HomeMy WebLinkAboutPermit M08-016 - AMERICAN FAMILY INSURANCEAMERICAN FAMILY INS
13038 INTERURBAN AV S
#120
M08-016
Parcel No.: 0003000110
Address:
Suite No:
Tenant:
Name:
Address:
Owner:
Name:
Address:
Contact Person:
Name: MICHAEL AROMIN
Address: PO BOX 1581 , AUBURN WA
Value of Mechanical: $3,000.00
Type of Fire Protection:
Furnace: <100K BTU
>100K BTU
Floor Furnace
Suspended/Wall/Floor Mounted Heater
Appliance Vent
Repair or Addition to Heat/Refrig /Cooling System....
Air Handling Unit <10,000 CFM
>10,000 CFM
Evaporator Cooler
Ventilation Fan connected to single duct
Ventilation System
Hood and Duct
Incinerator: Domestic
Commercial/Industrial
doc: IMC -10/06
CitAbf Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 - 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
13038 INTERURBAN AV S TUKW
AMERICAN FAMILY INSURANCE
13038 INTERURBAN AV S #120 , TUKWILA WA
INTERURBAN 13038 LLC
4616 25TH AVE NE PMB 746 , SEATTLE WA
Contractor:
Name: NORTH MECHANICAL SHEET METAL INC
Address: PO BOX 1581 , AUBURN WA
Contractor License No: NOMECSM975C7
MECHANICAL PERMIT
DESCRIPTION OF WORK:
HVAC DUCTWORK ONLY, SUPPLY AND RETURN DIFFUSERS FROM EXISTING ROOFTOP UNIT
EOUIPMENT TYPE AND OUANTITY
0
0
0
0
0
0
0
0
0
0
0
0
0
0
* *continued on next page **
M08 -016
Permit Number:
Issue Date:
Permit Expires On:
Phone:
Phone: 253 -735 -1825
Phone: 253 - 735 -1825
Expiration Date: 02/27/2009
M08 -016
01/23/2008
07/21/2008
Fees Collected: $191.18
International Mechanical Code Edition: 2006
Boiler Compressor:
0 -3 HP /100,000 BTU 0
3 -15 HP /500,000 BTU 0
15 -30 HP /1,000,000 BTU.. 0
30 -50 HP /1,750,000 BTU.. 0
50+ HP /1,750,000 BTU 0
Fire Damper 0
Diffuser 11
Thermostat 0
Wood/Gas Stove 0
Water Heater 0
Emergency Generator 0
Other Mechanical Equipment
Printed: 01 -23 -2008
Permit Center Authorized Signature:
Signature:
doc: IMC -10/06
•
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 -431 -3670
Fax: 206 - 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
I hereby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances
governing this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating
construction or t ce am authorized to sign and obtain this mechanical permit.
Permit Number: MO8 -016
Issue Date: 01/23/2008
Permit Expires On: 07/21/2008
Date: I =3 V T}
Date: 1 — z3-f7
Print Name: nil ('0Z— i �/1G.r-r f/✓
This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended
or abandoned for a period of 180 days from the last inspection.
M08 -016 Printed: 01 -23 -2008
Parcel No.: 0003000110
Address:
Suite No:
Tenant:
•
City of Tukwila
13038 INTERURBAN AV S TUKW
AMERICAN FAMILY INSURANCE
1: ** *BUILDING DEPARTMENT CONDITIONS * **
doc: Cond -10/06
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 - 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
PERMIT CONDITIONS
* * continued on next page **
Permit Number:
Status:
Applied Date:
Issue Date:
M08 -016
ISSUED
01/16/2008
01/23/2008
2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the
Building Official.
3: All mechanical work shall be inspected and approved under a separate permit issued by the City of Tukwila Permit Center
(206/431- 3670).
4: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to
start of arty construction. These documents shall be maintained and made available until final inspection approval is
granted.
5: All construction shall be done in conformance with the approved plans and the requirements of the International
Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code.
6: Remove all demolition rubble and loose miscellaneous material from lot or parcel of ground, properly cap the sanitary
sewer connections, and properly fill or otherwise protect all basements, cellars, septic tanks, wells, and other
excavations. Final inspection approval will be determined by the building inspector based on satisfactory completion of
this requirement.
7: Manufacturers installation instructions shall be available on the job site at the time of inspection.
8: All electrical work shall be inspected and approved under a separate permit issued by the City of Tukwila Building
Department (206- 431- 3670).
9: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of,
any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits
presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila
shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the
Building Official from requiring the correction of errors in the construction documents and other data.
M08 -016 Printed: 01 -23 -2008
I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and ordinances governing
this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provision of any other work or local laws regulating
construction or the performance of work.
Signature:
Print Name:
doc: Cond -10/06
•
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 -431 -3670
Fax: 206 - 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
/1 /L'/ t z. /? ,, } /A/
Date: 1 d
M08 -016 Printed: 01 -23 -2008
CITY OF TUKWILir
Community Development Department
Permit Center
6300 Southcenter Blvd., Suite 100
Tukwila, WA 98188
http://www.ci.tukwila.wa.us
MECHANICAL PERMIT APPLICATION
Applications and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or by fax.
