HomeMy WebLinkAboutPermit M05-199 - CHURCH BY THE SIDE OF THE ROADCHURCH BY THE SIDE OF
THE ROAD
3455 S 148 ST
Parcel No.: 0041000122
Address: 3455 S 148 ST TUKW
Suite No:
Value of Mechanical: $2,540.00
Type of Fire Protection:
City Tukwila
Tenant:
Name: CHURCH BY THE SIDE OF THE ROAD
Address: 3455 S 148 ST, TUKWILA WA
Owner:
Name: CHRUCH BY THE SIDE OF THE ROAD
Address: PO BOX 68545, SEATTLE WA
Contact Person:
Name: ROBERT MCNEELY
Address: 230 COUNTY LINE RD SW, PACIFIC WA
Contractor:
Name: SKILFAB SHEET METAL CO
Address: 230 COUNTY LINE RD SW, PACIFIC, WA
Contractor License No: SKILFSM169RE
DESCRIPTION OF WORK:
EXTEND DUCT THRU NEW ROOF AND WRAP W/ DUCT WRAP AND INSTALL EXISTING FAN
Furnace: <100K BTU
>100K BTU
Floor Furnace
Suspended /Wall /Floor Mounted Heater
Appliance Vent
Repair or Addition to Heat /Refrig /Cooling System....
Air Handling Unit <10,000 CFM
>10,000 CFM
Evaporator Cooler
Ventilation Fan connected to single duct
Ventilation System
Hood and Duct
Incinerator: Domestic
Commercial /Industrial
doc: IMC- Permit
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206- 431 -3670
Fax: 206 - 431 -3665
Web site: ci.tukwila.wa.us
MECHANICAL PERMIT
Permit Number:
Issue Date:
Permit Expires On:
EQUIPMENT TYPE AND QUANTITY
0
0
0
0
0
0
0
0
0
1
0
0
0
0
* *continued on next page **
M05 -199
Phone:
Phone: 253 333 -0014
Phone: 253 333 -0014
Expiration Date:12 /13/2006
Steven M. Mullet, Mayor
Steve Lancaster, Director
M05 -199
01/17/2006
07/16/2006
Fees Collected: $191.18
International Mechanical Code Edition: 2003
Boiler Compressor:
0 -3 HP /100,000 BTU 0
3 -15 HP /500,000 BTU 0
15 -30 HP /1,000,000 BTU.. 0
30 -50 HP /1,750,000 BTU.. 0
50+ HP /1,750,000 BTU 0
Fire Damper 0
Diffuser 0
Thermostat 0
Wood /Gas Stove 0
Water Heater 0
Emergency Generator 0
Other Mechanical Equipment
Printed: 01 -17 -2006
• 0
u, o
w w
W O
g Q
rn .
d•
? ;
I— O
Z
w W
co
O—
01–
w cu
1–
U
L O
z
0 -.
Permit Center Authorized Signature: J I/ VIA
I hereby certify that I have read and ihed.this permit and know the same to be true and correct. All provisions of law and
ordinances governing this work will be complied with, whether specified herein or not.
The granting of this permit does
regulating constru ,,;uT�" he pe
Print Name: a �v
City 671, Tukwila
t presume t
Signatur -. P "' ,
doc: IMC- Permit
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206-431-3670
Fax: 206 - 431 -3665
Web site: ci.tukwila.wa.us
Steven M. Mullet, Mayor
Steve Lancaster, Director
Permit Number: M05 -199
Issue Date: 01/17/2006
Permit Expires On: 07/16/2006
Date: D 1 ' h- -C( v
ority to violate or cancel the provisions of any other state or local laws
uth zed to sign and obtain this mechanical permit.
Date: /"--/ ? "'!� ,, �f (/�
This permit shall become null and void if the work is not comme ced within 180 days from the date of issuance, or if the work is
suspended or abandoned for a period of 180 days from the last inspection.
M05 -199 Printed: 01 -17 -2006
.
.gi
W •
;J
N LL,
W O }
N
d•
' 2 ILE
D p
ww
• 1- V'
O:
z
.0 1,.
•
City of Tukwila
Department of Community Development / 6300 Southcenter BL, Suite 100 / Tukwila, WA 98188 / (206) 431 -3670
Parcel No.: 0041000122 Permit Number: M05 -199
Address: 3455 5 148 ST TUKW Status: ISSUED
Suite No: Applied Date: 12/19/2005
Tenant: CHURCH BY THE SIDE OF THE ROAD Issue Date: 01/17/2006
1: ** *BUILDING DEPARTMENT CONDITIONS * **
PERMIT CONDITIONS
2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the
Building Official.
3: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to
start of any construction. These documents shall be maintained and made available until final inspection approval is
granted.
4: Readily accessible access to roof mounted equipment is required.
5: All construction shall be done in conformance with the approved plans and the requirements of the International
Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code.
6: Manufacturers installation instructions shall be available on the job site at the time of inspection.
7: All plumbing and gas piping work shall be inspected and approved under a separate permit issued by the Department of
Public Health - Seattle and King County (206/296- 4932).
8: All electrical work shall be inspected and approved under a separate permit issued by the Washington State Department
of Labor and Industries (206/248- 6630).
9: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of,
any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits
presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila
shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the
Building Official from requiring the correction of errors in the construction documents and other data.
10: ** *FIRE DEPARTMENT CONDITIONS * **
11: The attached set of building plans have been reviewed by the Fire Prevention Bureau and are acceptable with the
following concerns:
12: A Type 1 hood shall be installed at or above all commercial cooking appliances and domestic cooking appliances used for
commercial purposes that produce grease vapors. Each required commercial kitchen exhaust hood and duct system required
by section 610 of the International Fire Code to have a Type 1 hood shall be protected with an approved automatic
fire- extinguishing system installed in accordance with this code. (IFC 610.2, IFC 904.2.1 and IFC 904.11)
13: An approved automatic fire- extinguishing system is required for this project.
14: All new automatic fire- extinguishing systems and all modifications to existing automatic fire- extinguishing systems
shall have fire department review and approval of drawings prior to installation or modification.
15: Local U.L. central station supervision is required. (City Ordinance #2051)
doc: Conditions
M05 -199
Printed: 01 -17 -2006
•
City of Tukwila
Department of Community Development / 6300 Southcenter BL, Suite 100 / Tukwila, WA 98188 / (206) 431 -3670
16: Portable fire extinguishers shall be provided within a 30 -foot (9144 mm) travel distance of commercial -type cooking
equipment. Cooking equipment involving vegetable or animal oils and fats shall be protected by a Class K rated portable
extinguisher. (IFC 904.11.5)
17: Contact The Tukwila Fire Prevention Bureau to witness all required inspections and tests. (City Ordinances #2050 and
#2051)
18: Any overlooked hazardous condition and /or violation of the adopted Fire or Building Codes does not imply approval of
such condition or violation.
19: These plans were reviewed by Inspector 511. If you have any questions, please call Tukwila Fire Prevention Bureau at
(206)575 -4407.
doc: Conditions
* *continued on next page **
M05 -199
Printed: 01 -17 -2006
City of Tukwila
Department of Community Development / 6300 Southcenter BL, Suite 100 / Tukwila, WA 98188 / (206) 431 -3670
I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and ordinances
governing this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provision of any other work or local laws
regulating construction or the performance of • k.
4 � - Signature: � % ( Date: l� /
Print Name:
doc: Conditions
M05 -199 Printed: 01 -17 -2006
1
Site Address:
Name:
E -Mail Address:
CITY OF TUKWILA
Community Developmen partment
Public Works Department
Permit Center
6300 Southcenter Blvd., Suite 100
Tukwila, WA 98188
3w,1�".rjb. 5 - qsf
Tenant Name: CI u (ZEE p j • - t id-j
Property Owners Name: L _ , r - <0 °
Mailing Address: rl L 1T x64 - 5"
Mailing Address: — 273 SO U
q: \\permits plus\icc chant{es\permit application (7.2004)
Revised: 6-I-05
bh
Building Perri. 1 vo
Mechanical Permit No
Public Works Permit No: r( .
Project No
(For office use only)
Applications and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or by fax.
* *Please Print **
King Co Assessor's Tax No.: 2D1..1 OgaD
Suite Number: Floor:
• -. / / • • it':.b
Moe
/y/%v ed 5w .
Contact Person:
E -Mail Address:
Contact Person:
E -Mail Address:
Contact Person:
E -Mail Address:
Page 1
New Tenant: ❑ .... Yes No
City
Slate Zip
d o- I D Telephone: '?,.mot ` '"'a '/ -
Slate Zip
Fax Number: "2 -e0 7
City
GENERAL CON RACTOR INFORMATION - ' (Mechanical Contractor information on back page)
Name:
Mailing Address:
City
Day Telephone:
Fax Number:
Slate
Zip
Contractor Registration Number: Expiration Date:
* *An original or notarized copy of current Washington State Contractor License must be presented at the time of permit issuance **
ARCHITECT: OF RECORD — All plans must be wet stamped by Architect of Record
Company Name:
Mailing Address:
Zip
City
Day Telephone:
Fax Number:
State
ENGINEER OF RECORD -,:'411 plans must be wet stamped by Engineer of Record
Company Name:
Mailing Address:
City
Day Telephone:
Fax Number:
State
Zip
Valuation of Project (contractor's bid price): $ Existing Building Valuation: $
Scope of Work (please provide detailed information):
Will there be new rack storage? ❑ ..Yes ❑.. No If "yes ", see Handout No. for requirements.
