Loading...
HomeMy WebLinkAboutPermit M08-138 - WESTFIELD SOUTHCENTER MALL - SUBWAYSUBWAY 2600 SOUTHCENTER MALL M08 -138 Parcel No.: 6364200010 Address: Suite No: Owner: Name: Address: 2600 SOUTHCENTER MALL TUKW Tenant: Name: SUBWAY Address: 2600 SOUTHCENTER MALL FC -6 , TUKWILA WA WESTFIELD PROPERTY TAX DEPT PO BOX 130940 , CARLSBAD CA Contact Person: Name: MARCIA PEDDICORD Address: 633 SOUTHCENTER MALL TRAILER #3 , TUKVVILA WA Contractor: Name: PACIFIC TECH INTERIORS INC Address: BLDG 1 STE B , 12315 MUKILTEO SPEEDWAY Contractor License No: PACIFTIO85D3 DESCRIPTION OF WORK: MECHANICAL SYSTEM FOR NEW MALL SPACE TENANT IMPROVEMENT Value of Mechanical: $25,000.00 Type of Fire Protection: SPRINKLERS /AFA doc: IMC -10/06 City.f Tukwila Furnace: <100K BTU 0 >100K BTU 0 Floor Furnace 0 Suspended/Wall/Floor Mounted Heater 0 Appliance Vent 0 Repair or Addition to Heat/Refrig /Cooling System.... 1 Air Handling Unit <10,000 CFM 1 >10,000 CFM 0 Evaporator Cooler 0 Ventilation Fan connected to single duct 0 Ventilation System 0 Hood and Duct 0 Incinerator: Domestic 0 Commercial/Industrial 0 Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila. MECHANICAL PERMIT EQUIPMENT TYPE AND QUANTITY * *continued on next page ** Permit Number: Issue Date: Permit Expires On: Phone: Phone: 206 -802 -6071 Phone: Expiration Date: 03/19/2009 M08 -138 06/26/2008 12/23/2008 Fees Collected: $451.25 International Mechanical Code Edition: 2006 Boiler Compressor: 0 -3 HP /100,000 BTU 0 3 -15 HP /500,000 BTU 0 15 -30 HP /1,000,000 BTU.. 0 30 -50 HP /1,750,000 BTU.. 0 50+ HP /1,750,000 BTU 0 Fire Damper 0 Diffuser 0 Thermostat 1 Wood/Gas Stove 0 Water Heater 0 Emergency Generator 0 Other Mechanical Equipment M08 -138 Printed: 06 -26 -2008 Permit Center Authorized Signature: Signature: doc: IMC -10/06 • City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us Nvvr-pig • Permit Number: M08 -138 Issue Date: 06/26/2008 Permit Expires On: 12/23/2008 Date: OUN- (4 I hereby certify that I have read and ginned this permit and know the same to be true and correct. All provisions of law and ordinances governing this work will be complied whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating construction or the performance of work. I am authorized to sign and obtain this mechanical permit. Date: Print Name: A/it/m.4,4 e Z:1 d 55 This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. M08 -138 Printed: 06-26 -2008 • City of Tukwila Parcel No.: 6364200010 Address: 2600 SOUTHCENTER MALL TUKW Suite No: Tenant: SUBWAY 1: ** *BUILDING DEPARTMENT CONDITIONS * ** Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us PERMIT CONDITIONS • Permit Number: M08 - 138 Status: ISSUED Applied Date: 05/09/2008 Issue Date: 06/26/2008 2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the Building Official. 3: All mechanical work shall be inspected and approved under a separate permit issued by the City of Thkwila Permit Center (206/431- 3670). 4: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to start of any construction. These documents shall be maintained and made available until final inspection approval is granted. 5: Readily accessible access to roof mounted equipment is required. 6: All construction shall be done in conformance with the approved plans and the requirements of the International Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code. 7: Manufacturers installation instructions shall be available on the job site at the time of inspection. 8: All plumbing and gas piping work shall be inspected and approved under a separate permit issued by the Cityof Tukwila Permit Center. 9: All electrical work shall be inspected and approved under a separate permit issued by the City of Thkwila Building Department (206- 431 - 3670). 10: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the Building Official from requiring the correction of errors in the construction documents and other data. doc: Cond - 10/06 * *continued on next page ** M08 -138 Printed: 06 -26 -2008 • City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206431-3665 Web site: http: / /www.ci.tukwila.wa.us • I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provision of any other work construction or the performance of work. Signature: Wdz,, e Print Name: l/4"). -s? 1 C1r_ doc: Cond -10/06 M08 -138 Date: ordinances governing or local laws regulating Printed: 06 -26 -2008 CITY OF TUKWILA Community Development Department Public Works Department Permit Center 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 hitp://www.ci tuktt•iln.wa.us Applications and plans must be complete in order to be accepted for plan review. Applications will not be accepted through the mail or by fax. * *Please Print ** SITE LOCATION King Co Assessor's Tax No.: 4 34. 