hours. Within these buildings, all
office areas less than 300 ft enclosed by walls or ceiling -
height partitions, and all meeting and conference rooms, and
all school classrooms, shall be equipped with occupancy
sensors that comply with Section 1513.6.1. For other spaces,
automatic controls may be an occupancy sensor, time switch
or other device capable of automatically shutting off lighting.
EXCEPTIONS: 1. Areas that must be continuously
illuminated in a manner requiring manual operation of
the lighting.
2. Emergency lighting systems.
3. Switching for industrial or manufacturing process
facilities as may be required for production.
4. Hospitals and laboratory spaces.
5. Areas in which medical or dental tasks are
performed are exempt from the occupancy sensor
requirement.
1513.6.1 Occupancy Sensors: Occupancy sensors shall
be capable of automatically turning off all the lights in an
area, no more than 30 minutes after the area has been
vacated.
Light fixtures controlled by occupancy sensors shall have a
wall- mounted, manual switch capable of turning off lights
when the space is occupied.
EXCEPTION: Occupancy sensors in stairwells are
allowed to have two step lighting (high -light and low -
light) provided the control fails in the high -light position.
1513.6.2 Automatic Time Switches: Automatic time
switches shall have a minimum 7 day dock and be capable
of being set for 7 different day types per week and
incorporate an automatic holiday "shut -ofr feature, which
turns off all loads for at least 24 hours and then resumes
normally scheduled operations. Automatic time switches
shall also have program back -up capabilities, which prevent
the loss of program and time settings for at least 10 hours, if
power is interrupted.
Automatic time switches shall incorporate an over -ride
switching device which:
a. is readily accessible;
b. is located so that a person using the device can see the
lights or the areas controlled by the switch, or so that the
area being illuminated is annunciated;
c. is manually operated;
d. allows the lighting to remain on for no more than 2 hours
when an over -ride is initiated; and
e. controls an area not exceeding 5,000 ft or 5% of the
building footprint for footprints over 100,000 ft whichever is
greater.
1513.7 Commissioning Requirements: For lighting
controls which include daylight or occupant sensing
automatic controls, automatic shut -off controls, occupancy
sensors, or automatic time switches, the lighting controls
shall be tested to ensure that control devices, components,
equipment and systems are calibrated, adjusted and operate
in accordance with approved plans and specifications.
Sequences of operation shall be functionally tested to
ensure they operate in accordance with approved plans and
specifications. A complete report of test procedures and
results shall be prepared and filed with the owner. Drawing
notes shall require commissioning in accordance with this
paragraph.
1514 Exit Signs: Exit signs shall have an input power
demand of 5 Watts or less per sign.
Motors - General Requirements
1511 Electric Motors: All permanently wired polyphase
motors of 1 hp or more, which are not part of an HVAC
system, shall comply with Section 1437.
EXCEPTIONS: 1. Motors that are an integral part of
specialized process equipment.
2. Where the motor is integral to a listed piece of
equipment for which no complying motor has been
approved.
Transformers - General Requirements
SECTION 1540 — TRANSFORMERS
The minimum efficiency of a low voltage dry-type
distribution transformer shall be the Class I Efficiency Levels
for distribution transformers specified in Table 4 -2 of the
"Guide for Determining Energy Efficiency for Distribution
Transformers° published by the National Electrical
Manufacturers Association (NEMA TP- 1- 2002).
Opaque Concrete/Masonry Wall Requirements
Wall Maximum U- factor is 0.15 (R5.7 continuous ins)
CMU block walls with insulated cores comply
If project qualifies for Concrete /Masonry Option, list walls
with HC z 9.0 Btu/ft . °F below (other walls must meet
Opaque Wall requirements). Use descriptions and values
from Table 10-9 in the Code.
Wall Description
(including insulation R -value & position)
U- factor
Concrete/Masonry Option
All Other Roofs
Date 1/24/2008
30. 0
Opaque Walls'
S.,
19. 0
Below Grade Walls
C lr-J C C.. .. .. •. .. ,..,_ i
For Building Department Use
L�
COPY
Floors Over Unconditioned Space
Tukwila, Washington
Slabs -on -Grade
lUI
Radiant Floors
David Kahle, Architect
Maximum U- factors
Opaque Doors
Applicant Address:
0. 600
Vertical Glazing
Envelope Requirements (enter values as applicable)
Project Address
Minimum Insulation R- values
Roofs Over Attic
24.0 - 766.0 X 100 = 3.1%
Concrete/Masonry Option
All Other Roofs
Date 1/24/2008
30. 0
Opaque Walls'
S.,
19. 0
Below Grade Walls
For Building Department Use
L�
COPY
Floors Over Unconditioned Space
Tukwila, Washington
Slabs -on -Grade
lUI
Radiant Floors
David Kahle, Architect
Maximum U- factors
Opaque Doors
Applicant Address:
0. 600
Vertical Glazing
Overhead Glazing
Applicant Phone:
206 - 433 -8997
Maximum SHGC (or SC)
VerticallOverhead Glazing
� `
Project Info
Project Address
mama coompaE PARK
Total Glazing Area Electronic version: these values are automatically taken from ENV -UA -1.
(rough opening) Gross Exterior
(vertical & overhd) divided by Wall Area times 100 equals % Glazing
24.0 - 766.0 X 100 = 3.1%
Concrete/Masonry Option
0 yes Check here if using this option and if project meets all requirements for the Concrete/Masonry
no Option. See Decision Flowchart (over) for qualifications. Enter requirements for each qualifying
assembly below.