Provide All Building Areas in Square Footage Below
PLANNING DIVISION:
Single- family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches)
For an Accessory dwelling, provide the following:
Lot Area (sq ft): Floor area of principal dwelling: Floor area for accessory dwelling:
*Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence.
Number of Parking Stalls Provided: Standard:
Compact: Handicap:
Will there be a change in use? ❑ ....Yes ❑ ..No If "yes ", explain:
FIRE PROTECTION/HAZARDOUS MATERIALS:
❑ .. Sprinklers ❑..Automatic Fire Alarm ❑..None ❑ . Other (specify)
Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ .. Yes ❑ ..No
If "yes", attach list of materials and storage locations on a separate 8 -1/2 x 11 paper indicating quantities and Material Safety Data Sheets.
q: \\permits plus \ice chanl{es \permit application (7.2004)
Revised 6.405
bh
Page 2
Existing ..
Interior
Remodel
Addition to
Existing
Structure
New
Type of
Construction
per IBC
Type of
Occupancy per
IBC
1" Floor
2" Floor ,.
3 Floor
Floors thru
Basement
Accessory Structure*
Attached Garage
Detached Garage ..
Attached Carport
.
Detached Carport :. .
Covered. Deck
Uncovered Deck
Valuation of Project (contractor's bid price): $ Existing Building Valuation: $
Scope of Work (please provide detailed information):
Will there be new rack storage? ❑ ..Yes ❑.. No If "yes ", see Handout No. for requirements.
Provide All Building Areas in Square Footage Below
PLANNING DIVISION:
Single- family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches)
For an Accessory dwelling, provide the following:
Lot Area (sq ft): Floor area of principal dwelling: Floor area for accessory dwelling:
*Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence.
Number of Parking Stalls Provided: Standard:
Compact: Handicap:
Will there be a change in use? ❑ ....Yes ❑ ..No If "yes ", explain:
FIRE PROTECTION/HAZARDOUS MATERIALS:
❑ .. Sprinklers ❑..Automatic Fire Alarm ❑..None ❑ . Other (specify)
Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ .. Yes ❑ ..No
If "yes", attach list of materials and storage locations on a separate 8 -1/2 x 11 paper indicating quantities and Material Safety Data Sheets.
q: \\permits plus \ice chanl{es \permit application (7.2004)
Revised 6.405
bh
Page 2
,pope WORKS PERMIT IN iMATION
Scope of Work (please provide detailed information):
Water District
❑ ...Tukwila 0... Water District #125
❑ ... Water Availability Provided
Sewer District
❑...Tukwila ❑... ValVue ❑ .. Renton ❑ ...Seattle
❑ ...Sewer Use Certificate 0... Sewer Availability Provided ❑ .. Approved Septic Plans Provided
❑ ...Septic System - For onsite septic system, provide 2 copies of a current septic design approval by King County Health Department.
Submitted with Application (mark boxes which apply):
❑ ...Civil Plans (Maximum Paper Size — 22" x 34 ")
❑ ...Technical Information Report (Storm Drainage)
❑ ...Bond ❑ .. Insurance ❑ .. Easement(s)
Proposed Activities (mark boxes that apply):
❑ ...Right -of -way Use - Nonprofit for less than 72 hours
❑ ...Right -of -way Use - No Disturbance
❑ ...Construction/Excavation/Fill - Right -of -way
Non Right -of -way
❑ ...Total Cut
❑ ...Total Fill
cubic yards
cubic yards
❑ ...Sanitary Side Sewer
❑ ...Cap or Remove Utilities
❑ ...Frontage Improvements
❑ ...Traffic Control
❑ ...Backflow Prevention - Fire Protection
Irrigation
Domestic Water
❑ ...Permanent Water Meter Size...
❑ ...Temporary Water Meter Size ..
❑ ...Water Only Meter Size
❑ ...Sewer Main Extension Public
❑ ...Water Main Extension Public _
6:\\•ertnita pk s \icc changea\permit application (7 -2004)
Revised: 64.05
bh
Call before yotl Dig: 1- 800 - 424 -5555
Please refer to Public Works Bulletin #1 for fees and estimate sheet.
r,
If
f f
❑ .. Abandon Septic Tank
❑ .. Curb Cut
❑ .. Pavement Cut
❑ .. Looped Fire Line
If
It
11
WO#
WO#
WO#
Private
Private
6- 433= 0179''
❑ .. Highline ❑ ...Renton
❑ .. Geotechnical Report ❑...Traffic Impact Analysis
❑ .. Maintenance Agreement(s) ❑...Hold Harmless
❑ .. Right -of -way Use - Profit for less than 72 hours
❑ .. Right -of -way Use — Potential Disturbance
❑ .. Work in Flood Zone
❑ .. Storm Drainage
Page 3
❑ .. Grease Interceptor
❑ .. Channelization
❑ .. Trench Excavation
❑ .. Utility. Undergrounding
❑ ...Deduct Water Meter Size
FINANCE INFORMATION
Fire Line Size at Property Line
❑ ...Water ❑ ...Sewer ❑ ...Sewage Treatment
Monthly Service Billing to:
Name:
Mailing Address:
Number of Public Fire Hydrant(s)
Water Meter Refund/Billing:
Name:
Mailing Address:
Day Telephone:
City State Zip
Day Telephone:
City
State
Zip
Unit Type:
Qty
Unit Type:
Qty
Unit Type:
Qty
Boiler /Compressor:
Qty
Furnace <100K BTU
Air Handling Unit >10,000
CFM
Fire Damper
0 -3 HP /100,000 BTU
Fumace>100K BTU
Evaporator Cooler
Diffuser (
3 -15 HP /500,000 BTU
•
Floor Furnace
Ventilation Fan Connected
to Single Duct
r
1
Thermostat
I5-30 HP /1,000,000 BTU
Suspended /Wall/Floor
Mounted Heater
Ventilation System
Wood /Gas Stove
30 -50 HP /1,750,000 BTU
Appliance Vent
Hood and Duct
Water Heater
50+ HP /1,750,000 BTU
Repair or Addition to
Heat/Refrig/Cooling
System
Incinerator - Domestic
Emergency
Generator
Air Handling Unit
<10,000 CFM
Incinerator – Comm/Ind
Other Mechanical
Equipment
MECHANICAL PERMIT INFCflyIATION - 206. 431 -3670
MECHANICAL CON
Company Name:
Mailing Address:
Contact Person:
E -Mail Address:
Contractor Registration Number: 5 e 4 5l>/(0� PLC-- Expiration Date: 1 Z•� - 1 '"3
* * An original or notarized copy of current State Contractor License must be presented at the time of permit issuance **
Valuation of Project (contractor's bid price): $ 7 5 4Oo 1242
Scope of Work (pl se rovide d tailed information): :, •
wbAIJ w c v D4 W � .fix I
Print Name:
r ' TO ' INF S
•
RMAT
Use: Residential: New Replacement....:
Commercial: New ....❑ Replacement
Fuel Type: Electric ❑ Gas... Other:
Indicate type of mechanical work being installed and the quantity below:
PERMIT APPLICATION. NOTES - Applicable to all permits in this application
Value of Construction – In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject
to possible revision by the Permit Center to comply with current fee schedules.
Expiration of Plan Review – Applications for which no permit is issued within 180 days following the date of application shall expire by limitation.
The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be requested
in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition).
I HEREBY CERTIFY THAT 1 HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER
PENALTY OF PERJURY BY THE LAWS r:. E STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT.
BUILDING OWN %' U ! • • D AGENT
Signature.
sr
Mailing Address: '273!9 --C,4At
(4/
Page 4
w
City State Zip
Day Telephone: x'3`3 O(
Fax Number: '- .j .-_3 -- 6577
City
.Date: 2-'" /7 -ar
hone: 2-.5 �� --OCR/ 7
'/2r0
State
State Zip
Date Application ccepted: D ate Application xpires: Staff Initials:
r 9 / 05 o� /9 (e �w
q:\ \permits plus\icc changes\permit application (7.2004)
Revised 6.5.05
bh
1
City of Tukwila
6300 Southcenter BL, Suite 100 / Tukwila, WA 98188 / (206) 431 -3670
Parcel No.: Permit Number: M05 -199
Address: 3455 5148 ST TUKW Status: PENDING
Suite No: Applied Date: 12/19/2005
Applicant: CHURCH BY THE SIDE OF THE ROAD Issue Date:
Receipt No.: R05 -01813 Payment Amount: 191.18
Initials: LAW Payment Date: 12/19/2005 02:28 PM
User ID: 1630 Balance: $0.00
Payee: SKILFAB SHEETMETAL CO
TRANSACTION LIST:
Type Method Description
doc: Receipt
Payment Check 26230
ACCOUNT ITEM LIST:
Description
MECHANICAL - NONRES
PLAN CHECK - NONRES
RECEIPT
Amount
191.18
Account Code Current Pmts
000/322.100 158.94
000/345.830 32.24
Total: 191.18
0395 12/19 9 716 TOTAL .191.18
Printed: 12 -19 -2005
W
c)§:
co w
t u 0
g
u-4'
g.
O
111 iu;
j 0;
ON
.0 IN,
:IL 111.
ti '
O .
W N ~
Z
Projec : 1
Type of Inspection:
Address:
..ys5 S. /yg.t
Date Called:
Special Instructions:
Date Wanted:
/0 — /6 - 0 .
a.m.
p,m.
