HomeMy WebLinkAboutPermit B96-0190 - OLD NAVY - TENANT IMPROVEMENTCity of Tukwila ( C. (206) 431-3670
Community Development / Public Works • 6300 Southcenter Boulevard, Suite 100 • Tukwila, Washington 98188
BUILDING PERMIT
Permit No: B96 -0190
Type: B -BUILD
Category: ACOM
Address: 300 ANDOVER PK W
Location:
Parcel #: 262304 -9119
Zoning: C2
Type Const: II -N
Gas /Elec:
Wetlands:
Water: N/A
Contractor License No.: FISHEDI141PT
Status: ISSUED
Issued: 08/07/1996
Expires: 02/03/1997
Type of Occupancy: STORE
Slopes: N
Sewer: N/A
TENANT OLD NAVY STORE
300 ANDOVER PK W, TUKWILA WA 98188
OWNER SEGALE M A INC
PO BOX 88050, TUKWILA WA 98188
CONTRACTOR FISHER DEVELOPMENT Phone: 415 468 -1717
1485 BAYSHORE BOULEVARD, SAN FRANCISCO, CA 94124
CONTACT JAMES FURRATE Phone: 865 -0450
1035 156 AV NE, BELLEVUE WA 98007
*k k*** k*k kk***** k*** kk* kkk* k** k* k*********** * * * * * * * * * * * * *k** * * * ** * * * * * * * * **
Permit Description:
REMODEL EXISTING SPACE.
SETBACKS
Units: 001 Front: .0 Back :, .0
Buildings: 001 Left: .0 Right: .0
Fire Protection: SPRINKLERED
UBC Edition: 1994.
Valuation: 110,000.00
Total Permit Fee: 1,550.96
* k*'k k******* k** k*************k k****** * * * * * * * * * * * * * * * * * * * * * * * * * * * ** **
A 112
Permft'Cente uthorized Signature Date
F-7-q
I hereby certify that I have read and examined this permit and know the
same to.be true and correct. All provisions of law and ordinances
governing this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate
or cancel the provisions of any other state or local laws regulating
construction . or the performance of work. I am authorized to sign for and
obtain this b i'lding rmit
Signature: Date: 7 - " -I
Print Name: _3i_44q I ), iz4iZ_
Title: .7'lfi�
This permit shall become null and void if the work is not commenced within
180 days from the date of issuance, or if the work is suspended or
abandoned for a period of 180 days from the last inspection.
DEPARTMENT ;�
DATE
L APPROVED`
, R EQUIREMENTS /CO ti =
.i:( Plan Review
Meeting
1
1 " 3 ' g o
-"�p'
INIT:
q it BUILDING -
initial review
-___)Q13
7.- 1(0 _`t& R
CONSULTANT: Date Sent - Date Approved -
Z. (ROUTED)
/" FIRE
'7- 1/0--%
/ h LJ(CI �r;
I "
FIREPROTE Sprinklers Detectors Q WA
FIRE DEPT. LETTER DATED: 7/7 ce , INSPECTOR: [, 0 ,
INIT: � .R--
I l
g PLANNING
• 7 -26
,--7 /? �/� 6
ZONING: -7-1)6._ pAR/LANDUSECONDITIONS? Yes 0 No
hEFERENCEFILENOS.: 9, 9 ( - 0
INIT: k (-)
MINIMUMSETBACKS: N- S- E- W-
PUBLIC
WORKS
-25 �_q,_
- W
r f/ l9G
UTILITYPERMITSREQUIRED? 0Yes cz No
PUBLIC WORKS LETTER DATED:
INIT: 4
K BUILDING -
final review
7- 25 -16,
TYPEOFCONSTRUCTION:
CERT.OFOCCUPANCY?
°Yes 0 No
UBC EDITION (year):
INIT: :,
Ag UILDING
FFICIAL
7 Z5 -9 Co
""),g -`il,
INIT: `6"=
AMOUNT
OWING:
V
(1 !
" �
il C� 16
r
CONTACTED 1
t �
t Z
r n ,
�-�C
((�
�,�
DATE NOTIFIED
-"�p'
(7 V
(� ii
BY:
( /nit.)
-___)Q13
2nd NOTIFICATION
BY:
(Init)
3RD NOTIFICATION
BY:
(init)
PLAN CHECK
NUMBER
Pf1 o - p l Div
CITY OF TUKWILA
Department of Community Development — Permit Center
6300 Southcenter Boulevard - #100, Tukwila, WA 98188
(206) 431 -3670
DEPARTMENTAL REVIEW
"X" in box indicates which departments need to review the project.
REVIEW COMPLETED
F\L0 co u6
Building Permit Application Tracking
PROJECT NAME
OL-b NNy G�g-F
SITE ADDRESS
Soo ANN(>I - Pv_ 2/■1
SUITE NO.
(000
INSTRUCTIONS TO STAFF
• Contacts with applicants or requests for information should be summarized in writing by staff so
that the status of the project may be ascertained at any time.
• Plan corrections shall be completed and approved prior to sending to the next department.
• Any conditions or requirements for the permit shall be noted in the Sierra system or summarized
concisely in the form of a formal letter or memo, which will be attached to the permit.
• Please fill out your section of the tracking chart completely. Where information requested is not
applicable, so note by using "N/A ", date and initial.
02/15/96
OJUU JOUWGunter DOwevara, / uKwna vvH uo IOa
(206) 431 -3670
DESCRIPTION
AMOUNT
RCPT 0
DATE
BUILDING PERMIT FEE
PLAN CHECK FEE `
'7 .
1r1 1 :
`1-1� to
PLAN
NUMBER CHECK ( �J J ` 9(')
6:\
APPLICATION MUST BE
FILLED OUT COMPLETELY
BUILDING SURCHARGE
OTHER.
`: TOTAL -
.: i i W. It
; -:
SITE ADDRESS SUITE #
300 Andover Park West 600
VALUE OF CONSTRUCTION - $
(B) $110,000 (M) $48,000
PROJECT NAME/TENANT
Old Navy Store
ASSESSOR ACCOUNT #
7-6, .Z 30 4 — `� ) 1 9
TYPE OF • New Building • Addition • Tenant Improvement (commercial) • Demolition (building)
WORK: ❑ Rack Storage ❑ Reroof ❑ Remodel (residential) ❑ Other
DESCRIBE WORK TO BE DONE:
Remodel of existing retail tenant space to include arch. & mech. work.
BUILDING USE (office, warehouse, etc.)
Retail sales of clothing RETAIL * * * * **
NATURE OF BUSINESS: Retail sales of clothing
WILL THERE BE A CHANGE IN USE? ❑ No ❑ Yes If Yes, new building requirements may need to be met. Please explain:
SQUARE FOOTAGE - Building: Tenant Space: 1 4, 1 70 Area of Construction: 1 4, 1 7 0
WILL THERE BE STORAGE OR USE OF FLAMMABLE, COMBUSTIBLE OR HAZARDOUS MATERIALS IN THE BUILDING?
❑ No ❑ Yes IF YES, EXPLAIN:
FIRE PROTECTION FEATURES: ❑ Sprinklers ❑ Automatic Fire Alarm System
PROPERTYOWNER Segale Business Park /La Pianta Ltd.
PHONE 206- 575 -2000
ADDRESS Andover Park West #200, Tukwila, WA.
°P98188
CONTRACTOR F Development
PHONE 415- 468 -1717
ADDRESS Bayshore Blvd., San FRancisco, CA. 94124
°P94124
WA. ST. CONTRACTOR'S LICENSE # FISHEDI1 41 PT
EXP. DATE
ARCHITECT H eath Architect
PHONE 510 - 865 -8663
ADDRESS 1115 Atlantic Ave., Ste. 101, Alameda, CA.
ZIP 94501
CITY OF TUKWILA
Department of Community Development - Building Division
•
I HEREBY GEHTIFY;THAT I:FIAVE READ'ANO THIS.APpLCCATIQN KNOW `THE SAME'.
:BE TRUE AND :CORRECT, AND:.I AM: AUTH IZED''TO.' PPLY FOR THIS PERMIT
SIGNATUR
PRINT N E
BUILDING OWNER
OR
AUTHORIZED
AGENT
Jame
ADDRESS 1035 156th Ave.
CONTACT PERSON James Furrate
urrate
JUL 0 1 1996
PERMIT CENTER
BUILDINfl PERMIT
APPLICATION
•
•
DATE J 1 )CR[-)
PHONE 206 -865 -0450
6 -0063
CITY/ZIPBellevue 98007
PHONE 206-865-0450
APPLICATION SUBMITTAL In order to ensure that your application is accepted for plan review, please make sure to fill out the
application completely and follow the plan submittal checklist on the reverse side of this form. Handouts are available at
the Building counter which provide more detailed information on application and plan submittal requirements.
Application and plans must be complete in order to be accepted for plan review.
VALUATION OF CONSTRUCTION Valuation for new construction and additions are calculated by the Department of
Community Development prior to application submittal. Contact the Permit Coordinator at 431 -3670 prior to submitting
application. In all cases, a valuation amount should be entered by the applicant. This figure will be reviewed and is
subject to possible revision by the Building Division to comply with current fee schedules.
BUILDING OWNER / AUTHORIZED AGENT If the applicant is other than the owner, registered architecVengineer, or contractor
licensed by the State of Washington, a notarized letter from the property owner authorizing the agent to submit this
permit application and obtain the permit will be required as part of this submittal.
EXPIRATION OF PLAN REVIEW Applications for which no permit is issued within 180 days following the date of application shall
expire by limitations. The building official may extend the time for action by the applicant for a period not exceeding 180
days upon written request by the applicant as defined in Section 304(d) of the Uniform Building Code (current edition).
No application shall be extended more than once.
If you have any questions about our process or plan submittal requirements, please
contact the Department o cBINtitty Development Building Division at 431 -3670.
CITY
DATE APPLICATION ACCEPTED OFTtJKWILA DATE APPLICATION EXPIRES
10/22/G3
COMMERCIAL
NEW COMMERCIAL BUILDINGS /ADDITIONS
n Completed building permit application (one for each structure
El Assessor Account Number
Two sets (2) of the following:
Specifications
Structural calculations stamped by a Washington State licensed
engineer
Soils report stamped by a Washington State licensed engineer
Topographical survey
n Energy calculations stamped by a Washington :State Licensed
engineer or architect
Legal description
-1 Working drawings, stamped by a Washington State licensed •
architect, which Include:
• Site plan
• Architectural drawings ,.
• Structural drawings
• Mechanical drawings
• Elevations
'• Civil drawigs
• Landscape plan
•
n Completed utility permit application (one for entire project)
Six (6) sets of civil drawings
NOTE: See utility permit application and checklist for specific utility
submittal requirements
Entire spaoe. racks will be located
• Exit doors
• Dimensions of all aisles :
Tenant spac° floor plan showing rack storage layout, aisles and
exits.
I 1
RACK STORAGE
D Completed building permit application •
Assessor Account Number
Two (2) sots'of which include:
Building floor plan showing
I .
NOTE: Include dimensions of racks (height, width and length), aisles
and exit ways on plan
Structural calculations stamped by a Washington State licensed
engineer (rack storage 8' and over)
RESIDENTIAL
NEW SINGLE- FAMILY DWELLINGS /ADDITIONS
n Completed building permit application (one for each structure)
II
Legal description
n Assessor Account Number
Two sets (2) of working drawings,' which incitide:
• Site plan .._._._r (Cm plan, show closest hydrant bcadon.
• Foundation plan include access to building, showing
• Floor plan width and length of access.)
• Roof plan •
• Building 'elevations (all views)
• Building cross - section
• Structural framing plans
n Washington State Energy Code data
II
- Completed utility permit application
n Six (6) sets of site plans showing utilities
NOTE: Building site plan and utility site plan may be combined' See
utility permit application and checklist for specific submittal requirements.
.
Additional topographical and soils information may required if unique
s/to conditions.
SUBMITTAL CHECKLIST
Locati of tenant ape
Existing and proposed parking.::
• Landscape plan (if applicable, •i e , change of use
Overall building plan
• Tenant location
• Use of adjacent (common Wall) tenant
• C±verall dimensions of building or square :foota
Flew; plan of propo tenant spa
• Tenant space plan' withuse o each roam (s helled
:•' doors; ogreae patterns
• • New walls, existing wall, and walls to bedamolished,
Construction details
• Cross sectlons showing wall construction and method of
attachment for floor and ceiling..
Structural calculations stamped by a Washington State licensed
engineer may be required if structural work is to be done (2 sets)
NOTE: If any utility work Is to be done, submit separate udlity permit
application end plans.
