Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
Permit PG08-209 - WESTFIELD SOUTHCENTER MALL - MARC ECKO CUT & SEW
MARC ECKO CUT & SEW 837 SOUTHCENTER MALL PGO82O9 Parcel No.: 6364200010 Address: Suite No: Citya If Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us PLUMBING /GAS PIPING PERMIT 837 SOUTHCENTER MALL TUKW Permit Number: Issue Date: Permit Expires On: PG08 -209 08/21/2008 02/17/2009 Tenant: Name: MARC ECHO CUT & SEW Address: 837 SOUTHCENTER MALL , TUKWILA WA Owner: Name: WESTFIELD PROPERTY TAX DEPT Address: PO BOX 130940 , CARLSBAD CA Contact Person: Name: KEVIN WENDELL Address: 100 EAST SWISSVALE AV , PITTSBURG PA Contractor: Name: J E M CONSTRUCTION INC Address: 29506 8TH AVE S , ROY, WA Contractor License No: JEMCOI *033DD Phone: Phone: 412 243 -3430 X 236 Phone: 253 843 -2765 Expiration Date: 05/12/2009 DESCRIPTION OF WORK: PLUMBING FOR NEW TI including INSTALLATION OF (1) ONE 0.5" REDUCED PRESSURE PRINCIPLE ASSEMBLY (RPPA). Value of Plumbing /Gas Piping: Fees Collected: $12,000.00 $181.00 Plumbing Bathtub or combination bath/shower Bidet Clothes washer, domestic Dental unit, cuspidor Dishwasher, domestic, with independent drain Drinking fountain or water cooler (per head) Food -waste grinder, commercial Floor drain Shower, single head trap Lavatory Wash fountain Receptor, indirect waste Sinks Urinals Water Closet Uniform Plumbing Code Edition: 2006 International Fuel Gas Code Edition: 2006 FIXTURE TYPE AND OUANTITY Plumbing (cont.) 0 Building sewer and each trailer park sewer 0 0 Rain water system - per drain (inside bldg) 0 0 Water heater and/or vent 1 0 Industrial waste treatment interceptor, including 0 its trap and vent, except for kitchen type 0 grease interceptors 0 0 Repair or alteration of water piping and/or water 1 treatment equipment 0 0 Repair or alteration of drainage or vent piping 0 1 Medical gas piping system serving (1 -5) 0 inlets /outlets for a specific gas 1 0 Medical gas piping (6 +) inlets /outlets 1 0 Gas Piping 0 Gas piping outlets (0 -5) 0 1 Gas piping outlets (6 +) 0 * *continued on next page ** doc: UPC -10/06 PG08 -209 Printed: 08 -21 -2008 City ofTukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us Permit Number: PG08 -209 Issue Date: 08/21/2008 Permit Expires On: 02/17/2009 Permit Center Authorized Signature: `k)lik Date: V -A- I -00 I hereby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances governing this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating construction or the performance of work. I am authorized to sign and obtain this plumbing /gas piping permit. Signature: Date: Gv (21 ` e Print Name: Z-LttiAA) ' This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. doc: UPC -10/06 PG08 -209 Printed: 08-21 -2008 Parcel No.: 6364200010 Address: Suite No: Tenant: ID City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us 837 SOUTHCENTER MALL TUKW MARC ECHO CUT & SEW PERMIT CONDITIONS Permit Number: Status: Applied Date: Issue Date: PG08 -209 ISSUED 07/18/2008 08/21/2008 1: ** *PLUMBING AND GAS PIPING * ** 2: No changes shall be made to applicable plans and specifications unless prior approval is obtained from the Tukwila Building Division. 3: All permits, inspection records and applicable plans shall be maintained at the job and available to the plumbing inspector. 4: All plumbing and gas piping systems shall be installed in compliance with the Uniform Plumbing Code and the Fuel Gas Code. 5: No portion of any plumbing system or gas piping shall be concealed until inspected and approved. 