HomeMy WebLinkAboutPermit M02-068 - SHEARER GARYM02-068
Shearer
Residence
4433 s 156 St
DESCRIPTION OF WORK:
Install fireplace insert
City of Tukwila
Department of Community Development / 6300 Southcenter BL, Suite 100 / Tukwila, WA 98188 / (206) 431 -3670
Parcel No.: 8108600258
Address: 4433 S 156 ST TUKW
Suite No:
Tenant:
Name: GARY SHEARER
Address: 4433 S 156 STREET, TUKWILA, WA
MECHANICAL PERMIT
Owner:
Name: SHEARER GD Phone:
Address: 4433 S 156TH, SEATTLE WA
Permit Number: MO2 -068
Issue Date: 05/03/2002
Permit Expires On: 10/30/2002
Contact Person:
Name: CANDICE GALLAGHER Phone: 206 - 378 -6632
Address: 2800 THORN DYKE AVE W, SEATTLE WA
Contractor:
Name: WASHINGTON ENERGY SERVICES CO Phone: 206 282 -4700
Address: 2800 THORN DYKE AVE W, SEATTLE
Contractor License No: WASHIES990CW Expiration Date: 02/16/2003
Value of Construction: $0.00 Fees Collected: $51.75
Type of Fire Protection: Uniform Mechnical Code Edition:
Permit Center Authorized Signature:
kcbtrutr (i X�i ,C
Date: S 3 `
I hereby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and
ordinances governing this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws
regulating constru tion or the• -rfor a I- of w; rk. I am authorized to sign and obtain this mechanical permit.
Signatu
doc: Mech
MO2 -068
Date: f :; c
Print Name: 1 a. rrx:(J>
This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is
suspended or abandoned for a period of 180 days from the last inspection.
Printed: 05 -03 -2002
iu
2
V) $
N U.
W0
J
a
W .
Z
O :
2 j :
O ;
8 co—
o
W W
W Z
v U
O
ACTIVITY NUMBER: MO2 - 068
DATE: 04 -09 -02
PROJECT NAME: Shearer Residence
SITE ADDRESS: 4433 S 156 St
Original Plan Submittal X Response to Incomplete Letter #
Response to Correction Letter # Revision # After Permit Is Issued
DEPARTMENTS:
Building Division
Public Works
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
Complete Er Incomplete n
TUES /THURS ROUTING:
Please Route ❑ Structural Review Required
APPROVALS OR CORRECTIONS:
Documents/routing slip.doc
2 -2B -02
PLAN REVIEW /ROUTING SLIP
Fire Prevention
Structural
a
PERMIT COORD COPY
Planning Division
Permit Coordinator
DUE DATE: 04-11-02
Not Applicable n
Comments:
Permit Center Use Only
INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED:
Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
No further Review Required
REVIEWER'S INITIALS: DATE:
DUE DATE: 05-09 -02
Approved n Approved with Conditions% Not Approved (attach comments) n
Notation:
REVIEWER'S INITIALS: DATE:
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
I
ACTIVITY NUMBER: MO2 -068
PROJECT NAME: Shearer Residence
SITE ADDRESS: 4433 S 156 St
DATE: 04 -09 -02
Original Plan Submittal Response to Incomplete Letter #
Response to Correction Letter # Revision # After Permit Is Issued
DEPARTMENTS:
Building Division
Public Works
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
Complete
Comments:
Permit Center Use Only
INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED:
Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
TUES /THURS ROUTING:
Please Route
REVIEWER'S INITIALS:
APPROVALS OR CORRECTIONS:
Documents/routing slip.doc
2 -28 -02
n
PLAN REVIEW /ROUTING SLIP
Fire Prevention
Structural
Incomplete n
Structural Review Required
`-
n
n
Planning Division
Permit Coordinator
No further Review Required
DUE DATE: 04-11-02
Not Applicable n
DATE:
DUE DATE: 05 -09-02
Approved (n Approved with Conditions Not Approved (attach comments) n
Notation:
REVIEWER'S INITIALS:
DATE: < < bZ
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
PERMIT NO.: ina
MECHANICAL PERMIT APPLICATIONS
INSPECTIONS
❑ 2
❑ 50
❑ 60
610
700
1080
❑ 1090
❑ 1100
❑ 1101
❑ 1102
❑ 1105
❑ 1115
❑ / 1400
1800
❑ 4015
CONDITIONS
10001 No changes to plans unless approved by Bldg
Div
10002 Plumbing permits shall be obtained through King
Co
10003 Electrical permits obtained through L & I
10005 All permits, insp records & approved plans
available
❑ 10014 Readily accessible access to roof mounted
equipment
10016 Exposed insulation backing material
10019 All construction to be done in conformance
w /approved plans
10027 Validity of Permit
10036 Manufacturers installation instructions required
on site
❑ 10041 Ventilation is required for all new rooms &
spaces
❑ 10042 Fuel burning appliances
❑ 10043 Appliances, which generate....
❑ 10044 Water heater shall be anchored....
Pre - construction
WSEC Residential
WA Ventilation /Indoor AQC
Chimney Installation/All Types
Framing
Woodstove
Smoke Detector Shut Off
Rough -in Mechanical
Mechanical Equipment/Controls
Mechanical Pip /Duct Insul
Underground Mech Rough -in
Motor Inspection
Fire - Final
Mechanical - Final
Special -Smoke Control System
Additional Conditions:
TENANT NAME: 6/'"'"V S.A ieeti °C.
FEES
Basic Fee (Y/N)
Supplemental Fee (Y/N)
Plan Check Fee (Y/N)
Furnace /Burner
to 100,000 BTU (qty)
Over 100,000 BTU (qty)
Floor Furnace (qty)
Suspended/Wall /Floor- mounted Heater (qty)
Appliance Vent (qty)
Heating/Refrig/Cooling Unit/System (qty)
Boiler /Compressor
to 3 HP /100,000 BTU (qty)
to 15 HP /500,000 BTU (qty)
to 30 HP /1,000,000 BTU (qty)
to 50 HP /1,750,000 BTU (qty)
over 50 HP /1,750,000 BTU (qty)
Air Handling Unit
to 10,000 cfm (qty)
over 10,000 cfm (qty)
Evaporative Cooler (qty) •
Ventilation Fan (qty)
Ventilation System (qty)
Hood (qty)
Incinerator — Domestic (qty)
Incinerator — Comm /Ind (qty)
Other Mechanical Equipment (qty)
Other Mechanical Fee (enter $$)
Plan Reviewer:
Permit Tech: v1�. 1 /
C(jJ
Date:
Date:
Z1_
15
Add'l Fees — Work w/o Permit (Y/N)
Insp Outside Normal Hours (hrs)
Reinspections (hrs)
Miscellaneous Inspections (hrs)
Add'I Plan Review (hrs)
Z
rew
V
00
cow
mu_
W O
2 s
to 8 .
O'
uj
2
O N
O I—
W uj
IL Z
U
O
ACTIVITY NUMBER: MO2 -068
PROJECT NAME: GARY SHEARER
SITE ADDRESS: 4433 SOUTH 156 STREET
Response to Correction Letter #
DATE: 04 -02 -02
XX Original Plan Submittal Response to Incomplete Letter #
Revision # After Permit Is Issued
p DE�PARRTMENTS:
u Division p
Public Works ❑
APPROVALS OR CORRECTIONS:
Complete ❑
PERMIT COORD L '
PLAN REVIEW /ROUTING SLIP
hlaP
Structural ❑
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
Documents/routing slip.doc
2 -28 -02
Incomplete
Planning Division
Permit Coordinator
DUE DATE: 4-04 -02
Not Applicable ❑
Comments:
Permit Center Use Only
INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED:
Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
TUES /THURS ROUTING:
Please Route ❑ Structural Review Required ❑ No further Review Required ❑
REVIEWER'S INITIALS: DATE:
DUE DATE: 5-02 -02
Approved ❑ Approved with Conditions ❑ Not Approved (attach comments) ❑
Notation:
REVIEWER'S INITIALS:
DATE:
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
PERMIT COORD COPY
tr y
00
Lu
NLL
w
2
u.
co d
1— 0
z r
• uj
2 p
U
O N
I.-
= W
I— -
�O
0 -
0I
z
ACTIVITY NUMBER: MO2 -068
PROJECT NAME: GARY SHEARER
SITE ADDRESS: 4433 SOUTH 156' STREET
XX Original Plan Submittal
Response to Correction Letter #
DATE: 04 -02 -02
Response to Incomplete Letter #
Revision # After Permit Is Issued
DEPARTMENTS:
Building Division
Public Works
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
Complete ❑ Incomplete
re5 P? Y T I 66 ft
it.-I 7 &I S f r vc..-6 a h 6�
Comments: R V __
TUES /THURS ROUTING:
Please Route ❑ Structural Review Required
REVIEWER'S INITIALS:
APPROVALS OR CORRECTIONS:
Approved ❑ Approved with Conditions
Documents/routing slip.doc
2-28-02
PLAN REVIEW /ROUTING SLIP
Fire Prevention
Structural
REVIEWER'S INITIALS:
Planning Division
❑ Permit Coordinator ❑
DUE DATE: 4 -04-02
Not Applicable ❑
Cer4) t tc CLt e.
nicto 4( ke-- ( tie
Permit Center Use Only
INCOMPLETE LETTER MAILED:
Departments determined incomplete: Bldg ❑
LETTER OF COMPLETENESS MAILED:
Fire ❑ Ping ❑ PW ❑ Staff Initials:
❑ No further Review Required ❑
DATE:
DUE DATE: 5-02 -02
❑ Not Approved (attach comments) ❑
Notation:
DATE:
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections:
Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
ACTIVITY NUMBER: MO2 -068
PROJECT NAME: GARY SHEARER
SITE ADDRESS: 4433 SOUTH 156 STREET
XX Original Plan Submittal Response to Incomplete Letter #
Response to Correction Letter #
DATE: 04 -02 -02
Revision # After Permit Is Issued
DEPARTMENTS:
Building Division
Public Works
Complete ❑
Documents/routing slip,doc
2 -28 -02
PLAN REVIEW /ROUTING SLIP
Fire Prevention
Structural
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
APPROVALS OR CORRECTIONS:
Incomplete
REVIEWER'S INITIALS:
TUES /THURS ROUTING:
Please Route ❑ Structural Revi Required ❑ No further Review Required
REVIEWER'S INITIALS:
DUE DATE: 4 -04 -02
DATE:
Planning Division
Permit Coordinator
Not Applicable ❑
Comments:
Permit Center Use Only
INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED:
Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
DUE DATE: 5 -02 -02
Approved ❑ Approved with Conditions ❑ Not Approved (attach comments) ❑
Notation:
DATE:
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
Project Name /Tenant
(2 c(r ( hec�
1r .
gI.`,Sic 't
Value of Mechanical Equipment:
45
Site Address :
1�s ti 1 LLy: 1
Date: e470I Z.