REROOF
Completed building permit application (one for each structure)
n Assessor . Account Number
r- Narrative describing existing roof, material being removed, and
material being installed
• NOTE: A certification letter is required prior to final inspection and
• off of the permit.:
ANTENNA/SATELLITE: DISHES
n Assessor Account Number
Two (2) sets of plans, which include;.
n Site Plan (showing building and location of antenna/satellite dish
n Details antenna/satellite dish and method of attachment
n Structural calculations stamped by a Washington State license
engineer may be required
RESIDENTIAL REMODELS
Completed building permit application (one for each structure )
f] Assessor Account Number
n Two ( sets: drawings which include.
Sitp plan
•
•
fioundatkin pir�i�
•: Floorplan
• Roof plan
Building elevations (all wows
Building ,cross- section
• Structural framing plans;
NOTE If any utilitywork is to be done prov►de utility: permit application
and plans must .be. submi
and
I I
Completed building permit application' ., ..
REROOFS
n Completed building permit application (one for each structure
1 1 Assessor Account Number
Narrative describing existing roof, material being removed,
material being installed
NOTE: A certification letter 1s required prior final inspection and sign
• off of the permit.::.
A*** s\* k* 4* t*• A* A *o\4 * *4*•.'. * * *4* * *s4 * * *k. \ *. *** s4s \sk * * *A*JA * * **•A• * * *:
1380 -O c
CITY OF TUKWILA, WA
TRANSMIT
* h*• skk*** 4. A *A * * *: \*'4 * * * * *A * * ** * * *A ** *A * * * s\A * * *kks \ *h *. k.4*•ki,•l• *s\k*s\ie
TRANSMIT Number: 9600438 Amount: 609.21 07/01/96 12 :13
Pc3ment Method: CHECK Notation: FISHER DEVELOP, knit: SMC
Permit Riau B96-0190 Tyne. B-•BUILD BUILDING PERM] :T
Total Fees. 1 ~ 350.`.3ar
This Payment 609.21 Total ALL Pmts,: .60.9.21
Balance: 941.71
*** AA* o4** it•>\****** s4A * *si *h *A* * * *; \•A••A *•hrkAA *.t k* . * * * * *:\ *ck **s\ * *si* * *:k•k \*
Account Code Description Amount
000/922.100 BUILDING - MOMRES 609.21
0874 07/01 9619 TOTAL 609.21
CITY OF Tltl(WILA
Permit No: B96 -0190
Address.: 300 ANDOVER PK W
uite: 600
Tenant: OLD NAVY STORE Status: ISSUED
Type: B -BUILD Applied: 07/01/1996
Parcel #: 262304-9119 Issued 08107/1996
1 996
44.4 444•* 44144 *444•4•4'4444.4444'.4**444k44k 4444444444 44 '•4-.44.44.4 *•4444,4
Permit Condition..:
1. PRIOR TO FINAL SIGN OFF APPLICANT SHALL RETURN METRO SEWER
USE FORM TO PUBLIC WORKS FOR PROCE'S'SING.
2. No changes wi 11 be made to the plans Lunless approved by the
Architect or Engineer, and the Tukwi 1a Bui lding Division.
Plumbing permits shall be obtained through the Seattle-King
County Department of Public.Health. Plumbing will be
inspected by that agency, including a l l gas p i p i n g
(296 - 4722)'.
4. Electrical' permit: shall be obtained through the Was.h1naton
State Division of `Labor and Industries and all electrical
• work will be inspected by that agency' (248-6630).
5. All mechanical work shall be under separate permit issued by
the City Of Tukwila. •
6. All'p,ermits, inspection records, and approved plans shall be
ava.i lable at. the Job s i t e prior to the start of any con-
struction.. These documents are to be maintained and avail-
able until final inspection approval is granted.
7. All structural welding shall be done by W.A.B.O. certified
welders., and special inspected (UBC - Sec. 306(a)5).
8. Bolts installed in concrete shall be special inspected
(UBC - S`ec. 306(a)2)
9. Whe special inspection is required either the owner,
architect or engineer shall notify the Tukwila Building
Divi ion 'of appointment of the inspection agencies prior to
.
the first building inspection. Copies of all special
inspection reports shall be submitted to the Building
Division in a timely manner. Reports shall contain address,
project name, permit number and tape of inspection being •
performed.
10. The special inspector 'shall submit a final signed report
stating whether the work requiring special inspection was,
to the best of the inspector's knowledge, in conformance
with approved. plans and specifications and the applicable
workmanship p r o v i s i o n s of the UBC.
11. Any new ceiling grid and light fixture installation is
required to meet lateral bracing requirements• for Seismic
Zone 3.
12. Partition walls attached to ceiling grid must be laterally
braced if over eight (3) feet in length.
13. Readily accessible access to roof mounted equipment is
required.
14. Any exposed insulations backing material shall have a Flame
Spread Rating of 25 or less, and material shall bear identi-
fication showing the fire performance rating thereof.
15. All construction to be done in conformance with approved
plans and requirements of the Uniform Building Code (1994
Edition) as amended, Uniform Mechanical Code (1994 Edition),
and Washington State Energy Code (1994 E d i t i o n ) .
16. Validity of Permit. The issuance of a permit or approval of
plans, specifications, and computations shall not be con -
strued to be a permit for, or an approval of any violation
of anv of the provisions of the building code or of anv
4:4*. other ordinance of the jurisdiction. No permit presuming to
• give authority to j " v l a to or cancel the provi ns of t h i s
code shall be val i1
17 There shall be no occupancy of the building(v;) until the
final inspection has been completed by the Tukwila Building
Inspector.
13. A CERTIFICATE OF OCCUPANCY WILL BE REQUIRED FOR THIS PERMIT.
:%* **k* *4*doJr:k **0•* **A Ak k:*- a *N*4 *A *•A*A**A*•kA*A *k
CITY OF TUK:WILA, 1►A Ti`r'Ii':"Ml'7'
*k* * *A *Ak* * **A *A * * * *:k* *•kk•. : * *•1. l4* *A*. •k. *k•A * A* **•kh: }*d** 4•*
TRANSMIT dumber: 89600459 Amount: 941. ?5 08.'0 12 :23
Payment Method: CHECK Notation: FISHER DEV Init: I;JP
Permit No: B96-0190 'dyne: B -I3UILD BUILDING PERi4IT
Parcel No: 262304.9119
Site Address: 300 ANDOVER PI( (4
Account Code Description
000 /3:2.100 BUILDING - NOI!RES
000/345.830 PLAN CHECK -- NQNRES
000/386.904 STATE BUILDING SURCHARGE
0
Total Fees: 1.550.96
This Payment 941.75 Total ALL Pmts: 1,550.96
Balance: .00
*•kA **** * * **A*4.** ***4,•k *k* 011 ** * * #1. * *•kA *:4 * *k* * * **•k* **A *A * * *y4•k1•A.A>1*
Amount
328.04
60`_x.21
4.50
1961.' +Q7 /O13 9617 TOTAL 941.75
Project: /`/ ' `
f
Type of inspect _�
Date called:
Address:
Special instructions
Date wanted:
3 Z -S�l i
m
Requester:
Phone No.:
1 INSPECTION RECORD -
Retain a copy with permit !Ono 5/9b
INSPECTION NO. PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 9818
COMMENTS:
II e 4 . ti
el e.; I Ste e
Inspector;
Approved per applicable codes.
Date:
$42.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must
be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection.
Receipt No.:
Date:
(206) 431 - 3670
Corrections required prior to approval.
City of Tukwila
Community Development / Public Works • 6300 Southcenter Boulevard, Suite 100 • Tukwila, Washington 98188
WARNING: IF CONSTRUCTION BEGINS BEFORE APPEAL PERIOD EXPIRES,
APPLICANT IS PROCEEDING AT THEIR OWN RISK.
Parcel No: 262304 -9001 Permit No:
Address: 300 ANDOVER PK W Status:
Suite No: Issued:
Location: 300 ANDOVER PK W #600 SPACE C; OLD NAVY Expires:
Category: NRES
Type: MISCPERM
Zoning: C2
Const Type: Occupancy:
Gas /Elec.: UBC:
Units: 000 Fire Protection:
Setbacks: North:
Water: N/A
Wetlands:
Contractor Licence No:
OCCUPANT OLD NAVY
300 ANDOVER PK W *600, TUKWILA WA 98188
OWNER SEGALE M A INC
PO BOX 88050, TUKWILA WA 98188
CONTACT DANA WARREN
PO BOX 88050, TUKWILA WA 98138
***************************************************** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * **
Permit Description:
INSTALLATION OF ONE PERMANENT 1.5" WATER METER
FOR TENANT SPACE C(SUITE #600, OLD NAVY STORE).
METER BOXES AND ALL WATER PIPING COMPLETED UNDER
SEPARATE PERMIT PW94 -0021.
***************************************************** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * **
Construction Valuation: $ .00
PUBLIC WORKS PERMITS: *(Water Meter Permits Listed Separate) Eng. Appr: JJS
Curb Cut /Access /Sidewalk /CSS: N
Fire Loop Hydrant: N No:
Flood Control Zone: N
Hauling: N Start Time:
Land Altering: N Cut:
Landscape Irrigation: N
Moving Oversized Load: N Start Time:
Sanitary Side Sewer: N No:
Sewer Main Extension: N Private:
Storm Drainage: N
Street Use: N
Water Main Extension: N Private:
********************** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * **
TOTAL DEVELOPMENT PERMIT FEES: $
********** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * **
Permit Center Authorized Signature:__
Signature:
MISCELLANEOUS PERMIT
.0 South: .0 East: .0 West: .0
Sewer: N/A
Slopes: N Streams:
Phone: 206 575 -2000
Size(in): .00
End Time:
Fill:
End Time:
Public:
(206) 431 -3670
MI96 -0006
ISSUED
09/23/1996
03/22/1997
AM14/4 Date : --�����
I hereby certify that I have read and examined this permit and know the same
to be true and correct. All provisions of law and ordinances governing this
work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or
cancel the provision of any other state or local laws regulating construction
or the performance of work. I am authorized to sign for and obtain this
development permit.
Print N ame:__ 14 _La,,L =.ta
This permit shall become null and void if the work is not commenced within
180 days from the date of issuance, or if the work is suspended or abandoned
for a period of 180 days from the last inspection.
`' METER SUPPLEMENT
DEVELOPMENT PERMIT
Permit No: MI96 -0006
Status: ISSUED
Site Address: 300 ANDOVER PK W
Location: 300 ANDOVER PK W #600 SPACE C; OLD NAVY
WATER METER A
TOTAL WATER METER FEES: $629.50
PUBLIC WORKS ENGINEER APPROVAL: JJS
s.
Applied Date: 09/10/1996
Issued Date: 09/23/1996
WATER METER B WATER METER C
Water Meter Type: PERM
Water Meter Size: 1.50 .00 .00
Quantity: 1
Work Order No: 5106E
Connection Fees: $225.00 $.00 $.00
Install Deposit: $350.00 $.00 $.00
Add'1 Install Deposit: $.00 $.00 $.00
Plan Review Fee: $10.00 $.00 $.00
Inspection Fee: $ $.00 $.00
Water Turn On Fee: $25.00 $.00 $.00
Special Assessment: $.00 $.00 $.00
Other Fee: .00 .00 $.00
City of Tukwila
Department of Public Works
NOTIFICATION OF UTILITY PERMIT ACTION
TO: PERMIT CENTER
FROM: PUBLIC WORKS ENGINEERING
DATE: SEPTEMBER 16, 1996
SUBJECT: OLD NAVY
Segale Retail Space C /Permanent Water Meter
300 Andover Park West Suite #600
Project No.: PRE92 -027
Plan Check No.: B96 -0190
Activity No.: MI96 -0006
Contact Person: Mr. Dana Warren
Phone: (206)575 -2000
THE FOLLOWING PUBLIC WORKS PERMITS HAVE BEEN APPROVED FOR
ISSUANCE IN ACCORDANCE WITH THE PLANS APPROVED ON September 16, 1996:
MI96 -0006 Permanent Water Meter(1.5 ") 625,00
Total Fees: $625.00
Two copies of the confirmed Utility Permit Application with a set of plans are attached for inclusion
in the permit file.