* *Please Print **
SITE LOCATION
Q King Co Assessor's Tax No.:
Site Address: 13o 3 U I IVTGELA4t3Au Ave S4 ,
Tenant Name: L - �2 /� .r4tt,� f'*m 1 i--r 1 A.,/5 viz
New Tenant: .... Yes El ..No
Property Owners Name: L .41 O Z d (- e5-1_ (,S 3S
Mailing Address: 1( ZS lU, S e WAS/4 `7 610s
Name: M 4 -2.vYi4 t AJ
Mailing Address:
E -Mail Address:
Po & X lS 'l
City
Company Name: tOd t n? - - (/4'i(J1 e-4 (I{ E? - r /h L - -Z._
Mailing Address: 1 a ft4l A) A086/2-4)
E -Mail Address:
Contractor Registration Number: AJ0/ EGSj"1'7 e-7
Contact Person:
E -Mail Address:
Q: Applications\Forms- Applications On Line \3-2006 - Mechanical Permit Application.doc
Revised: 4 -2006
bh
Mechanical Permit No.
6GO3600//0
Suite Number: ( ZC' Floor:
WASH
State Zip
CONTACT PERSON - who do we contact when your permit is ready to be issued
Day Telephone: ZS3 -'73 S -/ SZS
A ell3 vr-A) G114 S/-4 r'1 f30
City State Zip
Fax Number: ZS3 -7 3S- IS Z 5
MECHANICAL CONTRACTOR INFORMATION -
Expiration Date: - 2 -7 - 2-
?gro2-
City State Zip
Contact Person: M t&/- 114 - eq-. P. ,Ae-ant 1 Day Telephone: 2S -- 3s - 41S aL #
Fax Number: 2-S3 -- '73 S = / 62s
ARCHITECT OF RECORD - All plans must be wet stamped byArchitee
Record
Company Name:
Mailing Address:
Zip
Contact Person:
E -Mail Address:
City
Day Telephone:
Fax Number:
State
ENGINEER OF RECORD - All .plans must be wet stamped by Engineer of Record
Company Name:
Mailing Address:
City
Day Telephone:
Fax Number:
State
Zip
Page 1 of 2
Unit Type:
Qty
Unit Type:
Qty
Unit Type:
Qty
Boiler /Compressor:
Qty
Furnace <100K BTU
Air Handling Unit >10,000
CFM
Fire Damper
0 -3 HP /100,000 BTU
Furnace >100K BTU
Evaporator Cooler
Diffuser
/ /
3 -15 HP /500,000 BTU
Floor Furnace
Ventilation Fan Connected
to Single Duct
Thermostat
15 -30 HP /1,000,000 BTU
Suspended /Wall/Floor
Mounted Heater
Ventilation System
Wood /Gas Stove
30 -50 HP /1,750,000 BTU
Appliance Vent
Hood and Duct
Water Heater
50+ HP /1,750,000 BTU
Repair or Addition to
Heat/Refrig /Cooling
System
Incinerator - Domestic
Emergency
Generator
Air Handling Unit
<10,000 CFM
Incinerator — Comm /Ind
Other Mechanical
Equipment
Date Application Accepted:
( / f�
1— I W o 1>
Date Application Expires
- 7- I^ . cris
Staff Initials:
uu ,ic.„
I
Valuation of Project (contractor's bid price): $ 3000, O 0
Scope of Work (please provide detailed information): W (JA C° D Oar l0/2- CJAlL- -
sv °PL'Y 4440 FLE Ttiry s � C?2rc c S
Use: Residential: New .... Replacement ....
Commercial: New ... Replacement ....
Fuel Type: Electric ❑ Gas ....J Other: 7k1 S7? it/4 �-a jP 1/144-e_ /`' T
Indicate type of mechanical work being installed and the quantity below:
PERMIT APPLICATION NOTES — Applicable to all permits ir.
Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject
to possible revision by the Permit Center to comply with current fee schedules.
Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation.
The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be requested
in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition).
I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO 13E TRUE UNDER
PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT.
BUILDING OW ► :rl; e A - r ' IZED AGENT:
Signature: / �
/
Print Name: /I/ ,2/J /' 4 74/
Mailing Address: /3.5 4/
Q \Applications\Forms- Applications On Line \3 -2006 - Mechanical Permit Application.doc
Revised: 4 -2006
bh
Date: 1 " Y-658
Day Telephone: Z 3-5e)
/ '/3c//�c/ Ge/ -/ 98 Z
City State Zip
Page 2 of 2
Parcel No.: 0003000110 Permit Number: M08 -016
Address: 13038 INTERURBAN AV S TUKW Status: PENDING
Suite No: Applied Date: 01/16/2008
Applicant: AMERICAN FAMILY INSURANCE Issue Date:
Receipt No.: R08 -00131
Initials: WER
User ID: 1655
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 -431 -3670
Fax: 206 -431 -3665
Web site: http: / /www.ci.tukwila.wa.us
Payee: NORTH MECHAINICAL SHEET METAL
TRANSACTION LIST:
Type Method Description Amount
Payment Check 5955 191.18
ACCOUNT ITEM LIST:
Description
MECHANICAL - NONRES
PLAN CHECK - NONRES
Account Code Current Pmts
000/322.100
000/345.830
RECEIPT
Total: $191.18
Payment Amount: $191.18
Payment Date: 01/16/2008 10:33 AM
Balance: $0.00
158.94
32.24
7318 01/16 9710 TOTAL 191.18
doc: Receiot -06 Printed: 01 -16 -2008
Project:
�- 0-- 4._ tom`
�.. 1 y
of
Type Inspecti • n:
k ,. KJ Me4
Address:
Date Called:
Special Instructions:
Date Wanted: /
3 -I3-o& •
c a, m...
p.m.
Requester:
Phone No:
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO. PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3 7
Approved per applicable codes. Corrections required prior to approval.