Requester:
Phone No:
?Olo 2 /3 - 5 0 -?9
INSPECTION RECORD
Retain a copy with permit
//2 es 5 '/1 �7
INSPECTION NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -36
PERMIT NO.
Approved per applicable codes. El Corrections required prior to approval.
COMMENTS:
" ;)4e
0 $58.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call to sechedule reinspection.
'Receipt No.:
'Date:
Project: /
l 4, IDYL el ‹, ?,4 �
Type of Inspection:
(
�--
/ r >?
Address: ^�
•3 /y8
Date Called:
Special Mt
ions:
Date Wanted: /
! )--
/ � /J!
�`�
a.m.
<O:m.
Requester:
Phone No:
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188
Approved per applicable codes.
PE
)43 -360
Corrections required prior to approval. 1/
COMMENTS:
GI
S C - e l
ii
1-1-0 ;/ / e K.; 4,y
cl%! r,Gr
/
$58.00 REINSPECTION EE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call to sechedule reinspection.
Receipt No.:
IDate:
Project:
(ihi / y (P ht- ;` C .
'Type of Inspection:
n:
- 7--
-�- (.
Address: . 1
y37,5 /y esi -
Date Called:
Special In st r uctions: .
_
Date Wanted
-2G- CC
a.m:
Requester:
Phone No:
INSPECTION RECORD
Retain a copy with permit
ON NO. PERM)
CITY OF TUKWILA BUILDING DIVISION i
6300 Southcenter Blvd., #100, Tukwila, WA 98188 . (206)431 -367
Approved per applicable codes. Corrections required prior to approval.
COM NTS:
j (4 r✓ / -¢, .s i— * ".
/7
I DatL /_ 2 —off
8.00 REINSPECTIO FEE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcen r Blvd., Suite 100. Call to sechedule reinspection.
'Receipt No.:
'Date:
W '
UO:
u)
our
U.
w C)
Z °
W
o
•C)
t-
w'
1- V
~ O
Z
U N:
O'
Proj ct: :
0 6
Type of Inspection: _
Address:
2 Li55 g . ► yo
Date Called:
Special I stru tions:
v� jt
!ice
3 3 3 0 h• i,
°0/9
Date Wanted:
LI - - W -- O,
Requester:
Phone No:
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188
Approved per applicable codes. Corrections required prior to approval.
nspec
e
i • No. :.
D te:
PERMI� 1
,
(206)431 -367
� Date:
$58. ' 0 REINSPECTION FEE REQUIRE Prior to ins ction, fee must be
pal. at 6300 Southcenter Blvd., Suite 00. Call to chedule reinspection.
7v
0O
y 0
ro w;
W O.
u_Q
Na
W.
Z
LU:
gft
S
W W .
U.
li z ;
O
Project: � �
�r. .Ire
Type of I �ec on:
�
.-
Address:
Date, Ca �d; •
Special Instructions:
, -r_3 3 i
--� /
Date Wanted]
ra.k,
ir
Requester:
Phone No:
� -
x3-5
.9
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188
PER
(206)431 -367
Approved per applicable codes. 0 Corrections required prior to approval.
CO ENTS:
El $58.00 REINSPECTION TEE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call to sechedule reinspection.
Receipt No.:
1 Date:
•
Z
re 2
u
0 LL:
w
<
P. d
H O
z I—
uj
0 1-
w w ;.
LL Z
V N ,
0
Application
Fire
Resistive
Rating
Enclosure System
Through
Penetration
System
Grease Ducts
1 or 2
hours
1 layer, 11/2' FastWrap +, perimeter
and longitudinal overlap 3" (75
GD 544 F, GD 562 F, UL G-14
OPL FS 587F
UL C -AJ -7098
Air Ducts
2 hours
1 layer, 11/2" FastWrap +, perimeter
and longitudinal overlap 3"
(75 mm), UL V -19
C -AJ -7095,
UL -W -L -7121
UL -F -C -7036
FireMaster Product
Unit
Size
Units/
Ctn.
Wt./
Ctn.
FastWrap+
Roll
11/2" x 24" x 25'
(38.1 mm x 610 mm x 7.6 m)
1
37.5 lbs.
(17 kg)
FastWrap+
Roll
11/2" x 48" x 25'
(38.1 mm x 1.2 m x 7.6 m)
1
75 lbs.
(34 kg)
FastWrap+ Collar
Roll
11/2" x 6" x 25'
(38.1 mm x 152 mm x 7.6 m)
4
53 lbs.
(24 kg)
Color
White blanket with silver foil encapsulation
Tremco Inc.
Fyre Sil sealant or Fyre -Sil S/L
Sealant (for floor assemblies
only)
Specified Technologies Inc.
Pensil 300
Rectoseal
835+ Sealant
HILTI Construction Chemicals,
Division of HILTI Inc.
FS One Sealant
Flammability (ASTM # 84 /UL 723)
Foil:
Flame spread
5
Smoke developed
10
Blanket:
Flame spread
0
Smoke developed
0
Thermal Resistance
R value per ASTM C 518
4.15 per inch at 70 °F (21°C)
fI
R
Fire Protection Systems
Product Data and Installation Guide
6 e. � .
RAT°
NFPA 96 IMC
1. Product Description - New and Improved FastWr
Thermal Ceramics new and improved FireMaster Fast
one - layer, totally foil - encapsulated, non - combustibl
(1093 °C) rated, low biopersistence, flexible fireproofing wrap specif-
ically tested to provide a 1 or 2 hour fire rated enclosure for hori-
zontal and vertical commercial kitchen grease and air ventilation
ducts. The core blanket chemistry is alkaline -earth silicate wool free
of binders and lubricants. FastWrap+ is classified by Omega Point
Laboratories and Underwriter's Laboratories Listing and Follow -up
Service Program to ensure uniform thickness and density specifica-
tions, thus providing consistency in end physical properties for
required fire ratings. FastWrap+ is a proven performance alterna-
tive through extensive testing to 1 or 2 hour fire - resistance rated
shaft enclosures. With its excellent insulating capability of with-
standing fire condition temperatures up to 2000 °F (1093 °C), it pro-
tects combustible constructions at zero clearance throughout the
entire enclosure system. When the duct penetrates fire rated walls
and floors, an approved silicone firestop sealant used in combina-
tion with FastWrap+ provides an alternate means of protection to
rigid shafts by maintaining the integrity of the 1 or 2 hour fire rated
wall and floor assembly. FireMaster FastWrap+ is resistant to mold
growth in test conditions of 75 -95% relative humidity (ASTM
D6329).
Product Features
• One -layer system with 3 optional installation techniques
• Low biopersistent insulation blanket
• Does not contain low temperature fiberglass or mineral wool
• Shaft alternative to rigid board systems
• Zero clearance to combustibles protection throughout the entire
enclosure system
• Lightweight, flexible wrap saves labor
• Passive fire proof material does not shrink, become brittle, or
lose fire fighting capabilities with age
• Totally foil encapsulated system protects against material degra-
dation, and potential fire hazards
• Product markings on foil ensure proper material identification for
easy inspections
• Wide variety of through - penetration systems
• Resistant to mold growth
2. Applications
• 1 or 2 Hour Commercial Kitchen Grease Duct Enclosure
• 1 or 2 Hour Air Ventilation Duct Enclosure
FILEw
Permit No.
_VAMP
l Ceramics
Thermal Ceramics
JAN 112006
RECEIVED
CITY OF TUKWILA
DEC 19 2005
PERMIT CENTER
FastWrap+ 1
Commercial Kitchen Grease Duct
Air Ventilation Duct
3. Physical Characteristics
4. Specifications
This specification guide covers the application of Thermal Ceramics
FireMaster FastWrap+ and An approved silicone firestop sealant.
5. Performance
A. Thermal Ceramics FireMaster FastWrap+
B. Fire Stop Sealants
Agency
Reference Standard /File No.
Omega Point Laboratories, Inc,
Listing # 11660 -3
Underwriters Laboratory
Grease Duct Enclosures (YYET):
R14229; Fire Resistive Ventilation Duct
Assemblies (HNJL): V -19; Through -
Penetration FireStop System (XHEZ):
C -AJ -7095, C -AJ -7098
NFPA
Complies with NFPA 96, 2001 Edition
International Mechanical Code
Section 506.10.3 Commercial Kitchen
Grease Ducts and Exhaust Equipment,
Section 507 Commercial Kitchen Hoods,
2003 Edition
New York MEA
412 -02 -M, 413-02-M
International Code Council
SBCCI Legacy Report No. 9424E
BOCA Legacy Report No. 22.25
City of Los Angeles
RR8425
California State Fire Marshal
2440 - 1361:103
2440 - 1361:105
C. Listings
6. Installation
A qualified contractor in accordance with manufacturer's instruc-
tions and referenced standards shall install the new or original
FireMaster FastWrap+ system using the installation methods as
described in sections A -D. See Figures 1 - 4 complete drawing
details.
Materials and Equipment:
FireMaster FastWrap+ blanket, 11/2" (38.1 mm) thick, 6 pcf (96
kg /m 24" (600 mm), or 48" (1.2 m) wide, and 25' (7.6 m) long rolls;
optional 6" wide x 20' long (150 mm x 6 m) rolls
• FireMaster FastWrap +: 25' (7.6 m) standard length, 48" (1220
mm) wide blanket helps to minimize waste
• Aluminum foil tape
• Minimum 3 /4" (19.0 mm) wide filament tape (optional)
• Carbon steel or stainless steel banding material, minimum 1/2"
(12.5 mm) wide, minimum 0.015" (0.38 mm) thick, with steel
banding clips
• Hand banding tensioner and crimping tool
• Minimum 12 gage steel insulation pins; galvanized steel speed
clips, minimum 11/2" (38 mm) x 11/2" (38 mm) square or 11/2" dia.