Date 1/24/2008
12600 INTERURBAN AVE.
S.,
SUITE
110
For Building Department Use
L�
COPY
Tukwila, Washington
lUI
Applicant Name:
David Kahle, Architect
/F
Applicant Address:
1916 Bonair Drive S.W.
PrAvrtylpe
Applicant Phone:
206 - 433 -8997
� `
Space Heat Type
0 Electric resistance 0 All other (see over for definitions)
Glazing Area Calculation
Note: Below grade walls may be included in the
Gross Exterior Wall Area if they are insulated to
the level required for opaque walls.
Total Glazing Area Electronic version: these values are automatically taken from ENV -UA -1.
(rough opening) Gross Exterior
(vertical & overhd) divided by Wall Area times 100 equals % Glazing
24.0 - 766.0 X 100 = 3.1%
Concrete/Masonry Option
0 yes Check here if using this option and if project meets all requirements for the Concrete/Masonry
no Option. See Decision Flowchart (over) for qualifications. Enter requirements for each qualifying
assembly below.
O yes Check here if using semi - heated path and if project meets all requirements for semi- heated spaces
Semi- Heated Path no as defined in section 1310. Requires other fuel heating and qualifying thermostat Only wall
insulation requirement is reduced (2006 change). Only available in prescriptive path.
2006 Washington State Nonresidential Energy Code Compliance Form
E,n;velope Summary
Climate Zone 1
ENV -SUM
2006 Washington State Nonresidential Energy Code Compliance Forms
Project Description
1 17 New Building ❑ Addition
1. Assemblies with metal framing must comply with overall U- factors
Notes:
Alteration ❑ Change of Use
Revised July 2007
Compliance Option
❑ Prescriptive 0 Component Performance
(See Decision Flowchart (over) for qualifications)
❑ Seattle EnvStd
❑ Systems Analysis
toB oy�
I.
JAN 29 2008
i ;;t_NTEFt
E',nvelope Summary (back) Climate Zone 1
ENV -SUM
2006 Washington State Nonresidential Energy Code Compliance Forms
Decision flowchart
for Prescriptive Option
Use this flowchart to determine if project qualifies for the optional Prescriptive Option.
If not, either the Component Performance or Systems Analysis Options must be used.
1302 Space Heat Type: For the purpose of determining building envelope
requirements, the following two categones comprise all space heating types:
Other: All other space heating systems including gas, solid fuel, oil, and
propane space heating systems and those systems listed in the exception to
electric resistance. (continued at right)
—N
Assembly Description
All Insulation Installed?
Below Grd Wall (ext) R -10
Below Grd Wall (oth) R -19
Roof Over Attic R -30
All Other Roof R -21
Raised Floor R -19
Slab -On -Grade R -10
Radiant Floor R -10
Opaque Door U -0.60
No
Mass Wall
Criteria OK?
(below)
Yes
AG Mass Wall Insulation Req.
Mass Wall U0.15/R5.7ci
CMU Block Ins. Cores
Wood Frame R19
Metal Framed R19
No
Concrete/Masonry Option
2006 Washington State Nonresidential Energy Code Compliance Form
LYes-
Above Grade
Wall R19
res
No
Yes
Glazing Criteria Met?
Glazing Vert OH
Area % UVaI UVal SHGC
0-30% 0.55 0.70 0.45
30-45% 0.45 0.80 0.40
>45% Not Allowed
Yes
No
•
Assy.Tag
Prescriptive
Path Allowed
Component Performance,
Systems Analysis, or
EnvStd Required
HC**
Electric Resistance: Space heating systems which use electric resistance
elements as the pnmary heating system including baseboard, radiant, and
forced air units where the total electric resistance heat capacity exceeds 1.0
Wi1t of the gross conditioned floor area. Exception: Heat pumps and
terminal electric resistance heating in variable air volume distribution systems.
Yes
Yes
Glazing Criteria Met?
Yes—
Glazing Vert OH
Area % UVal UVaI SHGC
0-30% 0.40 0.60 0.40
>30 Not Allowed
Yes
fJ
No
Wall Heat Capacity (HC)
Totals
Area (sf)
No-
Area weighted HC: divide total of (HC x area) by Total Area
All Insulation Installed?
Wood Metal
Below Grd Wall (ext) R -10 R -10
Below Grd Wall (oth) R -19 U -0.062
Roof Over Attic R -38 U -0.031
All Other Roof R -30 U -0.034
Raised Floor R -30 U -0.029
Slab -On -Grade R -10 R -10
Radiant Floor R -10 R -10
0. - . ue Door U -0.60 U-0 60
Ye No
Yes
•
AG Mass Wall Insulation Req.
Mass Wall U0.15/R5.7ci
CMU Block Ins. Cores
Wood Frame R19
Metal Framed U0.062
No
V
HC x Area
Revised July 2007
N••
*If the area
weighted heat
capacity (HC) of
the total above
grade wall is a
minimum of 9.0,
the Concrete
Masonry Option
may be used.
'*For framed
walls, assume
HC =1.0 unless
calculations are
provided; for all
other walls, use
Section 1009.
Project
Address WWI LA kx)OB RCE )PARR
Date 1/24/2008
Space Heat Type
Q Electric resistance QQ All other
3.1% Prop. 1 Max.Target
For Building Department Use
Glazing Area as % gross exterior wall area
Concrete/Masonry Option
0 Yes Q No
Notes: If glazing area exceeds maximum allowed in Table, then calculate adjusted areas on back (over).
