HomeMy WebLinkAboutPermit M08-238 - BEST BUYBEST BUY
17364 SOUThCENTER PY
M08-.238
Parcel No.: 2623049079
Address:
Suite No:
17364 SOUTHCENTER PY TUKW
Tenant:
Name: BEST BUY
Address: 17364 SOUTHCENTER PY , TUKWILA WA
Owner:
Name: KIR TUCKWILA 050 LLC /KIMCO Phone:
Address: PROPERTY TAX DEPARTMEMT , 3333 NEW HYDE PK RD STE 100
Contact Person:
Name: ARNIE HAUGEN
Address: 500 EAST MAIN , MONROE WA
Contractor:
Name: G & S HEATING COOLING /ELEC INC
Address: 500 EAST MAIN ST , MONROE WA
Contractor License No: GSHEAC *939RK
DESCRIPTION OF WORK:
DUCT MODIFICATIONS OF EXISTING TENANT SPACE
Value of Mechanical: $11,500.00
Type of Fire Protection:
CitAbf Tukwila
Furnace: <100K BTU
>100K BTU
Floor Furnace
Suspended/Wall/Floor Mounted Heater
Appliance Vent
Repair or Addition to Heat/Refrig /Cooling System....
Air Handling Unit <10,000 CFM
>10,000 CFM
Evaporator Cooler
Ventilation Fan connected to single duct
Ventilation System
Hood and Duct
Incinerator: Domestic
Commercial/Industrial
doc: IMC -10/06
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 -431 -3665
Web site: http: / /www.ci.tukwila.wa.us
MECHANICAL PERMIT
EQUIPMENT TYPE AND QUANTITY
0
0
0
0
0
0
0
0
0
0
0
0
0
0
* *continued on next page **
•
Permit Number:
Issue Date:
Permit Expires On:
Phone: 360 - 794 -7306
Phone: 360 - 794 -7306
Expiration Date: 07/18/2009
M08 -238
10/02/2008
03/31/2009
Fees Collected: $305.00
International Mechanical Code Edition: 2006
Boiler Compressor:
0 -3 HP/100,000 BTU 0
3 -15 HP /500,000 BTU 0
15 -30 HP /1,000,000 BTU.. 0
30 -50 HP /1,750,000 BTU.. 0
50+ HP /1,750,000 BTU 0
Fire Damper 0
Diffuser 14
Thermostat 1
Wood/Gas Stove 0
Water Heater 0
Emergency Generator 0
Other Mechanical Equipment 0
M08 -238 Printed: 10 -02 -2008
Permit Center Authorized Signature:
•
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206- 431 -3670
Fax: 206 - 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
•
Permit Number: M08 -238
Issue Date: 10/02/2008
Permit Expires On: 03/31/2009
Date: t o f
I hereby certify that I have read and -x. . ' ed t permit and know the same to be true and correct. All provisions of law and ordinances
governing this work will be complie • wit , whether specified herein or not.
The granting of this permit does not pres e to give authority to violate or cancel the provisions of any other state or local laws regulating
construction or the performance of work. I am authorized to sign and obtain this mechanical permit.
Signature: —2-
Print Name: A r f
This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended
or abandoned for a period of 180 days from the last inspection.
doc: IMC -10/06
Date: l A -Ci
M08 -238 Printed: 10 -02 -2008
•
City of Tukwila
Parcel No.: 2623049079
Address: 17364 SOUTHCENTER PY TUKW
Suite No:
Tenant: BEST BUY
1: ** *BUILDING DEPARTMENT CONDITIONS * **
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 - 431 -3665
Web site: http://www.ci.tukwila.wa.us
PERMIT CONDITIONS
•
Permit Number: M08 -238
Status: ISSUED
Applied Date: 09/23/2008
Issue Date: 10/02/2008
2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the
Building Official.
3: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to
start of any construction. These documents shall be maintained and made available until final inspection approval is
granted.
4: All construction shall be done in conformance with the approved plans and the requirements of the International
Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code.
5: Ventilation is required for all new rooms and spaces of new or existing buildings and shall be in conformance with the
International Building Code and the Washington State Ventilation and Indoor Air Quality Code.
6: All plumbing and gas piping work shall be inspected and approved under a separate permit issued by the Cityof Tukwila
Permit Center.
7: All electrical work shall be inspected and approved under a separate permit issued by the City of Tukwila Building
Department (206- 431 - 3670).
8: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of,
any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits
presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila
shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the
Building Official from requiring the correction of errors in the construction documents and other data.
doc: Cond - 10/06
* * continued on next page **
M08 -238 Printed: 10 -02 -2008
Signature:
Print Name:
doc: Cond -10/06
•
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 - 431 -3665
Web site: http: / /www.ci.tukwila.wa.us
I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and
this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provision of any other work
construction or the performance of work.
Date:
/ 64 � a -��
ordinances governing
or local laws regulating
M08 -238 Printed: 10 -02 -2008
Site Address: t 73 c-' P
P "rR- 1 e-4-‘
Mailing Address: .S Md Zn
E -Mail Address: C 1tfie - Gds
Name:
CITY OF TUKWILA
Community Development Department
Public Works Department
Permit Center
6300 Southcenter Blvd., Suite 100
Tukwila, WA 98188
htip://www.ci.iukwila.wo.us
Q: \Applications\Fmms- Applications On Line13-2006 - Permit Application.doc
Revised: 9 -2006
bh
:Building PPermit No.
Mechanical'Permit No. ra
tlurnbirig/Gas Permit No.
Public Works Permit No.
Project No.
(For office use only)
Applications and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or by fax.