6: All plumbing and gas piping systems shall be tested and approved as required by the Plumbing Code and Fuel Gas Code. Tests shall be conducted in the presence of the Plumbing Inspector. It shall be the duty of the holder of the permit to make sure that the work will stand the test prescribed before giving notification that the work is ready for inspection. 7: No water, soil, or waste pipe shall be installed or permitted outside of a building or in an exterior wall unless, adequate provision is made to protect such pipe from freezing. All hot and cold water pipes installed outside the conditioned space shall be insulated to minimum R -3. 8: Plastic and copper piping running through framing members to within one (1) inch of the exposed framing shall be protected by steel nail plates not less than 18 guage. 9: Piping through concrete or masonry walls shall not be subject to any load from building construction. No plumbing piping shall be directly embedded in concrete or masonry. 10: All pipes penetrating floor /ceiling assemblies and fire - resistance rated walls or partitions shall be protected in accordance with the requirements of the building code. 11: The issuance of a permit or approval of plans and specifications shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the Plumbing Code or Fuel Gas Code or any other ordinance of the jurisdiction. 12: ** *PUBLIC WORKS DEPARTMENT CONDPI'IONS * ** 13: PROPOSED REDUCED PRESSURE PRINCIPLE ASSEMBLY (RPPA) SHALL BE INSTALLED PER MANUFACTURER'S SPECIFICATIONS. * *continued on next page ** doc: Cond -10/06 PG08 -209 Printed: 08 -21 -2008 • • City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provision of any other work construction or the performance of work. Signature: Print Name: Date: b !2-t I6, ordinances governing or local laws regulating doc: Cond -10/06 PG08 -209 Printed: 08 -21 -2008 Site Address: CITY OF TUKWILA Community Development Department Public Works Department Permit Center 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 http://www.ci.tukwila.wa.us Applications and plans must be complete in order to be accepted for plan review Applications will not be accepted through the mail or by fax. * *Please Print ** 87 King Co Assessor's Tax No.: 6 3 C4Zo oo 1(,'! (A.14-1 cis i WA+ " t 4 J MA i I Suite Number' Floor: i Tenant Name: NIA e_ C- CiAr 5 w Property Owners Name: CU x.57 F--104--0 CO K t L 9K4 -)-IO /..) New Tenant: RI Yes ❑..No Mailing Address: II 6d1 CP1 1 C s A I&L-L > City E..,4 state /o-o2-5 Zip Name: ki: ttl kk? c. N Q w t LA-P.1 Cr P,,LS Vl'l )466AeNr Day Telephone: 414-Z43-3430 it 23‘ Mailing Address:100 EAST T w'i SSi/i4t-C. Atte --Aik t P;rrst5y'ta6-k -( PA- 1 S 2—I City E -Mail Address: c Ai 0 WU- €,LA m i (re 143 ern Fax Number: 411 ` 37 I " r SSA State Zip Company Name: X13 0 Mailing Address: City Day Telephone: Fax Number: Expiration Date: Contact Person: E -Mail Address: Contractor Registration Number: Company Name: Mailing Address: CoQ. -.r- j P)d(rs -k;i `7 I l . E.-1 e, L.-io CAZ_ Ar?cHt rl i-- State Zip Contact Person: - cf f S. r'-t R Ol't K) i.J V6-1 O IJ -r )(. E -Mail Address: ✓l.'�, Company Name: Hl i+1,1.. et?, &6 6-1v el i u (- City State Zip Day 5 6 9 6 63 S 5 6 9 6 Fax Number: �0 i 7 '-' (3 5 -- 5b 99 Mailing Address: 17 50 CA pi m G tZC.G Co IA Contact Person: iv 614 ariZ•C wrfirE- tear. i—A -KE. mto 55-it d city state Zip Day Telephone: G 5 I .- 74g —1100 Fax Number: (= 5 i - 7 -s:1)370 E -Mail Address: I'S5 X14 Rc m -- 1.14t,1.--0 6-126' 'G= %N6- EZf`.i .