�/ City tole /
jl )L,,4)drJ ( �
Ta Parcel N ,
`J1(� l0L.SVC / s9
Property Owner: 0
Phone: ( hi) 11vti((65
Fax 0: ( . 3 (
Phone: L%( _
Street Address:
m , A xe. ,
City/State/Zip: t '1� Ar 9pe
Cit St it (
Fax II: (
Contractor:
( 1 im N.
'
Phone: (1,,) /OO
(JU(a 7 a %
Street Address:
A rite
► Slate /Zip:
.—Y. �t:�PS4t -CC rf /t' 4
Fax II: ( )
Contact Person:
„ which .- 6 . i � �
/
� - 199
Phone: L- 40 ) .37J 3•2.
eJ
Street Address:
y State /Zi
Los
Fax II: ( )
if
BUILDING OW - •
• ' 1AU.TH • ' IZE r ENT:
Signature:
OP
Date: e470I Z.
Print name:
et/ & r ru
Phone: ( hi) 11vti((65
Fax 0: ( . 3 (
l
Address: Q � ` �
m , A xe. ,
City/State/Zip: t '1� Ar 9pe
111111111MMEMMErall!li
Project Number:
4
Permit Number:
Mechanical Permit Application
MECHANICAL PERMIT REVIEW AND APPROVAL REQUESTED: (TO BE FILLED OUT BY APPLICANT)
Description of work to be dope (please be specific): ,
. n6 t L2 1:-7 hcQ) ) n r-I-
Current copy of Washington' State Department of Labor and Industries Valid Contractor's License. If not available at the time of
application, a copy of this license will be required before the permit is issued OR submit Form 1.1 - 4, "Affidavit in Lieu of C intractor
Registration ".
Building Owner /Authoriied'Agent: If the applicant is other than the owner, registered architect/engineer, or contractor liter sed by the
Slate of Washington, a notarized letter from the properly owner authorizing the agent to submit this permit application and obtain the
permit will be required as part of this submittal.
I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UN )ER
PENALTY OF PERJURY BY THE LAWS OFJHE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT.
i
CI OF! TL I-'�WILA
Perm4 Center
6301 Sduthcenter Boulevard, Suite 100
TukwIlal WA 98108
(206) 431 -3670
Application and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or facsimile.
Date application accepted :'.
IIn/PP
lurch prrunb.duc
Date application expires:
Expiration of; Plan.Revi pplications which.no permit:is issued within'180 days: following: the da e. of application'sha Il expire
Ilmitation '.The buildin off cial may extend the time-for action' by the applicant for a period not exceeding 180.days upon written
'request by the applicant as I efined in Section 114.4 of the Uniform Mechanical Code (current edition). No application shall be
extended more than on e:
Application taken b ': (initials)
Parcel No.: 8108600258
Address: 4433 S 156 ST TUKW
Suite No:
Tenant: GARY SHEARER
Signatur
Print Name:
doc: Conditions
City of Tukwila
Department of Community Development / 6300 Southcenter BL, Suite 100 / Tukwila, WA 98188 / (206) 431 -3670
` �rrYxnc��z��
PERMIT CONDITIONS
1: ** *BUILDING DEPARTMENT * **
2: No changes will be made to the plans unless approved by the Engineer and the Tukwila Building Division.
3: Plumbing permits shall be obtained through the Seattle -King County Department of Public Health. Plumbing will be inspected by
that agency, including all gas
piping (296 - 4722).
4: Electrical permits shall be obtained through the Washington State Division of Labor and Industries and all electrical work will be
inspected by that agency
(206- 835 - 1111).
5: All permits, inspection records, and approved plans shall be available at the job site prior to the start of any construction. These
documents are to be
maintained and available until final inspection approval is granted.
6: All construction to be done in conformance with approved plans and requirements of the Uniform Building Code (1997 Edition) as
amended, Uniform Mechanical Code
(1997 Edition), and Washington State Energy Code (1997 Edition).
7: Validity of Permit. The issuance of a permit or approval of plans, specifications, and computations shall not be construed to be a
permit for, or an approval
of, any violation of any of the provisions of the building code or of any other ordinance of the jurisdiction. No permit presuming to
give authority to violate
or cancel the provisions of this code shall be valid.
8: Manufacturers installation instructions required on site for the building inspectors review.
I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and ordinances
governing this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provision of any other work or local laws
regulating construction or the performance of work.
MO2 -068
F
Permit Number: MO2 -068
Status: ISSUED
Applied Date: 04/02/2002
Issue Date: 05/03/2002
Date: 53
Printed: 05 -03 -2002
Parcel No.: 8108600258
Address: 4433 S 156 ST TUKW
Suite No:
Applicant: GARY SHEARER
Payee: BLUE DOT SERVICES
TRANSACTION LIST:
doc: Receipt
Amount
Type
Payment Check 01705
ACCOUNT ITEM LIST:
Current Pmts
MECHANICAL - NONRES
PLAN CHECK - NONRES
City of Tukwila
6300 Southcenter BL, Suite 100 / Tukwila, WA 98188 / (206) 431 -3670
RECEIPT
Receipt No.: R020000589 Payment Amount: 51.75
Initials: KAS Payment Date: 05/03/2002 09:19 AM
User ID: 1684 Balance: $0.00
Method Description
Permit Number: MO2 -068
Status: PENDING
Applied Date: 04/02/2002
Issue Date:
51.75
Description Account Code
000/322.100 41.40
000/345.830 10.35
Total: 51.75
•
Printed: 05 -03 -2002
Pro' /
Type of Inspection:
Address: /
'5 ,3 .S' /SP ST .
Date called:
7.2 -OA.
Special: instructions:
Date wanted:
7 - 3-0 Z
a.m.
:-
Requ 4
CC'' lee ee'
Phone:
INSPECTION NO.
CITY OF TUKWILA,BUILDINGDIVISION
6300 #100, Tukwila, WA 98188
COMMENTS:
ector:
No:
roved per applicable codes.
INSPECTION RECORD f17a2 a. e?
Retain a copy with permit
\\(
• 7.1 REINSPECTION FEE REQI Prior to
at 6.00 Southcenter Blvd., Suite 100. Call to sche
r
PERMIT NO.
(206)431 -367
Corrections required prior to approval.
4.
Dat
spection, fee must be paid
ule reinspection.
Date:
CITY Of TUKWILA
APPROYED
APR 1 2 2002
.4,0. AS NOIED
IMVV LDS D \RStO
Patents Pending
OSBURN BAY VISTA
Freestanding Gas - Fired Vented Room Heater
Installation and Operating Instructions
2re Flame of Desire
FILE COPY
I understand that the Plan Check approvals are
to errors and omissions and approval of
not authorize the violation of any
de or ordinance. Receipt of con -
py of approved plans acknowledged.
RECEIVED
CITY OF TUKWILA
APR 022002
PERMIT CENTER
FOR YOUR SAFETY -
WHAT TO DO IF
YOU SMELL GAS
* Open windows
* Extinguish any open flame
* Do not try to light any appliance
* Do not touch any electrical switch
* Do not use any phone in your building
* Immediately call your gas supplier from
a neighbour's phone. Follow the gas
supplier's instructions.
* If you cannot reach your gas supplier
call the fire department.
WARNING
Do not store or use gasoline, or other
flammable vapours and liquids, in the
vicinity of this, or any other appliance.
Improper installation, service,
adjustment, alteration, or maintenance
can cause injury or property damage.
Refer to this manual. For assistance or
additional information, consult a
qualified installer, service agency, or
the gas supplier.
Please read this manual before installing or using this appliance. Retain this manual for future reference.
Made in Canada 05/05/94
frU'2-O8
C ONTENTS
Page
1.0 Introduction 1
1.1 Specifications 1
1.2 Features 3
1.3 Intended Use 3
1.4 General Safety 3
2.0 Operation 4
2.1 Operation Safety 4
2.2 Lighting Instructions 5
2.3 Heat Output Adjustment 7
2.4 Fan Operation 7
2.5 Remote Control Operation 7
2.6 Outside Combustion Air Supply Damper Operation 7
3.0 Installation 8
3.1 Installation & Safety Notes 8
3.2 Unpacking 8
3.3 Installation 9
3.3.1 Minimum Clearances To Combustible Construction 10
3.3.2 Optional Outside Combustion Air Supply Installation 11
3.3.3 Chimney Installation 11
3.3.4 Gas Line Installation 12
3.3.5 Thermostat, Wall Switch, Or Remote Control Installation 12
3.3.6 Firebox Component Installation 15
3.3.7 Initial Firing 17
3.3.7.1 Manifold Pressure Regulator Adjustment 18
3.3.7.2 Pilot Flame Adjustment 18
3.3.7.3 Flue Spillage Test 19
3.3.7.4 Altitude Adjustment 19
4.0 Maintenance
4.1 Maintenance Safety
4.2 Recommended Service
4.3 Glass Cleaning
4.4 Cleaning Of Gold Plated Surfaces
4.5 Burner & Pilot Cleaning
4.6 Fan Replacement & Electrical Schematic
4.7 Heater Disassembly & Reassembly
5.0 Trouble Shooting
6.0 Replacement Parts
7.0 Osburn Limited Warranty
8.0 Label Information
22
22
22
22
22
23
23
24
26
32
35
37
ITEM
NATURAL GAS (NG)
PROPANE (LPG)
INPUT:
35,000 Btu/hr (36.9 MJ/hr)
27,000 Btu/hr (28.5 MJ/hr)
Flue Loss: EFFICIENCY: Fan off
74%
73%
Fan on
78%
78%
OUTPUT: Fan off
26,000 Btu/hr (27.4 MJ/hr)
19,800 Btu/hr (20.9 MJ/hr)
Fan on
27,200 Btu/hr (28.7 MJ/hr)
21,000 Btu/hr (22.1 MJ/hr)
AFUE: EFFICIENCY: Fan off
65%
65%
Fan on
70%
70%
OUTPUT: Fan off
22,900 Btu/hr (24.1 MJ/hr)
17,600 Btu/hr (18.6 MJ/hr)
Fan on
24,600 Btu/hr (25.9 MJ/hr)
18.800 Btu/hr (19.8 MJ/hr)
. 'ivIANIFOLD PRESSURE:
3.5" w.c. (0.87 kPa)
10.5" w.c. (2.6 kPa)
GAS INLET SUPPLY PRESSURE:
Minimum: 5.0" w.c. (1.24 kPa)
Minimum: 13.3" w.c. (4.02 kPa)
Normal: 7.0" w.c. (1.74 kPa)
Normal: 13.3" w.c. (4.02 kPa)
Maximum: 13.5" w.c. (3.36 kPa)
Maximum: 13.8" w.c. (3.44 kPa)
ORIFICE SIZE:
#34 drill ( .111"DIA.) at 0 -4500'
#53 drill (.06 "DIA.) at 0 -4500'
CONTROL VALVE TYPE:
ITT (B67RA05)
ROBERTSHAW 7000 MVRLC
SHIPPING WEIGHT:
145 lb. ( 65.9 kg)
145 lb. ( 65.9 kg)
FLUE OUTLET SIZE:
4 "DIA. (102mm)
4 "DIA. (102mm)
FAN:
2 speed
2 speed
1.0 INTRODUCTION
1.1 SPECIFICATIONS
TABLE 1
Options: Gold plated and colour grille packages
SPECIFICATIONS
/1
29 1/2"
(750 tun)
INSTALLATION CODES
3 1/2"
(89 mm)
•
•
■
l
c
19 3/4"
(502 mm)
A
30 1/4"
(769 mm)
FIGURE 1 Exterior Dimensions
-
•
z
Installation must conform to local codes. In the absence of local codes, installation must conform to the
National Fuel Gas Code, ANSI Z233.1 1988, (in the U.S.), or with the current installation code
CAN /CGA B149.1 - M86 (in Canada). In Australia, the Australian Gas Association installation code for
gas burning heaters and equipment must be used. The heater, when installed, must be electrically
grounded in accordance with local codes or, in the absence of local codes, with the National Electric
code ANSI/NFPA No. 70 -1990 (in the U.S.) or with the current CSA C22.1 Canadian Electrical code
(in Canada).