(38 mm), or equivalent sized cup -head pins; capacitor discharge
stud gun
• Access door hardware: four galvanized steel threaded rods, 1 /4"
diameter (6.35 mm) by 4 to 5" long (114 to 127 mm) with ' /4"
(6.35 mm) wing nuts and 1/4" (6.35 mm) washers; 4" (102 mm)
long steel tubing to fit threaded rods
• An approved silicone firestop sealant
Storage:
The FireMaster FastWrap+ and an approved silicone firestop
sealant must be stored in a dry warehouse environment on pallets.
Pallets should not be stacked.
Preparatory Work:
FireMaster FastWrap+ is installed with common tools, such as
knives, banders and capacitor discharge guns for applying insula-
tion pins. In order to install the duct fire stop system, the surfaces
of all openings and penetrating items need to be clean, dry, frost
free, and free of dust.
Installation techniques for Thermal Ceramics FireMaster
FastWrap+ (Figures 1 and 3):
• 3" (75 mm) Overlap Wrap Telescope - Each blanket overlaps
one adjacent blanket, and each blanket has one edge exposed
and one edge covered by the next blanket as shown in Figures 1
and 3. The visible edges of the longitudinal overlaps all point in
the same direction.
• Overlap Checkerboard Pattern - Blankets with both edges
exposed alternate with blankets with covered edges, as shown in
Figures 1 and 3. The visible edges of the longitudinal overlaps
alternate their directions and appear on every other blanket.
• Butt Joint & Collar System - Adjacent blankets are butted tight-
ly together and a 6" (152 mm) wide collar of FireMaster
FastWrap+ is centered over the joint, overlapping each blanket by
3" (75 mm) as shown in Figures 1 and 3.
• 2 & 3 Sided Enclosure System - When space does not allow for
full wrap enclosure on all four sides of the duct, the FireMaster
FastWrap+ may be installed on 2 or 3 sides of the duct and
mechanically attached to a concrete or CMU assembly on the
unexposed side of the duct.
General:
To minimize waste, FireMaster material should be rolled out tautly
before measuring. Cut edges of the blanket shall be taped with alu-
minum foil tape to prevent exposed edges of the insulation from
wicking moisture from condensation or grease from a compromised
leaking duct joint into the material and causing degradation of the
fire barrier. The FireMaster FastWrap+ material may be installed
with either a mechanical banding system or insulation pins and clips
(see Mechanical Attachment Methods below and Figures 1 and 3).
When using the banding technique, caution shall be taken to ensure
that the bands are not fitted too snug as which could result in cut-
ting into the blanket. To prevent blanket sag on ducts with dimen-
sions greater than or equal to 24" (600 mm), insulation pins, long
enough to extend through the layers of blanket insulation, are weld-
ed to the duct in columns spaced 12" (305 mm) apart, between 6"
and 12" (152 and 305 mm) from each edge and 10 (267 mm) on
center along the bottom horizontal and outside vertical duct runs.
Insulation pins that extend beyond the blanket wrap shall be tuned
down to eliminate sharp points. Support hanger systems do not
need to be wrapped provided that the steel hanger rods are at least
a minimum of 3 /8" (9.5 mm) diameter and the steel angle is a mini-
mum of 11/" x 1 x /e" (38 mm x 38 mm x 3.2 mm), or SMACNA
equivalent support system (SMACNA band strap support systems
do not apply). Horizontal trapeze support systems may be incorpo-
rated into the wrap enclosure.
A. Overlap Wrap Telescope Installation
FireMaster FastWrap+ commercial kitchen grease or air ventilation
duct 1 or 2 hour enclosure includes a one -layer wrap construction
applied directly to all surfaces of the duct (Figures 1 and 3). The
FireMaster FastWrap+ blanket is wrapped one layer 1'/2" (38.1 mm)
or 2" (50 mm) thick around the perimeter of the duct with a length
cut to provide enough excess to overlap itself not less than 3" (75
mm). Adjacent blankets are placed to overlap the previous blanket
not less than 3" (75 mm). The overlap made by adjacent blankets
forms the "longitudinal" overlap. The overlap a blanket makes with
itself is called the "perimeter" overlap. The wrap layer may be held
temporarily in place with filament tape 11/2" (38 mm) from each blan-
ket edge and in the center of the blanket until the mechanical band-
ing or pinning and clip attachment method is secured.
B. Checkerboard Wrap Installation
FireMaster FastWrap+ is cut to completely wrap around the perime-
ter of the duct with enough excess to provide an overlap of not less
than 3" (75 mm) (Figures 1 and 3). The blankets with both edges
exposed alternate with blankets with covered edges as shown in
Figures 1 and 3. The visible edges of the longitudinal overlaps alter-
nate their directions and appear on every other blanket. A 3" (75
mm) longitudinal overlap is installed onto the previous adjacent
wrap forming a "checkerboard" construction. The wrap layer may
be held temporarily in place with filament tape 11/" (38 mm) from
each blanket edge and in the center of the blanket until the mechan-
ical banding or pinning and clip attachment method is secured.
•
C. Butt Joint / Collar Installation
FireMaster FastWrap+ is installed in a single layer directly to the
duct with a tight butt joint construction (Figures 1 and 3). The
FireMaster FastWrap+ material may be held in place with fila-
ment glass tape 1 (38 mm) from each blanket edge and In the
center of the blanket temporarily until the mechanical banding or
pinning and clip attachment method is secured. A 6" (152 mm)
wide FireMaster FastWrap+ Collar is centered over the joints
overlapping on each side of the blanket joint 3" (75 mm).
D. 2 & 3 Sided Wrap System
When space does not allow for a complete wrap applied to the
duct on all four sides, the FireMaster FastWrap+ can be installed
in a single layer on the 2 or 3 sides of the unexposed duct and
mechanically attached to a concrete or CMU assembly. The
FireMaster FastWrap+ is installed on the duct as described in
one of the three installation methods described above with the
starting edge of the blanket attached to the concrete or CMU
assembly and then wrapped around the duct until the other end
can be affixed to the other concrete or CMU assembly, thus
encapsulating the duct with insulation around all accessible
sides. The blanket is to flange out onto the concrete or CMU
assembly. It should be secured to the adjoining assembly with
minimum 3 /16" (4.7 mm) diameter, 4" (100 mm) long concrete
anchors, footed to a minimum 1 (38 mm) wide x 3 1,6 " (4.7 mm)
thick steel strip /strap with pre - drilled holes spaced a maximum
10" (254 mm) on center. The FireMaster FastWrap+ insulation
wrap is secured to the duct with banding (see Mechanical
Attachment Methods for Insulation Wrap section below or
Figures 1 and 3). The ends of the banding are to loop into the
steel strips /straps that foot the blanket to the concrete floor or
wall, and are tightened down. The trapeze support system may
be incorporated within the wrap system.
Mechanical Attachment Methods for Insulation Wrap
1. Banding - 1 /2" (12.7 mm) wide carbon steel or stainless steel
banding, 0.015" (0.376 mm) thick, is placed around the entire
perimeter of the insulated duct with maximum 101/2" (267 mm)
spacing centers and 11/2" (38 mm) from each blanket edge or 1"
(25 mm) from each collar edge when using the butt joint and col-
lar method. When banding, filament tape can be used to tem-
porarily hold the blanket in place until the banding is applied.
The banding is placed around the material and tightened so as
to firmly hold the FireMaster FastWrap+ in place against the
duct, but not cause any cutting or damage to the blanket.
2. Pinning - Min. 12 gage, 5" long (125 mm) steel insulation pins
are welded to the duct at all blanket overlap locations (see
Figures 1 and 3) spaced in rows max. 10' /2" (267 mm) on center
and maximum 8" (200 mm) apart. An insulation pin is located
in the middle of the perimeter overlap and center spaced
between the pins. Pins are locked into place with 11/2" (38 mm)
diameter square or round, galvanized steel, speed clips or cup
head pins. Pins that extend beyond outer blanket wrap layer
shall be turned down to eliminate sharp edges or the excess
length cut off.
NOTE: Pinning is required for ducts larger than 24" x 48 ".
Through - Penetration Firestop System
When the duct penetrates a concrete or drywall fire rated wall,
ceiling, or floor, an approved fire stop system must be employed.
(Figures 2 and 4). FireMaster FastWrap+ approved through
penetration fire stop systems are listed in Section 4,
Specifications.
To fire stop the through penetration void area, cut strips of
FireMaster FastWrap+ 41/2" (106 mm) wide and as long as the
opening and install at a minimum 50% compression. Install the
strips so that they are recessed 1 %" (6.35 mm) from the top sur-
face of the wall or floor. Install a minimum W' (6.35 mm) depth
of an approved silicone firestop sealant into the opening to the
recess around the top surface of the floor or wall through -
penetration opening.