+o(,- • CO m Q:1Applicationa\Fmms- Applications On Line'3 -2006 - Permit Application.doc Revised: 9 -2006 hh Page 1 of 6 BUILDING PERMIT INFORMATION - 206- 431 -3670 Valuation of Project (contractor's bid price): $ 15, 600 Existing Building Valuation: $ 2.3 f`i'r = (ror:�it) Scope of Work (please provide detailed information): j N r C 12.i c C.Z. TC'v 4 -r t' i i µ r c, F A ki e vic-Y Dt�l'ni5 Po cc l:U 4 p+ lh% 5C•L.riOki (Jr tfu + =jCIS; l A 6- i 1U(Z 11, 41_L Ca p GT -RkeLT CVO OF 1,/ 5TOI� F'QC= J Ti f -P r/ no Ai , /96r11 i S, /)6 G- Ye 30 { O+9irfOty of Fl is i -►E-3 4 0 Fperylt 5. PriA2 AV T1171-1 Ot- 51VC'V 4,71ttlt44N, /int "P 1/PCIAitinvtLt GF 4i $1 Will there be new rack storage? [ j Yes ❑.. No If yes, a separate permit and plan submit 1 will be required. orr'de uilding Areas in Square Footage Below Addition toi Existing Structure rior Remodel Construct IBC Type of ceupancy,per IBC our., 2"d Fli 3`d Floor Basemc M Attached Garage AI d ehed Q Covered De Uncove )eok' u PLANNING DIVISION: 4// / Single family building footprint ( a of the foundation of all structures, plus any decks over 18 hes and overhangs greater than 18 inches) *For an Accessory dwelling, pr ide the following: Lot Area (sq ft): Floor area of principal dwelling: loor area of accessory dwelling: *Provide documen ion that shows that the principal owner lives in one of the dwellings as his o er primary residence. Compact: Handicap: Number of Parking Stal rovided: Standard: Will there be a chang n use? ❑ Yes ❑ No If "yes ", explain: FIRE PROTECT1ON/HAZARDOUS MATERIALS: ® Sprinklers ] Automatic Fire Alarm ❑ None ❑ Other (specify) Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ Yes [ No If `yes', attach list of materials and storage locations on a separate 8-1/2" x 11 " paper including quantities and Material Safety Data Sheets. SEPTIC SYSTEM 44 ❑ On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health Department. Q: \4pplications\Fomis- Applications On Line'•3 -2006 - Permit Application.doc Revised: g-2006 bl, Page 2 of 6 • . • PERMIT N4 ORMATJON 206 431 367 PLUMBING AND GAS PIPING CONTRACTOR INFORMATION Company Name: (3 Q Mailing Address: City State Zip Contact Person: Day Telephone: E -Mail Address: Fax Number: Contractor Registration Number: Expiration Date: Valuation of Plumbing work (contractor's bid price): $ Z, el CO 8 Valuation of Gas Piping work (contractor's bid price): $ Scope of Work (please provide detailed information): tV " ZI re P4 xi r FIT 04.r O F R , t w De miSEj fgc_6 I.wi A sJE+a Sc'CTiom vF #j as eKis77t -'6- fiTE ZJe'( Building Use (per Int'l Building Code): Pt CR. LA AI TI L-C Occupancy (per Int'l Building Code): g 9 ' re' 1 +r,- Oc'_crzr:ga7" 1-0.4-0 Utility Purveyor: Water: Sewer: Indicate type of plumbing fixtures and/or gas piping outlets being installed and the quantity below: Fiztui?e,Type Qt : Ftxture'Type ;�, Q 'ixtureType"F '.. 2ty'IFtxture'.Typ ' Bathtub or combination bath/shower Drinking fountain or water cooler (per head) Wash fountain 0 Gas piping outlets �` V Bidet 6 Food -waste grinder, commercial C) Receptor, indirect waste v Clothes washer, domestic 0 Floor drain I Sinks 0 Dental unit, cuspidor Q Shower, single head trap 0 Urinals Cs Dishwasher, domestic, with independent drain 0 Lavatory , Water Closet Building sewer or trailer park sewer Rain water system — per drain (inside building) O Water heater and/or vent L 1 Additional medical gas inlets /outlets — six or more 0 Industrial waste pretreatment interceptor, including its trap and vent, except for kitchen type grease interceptors (S Repair or alteration