Loading...
HomeMy WebLinkAboutPermit M06-283 - ACT 3 CATERINGACT 3 CATERING 15665 NELSON PL M06 -283 Parcel No.: 0005800034 Address: Suite No: Owner: Name: CLOSE ROBERT J TRUSTEE Address: E 8262 HWY 106 , UNION WA City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206- 431 -3670 Fax: 206 -431 -3665 Web site: http: / /www.ci.tukwila.wa.us 15665 NELSON PL TUKW Tenant: Name: ACT 3 CATERING Address: 15665 NELSON PL , TUBWILA WA Contact Person: Name: LANCE CARLETON - CALL WHEN READY Address: Contractor: Name: PACIFIC STAINLESS PRODUCTS INC Address: 10100 SW ALLEN BLVD , BEAVERTON OR Contractor License No: PACIFSP117B7 DESCRIPTION OF WORK: CLASS I AND CLASS 11 HOOD SYSEM Value of Mechanical: $47,250.00 Type of Fire Protection: Furnace: <100K BTU 0 >100K BTU 0 Floor Furnace 0 Suspended/Wall/Floor Mounted Heater 0 Appliance Vent 0 Repair or Addition to Heat/Refrig /Cooling System.... 0 Air Handling Unit <10,000 CFM 0 >10,000 CFM 0 Evaporator Cooler 0 Ventilation Fan connected to single duct 6 Ventilation System 0 Hood and Duct 6 Incinerator: Domestic 0 Commercial/Industrial 0 MECHANICAL PERMIT Fees Collected: J;OUIPMENT TYPE AND OUANTITY * *continued on next page ** Permit Number: Issue Date: Permit Expires On: Phone: Phone: 206- 617 -9007 Phone: 360- 794 -7709 Expiration Date: 11/20/2008 Steven M. Mullet, Mayor Steve Lancaster, Director M06 -283 01/24/2007 07/23/2007 International Mechanical Code Edition: 2003 Boiler Compressor: 0-3 HP /100,000 BTU 0 3-15 HP /500,000 BTU 0 15-30 HP /1,000,000 BTU 0 30-80 HP/ 1,750,000 BTU 50+ HP /1,750,000 BTU 0 Fire Damper 0 Diffuser 0 Thermostat 0 Wood/Gas Stove 0 Water Heater 0 Emergency Generator 0 Other Mechanical Equipment 0 $707.53 doc: IMC -10 /06 M06 -283 Printed: 01 -24 -2007 Permit Center Authorized Signature I hereby certify that I have read an governing this work will be complie Print Name: doc: IMC -10 /06 � b City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206- 431 -3670 Fax: 206 -431 -3665 Web site: http: / /www.cttukwila.wa.us C. IM,c G of c Steven M. Mullet, Mayor Steve Lancaster, Director Permit Number: M06 -283 Issue Date: 01/24/2007 Permit Expires On: 07/23/2007 !♦ . I air ,A • Date: Di IZj to permit and know the same to be true and correct. All provisions of law and ordinances er specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating construction or the performance of work. I am a thorized to sign and obtain this mechanical permit. Signature: — C. INI t- Date: < zY /n? This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. M06 -283 Printed: 01 -24 -2007 Parcel No.: 0005800034 Address: Suite No: Tenant: 15665 NELSON PL TUB:W ACT 3 CATERING 1: ** *BUILDING DEPARTMENT CONDITIONS * ** City of Tukwila 4: Readily accessible access to roof mounted equipment is required. 10: ** *FIRE DEPARTMENT CONDITIONS * ** Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206431 -3670 Fax: 206 -431 -3665 Web site: http: / /www.ci.tukwila.wa.us PERMIT CONDITIONS Permit Number: M06 - 283 Status: ISSUED Applied Date: 12/14/2006 Issue Date: 01/24/2007 2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the Building Official. 3: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to start of any construction. These documents shall be maintained and made available until final inspection approval is granted. 5: Insulating materials, where exposed as installed in buildings of any type of construction, shall have a flame spread index of not more than 25 and a smoke development index of not more than 450. Where facings are installed in concealed spaces in buildings of Type III, W, or V construction, the flame spread and smoke - developed limitations do not apply to facings, that are installed behind and in substantial contact with the unexposed surface of the ceiling, wall or floor finish. 6: All construction shall be done in conformance with the approved plans and the requirements of the International Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code. 7: Manufacturers installation instructions shall be available on the job site at the time of inspection. 8: All electrical work shall be inspected and approved under a separate permit issued by the Washington State Department of Labor and Industries (206/248 - 6630). 9: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the Building Official from requiring the correction of errors in the construction documents and other data. 11: The attached set of building plans have been reviewed by the Fire Prevention Bureau and are acceptable with the following concerns: 12: Portable fire extinguishers shall be provided within a 30 -foot (9144 mm) travel distance of commercial -type cooking equipment. Cooking equipment involving vegetable or animal oils and fats shall be protected by a Class K rated portable extinguisher. (IFC 904.11.5) 13: Portable fire extinguishers, not housed in cabinets, shall be installed on the hangers or brackets supplied. Hangers or brackets shall be securely anchored to the mounting surface in accordance with the manufacturefs installation instructions. Portable fire extinguishers having a gross weight not exceeding 40 pounds (18 kg) shall be installed so that its top is not more than 5 feet (1524 mm) above the floor. Hand -held portable fire extinguishers having a gross weight exceeding 40 pounds (18 kg) shall be installed so that its top is not more than 3.5 feet (1067 nun) above the floor. The clearance between the floor and the bottom of the installed hand -held extinguishers shall not be less than 4 doe: Cond -10/06 M06 -283 Printed: 01 -24 -2007 inches (102 nun). (IFC 906.7 and IFC 906.9) `t.' City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 -431 -3670 Fax: 206 -431 -3665 Web site: httpillwww.ci.tukwila.wa.us 14: Fire extinguishers shall not be obstructed or obscured from view. In rooms or areas in which visual obstruction cannot be completely avoided, means shall be provided to indicate the locations of the extinguishers. (IFC 906.6) 18: A Type 1 hood shall be installed at or above all commercial cooking appliances and domestic cooking appliances used for commercial purposes that produce grease vapors. Each required commercial kitchen exhaust hood and duct system required by section 610 of the International Fire Code to have a Type 1 hood shall be protected with an approved automatic fire- extinguishing system installed in accordance with this code. (IFC 610.2, IFC 904.2.1 and IFC 904.11) 16: Local U.L. central station supervision is required. (City Ordinance #2051) 17: All new automatic fire- extinguishing systems and all modifications to existing automatic fire- extinguishing systems shall have fire department review and approval of drawings prior to installation or modification. 18: H.V.A.C. units rated at greater than 2,000 cfm require auto - shutdown devices. These devices shall be separately zoned in the alarm panel and local U.L. central station supervision is required. (City Ordinance #2051) 18: H.V.A.C. systems supplying air in excess of 2,000 cubic feet per minute to enclosed spaces within buildings shall be equipped with an automatic shutoff. Automatic shutoff shall be accomplished by interrupting the power source of the air- moving equipment upon detection of smoke in the main return-air duct served by such equipment. Smoke detectors shall be labeled by an approved agency for air-duct installation and shall be installed in accordance with the manufacturer's installation instructions. (IMC 606.1, 808.2.1) 20: Duct smoke detectors shall be capable of being reset from a single point near the alarm panel. (City Ordinance #2051) 21: Duct detectors shall send a supervisory signal only upon activation. (City Ordinance #2051) 22: Remote indicator lights are required on all above ceiling smoke detectors. (City Ordinance #2051) 23: All new fire alarm systems or modifications to existing systems shall have the written approval of The Tukwila Fire Prevention Bureau. No work shall commence until a fire department permit has been obtained. (City Ordinance #2051) (IFC 104.2) 24: An electrical permit from the Washington State Department of Labor and Industries is required for this project. 28: Contact The Tukwila Fire Prevention Bureau to witness all required inspections and tests. (City Ordinances #2050 and #2051) 26: Any overlooked hazardous condition and/or violation of the adopted Fire or Building Codes does not imply approval of such condition or violation. 