COMMENTS:
,A,& .(L A,L 6A-(
Inspe 6r:
Date � j 3
ov1/4-/k. AAJ/
J $58.00 REINSPECTION FEE REWIRED. Prior o inspection, fee must be
paid at 6300 Southcenter Blvd., Buite 100. Call the schedule reinspection.
Receipt No.:
'Date:
Project: ff
AAA CI, LA rsk ! 1 (. ,r
Type of Inspection:
I v 4 k\ T-A.)
t
C ,
Address:
13 o 3g Thurtruin Ad
Date Called:
Special Instructions:
7 ,....
Date Wanted:
2 -
mo t)(\
y am
``,
p.
Requester:
Phone No: 3 _3S6 I4
1
INSPECTION RECORD
Retain a copy with permit
PERMIT NO.
INSPECTION NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -36
Approved per applicable codes. El Corrections required prior to approval.
COMMENTS:
Insptor:\
Date:
2
❑ $58.00 REINSPECTION FEE REQUIRED. Prior o inspection. fee must be
paid at 6300 Southcenter Blvd.. Suite 100. Call the schedule reinspection.
Receipt No.:
Date:
:ar i 'Ries '4., �i.ltit•d..:�.....� ._ ;�> ..�:1 "•?' .i- A �. '.:+R��tir .�':�'.' �:''.1'... �:. :!: •. a'�,w'aFr, ¢
COMMENTS:
T of Ins ection:
Uu 1 t.
C A'f 6 e. r
J( 4- - (f r J: -I e
At./ ' f il r
'`-s e i ..•)
c
(A,. e_,- f 2)
, -\ , )1 00 c-
•
0 .)ta /11 a
9cr f-(cJA c AJa7Ei.
Iktr h4 !
( r P- , A f i oe- - < d1
-4951
Project:
Mite/ OA �" . (
T of Ins ection:
Uu 1 t.
\.
• •
Address:
130 3e n�rul4k4 Auk_.. S
Date Call d:
,
Special Instructions:
Date Wanted:
? / - d
%A.mw
p.1
Requester:
f
Phone No:
9 5 3 -35
-4951
MO Y-
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO. PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION 9-
6300 Southcenter Blvd., #1 00, Tukwila, WA 98188 (206)431-36
El Approved per applicable codes.
Corrections required prior to approval.
Inspe or.') 0.....0 • k d t 4 .„,..
58.00'REINSPECTION EE
REQUIRED. - r/- Ok"
$ t QUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call the schedule reinspection.
Receipt No.:
Date:
•
Cooling Equipment Schedule
Equip.
ID
Brand Name'
Model No.
Capacity
Btu /h
Total CFM
OSA CFM
or Econo?
SEER
or EER
IPLV
Location
7 •vim
YGs acts-
Woo
/60 a
iea'
/ 357ixi2
6Yaco
RO'ciF
RECEIVED
JAN 1 6 2006
FILE
COPY
'
PERMIT CENTS
m
0 8
.., 0
Fan Equipment Schedule
Equip.
ID
Brand Name'
Model No.'
CFM
SP
HP /BHP
Flow Control
Location of Service
Efficienc °
7774/vE
YGSes' ir
0 WO
/ode)
£ee'vo
Foam)
6Yaco
69
RECEIVED
JAN 1 6 2006
'
PERMIT CENTS
m
0 8
.., 0
Heating Equipment Schedule
Equip.
ID
Brand Name'
Model No.
Capacity
Btu /h
Total CFM
OSA cfm
or Econo?
Input Btuh
Output Btuh
Efficienc °
7774/vE
YGSes' ir
0 WO
/ode)
£ee'vo
Foam)
6Yaco
69
CITY OF TUKWILA - BUILDING DIVISION
2006 Washington State Nonresidential Energy Code Compliance Form
Mechanical Summary
MECH -SUM
2006 Washington State Nonresidential Energy Code Compliance Forms
Revised July 2007
Project Info
Project Description
Briefly describe mechanical
system type and features.
ErsIbigEdes Plans
Project Address /30 36 � „2GomnJ • re,
1/,k-I(l /L/ 4-
Applicant Name: /w .srfiaor
Applicant Address:
130 K`.
5 E �,¢�•v T)
,qv�v w L
Applicant Phone:,,. z_53_735__/6 Z
7 y f,-4 o ua-et
(IXisn -- / PT 1 Gry /r)
Include documentation requiring compliance with commissioning requireme
Date
For Building Dept. Use
IEW FOR
E COMPLIANCE
VE
JAN 1 7 2008
CI Of Tukwila
ts,pr DIVISION
Compliance Option
Simple System Q Complex System 0 Systems Analysis
(See Decision Flowchart (over) for qualifications. Use separate MECH -SUM for simple & complex systems.)
Equipment Schedules
The following information is required to be incorporated with the mechanical equipment schedules on the
plans. For projects without plans, fill in the required information below.
System Description
See Section 1421 for full description of
Simple System qualifications.
If Heating /Cooling csgl Constant vol?
Cooling Only:
• Air cooled? A Packaged sys? • <20,000 Btuh?
Economizer included?
or • Split system?
If Heating Only:
<
■ <5000 cfm?
• <70% outside air?
CITY OF TUKWILA - BUILDING DIVISION
2006 Washington State Nonresidential Energy Code Compliance Form
Mechanical Summary (back)
MECH -SUM
Decision Flowchart
Use this flowchart to determine if project qualifies for Simple System Option. If not, either the
Complex System or Systems Analysis Options must be used.
Simple System
Allowed
(section 1420)
otal Ca .
wo economize
<240,000 Btuh
or 10 %?