/2
1.2 FEATURES
Ignition system:
Standing pilot ignition system with thermopile flame detection and piezo igniter.
Gas control:
Gas control valve type:
Automatic millivolt powered combination gas control valve with optional remote on /off
switch, optional wall thermostat, and/or optional remote control. This heater's valve does
not require electric power. The Robertshaw (LPG) valve has in addition a HI/LO flame
control knob, as shown in Figure 3B.
Fan controls:
Automatic/Manual selector switch:
Automatic selection controls fan operation through a heat sensitive switch turning on
when - the: heater ..is:.atoperating:.temperature.
Fan speed selector switch:
• A three position switch providing high speed, off, and low speed operation.
Safety controls:
A safety switch will shut the system down in the event of any one of the following conditions:
Incorrectly installed vent system
Blocked stack causing flue spillage
Flow reversal or sustained downdraft situation
Drafthood:
The appliance is provided with a draft hood design which minimizes the effects of downdrafts
or flue blockages on the quality of combustion. It will vent to the front and rear of the
appliance upon downdraft or flue blockage and, by design, it exhausts to the same pressure zone
as the combustion air inlet to the appliance.
Optional outside combustion air supply
The outside combustion air supply damper may be open during operation and closed when the
heater is not in use.
1.3 INTENDED USE
This appliance is intended to be used as a freestanding heater, when installed as described in detail in
the installation instructions. This heater is suitable for installation in bedrooms where the maximum
input is within 50 cubic feet per 1000 BTU/hr, (ie. 700 cubic feet for NG, 540 cubic feet for LPG).
1.4 GENERAL SAFETY
This vented heater must be properly connected to a venting system in accordance with local codes. This
unit must not be connected to a chimney or flue serving a separate solid fuel burning appliance. It is
equipped with a safety control system (vent safety shut -off system) to protect against improper venting
of flue products. The heater will shut down if no vent is connected, or if there is flue downdraft.
/3
WARNING: Operation of this heater when not connected to a properly installed and maintained
venting system, or any tampering with the safety shutoff system may result in carbon
monoxide poisoning and possible death.
Installation and repair should be done by a qualified service person. The appliance should be inspected
before use and at least annually by a professional service technician.
Provide adequate clearances around air openings into the combustion chamber and allow accessibility
clearance for servicing and proper operation.
2.0 OPERATION
PILOT
ASSY
PULL FOR
ACCESS TO
U1BELS
2.1 OPERATION SAFETY
L CONTROL PANEL
ASSEMBLY
DAMPER CONTROL
(UND€R)
IMO IGNITION BUTTON
I ACCESS DOOR GRILLE
ON OPEN POSnTON)
FIGURE 2 Operation Controls
NIGH
OFF
LOW
MANUAL
AUTO
Inspect the heater before use. Always keep the appliance area clear and free from combustible materials,
gasoline and other flammable vapours and liquids. Never obstruct the flow of combustion and
ventilation air. Keep the front of the appliance clear of all obstacles and foreign materials. Never
obstruct or modify the air inlet/outlet grilles of the fireplace in any manner.
4 4 ,..::,...
/4
Children and adults' should be alerted to the hazards of high surface t�1,iperature and should stay away
to avoid bums or contact with hot surfaces. Young children should be carefully supervised when they
are in the same room as the heater. Clothing or other flammable material should not be placed on or
near the heater.
The glass panel and louvres must be properly installed prior to operation. Never operate the heater with
the glass panel off or broken since this may cause dangerous indoor air pollution. This heater is not for
use with solid fuel. z
2.2 LIGHTING INSTRUCTIONS
0
co
"FOR YOUR SAFETY, READ BEFORE LIGHTING" co ILJ
w 0
2
"WARNING: If you do not follow these 4 a
instructions exactly, a fire or explosion may
result causing property damage, personal w
injury or loss of life." z
�
z I-
Lu
"A. This appliance is provided with a standing pilot flame. When lighting the pilot, follow
PP P gP g g P o
w
- 0
"B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next LL z
to the floor because some gas is heavier than air and will settle on the floor. v
0
these instructions exactly :"
WHAT TO DO IF YOU SMELL GAS
* Do not try to light any appliance.
* Do not touch any 'switch: do not use any phone in your building.
* Immediately call your gas supplier from a neighbour's phone. Follow the gas
suppliers instructions.
* If you cannot reach your gas supplier, call the fire department."
"C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob
will not push in or turn by hand, do not try to force or repair it, call a qualified service
technician. Forcing or attempted repair may result in a fire or explosion."
"D. Do not use this appliance if any part has been under water. Immediately call a qualified
service technician to inspect the appliance and to replace any part of the control system
and any gas control which has been under water."
/5
z
LIGHTING PROCEDURE
1. "STOP!" Read the safety information in the previous section.
2. Set the thermostat to lowest setting.
3. Turn off all electrical power to the appliance.
4. Open the access door grille, hinged to open downward, by pulling the top grille
toward you.
5. Push in the gas control knob slightly and turn clockwise to the "OFF"
position as shown in Figure 3A below.
t IM ��
I mumps
0 1400
OAS OO TIR
IOC.
ROT
AWSII6rt
FIGURE 3A ITT Control Valve
N.G. Only
FIGURE 3B Robertshaw Control
Valve L.P.G. Only
6. Wait a minimum of five minutes to clear out any residual gas. If you then smell
gas, STOP! Follow "B" in the Lighting Instruction section described on the
previous page. If you don't smell gas, go to the next step.
7. Press in the valve knob and turn counterclockwise f\ to the "PILOT" position.
8. Push in the control knob all the way and hold it in. Immediately push the piezo
ignition button (the red button to the left) repeatedly so that it clicks; continue
until the pilot ignites. Maintain pressure on the control knob for about one minute
after ignition. Then release the control knob; if the pilot flame goes out repeat
step 8; if the pilot flame remains on then turn the valve knob counterclockwise
f ' to the "ON" position.
9. If the pilot lights, but will not stay on after several tries, turn the gas control knob
to the "OFF" position and call your service technician or gas supplier. If the
control knob does not pop out when released, STOP - shut off the gas supply to
the control valve, and IMMEDIATELY call your service technician or gas
supplier.
10. Close the access door grille by lifting it and allow the springs to pull it closed.
11. If equipped with an on /off side shield or wall switch, select the "ON" position.
If equipped with a thermostat or auxiliary control, set it to the desired setting.
/6
.. 'n.at. •i'.1a14n:
X.'2:A'+S%+'.k•'�3<i,.;'tt ilu��:: '41,%$J4''`'
2.3 HEAT OUTPUT ADJUSTMENT
The ITT valve control can be used to decrease the heat output and flame height from maximum to a
partially reduced level by turning the gas control knob clockwise (\ . Always operate the unit with
a minimum of at least '.1.: 'of flame-.height:_- - :The• •Robertshaw valve (LPG) uses the HI/LO knob,
previously described, to control the heat output and flame height.
SHUTDOWN PROCEDURE
1. To turn off the main burner only, turn off the wall switch, thermostat, or On /Off
switch located on the side shield.
2. The pilot will remain lit, ready for main burner relighting.
3. For complete shutdown of the appliance, depress the valve control knob and turn
it clockwise (\ to the "OFF" position.
2.4 FAN OPERATION
The fan control switches are located behind the access door grille assembly and may be selected to the
following settings:
Automatic or Manual: (lower switch)
When set to automatic, the fan will come on when the unit reaches operating
temperature.
High, Off, or Low speed: (upper switch)
When the switch is pushed up, the fan will be on high speed; in the middle
position off, and when pushed down, on low speed.
2.5 REMOTE CONTROL OPERATION
An optional hand held remote control kit for turning the unit On and Off, is also available. Detailed
instructions for the optional Remote Control are included with the kit.
2.6 OUTSIDE COMBUSTION AIR SUPPLY DAMPER OPERATION
If outside air is being supplied the damper may be opened during operation and closed when the heater
is not in use.
1. To close the damper, push the damper control handle in towards the rear of the unit as
shown in Figure 4 on the following page.
2. To open the damper, pull the damper control handle out towards the front of the unit.
/7
3.0 . INSTALLATION
OPEN
DAMPER CONTROL
HANDLE (UNDER)
FIGURE 4 Damper Operation
3.1 INSTALLATION & SAFETY NOTES
Read all instructions before starting installation and follow them carefully during installation to ensure
maximum benefit and safety. Failure to follow these instructions will void your warranty and may
present a fire hazard. See the Osburn warranty at the back of this manual for improper installation
disclaimers. This unit and its components are tested and safe when installed in accordance with this
installation manual.
ELECTRICAL GROUNDING NOTE: This heater fan is equipped with a three -prong (grounding) plug
for your protection against shock hazard and should be plugged directly into a properly grounded three -
prong receptacle. Do not cut or remove the grounding prong from this plug.
WARNING: Do not connect 120 VAC to the gas control valve or its wiring, as this will damage the
valve.
3.2 UNPACKING
The heater is shipped with the logs, vermiculite, and glowing ember wool in separate packages inside
the firebox. All other parts of the unit are in place.
Report to your dealer any parts that may have been damaged in shipment (specifically check the glass
condition).