* *Please Print **
King Co Assessor's Tax No.: 2 - `O 7 7
Suite Number:
Tenant Name: be � P34,
Property Owners Name:
Mailing Address:
City
New Tenant:
Fax Number: 3 _7
State
State
State
Floor:
Yes
Zip
CONTACT PERSON - who do we contact when your permit is ready to be issued
Day Telephone: 3 6n — 7 9 ( /-730‘,
City State Zip
49 -3Y3a,
;GENERAL CONTRACT,QR INFORIVIAT:ION
;,(contractor Informat�ontfor Mechanical (pg 4) for Plumbing: and. Gas. Piping (pg 5))
Company Name:
Mailing Address:
Zip
City
Contact Person: Day Telephone:
E -Mail Address: Fax Number:
Contractor Registration Number: Expiration Date:
Company Name:
Mailing Address:
City
Contact Person: Day Telephone:
E -Mail Address: Fax Number:
0
ARCHITECT OF RECORD - All plans must be wet stamped by Architect of Record
Zip
``ENGINEER OF:RECORD v All plansmustbe wet stamped by Engineer of Record
Company Name:
Mailing Address:
City State Zip
Contact Person: _ Day Telephone:
E -Mail Address: Fax Number:
Page 1 of 6
Unit Type:
Qty
Unit Type:
Qty
Unit Type:
Qty
Boiler /Compressor:
Qty
Furnace <100K BTU
Air Handling Unit >10,000
CFM
Fire Damper
0 -3 HP /100,000 BTU
Furnace >100K BTU
Evaporator Cooler
Diffuser
�
1
3 -15 HP /500,000 BTU
Floor Furnace
Ventilation Fan Connected
to Single Duct
Thermostat
I
15-30 HP /1,000,000 BTU
Suspended/Wall/Floor
Mounted Heater
Ventilation System
Wood/Gas Stove
30 -50 HP /1,750,000 BTU
Appliance Vent
Hood and Duct
Emergency
Generator
50+ HP /1,750,000 BTU
Repair or Addition to
Heat/Refrig/Cooling
System
Incinerator - Domestic
Other Mechanical
Equipment
Air Handling Unit
<10,000 CFM
Incinerator — Comm /Ind
•
MECHANICAL PERMIT INFORMATION - 206- 431 -3670
MECHANICAL CONTRACTOR ,nIN,, FOR ATION /
Company Name: `�� � >✓t Ca° � 0/73
City
Day Telephone:
1 Fax Number: 3 "Z1 - 3 ?3 -�
Contractor Registration Number: &n14 l E . ' + ( 9 -3 R K Expiration Date: � -is'-0 /
Mailing Address: -..5
Contact Person: r r 4-e.
E -Mail Address: RV') isz 3-s 64%, '1.st.. cc) i
to
Valuation of Mechanical work (contractor's bid price): $ "SOO _ MM
Scope of Work (please provide detailed information): D CA- <I4' W1ocT- fG��1d1A- r"'
Use: Residential: New .... ❑ Replacement .... ❑
Commercial: New .... ❑ Replacement ....X
1_,A4 r4 7c
3�-� - "l4
State Zip
LI^13ab
Fuel Type: Electric ❑ Gas .... Other:
Indicate type of mechanical work being installed and the quantity below:
Q. Applications\Forms- Applications On Line' -2006 - Permit Application.doc
Revised. 9 -2006
bh
Page 4 of!
PE1I IIT APPLICATION NOTES – Applicable to all permits in this application
Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject
to possible revision by the Permit Center to comply with current fee schedules.
Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation.
Building and Mechanical Permit
The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each The extension shall be
requested in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition).
Plumbing Permit
The Building Official may grant one extension of time for an additional period not exceeding 180 days. The extension shall be requested
in writing and justifiable cause demonstrated. Section 103.4.3 Uniform Plumbing Code (current edition).
I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER
PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT.
BUILDING OWNER OR AUTHORIZED AGENT:
Signature:
Print Name: 7't h 1- cv-i-t -te
Mailing Address: , 5 -3 -- 1
Date Application Expires:
-.,1 7
Date Application Accepted: ct
Q:\Applications\Forms- Applications On Line13-2006 - Permit Application.doc
Revised: 9 -2006
bit
n nf-c
City
Day Telephone:
Date:_ _ 4-
3 6.4-79 9 - 730,4
State Zip
Staff Initials:
Page 6 of 6
Payee: G & S HEATING
ACCOUNT ITEM LIST:
Description
tlnr.: Rarpint -(1R
MECHANICAL - NONRES
PLAN CHECK - NONRES
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206 - 431 -3670
Fax: 206 -431 -3665
Web site: http: / /www.ci.tukwila.wa.us
Parcel No.: 2623049079 Permit Number: M08 -238
Address: 17364 SOUTHCENTER PY TUKW Status: PENDING
Suite No: Applied Date: 09/23/2008
Applicant: BEST BUY Issue Date:
Receipt No.: R08 -03329 Payment Amount: $305.00
Initials: WER Payment Date: 09/23/2008 10:00 AM
User ID: 1655 Balance: $0.00
TRANSACTION LIST:
Type Method Descriptio Amount
Payment Check 5342 305.00
RECEIPT
Account Code Current Pmts
000.322.102.00.0 244.00
000/345.830 61.00
Total: $305.00
- ' 1 T r07 T '1-r
Printart 09 -23- 9(1(18
Proj
... --\
B2t(l
Type of Inspection: \
.
Add
173/
561 1 4A
Date Called:
v f CI
Special Instructions:
Date I I 1 _ /OLCI
(0
ster:
Requester:
P ne No:
h 1,7 - 57-)e--(-37-_2_
INSPECTION RECORD ,fin
Retain a copy with permit 1''� 2P
INSPECT NO. PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -361'0
Approved per applicable codes. Corrections required prior to approval.
COMMENTS:
i i?e/e 10 -f i o>1b /f kitn
r /
.00 REINSPECTION EE REQUIRED. Pri ' r to inspection, fee must be
p d at 6300 Southcenter Blvd., Suite 100. all to schedule reinspection.
R c tNo.:
'Date:
Project; . _. . �
d es t gJ�
Type of Inspect
10 J Inspect
An,
Address:
Date Called:
Special Instructions:
D to Wanted:
0—
b �/�a.m:
) 1 i a p.m.
Requester:
Phone No:
Z/
INSPECTION RECORD
Retain a copy with permit
PERMIT NO.
INSPECTION NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670
Approved per applicable codes. Corrections required prior to approval. •
COMMENTS:
Inspector:
Date: i O .....
n $60.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection.
Receipt No.:
'Date:
Project:
/3 -( Cr
r j L..
Type of Inspectiob:
12 d... i1 l'l /4 'r .:"
t
Address:
r I . 3 o 1
/
S itIA. = w , y
Date Called:
i
Special Instructions:
Date Wanted:
� ()— 3 .[ag
; amt.
p:m.
Requester:
Phone No:
4 2 5 - sd ,' — o�sz ---
WIT NO.
CITY OF TUKWILA BUILDING DIVISION le,
6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670
INSPECTION NO.
INSPECTION RECORD
Retain a copy with permit
Nto - 23 e
Approved per applicable codes. Corrections required prior to approval.
COMMENTS:
Inspect;:
Date;
❑ $60.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection.