27: These plans were reviewed by Inspector 811.1f you have any questions, please call Tukwila Fire Prevention Bureau at (206)575 -4407. * *continued on next page ** doc: Cond -10/06 MO6.283 Printed: 01 -24 -2007 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 -431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa. us I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and ordinances governing this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provision of any other work or local laws regulating construction or the performance of work. doc: Cond -10/06 M06 -283 Printed: 01 -24 -2007 Ll I Y Ur I UAWILA Community Developmen - apartment Permit Center 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 http://wwwatulavila.wa.us MECHANICAL PERMIT APPLICATION • Applications and plans must be complete in order to be accepted for plan review. Applications will not be accepted through the mail or by fax. **Please Print** King Co Assessor's Tax No.: 0065113 — 0011 Tenant Name: Site Address: / 5:44 /a/ SoaL) Pince, Suite Number: Floor: r s 4 New Tenant: 0... Yes 0 „No Property Owmn Name: e4 fi j Mailing Address: 2 79 5 PE 41 r sr fie Acre- 91 KT= City State Zip CONTACT PERSON -- who we de„ contact when your permit is ready to be Issued Name: Mite Day Telephone: 563 -6€1 / & Mailing Address: 7v/ e, /97/ er-e-ett-Ceereri the 74Pite City State Zi E-Mail Address: Fax Number:5173-6 4 cid CHANICAL CONTRACTOR INFORMATION Company Name: /7 C-- 57 S S Mailing Address: /0/00 S ct.) ytereetinA/s../ /5441,40e7b7 r City State Zip Contact Person: /ilt.t- zeo B E-Mail Address: Fax Number: al/Fri -d-- Contractor Registration Number: Expiration Date: Day Telephone: S otr-t e- , ARCHITECT:OF RECORD -= All plans must be wet stamped by Architect ot Accord Company Name. Masi /e 414- Pa Mailing Address: 1 It W 577R.J.e.. e, geethx/ ot Contact Person:/%1A 67 X4 Intel Day Telephone: # S 7o 4 o o E-Mail Address: Fax Number: ENGINEER OF RECORD -All plans must be wet stamped by Engineer ot Record Company Name: Mailing Address: City Contact Person: Day Telephone: E-Mail Address: Fax Number: QAApplicsilonsWorms-Applicanona On Line \ 3-2006 - Mechanical Permit Application.doc Revised: 44006 Ms State Zip Page I of 2 Unit Type: Qty • Unit Type:. Qty : Uait Type: Qty Boller/Compressor: . Qty Furnace<100K BTU Air Handling Unit> 10,000 CFM Fire Damper 0 -3 HP /100,000 BTU Fumace>IOOK BTU Evaporator Cooler Diffuser 3 -15 HP /500,000 BTU Floor Furnace Ventilation Fan Connected to Single Duct Thermostat 15 -30 HP /1,000,000 BTU Suspended/Wall/Floor Mounted Heater Ventilation System Wood/Gas Stove 30 -50 HP /1,750,000 BTU Appliance Vent Hood and Duct 4 j Water Heater 50+ HP /1,750,000 BM Repairbr Addition to Heat/Refrig/Cooling System Incinerator - Domestic ' Emergency Generator Air Handling Unit <10,000 CFM nn o� Incinerator- Comm/Ind Other Mechanical Equipment Valuation of Project (contractor's bid price): $ 49. T Scope of Work (please provide detailed information): (.2/1 . „19-Aid' Mod ,5� -c Use: Residential: Commercial: New .... ❑ Replacement .... ❑ New .... Replacement .... ❑ Fuel Type: Electric ❑ Gas ....0 Other: Indicate type of mechanical work being installed and the quantity below: Value of Construction - In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject to possible revision by the Permit Center to comply with current fee schedules. Expiration of Plan Review - Applications for which no permit is issued within 180 days following the date of application shall expire by limitation. The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be requested in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition). I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING OWNE OR AUTHORIZED AGENT: Signature: Moue Print Name: /1 / fib 7fa A-. Mailing Address: fi /1 5W ,41 t erti 61 vo Date Application Expires: I Date Application Accepted: ,^ , «IA Q Applicmiom\Forma- Applications On Lina33 006 - Mechanical Permit Applicatmn.doc Revised: 42006 bh Da te: iy/ /o0' Day Telephone: 51 3 ^ (v /_ tY lh - 7 70 o $- City State Zip Staff Initials: I Page 2 of 2 Parcel No.: 0005800034 Address: Suite No: Applicant: ACT 3 CATERING Receipt No.: R06.01978 Initials: JEM User ID: 1165 Payee: ACCOUNT ITEM LIST: Description doe: Recelot -06 15665 NELSON PL TURIN' TRANSACTION LIST: Type Method PACIFIC STAINLESS PRODUCTS, INC. Payment Check MECHANICAL - NONRES PLAN CHECK - NONRES City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 -431 -3670 Fax: 206 -431 -3665 Web site: http: / /www.ci.tukwila.wa.us De 088014 Account Code 000/322.100 000/345.830 RECEIPT Permit Number: Status: Applied Date: Issue Date: Payment Amount: Payment Date: Balance: Amount 707.53 Current Pmts 572.02 135.51 Total: $707.53 2368.12/19 9716 TOTAL $707.53 M06 -283 PENDING 12/14/2006 • • • 12/19/2006 08:59 AM $0.00 707.53 • • Printed: 12- 19-2006 Project: _S A 041 Type of Inspection: 1 , iI, 4 r Add SS / R ate �� ailed: Special I Date Wanted: 3 — a.m. /7-O7 Requester: Phone No: INSPECTION RECORD Retain a copy with permit INSPECTION NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 MG63 Approved per applicable codes. 0 Corrections required prior to approval. COMMENTS: a 72; /2174' ❑ $58.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to sechedule reinspection. Receipt No.: (Date: Project: A ,, f 3 Type of I spectiqn: li o,^ -.5 De.r-fy.i/ Address: / .14/,S /(/E /5o11/2 Date Called: Special Instructions: Date Wanted: ,Z - 2 V U - 4 (lit C M Requester: Phone No: INSPECTION NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431. INSPECTION RECORD Retain a copy with permit Ma G-2 3 P i (Approved per applicable codes. 0 Corrections required prior to approval. COMMENTS: 8.00 REINSPECTION FE1E REQUIRED. Prior to inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to sechedule reinspection. Receipt No.: Date: Project: 4 f 1 Type of Inspection: ,207, 4- ;6,.. Address: /5 S A/11 ,,j P/ Date Called: /^ Special Instructions: Date Wanted: 2 -7 2- 07 (a,� ' �r Requester: Phone No: INSPECTION RECORD Retain a copy with permit INSPECTION NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)4 1.3fj7 COMMENTS: I Ja Date: Z — ?2 7 8.00 REINSPECTIDN FEE R UIRED. Prior to inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to sechedule reinspection. eceipt No.: Date: Approved per applicable codes. Corrections required prior to approval. Proj f 3 Type of Inspection: A/ e . Address: / 5 GG S' 4 V,4 0 A/ r Date Called: Special Instructions: Date Wanted: 25'0 7 a.m� P .m. Requester: Phone No: COMMENTS: INSPECTION RECORD Retain a copy with permit INSPECTION NO. CITY OF TUKWILA BUILDING DIVISION A OG Z5 PE 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206 431.3. 0 0 Approved per applicable codes. 0 Corrections required prior to approval. a " 4 - / fr)., r I r "%"1- 7 Inspector: Date: / Z � $58.00 REINSPECTION FEE EQUIRED. Prior to Inspection, fee must be , paid at 6300 Southcenter Blvd., Suite 100. Call to sechedule reinspection. Receipt No.: Date: p COMMENTS: Type of Inspection: t` (JO !) I / )uc i Address: 15 t, , -; Suite #: ,‘i t-, soN Contact Person: ` L i( r A D S lc><_,u ' i^ zu_-t- Permits: 14- - G ,'A ,2- L 7 - />1: t7; °cc c.. / ^ /trill 6.; 81 f.i>(c ' tie 9I/ F! - !._ __ f r . ,' l! ! t __ 1 y y '� , Ili Or ti c. 1-7 L i'." X1 % t I //E Project: € ^,�-. , c q r L , N r� Type of Inspection: t` (JO !) I / )uc i Address: 15 t, , -; Suite #: ,‘i t-, soN Contact Person: ` L i( r A D S Special Instructions: Permits: Phone No.: Needs Shift Inspection: Sprinklers: Are Alarm: Hood & Duct: Monitor: Pre -Fire: Permits: Occupancy Type: INSPECTION NUMBER Approved per applicable codes. INSPECTION RECORD Retain a copy with permit Word /Inspection Record Form.Doc 1/13/06 PERMIT NUMBERS CITY OF TUKWILA FIRE DEPARTMENT 444 Andover Park East, Tukwila, Wa. 98188 206- 575 -4407 Corrections required prior to approval. Inspector: Date: /o9 Hrs.: v $80.00 REINSPECTION FEE REQUIRED. You will receive an invoice from phe City of Tukwila Finance Department. Call to schedule a reinspection. T.F.D. Form F.P. 113 "id if MMEl4GIAL KIT di:Y�°rii'w ` L+. ss+. allrnliu4d+ k .. . .: rt : =rvv.'.:v£awmhv�2..n::tiw.w.. "':'+ :.:: x. re. WfH: eth" Se. S::.' "`savw::1.Kwri,.'CTbiS:fl23as'Ji - PERFORMANCE VERIFICATION REPORT - Date: 3f5 /dl Project Name: /107 ethir InI Mechanical Permit Number: Street Address: /5665 Akt n Place Hood Type: / Dimension of duct opening into hood: / /k/(o ( Velocity of exhaust in duct: 9z g CFM of exhaust fan intake: /O/,90 CFM of MAU: / /yl5 Difference between EF & MAU: gl I Status of Capture & Containment test: 95% pasfed Name of Person performing the test: Mr. Deron V. Snyder Balancing Contractor: S.A.S. Balancing Services Inc. Balancing Contractor Bus. Ph. #: 1- 877 - 639 -3908 Balancing Contractor's CCB #: 56500 RECEIVED MAR 1 26; __BUILDING gT ACTIVITY NUMBER: M06 -283 DATE: 12 -14 -06 PROJECT NAME: ACT 3 CATERING SITE ADDRESS: 15665 NELSON PL X Original Plan Submittal Response to Incomplete Letter # Response to Correction Letter # Revision # After Permit Issued DEPARTMENTS: )14C 1-V4 Bui I ig Division us.l Public Works DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete 14 Comments: Documents/routing slip.doc 2 -28-02 Ins PERMIT COORD COPY ` PLAN REVIEW /ROUTING SLIP APPROVALS OR CORRECTIONS: Au i Fire 'Prevention Lai Structural ❑ Incomplete o DUE DATE: 1 Not Applicable ❑ Permit Center Use Only INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED: Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: TUES/THURS RO ING: Please Route Structural Review Required ❑ No further Review Required ❑ REVIEWER'S INITIALS: DATE: Planning Division Permit Coordinator • C C DUE DATE: 01 -16 -07 Approved ❑ Approved with Conditions Not Approved (attach comments) ❑ Notation: REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: License Information License PACIFSP117137 Licensee Name PACIFIC STAINLESS PRODUCTS INC Licensee Type CONSTRUCTION CONTRACTOR UBI 601134558 Ind. Ins. Account Id 81116800 Business Type CORPORATION Address 1 10100 SW ALLEN BLVD Address 2 City BEAVERTON County OUT OF STATE State OR Zip 97005 Phone 5036912511 Status ACTIVE Specialty I APPLIANCES/EQUIPMENT