JJS /mv
Attachments a/s
C.F.: PW Utilities Inspector (copy of UPA, application and plans)
Development File (copy of UPA, application and plans)
Ross A. Eamst, P. E., Director
PERMIT FEE
John W. Rants, Mayor
6300 Southcenter Boulevard, Suite #100 • Tukwila, Washington 98188 • Phone: (206) 433-0179 • Fax (206) 431
Project Name/Tenant: SEGALE RETAIL
Description of work to be done (2) 1}" WATER METER" INSTALLED IN EXISTING METER BOX1i
Will there be storage of flammable /combustible hazardous material in the building? ❑ yes IN no
Attach list of materials and stora • e location on se •arate 8 1/2 X 11 • a • er indicatin • • uantities & Material Safet Data Sheets
Value of Construction: N/A
Site Address:
300 ANDOVER PARK WEST, TUKWILA, WA
City State/Zip:
98188
Tax Parcel Numbe
2
Property Owner:
LA PIANTA LIMITED PARTNERSHIP
Address:
P.O. BOX 88050
Phone:
(206)575 -2000
Street Address:
P.O. BOX 88050, TUKWILA, WA
98138
City State/Zip:
Fax #:
(206)575 -1837
Contact Person:
MR. DANA WARREN
0 Sewer
0 Metro 0 Standby
Phone:
(206)575 -2000
Street Address P.O. BOX 88050, TUKWILA, WA
98138
City State /Zip:
Fax 575 -1837
Contractor: N/A
Phone:
Street Address:
City State/Zip:
Fax #: RECEIVED
Architect:
N/A
Phone:
SEP 0 9 1996
Street Address:
City State /Zip:
Fax #:
TUKWILA
f UOLIC won :<€
Engineer:
N/A
Phone:
Street Address:
City State /Zip:
Fax #:
MISCELLANEOUSPERMIT REVIEW AND APPROVAL REQUESTED: (TO BE FILLED OUT BY APPLICANT)
Description of work to be done (2) 1}" WATER METER" INSTALLED IN EXISTING METER BOX1i
Will there be storage of flammable /combustible hazardous material in the building? ❑ yes IN no
Attach list of materials and stora • e location on se •arate 8 1/2 X 11 • a • er indicatin • • uantities & Material Safet Data Sheets
■ Above Ground Tanks ■ Antennas /Satellite Dishes ■ Bulkhead/Docks ■ Commercial Reroof
❑ Demolition ❑ Fence ❑ Mechanical ❑ Manufactured Housing - Replacement only
❑ Parking Lots ❑ Retaining Walls ❑ Temporary Pedestrian Protection/Exit Systems
❑ Temporary Facilities ❑ Tree Cutting
MONTHLY SERVICE BILLINGS TO:
Name:
LA PIANTA LIMITED PARTNERSHIP
Phone: (206) 575 -2000
Address:
P.O. BOX 88050
City /State /Zip: TUKWILA, WA
98138
0 Water
0 Sewer
0 Metro 0 Standby
CITY OF "1KWILA
Permit Center
6300 Southcenter Boulevard, Suite 100
Tukwila, WA 98188
(206) 431 -3670
Miscellaneous Permit Application
Application and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or facsimile.
APPLICANT REQUEST .FOR .MISCELLANEOUS PUBLIC WORKS PERMITS`
❑ Curb cut/Access /Sidewalk ❑ Fire Loop /Hydrant (main to vault) #: Size(s):
❑ Land Altering: 0 Cut cubic yards 0 Fill cubic yards 0 sq. ft.grading/clearing
❑ Sanitary Side Sewer #: ❑ Sewer Main Extension 0 Private 0 Public
❑ Street Use ❑ Water Main Extension 0 Private 0 Public
1 "
Size(s): 0 Deduct 0 Water Only
❑ Channelization/Striping
❑ Flood Control Zone
❑ Landscape Irrigation
❑ Storm Drainage
® Water Meter /Exempt #
❑ Water Meter /Permanent # Size(s):
❑ Water Meter Temp # Size(s): Est. quantity: gal Schedule:
❑ Miscellaneous ❑ Moving Oversized Load/Hauling
WATER METER DEPOSIT /REFUND BILLING:
Name: SAME
Address:
Phone:
City /State /Zip:
Value of Construction - In all cases, a value of construction amount should be entered by the applicant. This figure will be
reviewed and is subject to possible revision by the Permit Center to comply with current fee schedules.
Expiration of Plan Review - Applications for which no permit is issued within 180 days following the date of application shall
expire by limitation. The building official may extend the time for action by the applicant for a period not exceeding 180 days
upon written request by the applicant as defined in Section 107.4 of the Uniform Building Code (current edition). No application
shall be extended more than once.
Date application accepted:
Wit' 41
MISCPMT.DOC 7/11/96
Date application expires:
MRic4i �J>>
lApplication taken by: (initials)
, IVV� v
BUILDING OWNER OR AUTH RIZED AGENT:
SUBMIT APPLICATION AND REQUIRED CHECKLISTS FOR
Above Ground Tanks/Water Tanks - Supported directly upon grade
exceeding 5,000 gallons and a ratio of height to diameter or width
which exceeds 2 :1
Signature: pa �J�a�
® i
❑
Date: ,91 .
i w I�(a fe 4
Print name: vAHA ,`y\ '� 't iyi
❑
Phone:5 7 - �ZQ . ,
Fax # : 6 - 75 -, i 37
Address: ac /rc l ..
u-f'k
City / WW'f�c ip: — __
e
❑
SUBMIT APPLICATION AND REQUIRED CHECKLISTS FOR
Above Ground Tanks/Water Tanks - Supported directly upon grade
exceeding 5,000 gallons and a ratio of height to diameter or width
which exceeds 2 :1
PERMIT REVIEW
Submit checklist No: M -9
❑
Antennas /Satellite Dishes
Submit checklist No: M -1
❑
Awnings /Canopies - No signage
Commercial Tenant Improvement
Permit
❑
Bulkhead/Dock
Submit checklist No: M -10
❑
Commercial Reroof
Submit checklist No: M -6
❑
Demolition
Submit checklist No: M -3, M -3a
❑
Fences - Over 6 feet in Height
Submit checklist No: M -9
❑
Land Altering/Grading/Preloads
Submit checklist No: M -2
❑
Loading Docks
Commercial Tenant Improvement
Permit. Submit checklist No: H -17
❑
Mechanical (Residential & Commercial)
Submit checklist No. M -8,
Residential only - H -6, H -16
0
Miscellaneous Public Works Permits
Submit checklist No: H -9
❑
Manufactured Housing (RED INSIGNIA ONLY)
Submit checklist . No: M -5
❑
Moving Oversized Load/Hauling
Submit checklist No: M -5 1
❑
Parking Lots
Submit checklist No: M -4
❑
Residential Reroof - Exempt with following exception: If roof structure
to be repaired or replaced
Residential Building Permit
Submit checklist No: M -6
❑
Retaining Walls - Over 4 feet in height
Submit checklist No: M =1
❑
Temporary Facilities
Submit checklist No: M -7
❑
Temporary Pedestrian Protection/Exit Systems
Submit checklist No: M -4
❑
Tree Cutting
Submit checklist No: M -2
ALL MISCELLANEOUS PE ' APPLICATIONS MUST BE SUBM ED WITH THE FOLLOWING:
➢. * ALL DRAWINGS SHALL BE AT A LEGIBLE SCALE AND NEATLY DRAWN
➢ BUILDING SITE PLANS AND UTILITY PLANS ARE TO BE COMBINED
➢ ARCHITECTURAL DRAWINGS REQUIRE STAMP BY WASHINGTON LICENSED ARCHITECT
➢ STRUCTURAL CALCULATIONS AND DRAWINGS REQUIRE STAMP BY WASHINGTON
LICENSED STRUCTURAL ENGINEER
➢ CIVIVSITE PLAN DRAWINGS REQUIRE STAMP BY WASHINGTON LICENSED CIVIL ENGINEER
(P.E.)
❑ Copy of Washington State Department of Labor and Industries Valid Contractor's License. If
not available at the time of application, a copy of this license will be required before the
permit is issued, unless the homeowner will be the builder OR submit Form H -4, "Affidavit
in Lieu of Contractor Registration ".
Building Owner /Authorized Agent If the applicant is other than the owner, registered architect/engineer, or contractor licensed
by the State of Washington, a notarized letter from the property owner authorizing the agent to submit this permit application and
obtain the permit will be required as part of this submittal.
I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER
PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND 1 AM AUTHORIZED TO APPLY FOR THIS
PERMIT.
MISCPMT.DOC 7/11/96
RECEIVED
CITY OF TUKWILA
SEP 0 9 1996
PERMIT CENTER
RE
SEP « 91996
TUKWILA
PUBLIC WORK -€.
J
Envelope Requirements (enter values as applicable)
Fully heated/cooled.space
Minimum Insulation R- values
Roofs Over Attic
Glazing Area Calculation
Note: Below grade walls may be included in t h e
Gross Exte Wall pa N they are insulated to
the level required for or opaque e walls.
—
Ail Other Roofs
% Glazing
Z'
Opaque Walls
� 7
( l
Below Grade Walls
Applicant Phone:
Floors Over Unconditioned Space
--
Slabs -on -Grade
–"'
Radiant Floors
—
Maximum U- factors
Opaque Doors
d. &c
Vertical Glazing
0.9°
Overhead Glazing
-
f
Maximum SHGC (or SC)
VerticaUOverhead Glazing
1 (.00
Space Heat Type
❑ Electric resistance
Ls, All other (see over for definitions)
Date 4, lZg (a9::.
Glazing Area Calculation
Note: Below grade walls may be included in t h e
Gross Exte Wall pa N they are insulated to
the level required for or opaque e walls.
Total Glazing Area
(rough opening)
(vertical 8 overhd)
Gross Exterior
divided by Wail Area times 100 equals
% Glazing
J � -
j� 0
•
_ 41 1 _ (
.41.2— X X 100 —
� 7
Concrete/Masonry Option
El Check here if using this option and if project meets all requirements for the ConcreteMasonry Option. See
Decision Flowchart (over) for qualifications. Enter requirements for each qualifying assembly in the table below.
Project Info
Project Address Segale Retail Center
Date 4, lZg (a9::.
300 Andover Park West #600
ForBuildin Department Use
Tukwila, WA.
Applicant Name: The Old Navy Store
Applicant Address: 900 Cherry Ave., San Bruno,
CA.
Applicant Phone:
Envelope Summary
Climate Zone 1
ENV -SUM
1994 Washin ' . State Nonresidential Ener
1994 Washington State Nonres denial Energy Code Compliance Forms
Semi- heated space'
Minimum Insulation R- values
Roofs Over Semi - Heated Spaces'
'Refer to Section 1310 for qualifications and requirements
3om a fiance Form
Apnl. 1994
Project Description ❑ New Building ❑ Addition
Alteration ❑ Change of Use
Compliance Option
ti(Prescriptive ❑ Component Performance
(See Decision Flowchart (over) for qualifications)
❑ ENVSTD
❑ Systems
Analysis
Opaque Concrete/Masonry Wall Requirements
Insulation on interior - maximum U- factor is 0.19
Insulation on exterior or integral - maximum U- factor is 0.25
If project qualifies for Concrete/Masonry Option, list walls
with HC 2 9.0 BtuIR°•'F below (other walls must meet
Opaque Wall requirements). Use descriptions and values
from Table 20-5b in the Code.
Wall Description
(including insulation R -value 8 position)
U- factor
RECEIVED
CITY OF TUKWI
Illl fl 1 iqq
PE
)
RMIT CENTER
Notes: vebo.r f fors (A+l 17_, f V(oQ Pf_4e4 T (A) (`.7c,ef.
G (I6 AREA 7- ?i -t D t7,-- 7 0-
f ��- V l
� _ r l
All Insulation installed?
Opaque Walls
Masonry walls (int)
Masonry walls (other)
R -11
U -0.19
U -0.25
Below grade walls (text) R -10
Below grade walls (othr) R -11
Roofs over attics R•30
lAll other roofs
R -21
Floors over uncond.sp.
R -19
Stabs -on -grade
R -10
Radiant floors
R -10
Opaque doors
U -0.60
Glazing Criteria Met!
Glazing Vert OH
SHGC
Area % U U
SHGC
00.15% 0.90 1.45
1.00
15-20% 0.75 1.40
1.00
20-30% 0.60 1.30
0.65
30-40% 0.50 1.25
0.45
All Insulation Installed?
Opaque Walls R -11
Below grade walls (eat) R -10
Below grade walls (othr) R -11
Roofs over attics R -30
All other roofs R -21
Floors over uncond.sp. R -19
Slabs -on -grade • R -10
Radiant floors R•10
Opaque doors 1.1-0.60
Glazing Criteria Met?
Gluing Vert. 011
Area % U U SHGC
00.15% 0.90 1.45 1.00
15-20% 0.75 1.40 1.00
20-30% 0.60 1.30 0.65
30.40% 0.50 1.25 0.45
All Insulation Installed?
Opaque Walls R -19
Masonry walls (int) U -0.19
Masonry walls (other) U -0.25
Below grade walls (ex!) R -10
Below grade walls (othr) R -19
Roofs over attics R -36
All other roofs R -30
Floors aver uncond. R -30
Slabs -on -grade R•10
Radiant floors R -10
Opaque doors U -0.60
Glazing Criteria Met?