of water piping and/or water treating equipment 0 Repair or alteration of drainage or vent piping Medical gas piping system serving one to five inlets /outlets for specific gas 0 Q:'Applications\Fmms- Applications On Line'3 -2006 - Permit Applicatinn.doc Revised: 9 -2006 bn Page 5 of 6 MECHANICAL PERMIT INFORMATION - 206 -431 -3670 MECHANICAL CONTRACTOR INFORMATION yep Company Name: Mailing Address: Contact Person: E -Mail Address: Contractor Registration Number: City Day Telephone: Fax Number: State Zip Expiration Date: Valuation of Mechanical work (contractor . id price): $ 3 Cf , o Scope of Work (please provide detailed infor , tion): ti •Tt%1L10 j ; ti Err (f i~ I- Ot' O'S r} c-c. /kr k e- 5ecTi0 is!' OF AIJ C.x1S"T,A c -' felt . mAL.i._ . lOO i -r7c s e F IMM v' f_ c K ANh Ret = _ o p tu:-T W-eAK ro co r\ p L. &T f-I VA C- 5 j T i T/-1r.Kr 5P4c - -C, Use: Residential: New .. -- ❑ Replacement .. Commercial: New . - -. ® Replacement .... Fuel Type: Electric Gas .... ❑ Other: Indicate type of mechanical work being installed and the quantity ow. Unit Type: Qty Unit Type: • Unit e: Qty Boiler /Compressor: Qty 0 Furnace <100K BTU Air Handling Unit >10,000 CFM �� Fire Da er i • 0 -3 HP /] 00,000 BTU Furnace >100K BTU C Evaporator Cooler `` Diffuser I.2. 3 -15 HP /500,000 BTU O Floor Furnace U Ventilation Fan Con.. ted to Single Duct 0 Thermostat , HP /1,000,000 BTU 0 Suspended/Wall/Floor Mounted Heater U Ventilation Sys Wood /Gas Stov i J 30 -50 HP /1,750,000 BTU C Appliance Vent Hood and P . ct C) Emergency Generator d 50+ HP /1,750,000 BTU 0 Repair or Addition to Heat/Refrig /Cooling System e, Incine or - Domestic © Other Mechanical Equipment Air Handling Unit <10,000 CFM 0 cinerator — Comm/Ind 1M V av k ( Leer- .1 L rie4j- I Q:'Applications'd:oms- Applications On Line'3 -2006 - Permit Application.doc Revised: 9 -2006 bh Page 4 of 6 PERMIT APPLICATION NOTES — Applicable to all permits in this application Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject to possible revision by the Permit Center to comply with current fee schedules. Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation. Building and Mechanical Permit The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be requested in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition). Plumbing Permit The Building Official may grant one extension of time for an additional period not exceeding 180 days. The extension shall be requested in writing and justifiable cause demonstrated. Section 103.4.3 Uniform Plumbing Code (current edition). I HEREBY CERTIFY THAT 1 HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING OWNER9R AUT ZED AGENT: Signature: ... Print Name: key! J (.4.) Mailing Address: 1 CV Cleff 5 R S 5 gi t. ilvcivac Date: Villob' Day Telephone: IA-243-313 x 256' P1 rrw ytn_6.H 174- 1S-2..i €s City State Zip Date Application Accepted: t �_ 1 °I Date Application Expires: IA Ifs 101 Staff Initials: QA Applications On Line,3 -2006 - Permit Application.doc Revised: 9 -2006 bh Page 6 of 6 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 -431 -3670 Fax: 206 -431 -3665 Web site: http: / /www.ci.tukwila.wa.us RECEIPT Parcel No.: 6364200010 Permit Number: PG08 -209 Address: 837 SOUTHCENTER MALL TUKW Status: APPROVED Suite No: Applied Date: 07/18/2008 Applicant: MARC ECHO CUT & SEW Issue Date: Receipt No.: R08 -03014 Payment Amount: $152.00 Initials: WER Payment Date: 08/21/2008 08:49 AM User ID: 1655 Balance: $0.00 Payee: J E M CONSTRUCTION TRANSACTION LIST: Type Method Descriptio Amount Payment Check 9583 152.00 ACCOUNT ITEM LIST: Description Account Code Current Pmts PLUMBING - NONRES 000.322.103.00.0 152.00 Total: $152.00 471 8/21 P10 1 O .