Specialty 2 UNUSED Effective Date 1/27/1989 Expiration Date 11/20/2008 Suspend Date Separation Date Parent Company Previous License Next License CURTIRE01402 Associated License Business Owner Information Name Role Effective Date Expiration Date CURTIS, DANIEL E 01/01/1980 KEMP, JEFF M 01/01/1980 CURTIS, MICHAEL R 01/01/1980 Look Up a Contractor, Electric; an or Plumber License Detail Page 1 of 3 Oar' Washington State Department of Labor and Industries General/Specialty Contractor A business registered as a construction contractor with L&I to perform construction work within the scope of its specialty. A General or Specialty construction Contractor must mamtain a surety bond or assignment of account and carry general liability insurance. Bond Information Bond Bond Company Name Bond Account Number Effective Date Expiration Date Cancel Date Impaired Date Bond Amount Received Date DEVELOPERS SURETY & Until b https://fortress.wa.gov/lni/bbip/printer.aspx?LicensePACIFSP 11 7B7 01/24/2007 Building Data Table: BLDG I BUILDING OCCUPANCY OUST. AREA: NEW ADDITION: TOTAL AREA: OLF OCCUPANT LOAD: I NO. EXITS REO'D NO. EXITS PROVIDED: . WWII REO D. WIDTH PROUDER: [::: OFFICE FOOD MANUFACTURING WEARHOUSE 8 F -1 F -1 5.322 SF 5,091 SF 5.587 SF 0 SF 0 SF 0 SF 5,322 SF 5.091 SF 6000 SF ' ?El 54 26 12 2 2 2 10' 5.2 6 TOTAL FLOOR AREA: 16.000 SF 16,000 SF 92 OCCUPANTS 2 EXITS 5 EXITS 22' 180' ` % • Code information & General Notes Fare roily owner: CHUCK DOREMUS DOREMUS FAMILY HOLDINGS, MC 279 SW 41ST STREET RENTON, WA 98055 Contractor: TO BE DETERMINED EXISTING USE: ZONE: NO. OF STORIES TYPE OF CONSTRUCTION: SPRINKLERS: OCCUPANCY GROUP: SITE AREA FLOOR AREA RATIO: PARKING REQ'D: PARKING PROVIDED: BASIC ALLOWABLE: Architect: HG KIMURA ARCHITECT 18012 W. LAKE DESIRE DRIVE SE RENTON, WA 98058 CONTACT: HOWARD G. KIMURA TELEPHONE: 425 - 766 -5000 General Notes: ACT 3 CATERING 15(5 NELSON PLACE :LIlWMLA, WA 95188 Building & Zoning Information: OFFICE FOR UNITED RENTALS TRENCH SAFETY EQUIPMENT TUKVYILA URBAN CENTER (TUC) ONE STORY 1116 NONE F -1 FOOD MANUFACTURING 39,774 SF OR 0.91 ACRES 16.000 SF / 39,774 = 40.22% OFFICE 3 STALLS /1000SF= 5.3X3 16 STALLS MANUFACTURING 1 STALL / 1000 SF - 5.587 X 1 at 6 STALLS WEARHOUSE 1 STALL/2000 SF = 5.587/2 = 2.79 X 1 = 3 STALLS 21 STALLS REVD 24 STALLS (INCLUDING ONE VAN - ACCESSIBLE) PER IBC TABLE 503; F -1, 1118 CONSTRUCTION = 12,000 SF BASIC ALLOWABLE AREA INCREASE DUE TO 3 SIDE YARDS > 30' = 6.720 SF + 12.000 SF = 18,720 ALLOWBLE JUSTIFICATION: Ao =At + [At'If /100) Ao = 12,000 of + [12.000sf'56/100] = 18.720 sf >16.000 SF, THEREFORE. OK. AND I WHEREAS [420/520-0.25) ('0 1 30/30, �% X1b0') /420' = 30' 1. ALL WORK SHALL BE N CONFORMANCE MTH ME 2003 INTERNATIONAL BUILDING CODE, MECHANICAL CODE AND FIRE CODE. 2003 UNIFORM PLUMBING CODE AID THE 2002 NATIONAL ELECTRICAL CODE AND APPLICABLE SEATTLE AMENDMENTS. 2. ALL BIDDERS SHALL MST THE SITE N ORDER TO FAM1UARIZE THEMSELVES WITH DOTTING CONDITIONS PRIOR TO SUBMITTING A BID. 3. CONTRACTOR SHALL VERIFY ALL DIl IEN9ONS SHOWN ON DIE DRAWINGS BEFORE COI/EKING WITH WORK. ANY OISCREPENCY StIALL BE BROUGHT TO THE ATTENTION OF THE ARCHITECT PRIOR TO STARTING CONSTRUCTION OF THE AREA CONCERNED. 4. UNLESS O1H011 NOTED. AU. PLAN DIMENSIONS SHALL BE TO CUM:RLNE. OR FACE OF STUD. OR FACE OF CONCRETE / O,N. 5. PROVIDE SUFFICIENT GROUNDS N NEW AND LOSING WALLS FOR SUPPORTING COUNTERS` CABINETS AND OTHER SIMILAR ITEMS AS REQUIRED. 6. FRL ALL HOLES AND VOIDS N FLOORS. WALLS ANL CEILINGS WHICH RESULT FROM INSTALLATION OF NEW WORK AND REMOVAL OF DOSING WORK INCUJOING MECHANICAL AND EL.ECTWCAL_ pATCHED AREAS SWILL MATCH THE MATERIALS, FINISH MD LEVEL OF ADJACENT SURFACES. OR SHALL BE N THE PROPER CONDITION TO RECEIVE NEW mists. AS SCHEDULED. 7. ALL MATERIALS INDICATED TO MATCH DOMING SHALL DO SO NTH RESPECT TO TYPE. PATTERN, TEXTURE SIZE. SHAPE, COLOR AND METrI00 OF INSTALLATION. N SO FAR AS PRACTICABLE. a MIT ABBREVIATIONS STALL BE CONSIDERED INDUSTRY STA DARES. CONTRACTOR IS RESPONSIBLE FOR VOreFICAIION WITH THE ARCHTITECT CF ANY ABBREVIATIONS FIST TO BE N QUESTION. 9. PREPARE THE IMPROVED AREAS TO RECEIVE THE OM ER S EQUIPMENT. CASEWORK FIXTURES AND DEVICES MERE LOCATED ON THE DRAWINGS OR DESCRIBED HERON. PREPARATION STU L N0.UOE ML NECESSARY ROUGH-R4 CONDUIT. PANG. OPENINGS` ETC. W RIFY ALL MMrUFACTIIRER'S SPECFIC REQUIENTS. 10. ALTERATIONS TO DOSING MIMICS S RESUJI.TNG FROM MECHANICAL OR ELECTRICAL WORK NOT SHOWN ON THE ARCHITECTURAL PLANS. SMALL BE REPAIRED NTH NEW MATERIAL AND MESH TO MATCH ADJRCOIT SURFACES. 11. A COPY OF TIE AMMO) FLAWS SHALL BE KEPT ON-91E AT ALL TIMES WHENEVER CONSTRUCDON IS IN PROGRESS. :2. TrE CONTRACTOR SMALL PAY Fe./ A' 3 NOM APPROPRATE AGENCY DEPARTMENTS FOR REQUIRED INSPECTION SERVICES OR TESTING, PFSOR TO PUTTING ANY MUTES N SOME. 13. CONTRACTOR IS 10 PIOC Z• row AND PAY ME APPROPIWAIE FEE'S AHD RETURN RECEIPT TO MINER FOR MEDIATE RERIBURSDADIT. • Legal Description: LEADER HENRY D C X46 BEG NXN N MG 1 S 158TH ST & ELY UGH ST HWY 20-M DI �. ALG N UGH TO WY WI ST HWY FRONTAGE RD Y UI TH NLY ALG W.Y LING 2.3 .37 FT 1H h 89 -00-00 170;1 TO 1POB 1H S 89 -00 -00 E 179 FT 10 FRONTAGE RD 111 NIT ALG W.Y UPI 230.34 FT TO PT 125.8 FT S OF N !N SD DC 1H N 89 -00-00 4l 170F'T 1H SLY TO 1POB Assessor's Parcel Number 000580 -0034 Non - Separated Use Justification This building is dassified as a" Ton- separated"use building per IBC 302.3.1. The uses in the building are as follows: a. Group Fl for food manufactusing b. Group B for the office at the balance ofthe building (previously established use) Maximum building area and height for both occupancy groups are: Occupancy Oonst. Type MIx. Ht. Basic Allowable (BA) BA with Increases Group B IIIB 4 stories, 55' 19,000 SF Not needed Group Fl IIIB 2 stogies, 55' 12,000 SF 18 SF Since non - separated uses do not require fire ndings between uses that are normally separated per table 30232, it is required that the balding be evaluated based upon the most restrictive coon type for height and area per IBC 3023.1. In this case, Group F1, type BIB only allows 12,000 sf of basic allowable area. The allowable increases due to adeyards (IBC 506) allows us to have a 18,720 sf budding. See calculafions on sheet Al under budding CIE zoning information. Since the Act 3 Catering space is allowed to have 18,720 sf under the most reattidive use (F-1, IIIB Cast) and the actual area ofthis building is only 16,000 SF, we have met the arealimitaliorhs sad heighht restdc6oes ofthe mod rabidive use and consbuc6on type. Additionally, the most reStridive height allowed for type IIIB corotruc6oe, Group F-1 Occupancy is 2 stories, SS' and the actual building is one -stay, approximately 15'-3" height. Therefore, this building an be classified as a lion-separated" use type building per IBC 3023.1. • EXISTING 16,000 SF, 1 -STORY CONCRETE TILT - -UP STRUCTURE, TYPE II1B CONSTRUCTION, 15' -3" HT. 901 INOICA1NC NO PAWING t • W ACCESSIBLE ME SPACE o MID. 5' ABOVE FINN. GRADE ' TO BOT. OF SIGN. MOUNT HANDICAP PARING SIGN MN. 5' ABOVE FIN. GRADE TO DOT. OF SIGN I 1 -- 1 i 1 COMING VERIES OWS/LOGO DESIGN - - Moto. tg5 ■••■••111101=0 • - 170' - - SEAT PERMIT E•:WIRED FOR O PecharkaI Eiectrkal O Plumbing Ges Qty of Tukwila BUILDING DIVISION N 8900 W M M.I.M- - - ea. - MOWN DE114EES CATERING EXIST. PARKING TO REMAIN NEW HANDICAP RAMP & STALL BOST. PAVED PARKING LOT REPAINT PARTING STALL U1ES NINTH 4' VIDE WE LINES 170' - SITE PLAN Is = 20'-O' 5kbjcc+ 40 I) 2.) � ii *9 14i rv� -fee. - {dui- �ic�;a.� ��,tc. 5trt.r k;iJl flkU ar1.13 Incitriseliavt . 51154414 hat . tuAu t)isic., 9' - pal F- LUST 9' Dee ^.I `'' PARKA! 3 TO 9' 9' 9' COPY Permit No. flare livlew amoral Is subject to ems and omissions. the violation cf of construction documents does not any aoabed code cr ordklarhm. Reoee oI approved Fief CON Znd concEtiorn b edmavIedgett City of Tukwila eWLDING DMSION BtaaSiatiS t o clasnges shall be made to the scope C t without prior approve ct e T':xb Building rey:.:.�e a roc:: :._N I zna n.-y taide additional Flan ter.e.: fps. 9 NORTH 1 1� 1 MY ENTRY TO OFFICES I i I I MATCH wDTN OF ENTRY RECESS - SHE VQOFY EXACT 111. REMOVE EXIST. CONCRETE WALK, INSTALL NEW 5' HIDE 4' THICK GONCREIE SLAB OVER COMPACTED SUB -BASE NI1H I4 REBAR AT 24' OC EA. WAY. DPAN. JIS AT 15' O0,, CONTROL JIS AT S OC. YAXIWM CROSS SLOPE ON SIDEWALK TO BE 2% YAWL 6' RISE MAIMIUM IN 6' OF RUN AT RAMP RE-VIEWED P N CODE CE p n nnrl%/ci3 JAN 2 41 2001 City Of Tukwila BUILDING DIVISION RECE;' /Ej CITYCJF Et 14 2006 PERviicENTER DATE SENT mole 120LT1I MIDST REVISIONS Act 3 - Catering 15665 Nelson Place Tukwila, WA 98188 HG KIMURA ARCHITECT Amainrcrum & FAC1un. PLANNING s 1n. $000 Fax 42S271 MAhL ve012w.1 sesuresERSE RaiiaaI►AMOSS 51 REGISTERED ARCHITECT OMURA at smosurkin DATE: 7 -6 -c Joe NC.06- Al E X I--I AU S T FANS (COMMERCIAL KITCHEN EXH. FAN UNITS) /ITEM /// QTY. // /MA IRER MODEL/ / / /// HP // VO / TS // /P // c / SAP RPti wt -L�. FAN BASE EX 1 1 LOREN COOK VCR I80v 65 3/4 115 1 2600 I 1041 143 30' x30' EX 2 1 LOREN COOK VCR I95v 615 3/4 115 1 3000 .815 939 153 30' x30' Ex 3 1 LOREN COOK VCR 195v 6B 3/4 115 1 2860 .15 880 153 30' x30' EX 4 I LOREN COOK VCR 195v 6B 3/4 115 1 2860 .15 880 153 24' x24' EX 5 1 LOREN COOK ACE-15 I00C 25 1/6 115 I 613 25 1301 41 18' x 18' EX 6 1 LOREN COOK ACE -B I00C 28 1/6 115 I 525 25 1181 41 IS' x 18' EX1 i 1 FURTHER ADDITIONAL EXHAUST FAN REQUIRED 10' EXH. COLLAR a 1200 CM N/A SUF'1L. r A I IR FANS (EAvF COOLER UNITS) BLOLER OPENING ///////4 .DUT OPENING °u / C/i/ / //l //// / ITEM /// . / Q TY. // / / / / / / // // MAGTURE ////// R //// ///// MODEL / / /// .