Glazing Vert OH
Area % U U • SHGC
00.20% 0.40 0.80 1.00
All Insulation Installed?
Opaque Walla R -19
Below grade *sits (ext) R -10
Below grade walls (otr) R -19
Roofs over attcs
R -38
All other roofs
R -30
Floors over uncond.
R•30
Slabs-on-grade
R -10
Radiant floors
R -10
Opaque doors
U -0.60
Glazing Criteria Mat)
Gluing Vert OH
Area % U U
SHGC
00.20% 0.40 0.80
1.00
Envelope Summary Jack)
Climate Zo
ENV -SUM
1994 Washington State Nonresrdenbal Energy Code Comp fence Forms
Decision Flowchart
for Prescriptive Option
Use this flowchart to determine If project qualifies for the optional Prescriptive Option.
If not, either the Component Performance or Systems Analysis Options must be used.
1302 Space Heat Type: For the purpose of determining building envelope
requtrementa, the following two categories comprise all space heating types:
Other. All other space heating systems Including gas, solid fuel, oil, and propane
space heating systems and those systems listed in the exception to electric
resistance. (continued at right)
\ ,�
/ ..
�' All / Masonry N
<- walls R -11 >- 4 Criteria OK ?
ulab >
Ninson?.' N. no (below) /` yes
\ /
Yes
i'i40%\
'•('\ mg7i
Yes T
no
1994 Washin on State Nonresidential Ener Code Com a liance Form
yes
n o
i
no
L )
r 1
Electric
Resistance
no N. Heat? . .' yes
Prescnptrve
Path Allowed
Component Performance or
Systems Analysis Required
Electric Resistance: Space heating systems which use electric resistance elements
as the pnmary heating system including baseboard. radiant, and forced air um)
when the total electric resistance heat capacity exceeds 1.0 Wfle 01 the gross
conditioned floor ens. Exception: Heat pumps and terminal electric resistance
heating in vanable au volume distribution systems.
e - <20%
Yes Gazing?/ o
T
no
Ns
M asonry \
(Nall Criteria OK
Yes \ (below)
Ap
7 }4 walls R-19 )
no ‘insulator ? /
yes
no lazing?/
Concrete/Masonry Option*
Assembly Description
Wall Heat Capacity (HC)
Assy.Tag
NC**
Area (sf)
Totals
Area weighted HC: divide total of (HC x area) by Total Area
HC x Area
no
Apnl. 1994
*If the area
weighted heat
capacity (HC) of
the total above
grade wall is a
minimum of 9.0,
the Concrete
Masonry Option
may be used.
For framed
walls, assume
HC =1.0 unless
calculations are
provided; for all
other walls, use
Section 2009.
Stiv lst'&16��tzv:!H'awa'a.:a? „F tks x<aa�+ r�gy ' * J
�itkS :d 'S•T: h
MONTGOMERY & ERTS
Consulting Engin s
11090 San Pablo Avenue
EL CERRITO, CALIFORNIA 94530
(510) 232.1541 fax (510) 232 -0865
PRODUCT 2O41($m Is Shots) 2D5.1 (Pandadi /Rend /. Ina, crown, wa 0I4/l. to No PHONE TOLL FREE I.OW 225.6980
°O. it. `' v"o'sramSki.°mn.fi':nt,. [fc'Im::°i tueg iolteF. DIES /I:hmstf! L' tVT9p 'Y,.. �.RC�.�.,� tlw!;.
JOB 0 7 .4 5 19
SHEET NO .441
OF
CALCULATED BY Ce's.,Vr DATE
CHECKED BY G.W DATE
SCALE
��s r�Flw Rte -:
A-r
FF-tistr TrK
E.Pta(44 Prg P t
c6x(5 4- zc6,x 4-e-f-czh 3 frtgl
* 74, tA 6 14 1,
(•t ((r2.1x,
76L4NC1 = f q�
Building Permit Plans Checklist ENV -CHK
1994 Washington Slate Energy Code Compliance Forms Apnl. 1994
Project Address 300 Andover Park West, 11600
Date
The following information is necessary to check a building permit application for compliance with the building envelope requirements in the
Washington State Nonresidential Energy Code.
Applicability
(circle one)
Code
Section
Component
Information Required
Location
on Plans)
I Building Department
• Notes
GENERAL REQUIREMENTSjSections 1301 -1314)
1301 Scope
Unconditioned spaces identified on plans if allowed
1302 Space heat type
yes no n.a.
Electric resistance
.
es no n.a.
Other
Indicate on •tans that electric resistance heat is not allowed
yes no n.a.
1310.2 Semi- heated spaces
Semi- heated spaces identified on plans if allowed
1311 Insulation
yes no n.a.
1311.1 Insul. installation
Indicate densities and clearances
yes no n.a.
1311.2 Roof /ceiling insul.
Indicate R -value on roof sections for attics and other roofs;
Indicate clearances for attic insulation;
Indicate baffles if eave vents installed;
Indicate face stapling of faced batts
•
yes no n.a.
1311.3 Wall insulation
Indicate R -value on wall sections;
Indicate face stapling of faced batts;
Indicate above grade exterior insulation is protected;
Indicate loose -fill core insulation for masonry walls as necess;
Indicate heat capacity of masonry walls
if masonry option is used or if credit taken in ENVSTD;
yes no n.a.
1311.4 Floor insulation
Indicate R -value on floor sections;
Indicate substantial contact with surface;
Indicate supports not more than 24" o.c.;
Indicate that insulation does not block
airflow through foundation vents
yes no n.a.
1311.5 Slab -on -grade floor
Indicate R -value on wall section or foundation detail;
Indicate slab insulation extends down vertically 24" from top;
Indicate above grade exterior insulation is protected
yes no n.a.
1311.6 Radiant floor
Indicate R -value on wall section or foundation detail;
Indicate slab insulation extends down vertically 36" from the top;
Indicate above grade exterior insulation is protected;
Indicate insulation also under entire slab where req'd. by Official
yes no n.a.
1312 Glazing and doors
Provide calculation of glazing area (including both vertical
vertical and overhead) as percent of gross wall area
yes no n.a.
1312.1 U- factors
Indicate glazing and door U- factors on glazing and door
schedule (provide area - weighted calculations as necessary);
Indicate If values are NFRC or default, if values are default
then specify frame type, glazing layers, gapwidth, low-e •
coatings, gas fillings
yes no n.a.
1312.2 SHGC 8 SC
Indicate glazing solar heat gain coefficient or shading
coefficient on glazing schedule (provide area - weighted
calculations as necessary)
1313 Moisture control
yes no n.a.
1313.1 Vapor retarders
Indicate vapor retarders on warm side
yes no n.a.
1313.2 Roof /ceiling vap.ret.
Indicate vapor retarder on roof section;
Indicate vap. retard. with sealed seams for non -wood struc.
yes no n.a.
1313.3 Wall vapor retarder
Indicate vapor retarder on wall section
yes no n.a.
1313.4 Floor vapor retarder
Indicate vapor retarder on floor section
es no n.a.
1313.5 Crawl s •ace va•. ref.
Indicate six mil black • •l eth ene overla• • - • 12" on •round
1314 Air leakage
yes no n.a.
es no n.a.
1314.1 Bldg. envel. sealing
1314.2 Glazin• /door sealin•
Indicate sealing, caulking, gasketing, and weatherstripping
Indicate weatherstji. .j,.
_
es no n.a.
1314.3 Assemb. as ducts
Indicate sealin•, caulkin• and •asketin•
PRESCRIPTIVE/COMPONENT PERFORMANCE (Sections 1320 -23 or 1330 -34)
yes no
Envelope Sum. Form
Completed and attached.
Provide component performance worksheet if necessary
Provide ENVSTD screen 1 out•ut if necessa
1994 Washing State Nonresidential Energy Cod . 'ompliance Form
no is circled for any question, provide explanation:
1994 Washing± ^n State Nonresidential Energy CodP Compliance Form
Building Permit Plat s Checklist
1994 Washington State Energy Coda Compliance Forms
ENV -CHK
Apnl, 1994
Envelope - General Requirements
1311 Insulation
1311.1 installation Requirements: Ail insulation materials shall be
installed according to the manufacturer's instructions to achieve proper
densities, maintain clearances, and maintain uniform R- values. To the
maximum extent possible, insulation shall extend over the full component
area to the intended R- value.
1311.2 Roof /Ceiling Insulation: Open -blown or poured loose -fill
insulation may be used in attic spaces where the slope of the ceiling is
not more than 3/12 and there is at least thirty Inches of clear distance
from the top of the bottom chord of the truss or ceiling joist to the
underside of the sheathing at the roof ridge. When eave vents are
installed, baffling of the vent openings shall be provided so as to deflect
the incoming air above the surface of the insulation.
Where lighting fixtures are recessed into a suspended or exposed grid
.ceding, the roof /ceiling assembly shall be insulated in a location other than
directly on the suspended ceiling.
Exception: Type IC rated recessed lighting fixtures.
Where installed in wood framing, faced bait insulation shall be face
stapled.
1311.3 Wall Insulation: Exterior wall cavities isolated during framing
shall be fully insulated to the levels of the surrounding walls. When
installed in wood framing, faced batt insulation shall be face stapled.
Above grade exterior insulation shall be protected.
1311.4 Floor Insulation: Floor insulation shall be installed in a
permanent manner in substantial contact with the surface being insulated.
Insulation supports shall be installed so spacing is not more than twenty-
four inches on center. Installed insulation shall not block the airflow
through foundation vents.
1311.6 Slab -On -Grade Floor: Slab -on -grade insulation installed inside
the foundation wat shall extend downward from the top of the slab a
minimum distance of twenty-four inches or to the top of the footing,
whichever is Tess. Insulation installed outside the foundation shall extend
downward a minimum of twenty-four inches or to the frostline, whichever
is greater. Above grade insulation shall be protected.
Exception: For monolithic slabs, the insulation shall extend
downward from the top of the slab to the bottom of the footing.
1311.6 Radiant Floors (on or below grade): Slab -on -grade insulation
shall extend downward from the top of the slab a minimum distance of
thirty -six inches or downward to the top of the footing and hor for an
aggregate of not less than thirty -six inches.
If required by the building official where soil conditions warrant such
insulation, the entire area of a radiant floor shall be thermally isolated from
the soil. Where a soil gas control system is provided below the radiant
floor, which results in increased convective flow below the radiant floor,
the radiant floor shall be thermally isolated from the sub -floor gravel layer.
1312 Glazing and Doors
1312.1 Standard Procedure for Determination of Glazing and Door
U- Factors: U- factors for glazing and doors shall be determined. certified
and labeled in accordance with Standard RS -31 by a certified
independent agency licensed by the National Fenestration Rating Council
(NFRC). Compliance shall be based on Model Size AA or BB. Product
samples used for U- factor determinations shall be production line units or
representative of units as purchased by the consumer or contractor.
Unlabeled glazing and doors shall be assigned the default U- ?actor in
Section 2006.
1312.2 Solar Heat Gain Coefficient and Shading Coefficient: Solar
Heat Gain Coefficient (SHGC), shall be determined, certified and labeled
in accordance with the National Fenestration Rating Council (NFRC)
Standard by a certified; independent agency, licensed by the NFRC.
Exception: Shading coefficients (SC) shall be an acceptable
alternate for compliance with solar heat gain coefficient
requirements. Shading coefficients for glazing shall be taken from
Chapter 27 of Standard RS -27 or from the manufacturer's test
data.
1313 Moisture Control
1313.1 Vapor Retarders: Vapor retarders shall be installed on the warm
side (in winter) of insulation as required by this section.
Exception: Vapor retarder installed with not more than 1/3 of the
nominal R -value between it and the conditioned space.
1313.2 Root /Ceiling Assemblies: Roof /ceiling assembles where the
ventilation space above the insulation is less than an average of twelve
inches shall be provided with a vapor retarder. Roof/ceiling assemblies
without a vented airspace, where neither the roof deck nor the roof
structure are made of wood, shall provide a continuous vapor retarder
with taped seams.
Exception: Vapor retarders need not be provided where all of
the Insulation is installed between the roof membrane and the
structural roof deck.
1313.3 Walls: Walls separating conditioned space from unconditioned
space shall be provided with a vapor retarder.
1313.4 Floors: Floors separating conditioned space from unconditioned
space shall be provided with a vapor retarder.
1313.6 Crawl Spaces: A ground cover of slot mil (0.006 inch thick) black
polyethylene or approved equal shall be laid over the ground within crawl
spaces. The ground cover shall be overlapped twelve inches minimum at
the joints and shall extend to the foundation wall.