Receipt No.:
Date:
3
zeL
DEPARTMENT
Building Division
Public Works l l
Complete
Comments:
Please Route
41 ERMIT COORD COPY o
PLAN REVIEW /ROUTING SLIP
ACTIVITY NUMBER: M08 -238 DATE: 09 -23 -08
PROJECT NAME: BEST BUY
SITE ADDRESS: 17364 SOUTHCENTER PY
X Original Plan Submittal Response to Incomplete Letter #
Response to Correction Letter #
Revision # After Permit Issued
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
Documents /routing slip.doc
2 -28 -02
Flre Prevention
Structural
Incomplete
.III 141a. R4'-0
Permit Center Use Only
INCOMPLETE LETTER MAILED:
Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
LETTER OF COMPLETENESS MAILED:
TUES/THURS RO TING:
REVIEWER'S INITIALS:
Structural Review Required
APPROVALS OR CORRECTIONS:
Approved ❑ Approved with Conditions
Notation:
REVIEWER'S INITIALS:
u
CI
n Permit Coordinator
DUE DATE: 09 -5-08
No further Review Required
DATE:
DUE DATE: 10 -23 -08
DATE:
Planning Division
Not Applicable
n
Not Approved (attach comments) ❑
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
Bond
Bond
Company
Name
Bond
Account
Number
Effective
Date
Expiration
Date
Cancel
Date
Impaired
Date
Bond
Amount
Received
Date
6
CBIC
SA1718
04/04/2002
Until
Cancelled
$12,000.00
02/11/2002
5
MID
CENTURY
INS CO
697016630
07/17/2001
Until
Cancelled
09/08/2002
$6,000.00
08/12/2002
4
CBIC
SA1718
04/04/199804/04
/2002
$6,000.00
04/04/1998
3
CBIC
SA1718
04/04/199604/04
/1998
$6,000.00
2
TIG
SPECIALTY
INS CO
AIC324925604
/04/199204/04/1996
$6,000.00
1
NEW
SOUTH
INS CO
112875
04/04/198604/04
/1992
$6,000.00
Name
Role
Effective Date
Expiration Date
THOMPSON, ROGER W
PRESIDENT
12/12/2007
Untitled Page
General /Specialty Contractor
A business registered as a construction contractor with Lttl to perform construction work
within the scope of its specialty. A General or Specialty construction Contractor must
maintain a surety bond or assignment of account and carry general liability insurance.
Business and Licensing Information
Name
Phone
Address
Suite /Apt.
City
State
Zip
G a S HEATING
COOLING /ELEC INC
3607947306
500 E MAIN ST
MONROE
WA
98272
County SNOHOMISH
Business Type CORPORATION
Parent
Company
UBI No.
Status
License No.
License Type
Effective Date
Expiration Date
Suspend Date
Previous
License
Next License
Associated
License
Specialty 1
Specialty 2
600407222
ACTIVE
GSHEAC *939RK
CONSTRUCTION
CONTRACTOR
12/12/2007
7/18/2009
GSHEAC *930MJ
GENERAL
UNUSED
Business Owner Information
•
•
Bond Information
https: / /fortress.wa. gov /lni/bbip/Detail. aspx ?License= GSHEAC* 939RK
Page 1 of 3
10/02/2008
AIR DEVICE ABBREVIATIONS
TYPE
DEVICE DESIGNATOR - 7- NECK SIZE
A 10z
-17 2'WL......_
LAY - CEILING - MOUNTED
SQUARE SUPPLY DIFFUSER:
STEEL CONSTRUCTION
INCLUDE OPPOSED BLADE DAMPER
COORDINATE COLOR WITH ARCHITECT
THUS, MODEL TMS OR APPROVED EQUAL
,.
S
- DAMPER
C.F.M.
4.
T YPE '
5.
DEVICE DESIGNATOR - , GRILLE SIZE
. Q=.2u2.4.. „ „
APPROX. C.F.M.
ril
CEILING- MOUNTED RERJRN AIR GRILLE:
ALUMINUM CORE WITH p" x p" SQUARES,
COORDINATE COLOR WITH ARCHITECT
TIM, MODEL 50F OR APPROVED EQUAL
13 EXISTING RTU -3X, SHALL REMAIN. PERFORM THE FOLLOWING:
- REPLACE FAN BELTS.
- PRESSURE WASH COOLING COILS,
- WASH DOWN AND VACUUM TOTAL CABINET (INSIDE).
- REPLACE ALTERS WITH FARR 30/30 ALTERS.
- CHECK REFRIGERANT CHARGE AND FOR LEAKS, REPLACE REFRIGERANT AS
NECESSARY.
- INSPECT HEAT EXCHANGER. REPORT ANY DAMAGE TO OWNER.
- TEST SMOKE DETECTOR, AND REPLACE IF NOT OPERATIONAL.
- VERIFY OPERATION OF EACH COMPONENT OF THE CONTROL SYSTEM.
- COMB CONDENSER COILS.
TYPE 'D'
DEVICE DESIGNATOR -\\ / GRILLE SIZE
,, t,
SIDE WALL - MOUNTED SUPPLY AIR GRILLE:
STEEL FRAME AND DOUBLE DEFLECTION
BLADES PARALLEL TO LONG DIMENSION.
INCLUDE OPPOSED BLADE DAMPER
COORDINATE COLOR WITH ARCHITECT
TTTUS, MODEL 300RL OR APPROVED EQUAL
'''-- DAMPER �*- ` APPROX. C.F.M.
TYPE r
DEVICE DESIGNATOR GRILLE SIZE
SIDE WALL - MOUNTED RETURN AIR REGISTER:
STEEL FRAME AND STREAMLINED 35c AXED
DEFLECTION WITH f' SPACING BLADES
PARALLEL TO LONG DIMENSION.
COORDINATE COLOR WITH ARCHITECT
TITUS, MODEL 350RL OR APPROVED EQUAL
'� - APPROX. C.F.M.
GENERAL NOTES:
1.
MOUNT ALL EXPOSED DUCTWORK AS HIGH AS POSSIBLE THROUGHOUT ENURE SPACE,
UNLESS OTHERWISE SPECIFIED. DUCTWORK SHALL BE MOUNTED IN JOIST SPACE, OR
RUN THROUGH JOIST WEB WHEREVER POSSIBLE. DUCT BELOW JOISTS SHALL BE
MOUNTED DIRECTLY BELOW JOIST FLANGE. ALL NEW DUCTS SHALL BE INSTALLED WITH
SEISMIC BRACING, AS REQUIRED BY LOCAL CODE.