%. doc: Receipt -06 Printed: 08 -21 -2008 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-43 1 -3670 Fax: 206 -431 -3665 Web site: http: //www. ci. tukwila. wa. us SET RECEIPT RECEIPT NO: R08 -02638 Initials: JEM Payment Date: 07/18/2008 User ID: 1165 Total Payment: 1,388.54 Payee: LAMI GRUBB MANAGEMENT SERVICES, INC. SET ID: S000001081 SET NAME: Tmp set/Initialized Activities SET TRANSACTIONS: Set Member Amount D08 -379 1,163.83 EL08 -1015 94.21 M08 -188 101.50 0:82 29.00 TOTAL: 1,388.54 TRANSACTION LIST: Type Method Description Amount Payment Check 0688 1,388.54 TOTAL: 1,388.54 ACCOUNT ITEM LIST: Description Account Code Current Pmts ELECTRICAL PLAN - NONRES PLAN CHECK - NONRES 000.345.832.00.0 94.21 000/345.830 1,294.33 TOTAL: 1,388.54 :-.i-a O7/18 ?716 IO!AL. 1388.51: y NSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 I 1.)e g2elf PType A/ lr'v rte"!' /! 6 C`y t of Inspection: / / •., 91 - /Yetis•A Address f 7 1770/ ` / Date Called: Special Instructions: Date Wanted: Requester: Phone No: 2 53-25$ -/gzp C-0 Approved per applicable codes. El Corrections required prior to approval. /1 COMMENTS: Peorrr►/ i ctrn Spector: Da 0 $• x.00 REINSPECTION E REQU ED. Prior to inspection, fee must be id at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Re eipt No.: Date: INSPECTION NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 INSPECTION RECORD Retain a copy with permit Pro ect: Type nspection: ?(_ Address Date Called: ( Special Instructions: / Date Wanted: � ( .- 24'd ' .air p.m. Requester: Phone No: Approved per applicable codes. Corrections required prior to approval. COMMENTS: Inspector: Pk-/! Date: -Z -d6- ❑ $60.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Receipt No.: 'Date: INSPECTION NO. INSPECTION RECORD /36 0,53, , 7 Retain a copy with permit f�' PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 Project: AAATC— CK0 C_uT *SEw Type of Inspection: d ), t dc, - Address: 1) 5 , ` , `� ( - rM Date Calledf Special Instructions: (90 ;A CZ'tri - B'S g 7s P -t, it ;, \ _r"- k r Date Wanted: ` (� 2 rr ' a�ry p.m. Requester: Phone No: 7 3'- 2 5 - 1 ?7._), 0 Approved per applicable codes. Corrections required prior to approval. COMMENTS: -T! - 1 4-or (? - ; i'`c 7li A ki.S.P.--( i e_1\--79,--1 A -ey-1-- % , iti-P or 4- `i,`, \_ Le A- i - l ." .1e.� i Al 11 -._ . Date: C 2 G - 0 0 $60.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Receipt No.: 'Date: INSPECTION NO. INSPECTION RECORD Retain a copy with permit oSi -71 PERMIT NO. CITY OF TUKWILA BUILDING DIVISION R 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 Project: K uT MA kO SE kJ Type of Inspection: �� l J� 6/0,} Address: Y. s ✓`.' " I f r Date Called: ' Special Instructions: , 1-Ar_ pt„,_,4,4,,,,,ti kr? <AJse 0(7 t y 1' Z Date Wanted: 2 S_ us/ 2.im' Requester: Phones ^ 25- t -2 Approved per applicable codes. Corrections required prior to approval. COMMENTS: La k Ud"i J.Q� Inspect Date: a- -7_5"- v EJ $60.