// HP // ,/ //// VOLTS / / / / //, PH_ / // , //� CFM / /// /,',//// SAP l /♦ ,� RPM /i/ /// WT. -LB. / i / /, MU 1 I PHOENIX DAN - 8801 2 208 3 5120 1.0 538 P 416 21 3 4' x 21 3 4' MU 2 1 PHOENIX DAN - 8801 2 208 3 6050 1.0 526 qPer= 416 21 3 4' x 21 3 4' DUCT FURNACE (DUCT NEATER UNITS) / / / / / //f ///////7/////7////_/////7///, INPUT INPUT - BTU / /7//// 315 ,000 / / / /,y O UT - PUT / / / /// 216,000 / / / /_/ ,, ,// /// 321 / / / / / / //, OPENING / / / / / / /// 18' x 40' I /// /IT EM / /1//4/ QTY / / / / / /// ANUF / / / /� / / / / /// MODE / /// / / /// / VO L TS ! / /// OF 1 1 REZOR - GAS _ CRG 350 IISv controls DF 2 1 REZOR - GAS (RCS 350 II5v controls 315 ,000 216,000 321 10' x 40' E X 1-4 A U S T 1-1 o o D 5 (EXH_ VENTILATION UNITS) HOOD SIZE - //// /ITEM /// / QTY. // / / / / / / // /l MANUFACTURER ,,,,,//// 7/7/ MODEL/ /i /// /////%/ //// SYST .+ 1 TYPE / � LTH /� / / / / /// /�/// // W //i� ////////// )57/ EXH f T / //z/ /��,,,,,, ' • Y , , � Cq , g ��` Vi-i I i VENT -MATIC CDW ETL- LISTED TYPE 1 i 1'-0' 48'. 3' 24' 14'x14' UP N/A 1/1-I 2 1 VENT -MATIC CDW ETL- LISTED TYPE 1 I0'-0' 48'. 3' 24' 14'x15' UP N/A v14 3 1 VENT -MATIC CDW ETL- LISTED TYPE 1 11' -0' 48'♦ 3' 24' 14'x!6' UP N/A VI" 14 1 vENT -MATIC CDW ETL- LISTED TYPE 1 11' -0' 48'. 3' 20' 14'x16' UP N/A VH 5 I PAP. CUSTOM 'C' I vAPOR STYLE 1400D - TYPE 2 42' 42' 20' 8' round UP N/A 1/N 6 ' 1 RE -USE EXITS' TNG OUNER EXH. HOOD I CONDENSATE 6' 42' i8' j 8' round UP N/A VI 1 1 'LUCKS' RACKOvEN FURTIER ADDITIC•AL BY CW4ER REQUIRED 1 0' EXH!. COLLAR none iii1 f mo ft o i a g o 3•'.3 u aG H 0 - i , Q. V V t Pacific Stainless 0 :NOISIA38 SCALE: TOTED CHECKED: D. S. JOB NO: 0044642 DRAWN BY: DfiRi4 90 /1.0 /Zl :31bd N in 0 TO&T TYPE I HOOD NOTES - L HOOD TO BE 10 GA S/S, ALL - MELDED CONSTRUCTION* ALL JOINTS AND SEAMS TO BE GROUND TOOTH. 2. DUCTS TO BE 16 GA. GALVANIZED OR 18 GA S/S ALL - WELDED, GREASE - TIGHT CONSTRUCTION FOR EXHAUST. 3.FIRE PADS TO BE 22 GA SHEETMETAL ON N' MINERAL WOOL BAITS REINFORCED WITH WIRE MESH. 4. TYPE I - EXHAUST DUCT SHAFT TO BE 1- HOUR FIRE RATED CONSTRUCTION (TO BE VERIFIED BY THE LOCAL BUILDND AUTHORITY) 5. TIE GENERAL CONTRACTOR SHALL PROVIDE AND INSTALL ALL PENETRATIONS, SHAFTS, RAN SHIELDS AND SEAL EATMER TIGHT 6. AN APPROVED. AUTOMATICALLY OPERATED, FIXED PIPE FIRE SUPPRESSION SYSTEM SHALL BE INSTALLED OvER THE COOKING AREA PROVIDED UNDER SEPARATE PERMIT BY A LIC. CONTRACTOR. 1. EXHAUST DUCTS SHALL SLOPE TOWARD HOOD 114' PER 12 OF LINEAL LENGTH AND ACCESSIBLE CLEANOUTS SHALL BE PROVIDED AT ALL 90? ELBOWS AND 10'- 0' MN. SPACING S TYPE 1 EXHAUST HOODS AND DUCTS TO NAVE A MNMIl1 CLEARANCE FROM COMBUSTIBLE SURFACES OF At LEAST W. 9. TYPE I EXHAUST OUTLETS TO BE MINIMUM OF 40' ABOVE TOP OF ROOF SURFACE AND 10' -0' FROM ANY BUILDING AIR INTAKE 10. THE EXHAUST AND MAKEUP AIR SYSTEMS SHALL BE CONNECTED BY AN ELECTRICAL INTERLOCKING SWITCH ALL ELECTRICAL (BY OTHERS) ( REFERENCE TO ELECTRICAL DRAWINGS ) U. EXHAUST HOOD GREASE FILTERS AND LIGHT FIXTURES TO BE IL LISTED. 12. CONSTRUCTION OF EXHAUST SYSTEMS HOODS AND DUCTS TO CONFORIM 10 NFPA' 0 96 . D. THE ELECTRICAL CONTRACTOR SHALL MAKE ALL APPLICABLE CONJECTIONS FOR PROPER OPERATION OF ALL SYSTEMS. 14. THE GENERAL CONTRACTOR SHALL VERFY ALL DIMENSIONS BEFORE CONSTRUCTION OF PENETRATIONS AND COORDINATE CRITICAL EXHAUST SYSTEM REQUIREMENTS WITH ( PST) B. THE ELECTRICAL CONTRACTOR SHALL LOCATE ALL ELECTRICAL COMEGTIONNS FOR EACH PAN MOTOR AT EACH FAN LOCATION. 16. THE ELECTRICAL CONTRACTOR SHALL Y ALL THERMAL DISCONNECTS AND MAG STARTERS 11. THE EXHAUST AND MAKE UP AIR SYSTEM IS COVERED BY A ONE YEAR PARTS AND LABOR WARRANTY FROM THE DATE CF EQUIPMENT START UP, PROVIDED A QUALFIED SERVICE COMPANY IS PERFORMING REGULAR FILTER CLEANING AND MAINTENANCE. THIS WARRANTY IS VOID F NO SERVICE HAS BEEN PERI=ORMED AFTER NINETY (90) DAYS FROM THE EQUIP. START UP DATE. TYPE 2 HOOD NOTES - I. HOOD TO BE 1B GA 5/S, ALL - WELDED CONSTRUCTION 10T14 ALL JOINTS AND SEAMS t0 BE GROUND T14. 2. DUCTING TO BE 24 GA. GALVANIZED NON - WELDED DUCTWORK 3. THE GENERAL CONTRACTOR SHALL PROVIDE AND INSTALL ALL PENETRATIONS, SHAFTS. RAN SHIELDS AND SEAL WEATHER TIGHT. 4. EXHAUST DUCTS SHALL SLOPE TOWARD HOOD 114' PER 12' OF LINEAL LENGTH. 5. THE EXHAUST AND MAKEUP AIR SYSTEMS SHALL BE CONNECTED BY AN ELECTRICAL INTERLOCKING SWTCHL (ALL ELECTRICAL BY ELECTRICAL CONTRACTOR - REFER TO ELECTRICAL DRAWINGS). EXHAUST 14000 AND LIGHT FIXTURES TO BE UL LISTED. 1. CONSTRICTION OF EXHAUST SYSTEMS HOODS AND DUCTS TO CONFORM TO 'INC' CODE. 8 THE ELECTRICAL CONTRACTOR SHALL MAKE ALL APPLICABLE CONNECTIONS FOR PROPER OPERATION OF ALL SYSTEMS. 9. THE GENERAL CONTRACTOR SHALL VERIFY ALL DIMENSIONS BEFORE CONSTRUCTION OF PENETRATIONS AND COORDINATE CRITICAL EXHIAUST SYSTEM REQUIREMENTS WITH ( THE ELECTRICAL CONTRACTOR SHALL LOCATE ALL ELECTRICAL CONNECTIONS FOR EACH FAN MOTOR AT EACH MN LOCATION. II. THE ELECTRICAL CONTRACTOR SHALL SUPPLY ALL THERMAL DISCONNECTS AND MAG STARTERS. 12. THE EXHAUST AND MAKE UP AIR SYSTEM IS COVERED BY A ONE YEAR PARTS AND LABOR WARRANTY FROM THE PATE CF EQUIPMENT START UP, PROVIDED A QUALIFIED SERVICE COMPANY IS PERFOt - tI4G REGULAR MAINTENANCE THIS WARRANTY IS VOID IF 140 SERVICE HAS BEEN PERFORMED AFTER NINETY (90) DAYS FROM THE EQUIP. START UP DATE. NOTE: EXHAUST DUCT REQUIRED (GREASE) CLEANOUT ACCESS PANEL -DOOR TO BE PROVIDED AT THE PROPER LOCATIONS 3M FIRE BARRIER DUCT WRAP - 15A RATED FIRBIASTER'' 1Fr. BLANKET NON COMBUSTIBLE MATERIAL 1 - LAYER of IV=' thick -INSULATION_ INSTALLATION BY PSP • • • nvrLw 3M FASTURAP MATERIAL TO INSTALLED STALLED PER FIRB1ASTER CFICATIONS 6/5 BANDS 014 V` 0O. ONE ROM RATED . RASTER MGT cumizET 11 LAYER) OF AV TAR= - Ov_AP ALL ACM" Am OF-A115 TO EE !Fy+D RETR FM�IASTER TAPE DETAIL OF FIREMASTER DBt- Ntn ALL THREAD AT TOP AND BOTTOM S/8' ALL THREAD ROD RF . LOCATED AT COMERS row AND MED row GN HOOD 1r -m" AND ABOVE 18' CLASS I� I L LISTED HOOD 6/S 14 GA. HANGER MELDED TO HOOD IN FIELD BEAM CLAP TO STEEL TRUSS SUPPORT R �TYPICAI. OOF TRUSS OR CEILING BEAM n J 25u6' STEEL BALL BACKING II WALL BENW ESL HOOD I SECURE WALL FRAME CMG B N FALL w NO. le SRI. FILL. 6,13 ecI 5•24 •. 2 ROBS DEEP � 16 GA. SAS W1LL FRAME MELDED TO BACK CF HOOD CC LINE TYPICAL EXH. HOOD HANGER DETAIL N. T.S. SCALE NOTE NOTE LEGEND FD. - FIRE RATED DAMPER CA. - CLEAN OUT DOOR (EXH. DUCT) MIA - SUPPLY AIR 4- (0 -TYP. FLEX CONNECTER RN •••••■ - TYP. METAL DUCT N FLR- FLOOR AREA GG: - GENERAL CONTRACTOR I.. - SUPPLY AIR DIFFUSER (ceiling) - SUPPLY AIR DUCT - EXHAUST DUCT SQUARE - EXHAUST DUCT ROUND - AIR FLOW DIRECTION moo - MANUAL VOLU E DAMPER EXISTING DUCT EXH. RAN EQUIPMENT SCHEDULE ic TO KITCHEN AREA 'MUA' SULLY TEMP. AIR TOTAL= GEM 11,993 • NOTE: MAINTAIN A CLEARANCE FROM COMBUSTIBLE MATERIALS OF NOT LESS THEN IS' INCHES FROM THE HOOD TNIS MAY BE REDUCED TO NOT LESS THEN 3' INCHES PROVIDED THE COMBUSTIBLE MATERIAL IS PROTECTED WITH ONE HOUR RATED MATERIAL (1MC / OMSC sec. 501.9) NOTE: A WET CHEMICAL EXTINGUISHING SYSTEM WILL BE PROVIDED FOR ALL CLASS I HOODS AND WILL C�Y THE UMC SEC. 5 4.1, FIRE DEPARTMENT AND FIELD INSPECTION BY THE LOCAL JURISDICTION FIRE EXTINGUISHING SYSTEM CONTRACTOR NULL PROVIDED DETAILED DRAWINGS AND SPECIFICATION TO THE LOCAL JURISDICTION FOR REVIEW NOTE: GENERAL CONTRACTOR IS RESPONSIBLE FOR RATED DUCT SHAFT CONSTRICTION W/ NON COMBUSTIBLE MATERIAL FIRE RATED ENCLOSURE TO BE CONSTRICTION TO LOCAL B UILDING CODE NOTE: 140005 LESS THEN 12' INCHES FROM WALLS AND CEILINGS SHALL BE FLASHED SOLIDLY WITH MATERIALS OF THICKNESS SPECIFIED IN THE RMC/i01ISC s 5019 OR MATERIALS CONFORMING TO ONE HOUR RESISTIVE CONSTRICTIONS (UMC SEC. 508.2) • GENERAL NOTES THESE ARE GENERAL NOTES BASED ON TYPICAL CONSTRICTION. IN ALL CASES LOCAL CODES HAVE PRECEDENT OVER THESE NOTES AND IT IS THE RESPONSIBILITY OF THE INDIVIDUAL CONTRACTORS TO FOLLOW SAID CODES DIMENSIONS SHOWN ARE FROM FACE CF FINISHED WALL OR FLOOR TO CENTERLINE OF ROUGH -IN AND CENTERLINE OF ROUGH-IN TO CENTERLINE OF ROUGH -N, UNLESS OTHERWISE SPECIFIED AT DIMENSION. MECHANICAL NOTES 0 FANS MUST BE LOCATED 10' -' MINIMUM FROM ADJACENT BUILDINGS AND PROPERTY LINES AIR INTAKE FROM MAKE -UP AIR WIT AND H.VAC. SYSTEM SHALL BE LOCATED 10' -0' MINIMUM FROM EXHAUST FAN OUTLETS. FINAL AIR BALANCING OF HOOD SYSTEM TO BE COMPLETED BY APPROVED CONTRACTOR AFTER ALL HOODS, MAKE -UP AIR AND BUILDING AIR UNITS ARE INSTALLED. ELECTRICAL NOTES ELECTRICAL CONTRACTOR SHALL MAKE ALL ROUGH -NS AND FINAL CONNECTIONS N E WITH ALL LOCAL CODES ELECTRICAL CONTRACTOR SHALL SUPPLY ALL DISCOMECTS, INTERLOCKS, AND MAG STARTE REQUIRED ON ALL EQUIPMENT AS REQUIRED BY LOCAL CODES OR AS SPECFIED. KITCHEN CONTRACTOR SHALL SUPPLY TCHEN EQUIPMENT CONTRACTOR WITH EN WRITT VERIFICATION FROM POUER SUPPLY COMPANY OF VOLTAGE AND PHASE OF POWER AVAILABLE TO THE BUILDING. ELECTRICIAN SHALL VERIFY WITH P.S.P. ALL VOLTAGES, AMP LOADS, AND OTHER SPECIFICATIONS ON ALL EXISTING / DUER SUPPLIED EQUIPMENT TO EE USED. �; 14 ?:,: -: • 0 m X iL 1 4 W z O E CO 0 LO v 1 7 (360) 7c14-770q G17005 Tel. DRAWING NO: TTO&eil a 1 TITLE: 1 DRAWN BY: n1zi-1 CHECKED: D. S. REVISION: . >, a C 1 i c Sta he informatioon� disclosed WO and Slami and except for rights expressly granted to the cus cu tomer less Products, Inc. reserves all use "sale, proprietary, i design, reproduction ri ghts thereto ACT CATERING ✓ NE J.. v4�I'�. SCE TU W f !