2.
RELOCATE FIRE SPRINKLER HEADS AS REQUIRED FOR NEW UGHTS, DIFFUSERS, WALLS
AND CEILINGS. PLAN SHALL BE SUBMII1hu BY FIRE SPRINKLER CONTRACTOR.
3,
VERIFY EXISTING ROOFTOP UNIT IS IN GOOD WORKING CONDITION. VERIFY EXACT
LOCATION AND ORIENTATION OF ROOFTOP UNIT PRIOR TO BID. CONTACT ENGINEER WITH
ANY PROBLEMS.
4.
MECHANICAL. GRILLES AND DIFFUSERS IN SUSPENDED CEILING SHALL BE CONNECTED TO
ONE (1) VERTICAL 12 GA. WIRE ATTACHED TO OPPOSING CORNERS ALONG THE
DIAGONAL., WIRE MAY BE SLACK. PROVIDE PERIMETER VERTICAL WIRE 8" OUT FROM
WALL
5.
MECHANICAL INSTALLATION & SERVICE WORK SHALL BE COMPLETE BY SUBSTANTIAL
COMPLETION. CONDUCT TEST & BALANCE DURING TIME OF FIXTURING. G.C. SHALL
COORDINATE COMPLETION OF WORK THAT HAS IMPACT ON 1LSI & BALANCE RESULTS
(I.E. WALLS; DROP CEILING; DOORS; ETC.)
HUMIDIFICATION SPECIFICATION:
1.
THE HUMIDIFIER SHALL BE A SELF - CONTAINED ELECTRODE STEAM HUMIDIFIER
COMPLETE WTIH THE INTEGRAL ELECTRONIC CONTROLLER, WALL HUMIDISTAT, AND
BUILT -ON BLOWER PACK.
2.
UNIT TO INCLUDE STATUS UGHTS, AUTOMATIC FILL, AUTOMATIC DRAIN, DISPOSABLE
CYLINDER, AND SAFETY CONTROLS.
3.
CONTRACTOR TO PROVIDE A CITY - APPROVED SPRING-WADED DOUBLE BALL CHECK
VALVE ON THE POTABLE WATER INLET WHERE REQUIRED.
4 .
PROVIDE ALL NECESSARY SHUT-OFF VANES.
KEYED NOTES:
0 CONTRACTOR TO PROVIDE OPPOSED BLADE DAMPER IN SUPPLY DROP FROM MU
BEFORE SUPPLY AIR DROP BOX; CONICAL BRANCH TAKEOFF FOR MUSIC ROOM
SPACE IN SUPPLY DROP UPSTREAM OF OPPOSED BLADE DAMPER.
® BLOCK ALL 4 SIDES OF EXISTING SUPPLY DROP BOX DIFFUSER. CONNECT NEW
DUCTWORK AS SHOWN.
0 RELOCATE TEMPERATURE SENSOR NEXT TO LIGHT SWITCH 0 5' A.F.F. IN DRUM RM
(RM# 162). VERIFY THAT SENSOR IS IN GOOD WORKING CONDITION. REPLACE AS
NECESSARY WITH SENSOR THAT IS COMPATIBLE WITH EXISTING ENERGY MANAGEMENT
SYSTEM.
® SPRINKLER PIPING IN THIS AREA SHALL BE MODIFIED TO ADD SPRINKLER HEADS AT
THE SUSPENDED CEILING. PLAN SHALL BE SUBMITTED BY ARE SPRINKLER
CONTRACTOR.
@ 20/20 TYPE T. GRILLE (2 THUS) CONNECTED TO 20/20 TRANSFER DUCT ALLOWING
AIR BACK TO UNIT ABOVE SALES AREA . MOUNT AS HIGH AS POSSIBLE.
® ROTATE REGISTER TAKEOFF 30' FROM HORIZONTAL, SO GRILLE ANGLES TOWARD
FLOOR.
® CONTRACTOR SHALL INSTALL HUMIDIFIER IN ACCESSIBLE LOCATION. DOMESTIC
WATER CONNECTION SHALL BE MADE TO CLOSEST ADEQUATELY SIZED WATER UNE.
HUMIDIFIER SHAD. BE MOUNTED HIGH ENOUGH FOR PROPER DRAINAGE TO MOP
SINK.
® HUMIDIFIER SHALL BE INSTALLED TO CONTROL HUMIDIFY IN ACOUSTIC RM (164).
® MECHANICAL CONTRACTOR SHALL LOCATE SUPPLY DIFFUSERS AS HIGH AS POSSIBLE.
10 MECHANICAL CONTRACTOR SHALL INSTALL DUCTWORK AS HIGH AS POSSIBLE.
COORDINATE PAINT COLOR WITH ARCHITECT.
® ACOUSTICALLY UNED ELBOWS SHALL BE INSTALLED ABOVE RETURN GRILLES TO
PREVENT TRANSMISSION OF NOISE FROM ROOM. REFER TO RETURN AIR BOOT
DETAIL
2 CONTRACTOR SHALL MOUNT THE HC -1 UNIT APPROXIMATELY 8' -O" AFF ON THE
FRONT INSIDE WALL OF THE ACOUSTIC ROOM. THE HC -1 UNIT SHALL BE MOUNTED SO
IT IS BELOW THE ACOUSTIC ROOM DIFFUSER. COORDINATE HC -1 LOCATION WITH
ARCHITECTURAL PLANS.
13 EXISTING RTU -3X, SHALL REMAIN. PERFORM THE FOLLOWING:
- REPLACE FAN BELTS.
- PRESSURE WASH COOLING COILS,
- WASH DOWN AND VACUUM TOTAL CABINET (INSIDE).
- REPLACE ALTERS WITH FARR 30/30 ALTERS.
- CHECK REFRIGERANT CHARGE AND FOR LEAKS, REPLACE REFRIGERANT AS
NECESSARY.
- INSPECT HEAT EXCHANGER. REPORT ANY DAMAGE TO OWNER.
- TEST SMOKE DETECTOR, AND REPLACE IF NOT OPERATIONAL.
- VERIFY OPERATION OF EACH COMPONENT OF THE CONTROL SYSTEM.
- COMB CONDENSER COILS.