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Receipt No.: Date: ?GoBoc1 ES -009 For Health Hazard Applications Job Name Job Location Engineer Approval 4c kc Cc& / Soul ✓`Le oke- god/ be,, ekke 0e-eA Contr Approval ContractAU1H,.01■'11108 RepresentaRJKYVILA PUak1e w6Rgt4 sr CORRECTION Series 009 Reduced Pressure Zone Assemblies Sizes: 1/4" - 3" (8 - 80mm) Series 009 Reduced Pressure Zone Assemblies are designed to protect potable water supplies in accordance with national plumbing codes and water authority requirements. This series can be used in a variety of installations, including the prevention of health hazard cross connections in piping systems or for con- tainment at the service line entrance. This series features two in -line, independentyche tured springs and replaceable check seats %kit relief valve. Its compact modular design faci nance and assembly access. Sizes 1/4" - 1" have tee handles. Features • Single access cover and modular check dnstru for ease of maintenance • Top entry - all internals immediately acce 'OD I'0 ,fin MPLIAN tiVED AUG 1 8 2008 ction AUG 13 2008 PERMIT CENTER ible City Of Tukwi at Cock • Captured springs for safe maintenance 1 �NG D • Internal relief valve for reduced installation clear n l�V AVA • Replaceable seats for economical repair • Bronze body construction for durability 1/4" - 2" (8 - 50mm) • Fused epoxy coated cast iron body 21/2" and 3" (65 and 80mm) • Ball valve test cocks — screwdriver slotted 1/4" - 2" (8 - 50mm) • Large body passages provides low pressure drop • Compact, space saving design • No special tools required for servicing Specifications A Reduced Pressure Zone Assembly shall be installed at each potential health hazard location to prevent backflow due to backsiphonage and /or backpressure. The assembly shall con- sist of an internal pressure differential relief valve located in a zone between two positive seating check modules with cap- tured springs and silicone seat discs. Seats and seat discs shall be replaceable in both check modules and the relief valve. There shall be no threads or screws in the waterway exposed to line fluids. Service of all internal components shall be through a single access cover secured with stainless steel bolts. The assembly shall also include two resilient seated isolation valves, four resilient seated test cocks and an air gap drain fitting. The assembly shall meet the requirements of: USC Manual 8th Editiont; ASSE Std. 1013; AWWA Std. C511; CSA B64.4. Shall be a Watts Regulator Co. Series 009. tDoes not indicate approval status. Refer to Page 2 for approved sizes & models. Canada: 5435 North Service Rd., Burlington, ONT L7L 5H7;www.wattscanada.ca Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials without prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold. 2" 009M2QTHC First Check Module Assembly Test Cock No. 4 Second Check Module Assembly Relief Valve Assembly Water Outlet Now Available WattsBox Insulated Enclosures. For more information, send for literature ES -WB. IMPORTANT. INQUIRE WITH GOVERNING AUTHORITIES FOR LOCAL INSTALLATION REQUIREMENTS 9001 CERTIFIED WATTS® REGULATOR USA: 815 Chestnut St., No. Andover, MA 01845 -6098; www.wattsreg.com Available Models: 1/4" - 2" (8 - 50mm) St ffix: quarter -turn ball valves S - bronze strainer LF - without shutoff valves AQT - elbow fittings for 360° rotation 3/4" - 2" (20 - 50mm) only PC - internal Polymer Coating LH - locking handle ball valves (open position) SH - stainless steel ball valve handles HC - 21/2" inlet/outlet fire hydrant fitting (2" valve) Prefix: C - U - clean and check strainer 3/4" - 1" (20 - 25mm) only union connections (see ES-U009) Available Models: 21/2" - 3" (65 - 80mm) Suffix: NRS - non - rising stem resilient seated gate valves OSY - UUFM outside stem and yoke resilient seated gate valves S -FDA - FDA epoxy coated strainer QT -FDA - FDA epoxy coated quarter -turn ball valve shutoffs LF - s - without shutoff valves cast iron strainer Note: The installation