Heating Only
No
Yes —
( \
Reference
Section 1421
Heating /Cooling
or Cooling Only
Reference -\
Section 1423
Complex Systems
Refer to MECH -COMP Mechanical Complex Systems for assistance in determining which Complex
Systems requirements are applicable to this project.
Use Complex
Systems
(section 1430)
A
Mechani .I P- ' PI- C - cklist I MECH -CHK
2006 Washington State Nonresidential Energy Code Compliance Forms Revised July 2007
Project Address 1 3 6 3 g / ; Je A' S.
(Date 1 _06
The following information is necessary to check a mechanical permit application for compliance with the mechanical requirements in the
Washington State Nonresidential Energy Code.
Applicability
(yes, no, n.a.)
Code
Section
Component
Information Required
Location
on Plans
Building Department
Notes
HVAC REQUIREMENTS (Sections 1401 -1424)
1411
Equipment performance
(v.--
1411.4
Pkg. elec. htg.& clg.
List heat pumps on schedule
�—
1411.1
Minimum efficiency
Equipment schedule with type, capacity, efficiency
1411.1
Combustion htg.
Indicate intermittent ignition, flue /draft damper & jacket loss
1412
HVAC controls
1.-----
1412.1
Temperature zones
Indicate locations on plans
1412.2
Deadband control
Indicate 5 degree deadband minimum
1412.3
Humidity control
Indicate humidistat
1412.4
Automatic setback
Indicate thermostat with night setback and 7 diff. day types
1412.4.1
Dampers
Indicate damper location and auto. controls & max. leakage
1412.4.2
Optimum Start
Indicate optimum start controls
1412.5
Heat pump control
Indicate microprocessor on thermostat schedule
1412.6
Combustion htg.
Indicate modulating or staged control
1412.7
Balancing
Indicate balancing features on plans
1412.8
Ventilation Control
Indicate demand control ventilation for high- occupancy areas
1422
Thermostat interlock
Indicate thermostat interlock on plans
1/
1423
Economizers
Equipment schedule
1413
Air economizers
f/
1413.1
Air Econo Operation
Indicate 100% capability on schedule
1413.1
Wtr Econo Operation
Indicate 100% capacity at 45 degF db & 40 deg F wb
1413.2
Water Econo Doc
Indicate clg load & water econoe & clg tower performance
1413.3
Integrated operation
Indicate capability for partial cooling
1413.4
Humidification Indicate direct evap or fog atomization w/ air economizer
1414
Ducting systems
t/
1414.1
Duct sealing
Indicate sealing necessary
✓
1414.2
Duct insulation
Indicate R -value of insulation on duct
1415.1
Piping insulation
Indicate R -value of insulation on piping
1416
Completion Requirements
1416.2.1
Commissioning
Provide commissioning plan
1416.2.2 -3
Sys.Bal & Func.Test
Indicate air and water system balancing & functional testing
1416.2.4
Commissioning
Indicate O &M manuals, record drawings, staff training
1416.2.5
Comm. Report
Indicate requirements for prelim. & final commissioning report
1434
Separate air sys.
Indicate separate systems on plans
Mechanical
Summary Form
Completed and attached. Equipment schedule with types,
input/output, efficiency, cfm, hp, economizer
SERVICE WATER HEATING AND HEATED POOLS (Sections 1440 - 1454)
1440
Service water htg.
1441
Elec. water heater
Indicate R -10 insulation under tank
1442
Shut -off controls
Indicate automatic shut -off
1443
Pipe Insulation
Indicate R -value of insulation on piping
1452
Heat Pump COP
Indicate minimum COP of 4.0
1452
Heater Efficiency
Indicate pool heater efficiency
1453
Pool heater controls
Indicate switch and 65 degree control
2006 Washington State Nonresidential Energy Code Compliance Form
2006 Washin • ton State Nonresidential Ener• Code Corn • Iiance Form
Mechanical Perrnot Plans Checklist
2008 Washington, State Nonresidential Energy CodeCompliarice Farms
�ECHCI�K
Revised July 2007
Mechanical - General Requirements
1411.1 General: Equipment shall have a minimum performance at the specified
rating conditions not less than the values shown in Table 14 -1A through 14 -1G. If a
nationally recognized certification program exists for a produ ct covered in Tables
14 -1A through 14 -1G, and it includes provisions for verification and challenge of
equipment efficiency ratings, then the product shall be listed in the certification
program.
Gas -fired and oil -fired forced air fumaces with input ratings > 225,000 Btu/h (65
kW) and all unit heaters shall also have an intermittent ignition or interrupted device
(IID), and have either mechanical draft (including power venting) or a flue damper. A
vent damper is an acceptable altemative to a flue damper for furnaces where
combustion air is drawn from the conditioned space. All fumaces with input ratings >
225,000 Btu/h (65 kW), including electric fumaces, that are not located within the
conditioned space shall have jacket losses not exceeding 0.75% of the input rating.
1411.2 Rating Conditions: Cooling equipment shall be rated at ARI test conditions
and procedures when available. Where no applicable procedures exist, data shall
be furnished by the equipment manufacturer.
1411.3 Combination Space and Sery ice Water Heating: For combination space
and service water heaters with a principal function of providing space heat, the
Combined Annual Efficiency (CAE) may be calculated by using ASHRAE Standard
124 -1991. Storage water heaters used in combination space heat and water heat
applications shall have either an Energy FActor (EF) or a CAE of not less than the
following:
1411.4 Packag
equipment providing both heating and cooling with a total cooling capacity greater
than 20, Btu/h shall be a heat pump.
Exception: Unstaffed equipment shaelters or cabinets used solely for
personal wireless service facilities.