Grease Duct Access Door Installation
Four galvanized steel threaded rods, 1 /4" diameter (6.35 mm) by
41/2" to 5" long (114 to 125 mm) are welded to the duct at the cor-
ners of the door opening. Four 5" (125 mm) long 12 gage insu-
lation pins are welded to the door panel for installation of the
blanket. Two layers of FireMaster FastWrap+ are installed on the
door. The first layer is cut and placed on the pins and over the
access opening with a W' (13 mm) overlap. When the door is
installed, this first layer is compresses and fitted against the
wrap surrounding the door opening to form a tight butt joint. The
second layer is centered over the first piece so that a minimum
1" (25 mm) overlap exists around the perimeter. It is essential
that this layer fit tightly against the wrap surrounding the access
door opening with no through openings. The second layer is
impaled over the pins and both layers are locked in place with
speed clips. Pins that extend beyond the outer layer of
FireMaster FastWrap+ shall be turned down to avoid sharp
points on the door.
The insulated door panel and the steel tubes are placed over the
threaded rods and held in place with washers and wing nuts.
The steel tubes hold the door to the duct and protect the wrap
from damage as the door is removed. Alternatively, insulated
pre- fabricated access doors are available from FireMaster deal-
ers. See the Thermal Ceramics FireMaster FastWrap+ Design
and Installation Manual for complete installation and drawing
details.
7. Maintenance
No maintenance is required when installed in accordance with
Thermal Ceramics installation instructions. Once installed, if any
section that is greater that 8" x 8" is damaged or if the overlap
area is damaged, the following procedures will apply:
• The damaged section should be removed by cutting the steel
banding or removing the clips holding it in place
• A new section of the same dimension should be cut from a
roll of FireMaster FastWrap +, either 24" (610 mm) or 48"
(1220 mm) wide. Cut edges of the blanket shall be taped to
prevent exposed edges of the insulation from wicking
moisture or grease into the material and degradation of the
fire barrier
• The new section should be placed per Thermal Ceramics
manufacturer's Installation Instructions ensuring the same
overlap that existed previously
• The steel banding should be placed around the material and
tensioned so as to sufficiently hold the FireMaster
FastWrap+ in place without cutting the blanket
• If the blanket has not been damaged but the foil has ripped,
seal the opening with aluminum foil tape
For damaged areas less than or equal to 8" X 8" the following
procedure may be used.
• The damaged section should be removed by cutting out a
square or rectangular that includes the damaged area and
does not exceed 8" in width or length.
• A repair section should be cut from a section of FireMaster
FastWrap+ that is 1" wider and 1" longer than the damaged
area that has been removed. Cut edges of the blanket shall
be taped to prevent the exposed edges of the insulation from
wicking moisture or grease into the material.
• A single min. 12 Gauge insulation pin min. 3" long should be
welded to the grease duct in the center of the repair area.
(Note: Cup head pins may also be used.)
OPL Design No. GD 544 F and GD 562 F Figure 1
UL Design No. G -14 and V-19 Drawing No. FMFW1.5001 -1
1
One layer FireMaster FastWrap+ 11/2' thick
2
Steel banding 1/2" wide minimum
3
4
5
6
3" minimum longitudinal overlap
3" minimum perimeter overlap
6" wide FastWrap+ collar (for Butt Joint option)
Firmly butted joint (for Butt Joint option)
7
10 or 12 gauge steel insulation pin with 1'h" x 1'/2" or 11/2"
diameter galvanized speed clips (for alternate pinning)
•The repair section is to be centered on the opening and
Impaled upon the insulation pins. All overlaps should be
tucked Into the repair opening to provide a tight fitting joint.
Insulation Is held in place with a 1'/2" square or round galva-
nized or stainless steel speed clip or a minimum 1" diameter
cup head pin. The excess portion of the pin shall be cut off
and /or turned down to eliminate sharp edges.
•The Joint should be sealed using aluminum foil tape.
8. Limitations
• FireMaster FastWrap+ shall be installed in accordance with
Thermal Ceramics - Installation Instructions
• Multiple steel ducts In a single FireMaster FastWrap+ enclo-
sure system are not permitted for commercial kitchen grease
ducts. Multiple steel ducts in a single enclosure are permitted
for air ventilation ducts
• Grease Duct Sizes > 24 "x48" (600 mm x 1200 mm) insula-
tion is attached using steel pins
• Air Ducts: when maximum duct size dimensions are greater
than 84" x 21" (2100 mm x 525 mm) in cross section, rein-
force the duct with steel angles sufficient to support the total
weight of the duct assembly and the FireMaster FastWrap+
enclosure
Thermal Ceramics
F/
R
Fire Protection Systems
New and Improved FireMaster 11/2"
FastWrap+ Commercial Kitchen Grease
or Air Ventilation Duct
1 or 2 Hour Shaft Alternative
Zero Clearance to Combustibles
ote: The Integrity of FireMaster Duct Systems is limited to
the quality of the installation.
• Minimum 3 /8" (9 mm) diameter all thread steel rods do not
have to be insulated
• Horizontal support members may be incorporated into the
enclosure wrap
• The integrity of FireMaster FastWrap+ system is limited to
the quality of the installation
'For personal protective equipment recommendations see the MSDS.
Thermal Ceramics is a trademark of Morgan Crucible Company plc, FireMaster and
Fast Wrap are trademarks of Thermal Ceramics Inc. Fast Wrap products are manufactured by
Thermal Ceramics Inc. FireMaster Duct Systems are distributed by authorized distributors
and no longer by 3M.
Romeo and Fyre -SiI are tradenames of Tremco Inc.
Penal/ Is a tradename of Specified Technologies Inc.
835+ is a tradename of Rectorseal.
FS One is a tradename of HILT! Inc.
Special Note:
The original FireMaster FastWrap+ 2" technical
data and installation sheet is still available elec-
tronically at www.thermalceramics.com In the data
sheets section.
11/2
ss
Alternate
Pinning Technique
Grease Ducts Only:
Sizes >_ 24 "x48"
In Cross Section
Pinning Technique
Required.
11/2
Butt Joint Option
Cross Section View
Overlap Wrap Option
Cross Section View
Checkerboard Wrap Option
Cross Section View
11/2
•
Installation Pin Layout Figure 4
Drawing No. FMFW1.5004
1
Vertical section
2
Access door
3
10 or 12 gauge steel insulation pin
6 a.
CO
1
Thermal Ceramics
Faverpre A
Flre Protection Systems
1 "
(TYPI
Marketing Communication. Offices
Thermal Ceramics Americas
T: (706) 796 4200
F: (706) 796 4398
Thermal Ceramics Asia Pacific
T:465 6733 6068
F: +65 6733 3498
Thermal Ceramics Europe
T:+44 (0) 151 334 4030
F: +44 (0) 151 334 1684
04.05/7 14230/5M
New and Improved FireMaster 11/2" FastWrap+ Commercial Kitchen Grease Duct
Typical Insulation Pin Layout for Duct Spans > 24" Wide to Prevent Blanket Sag
111111
SIDE ELEVATION
VARIES
BOTTOM VIEW
Note: The Integrity of FireMaster Duct Systems is limited to
the quality of the installation.
• „,;•: •••• •
I
North America - Sales Offices
Canada
T: +1 (905) 335 3414
F: +1 (905) 335 5145
Mexico
T: +52 (555) 576 6622
F: +52 (555) 576 3060
United States of America
Eastern T: (800) 338 9284 F: (706) 796 4324
Western T; (866) 785 2738 F: (866) 785 2760
12"
U)
UI
ce
South America - Sales Offices
Argentine
T: +54 (11) 4373 4439
F: +54 (11) 4372 3331
Brazil
T: +55 (21) 2418 1368
F: +55 (21) 2418 1205
Chile
T: +56 (2) 854 1064
F: +56 (2) 854 1952
END ELEVATION
Colombia
T: +57 (2) 2282935/2282803/2282799
F: +57 (2) 2282935/2282803/23722085
Guatemala
T: +50 (2) 4733 295/6
F: +50 (2) 4730 601
Venezuela
T: +58 (241) 878 3164
F: +58 (241) 878 6712
•
Catalog
Humber
Mar. HP/
lieu. WI.
i .
Fan
RPM
Tlp
Speer
013P
1/8 9P
114 SP
3/8 SP
1/2 9P
5/5 OP
3/4 SP
718 SP
1 SP
1.1/4 SP
1.112 SP
:IHP
B HP
HP
MT
Sone[BHns P
So BHP
Sorel BHP
Sone1 BHP
Sonel IMP
Sonsl SHP
ns
Sons] BHP
Sone/ SHP
1501328
Ire
15 tbs.
2358
12138
4.2. I . 4
1
I
I
T
I
1
I
I
1
840
2515
10 6
11 2
844
414
4.5 .05
. .05
- �
- � -
000
2672
1
1249
0 0
6.8 .05
5.51.06
4.9 1.06
720
2630
1521
1344
1 40
_J,___
' .06
8,4 I .07
1438
6.6 1 me
1253
J
688
1
I
I
I
I
I
760
7057
1606
7.5 • .08
7.1 I .09
6.4 1 .09
5.9 1 .09
I
1
I
1
1
1
800
3144
1680
1531
1060
1115
.09---Ti
.10
7,2 1 ,11
0,8 I .11
I
J
1
1
I
I
I
840
39
1775
1624
1485
1269
a,9 .11
8.6 .12
8.0 1 .12
7.3 1 .13
t
I
1
I
I
J
580
3468
1 19
171
1580
1391
1 ode
6.8 f .12
9.3 I .13
9.0 J .14
6.1 1 .14
7.6 1 .14
I
I
J
I
1
I
935
30 75
1970 18x0
1702
1548
1337
T .9 .15
10.4 I .16
10.1 [ .17
9.6 I .17
5.7 1 .16
1
I
�
I
1501:139
1/4
15 lbs
Stirs
38 71
201!1
1 53
1822
1680
1513
1 73
12.0 .17
11.71 .19
2085
11.1 20
10.4 .20
18
10.1 l 21
1i�`i
9.1 I .19
1449
I
I
1
I
1035
4088
2197
um 1 .20
12.72 .21
12. .23
11.71 .23
11.11 24
10.71 .