Exception: The ground cover may be omitted in crawl spaces
if the crawl space has a concrete slab floor with a minimum
thickness of three and one -half inches.
1314 Air Leakage
1314.1 Building Envelope: The requirements of this section shall apply
to building elements separating conditioned from unconditioned spaces.
Exterior joints around windows and door frames, openings between walls
and foundation, between wails and roof and wall panels: openings at
penetrations of utility services through walls, floors, and roofs; and ail
other openings in the building envelope shall be sealed, caulked,
gasketed, or weatherstripped to limit air leakage.
1314.2 Glazing and Doors: Doors and operable glazing separating
conditioned from unconditioned space shall be weatherstripped. Fixed
windows shall be tight fitting with glass retained by stops with sealant or
caulking all around.
Exception: Openings that are required to be fire resistant.
1314.3 Building Assemblies Used as Ducts or Plenums: Budding
assemblies used as ducts or plenums shall be sealed. caulked, and
gasketed to limit as leakage.
Project Address 300 Andover Park West #600
Date
Space Heat Type
❑ Electric resistance ❑ All other
For Building Department Use
Glazing Area as % gross exterior wall area
%
Concrete/Masonry Option
❑ Yes ❑ No
Notes: If glazing area exceeds maximum allowed in Table, then calculate adjusted areas on back (over). If Concrete/Masonry Option is used,
Target U- factors, SHGC and Glazing % will be different than shown below. Refer to Table 13 -1 for correct values.
Building Component
List components by assembly ID & page #
Proposed UA
U- factor x Area (A) = UA (U x A)
Target UA
U- factor x Area (A) = UA (U x A)
6ulzeID
to 14aA
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
Glazing % Electric Resist.. Other Heating
. 0.15% 0.40. 0.90'.
>15 -20% 0.40:. :. : 0.75
t allowed : : ` ' . 0.60:
2030% ' rid
>2t1-3
>30 -40% not. allowed •• .:. .• 0.50
(see Table 13-1 for ConclMasonry values)
6ulzelo
peaymn0
U= Plan ID:
U= Plan ID:
U= Plan ID: -
U= Plan ID:
U= Plan ID:
U= Plan ID:
U= Plan ID:
Glazing.% Electric Resist. . Other Heating
' 0.15% . 0.80 - . :1.45 '. •
>15 -20% 0.80. ' .1.40
>20.30% not allowed 1.30
>30 -40% . not allowed • 1.25.;
.
(see Table 13-1 for Conc/Masonry values)
Opaque
Doors
U= Plan ID:
U= Plan ID:
U= Plan ID:
:Electric Resist . . Other Heating
• 0.60 0.60
JaA0
s)ooa
_
R= Plan ID:
R= Plan ID:
R= ' Plan ID:
Electric Resist. Other Healing
0.031 0.036
SJOOd
JaWlo
R= Plan ID:
R= Plan ID:
R= Plan ID:
Electric Resist. Otter Heating
0.034 0.050 •
Opaque Walls'
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
Electric Resist. .Other Heating
Ordnary • 0.062 0.14
Metal stud 0.11 • 0.14
Conc(int) ' 0.19 • '.'0.19'
Conc(oth). • '0.25 • .0.25
Below
(Grade Walls
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
'Electric Resist. . Other Heating
'Ordinary 0.062 0.14
Metal stud '0.11 ' • 0.14
I Floors Over I
Uncond. Sp.
-
R = Plan ID:
R= Plan ID: •
R= Plan ID:
R= Plan ID: -
•
Electric Resist.. Other Heating
0.029 0.056
I apei6 1
R= Plan ID:
R= Plan ID:
R= Plan ID:
R= Plan ID:
Electric Resist. Other Heating
' F =0.54 F =0.54
(see Table 13.1 for radiant floor.velues)
For CMU walls, indicate core insulation material.
Totals!
For compliance:
Totals!
•
Envelope UA Calculations Climate Zone 1
ENV -UA
1994 Washi :n State Nonresidential Ener C e? ' , Com a liance Form
1994 Washington State Nonresidential Energy Code Compliance Forms
April, 1994
1) Proposed Total Area shall equal Target Total Area, and 2) Proposed Total UA shall not exceed Target Total UA.
1: OG=
2: OG=
3: VG=
4:
5:
6:
Vertical Glazing
List components by assembly ID & page #
Proposed SHGC
SHGC' x Area (A) = SHGC x A
Target SHGC
SHGC x Area (A) = SHGC x A
6uRe10
leollnA
Plan ID:
Plan ID:
Plan ID:
Plan ID:
Plan ID:
Plan ID:
Glazing % Electric Resist. Other Heating
0-20% 1.00. 1.00'
>20-30% not allowed • 0.65
>30-40% not arrived 0.45
(see Table 13.1 for Cone/Masonry values)
'Note: Manufacturer's SC may be used In lieu of SHGC.
For compliance:
Totals
Totals'
Overhead Glazing
List components by assembly ID & page #
Proposed SHGC
SHGC' x Area (A) = SHGC x A
Target SHGC
SHGC x Area (A) = SHGC x A
Overhead Glazing
Plan ID:
Plan ID:
Plan ID:
Plan ID:
Plan ID:
Plan ID:
Glazing % Electric Resist. Other Heating
0.20% 1.00 1.00
>20 -30% not allowed 0.65
>30 -40% not allowed 0.45
(see Table 13-1 for Conc/Masonry values)
'Note: Manufacturer's SC may be used in lieu of SHGC.
Totals
For compliance:
Totals
Envelope SHGC C. lations Climate Zone
ENV -SHGC
1994 Washington State Nonresidential Energy Code Compliance Forms
Target Area Adjustment Calculations
If the total amount of glazing area as a % of gross exterior wall area (calculated on ENV -SUM) exceeds the maximum allowed in Table 13-1,
then this calculation must be done. Use the resulting areas in the Target UA and SHGC calculations above.
Glazing Area
Opaque Area
Gross Exterior Wall
Area
1x1 opal = 100 =17:
17:
Roofs over Attics
Other Roofs
Walls'
1994 Washin ton State Nonresidential Ener Code Com • 'lance Form
1) Proposed total area shall equal Target Total Area, and 2) Proposed Total SHGC shall not exceed Target Total SHGC.
1) Proposed total area shall equal Target Total Area, and 2) Proposed Total SHGC shall not exceed Target Total SHGC.
Proposed Areas: Numbered values are used in calculations below.
Roofs over Attics Other Roofs Walls
Target OG Area In Roofs over Attics
Max OG Remaining
Max Glazing Area
(Table 13 -1)
1:
II lesser (circle)
7:
•
4:
5:
Proposed Opaque Area
1 6:
18: 1
Proposed Opaque Area Proposed OG Area
+
1:
2:
Proposed VG Area
1 3:
Target OG Area in Other Roofs
Total Ta get OG Area (sum #10 + 1111)
Maximum Target
Glazing Area
2:
II lesser (circle)
8:
Target OG Area W
10:
11:
12:
Target VG Area
Target VG Area
1 9:
Target Opaque Area
13:
14:
Target Opaque Area
115 :
+ — 1 9 : =
Note: If there is more than one type of wall, the Target VG Area may be distributed among them, and separate Target Opaque Areas found.
Target values 9, 12,13,14 & 15 (shaded boxes) are used in the applicable Target UA calculations on the front.
Target values 9 & 12 are also used in the applicable Target SHGC calculations above.
April, 1994
Note:
OG = overhead glazing
VG = vertical glazing
For Target OG's, circle
and use the lesser
values both here and
below.
Fan Equipment Schedule -
Equip.
ID
,
Brand Name'
Model No.'
CFM
SP'
HP /BHP
Flow Control
Location of Service
CE
bt-cK
.----(7"
VF
a 75
(W
. , . ,
- 7121 PS-
col,
6i(`z f-{ 44k
r?
(ZS
0.575"
7C liJ
Yiig- ST-64>
'jar t4 g f1 i•
I $o,00O
ferifrod
t aZ- 9 0
e '� '
f e t&
Ec-r(c
r. r' Me- _,rla
•■
r . _ri
414(O -f
imcAtle,
tiff -F-P 19-- •
Zo1.c.W
1 o
— •
—
—
--
Cooling Equipment Schedule
Equip.
ID
Brand Name'
Model No.'
Capacity
Total CFM
OSA CFM
Econo
SEER
ott
IPLV
Location
,rk,4"
CfrFF I
4 'f•LP01
2.s r-i y
eio Di?
6.0/7
J (. b
97
437-x,
.RA65
' "(ft
4%ri
(41,6t400
4-000
(, 00
I $o,00O
ferifrod
t aZ- 9 0
e '� '
f e t&
Ec-r(c
r. r' Me- _,rla
•■
r . _ri
414(O -f
imcAtle,
tiff -F-P 19-- •
Zo1.c.W
1 o
— •
—
—
--
_
Heatin; E. ui I ment Schedule
Equip.
ID
Brand Name'
Model No.'
Capacity
Total CFM
OSA cfm
Econo
Input Btuh
Output Btuh
Efficiency`
, ,.
41/41M111
, ; ND a12—
, :
4 bob
(orbt)
; o-0
'' 600
437-x,
.RA65
' "(ft
4%ri
(41,6t400
4-000
(, 00
I $o,00O
ferifrod
t aZ- 9 0
e '� '
f e t&
Ec-r(c
r. r' Me- _,rla
•■
r . _ri
414(O -f
imcAtle,
tiff -F-P 19-- •
Zo1.c.W
1 o
— •
—
—
--
_
Project Info
Project Address 300 Andover Park West #600
Date
2_0 c3
- tvKW ILA
For Building
epart ent Use
f
Applicant Name: o� t l C- , crrp r/Y��
Applicant Address:
g i+ 1J,; ,r� p e / ��� ��/�" '' ow) e
..JJ C/risi1�1�7 rJ r{/
Applicant Phone:
1994 Washin/" -t State Nonresidential Ener Co. Com•liance Form
Mechanical Summary
•
MECH -SUM
1994 Washington State Nonresidential Energy Code Compliance Forms
Apnl. 1994
Project Description
Briefly describe mechanical system
type and features.
trJSTALL- (-- { Tf7* PovF'•i 64ste. tc-rgfe
v�r�
over_ r (44 "4r- q4GP--
Compliance Option
Simple System ❑ Complex System ❑ Systems Analysis
(See Decision Flowchart (over) for qualifications)
Equipment Schedules
The following information is required to be incorporated with the mechanical equipment schedules on the
plans. For projects without plans, fill in the required information below.
'If available. 2 As tested according to Table 14-1, 14-2 or 14-3. 3 If required. ` COP, HSPF, Combustion Efficiency, or AFUE, as applicable.
s Flow control types: VAV, constant volume, or variable speed.
C\
System Description
See Section 1421 for full description of
Simple System qualifications.
If Heating/Cooling
or Cooing Only:
la vol?
❑ Split system?
ZrAlr cooled? Packaged sys? ❑ <54,000 Btuh?
Economizer included?
If Heating Ony
❑ <5000 cfm?
❑ <70%
<70,5 outside air?
Mechanical Summary (back)
MECH -SUM
1994 Weshinpton Sr. et Nonressdonlal Energy Code Compliance Forms
Decision Flowchart
Use this flowchart to determine if project qualifies for Simple System Option. If not, either the
Complex System or Systems Anaysis Options must be used.
System Type
<5000 cfm
<70% OA
eating /Cooling
or Cooling Only
ackage
stem?
Split
stem?
54,000 Btu
r 1900 cfm
54,000 Btu
r 1900 cfm
onstan
olume
Ir Cooled .
Reference
Sec. 1430
Heating On
no
no
Complex Systems
L V
1994 Washington State Nonresidential Energy Code Compliance Form
yes
yes
Reference
■ Sec. 1423
4 Simple System l
Allowed
Reference
Sec. 1420
yes
yes
no
Use Complex
- System
Apnl. 1994
Refer to MECH -COMP Mechanical Complex Systems for assistance In determining which Complex
Systems requirements are applicable to this project.
Mechanical Permit Plans Checklist MECH -CHK
1994 Washington Stale Energy Code Compliance Forms Apnt, 1994
Project Address 300 Andover Park West #600
(Date 6,42
The following Information is necessary to check a mechanical permit application for compliance with the mechanical requirements in the
Washington State Nonresidential Energy Code.
Applicability Code
(circle one) Section Component Information Required
Location
on Plans
Building Department
Notes
HVAC RE UIREM S JSections 1101-1424)
1411
Eqpmt performance
s no . 1411.4
Pkg. elec. htg.d cig.