The pedestal rear cover will need to be removed from the unit prior to connecting the gas line. The best
time to install the internally packaged parts is after connection of the gas line. The louvre assembly and
glass panel need to be removed before installation of the vermiculite, glowing ember wool, and logs.
/8
1. Note the position of the louvre assembly before removing. Hold the glass against the unit
while removing the Phillips screw located above the centre of the glass as shown in
Figure 5A below.
FIGURE 5A
3.3 INSTALLATION
NOTE: ALL INSTALLATIONS REQUIRE VENTING.
COOKTOP FRONT EDGE
FIGURE 5B
2. Carefully tilt the louvre assembly and glass panel toward you until it clears the front edge
of the cooktop, as shown in Figure 5B above.
3. Gently lift the panel, edge trims, and louvre assembly out of the bottom glass retainer as
a unit. Handle the glass and trim very carefully and set it in a safe place, away from
traffic, .areas.
NOTE: THE ONE PIECE GLASS IS VERY FRAGILE AND IS EXPENSIVE TO REPLACE. DO
NOT MOVE THE HEATER WITH THE GLASS IN PLACE AFTER THE INITIAL
UNPACKING IS DONE.
4. Remove the packaging containing the logs, vermiculite, and glowing ember wool.
In planning the installation it is necessary to install certain items before the unit is completely positioned
and installed. These include the optional fresh air supply, the vent system, the gas piping, and the
wiring.
/9
3.3.1 MINIMUM CLEARANCES TO COMBUSTIBLE CONSTRUCTION
A. Sidewall 8" (203.2mm) measured to unit
B. Backwall 1" (25.4mm) measured to unit
C. Ceiling 40" (1015mm) to top louvre
D. Floor Install directly' on combustible floor, see Figure 6 below.
E. Corner 1" (25.4mm) measured to unit
40"
(1016 mm)
V
C
FIGURE 6
/10
.i.e afst: A: ..:'t;44.k4'_r.;::4t2: +YdC+.:
3.3.2 OPTIONAL OUTSIDE COMBUSTION AIR SUPPLY INSTALLATION
Supply a 4" (102mm) diameter flex aluminum pipe or equivalent from the outside to the lower rear of
the pedestal centre. A knockout has been provided in the pedestal rear cover for this purpose.
Alternately the pipe may come through the floor under the pedestal base, which has been provided with
a 4" (102mm) diameter air passage.
3.3.3 CHIMNEY INSTALLATION
Figure 7 below shows a completed installation.
FIGURE 7 Chimney Installation
The unit must be connected to a liner or vent suitable for use with gas. The liner must run within the
existing chimney from the outlet collar of the drafthood to the top of the masonry or factory built
chimney. Install the liner or vent according to the manufacturer's instructions. Install sufficient height
of vent to result in adequate draft, as determined by a flue spillage test.
Use a maximum of two offsets (4 -45° elbows), or two 90° elbows. Slope horizontal pipe at least 1/4"
(6.4mm) rise per foot of run. Horizontal runs should not exceed the vertical rise.
Follow "B" vent installation instructions. Secure the "B" vent with the three screws provided at each
joint, but DO NOT penetrate the inner wall.
/11
W
0 0
to
co w
co O
W
J
u_ Q'
W
z
F-
z 1-
W ui
2
0 N
0 F -
= v
L I o
w z
co
0 F-
z
AWG
mm
ft.
m
14
1.6
100
30.5
16
1.3
64
19.5
18
1.0
40
12.2
20
0.8
25
7.6
7 7
_ 0 6
10
1 1
3.3.4 GAS LINE INSTALLATION
Install supply line using flexible gas line such as listed gas appliance connectors meeting CAN /CGA
6.10, AGA 3, ANSI Z21.24 or Z21.45, or any other approved piping method. A qualified service
technician should install the gas line in accordance with all local building codes. If codes permit, flex
gas line or coiled copper tubing may be used for gas supply.
A 1/8" (3.2mm) NPT plugged tapping is provided on the outlet side of the gas control for a test gauge
connection to measure the manifold pressure.
This heater must be isolated from the gas supply piping system by closing its individual manual shut off
valve during any pressure testing of the gas supply piping system at test pressures equal to or less than
1/2 psig (3.45 kPa).
The heater and its individual shut off valve must be disconnected from the gas supply piping system
during any pressure testing of the system at test pressures in excess of 1/2 psig (3.45 kPa).
Provide a required 1/8" (3.2mm) NPT plugged tapping immediately upstream of the gas supply
connection for inlet pressure measurement. The plugged tapping may go on a 2" (50mm) long 3/8"
(9.5mm) NPT nipple which is connected to the elbow. Connect the other half of the union to the nipple.
3.3.5 THERMOSTAT, WALL SWITCH, OR REMOTE CONTROL
INSTALLATION
The thermostat must be CSA or UL approved. Osbum supplies an optional thermostat. If used, a wall
switch may be purchased locally' as Osbum does not supply this item. The switch need only be rated
for millivolts, not 120 VAC. The two supplied blue lead wires that run from the valve of the heater to
the right outside are to be connected to a thermostat, wall switch, and/or remote control.
1. Mount the Thermostat, Wall Switch, or Remote Control Receiver in the desired location
and run "two conductor thermostat wire" to the heater's lower right hand corner, close
to the gas supply line. Purchase "two conductor thermostat wi'r'e," which is not
provided, at any local supplier. The gauge of thermostat wire will determine the
maximum distance at which to locate the thermostat or wall switch. See Table 2 below
and the information packaged with thermostat.
TABLE 2 THERMOSTAT WIRE INFORMATION
WIRE SIZE
MAX. LENGTH
/12
TO TEST
CONNECT
METER LEADS
TO.TERMINALS
THERMOSTAT
CONTACTS
METER
READING
SHOULD BE
COMPLETE
SYSTEM
A .& D
CLOSED ' "
OVER 140 mV
THERMOPILE
OUTPUT
A & B
OPEN
OVER 140 mV
THERMOSTAT
OUTPUT
C & D
CLOSED
UNDER 20 mV
•
TABLE 3A
2. While the heater is being installed and the gas line is connected, attach the thermostat
wire to the two blue 1/4" (6.4mm) insulated female spade connector wires. The
thermostat switch may be connected in parallel with a wall switch, or remote control as
shown in Figures 8A & 8B on the following pages.
3. Check tests can be performed on the two valve types by using the millivolt checkout
Tables 3A & 3B on the following pages.
ITT VALVE MILLIVOLT CHECKOUT
FIGURE 8A ITT Valve Wiring (NG)
re w
00
N o
w
J
Nu-
w 0
u Q
co 3
w
° ,
0—
D F-
w W
O
w z
v=
0
z
TO TEST
CONNECT
METER LEADS
TO TERMINALS
THERMOSTAT
CONTACTS
METER
READING
SHOULD BE
COMPLETE SY
STEM
2 & 3
CLOSED
GREATER
THAN 100 mV
THERMOPILE
OUTPUT
1 & 2
OPEN
GREATER
THAN
325 mV (CP -2)
SYSTEM
RESISTANCE
. 1 & 3
CLOSED
LESS THAN
80 mV (CP -2)
AUTO/PILOT
DROPOUT
1 & 2
OPEN
BETWEEN
120 - 30 mV
1
TABLE 3B ROBERTSHAW VALVE MILLIVOLT CHECKOUT
TERMINAL
aa.ao _Araa1oa. %own
u auaar
FIGURE 8B Robertshaw Valve Wiring (LPG)
/14
I,
INSTALLING LOGS
3.3.6 FIREBOX COMPONENT INSTALLATION
Proper log placement is very important. The logs are designed to be installed in only one
position so that flames do not impinge on them.
1. Place the front and rear lower logs as shown in Figure 9 below:
FIGURE 9 Installing Logs
2. Brick panels provide the side to side positioning of the lower logs.
3. Place the upper left log on top of the two lower logs ensuring that the split log
knot is to the rear of the firebox and the alignment knobs fit into the recesses in
the lower logs.
4. Place the upper right log against the rear brick panel, on top of the upper left and
front logs, so that it curves toward the rear of the firebox and does not rotate.
Ensure that alignment. knobs fit into the recesses in the other logs as shown in
Figure 9 above.
FIGURE 10 Final Log Position
/15
5. Verify that the placement of the factory installed brick panels and baffle is as
follows:
INSTALLING VERMICULITE
* The baffle rear flange should be behind the rear brick panel and the
baffle should rest on top of the side brick panels.
* The brick panels should be up against the firebox sides and as far
back to the rear of the firebox as possible.
Open the bag of vermiculite and spread it evenly on the firebox bottom, around each side, and
in front of the firegrate as shown in Figure 11 below. Do not obstruct any air holes around the
burner. Do not place vermiculite on the rockwool tray, which is located in front of the front
lower log.
FIREBOX BOTTOM FIREGRATE
FIGURE 11 Installing Vermiculite
INSTALLING GLOWING EMBER WOOL
The glowing ember wool should be placed along the rockwool tray located behind the burner as
shown in Figure 12 below. Ensure that the glowing ember wool does not block the air space
between the rockwool tray and the burner tube. Do not place the wool on top of the burner tube.
Any excess glowing ember wool should be used as replacement material during subsequent
servicing.
VERMICULITE
Us' MIN. GAP ROCKWOOL'IRAY
FIGURE 12 Installing Glowing Ember Wool
/16
. +7
V:pNkT.1
i,,Z,C ;:ti:i :;w:.•r.•.
INSTALLING THE GLASS & LOUVRE ASSEMBLY
Before installing the glass, inspect the top glass support gasket, (shown in Figure 13 below) to
ensure a tight seal between the glass and the heater will be possible. Any leakage in the seal
will result in combustion products entering the room. The top glass support gasket must be in
good condition. The front top edge of the firebox and the rear edge of the top glass support must
be straight and free from dents.
3.3.7 INITIAL FIRING
FIGURE 13 Gasket Inspection
GASKET
ti
See section 3.2 and follow the reverse of the glass and louvre assembly removal procedure. Push
down on the bottom of the louvre assembly to ensure that it is tight to the glass before tightening
the louvre assembly mounting screw. After tightening, a precautionary check for leaks can be
made using an electronic gas detector or carbon monoxide meter. If necessary inject high
temperature (600° F.) silicone sealer up into the right and left corner cavities of the top glass
support.
When lit for the first few times, the appliance may emit an odour resulting from evaporation of paint
and lubricants used in the manufacturing process. Open a door or window for ventilation. Anyone with
a respiratory condition may need to leave the room during the initial firings.
Occasionally, after a cold start, vapour may condense and fog the glass, and the flames may be partially
blue. After a few minutes the moisture will disappear and after several minutes the flames should
become yellow.
/17
3.3.7.1 MANIFOLD PRESSURE REGULATOR ADJUSTMENT
The manifold pressure regulator controls gas input and flame height, and is preadjusted at the factory.