Building Component
List components by assembly ID & page #
Proposed UA
U- factor x Area (A) = UA (U x A)
Target UA
U- factor x Area (A) = UA (U x A)
Vertical
Glazing
U= 0.550 Plan ID T -
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
0.550 24.0 13.2
0.550 24.0 13.2
Glazing % Electric Resist. Other Heating
0-30% 0.40 0.55
>30 -45% see note above 0.45
Overhead Glazing
Over Attics
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
0.700
Glazing % Electric Resist. Other Heating
0-30% 0.6 0.7
>30 -45% see note above 0.6
Oth.Roofs
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
0.700
Opaque l
Doors
U= 0.600 Plan ID T -
U= Plan ID:
U = Plan ID:
0.600 42.0 25.2
0.600 42.0 25.2
Electric Resist Other Heating
0.60 0.60
"!wv
JOAO
InM.1
R = Plan ID:
R= Plan ID:
R= Plan ID:
0.036
Electric Resist. Other Heating
0.031 0.036
Other
Roofs
R= 30.0 Plan ID T -
R= Plan ID:
R= Plan ID:
0.033 250.0 8.3
0.046 250.0 11.5
Electric Resist. Other Heating
0.034 0.046
Opaque Walls*
R =19.0 Plan ID T -1
R =19.0 Plan ID T - 1
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
"Note: sum of Target Areas here should equal
0.091 450.0 41.0
0.096 250.0 24.0
Target Opaque Wall Area (see back)
0.109 700.0 76.3
**
Electric Resist. Other Heating
Frame -Wd 0.062 0.062
Frame -Mtl 0.062 0.109
Mass Wall 0.15 0.15
++ see mass wall Criteria
epeJO
MMAO
R= Plan ID:
R= Plan ID:
R= Plan ID:
Note: if insulated to levels required for opaque
walls, list above with opaque walls
Electric Resist. Other Heating
Int Ins 0.062 0.082
Ext Ins 0.07 0.07
Nuv.ru! !
JOAO
C Innl J
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
0.056
Electric Resist. Other Heating
0.029 0.056
o1GU-U11-
grade
Pariianf
R= 1.4 Plan ID T - 1
R= Plan ID:
R= Plan ID:
R= Plan ID:
0.730 70.0 51.1
0.540 70.0 37.8
Electric Resist. Other Heating
F =0.54 F =0.54
(see Table 13-1 for radiant floor v alues)
For CMU walls, indicate core insulation material. Totals
r
1086.0
162.7
Totals
1086.0
164.0
2006 Washington State Nonresidential Energy Code Compliance Form
nv,elope
alculations
Climate Zone
NV JA
• 2006 Washington State Nonresidential Energy Code Compliance Forms
Revised July 2007
To comply:
1) Proposed Total UA shall not exceed Target Total UA.
2) Proposed Total Area shall equal Target Total Area.
OG=
00=
Target SHGC
SHGC x Area A) = SHGC x A
VG=
24.0
0.450 24.0 10.8
0.450 24.0 10.8
250.0
*Note: Manufacturer's SC may be used in lieu of SHGC.
Totals
700.0
Glazing
List com • onents b assembl ID & • a • e #
Proposed SHGC
SHGC* x Area A = SHGC x A
Target SHGC
SHGC x Area A) = SHGC x A
6uizelo
ID:
ID:
ID:
ID:
ID:
ID:
0.450 24.0 10.8
0.450 24.0 10.8
Glazing % Electric Resist. Other Heating
0-30% 0.4 0.45
>30 -45% not allowed 0.4
*Note: Manufacturer's SC may be used in lieu of SHGC.
Totals
24.0
10.8
Totals
24.0
10.8
- 2006 Washington State Nonresidential Energy Code Compliance Forms
Glazing Area
Opaque Area
Gross Exterior Wall
Area
344.7
Roofs over Attics
Other Roofs
(
Walls'
2006 Washington State Nonresidential Energy Code Compliance Form
Climate Zone 1 ENV -SHGC
For compliance: Proposed total SHGC x A shall not exceed Target total SHGC x A
NOTE: Since 1997 SHGC compliance for vertical and overhead glazing is allowed to be calculated together.
Target Area Adjustment Calculations
If the total amount of glazing area as a % of gross exterior wall area (calculated on ENV -SUM1) exceeds the maximum allowed in Table 13 -1,
then this calculation must be submitted Use the resulting areas In the Target UA and SHGC calculations above.
Proposed Areas: Numbered values are used in calculations below.
Roofs over Attics Other Roofs Walls
Max Glazing Area
(Table 13 -1)
766.0 I X I 45.0% I _ I 100 I= 1 344.7
Target OG Area in Roofs over Attics
0 lesser
344.7
Proposed Opaque Area
+
250.0
Proposed Opaque Area
700.0
Max OG Remaining
344.7
Proposed VG Area
Maximum Target
Glazing Area
Target OG Area in Other Roofs
a lesser
344.7
Proposed OG Area y Target OG Area`►'
Target VG Area
+ ( 24.0 24.0
Target VG Area
(
24.0
Target Opaque Area
250,0
Target Opaque Area
(
700.0
Note: If there is more than one type of wall, the Target VG Area may be distributed among them, and separate Target Opaque Areas found.