't 2 — tom/ d Site Address: 2 6e0 SoaM A44 (( F! Co Suite Number: Floor:' Tenant Name: cSLt 6w , New Tenant: ®' Yes El „No Property Owners Name: Wed 4'e (/ CI0rf e.rtt Y6 or Mailing Address: /16D/ 1, (Shire. f3 &tied I / / LS Afrce k7 C-4- ( �3 - City State Zip CONTACT PERSON who do we contact wh your permit'is ready be issued ` Name: iha ,-t t cc 79 d ` ��- � Day Telephone: Telephone: . 34 ) 4— �d2 — 44 71 W Mailing Address: , 33 Gii /-4,- , /rat# 3 Seel -/-1/, �c�1 78-i ' City State Zip Fax Number: E -Mail Address: Pr e,. /.1 em-a. G 4it °54 . e 1,1. «tr) GENERAL CONTRACTOR INFORMATION (Contractor Information for Mechanical (pg 4) for Plumbing and Cas Piping (pg 5)) Company Name: 6.'7 ! e_-v Mailing Address: 3(' ,, DD re-,/-- y Ade. 1s Contact Person: A6;1 Ste; llii E -Mail Address: kGm, • 4 € 5? i Me., Company Name: TA7) Mailing Address: City Day Telephone: Fax Number: Expiration Date: Contact Person: E -Mail Address: Contractor Registration Number: ARCHITECT OF RECORD All plans must be wet stamped by Architect of Record ENGINEER OF RECORD - All plans must be wet stamped by Engineer of Record Company Name: J p per- i Mailing Address: -AQY A/ eh/ ti 'Building Permit NO: McCh4hical " Permit Nc Plumbing/Gas Permit State Zip Seal *67' City State Zip Day Telephone: r-266- 7/3- 7/ Fax Number: D°./ hOfil 14 A41 i City ' State Zip Contact Person: Day Telephone: 3 /3— Sks- 5574 E -Mail Address: Fax Number: Q:Npplicarionr.Fomts- Applications On Lin&3 -71'J6 - Permit Apptication.dec Revise& 9 -2006 bb Page I of 6 Unit Type: Qty Unit Type: Qty Unit Type: Qty Boiler /Compressor: Qty Fumace <I00K BTU Air Handling Unit >10,000 CFM Fire Damper 0 -3 HP /100,000 BTU Fumace >100K. BTU :.,"=: `_- .77... Cooler Diffuser 3 -15 HP /500.000 BTU Floor Furnace Ventilation Fan Connected to Single Duct Thermostat • / 15 -30 HP /1,000,000 BTU Suspended/Wall/Floor Mounted Heater Ventilation System Wood/Gas Stove 30 -50 HP /1,750,000 BTU Appliance Vent Hood and Duct Emergency Generator 50+ HP /I,750,000 BTU Repair or Addition to Heat/Refrig /Cooling System 1 Incinerator - Domestic Other Mechanical Equipment Air Handling Unit <10,000 CFM / Incinerator — Command MECHANICAL PERMIT INFORMATION: = 206=431,3670 MECHANICAL CONTRACTOR INFORMATION Company Name: -Ter) Mailing Address: City state Zip Contact Person: Day Telephone: E -Mail Address: Fax Number: Contractor Registration Number: Expiration Date: Valuation of Mechanical work (contractor's bid price): $ ( 00 jt e A Scope of Work (please provide detailed information): Use: Residential: New .... ❑ Replacement .... ❑ Commercial: New ....Er Replacement .... ❑ Indicate type of mechanical work being installed and the quantity below: Fuel Type: Electric E Gas....❑ Other: Q:kApplicatinns'Fomet- Applications On Line&3 -2016 - Permit Apoiication.doc Rev,sed: 9.211116 bh Page 4 of 6 PERMIT APPLICATION NOTES Applicable, to all permits in this application Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject to possible revision by the Permit Center to comply with current fee schedules. Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation. I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING OR 4UTHO ED AG "fit Signature: I Print Name: Building and Mechanical Permit The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be requested in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition). Plumbing Permit The Building Official may grant one extension of time for an additional period not exceeding 180 days. The extension shall be requested in writing and justifiable cause demonstrated. Section 103.4.3 Uniform Plumbing Code (current edition). /h.C.ii1 7' DDr cai2D Mailing Address: 67 n car M e k. - Date Application Accepted: Date Application Expires: Staff Initials: ue I 0 Npplicatons`fomu- Applications On Line`3 -2006 - Permit Applicaion.doc Reviud: 9. bh Day Telephone: City Date: .264 -82. 