1412 Controls
1412.1 Temperature Controls: Each system shall be provided with at least one
temperature control device. Each zone shall be controlled by individual thermostatic
controls responding to temperature within the zone. At a minimum, each floor of a
building shall be considered as a separate zone.
1412.2 Deadband Controls: When used to control both comfort heating and
cooling, zone thermostatic controls shall be capable of a deadband of at least 5
degrees F within which the supply of heating and co offing energy to the zone is shut
off or reduced to a minimum.
Exceptions:
1. Special occupancy, special usage, or code requirements where
deadband controls are not appropriate.
2. Buildings complying with Section 1141.4, if in the proposed building
energy analysis, heating and cooling thermostat setpoints are set to
the same temperature between 70 degrees F and 75 degrees F
inclusive, and assumed to be constant throughout the year.
3. Thermostats that require manual changeover between heating and
cooling modes.
1412.3 Humidity Controls: If a system is equipped with a means for adding
moisture, a humidistat shall be provided.
1412.4 Setback and Shut -Off: HVAC systems shall be equipped with automatic
controls capable of accomplishing a reduction of energy use through control setback
or equipment shutdown during periods of non -use or alternate use of the spaces
served by the system. The automatic controls shall have a minimum seven -day
clock and be capable of being set for seven different day types per week. It must
retain programming and time for a power loss of 10 hours and include an accessible
manual override of up to 2 hours.
Exceptions:
1. Systems serving areas which require continuous operation at the
same temperature setpoint.
2. Equipment with full loa d demands of 2 kW (6,826 Btu/h) or less may
be controlled by readily accessible manual off-hour controls.
3. Systems controlled by an occupant sensor that is capable of shutting
the system off when no occupant is sensed for a period of up to 30
minutes.
4. Systems controlled solely by a manually operated timer capable of
operating the system for no more than two hours.
1412.4.1 Dampers: Outside air intakes, exhaust outlets and relief outlets serving
conditioned spaces shall be equipped with dampers which close au tomatically when
the system is off or upon power failure. Stair shaft and elevator shaft smoke relief
openings shall be equipped with normally open (fails to open upon loss of power)
dampers. These dampers shall remain closed until activated by the fire a larm
system or other approved smoke detection system.
Exceptions:
1. Systems serving areas which require continuous operation,
2. Combustion air intakes.
3. Gravity (nonmotorized) dampers are acceptable in buildings Tess
than 3 stories in height.
1412.6 ventilation t:ontrois for High - Occupancy Areas: 1Tcsmandcontrol
ventilation (DCV) is required for spaces that are larger than 500 ft2, have a design
occupancy for ventilation of greater than 40 people for 1000 ft2 of floor area, and are
served by systems with one or more of the following:
a. An air -side economizer,
b. Automatic modulating control of the outdoor air damper, or
c. A design outdoor airflow greater than 3000 cfm.
Exceptions:
1.Systems with energy recovery complying with Section 1436.
2. Multiple -zone systems without direct - digital control of individual zones
communicating with a central control panel.
3. Systems with a design outdoor airflow less than 1200 cfm.
4. Spaces where the supply airflow rate minus any makeup or outgoing
transfer air requirement is less than 1200 cfm.
1413 Air Economizers
1413.1 Operation: Air economizers shall be of automatically modulating outside and
retum air dampers to provide 100 percent of the design supply air as outside air to
reduce or eliminate the need for meth anical cooling. Water economizers shall be
capable of providing the total concurrent cooling load served by the conneted
terminal equipment lacking airside economizer, at outside air temperatures of 45 ° F
dry- bulb /40 ° F wet -bulb and below. For this calculati on, all factors including solar and
intemal load shall be the same as those used for peak load calculations, except for
the outside temperatures.
Exception: Water economizers using air - cooled heat rejection equipment
may use a 35 ° F dry-bulb outside air to mperature for this calculation. This
exception is limited to a maximum of 20 tons per building.
1413.2 Documentation: Water economizer plans submitted for approval shall
include the following information:
1. Maximum outside air conditions for which economizer is sized to provide
full cooling.
2. Design cooling load to be provided by economizer at this outside air
condition.
3. Heat rejection and terminal equipment performance data including model
number, flow rate, capacity, entering and leaving temperature in full
economizer cooling mode.
1413.3 integrated Operation: Air economizers shall be capable of providing partial
cooling even when additional mechanical cooling is required to meet the remainder
of the cooling load.
Exceptions:
1. Individual, direct expansion units that have a rated capacity less than
65,000 Btu/h and use nonintegrated economizer controls that
preclude simultaneous operation of the economizer and mechanical
cooling.
2. Water - cooled water chillers with w aterside economizer.
1413.4 Humidification: If an air economizer is required on a cooling system for
which humidification equipment to be provided to maintain minimum indoor
humidity levels, then the humidifier shall be of the adiabatic type (direct evaporative
media or fog atomization type).
Exceptions:
1. Health care facilities where WAC 246 - 320 -525 allows only steam
injection humidifiers in ductwork downstream of final filters. 1412.6
Combustion Heating Equipment Controls: Combustion heating
equipment with a capacity over 225,000 Btu /h shall have modulating
or staged combustion control.
2. Systems with water economizer
3. 100% outside air systems with no provisions for air recirculation to the
central supply fan.
4. Nonadiabatic humidifiers cumulatively serving no more than 10% of a
building's air economizer capacity as measured in cfm. This refers to
the system cfm serving rooms with stand alone or duct mounted
humidifiers.