14 MECHANICAL CONTRACTOR SHALL INSTALL DUCTWORK AS CLOSE TO WALL AS POSSIBLE.
1
DtWou
RETURN OR TRANSFER
AIR GRILLE, PER PLAN
1 Return Air Boot Detail
SaFiE Not to
Or
At0y6 e&I (A L-11 pi/h
pw jet wig he a p1414444k. Ooviefd
►�1 � ri ny , pi pirt) 6-rv: -k b.c plati44444_
9m d wb GomM (4 4i19tc 6c/vi lei w� nAvirM ats
Wpused pla,wnt,
NOTES:
1)'X' DIMENSION IS SMALLER DIMENSION OF GRILLE AND DUCT
2)UNE fillIBUNTERIOR SURFACE OF BOOT WITH 1/2'
CLOSED CELL, PLENUM RATED, INSULATION.
3) WHERE A BOOT EXTENDS THROUGH A FULL HEIGHT WALL (REFER
TO PLANS, INCL ARCHITECTURAL), CONTRACTOR SHALL ENSURE
THAT OPENING THROUGH WALL FOR DUCT IS SEALED AFTER
INSTALLATION OF BOOT.
4) VERIFY ALL CEILING TYPES WITH ARCHITECTURAL. FOR PROPER
SELECTION OF MOUNTING FRAMES.
Y
Xl2
r
00
w -1
HUMIDIFIER SCHEDULE
MARK
CP -1
UN
PUMP SCHEDULE
SERVES
HC -1
MANUFACTURER
NORTEC
MANUFACTURER
BECKEIT
E 1 PROVIDE UNIT WITH THERMAL OVERLOAD PROTECTION.
WALL OF MUSICAL.
INSTRUMENT ROOM
CP -1 (IF REQUIRED)
.._...._.... "...._._.....tee ... ........ .... . rardmilmme __...._..., r....._.:..
SERIES
RESDELUX
O UNIT SHALL BE INSTALLED BY H.VAC. CONTRACTOR PER MANUFACTURER'S REQUIREMENTS.
I UNIT SHALL START / STOP VIA HUMIDISTAT IN ACOUSTIC ROOM (1 64)
• HUMIDISTAT REQUIRED: NORTEC PART #2520259 w STAT WALL MOUNTED ON /OFF CONTROL WITH DIGITAL DISPLAY'
MODEL
CB501ULHT
HVAC Plan View
scALE: site• ' -o'
CONDENSATE. INCLUDE RECEPTOR WITH AIRS
GAP, SLOPE PIPING TO PUMP CP -1. CP -1
SHALL BE MOUNTED BESIDE HC -1.
COORDINATE LOCATION WITH ELECTRICAL
CONTRACTOR FOR REQUIRED OUTLET. ROUTE
PIPING UP TO JOIST SPACE, THEN SLOPE
ALONG ENTIRE LENGTH TO JANITORS MOP SINK
OR FLOOR DRAIN.
TYPE
COLD WATER CONNECTION TO UNIT.- -
INCLUDE BACKFLOW PREVENTION VALVE
AND SHUT --OFF,
GPM /H
t4'o
396 GPH 0 1O` HEAD
NWT)
FLP./W
1/5TH
PROVIDE UNIT WITH SAFETY SWITCH (HIGH LEVEL ALARM).
BLOWER PACK
FASTEN UNIT TO WALL,
PER !DM (SEISMIC)
COLx
R2f.alIREMENTS.
AT RROVEIJ CHECK VALVE
2 Humidifier Installation Detail
SCALE: Not to Scale
s
00
{
MOTOR
MAX R.P.M. VOLTS /PH
115/1
L.?V
HC -1
REMARKS
INTERLOCK SAFETY SWITCH WITH A FILL VALVE
ON HUMIDIFIER. (24 VOLT)
SEPARATED PERMIT
REQUIRED
Mechanical
Eirt E1eCtriCal
Gas g Gas Piping
City of Tukw
BUILDING DIVISION
FILE COPY
Permit No
Date:
REVISIONS
No changes shall be made to the scope
of work without prior approval of
Tukwila Building Division.
NOTE: Revisions will require a new plan submittal
and may include additional plan review fees.
Plar review approval Is subject to errors and omissions.
Approval of construction documents does not authorize
the violation of any adopted code or ordinance. Receipt
of approved Field Copy and conditions is ackrnowicdc
By
City of Tukwila
BUILDING DIVISION
RECEIVED
SEP2320
PERMIT CENTER
%1O8 j3�
VQ_ FT. CALCS
2e44 SF
2MM4 SF
CONCEPT:
.:
MI
CONCEPT PATE:
03 -1a - 0S
T5TORE NILIMEBERI
441
II.V.A.C. PLAN &
DETAILS
cl)
tea z
• at 01
• Z
11.1
▪ a
0 co
▪ O
1"
RECEIVED
JUL 2 4 2008
'DS CONSTRUCTION, INC.
'TIT
5T
SECTION 15000 - GENERAL PROVISIONS
PART 1 GENERAL
1.1 WORK INCLUDED
A. THIS SECTION OF THE SPECIFICATION INCLUDES THE ADMINISTRATIVE AND GENERAL REQUIREMENTS WHICH ARE APPUCABLE TO, AND BECOME A PART OF, ALL OF TIME FOLLOWING SECTIONS OF THIS SPECIFICATION.
1.2 PERFORMANCE
A. MECHANICAL CONTRACTOR SHALL PERFORM All WORK SPECIFIED, INDICATED AND REQUIRED UNLESS OTHERWISE NOTED, INCLUDING FINAL CONNECTIONS, IN A WORKMANLIKE MANNER USING WORKERS SKILLED AND EXPERIENCED IN
THE TRADE
1.3 SITE EXAMINATION
A. EXAMINE SITE BEFORE BIDDING. CLAIM NO EXTRAS RESULTING FROM LACK OF KNOWLEDGE OF SITE CONDITIONS. IF SITE CONDITIONS REQUIRE MOD1FICA1ION OF THE SYSTEMS INDICATED IN THESE DOCUMENTS, SO ADVISE
ENGINEER, AND IF ACCEPTED BY ENGINEER, INCLUDE COST OF SUCH MODIFICATIONS IN BID.
1.4 JOBSITE CONDITIONS
A. CONTRACTOR SHALL ACCEPT SOLE AND COMPLETE RESPONSIBILITY FOR CONDITIONS OF THE JOBSIIE, INCLUDING SAFETY OF ALL PERSONS AND PROPERTY DURING PERFORMANCE OF THE WORK.
1.5 FULL FUNCTION
A, PROVIDE MINOR ITEMS NECESSARY FOR A COMPLETE AND FULLY FUNCTIONAL INSTALLATION.