I
1
1
1
1080
4244
2292
2105
2046
1924
1786
162.3
1292
14.31 .23
19.71 ,24
2232
13.41 .26
2 16
12.71 .27
1998
12.41 .27
1887
11.71 .27
1719
10.91 .25
1470
1
I
I
1
r
150R413
1/3
19 lbs.
1110
4302
2345
14.6 .
14.
.27
1 as .
1 . 2 .29
12.5 .29
11.9 .30
1140
4480
2459
I.
:.:
1 15
5.3 7117
1fS 26
2 7
14W .30
2287
T4.21 .31
2158
13.7j .32
2038
f3.21 A2
1907
12.8J .32
1750
I
1449
I
I
1
117]5
4819
2433
1 .30
15,9t .31
15,31 53
15.11 .94
14.81 .35
13.91 .35
13.61 .35
12.91 .33
J
I
15013513
1/2
23I0a.
1295
]296
46
5089
1 - �.'s
26 10 2607
2404
23 00
2
2071
1940
1760
T4
- r
17Y1.34 17.1l .36
15.91 .36
16:61 40
T5.9 40
15.71 .40
15.31 .41
14.81 .41
1491 .38
2730
. 0
2639
2541
2441
2340
22.30
2111
1979
1766
18.61 .40
2t70
7i.21 .42
2576
18.11 .48
81
17.71 .46
2405
17.01 .40
238 5
18.7 47
2275
16.21 .47
2156
17.51 .54
2339
15.91 .48 L
2016
17.1 .54� f
22 1825
I
te
_r
1 7
21 1 .78
1386
5325
2653
0 -
20 .48
2912
19.81 49
2
19.21 .50
2732
19.0
2641•
- 18.7153
2548
18.8 53
2 7
i50148g
3/4
Si lbs.
1420
1485
5551
5836
10
zz7 .53
3t � e
.60
21 l 53
3063
24J .61
3183
21 1 .57
2957
23 1 .62
3101
25 1 .70
21 1 .58
2881
23 1 .07
9016
241 .72
I-6
20 o
2795
22 1 .65
2935
24 1 .14
21n.61
22J .7r
2851
1 j .77
19.91 .61
2814
21 .70
2755
24 1 .79
19.5l 62
251
21 1 .70
2672
23 I .79
.1
9 2140
21 20 72
25 35
22 I .79 22 I .81
1545
60 72
3215
1 .68 25 1 .19
150 ACRU -B Data
U` Data
Wheel Diameter • 15"
Tip Speed (FPM) - 3.9 x RPM
Maximum RPM -1545
Maximum IOI1P - .22 x (RPM /1000)
Maximum Motor Frame - 56
ShippIng Weight (Lou Motor) - 70 lbs.
Curb - RCO. RCA - 22
Roof Opening -1 9 -1/2" Sq.
Material Daugpe
Top Clap - .064
Baffle - .084
&tae - .064
Psrfu rmxto• shown la for netatlotlon type A: free Inlet, tree outlet, power rating (13H P) does not Include drive lasses. Performance ratings do not Include the effects of agoutis-
Minoan In ate airstream. The sound ratings shown are loudness vuluos In fun sonee at 5 ft, (1.5m) In a hem spherical tree field calculated par AMCA Standard s01. Values
shown ors for Installation typo N. free Inlet fen sone levels,
Otl -d Z00 /Z00'd 08P -1
L sip
Permit No.
0901- S91 -90Z
RECEIVED
CITY OF TUKWILA
DEC 19 2005
•
PERMIT CENTER
140
1,20
1,00
LL
F 0,150
g moo
0,40
0.29
0
A
I" I 1,:.f1ff 1711MM
111111011EMAIMII
M
0
REVIEWED FOR
CODE COMPLIANCE
arionnewcn
JAN 1 1 2006
Too
1400 2100 1900 3500
FLOW (CPhQ
I 1 I
011 I v -Woad wd90:10 90 -51 -330
46
UPsoripUon • fan shall bar a spun aluminum, roof mounted, belt driven, upblast centrifugal
exhaust ventilator.
Certifications - Fan shall be listed by Underwriters Laboratories (UL 705) and UL listed for
Canada ( 705). Fart shall bear the AMCA certified ratings seal for sound and air per-
formance.
Construction - The fan shall be of bolted and welded construction utilizing oorroslon resis-
tant fasteners. The spun aluminum struoturrl components shall be constructed of minl-
mum 16 gauge marine alloy aluminum, bolted to a rigid aluminum support structure.
The aluminum base shall have a one place Inlet spinning and continuously welded curb
cap corners for maxirrum leak protection. The windbend shall have a roiled bead for
added strength. A two niece top cap shall have quick release latches to provide access
Into the motor compartment. An integral conduit chase shall be provided into the motor
compartment to facilitate wiring connections.
The motor, bearings and drives shalt be mounted on a minimum 14 gauge steel power
assembly, isolated from the Unit structure with rubber vibration Isolators. These compo-
nents shall be enclosed In a weather -tight compartment, separated from the exhaust
airstream.
Unit shall bear an engraved aluminum nameplate and shall be shipped in ISTA certified
transit tested packaging,
Wheel - Wheal shall be centrifugal backward Inclined, constructed of 100 percent alumi-
num, Including a precision machined cast aluminum hub. Wheel Inlet shall overlap an
aerodynamic aluminum Inlet cone to provide maximum performance and efficiency.
Wheel shall be balanced in accordance with AMCA standard 20496, balance quality
and vibration levels for mans.
Motor - Motor shall be heavy duty type with permanently lubricated sealed ball bearings
and furnished at the specified voltage, phase and enclosure.
Bearings - Bearings shalt bu designed and individually tested specifically for use In air han-
dling applications. Construction shall be heavy duty regreasable ball type In a cast iron
housing selected for a minimum L50 life in excess of 200,000 hours at maximum cata-
loged operating speed.
Belts and Drives - Belts shall be oil and heat resistant, non - static type. Drives shall be pre -
claion machined cast iron type, keyed and securely attached to the wheel and motor
shafts. Drives shall be alined for 150 percent of the installed motor horsepower. The vari-
able pitch motor drive must be factory set to the specified fan IPM.
Product - Fart shall be model ACRU -B as manufactured by Loren Cook Company of
Springfield, Missouri.
ACRU.B Dimension Data
Mae
MUZi � L �
19 ILSE Mil
1113121521111112=111
11131111LIMBILLUIR
SEA r-
L
0-1 = !M
L i i 1 YL
trSILL
La, J
100
A
B
30.1 4
•
•
T
•
IL,; • e-9 o
ra I • Lis
20
11111ft11111111E2M111111111111M : f
It.11iiiii3;!
iiiLIII p 111111E1M1111111U
EMI
11111E911111111EWall11111111111111Mr41111111M -
11111112 1111111011221111111111
as
30
54
5-1 2
25 -112
49 -1
30
100
50'
5
CS-
24
35-
-1
C T Sq.
Hoot Sr Opening
16
1
4
37.1 2
-916
Approx. Shipp.
t: Lbs Lards Motor
4 "
r• 110111101 - .
5 1 . iiiiit.111illc7 '
1
041 -d 2001100'd 081-1 Og81- 692-902
2
All dimensions In Inches. 'Root opening Ws for cults auppikfd by Loren 00ok Corrraany only.
Specifications and Dimension Data ACRU-B
650
Upblast Centrifugal
Exhaust Ventilator
Moot Mounted
Belt Drive
�+-- -- T Se. ---- 1 t
Loren Cook company certifies that
the ACRU -fl shown herein are
licensed to pegs the AMCA Seel.The
ratings Shown are based on ball
end procedures performed In
accordance with AMCA Pub1Cation
211 end AMCA Publioation 311 and
comply with the requirements of the
AMCA Certtlred Ratings Program.
Type ACHU -B Is furnished
standard with UL 705 and
11$ cUL 705 Itatlnqs (Power
VentUator/ when rurniaAed
with rectory supplied motor. •
DslJiV -IMOd tid40t10 gO-81 -030
09 -05 -2006
ROBERT MCNEELY
230 COUNTY LINE RD SW
PACIFIC WA 98027
RE: Permit No. M05 -199
3455 S 148 ST TUKW
Dear. Permit Holder:
In reviewing our current records the above noted permit has not received a final inspection by the City of Tukwila Building Division.
Per the International Building Code and/or the International Mechanical Code, every permit issued by the Building Division under the .
provisions of this code shall expire by limitation and become null and void if the building or work authorized bylsuch permit is not : .
commenced within 180 days from the date of such permit, or if the building or work authorized by such permit is suspended or .
abandoned at any time after the work is commenced for a period of 180 days.
Based on the above, you are hereby advised to:
Call the City of Tukwila Inspection Request Line at 206 - 431 -2451 to schedule for the next or final inspection.
This inspection is intended to determine if substantial work has been accomplished since issuance of thc,permit or last inspection; or if
the project should be considered abandoned.
If such determination is made, the Building Code does allow the Building Official to approve one or more extensions of time for
additional periods not exceeding 90 days each. Extension requests must be in writini and provide satisfactory reasons why
circumstances beyond the applicants control have prevented action from being taken.