1414 Ducting Systems
1414.1 Sealing: Duct work which is designed to operate at pressures above 1/2 inch
water column static pressure shall be sealed in accordance with Standard RS- 18.
Extent of sealing required is as follows:
1. Static pressure: 1/2 inch to 2 inches; seal transverse joints.
2. Static pressure: 2 inches to 3 inches; seal all transverse joints and
longitudinal seams.
3. Static pressure: above 3 inches; seal all transverse joints, longitudinal
seams and duct wall penetrations.
Duct tape and other pressure sensitive tape shall not be used as the primary
sealant where ducts are designed to operate at stati c pressures of 1 inch W.C. or
greater.
1414.2 Insulation: Ducts and plenums that are constructed and function as part of
the building envelope, by separating interior space from exterior space, shall meet all
applicable requirements of Chapter 13. These re quirements include insulation
installation, moisture control, air leakage, and building envelope insulation levels.
Unheated equipment rooms with combustion air louvers must be isolated from the
conditioned space by insulating interior surfaces to a minimu m of R -11 and any
exterior envelope surfaces per Chapter 13. Outside air ducts serving individual
supply air units with less than 2,800 cfm of total supply air capacity shall be insulated
EF
CAE
< 50 gal storage
0.58
0.71
50 to 70 gal storage
0.57
0.71
> 70 gal storage
0.55
0.70
2006 Washin • ton State Nonresidential Ener• Code Corn • Iiance Form
Mechanical Perrnot Plans Checklist
2008 Washington, State Nonresidential Energy CodeCompliarice Farms
�ECHCI�K
Revised July 2007
Mechanical - General Requirements
1411.1 General: Equipment shall have a minimum performance at the specified
rating conditions not less than the values shown in Table 14 -1A through 14 -1G. If a
nationally recognized certification program exists for a produ ct covered in Tables
14 -1A through 14 -1G, and it includes provisions for verification and challenge of
equipment efficiency ratings, then the product shall be listed in the certification
program.
Gas -fired and oil -fired forced air fumaces with input ratings > 225,000 Btu/h (65
kW) and all unit heaters shall also have an intermittent ignition or interrupted device
(IID), and have either mechanical draft (including power venting) or a flue damper. A
vent damper is an acceptable altemative to a flue damper for furnaces where
combustion air is drawn from the conditioned space. All fumaces with input ratings >
225,000 Btu/h (65 kW), including electric fumaces, that are not located within the
conditioned space shall have jacket losses not exceeding 0.75% of the input rating.
1411.2 Rating Conditions: Cooling equipment shall be rated at ARI test conditions
and procedures when available. Where no applicable procedures exist, data shall
be furnished by the equipment manufacturer.
1411.3 Combination Space and Sery ice Water Heating: For combination space
and service water heaters with a principal function of providing space heat, the
Combined Annual Efficiency (CAE) may be calculated by using ASHRAE Standard
124 -1991. Storage water heaters used in combination space heat and water heat
applications shall have either an Energy FActor (EF) or a CAE of not less than the
following:
1411.4 Packag
equipment providing both heating and cooling with a total cooling capacity greater
than 20, Btu/h shall be a heat pump.
Exception: Unstaffed equipment shaelters or cabinets used solely for
personal wireless service facilities.
1412 Controls
1412.1 Temperature Controls: Each system shall be provided with at least one
temperature control device. Each zone shall be controlled by individual thermostatic
controls responding to temperature within the zone. At a minimum, each floor of a
building shall be considered as a separate zone.
1412.2 Deadband Controls: When used to control both comfort heating and
cooling, zone thermostatic controls shall be capable of a deadband of at least 5
degrees F within which the supply of heating and co offing energy to the zone is shut
off or reduced to a minimum.
Exceptions:
1. Special occupancy, special usage, or code requirements where
deadband controls are not appropriate.
2. Buildings complying with Section 1141.4, if in the proposed building
energy analysis, heating and cooling thermostat setpoints are set to
the same temperature between 70 degrees F and 75 degrees F
inclusive, and assumed to be constant throughout the year.
3. Thermostats that require manual changeover between heating and
cooling modes.
1412.3 Humidity Controls: If a system is equipped with a means for adding
moisture, a humidistat shall be provided.
1412.4 Setback and Shut -Off: HVAC systems shall be equipped with automatic
controls capable of accomplishing a reduction of energy use through control setback
or equipment shutdown during periods of non -use or alternate use of the spaces
served by the system. The automatic controls shall have a minimum seven -day
clock and be capable of being set for seven different day types per week. It must
retain programming and time for a power loss of 10 hours and include an accessible
manual override of up to 2 hours.
Exceptions:
1. Systems serving areas which require continuous operation at the
same temperature setpoint.
2. Equipment with full loa d demands of 2 kW (6,826 Btu/h) or less may
be controlled by readily accessible manual off-hour controls.
3. Systems controlled by an occupant sensor that is capable of shutting
the system off when no occupant is sensed for a period of up to 30
minutes.
4. Systems controlled solely by a manually operated timer capable of
operating the system for no more than two hours.
1412.4.1 Dampers: Outside air intakes, exhaust outlets and relief outlets serving
conditioned spaces shall be equipped with dampers which close au tomatically when
the system is off or upon power failure. Stair shaft and elevator shaft smoke relief
openings shall be equipped with normally open (fails to open upon loss of power)
dampers. These dampers shall remain closed until activated by the fire a larm
system or other approved smoke detection system.
Exceptions:
1. Systems serving areas which require continuous operation,
2. Combustion air intakes.
3. Gravity (nonmotorized) dampers are acceptable in buildings Tess
than 3 stories in height.