If the Target Areas for Opaque Walls listed on the front must equal the total calculated here.
Revised July 2017
Note:
OG = overhead glazing
VG = vertical glazing
For Target OG's, the
lesser values are
used both here and
below.
I Target Areas OK I
Target values in shaded boxes are used in the applicable Target UA calculations on the front.
Target VG Area and Total Target OG Area are also used in the applicable Target SHGC calculations above.
Building Permit
2006 Washington State Nonresidential
Plans checklist ENV -C,HK
Energy Code Compliance Forms Revised July 2007
Project Address TtlravzrA coar4ERCE PARK
!Date 1/24/2008
The following information is necessary to check a building permit application for compliance with the building envelope requirements in
the Washington State Nonresidential Energy Code.
Applicability
(yes, no, n.a.)
Code
Section
I Component
(
Information Required
Location
on Plans
I Building Department
Notes
GENERAL REQUIREMENTS (Sections 1301 -1314)
1301
Soo. -
Unconditioned s • . ces identified on . fans if allowed
1302
Space heat type:
If "Other",
indicate on plans that electric resistance heat is not allowed
1310.2
Semi- heated spaces
Semi- heated spaces identified on plans if allowed
1311
Insulation
1311.1
Insul. installation
Indicate densities and clearances
1311.2
Roof /ceiling insul.
Indicate R -value on roof sections for attics and other roofs;
Indicate clearances for attic insulation;
Indicate baffles if eave vents installed:
Indicate face stapling of faced batts
1311.3
Wall insulation
Indicate R -value on wall sections;
Indicate face stapling of faced batts;
Indicate above grade exterior insulation is protected:
Indicate loose -fill core insulation for masonry walls as necess;
Indicate heat capacity of masonry walls
if masonry option is used F73;
1311.4
Floor insulation
Indicate R -value on floor sections;
Indicate substantial contact with surface;
Indicate supports not more than 24" o.c.;
Indicate that insulation does not block
airflow through foundation vents
1311.5
Slab -on -grade floor
Indicate R -value on wall section or foundation detail;
Indicate slab insulation extends down vertically 24" from top;
Indicate above grade exterior insulation is protected
1311.6
Radiant floor
Indicate R -value on wall section or foundation detail;
Indicate slab insulation extends down vertically 36" from the top;
Indicate above grade exterior insulation is protected;
Indicate insulation also under entire slab where req'd. by Official
1312
Glazing and doors
Provide calculation of glazing area (including both vertical
vertical and overhead) as percent of gross wall area
1312.1
U -factors
Indicate glazing and door U- factors on glazing and door
schedule (provide area - weighted calculations as necessary);
Indicate if values are NFRC or default, if values are default
then specify frame type, glazing layers, gapwidth, low-e
coatings, gas fillings
1312.2
SHGC & SC
Indicate glazing solar heat gain coefficient or shading
coefficient on glazing schedule (provide area - weighted
calculations as necessary)
1313
Moisture control
1313.1
Vapor retarders '
Indicate vapor retarders on warm side
1313.2
Roof /ceiling vap.ret
Indicate vapor retarder on roof section;
Indicate vap. retard. with sealed seams for non -wood struc.
1313.3
Wall vapor retarder
Indicate vapor retarder on wall section
1313.4
Floor vapor retarder
Indicate vapor retarder on floor section
1313.5
Crawl space vap. ret.
Indicate six mil black polyethylene overlapped 12" on ground
1314
Air leakage
1314.1
Bldg. envel. sealing
Indicate sealing, caulking, gasketing, and weatherstripping
1314.2
Glazing/door sealing
Indicate weatherstripping
1314.3
Assemb. as ducts
Indicate sealing, caulking and gasketing
1314.4 Recessed Lighting Fixtun
Indicate IC rating, ASTM E283 certification, and gasketing or caulking to
ceiling
PRESCRIPTIVE/COMPONENT PERFORMANCE (Sections 1320 -23 or 1330 -34)
Envelope Sum. Form
Completed and attached.
Provide component performance worksheet if necessary
If "no" is shown for any question, provide explanation:
2006 Washington State Nonresidential Energy Code Compliance Form
2006 Washin ton State Nonresidential Ener Code Corn • Hance Form
Building
•
Permit Plans Checklist
•
ENV -CHK
2006 Washington State Nonresidential Energy Code Compliance Fors
Revised July 2007
Envelope - General Requirement
1311 Insulation
1311.1 Installation Requirements: All insulation materials
shall be installed according to the manufacturers
instructions to achieve proper densities, maintain clearances
and maintain uniform R- values. To the maximum extent
possible, insulation shall extend over the full component
area to the intended R- value.
1311.2 Roof /Ceiling Insulation: Open -blown or poured
loose -fill insulation may be used in attic spaces where the
slope of the ceiling is not more than 3/12 and there is at
least 30 inches of clear distance from the top of the bottom
chord of the truss or ceiling joist to the underside of the
sheathing at the roof ridge. When eave vents are installed,
baffling of the vent openings shall be provided so as to
deflect the incoming air above the surface of the insulation.
Where lighting fixtures are recessed into a suspended or
exposed grid ceiling, the roof /ceiling assembly shall be
insulated in a location other than directly on the suspended
ceiling.
EXCEPTION: Type IC rated recessed lighting fixtures.
Where installed in wood framing, faced batt insulation
shall be face stapled.