2- 6d 7/ LOA_ le /k7 state Zip Page 6 of 6 RECEIPT NO: R08 -02312 Initials: WER User ID: 1655 SET TRANSACTIONS: Set Member ACCOUNT ITEM LIST: Description City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 -431 -3670 Fax: 206 -431 -3665 Web site: http: / /www.ci.tukwila.wa.us Payee: PACIFIC TECH INTERIORS INC. SET ID: 0626 SET NAME: SUBWAY Amount D08 -201 1,958.50 MQLTIRI 361.00 PG08 -123 596.00 TOTAL: 2,915.50 TRANSACTION LIST: Type Method Description Amount Payment Check 121657 BUILDING - NONRES MECHANICAL - NONRES PLAN CHECK - NONRES PLUMBING - NONRES STATE BUILDING SURCHARGE SET RECEIPT TOTAL: Payment Date: 06/26/2008 Total Payment: 2,915.50 2,915.50 2,915.50 Account Code Current Pmts 000/322.100 1,594.00 000.322.102.00.0 361.00 000/345.830 720.00 000.322.103.00.0 236.00 000/386.904 4.50 TOTAL: 2,915.50 4158 06/26 ?711 TOTAL 2915.50 Receipt No.: R08 -01551 Initials: WER User ID: 1655 Payee: JIMMY ENTERPRISES ACCOUNT ITEM LIST: Description PLAN CHECK - NONRES City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 -431 -3670 Fax: 206 -431 -3665 Web site: http: / /www.ci.tukwila.wa.us RECEIPT Parcel No.: 6364200010 Permit Number: M08 -138 Address: 2600 SOUTHCENTER MALL TUKW Status: PENDING Suite No: Applied Date: 05/09/2008 Applicant: SUBWAY Issue Date: TRANSACTION LIST: Type Method Descriptio Amount Payment Check 3799 90.25 Account Code Current Pmts 000/345.830 90.25 Total: $90.25 Payment Amount: $90.25 Payment Date: 05/09/2008 03:18 PM Balance: $361.00 2263 05/12 9711 TOTAL 90.25 doe: Receiot -06 Printed: 05-09 -2008 Proje 71 beA,44 Type of Inspection: \ rt N4 / Address: P-(0'60 / i I Date Called: Special Instructions: Date Wanted: g — 3 — 0 e em. Requester: No: - Ph No: on - 576 -/6o3 INSPECTION RECORD Retain a copy with permit INSP ION NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 COMMENTS: Provfiii 1-3- $6 F .00 • EINSPECTION FEE RE • IRED. ' nor to inspection, fee must be pa d - 6300 Southcenter Blvd.,.uite 1 10. Call to schedule reinspection. Recei • No.: 'Date: Approved per applicable codes. El Corrections required prior to approval. Project: >4,,4- Type of Inspection: gov. ree ti Address: 2400 Pi9 Date Called: Special Instructions: Date Wanted: 2 -- 4 a.m. P Requester: J.S4 Phone No: I INSPECTION RECORD Retain a copy with permit t4 -17 INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 ® Approved per applicable codes. Corrections required prior to approval. COMMENTS: k t2 1 o si,Wt a Inspector: Date: 7-2/ $58.00 REINSPECTION FEE REQUIRED. Prior o inspection. fee must be paid at 6300 Southcenter Blvd., Suite 100. Call the schedule reinspection. Receipt No.: !Date: �i.Ai.�..ss.l....— -<w., vine ,....r...s..s.u0� _. ih�* nM. 1be. .3+:�..FS'1A_.dWdi- .we.'�`"� - .s'3.�,.�` - Project: 5 v e vv at-i Type of Inspection: FA Fire Alarm: Address: 2. ,. C . (VI r ( Suite #: r c. v Contact Person: A, ,w - 6 u ct- ,,, 4-yJ Special Instructions: Phone No.: Needs Shift Inspection: Sprinklers: Fire Alarm: Hpod & Duct: Monitor: Pre -Fire: Permits: - Occupancy Type: INSPECTION NUMBER I NSPECTION RECORD Retain a copy with permit OP, -F 5 Ll l PERMIT NUMBERS Ue- 5 - 3(c?— CITY OF TUKWILA FIRE DEPARTMENT 444 Andover Park East, Tukwila, Wa. 98188 206- 575 -4407 Approved per applicable codes. Corrections required prior to approval. COMMENTS: CAS N i) i2 o u►t ov / NV. D lC SAM P c —,4 s @_ ►� ,�--_ l: (,N OIL Inspector: v 1617-- Date: L v1 z) I6 C6 Hrs.: r ° $80.00 REINSPECTION FEE REQUIRED. You will receive an invoice from e City of Tukwila Finance Department. Call to schedule a reinspection. Word /Inspection Record Form.Doc 1/13/06 T.F.D. Form F.P. 113 ANF & ASSOCIATES April 7, 2008 Westfield Design & Construction 633 South Center Trailer #3 Seattle, CA 98188 Attn: Bryan Low, Tenant Coordinator RE: HVAC Equipments on Level 3 South Center, Tukwila, WA Dear Bryan: We have completed our review of the level 3 floor framings at the designated HVAC equipment areas based on the following criteria: 1) Maximum single equipment weight of 1,500 lbs with a plan area of 6 square feet minimum. 2) There is no floor opening required under the equipment. 3) Minimum clearance between equipments is 3' -O" on 4 sides typical. Our review shows that the level 3 floor framings at the designated HVAC equipment areas can safely support the HVAC equipments if the criteria as mentioned above are met. Level 3 floor framings under the equipments which do not meet the criteria as mentioned above shall be reviewed and reinforced as required by a professional engineer registered in the state of Washington. Please call us should you have any questions regarding the above. • Sincerely yours, ANF & Associates Michael H. Wang, P.E. Associate FILE COPY Permit No. I IMAMS i'/( e. ( 2.0P fr, I A!W"D) rh E 1 D)'2008'23906 Letter to Westfield L1 i g (' re H1 AC level 3a1 South Center ,MIaU dated 4-7-2008 Consulting Structural Engineers s p VIE�11l=Dr o _ _.� E COMPLIANCE NCE APPROVED MAY 2 0 22808 Cs ►1 Of Tukwila B ILDING DIVISION MO8 138 9420 Telstar Ave., Suite 118 • Flair Commerce Center • El Monte, CA 91731 • Tel: (626) 4484182 • Fax (626) 448 -8092 RECEIVEf MAY — 9 2008 PERMIT CENTL IEs1 (626) 448 -8182 ANF & ASSOCIATES Fait (626) 4484092 Consulting Structural Engineers E-mai anti688C Cbeil.net 9420 Tatum Avenue, Suits 1 BI Montc, CA 91731 S DC (-71-1 _- - T��.k u.