� WA 981 SS • DATE: 12/01/06 JOB NO: 00446 SCALE: NOTED C P N I T D O M U C I F E E D OR1100 , • • • • • a 1). r z m CPN 0 0 I m z m 0 1> n � c� Vic' 2 -.n ' r • '„ 01 "" :� r'.` r r, .' : . i d '1 :t: I `,Fr • • ..WWW..WWW.. • ./ i. mimes .mem ammm...rs.._.. ....rrr. =....r r,r.■.rr,r. tss 9$ r- ;Pi � 1 Cl Tit Z A E f11 $01 r" J i 1 1 I SMARM e L--= 1 0000. 2D I/2 I lg 1 I ! 1 .•0000:.•. r A N ..._ ._...rr._..y_..N Z • IMMIIMMIB Pacific Stainless Products, Inc. 10100 /SW Allen Blvd. - Beaverton, Oregon 87005 Tel. (503) 641 -7060 - Fax. (503) 646 -2348 * * ** MONROE, ILIA. Tel. (360) 714 -770q - Fax. (360) 7q4 -8182 DRAWING NO: TTO&e 3 O F / 1 TITLE: PLACE ee DRAWN BY nIRi-1 CHECKED: D.S. REVISION: 0 is ea . B C I i C - information disclosed was and n the property o f�dc Snle Products, and except for rights expressly Pocif c i , D i ns less Products, Inc. reserves all potent, proprietors, design, ,reproduction r g there - • ACT m CATERING 1 fl 156•6 . NELSON TI UIKW I,,.1„ WA. °J e 1 DATE: 12/01/06 JOB NO: 00446 42 SCALE: MOTE D St c p Q ®� M CC G 0 b a 1 11, a — J is • • r r 1> rn E 9 41 3 rn C) i0 0 0 rn .....- ••••• ......•.•••••••••••••••••••••••••••.•••••••••••••••••••••••••••••• 1 t P 1,x Si qm ••••■••. aim= .• p rpr. v. . i • ..Y`I. J •• .•� ••r•. I . — .T ,r. ........_ • I ...M. _ ...... • •••••:19 • ••■•••• • ••• -..••• » .._...* • _.rte.-_ ». o. :•.••.•: :; r oars- 1 . ._.......- - M•.••... ELEVATION VIEW or Roca MEOW. TOP SECTION A .r ■••• " s g Ct O C- r o • • j : : ton 4. mama • -- --- ammil r • • ij \ \ . i ! iI 0 1 — nh — ELEVATION VIEW or I OOP MECH. TOP SECTION AREA I I..... .• CT RIPla Oc 11 �I '1 i f II it T • 1. Pacific Stainless Products, Inc. 10100 /SW Allen Blvd. - Beaverton, Oregon 87005 Tel. (503) 641 --7060 - Fax. (503) 646 -2348 * * ** MONROE, A. Tel. (360) 7q4 -770q - Fax. (360) 7q4 -8182 t • • • NOTE: ALL DI:'iENSICNS ARE TO BE FIELD VERIFIED PRIOR TO FAB CF S/S EQUIP. ITEMS BY Pacific Stainless Products I GALVANIZED SUPPLY 14'dla. AIR DUCT --- DROPS LOCATED IN JOIST SPACE ABOVE HOOD AREA SNAP -LOCK DUCT TYPE SUSPENDED 3 'T' BAR CEILING LINE FLOOR LINE ROOF LINE E 3/4• = r -0• SCALE 10' -MIN DIS TO ADJACENT AIR - INLET$ IS= MIN. DIS F4 24 ROOF JOISTS oss------ DUCT 14'+ FLEX MAKE -UP AIR 7 ,---r SUPPLY FLEX (TEMP? AIR) SUPPLY AIR DIFFUSER TO KITCHEN AREA CEILING DIFFUSERS *REQUIRING (MVO) MANUALLY CONTROL_ VOLUME DAMPER AT DUCT TAKE-OFF TWO EA - 48' x i0'- 0 CANOPY STYLE TYPE ETL LISTED EXI -IAUST HOOD SYSTEM / VENT -MATIC MODEL 1 CDW 5/5 ALL WELDED GREASE AND WATER TIGHT CONSTRUCTION GREASE TERMINATOR 1W REMOVABLE CANISTER TYPE 1E1cxoE__ g/5 P ANELS KITCHEN COOK LINE EQUIP. 6/5 mall flashing from bottom of hood to floor - Ft 22 1r2 x 30 14 x END SECTION E XI- _ I —#OOD VIEW - �/�-# 1 x/4-12 E X 1 MODEL VCR 180V 613 CFM 2600 E x 2 MODEL VCR 195V 66 CFM 3000 UP -BLAST = UL LISTED LOREN COOK EXHAUST FANS HINGED FAN SUB BASE ASSEMBLY VENTED ROOF JACK by PSP. U 24 24 -11I14. DI5 40'- MIN. DM. lbga. GALV. DUCTWORK TO BE ALL WELDED CONSTRICTION LIQUID t AIR TIGHT CONTINUOUS by PSP RATED FIREMASTER' tr. BLANKET NON COMBUSTIBLE MATERIAL 111 I LAYERS of 1 RATED INSULATION INSTALLATION BY PSP 3' AIR SPACE W/ alraLL FRAME TYP. NOT FOODS KITCHEN f R REV1ON P GE COOS O (all otiTutcvliiStON 6WILDIIG DNt 14 ? 7 3 lo2fricAtEs f I X d it [1 1 DRAWING NO: TITLE: ACT J.L1 156065 TUKUJ mm C O T E I N SON i t � �l { DRAWN BY: 1-1 D� CHECKED: D. S. REVISION: Pamir ' St inform disclosed by and is the property of Pacific Stainless Products, Inc. nd ecept for rghts custom r � er, Pacific to the acific Stain- less Products, Inc. reserves all patent, proprietary, design, thereto rproduction • ohtst OF I PL AC • DATE: 12/01/06 JOB NO: 0044642 SCALE: NOTED I L A, LUA, 98166 W G CM=M04aa DMC�o • a • I It czy m r m D 0 { m 0 n 0 v z I t�) ✓ r + ') ✓ �.wJ r r 1 - T r I I I I • ' I I i t ✓ ▪ te . Mw lA I arwt Ii lwiMf}� I I I _ _ w owes _ rimalooaaa ten IN VI xi 0 / I II II 4 , III I I II I II 1 ei w� a ww - L r ""l NM w • • w- • - w.- — r « -I.e . IrrITI"'rT1 • I C: I 1I 1 . 1r � - T9 cr I I 1 I 1 �� tr 1 tr .JL, _ _ _ .JL _ Jr _ 1 J — r MELD VERIFIED i E m r y m :0=∎ ••0_07. 0 =0 X7.0 41:411_0:0 0_41■=•_40:0 0 v_114_•► •• :0 0 •_• ∎_ ∎_•:.411.0•WO 41►_w =• •• I W O • ••4 ■ 4 ∎ `' ∎ i ∎4. ∎ ∎ . ''' ∎4 ∎ O rr r 'A ► `i 4 'r 4 ''' 4 7 4 '`" 4 v•:■ 4 ∎ • 1• i' '4 4 p hi i! j � , / ( ■ 7 .674:7.4•Ter.11:•;:•Z•11,7,•■■:47•7■7alz'a2 g t VT; $rq r 6 I g �D 4°Y a p 11 0 N r r z �. m r Z ' co ✓ a N $ - rn r ai --1 m v M (.0 Pacific Stainless Products, Inc. 10100 /SW Allen Blvd. - Beaverton, Oregon 97005 Tel. (503) 641-7%0 - Fax. (503) 646 -2348 * * ** MONROE, WA. Tel. (360) 794 -7709 - Fax. (360) 794 --8182 DRAWING NO: T / TITLE: D DRAWN 6Y: C - - -- - - . . CT C 4 TE f NG P 156 & 5 5 NELSON L ACE D DATE. e JOB NO: S SCALE: a p Q �° �° a a ° 11 f5A 1:11 r 0 " isry 0 Z v N rn o rn 0 0 D mm i=o r r rn ,. ..11 0r-. - - -4=1%.01M ig /45 9'•0 FIELD VERIFIED m Fl E grA < l'`E P 51 to : air §rTIA OP' so C 1843/4 4OOF LINE 14 -0' F VER CP N V ){ A, s ar ♦rrArAMLMA'ItAZVA A 20A A I► A lI ♦ . L 0 A ZI A 7 A 7 A 7 ♦ 0 A ∎ A ZI L M A y A 7 AZ V AZIA ∎ AZ ► I A , A W AL W A A Ir 7 A 0 A M► It AZ V A rr A .V A�A • W W. A vI W I AMf. 10 V 2 70 m N 4 Pacific Stainless Products, Inc. 10100 /SW Allen Blvd. - Beaverton, Oregon "17005 Tel. (503) 641 -7060 - Fax. (503) 6462348 * * ** MONROE, WA. Tel. (360) 7 "14 -770"1 - Fax. (360) 7"14 -8182 DRAWING N0: TTO& el TITLE: T `I La � � T � '� (1 �l� I �i 5 ON NELSON I L A �,�. Sale& DRAWN BY: DRS CHECKED: D.S. REVISION: 0 a © i 1G ion herein by P ai`st•� °ty�c ouf a Stainless Prod , and except for rights ustomer, Pacific ghts expressly eronted to customer, in- c less Products, Inc. reserves all patent, proprietary, design, mcg/jkacturitl *Id repr rights thereto • / - - O F 15665 TUKW A _ —_ —---- . DATE: 12/0`1 /06 JOB NO: 8 0044642 SCALE: NOTED 1 - -__ Q Q 0 ° a • • • J • • • %aft 1I m r rn m E 0 n 0 z rn ww, rn Pacific Stainless Products, nn , Inn " , nn � ▪ i �---- - -'1� I nn ; i^ �`,il UU I I III dl UU I I Ip MI nn I W t. — �rrrrr.r . UU w - � r :.tr•.tr - - — b 4 nn nn � I amaamlwsslats4 �Im mmas>3m>m>rm� nn � � _) n n ( ^ ^� nn i i nn nn ^ (-- — nn II II nn ; i r . ti p . o � nn i r UV L - -- � _ _1__-,...____ - - rii - - 1 r n - - f , rr i - -- I, I 1 I III • • I 0I I n I III l II L ° 1 eww IT ..p.......,‘ I 1r) I 1 IN "le li J 1 1 w •. I 1) L J J 1 � L ' ' J 1 v pi r •,1 r , 1 I I ' :,., I I r1 I • I I 1 . I i1 1 i tk, 1 1 J 1 Z,\ fl 1 L � � J ; 1 L`� J J I I A - -1 I - -,r i r L r -- sr I "- J J I p 11 410. mi . ; , 1; J 1 11 ! 0 C, I 1.- w1 .�w_ .I-r-I.Lz vi w.w���.www J1J T -II- I gi Ir I I� r 1 Li 4w ■w■■■w t 1 .� 1. .. 1 rl I 1 n 1 / 1 w w -ww -5— 1fa w... w- - .{,�,,�� III alr 0 eel r \ O * I r , 4 ?+ �� - - - f \ V r - - 1 I t ' 1 t I , I t J L I wr II , 1N 'F a O`; u -. 3; wr in U U ci 82 al O — a m� MID 1•:41KID =O 0 41, :•_11.0 ■∎:∎ 4 I K.4 0: 4;.■:11■.:7w 0 =11■=m =0 0:111:0:11:111.: :0:41K11 o: 410.:∎ m 'Y./MO . :Ag rA�AYA7174•Tr VIIM ran wiv ∎ ∎ ∎ ∎ ∎r∎ ∎v ∎v74012. r•Lr. • r r'��A ∎ ∎•67.∎ •■' 11v4 'C•WA . r -+ gi 0 N 0:0:0:4► ■∎ 0 4Ai0 0:4•7 O:0: ∎I0 0 :417. c1 WOZe 0 :4 W.: � •_a •:.0 ■∎ 4 1:0:40:11:0:•:41 0:0:111:410:0:01:7 A "`Q► ∎*.:w ∎A.r ∎ ∎4 'vaATA fir's °A AY. `' rAvA ∎. YA•A`' r Ay1. : A g.s! igiR A 'G2 T t • "" I I 0 1 z rn N A j s 3 D r rrt Z to (")b II D X r r „).< _ f � N a Inc. 10100 /511 Allen Blvd. - Beaverton, Oregon 87005 Tel. (503) 641 -7060 - Fax. (503) 646 -2348 * * ** MONROE, WA. Tel. (360) 7c14 -770c1 - Fax. (360) 7q4 -6182 DRAWING NO: TTO& ill O TITLE: C T CA TE 1 N L DRAWN BY: CHECKED: REVISION: . I n e 'in�formati information arid is the property of u. except for rights expressly granted to the customer, s, P Inc. j r ' reserves di patent, proprietary, design, uses reproduction thhere �O N�.�. ON • DATE: 12/01 /06 JOB NO: 0044642 SCALE: NOTED TUKWILA LUA. Selea P Q ®ED M C-� 4 43 a 0 G�1 C� o r • : -CZ) 5 4 r. • m z 0 N m m Z 0 N m z rn z z 0 0 0 m -- Me WO ell - f —J r ij I T m m 1 0 F FIELD veRIPIED rn 9 r "I I- - -i 1 1 1 1 1 1 I I r.■ ' L - 1 ROOF L 1NE 184 3/4 14' -O" FIELp vERIRIED .. \ \\ Q 151 i : a � ;c 71 r 0) T 'A 1 z rn r —4 __ .. IL — II C ' I II I I II I I I II 1 I II I G; I II I *---....4-.--1 rn X Pacific Stainless Products, Inc. 10100 /SW Allen Blvd. - Beaverton, Oregon 87005 Tel. (503) 641 -7060 - Fax. (503) 646 -2348 * * ** MONROE, WA. Tel. (36.0) 7q4 -770q - Fax. (360) 7q4 -SIS2 I DRAWING N 0: T T 0 & l'' 1 / 0 1 F T ITLE: 1 _ �� t DI � � �� � (�� I I N L 5 ON �� � (� g S 1 C E - DRAWN BY: p CHECKED: � S. REVISION: paCITIC i n 1 I erei T ,n f wcs�originated d by a nd nn the property of Pacific Skinless Products, Irn. Grid except for rights expressly granted to the cuatarner, Pacific Stain- less Products, Inc. reserves oil Potent, pr c n d e mcru p roduction rights thereto - J • DATE. �Z �O��f�r0 JOB N0: 0044642 SCALE: SCALE: SS p Q ., o M co 4 a3 a 0 Ctrl 6 o • TI I If ;: z N m z rn iU 0 b r m r �. 