1311.3 Wall Insulation: Exterior wall cavities isolated
during framing shall be fully insulated to the levels of the
surrounding walls. When installed in wood framing, faced
batt insulation shall be face stapled.
Above grade exterior insulation shall be protected.
1311.4 Floor Insulation: Floor insulation shall be installed
in a permanent manner in substantial contact with the
surface being insulated. Insulation supports shall be
installed so spacing is not more than 24 inches on center.
Installed insulation shall not block the airflow through
foundation vents.
1311.5 Slab -On -Grade Floor: Slab -on -grade insulation
installed inside the foundation wall shall extend downward
from the top of the stab a minimum distance of 24 inches or
to the top of the footing, whichever is less. Insulation
installed outside the foundation shall extend downward a
minimum of 24 inches or to the frost line, whichever is
greater. Above grade insulation shall be protected.
EXCEPTION: For monolithic slabs, the insulation shall
extend downward from the top of the slab to the bottom of the
footing.
1311.6 Radiant Floors (on or below grade): Slab -on-
grade insulation shall extend downward from the top of the
slab a minimum distance of 36 inches or downward to the
top of the footing and horizontal for an aggregate of not less
than 36 inches.
If required by the building official where soil conditions
warrant such insulation, the entire area of a radiant floor
shall be thermally isolated from the soil. Where a soil gas
control system is provided below the radiant floor, which
results in increased convective flow below the radiant floor,
the radiant floor shall be thermally isolated from the sub -
floor gravel layer.
1312 Glazing and Doors
1312.1 Standard Procedure for Determination of Glazing
and Door U- Factors: U- factors for glazing and doors shall
be determined, certified and labeled in accordance with
Standard RS -31 by a certified independent agency licensed
by the National Fenestration Rating Council (NFRC).
Compliance shall be based on the Residential or the
Nonresidential Model Size. Product samples used for U-
factor determinations shall be production line units or
representative of units as purchased by the consumer or
contractor. Unlabeled glazing and doors shall be assigned
the default U- factor in Table 10-6.
1312.2 Solar Heat Gain Coefficient and Shading
Coefficient: Solar Heat Gain Coefficient (SHGC), shall be
determined, certified and labeled in accordance with the
National Fenestration Rating Council (NFRC) Standard by a
certified, independent agency, licensed by the NFRC.
EXCEPTION: Shading coefficients (SC) shall be an
acceptable alternate for compliance with solar heat gain
coefficient requirements. Shading coefficients for glazing
shall be taken from Chapter 31 of Standard RS -1 or from the
manufacturer's test data.
1313 Moisture Control
1313.1 Vapor Retarders: Vapor retarders shall be installed
on the warm side (in winter) of insulation as required by this
section.
EXCEPTION: Vapor retarder installed with not more than 1/3
of the nominal R -value between it and the conditioned space.
1313.2 Roof /Ceiling Assemblies: Roof /ceiling assemblies
where the ventilation space above the insulation is less than an
average of 12 inches shall be provided with a vapor retarder.
(For enclosed attics and enclosed rafter spaces, see Section
1203.2 of the International Building Code.) Roof /ceiling
assemblies without a vented airspace, allowed only where
neither the roof deck nor the roof structure are made of wood,
shall provide a continuous vapor retarder with taped seams.
EXCEPTION: Vapor retarders need not be provided where all
of the insulation is installed between the roof membrane and the
structural roof deck.
1313.3 Walls: Walls separating conditioned space from
unconditioned space shall be provided with a vapor retarder.
1313.4 Floors: Floors separating conditioned space from
unconditioned space shall be provided with a vapor retarder.
1313.5 Crawlspaces: A ground cover of six mil (0.006 inch
thick) black polyethylene or approved equal shall be laid over
the ground within crawlspaces. The ground cover shall be
overlapped 12 inches minimum at the joints and shall extend to
the foundation wall.
EXCEPTION: The ground cover may be omitted in crawl
spaces if the crawtspace has a concrete slab floor with a
minimum thickness of 3 -1/2 inches.
1314 Air Leakage
1314.1 Building Envelope: The requirements of this section
shall apply to building elements separating conditioned from
unconditioned spaces. Exterior joints around windows and
door frames, openings between walls and foundation, between
walls and roof and wall panels; openings at penetrations of
utility services through walls, floors and roofs; and all other
openings in the building envelope shall be sealed, caulked,
gasketed or weatherstripped to limit air leakage.
1314.2 Glazing and Doors: Doors and operable glazing
separating conditioned from unconditioned space shall be
weatherstripped. Fixed windows shall be tight fitting with glass
retained by stops with sealant or caulking all around.
EXCEPTION: Openings that are required to be fire resistant.
1314.3 Building Assemblies Used as Ducts or Plenums:
Building assemblies used as ducts or plenums shall be sealed,
caulked and gasketed to limit air leakage.
1314.4 Recessed Lighting Fixtures: When installed in the
building envelope, recessed lighting fixtures shall by Type IC
rated, and certified under ASTM E283 to have no more than
2.0 cfm air movement from the conditioned space to the ceiling
cavity. The lighting fixture shall be tested at 75 Pascals or 1.57
Ibs pressure difference and have a label attached, showing
compliance with this test method. Recessed lighting fixtures
shall be installed with a gasket or caulk between the fixture and
ceiling to prevent air leakage.