1412.6 ventilation t:ontrois for High - Occupancy Areas: 1Tcsmandcontrol
ventilation (DCV) is required for spaces that are larger than 500 ft2, have a design
occupancy for ventilation of greater than 40 people for 1000 ft2 of floor area, and are
served by systems with one or more of the following:
a. An air -side economizer,
b. Automatic modulating control of the outdoor air damper, or
c. A design outdoor airflow greater than 3000 cfm.
Exceptions:
1.Systems with energy recovery complying with Section 1436.
2. Multiple -zone systems without direct - digital control of individual zones
communicating with a central control panel.
3. Systems with a design outdoor airflow less than 1200 cfm.
4. Spaces where the supply airflow rate minus any makeup or outgoing
transfer air requirement is less than 1200 cfm.
1413 Air Economizers
1413.1 Operation: Air economizers shall be of automatically modulating outside and
retum air dampers to provide 100 percent of the design supply air as outside air to
reduce or eliminate the need for meth anical cooling. Water economizers shall be
capable of providing the total concurrent cooling load served by the conneted
terminal equipment lacking airside economizer, at outside air temperatures of 45 ° F
dry- bulb /40 ° F wet -bulb and below. For this calculati on, all factors including solar and
intemal load shall be the same as those used for peak load calculations, except for
the outside temperatures.
Exception: Water economizers using air - cooled heat rejection equipment
may use a 35 ° F dry-bulb outside air to mperature for this calculation. This
exception is limited to a maximum of 20 tons per building.
1413.2 Documentation: Water economizer plans submitted for approval shall
include the following information:
1. Maximum outside air conditions for which economizer is sized to provide
full cooling.
2. Design cooling load to be provided by economizer at this outside air
condition.
3. Heat rejection and terminal equipment performance data including model
number, flow rate, capacity, entering and leaving temperature in full
economizer cooling mode.
1413.3 integrated Operation: Air economizers shall be capable of providing partial
cooling even when additional mechanical cooling is required to meet the remainder
of the cooling load.
Exceptions:
1. Individual, direct expansion units that have a rated capacity less than
65,000 Btu/h and use nonintegrated economizer controls that
preclude simultaneous operation of the economizer and mechanical
cooling.
2. Water - cooled water chillers with w aterside economizer.
1413.4 Humidification: If an air economizer is required on a cooling system for
which humidification equipment to be provided to maintain minimum indoor
humidity levels, then the humidifier shall be of the adiabatic type (direct evaporative
media or fog atomization type).
Exceptions:
1. Health care facilities where WAC 246 - 320 -525 allows only steam
injection humidifiers in ductwork downstream of final filters. 1412.6
Combustion Heating Equipment Controls: Combustion heating
equipment with a capacity over 225,000 Btu /h shall have modulating
or staged combustion control.
2. Systems with water economizer
3. 100% outside air systems with no provisions for air recirculation to the
central supply fan.
4. Nonadiabatic humidifiers cumulatively serving no more than 10% of a
building's air economizer capacity as measured in cfm. This refers to
the system cfm serving rooms with stand alone or duct mounted
humidifiers.
1414 Ducting Systems
1414.1 Sealing: Duct work which is designed to operate at pressures above 1/2 inch
water column static pressure shall be sealed in accordance with Standard RS- 18.
Extent of sealing required is as follows:
1. Static pressure: 1/2 inch to 2 inches; seal transverse joints.
2. Static pressure: 2 inches to 3 inches; seal all transverse joints and
longitudinal seams.
3. Static pressure: above 3 inches; seal all transverse joints, longitudinal
seams and duct wall penetrations.
Duct tape and other pressure sensitive tape shall not be used as the primary
sealant where ducts are designed to operate at stati c pressures of 1 inch W.C. or
greater.
1414.2 Insulation: Ducts and plenums that are constructed and function as part of
the building envelope, by separating interior space from exterior space, shall meet all
applicable requirements of Chapter 13. These re quirements include insulation
installation, moisture control, air leakage, and building envelope insulation levels.
Unheated equipment rooms with combustion air louvers must be isolated from the
conditioned space by insulating interior surfaces to a minimu m of R -11 and any
exterior envelope surfaces per Chapter 13. Outside air ducts serving individual
supply air units with less than 2,800 cfm of total supply air capacity shall be insulated
2. Combustion air intakes. 2006 Washington State Nonreside
3. Gravity (nonmotorized) dampers are acceptable in buildings less
than 3 stories in height.
4. Gravity (nonmotorized) dampers are acceptable in exhaust and relief
outlets in the first story and levels below the first story of buildings
three or more stories in height.
1412.4.2 Optimum Start Controls: Heating and cooling systems with design supply
air capacities exceeding 10,000 cfm shall have optimum start controls. Optimum
start controls shall be designed to automatically adjust the start time of an HVAC
system each day to bring the space to desired occupied temperature levels
immediately before scheduled occupancy. The control algorithm shall, as a
minimum, be a function of the difference between space temperature and occupied
setpoint and the amount of time prior to scheduled occupancy.
1412.5 Heat Pump Controls: Unitary air cooled heat pumps shall include
microprocessor controls that minimize supplemental heat usage during start-up, set-
up, and defrost conditions. These controls shall anticipate need for heat and use
compression heating as the first stage of heat. Controls shall indicate when
supplemental heating is being used through visual means (e.g., LED indicators).