No further adjustment is normally required.
On the Robertshaw valve, flame and manifold adjustment is not necessary and is not recommended.
On the ITT valve, the regulator can be adjusted as follows:
1. Open the access door grille.
2. Pull the gas control knob off and unscrew the two Phillips screws holding the control
panel assembly. Remove the control panel.
3. Connect a manometer to the manifold pressure tap on the valve.
4. Remove the regulator adjustment cover screw from the valve, as shown in Figure 3A of
section 2.2, to expose the adjustment screw.
5. Turn the regulator adjustment screw to achieve the desired setting.
6. Replace the regulator adjustment cover screw, the plug in the manifold pressure tap,
control panel assembly, and the gas control knob.
3.3.7.2 PILOT FLAME ADJUSTMENT
For proper operation, the pilot and main burner flame characteristics must be steady and not lifting off
or floating. The top 1/2 " -3/4" (13 -19mm) of the thermopile should be engulfed by the pilot flame. The
pilot flame adjustment should be performed by a qualified service person only. To adjust the pilot flame,
remove the control panel assembly as described previously and remove the pilot adjustment cover screw
shown in Figures 3A and 3B of section 2.2, to expose the pilot adjustment screw. Turn the pilot
adjustment screw counter- clockwise /r"\ to increase, and clockwise (\ to decrease the flame.
Ensure that the pilot flame completely engulfs the thermopile, as shown in Figure 14 below. Replace
the cover screw.
INCORRECT FLAME
CORRECT FLAME
FIGURE 14 Pilot Flames
3/8" TO 1/2"
(10mm TO 13mm)
/18
tud.'[ �3r ii: +e�i:jiN.l.'�!:�.���JY ue.'s: � ^' -iit t. "i:4`vn:`a,: 5:.#':i. �:i >k4Sia+i'.l•L':(:+.ti:' r4i�3'�rJts's`�l;E
3.3.7.3 FLUE SPILLAGE TEST
A flue spillage test is recommended as part of this installation and should be'performed by a qualified
service person only. Hereafter, periodically check the vent draft.
1. Close all the doors and windows in the room.
2. Start all the exhaust fans in the home.
3. Light the heater to the full fire position.
4. After five to ten minutes, insert a match under the 2nd louvre as shown in Figure 15
below, and ensure that the flame wisps and smoke are drawn into the ducts at the front
corners.
5. If the flame .wisps..are.not•.drawn-into .the ducts, turn the heater off, and determine the
cause of the lack of draft. Do not operate the heater until there is sufficient draft.
INSUFFICIENT DRAFT
3.3.7.4 ALTITUDE ADJUSTMENT
FIGURE 15 Flue Spillage Test
SUFFICIENT DRAFT
All valves have been pre -set and certified for installation at elevations from 0 - 4500 feet (1- 1370m)
above sea level.
When installing this heater at higher elevations, it is necessary to decrease the input rating, either by
changing the existing burner orifice to a smaller size, or by reducing the manifold pressure. To adjust
the pressure, see section 3.3.7.1. Input should be reduced 4% for each additional 1000 feet above sea
level.
/19
ALTITUDE
up to (ft)
REDUCTION
( %)
ORIFICE SIZE
TARGET
INPUT
MANIFOLD
PRESSURE
(in. wc)
4500
-
53
27,000
10.5
5500
4
36
25,920
6500
8
37
24,840
7500
12
54
23,760
8500
16
38
22,680
950
20
39
21,600
10500
24
55
20,520
11500
28
42
19,440
ALTITUDE
up to (ft)
REDUCTION
( %)
ORIFICE SIZE
TARGET
INPUT
MANIFOLD
PRESSURE
(in. wc)
4500
-
34
35,000
3.5
5500
4
36
33,600
' 6500
8
37
32,200
7500
12
37
30,800
8500
16
38
29,400
950
20
39
28,000
10500
24
41
26,600
11500
28
42
25,200
To derate the heater for Canada, use Tables 4A, 4B, 5A & 5B shown on the following pages or check
with the local gas authorities for proper orifice size identification. For the USA, derate the heater from
sea level according to the gas installation code.
TABLE 4A ALTITUDE ADJUSTMENT BY CHANGING
ORIFICE (NATURAL GAS ONLY)
TABLE 4B ALTITUDE ADJUSTMENT BY CHANGING
ORIFICE (PROPANE/LP GAS ONLY)
/20
4.5 BURNER & PILOT CLEANING
Periodic cleaning is necessary for proper operation.
1. Refer to section 4.7, remove the burner and check to make sure that the burner orifice is
clean.
z
2. Visually inspect the pilot. Brush or blow away any dust, lint or foreign debris. If the
pilot orifice is plugged, disassembly may be required to remove any foreign material from c
the orifice or tubing. When the appliance is back in service, check the burner flame
pattern with the Pilot Flame Figures in section 3.3.9.1. For relighting, refer to the v
00
lighting instructions in section 2.2. N W
9
N O
4.6 FAN REPLACEMENT & ELECTRICAL SCHEMATIC W
J
1. Turn off all electrical power to the heater. N
w
' 2. Refer to section 4.7 and remove the firebox components. z
1-0
3. Remove the fan cover at rear of cavity by removing the three screws. 111 '
D O
4. Disconnect the fan wiring, remove the fan assembly, and replace or service it as required. p N
ot-
w —
5. Reassemble in reverse order. v
.L.O
6. See Figure 16 on the following page for fan electrical schematic. iu z
U N
7. If necessary, the Fan Thermal Switch behind the right hand grille may be replaced as z
follows:
1. ..Ensure`the.fa - switches.are:in..the "OFF" and "MANUAL" positions.
2. Remove the right hand grille assembly.
3. Pull the fan thermal switch mount bracket out from the bottom.
4. Disconnect the two wires from the switch.
5. Remove the two screws securing the switch.
6. Reassembly in the reverse order.
/23
4
GRN
BUf /Not
WH /NEUT
RED/LOW
AUTO
(A
FIGURE 16 Fan Electrical Schematic
4.7 HEATER DISASSEMBLY & REASSEMBLY
The following procedure is to be performed by qualified service personnel ONLY.
Turn off the gas supply and allow the heater to cool for up to 30 min.
Refer to steps 1 -3 of Unpacking section 3.2.
CAUTION: The screw located above the top centre of the glass just below the louvres, may be
damaged if removed while the heater is still hot.
1. Remove the logs, vermiculite, and glowing ember wool.
2. Remove the firegrate.
3. Remove screws 1 thru 4 from the firebox bottom and the front burner duct.
4. Remove the burner by lifting up and sliding it over so that the venturi leg passes through
the notch for the pilot assembly.
5. Note the position of the cover plate, and unscrew the remaining ten screws from the
firebox bottom as shown in Figure 17 on the following page.
/24
DETAIL A
AIR HOLE FULLY COVERED
FOR USE WITH N.G. ONLY
DETAIL B
AIR HOLE PARTIALLY OPEN
FOR USE WITH L.P.G. ONLY
FIGURE 17 Firebox Bottom Removal
6. Pull forward and lift out the firebox bottom and perform required service.
7. Reinstall the firebox bottom.
8. Reassemble the remaining components in reverse order.
/25
5.0 TROUBLE SHOOTING
SYMPTOM
I. Pilot will not light
after repeated
triggering of the red
piezo ignition button
POSSIBLE CAUSE
A. No spark at electrode (weak
or no heat source for pilot
ignition)
1. Improper ignition
2. Poor connections at starter
and ignition electrode
3. Broken ceramic cover on
ignition electrode
4. Defective piezo igniter
5. Poor grounding of piezo
igniter
B. No gas or low gas pressure
1. Gas line shut off(s) may not
be turned on
2. No gas supply (LPG)
3. Air in gas lines
4. Gas lines may not be
connected
CORRECTIVE ACTION
1. Align the electrode with 1/8"
gap to pilot hood
2. Reconnect if loose
3. Replace pilot assembly
4. Replace piezo igniter
5. Tighten mounting nut and/or
igniter screws
1. Turn on shut -off valves
2. Check propane tank, you may
be out of fuel
3. Purge gas lines
4. Connect all gas lines
5. Low pressure may be caused 5. Check for a kinked line
by bent line
/26
SYMPTOM
I Pilot will not light
after repeated
triggering of the red
piezo ignition button
(Continued)
II. Pilot will not stay lit
after following the
lighting instructions
POSSIBLE CAUSE
B. No gas or low gas pressure
(Continued)
6. Valve control knob not fully
depressed in "PILOT"
position.
7. Too narrow diameter of pipe
or low line pressure
8. Pilot adjustment fully closed
9. Blockage of pilot line or
orifice
A. Thermopile / valve
1. Weak or improperly located
pilot flame
2. Defective thermopile
3. Overheated thermopile
4. Thermopile not installed
properly
5. Open wire connection in
pilot circuit
CORRECTIVE ACTION
6. Fully depress control knob.
7. Consult with a plumber
(fitter) or your gas supplier
8. Adjust as required
9. Check and clean
1. Adjust and clean pilot. The
flame must impinge on or
engulf the thermopile, as
shown in Figure 14
2. Replace thermopile.
3. Provide cooling and make
sure no foreign objects are in
the way.
4. Make sure all wire
connections at the gas valve
terminals are tight and the
thermopile is fully inserted
into the mounting bracket.
5. Check wire continuity and
connections in the pilot
circuit, including the white
wires to the spill switch.
/27
, AveyV.'d>Wan{yesn t Vf..P-Fi:fdii?
SYMPTOM
II. Pilot will not stay lit
after following the
lighting instructions
(Continued)
HI. Main burner will
not light
POSSIBLE CAUSE
A. Thermopile/valve
(Continued)
6. Defective valve
D Defective safety circuit
1. Improperly wired
2. Loose or defective
connections
3. Defective spill switch
4. Defective electromagnet
power unit (EPU)
A. Valve / Switches
1. Valve control off
2. Blockage at the burner
(line, orifice, or ports)
CORRECTIVE ACTION
6. Connect the millivolt meter
probes to the thermopile
terminals on the gas valve.
Turn the valve to the
"PILOT" position, depress
and light. If the meter
reading is greater than 250
millivolts after 30 seconds,
the thermopile is good. If the
pilot does not stay lit, the
valve is defective. Check
section "B" below, before
replacing valve.
1. Rewire correctly
2. Check continuity, tighten
wiring or connections and
repair
3. Check continuity and replace
if defective
4. Check and replace if required
1.
Turn to "ON" position
2. Check and clean
/28
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
i Main burner will
not light
(Continued)
A. Valve / Switches
(Continued)
3. Defective wall switch or
thermostat
4. Defective wiring or
connections
5. Too long a run with
thermostat wire. from •valve
to wall switch or
thermostat
6. Wall switch or thermostat
incorrectly wired
7. Defective remote control
8. Mismatched remote control
frequencies
9. Defective valve
3. Conduct a continuity test or
jumper wire test and
replace if defective
4. Conduct a test with a
jumper wire and repair as
required
5. Reduce wire length to less
than 100 feet, or increase
wire size.