1.6 PERMITS, UCENSES, AND FEES
A. ADMINISTRATION: PROVIDE EVIDENCE OF UCENSURE, BONDING, AND INSURANCE, AND PERFORM OTHER ADMINISTRATIVE FUNCTIONS, AS REQUIRED.
PERMITS: PROCURE AND PAY FOR ALL REQUIRED PERMITS AND SERVICE CHARGES.
1,7 COORDINATION OF WORK
A, COORDINATE ALL WORK WITH OTHER TRADES. PLAN AND COORDINATE WORK WITH THE WORK OF OTHER TRADES. ANY WORK THAT MUST BE REINSTALLED BECAUSE OF CONFLICT WITH OTHER TRADES SHALL BE REINSTALLED AT
NO COST TO THE OWNER.
1.10 EQUIPMENT SUBSTITUTIONS
A. SUBSTITUTIONS ARE ALLOWED BY PRIOR APPROVAL BY THE ENGINEER /OWNER ONLY CONTRACTOR SHALL BE RESPONSIBLE FOR ANY CHARGES OR ADDITIONAL WORK REQUIRED DUE TO SUBSTITUTION OF MECHANICAL EQUIPMENT.
THIS INCLUDES OTHER TRADES.
1.11 REFERENCE STANDARDS
A. COMPLY WITH APPLICABLE STANDARDS OF NFPA, AN UL., ASHRAE, AND %TACNA, EXCEPT AS SUPERSEDED BY LOCAL AUTHORITY. CONFORM MTH CONTRACT DOCUMENTS WHERE THEY EXCEED CODE MINIMUM REQUIREMENTS.
1.12 LOCAL REQUIREMENTS
A, COMPLY WITH THE REQUIREMENTS OF APPUCABLE CODES, OWNER, SERVING UTIUTIES, AND THE LOCAL AUTHORITY HAVING JURISDICTION. SECURE APPROVAL OF INSTALLATION BY OWNER, LOCAL AUTHORITY, AND OTHER AS
REQUIRED.
1.13 MATERIAL AND EQUIPMENT
A PROVIDE NEW UL LISTED, COMMERCIAL GRADE MATERIALS, DEVICES, EQUIPMENT, AND FIXTURES SUITABLE FOR ENVIRONMENT. REUSE EXISTING ONLY WHEN COMPLIANT WITH THE CONTRACT DOCUMENTS, IN GOOD CONDITION, AND
APPROVED BY THE ENGINEER. PRODUCTS REQUIRING ELECTRICAL CONNECTION SHALL HAVE MAJOR COMPONENTS LISTED AND CLASSIFIED BY UNDERWRITERS LABORATORIES INC., AS SUITABLE FOR THE PURPOSE SPECIFIED AND
INDICATED. COMPLETE UNIT SHALL BE ETL OR UL LISTED.
1.15 SHOP DRAWING /SUBMITTALS
A. BEFORE ORDERING EQUIPMENT AND MATERIALS, SUBMIT NOT LESS THAN FIVE CERTIFIED COPIED OF ALL SHOP AND EQUIPMENT DRAWINGS FOR ENGINEER'S REVIEW, WHO WILT. RETAIN TWO COPIES. ONLY FURNISH SYSTEMS AND
EQUIPMENT IN COMPLIANCE WITH ACCEPTED SHOP DRAWINGS. SHOP DRAWINGS SHALL INCLUDE RATED CAPACITIES, WEIGHTS, ACCESSORIES, ELECTRICAL NAMEPLATE DATA, AND WIRING DIAGRAMS. INDICATE ASSEMBLY, REQUIRED
CLEARANCES, AND LOCATIONS AND SIZES OF FIELD CONNECTIONS.
1.16 ENVIRONMENTAL REQUIREMENTS
A. DO NOT OPERATE AIR MOVING EQUIPMENT UNTIL DUCTWORK IS (LEAN, FILTERS ARE IN PLACE, BEARINGS LUBRICATED, AND FAN HAS BEEN TEST RUN UNDER OBSERVATION.
1.17 WARRANTY
A. SUBMIT MANUFACTURERS WARRANTY AND ENSURE FORMS HAVE BEEN FILLED OUT IN OWNERS NAME AND REGISTERED WITH MANUFACTURER.
1.18 QUALITY ASSURANCE
A. COMPANY SPECIALIZING IN MANUFACTURING NE PRODUCTS SPECIFIED IN THIS SECTION WITH MINIMUM THREE YEARS EX ERIENCE
1.19 INSTALLATION
A. INSTALL ALL MATERIALS, EQUIPMENT, AND SYSTEMS IN FULL ACCORD WITH MANUFACTURER'S INSTRUCTION.
1.20 LAYOUT OF WORK
A. INSTALL ALL PIPING AND DUCTWORK TO PRESENT A NEAT AND ORDERLY APPEARANCE, RUN ALL ONES PARALLEL WITH BUILDING CONSTRUCTION. MAINTAIN HEADROOM AND EQUIPMENT CLEARANCE, AND GRADIENT WHERE
REQUIRED. ALLOW FOR EXPANSION AND CONTRACTION.
1.21 ACCESS DOORS
A. PROVIDE ACCESS DOORS OR PANELS FOR ALL VALVES, CLEA.NOUTS, DAMPERS, _CONTROLS, DEVICES, AND OTHER ITEMS REQUIRING INSPECTION OR MAINTENANCE. ACCESS PANELS SERVING HVAC COMPONENTS SHALL BE
12- INCHES MINIMUM OR LARGER TO PROVIDE SUFFICIENT WORKING CLEARANCE FOR COMPONENT BONG ACCESSED.
1.22 COMMISSIONING
A. THOROUGHLY TEST AND DEMONSTRATE PROPER OPERATION OF ALL SYSTEMS AND EQUIPMENT FURNISHED OR INSTALLED UNDER THIS CONTRACT. WHERE START -UP INSTRUCTIONS ARE PROVIDED WITH EQUIPMENT, CONTRACTOR
SHALL PROVIDE EVIDENCE THAT EQUIPMENT HAS BEEN STARTED UP ACCORDING TO FACTORY DIRECTIONS.
1.24 WARRANTY
A. UNCONDITIONALLY WARRANT ALL WORK TO BE FREE OF DEFECTS IN MATERIALS AND WORKMANSHIP FOR ONE YEAR FROM DATE OF FINAL ACCEPTANCE, EXCEPT WARRANT AIR CONDITIONING COMPRESSORS FOR FIVE YEARS AND
GAS -FIRED HEAT EXCHANGERS FOR TEN YEARS. DURING WARRANTY PERIOD, REPAIR OR REPLACE DEFECTIVE MATERIALS EQUIPMENT OR WORKMANSHIP WITHOUT COST TO THE OWNER.