9' -0' J co O 0 ,.r J I D mm r V 6 r g 1 N g Q 4 1 N coj 1' z rn MIN 1■1 I J m X Pacific Stainless Products, Inc. 10100 /SW Allen Blvd. - Beaverton, Oregon 87005 Tel. (503) 641 -7060 - Fax. (503) 646 --2348 * * ** MONROE, kA. Tel. (360) 7q4 -770q - Fax. (360) 7q4 -5182 DRAWING NO: e aciii ii, / 0 1 F 4 TITLE: �� CATERING DRAWN 6Y: �� CH ECKED: O. S. R EVISION: acs ic � ai The was or originated Pacific s expressly granted to the and except for right customer, Pacific Stain- less Products, Inc, reserves all use, e, , reams act design, and r producti rights thereto - 15665 T� ,UJ N E L S ON i� LACE I L UM, 981663 • DATE. 12/01/06 JOB NO: 0044 042 SCALE: NOTED p G°� . C) M C� �i' . a Q C C� o , e • I !ql ig r 4 H O r - (p m � �0 0 � m p -e) 0) Ai 3 0 0 1 ' C 3 0' I r rn L m A 40.•01 1 1 22 x 44 ----f / I3 x lc) a N) N r D D � S 2 mrn � n� '— D r X Imo) 2 m m-2—t6 tog N �1 y -- � ■— __... - -- —te A A A A a oe i X _ 0' A �� N S Pacific Stainless Products, Inc, 10100 /5141 Allen Blvd. - Beaverton, Oregon 87005 Tel. (505) 64I -7060 - Fax. (505) 646 -2348 * * ** MONROE, WA. Tel. (560) 7q4 -770q - Fax. (360) 7q4 -8182 HOOD ITEM NUMBER A HOOD LENGTH (IN.) B HOOD WIDTH (IN.) C HOOD HEIGHT (IN.) HOOD WT. (LBS.) TOTAL HOOD EXHAUST (CFM) EXHAUST COLLAR SIZE (IN.) DUCT COLLAR VELOCITY (FPM) TOTAL COLLAR STATIC PRESSURE EXHAUST BAFFLE AREA (SQ. FT.) EXHAUST AMOUNT EA. BAFFLE (CFM) EXHAUST VELOCITY EA. BAFFLE (FPM) STATIC PRESSURE EA. BAFFLE TOTAL M.U.A. SUPPLY (CFM) SUPPLY COLLAR SIZE (IN.) SUPPLY COLLAR VELOCITY (FPM) TOTAL SUPPLY STATIC PRESSURE HOOD FACE • SUPPLY GRILLE LIGHT FIXTURE QUANTITY LIGHT VOLTAGE WATTS/ PHASE VH1 120 48+3 24 350 2 600 14"x 14" 1910 1 2.25 433 318 .23 * * * * * 2 115v -1 ph fl V L 4" `Ii " fiai . `a X A .� 53 c, ' � w; 2- em - u ko :k 2 2084a1 te Pacific Stainless 0 :NOISIA3e1 4g LON :31VOS CHECKED: D. S. :ON 80f DRAWN BY: DIZI4I :3140 LL r 4 COMPONENT NO10604 UL LISTED INCANDESCENT FIXTURE ISSUE NO. A- 39,774 HOOD LIGHT • VENTMATIC AIR SYSTEMS • MEETS NFPA CODE 96 AND NEC 410 • SPECIFICALLY DESIGNED FOR CANOPY HOODS • INCANDESCENT — RATED FOR 100 WATTS BAFFLE FILTER MANUFACTURED BY KASON AVAILABLE IN: STAINLESS STEEL BAFFLE STYLE FILTER ALUMINUM BAFFLE STYLE FILTER GREASE FILTER CLASSIFIED BY UNDERWRITERS LABORATORIES, INC.. AS TO FLAMMABILITY AFTER EXPOSURE TO GREASE LADEN AIR UL FILE flR 13192 96.4% FLYER EFFICIENT AT GREASE EX1WUCDON GENERAL NOTES: (UNLESS OTHERWISE NOTED) 1) VENTILATION HOOD TO BE SECURELY ATTACHED TO STRUCTURAL CONSTRUCTION BY OTHERS PER LOCAL, STATE AND FEDERAL CODES. 2) VENTILATION HOOD MUST BE INSTALLED PLUMB AND LEVEL FOR PROPER OPERATION. 3) ALL NOTES AND DIMENSIONS MARKED WITH AN ASTERISK (1 MUST BE VERIFIED. ITEMS NOT VERIFIED WILL BE ASSUMED CORRECT. 4) EXHAUST AND MAKE -UP AIR SYSTEMS SHALL BE CONNECTED BY AN ELECTRICAL INTER LOCK SWITCH BY ELECTRICAL CONTRACTOR. 5) ALL CONSTRUCTION, PLUMBING AND ELECTRICAL MUST MEET WITH LOCAL, STATE AND FEDERAL CODES. 6) PACIFIC STAINLESS PRODUCTS IS NOT RESPONSIBLE, OR LIABLE FOR IMPROPER FUNCTION ATTRIBUTABLE TO STATIC PRESSURE, AIR VOLUME, OR INSTALLATION OTHER THAN THAT INDICATED AND /OR SPECIFIED. DESIGN SPECIFICATION VENTMATIC VENTILATION HOOD MANUFACTURED BY PACIFIC STAINLESS PRODUCTS, INC. 10100 SW ALLEN BLVD., BEAVERTON, OR., 97005 VENTMATIC HOOD SYSTEMS ARE FABRICATED FROM STAINLESS STEEL WHERE EXPOSED, EXTERNAL SEAMS ARE WELDED LIQUID TIGHT AND ALL EXPOSED SURFACE WILL BE POLISHED TO A #4 FINISH. THE VENTILATION HOODS ARE BUILT IN COMPLIANCE WITH NFPA STANDARD #96, & U.L. CLASSIFIED, AND IS NSF APPROVED, THE HOOD VILL HAVE A FULL LENGTH SEMI - CONCEALED GREASE TRACK THAT WILL PITCH TO A REMOVABLE GREASE COLLECTOR. GREASE EXTRACTORS TO BE U.L. CLASSIFIED BAFFLE TYPE FILTERS MOUNTED AT NO LESS THAN A 45 DEG. ANGLE AND WILL BE LOCKED IN PLACE DURING NORMAL OPERATION BY MEANS OF AN UPPER HOLDING TRACK AT THE TOP OF THE FILTER. THE HOOD WILL BE EQUIPPED WITH U.L. LISTED LIGHT FIXTURES SUITABLE FOR 100 WATT INCANDESCENT BULBS WITH PLASTIC COATED GLASS BULB AND WILL BE PRE -WIRED TO A SINGLE CONNECTION POINT. ETL Listed, NFPA & NSF Ventmatic Installation Manual Hood CFM: Low Temp Equipment Mid Temp Equipment High Temp Equipment or Smoke Producing Minimum CFM Moximum CFM 260 CFM 0 Linear Ft. 280 CFM 0 Linear Ft. 300 CFM 0 Linear Ft. 260 CFM 0 linear Ft. 350 Cal 0 Linear Ft. Greose extraction fillers to be aluminum or stainless steel. Hood Fights to be connected to separate wall switch. Access for wiring located on top. Exhaust fon to be connected to separate power source and interlocked to supply oar fan. Mog starter heaters and circuit breaker to be sized to motor ampocity. Clearances from combustible material: Top 18" Side 18" Front 18' Bock 18" The above clearances con be reduced to 3' if one hour material is used for surrounding material. Hanging: Hood should be hung from wog frame and front hungers suppled with hood. Front hanger rod to be not less than 3/8' inch oN threod. with double nuts at both ends. Bock hanger to be not less than 110 x 1 1/2 sheet metal screw, 24" on center and lock weld to stoin ess steel wolf frame_ Refer to detail droving No. T. The exhaust hood must be hung level in order for grease to properly droin. Roof and ceiling supports to be odequote to support hood weight. Verify hood overhang, height and exact location with approved Job site drawings Exhaust hoods with fire dumpers in the exhaust of makeup air -duct corors require access for maintenance and inspection. Exhaust outlet to be connected to approved grease duct. Connection to be continuous welded joint. Makeup air inlet to be connected to approved Uniform Mechanical Code Standard for metal, fiberboard and flexible duct. lotion required on on ducting on system with tempered dr. Tempered oir recommended on system exceeding 2000 CFM. and area where outdoor temperatures drop below 45 degrees F. All exhaust tons. supply fans, curbs, exhaust ducts makeup o:r -duct, hood enclosure ponels, etc.. must be installed to the latest e6tion of NFPA 96, and the recognized building code where the exhaust hood is being installed. / isiralrasmai VERN Yr ELECTRICAL JUNCTION 80X (VERIFY LOCATION) ETL LISTED FILE *2001066 VENTMATIC EXH. HOOD THE EXHAUST VENTILATOR CONFORMS TO U.L-ST NOARO -710 'EXHAUST HOODS FOR COMMERCIAL E OOKRIG EOUIPNENT'. Pes • BY PACIFIC STAINLESS PRODUCTS INC. FLUTED STYLES 'STANDARD' (FLUTING 6' 4 or - O.C.) HOOD MODEL: CDW - 120 60 (VERIFY LOCATION) **MAXIMUM --� — FRONT TO BACK EXHAUST DUCT AREA • HOOD LIGHTS 14 14 LIGHTS AND ACCESSORIES CONDUITS LOCATED OUTSIDE OF HOOD TOP PANEL AREA A PLAN vIEW r a r ELEVATION VIEW EXHAUST DUCT COLLAR 0 ALL - THREAD HANGER BRACKET TYP. (4x) 1 F i I I I I I 1 I I 1 I 1 I I I I I I I I 3' WOOD WALL FRAME 3 C 1 • FI><EOO 153F ACKET (DETAIL 2r--- 14 SECTION VIEW Mb b t EXHAUST DUCT COLLAR 4 51v GRE 5/5 BAFFLE FILTER REVIEW p � C CODE OOr 1 tIIALL ` a A . i la OI TvkWlSt BIALOD CUSTOMER APPROVAL FOR MANUFACTURE APPRCNED AS NOTED APPQD ED WITHOUT EXCEPTION REVISE ANO RESUBMIT SIGNATURE 0 0 0 NAME DATE • RECENED r6- T1 Dti: 14 71.,'C.5 — e. l - . - —_ Pfll.:,ti in:.WER iA Nr r- 0 (0 6 I 1 0 0 In 4 LU O 4E 1 O O O V C 1 Pacific Stainless Products cI7005 Tel. HOOD ITEM NUMBER A HOOD LENGTH (IN.) B HOOD WIDTH (IN.) C HOOD HEIGHT (IN.) HOOD WT. (LBS.) TOTAL HOOD EXHAUST (CFM) EXHAUST COLLAR SIZE (IN.) DUCT COLLAR VELOCITY (FPM) TOTAL COLLAR STATIC PRESSURE EXHAUST BAFFLE AREA (SQ. FT.) EXHAUST AMOUNT EA. BAFFLE (CFM) EXHAUST VELOCITY EA. BAFFLE (FPM) STATIC PRESSURE EA. BAFFLE TOTAL M.U.A. SUPPLY (CFM) SUPPLY COLLAR SIZE (IN.) SUPPLY COLLAR VELOCITY (FPM) TOTAL SUPPLY STATIC PRESSURE HOOD FACE SUPPLY GRILLE LIGHT FIXTURE QUANTITY LIGHT VOLTAGE WATTS/ PHASE VH2 120 +3 48 +3 24 350 3000 14 "x 15" 2058 .875 2.25 500 343 .30 * * * * * 2 115v -1 ph xi V61-1411111 .� _1; sti 4-1,2igiP .. B u >. _;.) ( v, x w 3 cue V a& �2 2 )1(264ai .1 SSaILIIBaS ° O :NOISIAl2:1 SCALE: NOTED CHECKED: D. S. JOB NO: 0044642 DRAWN BY: OR-4 90 /LO /Zl :31y0 • y i 1 I I N V h In O N ..."---- 70& t • 1 I COMPONENT NO10604 UL LISTED INCANDESCENT FIXTURE ISSUE NO. A- 39,774 HOOD LIGHT • VENTMATIC AIR SYSTEMS • MEETS NFPA CODE 96 AND NEC 410 • SPECIFICALLY DESIGNED FOR CANOPY HOODS • INCANDESCENT - RATED FOR 100 WATTS BAFFLE FILTER MANUFACTURED BY KASON AVAILABLE IN: STAINLESS STEEL BAFFLE STYLE FILTER ALUMINUM BAFFLE STYLE FILTER GREASE FILTER CLASSIFIED BY UNDERWRITERS LABORATORIES. INC.® AS TO FLAMMABILITY AFTER EXPOSURE TO GREASE LADEN AIR UL FILE flR 13192 S6-4X FILTER EFFICIENT AT CREASE EXTRACTION GENERAL NOTES: (UNLESS OTHERWISE NOTED) 1) VENTILATION HOOD TO BE SECURELY ATTACHED TO STRUCTURAL CONSTRUCTION BY OTHERS PER LOCAL, STATE AND FEDERAL CODES. 2) VENTILATION HOOD MUST BE INSTALLED PLUMB AND LEVEL FOR PROPER OPERATION. 3) ALL NOTES AND DIMENSIONS MARKED WITH AN ASTERISK (•) MUST BE VERIFIED. ITEMS NOT VERIFIED WILL BE ASSUMED CORRECT. 4) EXHAUST AND MAKE -UP AIR SYSTEMS SHALL BE CONNECTED BY AN ELECTRICAL INTER LOCK SWITCH BY ELECTRICAL CONTRACTOR. 5) ALL CONSTRUCTION. PLUMBING AND ELECTRICAL MUST MEET WITH LOCAL, STATE AND FEDERAL CODES. 