6. Wire correctly
7. Check batteries and replace
if required
8. Match frequencies
9. Turn valve and "ON /OFF"
switch to the "ON"
position. Check with
millivolt meter at terminals
2 & 3 (Robertshaw) and A
& D (ITT). Millivolt meter
should read greater than
100 millivolts (Robertshaw)
and 140 millivolts (ITT). If
the reading is ok and the
burner does not come on,
replace the gas valve.
re ILI,
00
N
N w
w
2
gQ
d
z
O
w
0
0 -
0
w W
u_ 17
wz
0-
01-
z
SYMPTOM
III. Main burner will
not light
(Continued)
W. Soot deposits on
glass
POSSIBLE CAUSE
A. Valve / Switches
(Continued)
10. Thermopile may not be
generating sufficient
voltage (140 mV ITT &
325 mV Robertshaw).
11. Wall switch, thermostat,
remote control, or wires
are defective
1. Flame impingement on
logs
2. Improper venturi setting
3. Vermiculite or ember wool
impeding burner
4. Air inlet blocked or
restricted
5. Vent system is restricted
or inadequate
6. Baffle is out of position
CORRECTIVE ACTION
10. Recheck using the millivolt
meter. The pilot flame may
not be close enough for the
flame to properly engulf the
thermopile. If so, adjust and
retest. If voltage is still
insufficient, replace
thermopile.
11. Follow previous corrective
action, check switch and
wiring. Replace where
defective
1. Adjust the log set to avoid
direct flame impingement.
Follow log placement
instructions
2. Ensure the air shutter is
wide open
3. Ensure that no foreign
material blocks burner
flame ports
4. Clean air inlets
5. Conduct flue spillage test
and correct flue as required
6. Ensure baffle is correctly
positioned towards the back
of the stove
/30
ITEMS
DESCRIPTION
PRODUCT
CODE
INDIVIDUAL
Louvre - Met. Black
BVTLP
TOP LOUVRES
Top Louvre - Gold Plated
BVTLG
Large Grille - Met. Black
BVCGP
Side Grille - Met. Black
BV6GP
Large Grille - Ebony
BVCGE
Side Grille - Ebony
BV6GE
Large Grille - Forrest Green
BVCGF
INDIVIDUAL
Side Grille - Forrest Green
BV6GF
BOTTOM
Large Grille - Ivory
BVCGI
GRILLE
Side Grille - Ivory
BV6GI
COMPONENTS
Large Grille - Gold Plated
BVCGG
Side Grille - Gold Plated
BV6GG
GLASS
One Piece Ceramic Glass Panel
BVCG
Log Set - Complete
BVLSC
CERAMIC
Top Left Log
BVTLL
FIBRE LOGS
Top Right Log
BVTRL
Bottom Front Log
BVBFL
• Bottom Rear Log
BVBRL
REFRACTORY
Refractory Set - Complete
BVRSC
PANELS
Back Refractory Panel
BVBRP
Left Refractory Panel
BVLRP
Right Refractory Panel
BVRRP
/33
ITEMS
DESCRIPTION
PRODUCT
CODE
BURNER/VALVE
PARTS AND
RELATED
ACCESSORIES
Burner - Natural Gas or Propane
ITT Automatic Valve Assemblies- Natural Gas
Robertshaw Automatic Valve Ass'y.- Propane
Thermopile
Piezo Igniter
Pilot Assembly - Natural Gas
Pilot Assembly - Propane
Pilot Line
Thermodisc Spill Switch
Natural Gas Conversion Kit (LPG to NG)
BVBNG
BC4L
BC4M
G1030
G1040
BV 1041 N
BV 1041 P
BV 1042
BC4L303
BC4L6
FAN
MISC.
ELECTRICAL
ITEMS
Fan Assembly
Fan Snap Disc
Fan Switch -
2 position (Auto,/Man)
Fan Switch -
3 position (Hi/Low /Off)
Burner Switch - Gold Tip,
2 position (On/Off) mounted on side shield
BC4N1
BC4N502
FRS
BVFRS
BN7DO1
MISC.
FIREBOX
COMPONENTS
Glowing Ember (package)
Vermiculite (package)
Spill Switch Assembly
Baffle
Pipe Adaptor Assembly
BVE
BVV
BS4L3
BC2C
BSI 1 A
/34
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
Flame burns blue
and lifts off
burner
VI. Frequent pilot
outage problem
•
VII. Flames impinge on
baffle
1. Insufficient combustion air
being supplied
2. Manifold pressure set too
high
1. High limit switch is
defective or has reached its
maximum temperature
1. Baffle is out of position
2. Vent system is restricted
or inadequate
3. Manifold pressure set too
high
1. Ensure that no foreign
material blocks air inlets
and that the shutter is wide
open. Ensure the vent is
adequate.
2. Check and adjust manifold
pressure.
1A. Allow the unit to cool; then
repeat lighting instructions
1B. If IA above does not allow
ignition, place jumper wires
across the high limit switch.
If you can re- ignite the
pilot, the high limit switch
is defective. Do not use
the fireplace until the high
limit switch is replaced. If
the unit does not light with
the jumper wires in place,
the wires or the connectors
may be defective.
1. Ensure baffle is correctly
positioned.
2. Conduct flue spillage test
and correct flue as required.
3. Check and adjust manifold
pressure as required.
/31
DESCRIPTION
PRODUCT
CODE
Thermostat, White Rodgers
G1011
Remote Control
GRC
6.0 REPLACEMENT PARTS
When requesting service or replacement parts for your fireplace, please provide model number and serial
number. All parts listed below may be ordered from an authorized dealer.
TABLE 6 REPLACEMENT PARTS
BOTTOM GRILLE ASSEMBLIES
Includes (2) sides and (1) access door grille
BLACK METALLIC ASSEMBLY
COLOURED ASSEMBLY
GOLD ASSEMBLY
BGAP
BGA(E,I,F)
BGAG
NOTE: Colour code designation (E) Ebony, (I) Ivory, (G) Gold, (F) Forrest Green
BAY VISTA ACCESSORIES
/32
•
1
7.0 OSBURN LIMITED WARRANTY
LIMITED WARRANTY
This Limited Warranty is made by Osburn Manufacturing Inc., 555 Ardersier Road, Victoria, B.C.,
Canada, V8Z 1C8, hereinafter referred to as the "Warrantor ". The Warrantor guarantees to the original
consumer that the firebox and heat exchanger components of its gas burning fireplaces and stoves will 1
be free from defects in materials and workmanship, under normal use and service, for a period of five
re 2
years from the date of purchase. All other components are covered for one year from the date of
purchase. The only items excluded from this warranty are paint, gold plating, and glass. Use of any N 0
components not supplied by Osburn will void warranty. c
Osburn disclaims any responsibility for the following actions, any of which will void the warranty: w 0
NOTE: SUCH ACTIONS MAY CAUSE A FIRE HAZARD g j
— o
* Installation of any damaged fireplace or chimney component, LLI
* Modification of the fireplace or vent system, F.
* Improper positioning of the gas logs or the glass, z 0
* Installation and/or use of any component part not manufactured or approved by Osburn
Manufacturing Inc., not withstanding any independent testing laboratory or other party v
approval of such component part or accessory. o
=w
OBTAINING WARRANTY SERVICE
u = o
To obtain warranty service, the consumer shall return the defective part to the original selling dealer,
transportation prepaid, along with the serial number of the appliance and proof of purchase. Any
defective part, in our judgement, will be repaired or replaced at the company's discretion. The dealer z
must obtain approval from an authorized company representative before any repairs are made.
WARRANTY LIMITATION
THIS LIMITED WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED AS TO QUALITY, MERCHANTABILITY, OR FITNESS FOR PARTICULAR
PURPOSE
The appliance is only warranted for the use as intended by the installation and operating instructions,
and local building codes, and the warranty will not cover damage due to accident, misuse, abuse,
alteration or improper installation.
This limited warranty is void unless the appliance is installed by a qualified installer, in accordance with
the instructions furnished with the appliance. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to the consumer.
/35
The remedy for damages as me result of any defects in this product wnich have been warranted herein
is limited to replacement of defective parts and does not include any incidental or consequential damages
or expenses sustained in connection with the product, including damage to property, the cost of removal,
reinstallation, or transportation of defective parts of the appliance. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to the consumer.
This warranty gives the consumer specific legal rights and he may also have other rights which vary
from state to state, or province to province. This warranty is limited to residential use of the product
only.
/3 6
w nrt/IAZ TM
MIURA/
SAMAR
PSOPMI
SALM Meullw
A.r w,O.
111.11' WA.
Mimeo N IrinallIlOt
LO VA
IA VA
INN
suss OM/M
17AN t Im
YIMulunme
N.IW /M
N.1W /11
IMO MAMMA
N.INIle/M
N.neswot
MINIMIA \tamemart
n.I IVs
11JN /a
IMNT IIM
romans/1w
,
. 11J11IIN /00
meetctlee 1n n
me OW 11
n.oMt /I•
AM
so%
II%
s,l MI /wan
V
PROMO
[ M - SAMIClKM
/I INS
ono
TAMS M onlnm
IYmIRAI AIM
Intel NI. IA
1111,* IQ. IA
R
I -HM/T•
1.401 /7
AlTAU01
1 -11Il l
1 -1111 le
Minimum Clearances to
Combustible Materials -
Measured to Maln lady
Installed ea an Insert IN masonry
and sere clearance lnpUces sr
with Otburn ten clearance tit:
A. SIdewell 10'/ 250 mm
le the Iles
I. Mantle W/ S1Omm
C. Ceiling 10' /1011 mm
Inslelled es a tr.estandlnl:
D. Sldawall r/ 200 mm
E. Inkwell 1 25 mm
E Carne 1'/ ES mm
le IahIhilea sad..M.g Mt1 SN eneapu111$
op Isms, loop loner In/ Wahl NmpIM1M ANL TIII
rum boar kNA eb W sole genaM sad mid le
Mulled N IMn to pnWww IN aleleltasomluO to col
suNUUM eta. On le blob melon den deihh4lnp Nll/na.
aldaly u/ lanllan avq.
Oa ad plus MINI M W arylad seal 1pp111M. D1 net Imp
lag1111 M No Admitl al ins stilhat We Ile minting, 01
All slam III mmllli m/1ehl nu ells gpluM.