Minimum efficiency
_
List heat pumps on schedule
Equipment schedule with type. capacity, efficiency
Pt (,}
no n.a.
1411.1
1412
HVAC controls
no n.e.
1412.1
Temperature zones
Indicate locations on plans
M2,1
no rl,a.
1412.2
Deadband control
Indicate 5 degree deadband minimum
MP1,Q
no .a 1412.3
Humidity control
Indicate humidistat
--
no n.e. 1412.4
g3
Automatic setback
Indicate thermostat with night setback and 7 different day types
Meta
no n.e. 1412.4.1
Dampers
Indicate damper location and automatic controls
My, t
yes no 1412.5
Heat pump control
Indicate microprocessor on thermostat schedule
—
,
no n. 1412.6
Combustion htg.
Indicate modulating or staged control
—
117 no n,a. 1412.7
Balancing
Indicate balancing features on plans
(12-,}
' s no n.a. 1422
Thermostat interlock
Indicate thermostat interlock on plans
r t-O
('ice no n.a. 1423
Economizers
Equipment schedule
M I. I
1413
Air economizers
i - no n.a. 1413.1
Operation
Indicate 100% capability on schedule
('If..!
6'a, no n.a. 1413.2
Control
Indicate controls able to evaluate outside air
MP!. b
no n.a. 1413.3
Integrated operation
Indicate capability for partial cooling
MJ_ f
1414
Ducting systems
no n.a. 1414.1
Duct sealing
Indicate sealing necessary
MPtr•0
no n.a. 1414.2
Duct insulation
Indicate R -value of insulation on duct
-4
es no 1415.1
Piping insulation
Indicate R -value of Insulation on piping
-MPI
—�
no n.a. 1424
Separate air sys.
Indicate separate systems otulans
141,024
no
Mech. Sum. Form
Completed and attached. Equipment schedule with types,
input/output, efficiency, cfm, hp, economizer
A
�t
SERVICE NATER
REAM AND HEATED POOLS (Sections 1440 -1454)
1440
Service water htg.
yes no .a
1441
Elec. water heater
Indicate R -10 insulation under tank
i
yes no
1442
Shut -off controls
Indicate automatic shut -off
—
1450
Heated pools
—.
yes no .a
1452
Pool water heaters
Indicate not electric resistance
--
yes no .a
1453
Pool heater controls
Indicate switch and 65 degree control
yes no
1454
Pool covers
Indicate vapor retardant cover
—
,
Yes no ,a
1454 Pools 90+ degrees
Indicate R -12 pool cover
—'
i: :: S. iiEY;;!j'$iC'�`.kT.�.`,r:s'.':a
1994 Washing State Nonresidential Energy Codf ompliance Form
no circled f any question, provide explanation:
.C:�i�lr�goa'.::.r. F.;: s�^ , ^.rmsz'�• >, rorm
�.1
1994 Washinconn State Nonresidential Energy Cod^ Compliance, Form
Mechanical Permit ans Checklist
1994 Washington State Energy Code Compliance Forms
MECH -CHK
April, 1994
Mechanical - General Requirements
1412 Controls
1412.1 Temperature Controls: Each system shall be provided with at
least one temperature control device. Each zone shall be controlled by
individual thermostatic controls responding to temperature within the zone.
At a minimum, each floor of a building shall be considered as a separate
.. zone.
1412.2 Deadband Controls: When used to control both comfort heating
and cooling, zone thermostatic controls shall be capable of a deadband of at
least 5 degrees F within which the supply of heating and cooling energy to
the zone is shut off or reduced to a minimum.
Exceptions:
1. Special occupancy, special usage, or code requirements where
deadband controls are not appropriate.
2. Buildings complying with Section 1141.4, if in the proposed
building energy analysis, heating and cooling
thermostat setpoints are set to the same temperature
between 70 degrees F and 75 degrees F inclusive,
and assumed to be constant throughout the year.
3. Thermostats that require manual changeover between heating
and cooling modes.
1412.3 Humidity Controls: If a system is equipped with a means for
adding moisture, a humidistat shall be provided.
1412.4 Setback and Shut-Off: HVAC systems shall be equipped with
automatic controls capable of accomplishing a reduction of energy use
through control setback or equipment shutdown during periods of non -use
or alternate use of the spaces served by the system. The automatic controls
shall have a minimum seven -day clock and be capable of being set for
seven different day types per week.
Exceptions:
1. Systems serving areas which require continuous operation at the
same temperature setpoint.
2. Equipment with full load demands of 2 kW (6,826 Btu/h) or less
may be controlled by readily accessible manual off-
hour controls.
1412.4.1 Dampers: Outside air intakes, exhaust outlets and relief outlets
serving conditioned spaces shall be equipped with dampers which close
automatically when the system is off or upon power failure. Stair shaft and
elevator shaft smoke relief openings shall be equipped with normally open
dampers. These dampers shall remain closed in normal operation until
activated by the fire alarm system or other approved smoke detection
system.
Exceptions:
1. Systems serving areas which require continuous operation.
2. Combustion air intakes.
1412.5 Heat Pump Controls: Unitary air cooled heat pumps shall include
microprocessor controls that minimize supplemental heat usage during
start-up, set -up, and defrost conditions. These controls shall anticipate
need for heat and use compression heating as the first stage of heat.
Controls shall indicate when supplemental heating is being used through
visual means (e.g., LED indicators).
1412.6 Combustion Heating Equipment Controls: Combustion heating
equipment with a capacity over 225,000 Btu /h shall have modulating or
staged combustion control.
Exceptions:
1. Boilers.
2. Radiant Heaters.
1412.7 Balancing: Each air supply outlet or air or water terminal device
shall have a means for balancing, including but not limited to, dampers,
temperature and pressure test connections and balancing valves.
1413 Air Economizers
1413.1 Operation: Air economizers shall be of automatically modulating
outside and return air dampers to provide 100 percent of the design supply
air as outside air to reduce or eliminate the need for mechanical cooling.
1413.2 Control: Air economizers shall be controlled by a control system
capable of determining if outside air can meet part or all of the building's
cooling loads.
1413.3 Integrated Operation: Building Heating Energy: Air
economizers shall be capable of providing partial cooling even when
additional mechanical cooling is required to meet the remainder of the
cooling load. Controls shall not preclude the economizer operation when
mechanical cooling is required simultaneously.
Exception: Economizers on individual, direct expansion, cooling
systems with capacities not greater than 75,000 Btu/h may
include controls that limit simultaneous operation of the
economizer and mechanical cooling for the,purpose of preventing
ice formation on cooling coils.
1414 Ducting Systems
1414.1 Sealing: Duct work which is designed to operate at pressures
above 1/2 inch water column static pressure shall be sealed in accordance
with Standard RS -18. Extent of sealing required is as follows:
1. Static pressure: 1/2 inch to 2 inches; seal transverse joints.
2. Static pressure: 2 inches to 3 inches; seal all transverse joints
and longitudinal seams.
3. Static pressure: above 3 inches; seal all transverse joints,
longitudinal seams and duct wall penetrations.
1414.2 Insulation: Ducts and plenums that are constructed as part of the
building envelope shall meet the requirements of Chapter 13. Other ducts
and plenums shall be thermally insulated per Table 14 -5.
Exceptions:
1. Within the HVAC equipment.
2. Exhaust air ducts not subject to condensation.
3. Exposed ductwork within a space that serves that space only.
1415 Piping Systems
1415.1 Insulation: Piping shall be thermally Insulated in accordance with
Table 14-6.
Exception: Piping installed within unitary HVAC equipment.
Water pipes outside the conditioned space shah be insulated in
accordance with Washington State Plumbing Code (WAC 51 -26)
1420 SIMPLE SYSTEMS (PACKAGED UNITARY EQUIPMENT)
1421 System Type: To qualify as a simple system, systems shall be one of
the following:
a. Air cooled, constant volume packaged equipment, which provide
heating, cooling or both, and require only external
connection to duct work and energy services.
b. Air cooled, constant volume split systems, which provide heating,
cooling or both, with cooling capacity of 54,000 Btu/h
...or less.
c. Heating only systems which have a capacity of less than 5,000
cfm or which have a minimum outside air supply of
less than 70 percent of the total air circulation.
All other systems shall comply-with Sections 1430 through 1438.
1422 Controls: In addition to the control requirements in Section 1412,
whore separate heating and cooling equipment serve the same temperature
zone, thermostats shall be interlocked to prevent simultaneous heating and
cooling.
1423 Economizers: Economizers meeting the requirements of Section
1413 shall be installed on packaged roof top tan - cooling units having a
supply capacity of greater than 1,900 cfm or a total cooling capacity greater
than 54,000 BtUTh.
The total capacity of all units without economizers shall not exceed
240,000 Btu/h per building.
1424 Separate Air Distribution Systems: Zones with special process
temperature requirements and/or humidity requirements shall be served by
separate air distribution systems from those serving zones requiring only
comfort conditions.
Mechanical - Complex Systems Checklist MECH -COMP
1994 Washington State Energy Code Compliance Forms Apnl, 1994
Project Address
300 Andover Park Wggt #600
Date
The following additional information is necessary to check a mechanical permit application for a complex mechanical
system for compliance with the mechanical requirements in the Washington State Nonresidential Energy Code. Use
the checklist as a reference for notes added to the mechanical drawings (see the MECH -CHK checklist for additional
system requirements). This information must be on the plans since this Is the official record of the permit. Having
this information In separate specifications alone is NOT an acceptable alternative.
For Building Department Use
Applicability I
(circle one)
Code
Section (Component
Information Required
Location
on Plans
Building. Department
Notes
ADDITIONAL CHECKLIST ITEMS FOR COMPLEX SYSTEMS ONLY
yes no n.e.
1431.1
Field assem. sys.
Provide calculations
1432
Controls
yes no n.a.
1432.1
Setback 8 shut -off
Indicate seprate systems or show isolation devices on plans
1432.2
Temp. reset control
yes no n.a.
1432.2.1
Ak systems
Indicate automatic reset
no n.a.
1432.2.2
H . tunic s terns
Indicate automatic reset
yes no n,a.
1433
Economizers
Indicate economizer on equipment schedule or provide
calculations to justify exemption
yes no n.a.
1434
Separate air sys.
Indicate separate systems on plans
yes no n.a.
1435
'Simul. htg. 8 clg.
.
Indicate that simultaneous heating and cooling is prohibited,
unless use of exception is justified
yes no n.a.
1436
Heat recovery
Indicate heat recovery on plans;
complete and attach heat recovery calculations
1
yes no n.a.
1437
motor effic.
MECH -MOT or Equip. Schedule with hp, rpm, efficiency
Yes no n.a.
1438
4 Elec.
Variable flow sys. Indicate variable flow on fan and pump schedules
• •
'� itkdx�
Seale" 14324
Hot Water Supply
Tempeature Rent
Controls Requited
No
1994 Washin State Nonresidential Energy Cot Form
no is circled for any question, provide explanation:
Decision Flowchart
Use this flowchart to determine how the requirements of the Complex Systems Option apply to the
project. Refer to the indicated Code sections for more complete information on the requirements.
Capacity of HW
Heating System
Otesta Thus
000.000 Btuh"
Start
Here
Settee 1411.1
Equipment Pert.
Shan Meet Tables
14-1 through 14.3
Field.
s. Mumbled
• ••,Eqr , , •
No�
•
No • System
Multiple
Zona
U
Yes
Seeds* 1431.1
Cakuiauau or
Total On •site Energy
input & Output
Required
Stales 1432.2.1
Supply Air Reset
Controls
Requited
t
(continued on
back)
n5'efibec.]+::rt az» c. �r. r. rc• ar , e•xt�..�c:t!��•�R:.ai��;..�.a� .�.�- �ne�ex<.
62)
echanical - Comr.x Systems (back)
S
MECH-COMP
1991 Washington State Nonresidents( Energy Code Compliance Forms
Seetlee1411.4
Must be
Heat Pump
1411.5
Provide
Microprocessor
Heat Pump
Controls
1994 Washin•ton State Nonresidential Ener• Code Corn liance Form
0
0
No
(continued
from front)
/N
Yes ce°1 s Yes ,/ Heat ing & \ pectic Heatin.'•
CaPacilY C°4". N
• 20,000 ,
N Packae? •
Btri / \Ny./ Fuel
\
••
riupply Air >•'.. Yes
5000 CFM \
Outside Air >
7014?
V
Done l
I • ..
/ •
Seetfic ....
<.........., Efficiency '`..... No . ,. speed ' N
included in Equipmer >-0.•< Motor in a %
Performance . ' / \ Multi-speed /
Retinal . System? i '
•7 \ ., .../.
Yes
Non-Electric
Yes
..,,Capacity?