1.27 DRAWINGS ARE DIAGRAMMATIC
A. VERIFY ALL DIMENSIONS AND LENGTH, AND ADJUST EQUIPMENT, PIPE AND DUCT LOCATIONS TO AVOID CONFUCTS WITH OTHER CONSTRUCTION AND TRADES.
1.28 DOCUMENT PRIORITY
A. DRAWING INDICATIONS AND NOTATIONS SUPERSEDE THESE SPECIFICATIONS.
1.29 PROJECT REQUIREMENTS
A. REFER TO DRAWINGS FOR PARTICULAR PROJECT REQUIREMENTS, AS NOT ALL ITEMS INCLUDED IN THESE SPECIFICATIONS MAY BE REQUIRED FOR THIS PROJECT. 1.30 DOCUMENT ERRORS
A. NOTIFY THE ENGINEER OF ERRORS, DISCREPANCIES OR OMISSIONS BEFORE CONSTRUCTION OR FABRICATION OF AFFECTED WORK, OR, FAILING SUCH NOTICE, BE RESPONSIBLE FOR CORRECTING SAME WITHOUT COST TO TENANT,
ARCHITECT OR ENGINEER.
15200 - THERMAL AND ACOUSTIC INSULATION
1.1 VIBRATION ISOLATION: PROVIDE EFFECTIVE VIBRATION ISOLATION DEVICES, AND FLEXIBLE CONNECTIONS, FOR ALL MOVING MACHINERY. PROVIDE DEVICES IN ACCORDANCE WITH THE RECOMMENDATIONS IN THE ASHRAE HANDBOOK,
HVAC APPLICATIONS (LATEST EDITION), CHAPTER 'SOUND AND VIBRATION CONTROL ".
1.2 NOISE TRANSMISSION: INSTALL DUCTWORK FREE FROM CONTACT WITH STRUCTURE OR EQUIPMENT TO PREVENT NOISE TRANSMISSION.
1.3 INSULATION REQUIREMENTS: INSULATE SYSTEMS AS SPECIFIED ONLY AFTER THEY HAVE BEEN TESTED AND INSPECTED. CLEAN All SURFACES THOROUGHLY OF MOISTURE, FOREIGN MATERIAL GREASE, AND RUST, INSTALL
INSULATION CONTINUOUS THROUGH PENETRATIONS.
1.4 INSULATION HAZARDS: USE ONLY INSULATION ADHESIVES, SEALERS, AND COATINGS WITH FIRE HAZARD RATING NOT TO EXCEED 25/50/50 FLAME SPREAD, FUEL CONTRIBUTED, AND SMOKE DEVELOPED, IN ACCORDANCE WITH
UL 723 AND ASTM E84.
1.5 INSULATED CONCEALED DUCT ONLY EXTERNALLY INSULATE WIN 2 INCH THICK GLASS FIBER INSULATION WITH KRAFT FOIL VAPOR BARRIER, OWENS- CORNING, OR EQUAL.
15800 DUCTWORK AND APPURTENANCES
1.1 SHEET METAL DUCTWORK:
A. FABRICATE AND INSTALL AS RECOMMENDED IN LATL1 EDITIONS OF SMACNA HYAC DUCT CONSTRUCTION STANDARDS - METAL AND FLEXIBLE AND THE ASHRAE GUIDE AND DATA BOOK FOR SHEET METAL DUCTWORK SERVING
SUPPLY, RETURN AND EXHAUST SYSTEMS OPERATING BETWEEN -2.0 IN. -W.G. AND +2.0 IN. -W.G. MAXIMUM PRESSURE. INSTALL WHERE INDICATED ON THE PLANS. DUCT SIZES SHOWN ON THE DRAWINGS ARE NOMINAL INSIDE
CLEAR DIMENSIONS. WHERE INTERNAL INSULATION IS PROVIDED, DUCT SIZES MUST BE INCREASED APPROPRIATELY TO MAINTAIN THE INDICATED DIMENSIONS. ASSEMBLE AND INSTALL DUCTWORK IN ACCORDANCE WITH RECOGNIZED
INDUSTRY PRACTICE FOR ACHIEVING AIR TIGHT 5 PERCENT LEAKAGE AND NOISELESS (NO OBJECTIONABLE NOISE) SYSTEMS, CJIPABLE OF PERFORMING EACH INDICATED SERVICE. FURNISH ALL REQUIRED DAMPERS, TRANSITIONS, AND
CONNECTIONS TO MR TERMINALS, AND OTHER ACCESSORIES NECESSARY FOR A COMPLETE OPERATING SYSTEM.
B. FABRICATE DUCTWORK FROM GALVANIZED SHEET STEEL COMPLYING WITH ANSI/ASTM A -527, LOCKFORMING QUALITY, WITH ANSI /ASTM A -525 G90 ZINC COATING; MILL PHOSPHATIZED FOR EXPOSED LOCATIONS. MINIMUM SHEET
THICKNESS AND REINFORCING SHALL BE AS FOLLOWS:
1. DUCTS UP TO 12 WIDEST DIMENSION (OR DIAMETER): 26 GAUGE
2. DUCTS 13" TO 30 WIDEST DIMENSION: 24 GAUGE,
3. DUCTS 31" TO 54" WIDEST DIMENSION: 22 GAUGE
4. DUCTS 55" TO 84" WIDEST DIMENSION: 20 GAUGE
C. DUCT SEALANT: UNITED DUCT SEALER, OR EQUAL PROVIDE A NON - HARDENING, NON - MIGRATING MASTIC OR LIQUID ELASTIC SEALANT OF A TYPE AS RECOMMENDED BY THE MANUFACTURER SPECIFICALLY FOR SEALING JOINTS
AND SEAMS IN SHUT METAL DUCTWORK. ALL DUCTWORK SHALL HAVE SEALED LONGITUDINAL AND TRANSVERSE JOINTS. WHERE SUP AND DRIVE JOINTS ARE MADE, A SEALER SHALL BE APPLIED) OVER THE ENTIRE JOINT AFTER THE
DRIVE IS IN RACE. APPLY A SECONDARY LAYER OF SEALER AT THE CORNERS AFTER THE DRIVE ENDS ARE CRIMPED IN PLACE. ALL LONGITUDINAL SEAMS SHALL BE COVERED WITH A SEALING MASTIC. ALL SUP JOINTS SHALL BE
MADE AND COATED, THEN INSERTED INTO THE DUCT OR COLLAR AND SECURED WITH SHEET METAL SCREWS, COVER THE ENTIRE OUTER JOINT AND SCREWS WMI MASTIC. COVER JOINTS AROUND ALL SPIN -IN FITTINGS.