In the event you do not call for the above inspection and receive an extension prior to 10/23/2006, your permit will become null and
void and any further work on the project will require a new permit and associated fees.
Thank you for your cooperation in this matter.
Sincerely,
xc:
arshall,
ermit Technician
A5Lai
Permit File No. M05 -199
City of Tukwila
Steven M. Mullet, Mayor
Department of Community Development Steve Lancaster, Director
6300 Southcenter Boulevard, Suite #100 • Tukwila, Washington 98188 • Phone: 206 - 431 -3670 • Fax: 206 -431 -3665
ACTIVITY NUMBER: M05 -199 DATE: 12 -19 -05
PROJECT NAME: CHURCH BY THE SIDE OF THE ROAD
SITE ADDRESS: 3455 S 148 ST
X Original Plan Submittal Response to Incomplete Letter #
Response to Correction Letter #
Revision # After Permit Issued
DEPARTMENTS:
Bui . i Division
Complete
Comments:
Public Works n Structural ❑ Permit Coordinator
DETERMINATI N OF COMPLETENESS: (Tues., Thurs.)
Permit Center Use Only
INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED:
Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
TUES/THURS ROU ING:
Please Route Structural Review Required
REVIEWER'S INITIALS:
APPROVALS OR CORRECTIONS:
Approved ❑
Notation:
REVIEWER'S INITIALS:
Documents/routing slip.doc
2 -213 -02
?EMT COORD COPY
PLAN REVIEW /ROUTING SLIP
6(,1 Avg
Fire 11 ,t revention
Incomplete Ti
Planning Division
DUE DATE: 12-20-05
Not Applicable Ti
No further Review Required
DATE:
DATE:
DUE DATE: 01-17-06
Approved with Conditions Not Approved (attach comments) ❑
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
License Information
License
SKILFSMI69RE
Licensee Name
SKILFAB SHEET METAL CO
Licensee Type
CONSTRUCTION CONTRACTOR
UM
600555086
Ind. Ins. Account Id
48013000
Business Type
CORPORATION
Address 1
230 COUNTY LINE RD SW
Address 2
City
PACIFIC
County
KING
State
WA
Zip
98047
Phone
2533330014
Status
ACTIVE
Specialty I
SHEET METAL
Specialty 2
WELDING
Effective Date
12/5/1984
Expiration Date
12/13/2006
Suspend Date
Separation Date
Parent Company
Previous License
Next License
Associated License
Business Owner Information
Name
Role
Effective Date
Expiration Date
MCNEELY, ROBERT S
01/01/1980
MCNEELY, DANIEL R
01/01/1980
MCNEELY, MARIANNE
01/01/1980
NEFF, SUSAN M
01/01/1980
STEWART, BRUCE
01/01/1980
01/01/1980
MCNEELY, DANIEL S
01/01/1980
01/01/1980
Look Up a Contractor, Electric '-‘n or Plumber License Detail
Washington State Department of Labor and Industries
General /Specialty Contractor
A business registered as a construction contractor with L &I to perform
construction work within the scope of its specialty. A General or Specialty
construction Contractor must maintain a surety bond or assignment of
account and carry general liability insurance.
Bond Information
Bond I Bond I
https: / /fortress.wa,gov /lni/bbip /printer.aspx ?License= SKILFSM 169RE
Page 1 of 3
01/19/2006
•
•
-mom. ••••• ••• 115. •
fib
•••■••
U.B.G. CODE INTERPRETATIONS:
On.e-hour rated fire resistance for steel columns and all members or primar tr..:sses p C. '5111PP:102
1-1.1
•
"Multiple layers of I/2" (12.1 mm)evpson wallboard adhesively sec to column flanges a'd successive 1.:•
Wallboard applied without horizontal jo'ints. Corner edges or each !aye staggered. Walbord Lays. below outer layer
secured to column with doubled 0.049 inch (124 mm) (No. 18 13.W. 6362e) steel wire ties spaced 15' (35: or) on
center. Exposed corners taped and treated.'
One-hour rated fire resistance for exterior/interior wall assemblies per U13.C. 'Si Table 1-5 item n-13 .,_
'2' b 4 (51 mm by 102 mm) wood studs 24' (610 mm) on center with 5/8' (15.9 re). Tpe X e purn ki,alboa
applied vertically or horizontal's n3iled with 6•cl cooler or wallboard nails at 1" '118 re) on center 'Lib e joints on
nailing members. Stagger Joints each side.'
Cte-hour rated fire resistance for cellin,a/floor assemblies per U.B.C. "91 Table 1 - C Item 2141
'Base layer 5/8' (15.9 mm) Type X ey p sum wallboard applied at right angles to Joist or truss 24"
(6)0 mm) on center with 1-1/4" (32mm). Type S or Type W drywall screws 24' (b10 mm) on c.anter. Face
layer 5/8" (15.5 mm) Type X ey psum wallboard or veneer base applied at right angler to Jost or
truss through base layer with 1-1/8" (48 mm) Type S or Type W drywall screw 12" (305 mm) on center at
Joints and intermediate Joist or truss. Face layer joints offset 24" (610 mm) From base laser.lointe,
1-1/2" (38 mm). Type G drywall screws placed 2" (51 mm) back on either side of face layer end joints,
12" (305 mm) on center!'
Ct)e-hour fire resistance for floor or roof conitruction assert i'oHe5 &bI1.CJt miote this is in
conjunction with Table 1-C Item 21-1.1 listed above)
" Wood Joist, floor trusses and roar trusses spaced 24' (610 mm) o.c. with V2' (12.1 mm) wood structaal panels
with exterior glue applied at right ang;es to top of Joist or truss with ed nails. The wood structural pane thickness
shall not be less than 1/2" (12.1 mm) nor less than required by Chapter 23."
One-hour fire resistance (walls and ceilinos) membrane and through penetrations repuirer, ts er
U.B.0 4 3 - 1 Sections 10912 4 1102.
All membrane and through wall/ceilino, penetrations shall be protected by an approved
pe n
firestop system installed as tested in accordance with Uf3C Standard 1-5. Tile system
F rating of not less than the required rating of the wail penetrated ancilor a T rating of not 55
than one-hour but not less thar the required rating or the floor penetrated.
TABLE 15-5-1 ASPHALT SI-INGLE APPi 1CATiON
Asphalt strip shingles mas be installed on siopes as low as 2 units vertical in 12 units hbrizorfAi f16.1
% slope), provided the shingles are approved self-sealing or are hand sealed and are instiiI:ed
with an underlayfnent consisting of two layers of nonperforated Type 15 felt applied shingle • hion.
Starting with an 18-inch-wide (451 inn) e.het and a 36-inch-wide (514 mm)sPeet over it at the eaves,
each subsequent sheet shall be lapped le inches (483 mm) horizontally.
SECTION 1508 - VALLEY FLA51-1ING
1508J Valleys. !Zoo!' valley flashinds shall be as noted in this section. Shingle application 1,1;z11 be
con.sistant with applicable Table 15-5-1, 15-5-2, 15-D1 or 15-0-2.
15082 Asphalt Shingles. The roof valley Flashing shall not be provided of less than 0.0*-Irch (0.41
min) (No. 28 e alvan;zed sheet page) corrosion-resistant metal, and shall extend at least 8 ind
(203 mrr) from the center line ea& u.:ay. Sections of fiashings shall have an end lap or not lees than
4 inches (102 mm). Alternately, the voiles shall consist of woven asphalt shir•gles ap14.d in
accordance with the manufacturer's printed instructions.
In each ozse, the roof Valles fiashine, shall have a 3.S-inch-wide (V4 cm) uncierlagnent • In
Tab e 15-B-I. In seve-e clirnates t' metal valley f:ashino LAderlayfr.ert shall be bond co to
the roof vide-, :ayrr.efit for slop unclear 1 units vertical in 12 un",te horizontal (583% 6lope).
f;0612, 604e
D4. gx 6 5.CA:cod door vi lures haridie",
D-2 Plc 1 6L- Wood door VI5a-cice-itrieverkirdiel,
D-3 3 x lag 5.C. 4c01 clan' vill4eg-cts5Ge lox kW C.?b -
D- 3° bs Door WeAiller9t bottam 4-e' 0-5 3• . 14. F‘ive bu.+45 OW) 14W.
p bcur tux w ca.)
aow. ex.* w4%1A-5-brie dopy bo-i
A% .
•16
4'
DEMOLITION NOTES:
1. Coordinate u.,11h new Moor and roof plans for dim and locations.
2. Coordinate with Owner for Items to be salvaged and/or be re-used.
3. Coordinate with supplementary demolition plan(s) as provided in these construction documents. -
4. Contractor to verify location of all utilities and piping before beginning work. Protect or move utilities
as required.
5. Remove all existing plumbing, r eisinarlfcal and electrical work not to be reused in It's present
locations. Cap all abandoned utilities as required. All mechanical/electrical Items in these
construction documents are for reference only and are not Intended to describe the work fully.
Provide all work necessary to remove, patch and finish existing work to accomplish completed spaces as indicated on the drawings and specifications.
1. Patch and repair all areas Involving demolition work to match adjacent existing conditions or to
accept new construction (see new plan).
8. During demolition of the exterior, contractor to set aside material that can be reused in areas ewe
patching existing walls is required.
9. Dash lines indicate existing conditions to be removed unless noted otherwise.
10. Saw cut Floor, Wall and Roof areas to receive new footings, windows, doors and rellte items. Frov
a straight edge to receive new work For dimensions see new floor plan.