No
Stollen 1433
Air-Side
Economizer
Required
ao•
\ % • •
Yes
Yes
Settles 1411.4
Modulating
or Staged
Combustion
Controb
Required
Sedate 1434
50% Effective
Heat Recovery
System Required
App lication Yes Yes
pans or Pump'
„V.ariainblevolvXows; 10 HP7
• •
•`■
N
No No
7 N
Studio 1435
Fen Powered Y " vAv
Terminal Unita System? ,• ■
Required N ,/
...".....
.,. ...., • .„. \ i
..• Cooling .. Yea / Packaged N. No „ • Cooling • -.., No ,.., Total 1:114 -.. No
Capacity> :-10.4, Rooftop "— Capacity > :,--4.: e > • ;.—..—
'.,54,000 Otuh?./ - .• ' • , 84,000 Otuh?,.. • •' N. , 240 , 000 8tuh? ../•
...•
'N. ./
N.. "
Yea
NOT
Settles 1435
Simultsneoue
Heating k
Cooling Prohibited
Section 1437
Moton Must Meet
Ef5ciencies
Table 14-4
Apnl, 19134
Li •
Jos No
.... s9+' tatimuctraiu`vti 1
ENGIIERS- NORTHWESTNC. P.S.
6869 WOODLAWN AVE. N.E. - SUITE 205 - SEATTLE, WA 98115 (206)525 -7560 - FAX # (206) 522 -6698
{ • 1„ L ' � DATE 6 - IS "9.6
SUBJECT SHEETCLO OF
BY ft • Rs1110 t2..
JOB NAME
■?_0(1‘02At... citLcutAioNs
ro -
61 I? 2 N 0 0YL_ ' LE'R I L I ,-�-
1\h(W I Lit K3 A514 ttJ rD fJ
6Q(k) If 530k(-`01
EXPIRES 11/12/ 4 14 I
RECEIVED
CITY OF TUKWILA
JUL 011996
PERMIT CENTER
Jos No. Joe NAME 7Ritl4 - IZ h
Eve r,>t tL enp - alp N E�
e S So A, LZ•
a S ifYN� Pf4 > ^ ;2;) ta'A fl'Mit'i ,TAr.R.;
Z = (%Z1X (3� — ( 73� (IY23 = I O,Y �C
u�1 LL 60a) 0/
2-
11/4)_ •96 /
10
1
ti
ENG I ItT.ERS - NORTH WEST NC. P.S.
• 6969 WOODLAWN AVE. N. E. - SUITE 205 - SEATTLE, WA 98115 - (206)525.7560 - FAX # (206) 527 -6698
DATE 6- •1 -q
SUOJECT SHEET
BY
OF
.{.S n.,
LOAD CASES
IOMENT AND DEFLECTION RESULTS +inwarc - outward
Case Pu (kips) Mu iin -k) Phi=Mn defi tin
INTERACTION CuRVE DATA
. ,7*PC ix :te 7xMnal x��
124.2 L:,: 105.8 33.1
(GINEERS-NORTHWEST CONCRETE.JAMB DESIGN (version 3.01
169 Mcodlawn Ave NE . 1988 UBC
3attle,Wasnington 98115 09:20:44 06 -14 -1996
po 100
0MB DATA height (ft) width (in) thickness lin) ada thickness iin) r. ;actor parapet ht (ft)
29.67 48.00 7.25 0.00 1.00 0.00
PANDREL DATA thickness(in) offset lin. + outward)
7.25 0.00
PENINGS LEFT wioth (ft) height (ft) RIGHT widtn ifti height (ft)
12.0 10.0 0.0 0.0
ATERIAL DATA concrete (psi) rebar (psi)
3000 60000 gtia. WPoZ
OADING DATA unfactored • -
wind in (psf) :. 0,0 cur ' i- Q'� cillcittru (
seismic... zone G Press 1osf1: import fact: 1.00
ledger Wolf): 600 DL ipif): 360 ecc fin): 0.5 % lL.► /seismic:
concentrated ion Lli )bs): 0 DL i )bsi: 10000 ecc (in): 0.0 % LL w /seismic: G
concentric laza Wolf): 0 DL (PM: 0 % IL wiseise11c: L
noriz loaa plf (+ inward): 0 dist above fioor(ft): 0.0
EBAR DATA
Vertical - $5 a: 3.62 Horizontal min in / it 0,17
Allow aefitini (,amments
Sheet of
STRNDER RETAIL
NEW DOOR 12;10 PNLS 50 s 52
1 5.1 77.8 56.29 -0,10 2.37 case c►.
2 6.1 - .: 56.29 -0.10 2.3 case ca
6.1 '7.8 56.25 -0.10 2.37 case ok
4 5.1 -11.0 60.15 -0.12 2.27 case of
5 8,1 -11.6 60.15 -0.12 2.37 case ok
5 7.1 - °.L 58.31 -0,10 2.31 case :f,
7 12.0 -20.2 63.00 -0.14 2.27 case used interaction clorve
11 .:UL - 1.2.111. inwarc NOTE it cases 1i. _ :, an:: _ the
21 .501 + 1.2wL outward • LL dse: is 112 of toe acc.iec LL
3) ,:DL + 1.43EQ
4i 1.0501 + 1.2SLL + 1.28W. inwarc
5) 1.OSD1 + 1,28LL . 1.28v. cutwarc
61 1.050L + 1.2SLL + i.4EQ
71 1.L10L + 1.7LL
CDC 462.
. nt.
u1n•
1/2
1/2
112
• 5/8
5/E
518
3/4
3/4
3/4
ENGINEERS NN Confidential
3
211V070
w3 1 w4 1 w5 I .lateral design 24.2
V = 3231
Page 1
H ft = 29.67 F'c= 3000
h ft = 12
wind = 24.20 psf
w1 ft = 5 siisaic 19.7 psf
w2 ft = 10 y1= 1
w3 ft = 4.0 r= 10
w4 ft = 0.0 y2= 1
e5ft =0
H/150 = 2.37
u = 217.80
C = 2988.32
T = 2370.86 M = 23709 SRItd1 = 7.05 SUM = 12
A,
;F,it. r = 32.80
INPUT TS MOMENT OF INERTI 75.10 -4,1841
r5
MEIIST _ 23966
NFL. = 1.74 55.17 MISOLATE= 2309:
ALLOWACLE DEFLECT 2.37 ?A?1 1 WIT:. STRONG BACK IS CK
MAX '. = 2988.3 TABS SASE
JERT 5" CLEAR PLATE
W10 IUSPEC BOLTS p: 6in.T0 EDGE 11SPEC B•ZLTS
F'CI:SI EMBED T allow RE8'11 ?L :hie:: '/ al REO'L
2 1/4 615 4.8E 9 0.204 1840 2.00
3 112 1000 2.99 3 0.204 1840 2.00
6 1080 2.77 i 0.204 1840 2,00
2 3/4 875 3.42 0.195 2875 2.00
r 1335 2.24 11 0.185 3125 2.00
7 1625 1.84 11 0.185 3125 2.00
3 1/4 1090 2.74 3.177 3E75 1.00
�4 4 A 4n'1C 1
314 4' T' 1. ,, 1i. 1..171 422J
8 2315 1.29 :2 0.177 4225 1.00
1D .J A.M.P,s
NI C#thNILlq,,, t1mt
ENG IF ERS— NORTH WESTC NC. :P. S.
6869 WOODLAWN AVE. N.E. - SUITE 205 - SEATTLE, WA 98115 - (206)525 -7560 -. FAX # (206) 522 -6698
Joe No.
JOB NAME 5kftr.i 1) R ►rttL. I 'L ' DATE
SUBJECT 6It? q•^ SHEET OF
BY
Loci c d Mcc t( AS SxowN
or to . joisi J., Joys,
41 i u ) AyLC P c t C� N COQ 6 M2,(4)
'2 rv, I ►J N, ' 630,3-0,\ O°
?u\-14S fioL IIIANfIt SolPG
c AitouN( opeA104 .
Extsi
‘joi3 it-ck&
E xls i 504
Dear Sir:
City of Tukwila
Fire Department Review
Control #B96 -0190
(512)
Fire Department Thomas P. Keefe, Fire Chief
July 24, 1996
Re: Old Navy Store - 300 Andover Park West, Suite #600
The attached set of building plans have been reviewed by
The Fire Prevention Bureau and are acceptable with the
following concerns:
1. The total number of fire extinguishers required for
your establishment is calculated at one extinguisher for
each 3000 sq. ft. of area.. The extinguisher(s) should be
of the "All Purpose" (2A, 10B:C) dry chemical type. Travel
distance to any fire extinguisher must be 75' or less.
(NFPA 10, 3 -1.1)
Extinguishers shall be installed on the hangers or in
the brackets supplied, mounted in cabinets, or set on
shelves (NFPA 10, 1 -6.9), and shall be installed so
that the top of the extinguisher is not more than 5
feet above the floor. (NFPA 10, 1 -6.9)
Extinguishers shall be located so as to be in plain
view (if at all possible), or if not in plain view,
they shall be identified with a sign stating, "Fire
Extinguisher ", with an arrow pointing to the unit.
(NFPA.10, 1 -6.3) (UFC Standard 10 -1)
Clear access to fire extinguishers is required at all
times. They may not be hidden or obstructed. (NFPA
10, 1 -6.5)
Fire extinguishers require monthly and yearly
inspections. They must have a tag or label securely
attached that indicates the month and year that the
inspection was performed and shall identify the
company or person performing the service. (NFPA 10,
John W. Rants, Mayor
Headquarters Station: 444 Andover Park East • Tukwila, Washington 98188 • Phone: (206) 575 -4404 • Fax (206) 5754439
City of Tukwila
Fire Department Thomas P. Keefe, Fire Chief
Page number 2
4 -3, 4 -4 and 4 -4.3) Every six years, dry chemical and
halon type fire extinguishers shall be emptied and
subjected to the applicable recharge procedures. (NFPA
10, 4 -4.1) If the required monthly and yearly
inspections of the fire extinguisher(s) are not
accomplished or the inspection tag is not completed, a
reputable fire extinguisher service company will be
required to conduct these required surveys. (NFPA
10A -4 -4)
Maintain fire extinguisher coverage throughout.
2. Exit doors shall be openable from the inside without
the use of a key or any special knowledge or effort. Exit
doors shall not be locked, chained, bolted, barred, latched
or otherwise rendered unusable. All locking devices shall
be of an approved type. (UFC 1207.3)
Obstructions, including storage, shall not be placed
in the required width of an exit, except projections
as permitted by the Building Code. Exits shall not be
obstructed in any manner and shall remain free of any
material or matter where its presence would obstruct
or render the exit hazardous. (UFC 1203)
Dead bolts are not allowed on auxiliary exit doors
unless the dead bolt is automatically retracted when
the door handle is engaged from inside the tenant
space.
Exit hardware and marking shall meet the requirements
of the Uniform Fire Code. (UFC 1207.1- 1212.8)
Internally illuminated exit signs shall have both
bulbs working at all times. (UBC 1013.3)
When two or more exits from a story are required, exit
signs shall be installed at the required exits and
where otherwise necessary to clearly indicate the
direction of egress. (UBC 1013.1)
John W. Rants, Mayor
Headquarters Station: 444 Andover Park East • Tukwila, Washington 98188 • Phone: (206) 575 -4404 • Fax (206) 575.4439
City of Tukwila
Fire Department
Page number 3
The color and design of lettering, arrows and other
symbols on exit signs shall be in high contrast with
their background. Words on the sign shall be block
letters 6 inches in height with a stroke of not less
than 3/4 inch. (UBC 1013.2)
Aisles leading to required exits shall be provided
from all portions of buildings. Aisles located within
an accessible route of travel shall also comply with
the Building Code requirements for accessibility.
(UFC 1204.1)
Exits shall be illuminated any time the building is
occupied with light having an intensity of not less
than 1 foot candle at floor level. Fixtures required
for exit illumination shall be supplied from separate
sources of power for Group I, Divisions 1.1 and 1.2
occupancies and for all other occupancies where the
exiting system serves an occupant load of 100 or more.
(UBC 1012.1, 1012.2)
When two or more exits from a story are required and
when two or more exits from a room or an area are
required by U.B.C. Section 3303, exit signs shall be
illuminated. (UBC 1013.3)
The power supply for the exit pathway illumination
shall normally be provided by the premise's wiring
system. In the event of its failure, illumination
shall be automatically provided from an emergency
system. Emergency system shall be supplied from
storage batteries or an on -site generator set and the
system shall be installed in accordance with the
requirements of the Electrical Code. (UBC 1012.2)
John W Rants, Mayor
Thomas P. Keefe, Fire Chief
Combustible material shall not be stored in exits or
exit enclosures. (UFC 1103.3.2.3)
Current supply to one of the lamps for exit signs
shall be provided by the premises' wiring system.