� t: p► , l uA SM. MECH. CURB PER MECHANICAL DRAWINGS \\ CONC. TOPPING -, OVER METAL DECK' SECTION A -A C8x1 1.5 TYP. HILTI ---5/� KWIK XP. DOLT x4' EMBED. (ICBO# 4780) EDGE OF NEW OPEN'G PL.1 /4x8 C 10x 15.3 OR W12x14 PL.1/4x8 - NOTE (E)STL. BM -- DO NOT OVERCUT OF CONCRETE FLOOR OPEN'G CORE DRILL 4 "O OPEN'G © CORNERS & THEN SAWCUT THE REST OF OPEN'G. AL 6' -0" -e- 1 MAX. PLAN B 3/16 SECTION B -B v w 0 FLOOR BEAMS SEE PLAN ' W/ 1 " RETURN 3/16 ,:TYP. TYP. CONC. FLOOR OPENING DETAIL SK1- 031008 Joe No. l By D y DArt '3 —!D -0a Os RECEaVEF MAY —9 2008 PERMIT CENTEt 1hL (626) 448-8182 AN 2 1 ! I & 8 $ of -TH e -�T &n,. mnt168( `e°° °ee 9420 Tedder Awe, Suite 118, ID Monte, CA 91731 Tu k iai i L f} , wA Joao No. t r BY D Dots S 5►+,. OF N m METAL DECK W/-. CONC. FILL I V-0"1 1' - 4 . • I MAX. ; II I! 2' =0" A I SINGLE OPENING (N) L3x3x 1 /4 W/5/8"0 KWIK BOLT II TO BOTTOM OF FLUTE ®12 "O.C. WITH ,• 4 1/2" EMBED. GROUP OF OPEN'GS NOTES: 1. DO NOT CUT OPENINGS IN DECK UNTIL 7 DAYS AFTER CONC. HAS BEEN POURED 2. SINGLE OPENINGS NOT LARGER THAN 8" DIAMETER OR 8" SQUARE REQUIRE NO ANGLES. 3. CONC. OPENINGS OR GROUP OF OPENING EXCEEDING 16" OR CUTTING 2 BOTTOM FLUTES REQUIRE SECONDARY BEAM REINFORCEMENT AS PER DETAIL SK 1- 031008 NP. METAL DECK ROOF FLOOR OPEN'G W/ CONC. TOPPING SK2- 031008 RECEIVED MAY - 9 2008 PERMIT CENT& Project Info Project Address 2600 Fc6 southcenter Dwell Date 5/9/2008 Tukwila, WA 98188 For Building Department Use Applicant Name: Keith L. Smith Applicant Address: 1725 WestlakeAve. N., Suite 210 Applicant Phone: Seattle, WA 98109 FILE COPY Pt MIIt No. Project Summary PRJ -SUM 2006 Washington State Nonresidential Energy Code Compliance Forms 2006 Washington State Nonresidential Energy Code Compliance Form Mob - (%8 Revised July2007 RECEWEE MAY - 9 2008 PERMIT CENT& Cooling Equipment Schedule Equip. ID Brand Name' Model No. Capacity2 Btu/h Total CFM OSA CFM or Econo? SEER or EER IPLV Location RTU -1 Carrier 50 TM 006 57000 1950 Econo M -1 Fan Equipment Schedule Equip. ID Brand Name' Model No. CFM SPA HP/BHP Flow Control Location of Service Efficiencv4 FMB -4 carrier electric heat 12 kw Seattle, WA 98109 Heating Equipment Schedule Equip. ID Brand Name' Model No. Capacity Btu/h Total CFM OSA cfm or Econo? Input Btuh Output Btuh Efficiencv4 FMB -4 carrier electric heat 12 kw Seattle, WA 98109 Project Info Project Address 2600 FC6 Southcenter Mail Date 5/9/2008 Tukwila, WA 98188 For Building Dept. Use Applicant Name: Keith L. Smith Applicant Address: 1725 WeatlakeAve. N., Suite 210 Applicant Phone: Seattle, WA 98109 2006 Washington State Nonresidential EnergyCode Compliance Forms Mechanical Summary MECH -SUM Project Description Briefly describe mechanical system type and features. ©Indudes Plans 2006 Washington State Nonresidential Energy Code Compliance Form Drawings must contain notes requireing compliance with commissioning requirements - Section 1416 Retised July2007 Compliance Option • Simple System 0 Complex System 0 Systems Analysis (See Decision Flowchart (over) for qualifications. Use separate MECH -SUM for simple & complex Equipment Schedules The following information is required to be incorporated with the mechanical equipment schedules on I the plans. For projects without plans, fill in the required information below. 'If available. 2 As tested according to Table 14 -1A through 14 -1G. 3 If required. 4 COP, HSPF, Combustion Efficiency, or AFUE, as applicable. 5 Flow control types: variable air volume(VAV), constant volume (CV), or variable speed (VS). System Description If Heating /Cooling • Constant vol? • Air cooled? • Packaged sys ?p <20,000 Btuh? See Section 1421 for full description or Cooling Only. Split system? 0 Economizer included? • of Simple System qualifications. If Heating Only. • <5000 cfm? 0 <70% outside air? Heating Only 2006 Washington State Nonresidential Energy Code Compliance Form Mechanical Summary (back) MECH -SUM Decision Flowchart Use this flowchart to determine if project qualifies for Simple System Option. If not, either the Complex System or Systems Analysis Options must be used. otal Ca.. wo economiz <240,000 Btuh or 10 %? Reference Section 1421 Heating/Cooling or Cooling Only R eference Section 1423) Complex Systems Refer to MECH -COMP Mechanical Complex Systems for assistance in determining which Complex Systems requirements are applicable to this project. Mechanical; Permit Plans 2006 Washington State Nonresidential Energy Code Compliance Forms Checklist MECH -CHK Revised July 2007 Project Address 2600 FC6 Southcenter Mall 'Date 5/9/2008 The following information is necessary to check a mechanical permit application for compliance with the mechanical requirements in the Washington State Nonresidential Energy Code. Applicability (yes, no, n.a.) I Code Section I Component I Information Required I Location on Plans I Building Department Notes HVAC REQUIREMENTS (Sections 1401 -1424) 1411 Equipment performance 1411.4 Pkg. elec. htg.