6) PACIFIC STAINLESS PRODUCTS IS NOT RESPONSIBLE. OR LIABLE FOR IMPROPER FUNCTION ATTRIBUTABLE TO STATIC PRESSURE. AIR VOLUME, OR INSTALLATION OTHER THAN THAT INDICATED AND /OR SPECIFIED. DESIGN SPECIFICATION VENTMATIC VENTILATION HOOD MANUFACTURED BY PACIFIC STAINLESS PRODUCTS, INC. 10100 SW ALLEN BLVD., BEAVERTON, OR., 97005 VENTHATIC HOOD SYSTEMS ARE FABRICATED FROM STAINLESS STEEL WHERE EXPOSED, EXTERNAL SEAMS ARE WELDED LIQUID TIGHT AND ALL EXPOSED SURFACE WILL BE POLISHED TO A 04 FINISH. THE VENTILATION HOODS ARE BUILT IN COMPLIANCE WITH NFPA STANDARD 096, & U.L. CLASSIFIED, AND IS NSF APPROVED, THE HOOD WILL HAVE A FULL LENGTH SEMI - CONCEALED GREASE TRACK THAT WILL PITCH TO A REMOVABLE GREASE COLLECTOR. GREASE EXTRACTORS TO BE U.L. CLASSIFIED BAFFLE TYPE FILTERS MOUNTED AT NO LESS THAN A 45 BEG. ANGLE AND WILL BE LOCKED IN PLACE DURING NORMAL OPERATION BY MEANS OF AN UPPER HOLDING TRACK AT THE TOP OF THE FILTER. THE HOOD WILL BE EQUIPPED WITH U.L. LISTED LIGHT FIXTURES SUITABLE FOR 100 WATT INCANDESCENT BULBS WITH PLASTIC COATED GLASS BULB AND WILL BE PRE -WIRED TO A SINGLE CONNECTION POINT. ETL Listed, NFPA & NSF Ventmatic Installation Manual Hood CFM: Low Temp Equipment Mid Temp Equipment High Temp Equipment or Smoke Producing Minimum CFM Maximum CFM 260 CFM 0 Linear Ft. 280 CFM ® Linear Ft. 300 CFM 0 Linear Ft. 260 CFM 0 Linear Ft. 350 CFM 0 Linear Ft. Grease extraction fillers to be aluminum or stainless steel. Hood lights to be connected to separate wall switch. Access for wiring located on top. Exhaust fon to be connected to separate power source and interlocked to supply air fon. Log starter heaters and circuit breaker to be sized to motor ompocity. Clearances from combustible material: Top 18" Side 18' Front 18' Bock 18' The above clearances con be reduced to 3' it one hour material is used for surrounding material. Honging: Hood should be hung from wog frame and front hangers supplied with hood. Front hanger rod to be not less than 3/8' inch all thread. with double nuts at both ends. Bock hanger to be not less than 110 x 1 1/r sheet metal screw. 24' on center and Lock weld to stainless steel woll frame. Refer to detoi drawing No. 1. The exhaust hood must be hung level in order for grease to properly drain. Roof and ceiling supports to be adequate to support hood weight. Verify hood overhang. height and exact location with approved Job site drawings Exhaust hoods with fire dampers in the exhaust of makeup air -duct colors require access for maintenance and inspection. Exhaust outlet to be connected to approved grease duct. Connection to be continuous welded joint. Makeup air inlet to be connected to approved Uniform liechonicd Code Stondord for metal, feerboord and Rexible duct. Irsulction required on oti ducting on system with tempered air. Tempered air recommended on system exceeding 2000 OEM, and area where outdoor temperatures drop below 45 degrees F. All exhaust fans. supply fans. curbs. exhaust ducts. makeup air-duct, hood enclosure panels, etc.. must be installed to the latest edition of NFPA 96. and the recognized bulldog code where the exhaust hood is being installed. VERFR F11C Lgswe'Eammiej FM ELECTRICAL JUNCTION BOX 3' ! WALL 7 3 FRAM ETL LISTED FILE *2001066 VENTMATIC EXH. HOOD THE EXHAUST VENIIIATOR CONFORMS TO U.L_STANDARD -710 'EXHAUST HOODS FOR COMMERCIAL COOKING EQUIPMENT'. BY PACIFIC STAINLESS PRODUCTS INC. HOOD MODEL: CDW - 120 6129 1/2 16' MAXIMUM --T — FRONT TO BACK EXHAUST DUCT AREA (VERIFY LOCATION) HOOD LIGHTS LIGHTS AND ACCESSORIES CONDUITS LOCATED OUTSIDE /---OF HOOD TOP PANEL AREA A EXHAUST DUCT COLLAR 14 2 -\) ALL - THREAD HANGER BRACKET TYP. (4x) FLUTED STYLES STANDARD' (FLUTING 6' • or - O.C.1 J I I I I I I I I I I I PLAN vIEUJ 15 ELEVATION VIEW 13/S B C 1 • • 3' HOOD WALL FRAME ALL- THREAD HANGER BRACKET FIXES: E3RACI<eT DETAIL SECTION VIEW f----14 /1 EXHAUST DUCT COLLAR 5/5 BAFFLE FILTER WALL FRAME R MOVABLE WS GREASE CUP R eWE IN C4aE CO��,Arn N 2::1-:.: - f ow � n NRctnN $ Ui�o RECE7 Ott; 1 2005 PC-s tit' 4 =cc1 CUSTOMER APPROVAL FOR MANUFACTURE APPROVED AS NOTED APPROVED WITHOUT EXCEPi1ON REVISE TWO RESUBMIT %NATURE O O O ATE i • x II- I EP O U C 4 17005 Tel. HOOD ITEM A HOOD LENGTH (IN.) B HOOD WIDTH (IN.) C HOOD HEIGHT (IN.) HOOD WT. (LBS.) TOTAL HOOD EXHAUST (CFM) EXHAUST COLLAR SIZE (IN.) DUCT COLLAR VELOCITY (FPM) TOTAL COLLAR STATIC PRESSURE EXHAUST BAFFLE AREA (SQ. FT.) EXHAUST AMOUNT EA. BAFFLE (CFM) EXHAUST VELOCITY EA. BAFFLE (FPM) STATIC PRESSURE EA. BAFFLE TOTAL M.U.A. SUPPLY (CFM) SUPPLY COLLAR SIZE (IN.) SUPPLY COLLAR VELOCITY (FPM) TOTAL SUPPLY STATIC PRESSURE HOOD FACE SUPPLY GRILLE LIGHT FIXTURE QUANTITY LIGHT VOLTAGE/ WATTS/ PHASE VH3 132 48 +3 24 385 2860 14"x16" 1839 .75 2.25 477 306.5 .10 * * * * * 2 115v --1 ph -.eo .411%412 liWnglill V .� • �x s , u. t...- la a. in 43/4 Pacific Stainless 0 :NOISIAli SCALE: NOTED CHECKED: D. S. :ON 8Or DRAWN BY: D IR f4 °JO /1-0 /Zl :31dd " ILE CATERI Li_ c () lin O 1 70i&ocT1 t • COMPONENT N010604 UL LISTED INCANDESCENT FIXTURE ISSUE NO. A- 39,774 HOOD LIGHT • VENTMATIC AIR SYSTEMS • MEETS NFPA CODE 96 AND NEC 410 • SPECIFICALLY DESIGNED FOR CANOPY HOODS • INCANDESCENT — RATED FOR 100 WATTS BAFFLE FILTER MANUFACTURED BY KASON AVAILABLE IN: STAINLESS STEEL BAFFLE STYLE FILTER ALUMINUM BAFFLE STYLE FILTER GREASE FILTER CLASSIFIED BY UNDERWRITERS LABORATORIES. INC.. AS TO FLAMMABILITY AFTER EXPOSURE TO GREASE LADEN AIR UL FILE 11R13192 96.4% FILTER EFFICIENT AT GREASE EXIRACDON GENERAL NOTES: (UNLESS OTHERWISE NOTED) 1) VENTILATION HOOD TO BE SECURELY ATTACHED TO STRUCTURAL CONSTRUCTION BY OTHERS PER LOCAL, STATE AND FEDERAL CODES. 2) VENTILATION HOOD MUST BE INSTALLED PLUMB AND LEVEL FOR PROPER OPERATION. 3) ALL NOTES AND DIMENSIONS MARKED WITH AN ASTERISK ( *) MUST BE VERIFIED. ITEMS NOT VERIFIED WILL BE ASSUMED CORRECT. 4) EXHAUST AND MAKE-UP AIR SYSTEMS SHALL BE CONNECTED BY AN ELECTRICAL INTER LOCK SWITCH BY ELECTRICAL CONTRACTOR. 5) ALL CONSTRUCTION. PLUMBING AND ELECTRICAL MUST MEET WITH LOCAL, STATE AND FEDERAL CODES. 6) PACIFIC STAINLESS PRODUCTS IS NOT RESPONSIBLE. OR LIABLE FOR IMPROPER FUNCTION ATTRIBUTABLE TO STATIC PRESSURE, AIR VOLUME. OR INSTALLATION OTHER THAN THAT INDICATED AND /OR SPECIFIED. DESIGN SPECIFICATION VENTMATIC VENTILATION HOOD MANUFACTURED BY PACIFIC STAINLESS PRODUCTS, INC. 10100 SW ALLEN BLVD., BEAVERTON, OR., 97005 VENTMATIC HOOD SYSTEMS ARE FABRICATED FROM STAINLESS STEEL WHERE EXPOSED, EXTERNAL SEAMS ARE WELDED LIQUID TIGHT AND ALL EXPOSED SURFACE WILL BE POLISHED TO A 04 FINISH. THE VENTILATION HOODS ARE BUILT IN COMPLIANCE WITH NFPA STANDARD 1196, & U.L. CLASSIFIED, AND IS NSF APPROVED, THE HOOD WILL HAVE A FULL LENGTH SEMI - CONCEALED GREASE TRACK THAT VILL PITCH TO A REMOVABLE GREASE COLLECTOR. GREASE EXTRACTORS TO BE U.L. CLASSIFIED BAFFLE TYPE FILTERS MOUNTED AT NO LESS THAN A 45 DEG. ANGLE AND WILL BE LOCKED IN PLACE DURING NORMAL OPERATION BY MEANS OF AN UPPER HOLDING TRACK AT THE TOP OF THE FILTER. THE HOOD WILL BE EQUIPPED VITH U.L. LISTED LIGHT FIXTURES SUITABLE FOR 100 WATT INCANDESCENT BULBS VITH PLASTIC COATED GLASS BULB AND WILL BE PRE -WIRED TO A SINGLE CONNECTION POINT. ETL Listed, NFPA & NSF Ventmatic Installation Manual Hood CFM: Low Temp Equipment Mid Temp Equipment High Temp Equipment or Smoke Producing Minimum CFM Maximum CFM 260 CFM 0 Linear Ft. 280 CFM 0 Linear Ft_ 300 CFM 0 Linear Ft. 260 CFM 0 Linear Ft. 350 CFM 0 Linear Ft. Grease extraction fillers to be aluminum or stoinless steel. Hood lights to be connected to seporote wall switch. Access for wiring located on top. Exhaust fon to be connected to separate power source and interlocked to supply air fon. Mog starter heaters and circuit breaker to be sized to motor ompocity. Deoronces from combustible material: Top 18" Side 18' Front 18" Bock 18" The above clearances con be reduced to 3" if one hour material is used for surrounding material. Hood should be hung from wall frame and front hangers supplied with hood. Front hanger rod to be not less than 3/8' inch o1l thread. with double nuts at both ends. Sock hanger to be not less thorn 110 x 1 1/2" sheet metal screw. 24" on center and tack weld to stainless steel wall frame. Refer to detail drawing No. I. The exhaust hood must be hung level in order for grease to property drain_ Roof and ceifirg supports to be odequote to support hood weight_ Verify hood overt height and exoct location with approved Job site drawings Exhaust hoods with fire dampers in the exhaust of makeup oir -duct collars require access for maintenance and inspection. Exhoust outlet to be connected to approved grease duct_ Connection to be continuous welded joint. Makeup air inlet to be connected to approved Uniform Mechanical Code Standard for metal, fiberboard and flexible duct. Insulation required on all ducting on system with tempered air_ Tempered air recommended on system exceeding 2000 CFu. and area where outdoor temperatures drop below 45 degrees F. NI exhaust fans, soppy fans, curbs, exhaust ducts. makeup air —duct, hood enclosure ponds, etc.. must be installed to the latest edition of NFPA 96, orld the recognized build :rig code where the exhaust hood is being installed. MEEICE Ref BY PACIFIC STAINLESS PRODUCTS INC ELECTRICAL JUNCTION BOX (VERIFY LOCATION) ETL LISTED FILE *2001066 VENTMATIC EXH_ HOOD THE EXHAUST VENTILATOR CONFORMS TO U.L-STANDARD -710 'OO{AUST HOODS FOR COMMERCIAL COOKING EQUIPMENT'_ • FLUTED STYLES 'STANDARD' (FLUTING 6' 4 or - O.C.) HOOD MODEL: CDW - 132 l8 (VERIFY LOCATION) 16' MAXIMUM J — FRONT TO BACK EXHAUST DUCT AREA • LIGHTS AND ACCESSORIES CONDUITS LOCATED OUTSIDE z --OF HOOD TOP