Power to the other lamp shall be from storage
Headquarters Station: 444 Andover Park East • Tukwila, Washington 98188 • Phone: (206) 5754404 • Fax (206) 5754439
City of Tukwila
Fire Department Thomas P. Keefe, Fine Chief
Page number 4
batteries or an on -site generator set and the system
shall be installed in accordance with the Electrical
Code. (UBC 1013.4)
3. All new sprinkler systems and all modifications to
existing sprinkler systems shall have fire department
review and approval of drawings prior to installation or
modification. New sprinkler systems and all modifications
to sprinkler systems involving more than 50 heads shall
have the written approval of the W.S.R.B., Factory Mutual,
Industrial Risk Insurers, Kemper or any other
representative designated and /or recognized by The City of
Tukwila, prior to submittal to the Tukwila Fire Prevention
Bureau. No sprinkler work shall commence without approved
drawings. (City Ordinance #1742)
Contact The Tukwila Fire Prevention Bureau to witness
all required inspections and tests. (UFC 10.503)
(City Ordinance #1742)
4. H.V.A.C. units rated at greater than 2,000 cfm require
auto - shutdown devices. These devices shall be separately
zoned in the alarm panel and local U.L. central station
supervision is required. (City Ordinance #1742)
All new fire alarm systems or modifications to
existing systems shall have the written approval of
The Tukwila Fire Prevention Bureau. No work shall
commence until a fire department permit has been
obtained. (City Ordinance #1742) (UFC 1001.3)
Call the Tukwila Fire Department at 575 -4407 for
approval of any system shut down. Have job site
address, name and the Tukwila Fire Department Job
Number available to confirm shut down approval. (City
Ordinance #1742)
5. All electrical work and equipment shall conform
strictly to the standards of The National Electrical Code.
(NFPA 70)
John W. Rants, Mayor
Headquarters Station: 444 Andover Park East • Tukwila, Washington 98188 • Phone; (206) 575 -4404 • Fax (206) 5754439
Page number 5
Yours truly,
cc: TFD file
ned
City of Tukwila
The Tukwila Fire Prevention Bureau
Fire Department Thomas P. Keefe, Fire Chief
6. Required fire resistive construction, including
occupancy separations, area separation walls, exterior
walls due to location on property, fire resistive
requirements based on type of construction, draft stop
partitions and roof coverings shall be maintained as
specified in the Building Code and Fire Code and shall be
properly repaired, restored or replaced when damaged,
altered, breached, penetrated, removed or improperly
installed. (UFC 701)
This review limited to speculative tenant space only -
special fire permits may be necessary depending on
detailed description of intended use.
Any overlooked hazardous condition and /or violation of the
adopted Fire or Building Codes does not imply approval of
such condition or violation.
John W. Rants, Mayor
Headquarters Station: 444 Andover Park East • Tukwila, Washington 98188 • Phone: (206) 5754404 • Fax (206) 575-4439
V.*
�0i4 'Am�n1AT yHiC Win+ +rn+..wv.ratot. u.*attra
Property service
6/28/96
James Furrate
1035 156th N.E.
Bellevue, WA.
Re : Old Navy Store
Tukwila, WA.
Dear Mr. Furrate,
Gary Palmer
Please find enclosed 3 sets of signed & sealed building plans
for submission to plan check, Building Permit Application,
Mechanical Permit Application, 3 sets of structural calculations,
mechanical forms, a check in the amount of $609.21 for payment
of plan check fees based on a BLDG. valuation of $110,000 and
mech. valuation of $48,000, check in the amount of $300.00 for
payment of your fee and a S.A.S.E. for return of any receipts
and paper work from plan check submission.
I checked plan review requirements for both electrical & plumbing
and was told that no plan review is required, could you please
verify that this is correct. I spoke with the Dept. of Labor
& Industries @ 206 - 248 -6630 for electrical and the King County
Health Dept., Eastgate Office @ 206 - 296 -9741 - Mike Bratcher.
All the information I have, including the plan check fee amount
was provided by Kelcie Perterson @ the Tukwila Building Dept.
phone ¢/ 206 - 431 -3672.
Thank you for all your help and if you have any questions, please
feel free to call.
JUL U 1 1996
PERMIT CENTER
Post Office Box 23767 • Pleasant Hill • California 94523 • (510) 825 -2940
Gary Palmer
RECEIVED
CITY OF TUKWILA
PLEASE DETACH AND SIGN
CERTIFICATE BEFORE PLACING
IN BILLFOLD
siGtiATORe':•-
ISSUED BY DEPA
igreg. //40:
vro • •
TMENT OF LABOR AND INDUSTRIES
•
. •
. RECE1"
CITY OF ;LIIONILA
AUG 0 7 C3
PERMIT CENTER
F625-052-000 (3-92)
•
cc
U i
1 ,
V W W W
J �I
a.
0
m o
co
cc
a_
i
ft
I
a i
a I
C)
U
C)
v
0
U
U
C)
10 t7' v 25'-
C
C
C
C
C
CIC
EXISTING WAREHOUSE BUILDING
TRAFFIC LANE
TRAFFIC LANE
Q EXISTING LEFT TURN LANE 8
TRAFFIC LANE
ATE
C
/
/ A/ xY
/ 4/ > / \ , /7
r
•
W/
,
/ i c2 ---
o - n
S LY .. 11 '
/ J UST BLOCKING
/ /, ' • l
:IST1NG WAREHOUSE BUILDING
TRAFFIC LANE
TRAFFIC LANE
' EXISTING LEFT TURN LANE P
TRAFFIC LANE
= E
b
011 J
if /THRUST BLOCKING
I I
CIClC�Cicic ClC
0
CAUTION:
THE CONTRACTOR SHAD. EXCF.RSIZE EXTREME CARE To
NOT DLS THE D L AND UTILITY SYS EMS
INSTALLING iroR
THIS BUILDING. EXISTING 8' WATERYAIN
A
DER I3LVD-
TENANT A
W /BOx
•
1 -80 TAPPING
EXTREME CARE TO
GASINE mint
SYSTEMS FOR
STING Er WATERYAIN
11/2"
W /BOX
TENANT A
w /BOX
•
1- 8 TEE
1..._
1 -r GATE VALVE, YJ
1- 12" X8" REDUCER, U
W/THRUST • BLOCKING
•
<if] 1 3. - -
1- 12'X8" REDUCER, MJA'
1 -8 TEE, FL
2- 8"GATE VALVE, FLXMi
W/THRUST BLOCKING
1
LOCKING
r
C
EXISTING OFFICE
BUILDING
VICINITY MAF
NTs
VICINITY MAP
NTS
..;
SITE
I;
VI 0
21.1: L�
v ,�
FINISH FLOO
FINISH GRAD
�pe wink
1NS7�LL
(z) I %Z" WA7ee. MSS
IN XK771`4r Oj?C
CALL PVAIER. p(PrNZT
LaMPL�T�17 UN P��
�AviA? POW, t7"'
i'wg4- cr �
17LF OF 6" DI PIPE
11 /2
w /BOX
W
U
0.
z
w
Itc
PRIVATE DRIVE
UNDER- 5EP?4TE
PERM
SITE PLAN
MI '16 0006
1 -11'X1 X
1 -8' GATE
1 -12 - GATE
W/THRUST
e oP kyckk_
(2.) Ire vvAze
X('371tr METE ecx
wActoe. P(PN4-
pLv Ut-42e12.
ApA- Pew tr
q4-cezr)
12 PIPE (Cuss 52)
SITE PLAN
MI 0006
TENANT C
11/2
W/BOX
1-12 TEE, FL
1-13 VALVE,
1 12 VALVE,
W/THRUST BLOCKING
Er FIREMAN W
P 02 11 4 E
FINISH FLOOR 27.50
FINISH GRADE 26.50
/
"ry OF a' 1 PIPE (CLASS 52)
AA010
1
W /BOX
6 PIPE (CLASS 52) +
STORM DRAINAGE
SYSTEM-SEE SHEET 2E
1-12 MI
THRUST BLOCKING
TENANT B
)7 (TYP)
<1.
TRECK DRIVE
Y
BUILDINC
CATED WATER KETERS/PRV STATIONS AS PER APPLI
WATER SYSTEM REVISIONS AS PER THE CITY OF
REDESIGN SANITARY SEWER SYSTEM AS PER APPLI
A MINOR GENERAL REVISION'S BY THS APPLICANT 08/3
1-± WATER SYSTEM REVISIONS AS PER THE CITY OF
2E
J.
i
(T
W
OF NIS PIPE (CLASS 52)
A
6" DI PJP-E
Kiva 15.
BUILDING
+
CATED WATER METERS /PRV STATIONS AS PER APPLICANT 09/90/94
WATER SYSTEM REVISIONS AS PER THE CITY OF TUKWILA 09/21/93
REDESIGN SANITARY SEWER SYSTEM AS PER APPLICANT 09/11/93
ICNOR GENERAL REVISIONS BY THE APPLICANT 08/31/93
WATER SYSTEM REVISIONS AS PER THE CITY OF TUKWILA 07/21/93
115 F."V DIRECT- BURY
INSTALLATION LIMIT
CITY OF TUKWILA'S APPROVAL
THIS PLAN IS APPROVED FOR CONFORMANCE
WITH THE CITY OF TUKWILA' S REQUIEMENTS,
SPECIFICATIONS AND STANDARDS, AND
CAN BE USED FOR CONSTRUCTION OP THE
IMPROVEMENTS SHOWN HEREON.
APPROVED BY
DATE APPROVED:
CONSTRUCTION NOTES~
1. ALL WORKMANSHIP AND MATERIALS SHALL CON?
TUKWIIA'S REQUIREMENTS AND SPECIFICATIONS. TE
SHALT. MEET, OR EXCEED, CITY OF TUKWILA STAND
2. THE CONTRACTOR SHAM. INSTALL. THE WATER Al
IN ACCORDANCE WITH THE CITY OF TUKWIIA'S STA
TYPE OF HYDRANTS, VALVES, BEDDING MATERIAL, I
COMPACTION DEGREE, CLEANOUT CONSTRUCTION, T
METHODS, ETC.. +
3. THE CONTRACTOR SHALL. CONSTRUCT THE LAND:
AS PER THE CITY'S STANDARDS WITH DSHS APPRO
VALVE AND EXEMPT METER. THE SYSTEM AND MET
TO BE DETERMINED.
4. ALL WATERMAINS SHAM. BE DUCTILE IRON PIPE
MINIMUM COVER OF 42 INCHES (42").
CAI
S
V
UCT1ON NOTES
MI 9600b6
ORK1UNSHIP AND MATERIALS SHALL CONFORM TO THE CITY OF
'3 REQUIREMENTS AND SPECIFICATIONS. THE UTILITY CONSTRUCTION
OR EXCEED, CITY OF TUKWILA STANDARDS.
CONTRACTOR SHALL INSTALL THE WATER AND SEIrER SYSTEMS
RDANCE WITH THE CITY OF TUKWIL&•s STANDARDS, INCLUDING
HYDRANTS, VALVES, BEDDING MATERIAL, BACKFILL MATERIAL,
ON DEGREE, CLEANOUT CONSTRUCTION, THRUST BLOCKING, TESTING
s, ETC.. +
CONTRACTOR SHALL CONSTRUCT THE LANDSCAPE IRRIGATION SYSTEM
THE CITY'S STANDARDS WITH DSHS APPROVED DOUBLE —CHECK
EXEMPT METER. THE SYSTEM AND METER LOCATION IS YET
$rERM NED.
WATERMAINS SHALL BE DUCTILE IRON PIPE (CLASS 52) 1fITH A
COVER OF 42 INCHES (42').
These plans have been reviewed by the Public
Works Department for conformance with current
City stancords. Acceptance is subject to errors
and oml:sior �s which do not authorize violations of
adopted standards or ordinances. The responsibility
for the adequacy of the design rests totally with
the designer. Additions, deletions or revisions to
these drawings after this date will void this
acceptance and will require a resubmittal of
revised drawings for subsequent approval.
Final acceptance is subject to field inspection by
the Public Works utilities inspector.
Date: c7 / t By:
PERMIT CENTER
fi
CAD FILE NAME: STRAND7.DRG XREF = STRAND4 /201
SEGALE RETAIL CENTER
SO Mt
WATER AND SERER PLAN
Z
RECEIVED
SEP - 91996
TUKWILA
PUBLIC WORKS
RECEIVED
CITY OF TUKWILA
SEP 0 9 1996
MA SEGALE INC.
TUKWILA, WASHINGTON pas) rm
3 .10
nsasna xwaEe
201 --93XXX