& clg. List heat pumps on schedule yes 1411.1 Minimum efficiency Equipment schedule with type, capacity, efficiency M -1 1411.1 Combustion htg. Indicate intermittent ignition, flue/draft damper & jacket loss 1412 HVAC controls yes 1412.1 Temperature zones Indicate locations on plans M -1 1412.2 Deadband control Indicate 5 degree deadband minimum 1412.3 Humidity control Indicate humidistat 1412.4 Automatic setback Indicate thermostat with night setback and 7 diff. day types 1412.4.1 Dampers Indicate damper location and auto. controls & max. leakage 1412.4.2 Optimum Start Indicate optimum start controls 1412.5 Heat pump control Indicate microprocessor on thermostat schedule 1412.6 Combustion htg. Indicate modulating or staged control 1412.7 Balancing Indicate balancing features on plans 1412.8 Ventilation Control Indicate demand control ventilation for high - occupancy areas 1422 Thermostat interlock Indicate thermostat interlock on plans 1423 Economizers Equipment schedule 1413 Air economizers 1413.1 Air Econo Operation Indicate 100% capability on schedule 1413.1 Wtr Econo Operation Indicate 100% capacity at 45 degF db & 40 deg F wb 1413.2 Water Econo Doc Indicate clg load & water econoe & clg tower performance 1413.3 Integrated operation Indicate capability for partial cooling 1413.4 Humidification Indicate direct evap or fog atomization w/ air economizer 1414 Ducting systems 1414.1 Duct sealing Indicate sealing necessary 1414.2 Duct insulation Indicate R -value of insulation on duct 1415.1 Piping insulation Indicate R -value of insulation on piping 1416 Completion Requirements 1416.2.1 Commissioning Provide commissioning plan 1416.2.2 -3 Sys.Bal & Func.Test Indicate air and water system balancing & functional testing 1416.2.4 Commissioning Indicate O &M manuals, record drawings, staff training 1416.2.5 Comm. Report Indicate requirements for prelim. & final commissioning report 1434 Separate air sys. Indicate separate systems on plans yes Mechanical Summary Form Completed and attached. Equipment schedule with types, input/output, efficiency, cfm, hp, economizer SERVICE WATER HEATING AND HEATED POOLS (Sections 1440 -1454) 1440 Service water htg. 1441 Elec. water heater Indicate R -10 insulation under tank 1442 Shut -off controls Indicate automatic shut -off 1443 Pipe Insulation Indicate R -value of insulation on piping 1452 Heat Pump COP Indicate minimum COP of 4.0 1452 Heater Efficiency Indicate pool heater efficiency 1453 Pool heater controls Indicate switch and 65 degree control 1454 Pool covers Indicate vapor retardant cover 1454 Pools 90+ degrees Indicate R -12 pool cover 2006 Washington State Nonresidential Energy Code Compliance Form ACTIVITY NUMBER: M08 -138 DATE: 05 -09 -08 PROJECT NAME: SUBWAY SITE ADDRESS: 2600 SOUTHCENTER MALL FC -6 X Original Plan Submittal Response to Correction Letter # Response to Incomplete Letter # Revision # After Permit Issued DEPARTMENTS: B slon Public Works ❑ Please Route REVIEWER'S INITIALS: Documents/routing slip.doc 2 -28 -02 PERMIT COORD COPY PLAN REVIEW/ROUTING SLIP 6'1( ! Fire Prevention , 4 Structural Review Required TUES/THURS ROUTING: DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete Incomplete ❑ Planning Division Structural ❑ Permit Coordinator DUE DATE: 05 -1 3-08 Comments: Permit Center Use Only INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED: Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: n No further Review Required DATE: APPROVALS OR CORRECTIONS: DUE DATE: 06 -10 -08 Approved ❑ Approved with Conditions 4 Not Approved (attach comments) ❑ Notation: REVIEWER'S INITIALS: DATE: Not Applicable n Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: License Information License PACIFTI085D3 Licensee Name PACIFIC TECH INTERIORS INC Licensee Type CONSTRUCTION CONTRACTOR UBI 601375654 Ind. Ins. Account Id 83473400 Business Type CORPORATION Address 1 12428 HWY 99 UNIT 50 Address 2 City EVERETT County SNOHOMISH State WA Zip 98204 Phone 4253553903 Status ACTIVE Specialty 1 GENERAL Specialty 2 UNUSED Effective Date 3/23/1992 Expiration Date 3/19/2009 Suspend Date Separation Date Parent Company Previous License Next License Associated License Bond Information Bond Bond Company Name Bond Account Number Effective Date Expiration Date Cancel Date Impaired Date Bond Amount Received Date #3 CBIC 