INTERNALLY CLEAN DUCTWORK OF DUST AND DEBRIS.
D. SUPPORT MATERIALS: EXCEPT AS OTHERWISE INDICATED, PROVIDE HOT- DIPPED GALVANIZED STEEL FASTENERS, ANCHORS, RODS, STRAPS, TRIM, AND ANGLES FOR SUPPORT OF DUCTWORK.
E. ANY SUPPLY DUCTWORK AND PLENUMS THAT ARE DESIGNED TO OPERATE AT STATIC PRESSURES GREATER THAN 0.25" Y`JG BUT LESS THAN 2" L` /G, WHICH ARE LOCATED OUTSIDE OF THE CONDITIONED SPACE OR IN RETURN
PLENUMS, SHALL HAVE JOINTS SEALED IN ACCORDANCE WITH SEAL CLASS AS DEFINED IN THE SMACNA HVAC DUCT LEAKAGE TEST MANUAL PRESSURE SENSITIVE TAPE SHALL NOT BE USED AS THE PRIMARY SEALANT WHERE SUCH
DUCTS ARE DESIGNED TO OPERATE AT STATIC PRESSURES OVER 1" WG.
1.2 DUCTWORK ACCESSORIES:
A. BALANCING DAMPERS: AIR BALANCE, INC., LOUVERS & DAMPERS, INC., RUSKIN, OR EQUAL. PROVIDE MANUAL, SINGLE OR MULTIBLADE DAMPERS, AS INDICATED AND AS CONSTRUCTED IN ACCORDANCE WITH SMACNA STANDARDS.
B. DAMPERS SHALL HAVE RIGID 2 -INCH X 1/2 INCH X 10 -GAUGE CHANNEL FRAMES, BALL OR BRONZE SLEEVE BFARIN , 1/2 INCH POLISHED STEEL AXLES, 16- GAUGE, REINFORCED, FELT -EDGED BLADES (NOT OVER 8 -INCH
WIDE) AND STOP FRAMES AROUND THE ENTIRE PERIMETER, VOLUME DAMPERS IN DUCTS LARGER THAN 12 -INCH X 6 -INCH SHALL BE THE OPPOSED BLADE TYPE. DAMPERS IN ROUND DUCTS AND DUCTS 12 -INCH X 6 -INCH AND
SMALLER SHALL BE BUTTERFLY TYPE, ROUND BUTTERFLY TYPE VOLUME DAMPERS SHALL BE 26- GAUGE, GALVANIZED STEEL THROUGH 12 -INCH DIAMETER; 24 GAUGE FOR ABOVE 12 -INCH.
C. ALL DAMPERS SHALL BE EQUIPPED WITH STANDARD QUADRANTS OF SUITABLE SIZE IN EQUIPMENT ROOMS /AREAS AND YOUNG /301A, OR EQUAL, RECESSED -TYPE IN FINISHED AREAS. PROVIDE QUADRANT LOCKING DEVICE FOR
EACH DAMPER ON ONE END OF THE SHAFT AND AN END BEARING EXTENDED QUADRANT LOCKED AND EXTENDED BEARING PLATES FOR EXTERNALLY INSULATED DUCTWORK. APPROVED MANUFACTURERS ARE VENTFABRICS, AND YOUNG
REGULATOR.
D. VOLUME DAMPERS SHALL BE PROVIDED IN ALL DUCTS TO PERMIT
SPACE AND LOCKED IN PLACE
1.3 AIR OUTLETS AND INLETS:
A. FURNISH AND INSTALL TINS, KRUEGER, OR APPROVED EQUAL AS
WITH VERTICAL BLADES AND SCREWDRIVER SLOTS OR ALLEN WRENCH
COMPLETE AND PROPER INSTALLATION IN THE TYPES OF WALLS AND
15920 TEST & BALANCE
ACCURATE BALANCING OF THE SYSTEM. THE DAMPERS SHALL BE ADJUSTED TO SATISFY THE HEATING AND VENTILATING REQUIREMENTS OF THE CONDTIIONID)
SCHEDULED. OPPOSED BLADE VOLUME DAMPERS FOR REGISTERS SHALL BE TINS SERIES AG -75, KRUEGER SERIES OBC, OR EQUAL, OPPOSED BLADE TYPES
ADJUSTMENT ACCESSIBLE THROUGH THE REGISTER. IT SHALL BE THE CONTRACTOR'S RESPONSIBILITY TO PROVIDE MISCELLANEOUS ITEMS AS NECESSARY FOR A
CEILINGS USED ON THIS PROJECT. THIS SHALL INCLUDE SUCH ITEMS AS FASTENERS, PLASTER RINGS, SUPPORTS, ETC.
1.1 WORK INCLUDED
A, MECHANICAL CONTRACTOR SHALL HIRE AN INDEPENDENT TEST & BALANCE CONTRACTOR TO PERFORM COMPLETE BALAANCING OF THE AIR AND WATER SYSTEMS IN THIS PROJECT. MECHANIC& CONTRACTOR SHALL PROVIDE TAB
CONTRACTOR WITH A COPY OF ALL SHOP DRAWINGS. T&B CONTRACTOR SHALL PROVIDE A 2 COPIES OF THE TAB REPORT TO THE ENGINEER AND OWNER (4 COPIES) UPON COMPLETION.
1.2 QUALITY ASSURANCE
A. INDEPENDENT CONTRACTOR SHALL BE CERTIFIED TO PERFORM TOTAL SYSTEM BALANCE IN ACCORDANCE WITH NEBB PROCEDURAL STANDARDS FOR TESTING, BALANCING AND ADJUSTING OF ENVIRONMENTAL SYSTEMS.
RECEIVED
SEP 232
PERMIT CENTLE
0 IT
or 0
AWL'
E
W
cT,
m
SQ. FT. CALCS
2944 SF
Totat.,
2 944
c NGI PT=
MI
CONCEPT DATE:
03-15..05
STORE NLEtR
44 I
z ea dl
at
• I , o ld
of i-
Z
U
7j
.
c c n
RECEIVED
JUL 2 4 zoo8
ISSUE DATE:
05 -1 (2 - 05
IREv. DATE
>
SPECIFICATION