Odgaglments minimum des
matdrltul combuslibla - Miurds
du Corps principal
tuadrl dine des Iofen eu Insu11/
nee la Ineas1 de IllaOemenl nil
d'Otburn:
A. Murlallrel
WO- / 250 mm
a It rine
or / S60 mm
/0'/101s mm
I. Man
C. Planed
Pale eneiin111:
0. Mue lallrat r / 200 mm
E. Mug mime t' / 15 mm
F. Cala i' / 2Smm
CAUTION: HOT WHILE IN OPERATION. DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY.
ATTENTION: CHAUD PENDANT LE FONCTIONNEMENT, NE TOUCHEZ PAS. TENIR ELOIONES LES ENFANTS, LE VETEMENTS ET LES MEUSLES.
LISTED PAN TYPE OAS FIRED VENTED ROOM HEATER
WI RADIATEUR \CIRCULATEUR VENTILE Set, NI,
frAe Tsd111nCAI000A1 .11M11, CORM 1 Cenllblbnso 1 no Ud.A.
Aaal10'1.11.tS 11111 An. Ansel Ue. IN11sni i Op PATatl / £501140
MHO: aa/Vida NO Q LP ❑ /RIVIT/ININSTANCE
DO NOT AMMOV' THIS Lien
(wed' 7056 1
WARNING: Improper inatallatlen, adluatment, service, or maintenance can cause In)ury
or property dames., Rifer Ho owners manual provided wills this appliance, For assistance
or sddltlonal information consuls qualified Installer s.Mo• agency or the gas supplier.
Nalale W palm Ip kAleW el Is nmpolanal de nmmanl .
reed NI M ltvollaM pialkn I rMdathUM el es
leadlwemaMpi enemppSM Is n11eNw, Pew allllullea
Ind N W sown.
IPSCIRC& I0Ml luenllautl till, a0Nl, IA
Pm mews de MIwUl, N nllallN reveled de Yell hits of
d1* Ike tsbll11 Swab nNnr IS elptdd,Msmse
DOWN MU de es is
IsmpinMn elnle M pals, IWWU elalple des ashnw, ul
'Mee eed sl im Molln.
Inert sellable ter nnpteeu wItles hearth
raised r (150 mm) ales nmenlinl
caminlble neer, and suitable ter masonry
Anplaeu wash an or (100 mm) hearth
enisnslen tea level naer. Refer Is manual lot
reload MIAA nielnmenls.
MM. famine aliening Is Mee and bntl al
can deerantl kit • 0 (0 mm) Is Hlandel% Ns
cambuellbles permitted slew snit ler a
distance s110115211 mm) abort fleet. Per use
with Need neallle pttlne connecter, A
cenventen 111, se welled by the Manulaclurer.
shall In vied U convert Ws nem healer le IM
alternele Nei. Syllable ter Inslalhtton In
b e/name when Installed with a Ihlnnesel. pea
Instruction manual.
Man It C IT:
01100* MANUTACIUAINO, OS Aralnlot AM, Videda. LC. VU 1G
Can in Item dent Nue eat
ndlM de (ISO mm) n•denat di
element einsbeilltle enlrumsnl.
Ceotlent per lis Wars 11 meson:mat
manly d'art pnleneemem d'Itre de tr
(111 mm) ear e1 psnch/r Ie nheee.
Meier as meant pas ibtenle by
stiffness Minn Net In en,
Olpaplmint min. mean In haet, SvI
he tiles et le anlln Is mulct i
I lppmld nil: Sp mm), Llanelli'
den ene anthem, A /0' (162$ mein
ninon i ptanthel. Ns tits mean
dent I'eo alai sea dsuun de I
Pen elllleslhn am le en nelson el It
I npanlints e. One lints de tenvetlea
Nmle par le falleenl deli Ilre rllllu
par past., don eemliAI111 1 Vann.
11.0011110
•
?Oa 'VII UN n. III MAIM
GAS & W./OD
w 1 I•NI•AIA
Installation Sketch
Include location of.... Furnace AWH Chimney A/C Unit Registers Current Equipment Key Valve
_ Combustion air grills _T-stat Meter Crawl access
Routes of..,. Gas Pipe Duct Work Electrical _ Condensate Linesets Waterpipes Relief
Notes
Pil P t^rnov
INCOMPLETE
LT R# I
Toy , .j --5 7kr
Sketch
Wntlig
APR 2 2002
Ks lau
L.DN' pig
RECEIVED
CITY OF TUKWILA
APR - 9 2002
PERMIT CENTER
Ma-048
Sub Total
5 'v I' r
Tax 8 ' %
$ ,a0 1�
Total Cash Price
$ 33/ o ;9r
Leas Cash Down Payment
O�
S /6 5 St
Amount Owing
S /46
(FlRST NAME, MIDDLE INITIAL, LAST NAME)
ruC l l5i/tPIe t('l fl r I I I I I 1 1 1 I 1 I
I
yo OF
l.NrtS
O REWRITE
D ORDER
Joe N
CASH PRICE
EQUIP
,IOe 11 1�1 ► I l
-
1 1 I—I 11 1-1 I l l
V413131 ISI 1 1 /15/il7�l'
1 1 1 1 1 1 1 1 1 1
1 1 1 1 1
CUSTOMER to
I
CI E/
IU l w 11 LA I 1 1 I I
AT
Go
ZIP
grl sc i 1 1I��
11.1.012±1E. HOME '-7 J BUSINESS
7
?-etc -) YV-- / 3 p
�+
1 l l
i
1
,I►v
44. 4-1 1 -I 1 1 f
(
x
DATE EAKEN�
s SS °2
i
O •TAx CODE
1 I '? 12 l c j
1 I► 1
I
I
1
1 I
1
I I 1 1 l 1 I 1 l
/22. ba
19 (/li✓ /� 1/tsTa (ethic v
S A I S � S D C I A
1 1 1 1
1
I
l
11
I
1 1 1 1 1
I
11 I I
3'i
MARKETI G REP,
/hi t
39 P`)
CITY
I 1 1 1
l
I
1
1 1
1
I I 1 I 1
STATE
I
ZIP
i t i l l
X
6 3
G3 loO
DESCRIPTION
ITEM NUMBER
WO TM wws.eruee ma•
yo OF
l.NrtS
L
OFF/CE USE ONLY
CASH PRICE
EQUIP
INSTALLS
-
1 1 I—I 11 1-1 I l l
I
���r/17�j�
f e.,0.7./.. (/
I I 1 -1 I I I -I I I I
t
I
.L
44. 4-1 1 -I 1 1 f
(
x
NV 7
9V /
,23 frk 1""°
to* I -Ilm4 I -1 1 I I
I
X
/ Z2
/22. ba
19 (/li✓ /� 1/tsTa (ethic v
ft4 t- toot7i -1 t I I
r ,?t
.. y3
Ay 3 1 ° "
fret s7 ;*,. /.; STo.e _ •`LA
GA4,459$ °11V 1 I
I
X
3'i
39 P`)
4,4-1 -i -1 i 1 I
r
x
SS
CS loo
a /or,J v 07 070 /"•
11
l ah-16 I I-I I I 1
X
6 3
G3 loO
.o,2, IA,/ 7 7-S74 T
1a31 -Ili 11 - I I l l
I
S 1-
S 3- i ce
/ lay
(,?r e c re
g
ria71 - I I I -I I I I
I
)C
l/2_
'/ 2- 1
r te I�i -I I I i--1 11 I
I
)C
2 $'
Ica
l ?1�
(t -I I I t -I I I I
I)C
9 i
9 I 1 00
4N31 -1 1 1 1 -t I I I
I
)c
al
■ ,-/ 1
A_ 40'1.- r 1
I I 1 -1 I I I -1 11 1
‹�
SO I C'
i
_,�
i
1 I J -I I I -I I I I
/�
�.1/Lli). 1 � (24t
!I/ ►l 1 -i e. ir•1 -1 / 1/ 11 If
XC
$
/9ff
I
/ V ( g-
SERVICE
ADDRESS
MAILING
ADDRESS
w«I
V /
A Slue 0.r+ Swears Co.
2000 THOIMDYI(E AVE W • SEATTLE, WA 911199
JK0 01.11 - 1 CONTRACT OF SALE
� OV ed SUBJECT TO APP ` EFCEPTANCE BY SELLER
App CITY
RECEIVE TUKWILA
APR P 200?
INSTRUCT1ONS —BLOCK PRINT
ITIS AGREED AND DECLARED THAT THE TERMS AND CONDITIONS SET
FORTH ON THE REVERSE HEREOF ARE PART OF THIS CONTRACT AND
BINDING UPON THE PARTIES HERETO.
NOTICE TO BUYER
Do riot sign this contract before you read it or if any spaces intended for the agreed terms
except as to unavailable Information, are blank. You are entitled to a copy of this contract
at the time you sign It.
You may cancel this contract, H It Is solicited In person and you sign It at a ace other
than the seller's business address shown on the contract, by sending of such
cancellation by certified mall return receipt requested to eel er at his address shown
on the contract, which notice shall be posted not later than midnight of the third day
(excludl Sunda and holiday.) following your signing this contract. If you choose
d ity sly a to the seller t the place of
,reoerYedbyyotlY tl treillie ittrsl)E' 'r
TERMS ON REVERIE SIDE: Refer to the reverse side for Information about the company's right to accelerate the maturity of the obligation and
other effects of nonpayment and default.
LATE CHARGES: A late charge equivalent to one and one-half percent (1-1/2%) of the current and all previous unpaid balances due, or fifty cents,
whichever Is greater, will be assessed If payment is not received within 15 days of the billing date.
RETURNED CHECKS: A $15 charge will be assessed on any check returned by the bank from which it is drawn, and customer agrees to pay this
charge.
PurehlNr Acknowledges Receipt of a C• •y 31 Oils Contract and Mat ha Is the
Owner Openly W , Iles In n S goods purchased undw Ms contract will
b. metalled. �1 Due
4
Sgn He:WY
ePurclurr')
Approved and
Accepted by
/e/
WASHIN ENERGY SERVICES COMPANY
OWED AGENT
D
CUSTOMER ACCOUNTING
FEB 2 8 2002
LESLIE
ETE
NTER
MOi- Qg
Magi '
Date
Name
Address
City
— County
Zip Code
Home Phone
Work Phone
Permit Information
City County
Is this Job a turn -key?
Yes No
Is this job a mobile home?
Yes No
Bid by: NWVVH
Manufacturer. OS����J
Existing Gas Service?
Yes No
Entry arrangements (Be specific!)
WESCO
Direct Vent I) feet
(feet)
"....v •1
LOGS = "-0-.. : " = •
: ; r' '
FIREPLACES _�. ..� ..:;
Existing Fireplace Type:
Proposed:
Gas Piping:
Masonry
Heatalator
Woo.
one • res - .
Zero Clearance
Gas Fireplace Insert
Direct Ven Gas Fireplace Insert
p
Zero stance has Fir ��pplIaacc��
a Standing Gas F
Gas Logs (cost to provide doors)
Other.