ACTIVITY NUMBER: D08 -044
PROJECT NAME: GE
SITE ADDRESS: 12600 INTERURBAN AV S
X Original Plan Submittal
Response to Correction Letter #
DEPARTMENTS:
ng Division
P bli Works a
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
Complete
Comments:
Permit Center Use Only
INCOMPLETE LETTER MAILED:
Departments determined incomplete: Bldg ❑
TUES/THURS R UTING:
Please Route Structural Review Required
REVIEWER'S INITIALS:
APPROVALS OR CORRECTIONS:
Approved
Notation:
REVIEWER'S INITIALS:
Documents/routing slip.doc
2 -28 -02
�ERINIT COORD COPY •
PLAN REVIEW /ROUTING SLIP
Structural
Incomplete
Approved with Conditions
61.- 40( I -31-o'
Fire Prevention
Fire ❑ Ping ❑ PW ❑ Staff Initials:
LETTER OF COMPLETENESS MAILED:
Revision #
DATE: 01 -29 -08
Response to Incomplete Letter #
X41.0
PI rining Division
Permit Coordinator
DUE DATE: 01 -31 -08
Not Applicable
No further Review Required
DATE:
After Permit Issued
DUE DATE: 02 -28 -08
Not Approved (attach comments)
DATE:
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections:
Bldg ❑ Fire ❑ Ping ❑ PW ❑
Staff Initials:
License Information
License
PRECIBI151C2
Licensee Name
PRECISION BUILDERS INC
Licensee Type
CONSTRUCTION CONTRACTOR
UBI
600553713
Ind. Ins. Account Id
Business Type
CORPORATION
Address 1
PO BOX 98609
Address 2
City
DES MOINES
County
KING
State
WA
Zip
981980609
Phone
2068782948
Status
ACTIVE
Specialty 1
GENERAL
Specialty 2
UNUSED
Effective Date
2/22 /1985
Expiration Date
1/19/2010
Suspend Date
Separation Date
Parent Company
Previous License
PRECIB *163BR
Next License
WE
Associated License
Business Owner Information
Name
Role
Effective Date
Expiration Date
SANBURN, SCOT D
AGENT
02/22/1985
Look Up a Contractor, Election or Plumber License Detail
Washington State Department of Labor and Industries
General /Specialty Contractor
A business registered as a construction contractor with L &I to perform
construction work within the scope of its specialty. A General or Specialty
construction Contractor must maintain a surety bond or assignment of
account and carry general liability insurance.
DEVELOPERS
SURETY &
•
Bond Information
Bond Bond
Company Account Effective Expiration Cancel Impaired Bond Received
Bond Name Number Date Date Date Date Amount Date
#4
DEVELOPERS
INS CO
415171C
01/19/2002
Until
Cancelled
$12,000.00
01/14/2002
Page 1 of 3
https: // fortress. wa. gov /lni/bbip /printer.aspx ?License= PRECIBI151 C2 02/19/2008
TRUE NORTH
N.T.S.
TENANT SPACE
UNDER THIS PERMIT
SIDE PLAN
L
TRUE NORTH
4.
No changes s ; .auF I33 .:a to the scope
of work v.itli ; ;wa y; Jprova; of
Tukwila Bus.din is ivisior .
NOTE: Revisions Mil require a new plan submittal
and may include additional plan review fees.
NORTH
1
VICINITY MAP
N.T.S.
PROJECT AND 'BUILDING DATA
BUILDING CODE: 2006 IBC WITH WASHINGTON
WI STATE AMENDMENTS
LOCATION:
PARCEL NUMBER: 0004800003
ACCOUNT NUMBER : 000480000306
SEPARATE PERMIT
REQUIRED FOR:
'Mechanical
Electrical
�* lumbing
WU Gas Piping
City of Tukwila
BUILDING DIVISION
TUKWILA COMMERCE PARK, BUILDING A
12600 INTERURBAN AVE. S., SUITE 110
TUKWILA, WA
CONSTRUCTION TYPE: V -B SPRINKLERED
OCCUPANCY GROUP(9): GROUP B OFFICE
ZONE: C / L -1
LOT AREA: 465,295 SQ Ft (10.68 ACRES)
TENANT SUITE AREA:
OFFICE: 250 SF.
WAREHOUSE: 3,209 SF.
TOTAL: 3,459 S.F.
PARKING: NO CHANGE
SCOPE:
CONSTRUCT NEW OFFICE FOR TENANT TO INCLUDE NON-
BEARING WALLS AND SUSP. ACOUSTICAL CEILING.
ENVELOPE:
NEW OFFICE AREA TO HAVE WALLS INSULATED W/ R -19 BATT
E CEILING INSULATED W/ R -30 BATT INSULATION.
LEGAL DESCRI 'TION
LEWIS C C -D C ' 31 BEG N 81 -44 -15 E 19911 FT FROM HUB AT END OF
CURVE ON CENT LN OF DUWAMISH- RENTON JUNCTION RD SD NUB BEING
APPROX 1200 FT N AND 440 FT W OF 1/4 COR BET SECS 14 4 15 -23 -4 TN
N 49 -24 -00 W 2535 FT TH N 09 -36 -00 E 52 FT TO TRUE BEG TN S
82 -40 -30 E 590 FT TI-IN 59 -22 -30 E 64335 FT tH N 01 -51 -30 W 343 FT
TO LEFT BANK OF DUWAMISH RIVER BEING NLY BOUNDRY OF LEWIS D
C TN SWLY ALG SD B4N( OF RIVER TO PT N 00 -39 -40 W OF TRUE BEG
TN 5 00 -39 -40 E TO TRUE BEG ALSO FOR OFD C LY W OF ABOVE
DESCRIBED LAND SLY 16.15 FT AND A 16 FT STRIP ADJ AND PARL TO
ELY LNOFR/ WOFPSELEC FOR JOINT RDTGW LOT 41OFPLAT
OF RIVERSIDE INTERURBAN TRS
FILE COPY
Permit No.