659929 03/19/2002 Until Cancelled $12,000.00 03/18/2002 #2 CBIC 659929 03/19/1998 03/19/2002 $6,000.00 Business Owner Information Name Role Effective Date Expiration Date CROSS, WILLIAM C PRESIDENT 01/01/1980 STONE, JOHN 0 JR VICE PRESIDENT 01/01/1980 Look Up a Contractor, Electria or Plumber License Detail Washington State Depaitment of Labor and Industries General/Specialty Contractor A business registered as a construction contractor with L &I to perform construction work within the scope of its specialty. A General or Specialty construction Contractor must maintain a surety bond or assignment of account and carry general liability insurance. • Page 1 of 2 https: // fortress .wa.gov /lni/bbip /printer.aspx ?License= PACIFTIO85D3 06/26/2008 PACKAGED ROOFTOP UNIT SCHEDULE MARK SERVING TOTAL SUPPLY CFM MIN. O.A. CFM EXTERNAL SP (in w.c.) NOMINAL TONNAGE HEATING SECTION ELECTRICAL BASED ON CARRIER MODEL NUMBER OPTIONS UNIT WEIGHT (LBS) KW VOLTAGE PHASE UNIT M.C.A. UNIT M.O.C.P. RTU -1 SUBWAY 1,950 390 0.75 5 12.0 208 30 54.2 60 50 TM 006 1-12 800 AIR DEVICE SCHEDULE MARK DESCRIPTION SIZE MAXIMUM CFM MAX. P.D. (in. w.g.) MAXIMUM NC LEVEL BASED ON APPLICABLE NOTES MANUFACTURER MODEL SD -1 SQUARE LOUVER FACED CEILING DIFFUSER 24 "x24" SEE CAPACITY SCHEDULE 0.1" 30 TITUS TMSA 1, 2, 3, 8 RG -1 EGGCRATE RETURN GRILLE 24 "x12" 1100 0.1" 30 TITUS 50F 1, 2, 3, 4, 8 AIR DEVICE CAPACITY SCHEDULE MARK CFM RANGE NECK SIZE (inches) SD -1 0 - 250 8 "0 251 - 425 10 "0 426 - 700 12 "0 701 - 1000 14 "0 SHEET METAL NOTES 1. THESE DRAWINGS ARE DIAGRAMMATIC AND INDICATE THE GENERAL INTENT OF THE WORK. PROVIDE SHEET METAL SYSTEMS COMPLETE AND PER APPLICABLE CODES INCLUDING ALL NECESSARY OFFSETS, FITTINGS, SPECIAL RADIUS OR MITERED ELBOWS WHICH ARE REQUIRED DUE TO SPACE CONSTRAINTS OR OTHER CONDITIONS. 2. CONTRACTOR SHALL COORDINATE HIS WORK WITH THE WORK OF ALL OTHER TRADES. VERIFY ALL CLEARANCES PRIOR TO THE FABRICATION OF ANY WORK. 3. DUCTWORK SHALL NOT BE LOCATED OVER ELECTRICAL EQUIPMENT /PANELS. PROVIDE REQUIRED CLEARANCE IN FRONT OF ELECTRICAL EQUIPMENT. DUCTWORK SHALL NOT INTERFERE WITH ELECTRICAL EQUIPMENT CLEARANCE. 4. THE CONTRACTOR SHALL PROVIDE ALL MISCELLANEOUS SUPPORTING STEEL, ETC. FOR THE PROPER INSTALLATION OF ALL MECHANICAL SYSTEMS. 5. COORDINATE FLOOR, WALL, ROOF PENETRATIONS, LOUVER SIZES, PAD LOCATIONS, ETC. WITH ARCHITECTURAL TRADES. 6. THE CONTRACTOR SHALL REFER TO ARCHITECTURAL REFLECTED CEILING PLANS FOR EXACT LOCATION OF GRILLES, REGISTERS, AND DIFFUSERS. 7. INSTALL MANUAL VOLUME DAMPERS AT ALL SUPPLY AIR BRANCH DUCTS TO THE DIFFUSER, BRANCH RETURN AIR DUCT, EXHAUST AIR DUCT, AND OTHER LOCATIONS AS SHOWN ON PLANS. 8. PROVIDE FLEXIBLE CONNECTION AT DIFFUSER NECK. ALL FLEXIBLE DUCT SHALL BE INSULATED AND LIMITED TO 5' -0" IN LENGTH. 9. DUCTED EXHAUST AND RETURN GRILLES SHALL BE HARD CONNECTED. 10. COORDINATE AND PROVIDE ACCESS DOORS IN HARD CEILING AREAS FOR ACCESS TO TERMINAL UNITS, BALANCING DAMPERS, TERMINAL UNIT HEATING COIL PIPING, ETC. REFER TO ARCHITECTURAL DRAWINGS FOR CEILING TYPES. 11. CONTRACTORS SHALL VERIFY THERE ARE NO COMBUSTIBLES IN THE RETURN AIR PLENUM. IF COMBUSTIBLES ARE PRESENT CONTRACTOR SHALL COORDINATE WITH ARCHITECT /ENGINEER/OWNER'S REPRESENTATIVE COURSE OF ACTION (HARD DUCT RETURN SYSTEM OR ELIMINATE COMBUSTIBLES - FIREPROOF, WRAP, ETC.) 12. ALL SHEET METAL DUCT SIZES SHOWN ARE CLEAR INSIDE DIMENSIONS. MECHANICAL NOTES 1. DUCT LINING IS NOT ALLOWED 2. ALL SUPPLY AIR, RETURN AIR, AND EXHAUST AIR DUCTWORK SHALL BE WRAPPED WITH 1" INSULATION. 3. PROVIDE AND INSTALL FIRE DAMPERS WHERE DUCTS PENETRATE RATED CONSTRUCTION. ALL DUCTS PENETRATING SHAFTS (SMOKE BARRIERS) SHALL HAVE COMBINATION FIRE/SMOKE DAMPERS ACTIVATION OF DAMPER SHALL BE SIGNALED TO FIRE ALARM PANEL. 4. PROVIDE BALANCING DAMPERS IN ALL BRANCH DUCTWORK AS REQUIRED FOR PROPER BALANCING OF THE SYSTEM. 5. THE ENTIRE CONSTRUCTION SHALL CONFORM TO THE LATEST EDITION OF N.F.P.A. SMACNA, THE SATE'S ENFORCED MECHANICAL CODE, LOCAL ORDINANCE, AND AUTHORITIES HAVING JURISDICTION. 6. EACH CONTRACTOR SHALL COORDINATE INSTALLATION OF HIS WORK WITH ALL OTHER TRADES TO AVOID CONFLICTS AND INTERFERENCES DURING CONSTRUCTION. 7. CONTRACTOR SHALL NOT RUN ANY PVC, PLASTIC MATERIALS OR ANY OTHER COMBUSTIBLE MATERIAL INSIDE THE RETURN AIR PLENUM. 8. MECHANICAL CONTRACTOR SHALL COORDINATE ALL MECHANICAL EQUIPMENT ELECTRICAL REQUIREMENTS WITH ELECTRICAL CONTRACTOR PRIOR TO ANY EQUIPMENT PURCHASE. 