• 11. Provide temporary wood shoring as required to place new structure.
12. Provide dust proof closures.
13. Protect adjacent areas in building from damage. Repair all damages.
14. Coordinate all work with the ()timer, who will be occupying the building chring construction. Protect:
the Owner's equipment and 11rnishings.
15 . Report immediately to the Architect any discrepancies and conditions which may differ from the
drawings or specifications
16. Contractor will be responsible for all removal or debris from site.
SPECIAL INSPECTION REQUIREMENTS:
1. Special Inspections shall comply with 1951 Uniform Building Code Section 1101.
2. All inspections reports must be submitted and approved b the building official prior to
issuance of a certificate of occupancy.
3. Concrete. During the taking or test specimens and placing or reinforced concrete. Rc view
reinrorcing steel placement according to construction documents.
ABBREVIATIONS S
A.13.
13.5.
CL. or C
CONT.
CPT.
Ct
D.
P.O.
P.S.
EX.
ExP. BO_T
F.E.
F.\
G1._ 4
GA.
GhLV.
44_
ANCHOR BOLT
.ABOVE FINISW FLOOR
6A0( 5°L.A5f4
BEAM CONTROL/CONSTRiCTiON JOINT
CENTFJZ_NE
C 14
CNT.j0U5
CARPET
CLA55ROal
DEPTH
DRINKNG FOUNTAIN
DEDiCATED CUTLET
DOLN SPOUT
EX15Th6
EXPAN5:0N BOLT
FLOOR CFRAIN
F:RE EXTIN6S5ER
FIN:5'r; FI.COR
FACE � F'LYLOOD
GLLE LAPINAT
ciAtrzE
GALVAN•zzo
PCX.L0t11 COREMANDICAP
POLLC41; I
-EAL
•
1-.
MIL
N.T.5.
O.C.
PLS.
PL•LLO.
PR.
PT.
R.I.
Sly
Sc.
5.v.
SWT. MTL.
sal
T G
T.00
T.0111
TRT.
TYP.
w.
kW.
LENGTH
METAL.
NOT TO SCALE
a CENTER
OPPOSITE I-1AND/OvER HANS
ORE.NTED STRAbO BOAR!)
PARA LAMINATED BEAM
PLASTC LAMNATED
PLYWOOD
PAIR
PANT
ROJC.44-IN
5TArN... I VAR
50-ID CORE
5:-EE T ¥Y1_
5;-EET tdETAL
5L'I'LAR
TaCT:2 4 GROOVE
TOP OF COsiCFTE
TO CF LALL
'141 •
TYPICAL.
UNLESS NOTED 011-ESE
UDE
WER F-FOOF
WOOD
I •
•
r
•
SYME3OL 5
„ZONING:
RC
i;Er-icx:.)EL 4 SLINIZI:›A'r SCHIQC)L Ar=)EDITICDN
PROJECT DATA
ADDRESS:
3455 SO. 148T1-1 TREET
SEATTLE, WA S36&
Slcic,3. 3tIon N..onl'oer
Sheet Number
Detail Nur-1
Sheet Nurnba-
Gricliine fiurd=>&. or letter
Shear Wall Tie
•
SCOPE OF WO(:
ADD 2,154 5F 0= SUNDAY SCHOOL AREA ON T14E SECOND
FLOOR (ABOVE THE EXISTING ADMINISTRATIVE AREA?.
REMODEL NE 7- LOBBY AREA LI4ICI-1 WOULD
INCLUDE THE 118 4I5ING" OF NE ROOF.
CODE:
1991 EDITION, UNIFORM BUILDING CODE WIN WASI-INGTON
AMENDMENTS
CLASSIFICATIONc:
EXISTING: A2.1, 4 El
PROPOSED: 5 El
c.21$1Lan
EXISTING: V-1 V1s1
PROPOSED: V-1 I4OUR
STORIES:
ONE 4 TUJO
SITE AREA:
3 ACRES
•GROSS 6UILD1 AREA: (SUP SF..)
EXISTING: 30,23E:-.- 5F.
PROPOSED: 2,19.-4 SF.
REMODEL: 1,51z- SF.
■•••••••••.,-
BEY/
chirrIlf shei be node
c_ • riOr Zr';'.-r-."'
;
.
Corp
1-IVAC Equip
Glazing %
Roof's
Wall
15%
R-21
ET)
1.
2.
3.
4.
5.
GENERAL KOTE5:
b.
a.
10.
II.
12.
Product specifications incorporated throughout Construction Documents.
Install materials/products Fs' manufacturer's recommendations and
specirica tiore.
All work shall be perrorrecl in strict accordance to the Architect's
construction otocuments.
Do not scale drawings
All work shall be performed in strict conformance with all governing building
codes and regulations.
The Contractor shall be responsible for all work that has been performed
which does no: meet these codes anti regulations.
The Contractor shall verify dimensions denoted on the construction documents
as 'field verify on site prior to commencement of construction.
The construction work shall be limited to the immediate area in which the work
is bein. performed.
The Contract cy shall be,reponslble for the cleaning of all the debris and
dust throughout the site which is a result of this construction project.
The Contractor shall be responsible for the removal and disposal of all
debris for the site. All costs for the removal of construction debris shall be
the sole responsibility of the Contractor.
The Contractor shall strive to maintain a clean and debris-free working site.
The Contractor shall be responsible for roof and finish details.
1'
40 A0 F loVER F S--IEET
A30 R •461-
• 4 FLOOR FRAMING PLANS 4 DETAILS
A2.0 FOND
PLAN 4 DETAILS
44.0 voILDING.: SE S DETAILS
A DETAILS
SEPARATE PER.Nar
REQUIRED FOR:
Mechanicai
If Electrical
0 Pkinbing
0 Gas Ptong
city Of Tukviii:a
BUILDING DIVLSION
ENERGY CODE COMPLIANCE:
(ZED tes Climate Zone I)
!BUILDING
Prescriptive
Requirets Proposed
Option III Meas;re
'Fertaee of glazing Is based upon the
gross exterior area.
EX TO RAUJING5
Gas Furnace
R-30
R-15
•
It
p
PROJECT DATA
OUNE R
CRC;-1 BY r 5 OF TkE ROAD
F.O. Box 68545
taeattle, WA salb8
206-243-5024
ARCHITECT
Afch7tects p s.
12202 Pacific Avenk;e, S,:te C
7 ocorla WashInetor, 92444
;53-531-
CONTACT: Jo'rri
STRUCTURAL ENC
David WC. l...;c.r.o
- e23o NE. I.74;e1 c..e
Kancl,
.425 -823-3330
CONTRAC.TOR
(-es 14ar.se:
i*G..encAtze: 206 - 2214412
pee
- cc/1
...Fa. • •■•••••••■••••
131,
taindinl
SO left WSW S-:-
aD awn and mamba.
real gif amietdio dicammemi don not alluils
Os Man ri amend
er woad Aid
diffeerkOme
Otv d %bib
111111111116 MOM •
r E.\)IEA ED
tk onorm isn
CODE.CO
AS 1 7..Z0
0.
1220
Taco
P: 253
E: or
Job P:
Dote: 20. Ve I PA
Revs:
NA
p.s.
cific Av Suite C
Woshi on 98444
.4300 • .537.6542
cts0 fincino.corn
4•111111111•1111=1.■
)4011 I 11
•
.r •
•
y.
• . .... 44
w •
f
•
•
•
•
•
•
• •
•
•
•
•
•
•
•
•
•
•
•
• .
N
•r
•
eWritA . PFYevoSe - ..
.
••
•
•
.4 -
•
•
•
S
1
• ♦ • ••
•
• • •
•
•
•
•
i
. •.
• •
•
•
•
• t
•
••
•
•
•
Existing Plans - Rom
SLALE : • =100'
9
•
CODE
t,r% /WI
T v vH•"
•
•
J
J
1 3
ci_
tist
w
1
Al. 0
M
- C
< -
s.+
00
0 :g
c \.?
�,
-or
Cn
(YL 'n
J
0
0
— — s.
a,
i
•
MO.
d
•
•
•
l
I-
1■IC 09_ I Commercial food heat-processing
appliances r qu :red b. Section to ha %e a
Type I hoed shall be provided with an approxed
automatic tire _suppression system complying with
the International Building Code and the
International Fire Code.
S.
r *
to
-
J
c:
r•
°t
? .
r
-r •
,5
•
L
ire -wrap insulation shall extend down through
shaft to room ceiling surface penetration.
OR
xtend shaft enclosure to meet code requirements
as described below:
2003 1MC
506.3.10 Grease duct enclosure. A grease duct
serving a Type I hood that penetrates a ceiling,
wall or floor shall be enclosed from the point of
penetration to the outlet terminal. A duct shall
penetrate exterior walls only at locations where
unprotected openings are permitted by the
International Building Code. Ducts shall be
enclosed in accordance with the International
Building Code requirements for shaft construction.
The duct enclosure shall be sealed around the duct
at the point of penetration and vented to the outside
of the building through the use of weather -
protected openings. Clearance from the duct to the
interior surface of enclosures of combustible
construction shall be not less than 18 inches.
Clearance from the duct to the interior surface of
enclosures of noncombustible construction shall be
not less than 6 inches. The duct enclosure shall
serve a single grease exhaust duct system and shall
not contain any other ducts, piping, wiring or
systems.
S
•
Mos gm
REVIO ED FOR
C0
Victn ^w trr
JAN , , n , ;
- --
Obi O c t r , v
C. 1