Plar review approval Is Ito snore and omissions.
Approval of construcllon documents does not authorize
the violation of any adopted code or ordinance. Feceipt
of approved and Is wed:
City of Tukwila
BUILDING DIVISION
008' OMLJ
T
JAN 2 9 2008
..; imo CENTER
W
O
0
csi
W
0
4
0
w
2
0
a
c0 (D
00
N N
w
z
0 X
�
Z co
( F--
w 0
>Z
E T-
0 cn
z w
OJ
m1 co
H
Q
0 W
�(/)
0
P ai
II
T -0
\ \Wkst - \Documents \CAD12002 \0 RREEFI Tenant Improvements\Tukwila Commerce Park\BLDG A \GE \SITE PLAN.dwg, T -0, 1/29/2008 9:11:14 AM
ROOM SCHEDULE
A
B
ROOM 't - FLOOR NEW CARPET
BASE: NEW 4" RUBBER BASE
WALL: GYP. BD. (PAINTED) (EE)
CEILING: SUSPENDED ACOUSTICAL ( +9'AFF)
WALL TYPES
. EXISTING CONCRETE WALL FURRED W/ 5/8" GYP. BD. OVER STEEL STUDS g 24" O:C.
4 R -19 BATT INSULATION. U =0.096
LEGEND
$3
6" X 20 GA STEEL STUDS +9 24" O.G. W R" GYB. BD. BOTH SIDES TO 10' AFF., PROVIDE DIAGONAL
STEEL STUD BRACE TO ROOF DECK s a O.C. BEE DETAILS. BATT INSULATION. U =0.091
DUPLEX OUTLET
A WALL TELEPHONE OUTLET AND DATA, MUDRING, CONDUIT AND PULL STRING
ONLY.
3 POLE LIGHT SWITCH
RECESSED 2X4 -2 TUBE, T -8 FLUORESCENT 66 WATTS LIGHT FIXTURE
FIXTURE W/ PARABOLIC LENSE. TOTAL PROPOSED WATTAGE
TOTAL ALLOWABLE WATTAGE = 1 WATT / SF. X 250 F. = 250 WATTS
DOOR SCHEDULE (LEVER HANDLES)
DOOR Ei : EXISTING 3'4" X,' -0" HOLLOW METAL DOOR NO CHANGE
DOOR E2 : EXISTING OVERHEAD DOOR, NO CHANGE
DOOR E3: EXISTING 3' X 1' S.C. WOOD DOOR, METAL JAMB, I-1/2 PAIR BUTTS,
PRIVACY LOCK, WALL STOP, CLOSER
DOORS 1 4 2: 3' X 1' S.C. WOOD DOOR, METAL JAMB , I -1/2 PAIR BUTTS,
WALL STOP, LOCKSET, WEATHERSTRIPPING, THRESHOLD
Suspended Ceilings Notes
Suspended ceilings are tm comply with the following codes and regulations
1.2006 International Building Code (IBC) Sections 803.9 and 162.1
2. AWN 0635 and ASTM ;436 (referenced in IBC 803.9). ASTM is an acronym for
American Society for Testing and Materials_
3. ASCE -1 Section 9.62b (referenced in IBC 1621.12). ASCE is an a cronym for American
Society of Civil Engineers.
4. C15CA recommendations for seismic Zones 3 -4 (referenced in ASCE -1 Section
9.62622). CISCA is an acronym for Ceilings 4 Interior Systems Construction Association.
5. IBC 102.1 states, "Where, in any specific case, different sections of this code specify
different materials, methods of construction or other requirements, the most restrictive
shall govern. Where there is a conflict between a general requirement and a specific
requirement, the specific requirement shall be applicable"
6. Partial 1lsting of requirements for suspended ceilings:
a. Only a heavy duty T -bar grid system shall be used. ASCE - Section 9.2.22 item a.
b. Width of the perimeter supporting closure angle (wall angle) shall be not less than 2.0
inches. ASCE -1 Section 962.622 item b.
c. On two adjacent sides, the grid shall be attached to the wall angle. Pop rivets are
acceptable. On the other two sides, the shall be a / inch clearance between the ends
of the grid and the wall. ASCE -1 Section 962.622 item b.
d. Stabilizer bars are required to prevent the spread of main beams and /or cross
tees. CISCA Guidelines For Seismic Restraint For Direct Hung Suspended Ceiling
Assemblies, Seismic Zones 3 4 4, May 2004, Installation Section, Item 4.
e. Perimeter support (tail) wires are required within eight inches of the wall for all
edges. CISCA Guidelines for Seismic Restraint for Direct Hung Suspended Ceiling
Assemblies. Seismic Design Groups D/3 4 E/4, May 2004, Installation Section, item 2.
f. vertical hangers shall be No.12 gage wire spaced at 4 feet on center. Three wire
turns required Within 1:6 out -of -plumb unless counter - sloping wires are provided.
g. Lateral bracing Is required: splay wire pods at 12 max oc. and 6 max. From walls.