1412.6 Combustion Heating Equipment Controls: Combustion heating equipment
with a capacity over 225,000 Btu /h shall have modulating or staged combustion
control. 000
EXCEPTIONS: 1. Boilers 2 Radiant heaters
1412.7 Balancing: Each air supply outlet or air or water terminal device shall have
a means for balancing, including but not limited to, dampers, temperature and
pressure test connections and balancing valves.
ntttdliEtilfdatds rfi'aQGt4pl1fGatiicRilinices to a minimu m of R -11 and any
exterior envelope surfaces per Chapter 13. Outside air ducts serving individual
supply air units with less than 2,800 cfm of total supply air capacity shall be insulated
to a minimum of R -7 and are not considered building envelope. Other outside air
duct runs are considered building envelope until they,
1. connect to the heating or cooling equipment, or
2. are isolated from the exterior with an automatic shut -off damper complying
with Section 1412.4.1.
Once outside air ducts meet the above listed requirements, any runs within
conditioned space shall comply with Table 14 -5 requirements.
Other ducts and plenums shall be thermally insulated per Table 14 -5.
Exceptions:
1. Within the HVAC equipment.
2. Exhaust air ducts not subject to condensation.
3. Exposed ductwork within a zone that serves that zone.
1415 Piping Systems
1415.1 Insulation: Piping shall be thermally insulated in accordance with Table 14 -6.
Exception: Piping installed within unitary HVAC equipment.
Water pipes outside the conditioned space shall be insulated in accordance with
Washington State Plumbing Code (WAC 51 -26)
1416 Completion Requirements (Refer to NREC Section 1416 and the Building
Commissioning Guidelines, published by the Building Commissioning Association,
for complete text and guidelines for building completion and commissioning
requirements.)
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
•
PLAN P F&
ACTIVITY NUMBER: M08 -016 DATE: 01 -16 -08
PROJECT NAME: AMERICAN FAMILY INSURANCE
SITE ADDRESS: 13038 INTERURBAN AVE S - STE 120
X Original Plan Submittal
_ Response to Correction Letter #
Response to Incomplete Letter #
Revision # After Permit Issued
DEPARTMENTS:
B� ����
I�rig'DivisL
Public Works
Complete
Comments:
-v
TUES/THURS ROUTING:
Please Route
REVIEWER'S INITIALS:
Incomplete
Structural Review Required
APPROVALS OR CORRECTIONS:
Approved n Approved with Conditions
Notation:
REVIEWER'S INITIALS:
Documents/routing slip.doc
2 -28-02
5 '1 - -oS
Fire Prevention
Structural
n
•
8hNG SLIP
DUE DATE: 01 -17 -08
DATE:
DATE:
Planning Division
Permit Coordinator
Not Applicable
No further Review Required
U
1
p 4
Permit Center Use.Only_
INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED:
Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
DUE DATE: 02 -14 -08
Not Approved (attach comments) ❑
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
License Information
License
NOMECSM975C7
Licensee Name
NO MECHANICAL SHEET METAL INC
Licensee Type
CONSTRUCTION CONTRACTOR
UBI
602274821
Ind. Ins. Account Id
#1
Business Type
CORPORATION
Address 1
PO BOX 1581
Address 2
City
AUBURN
County
KING
State
WA
Zip
98071
Phone
2537351825
Status
ACTIVE
Specialty 1
AIR HEAT,VENTILATION,EVAPORAT
Specialty 2
SHEET METAL
Effective Date
2/27/2003
Expiration Date
2/27/2009
Suspend Date
Separation Date
Parent Company
Previous License
NORTHMS133RZ
Next License
Associated License
Bond Information
Bond
Bond
Company
Name
Bond
Account
Number
Effective
Date
Expiration
Date
Cancel
Date
Impaired
Date
Bond
Amount
Received
Date
#1
CBIC
SE8659
02/01/2003
Until
Cancelled
$6,000.00
02/27/2003
Business Owner Information
Name
Role
Effective Date
Expiration Date
AROMIN, MICHAEL P
PRESIDENT
02/27/2003
AROMIN, CHRISTI C
SECRETARY
02/27/2003
Look Up a Contractor, Elect iic�ian or Plumber License Detail
Washington State Department of Labor and Industries
GeneraUSpecialty Contractor
A business registered as a construction contractor with L &I to perform
construction work within the scope of its specialty. A General or Specialty
construction Contractor must maintain a surety bond or assignment of
account and carry general liability insurance.
•
Page 1 of 2
https: // fortress .wa.gov /lni/bbip /printer.aspx ?License= NOMECSM975C7 01/23/2008
EXIST
EXIST/ Ne EXAI.
SEPARATE PERMIT
REQUIRED FOR:
0 Mechanical
IV Electrical
Plumbing
al Gas Piping
City of Tukwila
[BUILDING DIVISION
Ti2-A s P e e em L Car review approval is subject to eff to and
App.oval of aeon documents does not
the violation of any adopted code or
FILE COPY
Permit No
,!AN 1 6 2008
PERMIT CENTER
No ms changee
el work wfthout p pprovaf
Tukwila
NOTE: Revisions will require a new pian submittal ,
and may include additional plan reiiew fees. '
DATE: i w* / - c8
City of Tukwila
BUILDING DIVISION
P P4a oo03000I)
7 /N.J.\ NI
AMeiztcAAr Mtc.r INsArvC.E
T'- -;
v.TC
1 34 1N7'Eg.vK4,au Avemue So,
No 12. lit +A-1 ICA L. E -Er
L I:
41e AL r53- r `!'t + -a
Of Tukwila
. BUi+i �l,��: vim,.._
"If
REVIEWED FOR
APPROVE
CD ®VED
S
JAN 1 `0
/Zo
DRAWN BY ! # F #A
REVISED
DRAWING NUMBER
M •