9. TESTING & BALANCING - ENGAGE THE SERVICES OF AN INDEPENDENT CERTIFIED TEST AND BALANCE AGENCY THAT SPECIALIZED IN AND WHO'S BUSINESS IS LIMITED TO THE TESTING AND BALANCING OF HVAC SYSTEMS AND HYDRONIC SYSTEMS. THE AGENCY SELECTED SHALL BE CERTIFIED BY ASSOCIATED AIR BALANCE COUNCIL (AABC) OR NATIONAL ENVIRONMENTAL BALANCING BUREAU (NEBB). AGENCY SHALL SUBMIT A COMPLETE REPORT BASED ON SMACNA "BALANCING AND ADJUSTMENT MANUAL ". THE HVAC SYSTEM SHALL BE TESTED AND BALANCED TO DEMONSTRATE THAT SPECIFIED CAPACITY AND PROPER CONTROL FUNCTIONING HAS BEEN ATTAINED. 10.START -UP FOR ALL EQUIPMENT SHALL BE CONDUCTED BY EACH MANUFACTURER'S START -UP REPRESENTATIVE. INCLUDE FINAL REPORT AND CERTIFICATE. PROVIDE OWNER'S MANUAL AND TRAINING FOR MAINTENANCE PERSONNEL FOR EACH TYPE OF EQUIPMENT. 11. ALL EQUIPMENT AND COMBUSTION VENT TERMINATION ETC. SHALL BE INSTALLED PER MANUFACTURERS RECOMMENDATIONS. VERIFY AND LOCATE EQUIPMENT BASED ON MANUFACTURERS RECOMMENDED CLEARANCES. RECTANGULAR SUPPLY DUCT CEILING NOT TO SCALE 45" CLINCH COLLAR OR ROUND SPIN -IN FITTING CONNECTION WITH MANUAL VOLUME DAMPER AND LOCKING QUADRANT. (SEE PLAN) ..11wAm■ MEM GENERAL NOTES 1. CONTRACTORS SHALL PROVIDE EQUIPMENT AND SPECIALTIES INDICATED HERE -IN TO PROVIDE A COMPLETE AND WORKING SYSTEM. 2. CONTRACTORS SHALL COMPLY WITH ALL LAWS, LOCAL ORDINANCES AND CODES OF THE STATE, FEDERAL AGENCIES AND MUNICIPALITY. CONTRACTORS SHALL SECURE AND PAY FOR ALL NECESSARY FEES AND PERMITS REQUIRED IN THE PERFORMANCE OF HIS WORK. ALL CUTTING AND PATCHING FOR NEW WORK SHALL BE DONE BY THIS CONTRACTOR WITH THE APPROVAL OF THE OWNER'S REPRESENTATIVE. 3. CONTRACTOR SHALL VISIT THE SITE AND CHECK THE EXISTING CONDITIONS BEFORE SUBMISSION OF BIDS. NO ALLOWANCE SHALL BE MADE IN BEHALF OF EXTRA EXPENSES DUE TO THE FAILURE TO MAKE SUCH AN EXAMINATION. 4. CONTRACTOR SHALL PROVIDE A COMPLETED OPERABLE SYSTEM AS HERE -IN DESCRIBED. IF THE DOCUMENTATION IS UNCLEAR OR INCOMPLETE TO THE CONTRACTOR HE SHALL SO STATE IN WRITING TO THE OWNER'S REPRESENTATIVE /ENGINEER AND REQUEST CLARIFICATION ON THOSE ITEMS REQUIRING CLARIFICATION. IF NO SUCH STATEMENT IS MADE IT SHALL BE PRESUMED THAT THE CONTRACTOR FULLY UNDERSTANDS THE INTENT OF A FUNCTION OF THE SYSTEM DESCRIBED. 5. ANY CLAIMS FOR ADDITIONAL SERVICES BASED UPON UNDERSTANDING OF THE SYSTEMS WILL NOT BE ALLOWED. CONTRACT DRAWINGS ARE DIAGRAMMATIC AND INTENDED TO CONVEY THE SCOPE OF WORK AND GENERAL ARRANGEMENT OF EQUIPMENT. DO NOT SCALE DRAWINGS. 6. CONTRACTOR SHALL COORDINATE HIS WORK WITH ALL OTHER TRADES. CONTRACTOR SHALL SECURE FINAL OCCUPANCY INSPECTION AND SUBMIT CERTIFICATES TO THE OWNER'S REPRESENTATIVE. CONTRACTOR SHALL FURNISH THE OWNER WITH A WRITTEN GUARANTEE TO CORRECT ALL IMPERFECTIONS IN MATERIALS AND WORKMANSHIP, WHICH MAY DEVELOP IN THE SYSTEMS INSTALLED AND UNDER NORMAL USE FOR A PERIOD OF ONE YEAR AFTER FINAL ACCEPTANCE BY THE OWNER. 7. BASE BID FOR EQUIPMENT IS TO BE UNITS SCHEDULED. PRICING USING ALTERNATE ACCEPTED AND LISTED MANUFACTURES SHALL STATE ALTERNATE MANUFACTURER AND MODEL NUMBER AS PART OF BID. VOLUNTARY ALTERNATES FOR EQUIPMENT NOT LISTED SHALL ONLY BE WITH WRITTEN ACCEPTANCE OF THE ENGINEER PRIOR TO BIDDING. VOLUNTARY ALTERNATES WILL NOT BE REVIEWED FOR ACCEPTANCE BY THE ENGINEER DURING THE 7 DAYS PRIOR TO BID DATE. 8. CONTRACTOR SHALL PROVIDE, STORE, PLACE AND INSTALL ALL NECESSARY EQUIPMENT REQUIRED. ALL EQUIPMENT SHALL BE INSTALLED PER THE MANUFACTURER'S RECOMMENDATIONS AND IN SUCH A MANNER AS TO FUNCTION IN ITS INTENDED USE. 9. CONTRACTOR SHALL SUBMIT SUBMITTALS FOR ALL EQUIPMENT AND MATERIALS FOR REVIEW PRIOR TO PURCHASE. 10. AFTER INSTALLATION IS COMPLETE, CONTRACTOR SHALL BE RESPONSIBLE FOR STARTUP, INSPECTORS' APPROVAL AND CLEAN UP. 11. CONTRACTOR SHALL CONFORM AND COORDINATE MALL REQUIREMENTS AND GUIDELINES PRIOR TO SUBMITTING BIDS. TRANSITION TO ROUND OR ROUND DUCT SAME AS DIFFUSER NECK UNLESS NOTED OTHERWISE. (SEE PLAN) STANDARD DIFFUSER AND DUCT CONNECTION DETAIL El El El 4 NO SCALE MANUAL AIR VOLUME DAMPER W/ LOCKING QUADRANT (TYPICAL) ...x....11 CEILING DIFFUSER (SEE PLAN) TRANSITION TO ROUND W HEN REQUIRED (SEE PLAN) MAX. 5' -0" LONG (EXTENDED) ROUND FLEXIBLE DUCT CONNECTION SAME AS _ DIFFUSER NECK DIA. (1 -90° BEND. MAX.) 7 CLAMP (TYP) ROOF NOTES FOR MECHANICAL SYSTEMS: 1. MECHANICAL EQUIPMENT LOCATIONS SHALL BE COORDINATED WITH ARCHITECTURAL TRADES AND MALL MAINTENANCE MANAGEMENT COMPANY. 2. MAINTAIN A MINIMUM OF 10' -0" BETWEEN EXHAUST AIR, PLUMBING VENTS, ETC. AND OUTSIDE AIR INTAKES ON ROOFTOP UNITS. 3. MECHANICAL CONTRACTOR SHALL COORDINATE WITH ARCHITECTURAL/STRUCTURAL TRADES ANY AND ALL REINFORCING OF ROOF REQUIRED FOR NEW RTU. 4. ALL DUCTWORK ROUTING ON ROOF SHALL BE COORDINATED WITH ARCHITECTURAL TRADES AND MALL MAINTENANCE MANAGEMENT COMPANY, 5. ALL EXPOSED DUCTWORK ON ROOF SHALL BE INSULATED AND WEATHER PROOFED WATER TIGHT. SD -1 6. ALL DUCTWORK ROOF PENETRATIONS SHALL BE SEALED 390 WATER TIGHT. 