CISCA Guidelines for Seismic Restraint for Direct Hung Suspended Ceiling Assemblies,
Seismic Design Groups D/3 4 E /4, May, 2004, Installation Section, item 3, ASCE1 -02,
962622, and City of Kent Policy require lateral bracing at all ceiling areas greater
then 144 5F surrounded by walls that connect directly to structure above.
h. Ceilings over 2500 square feet must have seismic separation Joints or MI height
partition that breaks the ceiling up into areas not exceeding 2500 square feet.
ASCE -1 Section 962b22 item d.
1. For ceilings without rigid bracing, spr(ricler head and other penetrations shall have a
2 -inch in all horizontal drrectionst or, sprinkler head extension to have a swing Joint
that can accommodate 1 inch of ceiling movement in all horizontal directions_ ASGE -1
Section 9.6.2.622 item e.
J. Changes In ceiling plan elevation shall be provided with positive bracing. ASCE -1
Section 9 62.22 Item f.
k. Cable trays and electrical conduits shall be supported independently of the ceiling.
ASCE -1 Section 9.621222 item g.
GENERAL NOTES
1 NEW OFFICE AREA TO BE PROVIDE WiTH FULL HVAC.
2. PATCH, REPAIR, 4 PAINT EXTERIOR WALLS 4 DOORS.
3. PROVIDE 30 AMP, 208\' FORK LiFT CI4AR 11%* STATION OUTLET.
4. REFURBISH EXISTING RESTRDOM, PATCH, REPAIR, 4 PANT GYP.
BD. WALLS 4 CEILING, NSTALL NEW TOILET, SINK P. LAM.
WAINSCOT, SHEET VINYL FLOORING, 4 COVED SWEET BASE.
5. CLEAN 4 SEAL CONCRETE FLOOR IN U1AREI- IOUSE.
6. INSTALL NEW T -8 FLUORESCENT LIGHT FIXTURES THROUGHOUT
WAREHOUSE, MAX 05 WATTS / SF.
1. RELOCATE EXISTING UNIT HEATERS, REPLACE UNITS AS REQUIRED.
MAX 8 BTU / HR FOR FREEZE PROTECTION.
STEEL STUD BRACE e
8' -0 "0 .C. TO
ROOF PURLIN -
ATTACH TO TOP OF
WALL AND PURLIN
APO BAIT INSULATION
SUSPENDED ACOUSTICAL CEILING
.,� 10' -0'I
IS BATT INSULATION
4I W.
' S
STUDS a 24" O.G.
5/8" GYP. BD.
GA.
INTERIOR WALL MEAD DETAIL
SCALE:1 1/2" : 1' -0"
6 "X'20 GA. STEEL
STUDS a 24" O.G.
6 "X20 GA. STEEL TRACK
ATTACH BOTTOM
TRACK TO CONC.
FLOOR W/ POWDER
DRIVEN ANCHORS
AT 24" O.C.
4
•
5/8" GYP. 8D.
INTERIOR WALL SiLL DETAIL
EXiST. CONC. SLAB ON GRADE
0
NORTH
FLUSH OVERLAY
PLAM. DRAWERS
W/ METAL SLIDES
4 WIRE PULLS
4" TOE KiCK
1' -2
)1/
,11 - 111 1_
/ ih YJ
4.
X
X X
REFLECTED CEILING PLAN
1/8 " =1' —
1 -0
2' -0" O.C.
2'
40
25' - 0"
121 ;' -/JI1: 61-8" 1_0I
2'X4' SUSPENDED ACOUSTICAL
9' - AFF., SEE= SEISMIC NOTES.
EX. WAREHOUSE
NO CHANGE TO ENVELOPE
& NEW LIGHTING NOT TO
EXCEED 0.5 WATTS / S.F.
40'-0"
2-COMPARTMENT SINK
W/ LEVER HANDLE SW
� CABINET ELEVATION
1'_
2' -0" O.C.
n
3'
0
OPEN
1 ' -
2'
0
FLUSH OVERLAY P. LAM.
FACED UPPER CABINETS
WIRE PULLS
P. LAM BACK SPLASH
FLUSH OVERLAY
FLAK
W/ WIRE PULLS
9
01
NORTH
1' -2"
41-1" 21_0'
40 -0"
25'_0"
12' -6" )' -0 6
II►
B
11)
1p
II) ''
11' -0"
EXISTING DEMISING WALL
FLOOR PLAN
1/8 " =1' -0"
NEW OFFICE
11 1250 S.F.
OCCUPANT LOAD = 2.50
40'
/ 3 ' - 0 " il' -0" X T -1
EXISTING ADA ACCESSIBLE
RESTROOM W/ GRAB BARS
4 ACCESSIBLE ACCESSORIES
EX. WAREHOUSE
3,209 S.F.
OCCUPANT LOAD = 6.42
EXISTING CONCRETE WALL
EXISTING DEMISING WALL
KEY PLAN
N.T.S.
I_
0
EX.
RR
POq
JAN 2 9 2008
U
w
0
0_
N
N
w
0
>-
d
m
0
w
W
U
w
0
M
CO CO
0 O
N N
\\Wkst -4 \Documents \CAD\200210225 RREEF\ Tenant Improvements\Tukwiia Commerce iPark\BLDG A \GE \GE- TI.dwg, T-1-GE, 1/29/2008 9:09:08 AM
E-,
T -1