Length: / 2_
Diameter. �y
Fro here?
• ppliance (describe):
Proposed Equipment
Venting:
' Key Valve Location (describe):
Special Installation Instructions
Manufacturer. OS����J
B (feet)
W all —side
•
Direct Vent I) feet
(feet)
z F loor — side
A
Model: I- A 2 - 0 1
Flex Liner (feet)
/.vL,,.,--,
Revised 1011100
WESCO PSTALLATION INSTRUCTNS
RUSH SPECIAL HANDLING
Water heating " 7
Gas Piping:
Length: Diameter
From: Meter Appliance
Meter Location:
Pfeifle:
Fuel Relief
Cold Hot
Total piping
Proposed Application:
Gas to Gas AWH
Electric to Gas
Electric to Electric
Top vent
Direct vent
Power vent
Venting:
B C PVC Feet:
Roof Sidewall
Where?
Old Equipment:
Remove Leave
Leased
Combustion air. t *yes = ?no
.•ae, seti
Room size cu
BTU's
Door Wall_ Other
Stand
Expansion Tank
Current Equipment
Manufacturer.
Gal Height Width
Proposed Equipment:
Manufacturer. Model
Gal Height Width
Install in existing location?
Yes No if no then where?
Misc info:
* ** Please includ9 all payment data on Page 1 of
Installgtion Instructions * **
JOB #: 2 4 P 3' 6 1 S-
JNCOMP ETE
LTR#
* ** Sketch is required on all jobs, Uss Page 3 of
Installation Instructions * **
CITY OF TUKWILA
APR <-; Li1iJ�
PERMIT CENTER
Moog
..
i..,:o1,...klefiv,A
ELECTRICALIRERMIT,
k!Vvt;40;;;T:'
:44WESCOJOB
Cu • MER NAME:
...41 r/ cod. IL
PARCEL OR PROPERTY TAX ID #:
WO ? /o 0a s.
V
SALES REPRESENTATIVE :
A • •
ADDRESS:
L LA 3 k S • 1 (iAl -A
CUSTOMER PHONE:
el) C
-(
.4116
PERMIT COST:
CITY:
STATE:
Lo
ZIP:
C t5i155
C MUNICI
kJ
'\
ALITY:
VASOF WORK
(43 .00
'NUMBER
OF VOLTS
awsseespes
10.11PRININM
e===
Washington
EnenayServkes
A Blue Dot' Services Co.
DATE: C3/97
WASHINGTON ENERGY SERVICES PERMIT APPLICATION
ev.4
' EbtIA:NIC I A,,OLO . ,81441t
- .i•<: , :t.! , ;?.Y."
2i4q4WZOttrqaCENTRAL HEATING
MODEL:
FURNACE J WALL FURNACE
BOILER I MAKE:
ODEL:
INGPER
SIZE:
WATER HEAT PIPING FOOTAGE:
FURNACE G FOOT
N_FIREPLACE
NSERT
PIPIN
AGE: P
BOILER
PIP FO. E:
MAKE:
SIZE:
OTHER DESCRIPTION*
UMBI
•
MAKE:
SIZE:
MODEL:
FIREPLACE/STOVE! LOGS
A ,„-FIREPLACE I
INSERT I LOGS
FREE STANDING STOVE
MODEL:
•
A/C I MAKE:
MODEL:
GAS LOGS PIPING FOOTAGE:
RANGE PIPING FOOTAGE:
DRYER PIPING FOOTAGE:
OTHER PIPING FOOTAGE:
A KFL
:PRE VENTER
HOT
WATER:
COLD
WATER:
MAKE:LA —F___C)
SIZE:
2 C 3
.......negnsrviSfe‘releueeleSSele;
i..,:o1,...klefiv,A
ELECTRICALIRERMIT,
k!Vvt;40;;;T:'
. ";:?::.17 , 6 1-, :tarAego.PWAMEURNACE2i":4i,15k , wt , ';‘7. ,:: '
FlJRNACE
I NUMBER OF
I CIRCUITS:
NUMBER OF
AMPS:
'NUMBER
OF VOLTS
, :7-:A.::: , :::•4;4;13 , :irAIRCONDITIONING:; , .." ,, IY:.t.: , ii ,• •
AT
'NUMBER OF CIRCUITS:
NUMBER OF 'NUMBER
AMPS: IOF VOLTS
,!A'z =..,.;
HEATSTRIP
I NUMBER OF
I CIRCUITS:
NUMBER OF
AMPS:
'NUMBER
OF VOLTS
••• • .
HEATPUMP
I NUMBER OF
CIRCUITS:
NUMBER OF
AMPS:
!NUMBER
OF VOLTS
awsseespes
10.11PRININM
e===
Washington
EnenayServkes
A Blue Dot' Services Co.
DATE: C3/97
WASHINGTON ENERGY SERVICES PERMIT APPLICATION
ev.4
' EbtIA:NIC I A,,OLO . ,81441t
- .i•<: , :t.! , ;?.Y."
2i4q4WZOttrqaCENTRAL HEATING
MODEL:
FURNACE J WALL FURNACE
BOILER I MAKE:
ODEL:
INGPER
SIZE:
WATER HEAT PIPING FOOTAGE:
FURNACE G FOOT
N_FIREPLACE
NSERT
PIPIN
AGE: P
BOILER
PIP FO. E:
MAKE:
SIZE:
OTHER DESCRIPTION*
UMBI
•
MAKE:
SIZE:
MODEL:
FIREPLACE/STOVE! LOGS
A ,„-FIREPLACE I
INSERT I LOGS
FREE STANDING STOVE
MODEL:
•
A/C I MAKE:
MODEL:
GAS LOGS PIPING FOOTAGE:
RANGE PIPING FOOTAGE:
DRYER PIPING FOOTAGE:
OTHER PIPING FOOTAGE:
A KFL
:PRE VENTER
HOT
WATER:
COLD
WATER:
MAKE:LA —F___C)
SIZE:
2 C 3
.......negnsrviSfe‘releueeleSSele;
Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted
through the nail, fax, etc.
Date: l t
E Response to Incomplete Letter #
❑ Response to Correction Letter #
❑ Revision # after Permit is Issued
City of Tukwila
Department of Community Development - Permit Center
6300 Southcenter Blvd, Suite 100
Tukwila, WA 98188
(206)431-3670
Plan Check/Permit Number: MO2-068
Project Name: Shearer Residence
RECEIVED
CITY OF TUKWILA
APR 0 9 2002
PERMIT CENTER
Project Address: S 156 St
Contact Personl, Q nOU CR.__ enC Phone Number �--
�.J
Summary of Revision:
U},- -� (-c \ ∎n . s2.C). i S
(3 fir. tc krz Ia
1(■ DL) yen. yknov `T 03a SA-e. n. )(..?,c-
CA(\.\m \ o
C -\Acko c* a COQ L ` -Q
Con S
sco Lk c*\ .
Sheet Number(s):
"Cloud" or highlight all areas of revision including date of revision
JC6/1/
Received at the City of Tukwila Permit Center by:
❑ Entered in Sierra on q -"( - 0
04/05/02
April 5, 2002
Candice Gallagher
Washington Energy Services
2800 Thorndyke Ave W
Seattle, WA 98199
RE: Letter of Incomplete Application #1
Mechanical Permit Application Number MO2 -068
Shearer Residence
4433 S 156 St.
Dear Ms. Gallagher:
City of Tukwila
Steven M. Mullet, Mayor
Department of Community Development Steve Lancaster, Director
This letter is to inform you that your permit application received at the City of Tukwila Permit Center on
April 2, 2002, is determined to be incomplete. Before your permit application can begin the plan review
process the following items need to be addressed.
Building Division Ken Nelson, Sr. Plans Examiner
206/431 -3677
1. Please provide a letter from a certified chimney sweep or the installation instructions for a new
flue liner.
Please address the attached comments in an itemized format with applicable revised plans, specifications,
and /or other documentation. The City requires that two (2) complete sets of revised plans, specifications
and/or other documentation be resubmitted with the appropriate revision block.
In order to better expedite your resubmittal a `Revision Sheet' must accompany every resubmittal. I
have enclosed one for your convenience. Revisions must be made in person and will not be accepted
through the mail or by a messenger service.
If you have any questions, please contact me at the Permit Center at (206) 431 -3684.
Sincerely,
I<CrUt ,cr) C ..,d fh)
Kathryn A. Stetson
Permit Technician
encl
File: Permit File No. MO2 -068
6300 Southcenter Boulevard, Suite #100 • Tukwila, Washington 98188 • Phone: 206 - 431 -3670 • Fax: 206 - 431 -3665
State of Washington
County of Snohomish
I certify that this is a true and correct copy of this document.
Dated: rrb. 15-+4, 2c 2
My appointment expires October 9, 2003
Department of Labor & Industries
Contractor Registration Section
PO Box 44450
Olympia WA 98504-4450
1 To
REGISTRATION VERIFICATION
(360) 902 -5226
TEMPORARY (360) 902 -5228
om
&Fr�<< cJC LOCI
Registered name
rt)eSf+W G�.t ‘) cu` -6( Sens) ! S r_ 0
1 Registration number Registration expires
�;4sN 1.E / 0 .12— 14 .i
Contractor: Your Certificate of Registration will be sent from the Olympia office and
should be received within 2 to 3 weeks. Please keep this record until you receive your
Certificate of Registration. Re�ipte�iR:
C O J_ 01- G , _ Thank you
F625- 036-000 registration verification 12 -98
State of Washington
County of Snohomish
Dated: Apn_,ZOO 2
R2Cirda_ge5aLCe.S0Eerr
Title
My Appointment Expires on 1 o/f y°1/0 i
DEPARTMENT OF LABOR AND INDUSTRIES
REGISTERED AS PROVIDED BY LAW AS
CONST CONT GENERAL
REGIST. # EXP. DATE
CCO1 WASHIES990CW 02/16/2003
EFFECTIVE DATE 02/16/2001
WASHINGTON ENERGY SERVICES CO
2800 THORNDYKE AVE W
SEATTLE WA 98199 -2997
Di.tach And Di.play Certificate
I certify that this is a true and correct copy of said document as of this date.
CITY RECEIVED F
MAY - 3 2002
PERMIT CENTER
MOaOC?
ormation on
C • {:}.N 't8 K• +�} }S+�:k :#. F.•:• rr•. •..::x}tll ' ?(yi
.:: w }>: }:t` ??'.:'� ' }� ..0 t�9. . $ :• :x•:.k;2:.Y. ,•,: :.:R..:t?k•?�f+.: } :
it 2
JU
0
N 0
UJ
W
2
u. ?
( 12 a
Z �
O
Z
w
w
U
0-
W W
tL 0
WZ
0-
0 I-
Z