PANEL AREA !HOOD LIGHTS A PLAN VIEW Af 14 — ELEVATION VIEW • EXHAUST DUCT COLLAR 1 1/4 ALL - THREAD HANGER BRACKET TYP. (4x) - 1 3/8 1 I I I I I I I I I I I I I I I I I I I I 1 3/8 • 3'14000 WALL 3 'C FRAME C 1 FIXED 15I RACKET DETAIL HOOD LIGHT 1 0 1 EXHAUST DUCT COLLAR 4 - SECTION VIEW 01) 518 BAFFLE FILTER WALL FRAM REMOVABLE 515 GREASE OP REVIEWED fOR COMPLIANC I CODE inn AN 2 4 1:.t3= I Tukwila la I DIVISION City Of DNt !ice i- -.1.: OW 147005 i CUSTOMER APPROVAL FOR MANUFACTURE APPROVED AS NOTED APPROVED WITHOUT EXCEPTION REVISE AND REST SIGNATURE 0 0 0 NAME DATE • -1E • 7q4-770G1 - HOOD ITEM NUMBER A HOOD LENGTH (IN.) B HOOD WIDTH A (IN.) C HOOD HEIGHT (IN.) HOOD WT. (LBS.) TOTAL HOOD EXHAUST (CFM) EXHAUST COLLAR SIZE (IN.) DUCT COLLAR VELOCITY (FPM) TOTAL COLLAR STATIC PRESSURE EXHAUST BAFFLE AREA (SQ. FT.) EXHAUST AMOUNT EA. BAFFLE (CFM) EXHAUST VELOCITY EA. BAFFLE (FPM) STATIC PRESSURE EA. BAFFLE TOTAL M.U.A. SUPPLY (CFM) SUPPLY COLLAR SIZE (IN.) SUPPLY COLLAR VELOCITY (FPM) TOTAL SUPPLY STATIC PRESSURE HOOD FACE SUPPLY GRILLE LIGHT FIXTURE QUANTITY LIGHT VOLTAGE WATTS/ PHASE VH4 132 48+3 24 r 385 2860 14"x16" 1839 .75 2.25 477 306.5 .10 * * * * * 2 115v -1 ph 1 .1V u ° t N •- 'vCC �_ 8. u 3 ., Vs L 3i rc# E �xev na, 2 ita 1 -. v0. iX L Pacific Stainless REVISION: 0 SCALE: NOTED CHECKED: D. S. JOB NO: 0044 42 DRAWN BY: DI? JO /L al :31y0 O .r— r t • i COMPONENT N010604 UL LISTED INCANDESCENT FIXTURE ISSUE NO. A- 39,774 HOOD LIGHT • VENTMATIC AIR SYSTEMS • MEETS NFPA CODE 96 AND NEC 410 • SPECIFICALLY DESIGNED FOR CANOPY HOODS • INCANDESCENT — RATED FOR 100 WATTS BAFFLE FILTER MANUFACTURED BY KASON AVAILABLE IN: STAINLESS STEEL BAFFLE STYLE FILTER ALUMINUM BAFFLE STYLE FILTER GREASE FILTER CLASSIFIED BY UNDERWRITERS LABORATORIES. INC.® AS TO FLAMMABILITY AFTER EXPOSURE TO GREASE LADEN AIR UL FILE 1R13192 96.4% FLIER Emma AT GREASE EXTRACTION GENERAL NOTES: (UNLESS OTHERWISE NOTED) 1) VENTILATION HOOD TO BE SECURELY ATTACHED TO STRUCTURAL CONSTRUCTION BY OTHERS PER LOCAL, STATE AND FEDERAL CODES. 2) VENTILATION HOOD MUST BE INSTALLED PLUMB AND LEVEL FOR PROPER OPERATION. 3) ALL NOTES AND DIMENSIONS MARKED WITH AN ASTERISK (s) MUST BE VERIFIED. ITEMS NOT VERIFIED WILL BE ASSUMED CORRECT. 4) EXHAUST AND MAKE -UP AIR SYSTEMS SHALL BE CONNECTED BY AN ELECTRICAL INTER LOCK SWITCH BY ELECTRICAL CONTRACTOR. 5) ALL CONSTRUCTION. PLUMBING AND ELECTRICAL MUST MEET WITH LOCAL, STATE AND FEDERAL CODES. 6) PACIFIC STAINLESS PRODUCTS IS NOT RESPONSIBLE, OR LIABLE FOR IMPROPER FUNCTION ATTRIBUTABLE TO STATIC PRESSURE. AIR VOLUME, OR INSTALLATION OTHER THAN THAT INDICATED AND /OR SPECIFIED. DESIGN SPECIFICATION VENTMATIC VENTILATION HOOD MANUFACTURED BY PACIFIC STAINLESS PRODUCTS, INC. 10100 SW ALLEN BLVD., BEAVERTON, OR., 97005 VENTMATIC HOOD SYSTEMS ARE FABRICATED FROM STAINLESS STEEL WHERE EXPOSED, EXTERNAL SEAMS ARE WELDED LIQUID TIGHT AND ALL EXPOSED SURFACE WILL BE POLISHED TO A #4 FINISH. THE VENTILATION HOODS ARE BUILT IN COMPLIANCE WITH NFPA STANDARD #96, ! U.L. CLASSIFIED, AND IS NSF APPROVED, THE HOOD WILL HAVE A FULL LENGTH SEMI - CONCEALED GREASE TRACK THAT WILL PITCH TO A REMOVABLE GREASE COLLECTOR. GREASE EXTRACTORS TO BE U.L. CLASSIFIED BAFFLE TYPE FILTERS MOUNTED AT NO LESS THAN A 45 DEG. ANGLE AND WILL BE LOCKED IN PLACE DURING NORMAL OPERATION BY MEANS OF AN UPPER HOLDING TRACK AT THE TOP OF THE FILTER. THE HOOD WILL BE EQUIPPED WITH U.L. LISTED LIGHT FIXTURES SUITABLE FOR 100 WATT INCANDESCENT BULBS WITH PLASTIC COATED GLASS BULB AND WILL BE PRE -WIRED TO A SINGLE CONNECTION POINT. ETL Listed, NFPA Sc NSF Ventmatic Installation Manual Hood CFM: Low Temp Equipment Mid Temp Equipment High Temp Equipment or Smoke Producing Minimum CFM Moximum CFM 260 CFM 0 Linear Ft. 280 CFM 0 Linear Fl. 300 CFM 0 Linear Ft. 260 CFM o Linear Ft. 350 CFM 0 linear Ft. Greose extraction filters to be oluminum or stainless steel. Hood fights to be connected to separate woll switch. Access for wiring locoted on top. Exhoust fon to be connected to separate power source and interlocked to supply air fan. Meg starter heaters and circuit breaker to be sized to motor ampocity. Clearances from combustible material: Top 18" Side 18' Front 18 Bock 18' The obove clearances con be reduced to 3' if one hour material is used for surrounding material. Hood should be hung from troll frame and front hungers suppled with hood. Front hanger rod to be not less than 3/8' inch all thread. with double nuts at both ends. Bock hanger to be not less than 110 x 1 1/2.. sheet metal screw, 24' on center and lock weld to stainless steel wall frame. Refer to detail drawing No. 1. The exhaust hood must be hung level in order for grease to properly drain. Roof and ceiling supports to be odequote to support hood weight. Verify hood overhang. height and exact location with approved Job site drawings Exhoust hoods with fire dampers in the exhaust of makeup air -duct collars require access for maintenance and inspection. Exhaust outlet to be connected to approved grease duct. Connection to be continuous welded joint. Makeup air inlet to be connected to approved Uniform Mechanical Code Standard for metal, fiberboard and flexible duct. Insulation required on at ducting on system milt tempered dr. Tempered dr recommended on system exceed/rig 2000 CFI". and area where outdoor temperatures drop below 45 degrees F. All exhaust tons, supply fans. curbs, exhaust ducts, molceup air -duct. hood enclosure panels, etc., must be installed to the latest elation of NFPA 96, and the recognized building code where the exhaust hood is being installed. VENTH F11C ELECTRICAL JUNCTION 130X (VERIFY LOCATION) ETL LISTED FILE *2001066 VENTMATIC EXH. HOOD THE EXHAUST VENTILATOR CONFORMS TO U.LSTANCARD -710 'EXHAUST HOODS FOR COMMERCIAL COOKING EQUIPMENT'. g6 BY PACIFIC STAINLESS PRODUCTS INC. FLUTED STYLES 'STANDARD' (FLUTING 6' a or - O.CJ HOOD MODEL: CDW - 132 59 (VERIFY LOCATION) 16' MAXIMUM — FRONT TO BACK EXHAUST DUCT AREA • LIGHTS AND ACCESSORIES CONDUITS LOCATED OUTSIDE 7 --OF WOOD TOP PANEL AREA HOOD LIGHTS 14 A FLAN VIEW 14 16 11/4 i ELEVATION VIEW EXHAUST DUCT COLLAR ALL -THREAD HANGER BRACKET TYP. (4x) t3 13/0 1 3/8 i 3' WOOD WALL 1 7-- FRAME C 1 FIXED SizACKET DETAIL- 16 1\ 1 0 6 ,2 ” SECTION VIEW EXHAUST DUCT COLLAR f 4 L.v. 5/5 BAFFLE FILTER WALL FRAME S/S GREASE CUP REV leap fOR A v:11 IAN 2 41 '� k "---Oty O tit3ltia BMW* ONIcION i CODE COMPLIA t ^Rir =T':: ef OLt;14 ?OC' CUSTOMER APPROVAL FOR MANUFACTURE APPROVED AS NOTED APPROVED WITHOUT EXCEPTION REVISE MD RESUBMIT SIGNATURE O O 0 NAME DATE • aF to O U) O to C 0 I O O O V C Stainless Products, /SW Allen Blvd. c17005 Tel. HOOD ITEM NUMBER A HOOD LENGTH (IN.) B HOOD WIDTH (IN.) C HOOD HEIGHT (IN.) HOOD WT. (LBS.) TOTAL HOOD EXHAUST (CFM) EXHAUST COLLAR SIZE (IN.) DUCT COLLAR VELOCITY (FPM) TOTAL COLLAR STATIC PRESSURE LIGHT FIXTURE QUANTITY LIGHT VOLTAGE WATfS/ PHASE VH5 42 42 20 109 613 8 1756 .25 s 1a2- 44 11)2 c s n - 15,01 ' ll y F324u I 3 4 iI IS. ij 1 � a h Pacific Stainless REVISION: 0 SCALE: NOTED CHECKED: D. S. Zi7g171700 :ON SOt' DRAWN BY: 1,121 -4 9/L./ ZI :31da 70&e7 i TYPE 2 HOOD NOTES mia 1. HOOD TO BE 18 GA. S /S. ALL- WELDED CONSTRUCTION WITH ALL JOINTS AND SEAMS TO BE GROUND SMOOTH. 2. DUCTING TO BE 24GA. GALVANIZED NON-WELDED DUCTWORK. 3. THE GENERAL CONTRACTOR SHALL PROVIDE AND INSTALL ALL PENETRATIONS. SHAFTS. RAIN SHIELDS AND SEAL WEATHER TIGHT. 4. EXHAUST DUCTS SHALL SLOPE TOWARD HOOD 1/4" PER 12" OF LINEAL LENGTH. 5. THE EXHAUST AND MAKEUP AIR SYSTEMS SHALL BE CONNECTED BY AN ELECTRICAL INTERLOCKING SWITCH. (ALL ELECTRICAL BY ELECTRICAL CONTRACTOR - REFER TO ELECTRICAL DRAWINGS). 6. EXHAUST HOOD AND LIGHT FIXTURES TO BE UL LISTED. 7. CONSTRUCTION OF EXHAUST SYSTEMS HOODS AND DUCTS TO CONFORM TO 'UMC' CODE. 8. THE ELECTRICAL CONTRACTOR SHALL MAKE ALL APPLICABLE CONNECTIONS FOR PROPER OPERATION OF ALL SYSTEMS. 9. THE GENERAL CONTRACTOR SHALL VERIFY ALL DIMENSIONS BEFORE CONSTRUCTION OF PENETRATIONS AND COORDINATE CRITICAL EXHAUST SYSTEM REQUIREMENTS WITH ( P.S.P.) 10. THE ELECTRICAL CONTRACTOR SHALL LOCATE ALL ELECTRICAL CONNECTIONS FOR EACH FAN MOTOR AT EACH FAN LOCATION. 11. THE ELECTRICAL CONTRACTOR SHALL SUPPLY ALL THERMAL DISCONNECTS AND MAG STARTERS. 12. THE EXHAUST AND MAKE UP AIR SYSTEM IS COVERED BY A ONE YEAR PARTS AND LABOR WARRANTY FROM THE DATE OF EQUIPMENT START UP. PROVIDED A QUALIFIED SERVICE COMPANY IS PERFORMING REGULAR MAINTENANCE. THIS WARRANTY IS VOID IF NO SERVICE HAS BEEN PERFORMED AFTER NINETY (90) DAYS FROM THE EQUIP. START UP DATE. 21 VERIFY HOOD MODEL: PSP - 'C' 42 BY PACIFIC STAINLESS PRODUCTS INC. 21 (VERIFY)-7 8'dta PLAN VIEW ALL - THREAD HANGER BRACKET TYP? (2x) A GUTTER DRAIN AREA 1 3/S ELEVATION VIEW / — EXHAUST DUCT COLLAR 1 3/S 42' X 42' X 20' I-IIGl-1� 18 GA 5/5 TYPE II VAPOR EXHAUST LL HOOD BY PSP_ 21`71` 1 3/8 FIXED 61RACKET DETAIL 5!5 DRIP GUARD BAFFLE SECTION VIEW 1 REVIEWED FOR CODE COMPLIANCE ty Of Tukwila BUILDING DNTcTnN EXHAUST VAPOR DUCT COLLAR GUTTER DRAW 1W Yr DIA. TUBING TO BE COI+ ECTED BY &C. JAN 2 4 P i II o:J aj Eb 011; 1 4 r CUSTOMER APPROVAL FOR MANUFACTURE APPROVED AS NOTED APPROVED WITHOUT EXCEPTION REVISE MID RESUBMIT SICIU1URE 0 0 0 NAME DATE • d0 0 m IL 0 Tn N 1- 4 I 0 0 N I 0 ID I V C v a t (503) 646-2348 *44* MONROE, Stainless Products, 10100 /S1A1 Allen Blvd. 7G14-770c1 -