7. ALL DUCTWORK ON ROOF SHALL HAVE DUCT SUPPORTS, BASED ON MIRO MODEL #8 -DS. SPACING BETWEEN SUPPORTS SHALL BE PER MANUFACTURER RECOMMENDATIONS. MECHANICAL KEYED NOTES: (MECHANICAL KEYED NOTES APPLY TO THIS SHEET ONLY) 6 NOTES: 1. BASED ON "MIRO INDUSTRIES, INC." MODEL# 8 -DS -DB EXISTING SUPPLY AIR DUCTWORK TO REMAIN AS -IS. EXISTING SUPPLY AIR DIFFUSER TO REMAIN AS -IS. OUTLINE RTU -1 ON ROOF. COORDINATE LOCATION WITH ARCHITECTURAL TRADES AND MALL MAINTENANCE MANAGEMENT COMPANY. NEW EXHAUST VENT FOR BREAD OVEN. ROUTE VENT UP TO ROOF. PROVIDE VENT ROOF CAP WITH RAIN CAP. COORDINATE VENT ROUTING WITH ARCHITECTURAL TRADES AND MALL MAINTENANCE MANAGEMENT COMPANY. COORDINATE VENT SIZE WITH BREAD OVEN MANUFACTURER. SUPPLY AND /OR RETURN AIR DUCTWORK ON ROOF. ROUTE DUCTWORK TO CAPPED ROOF OPENING. SUPPLY AND /OR RETURN AIR DUCTWORK UP TO ROOF (RTU -1). SEE PLAN FOR DUCTWORK SIZE. ISOMETRIC DUCTWORK ON ROOF SUPPORT DETAILS 1. 90.1 ASHRAE COMPLIANT. 2. DISCONNECT. 3. LOW AMBIENT CONTROLS. 4. 24" ROOF CURB. 5. FILTER RACK, 2" FILTERS. Install smoke detector to shut down air distribution by VAV's when the total combined C F M of all VAV's (to include other tenants) sharing the same plenum space exceeds 2000 CFM. (See IMC 606.2.2 for approved method of detection RG -1 780 PACKAGED GAS -FIRED ROOFTOP UNIT OPTIONS: AIR DEVICE NOTES: 4. PROVIDE VOLUME DAMPER. SD -1 390 1 1/2" THICK THERMAL INSULATION OUTDOOR SHEET METAL SUPPLY DUCTWORK NOT TO SCALE 3" MIN 6. HORIZONTAL DISCHARGE. 7. 100% ECONOMIZER, ENTHALPY CONTROL. 8. MOTORIZED OA DAMPERS. 9. CONVENIENCE OUTLET. 10. 7 DAY PROGRAMMABLE THERMOSTAT. 20 "0 1. DESIGN CFM AS NOTED ON PLANS. 2. SEE AIR DEVICE CAPACITY SCHEDULE FOR NECK SIZE. DUCT SIZE TO DIFFUSER/REGISTER /GRILLE SHALL BE EQUAL TO NECK NECK SIZE, UNLESS OTHERWISE NOTED. 3. PROVIDE MOUNTING FRAME AND BORDER STYLE TO ACCOMMODATE THE ARCHITECT'S REFLECTED CEILING PLAN AND /OR WALL CONSTRUCTION. El 3" MIN 24x22 I RTU -1 I I 1950 CFM I 12.0 KW El 390 l BACIJBAR AREA RG -1 1170 I I 1 ......::........L ...:.....,... HVAC PLAN SCALE : 1/4" = 1' -0" 20x14 OUTDOOR DUCTWORK INSULATION DETAIL 11. OVERSIZED MOTOR AND HIGH STATIC DRIVE. 12. FACTORY AUTHORIZED START - UP. NOTES 1. ALL NEW CONSTRUCTION SHALL BE COORDINATED WITH MALL MAINTENANCE MANAGEMENT COMPANY, INCLUDING CONNECTING TO EXISTING SYSTEMS, REBALANCING EXISTING SYSTEMS, ETC. SEALER JOINT WITH MANUFACTURER RECOMMENDED INSULATION AND APPROVED SEALANT INSULATION TO BE PROVIDED WITH PROTECTIVE FINISH AND WEATHERPROOF PAINT 5. RETURN, EXHAUST, AND TRANSFER GRILLES SHALL BE 24 "x24 ", UNLESS OTHERWISE NOTED ON PLANS. 6. PROVIDE WITH MODULINEAR DIFFUSER PLENUM. 7. TRANSFER GRILLES ON PLANS INDICATED BY TG-1 (XX "0) SHALL BE PROVIDE WITH A RECTANGULAR TO ROUND NECK ADAPTER. 8. ALL AIR DEVICES SHALL HAVE OFF -WHITE FINISH UNLESS OTHERWISE NOTED. • SEPARATE PERMIT REQUIRED FOR: ❑ Mechanical UK, lectrical CIVIumbing (g Gas Piping City of Tukwila , BUILDING DIVAN ECEIVEr MAY - 9 2008 PERMIT CENTEI 633 Southcenter Seattle, WA 98188 206.246.7400 smith cc). 318 terry avenue n seethe, washington 981 206.838.5485 p 206.713.4076 m 206.464.0700 f ksmith @smithco.org http: / /www.smithco.org/ Consultant J o NGINf:ING INC. Consulting Engineers 5608 N. Charlesworth St. Dearborn Hts. Michigan 48127 Tel: (313) 565 -5580 Fax: (313) 565 -9818 emalllredenglneering @c°mcastnet JRED PROJECT NUMBER: 08028 Consultant Registratic ILE COPY pear review approval is subject to errors and omissions. Approval of construction documents does not authorize the violation of any adopted code or ordinance. Receipt of approved Field Copy and conditions is acknowledged: By iddiawd fi4 Date:, 4 /VA " Issues and Revisions City of Tuk it4la No. Date BUILDING WASION By Check 1 4 -11 -08 PERMITS K.S. 2 4-17-08 HEALTH DEPT. UP -DATE 3 5 -5 -08 UPDATE I i EEVlSIuNs Nn _ harn.e,, _ of work without prior approval of Tukwila Building Division. MOTE: Rations ions wiii require a new plan submittal and may include d it; no I an re : Project Name SUBWAY Project Number 02006088.00 Description Computer File Scale Permit No. 09 ' R E V O E S . \ '_ APPROV MAY 2 () DV 6294 friO8L38 • : \ M -1 Architect Registration All ideas, designs, arrangements, and plans indicated or represented by this drawing are owned by and the property of smith co. IIc and were created, evolved, and developed for use on and in connection with the specified project. None of such ideas, designs, arrangements or plans shall be used by or disclosed to any person, firm, or corporation for any purpose whatsoever without the written permission of smith co. IIc.