of a drain line is recommended. When installing a drain line, an air gap is necessary (see ES -AG). Materials: 1/4" - 2" (8 - 50mm) Bronze body construction, silicone rubber disc material in the first and second check plus the relief valve. Replaceable poly- mer check seats for first and second checks. Removable stain- less steel relief valve seat. Stainless steel cover bolts. Standardly furnished with NPT body connections. For optional bronze union inlet and outlet connections, specify prefix U (1/2" - 2 "(15 - 50mm)). Series 0090T furnished with quarter turn, full port, resilient seated, bronze ball valve shutoffs. Air Gaps and Elbows Materials: 21/2" and 3" (65 - 80mm) • (FDA approved) Epoxy coated cast iron unibody with bronze seats • Relief valve with stainless steel seat and trim • Bronze body ball valve test cocks Pressure / Temperature Series 0091/4" - 2" (8 - 50mm) Suitable for supply pressure up to 175psi (12 bar). Water temperature: 33 °F - 180 °F ( -3 °C - 75 °C). Sizes 21/2" and 3" (65 and 80mm) are suitable for supply pressures up to 175psi (12 bar) and water temperature at 110 °F (43 °C) continuous, 140 °F (60 °C) intermittent. Standards USC Manual 8th Editiont ASSE No. 1013 AWWA C511 -92 CSA B64.4 IAPMO File No. 1563. tDoes not indicate approval status. See below for approved models. Approvals ASSE, AWVVA, CSA, IAPMO Approved by the Foundation for Cross - Connection Control and Hydraulic Research at the University of Southern California. Approval models QT, AQT, PC, NRS, OSY. UL Classified 3/4" - 2" (20 - 50mm) (LF models only) 21/2" and 3" (65 and 80mm) with OSY gate valves. MODEL for 909, 009 and 993 sizes DRAIN OUTLET in. mm in. DIMEIISIONS A mm in. B mm WEIGHT lbs. kgs. 909AG -A 1/4" -1/2" 009, 1/2 13 23/s 60 31e 79 .625 .28 3/4° 009M2/M3 909A'Gs C _. 3/4 " -1" 009/909, 1 " -11/2" 009M2 1 25 3'/4 83 4' /e 124 1.50 .68 909AG -F 11/4 " -2" 009M1, 2 51 43/8 111 63/4 171 3.25 1.47 11/4" -3" 009/909, 2" 009M2, 4 "-6" 993 909AG -K 4 "-6" 909, 3 76 63/8 162 95 /e 243 6.25 2.83 8 " -10" 909M1 909AG -M 8 " -10" 909 4 102 73/8 187 1114 394 15.50 7.03 909EL -A 1/4 " -1/2" 009, 3/4" 009M2/M3 - - - - - - - - 909EL-C 3/4 " -1" 009/909, - - 23/8 60 23/8 60 .38 .17 * 909EL -F 11/4 " -2" 009M1, - - 35/8 92 35/8 92 2 .91 11/4 " -2° 009/909, 2" 009M2, 4 "-6" 993 909EL -H 21/ " -3" 009/909 - - - - - - - - Vertical A B Dimensions and Weight: 1/4" - 2" (8 - 50mm) 009 Suffix HC – Fire Hydrant Fittings dimension 'A' = 25" (637mm) 009 1/4" – 2" SIZE (DN) ill mm in. A mm in. B mm in. DIMENSIONS C mm ( APPROX.) 0 in. mm in. I 1 L mm in. !STRAINER DIMENSIONS in. mm WEIGHT Ibs. kg. M mm N in. 1/4 8 10 250 4Ya 117 33/4 86 11/ 32 512 140 23/4 60 21/2 64 5 2 V4 10 10 250 4% 117 33/8 86 11/4 32 512 140 23/4 60 2' 64 5 2 1/2 15 10 250 4% 117 3% 86 11/4 32 512 140 23/4 70 21/4 57 5 2 3/4 20 103/4 273 5 127 312 89 11/2 38 63/4 171 33/16 81 23/4 70 6 3 1 25 163/4 425 51/2 140 3 76 21/2 64 912 241 33/4 95 3 76 12 5 11/4 32 173/8 441 6 150 312 89 21/2 64 113 /8 289 4' /i6 113 3' 89 15 6 1' 40 173/8 454 6 150 3' 89 212 64 11' /a 283 4' /e 124 4 102 16 7 2 50 21% 543 73/4 197 412 114 314 83 131/2 343 515/16 151 5 127 30 13 Dimensions and Weight: 21/2" and 3" (65 and 80mm) 009 STRAINER SIZE in. mm M in. mm DIMENSIONS (approx.) N in. mm Nit in. mm 2'/2 65 10 254 612 165 93/4 248 WEIGHT lbs. kgs. 28 12.7 3 80 10' /a 257 tClearance for servicing 7 178 10 254 34 15.4 Watts G -4000 Series QT – Ball Valves MODEL • ' SIZE DN . in. mm in. • A mm in. C mm . in. DIMENSIONS D mm (APPROX.) E in. mm in. I L mm 1 in. R mm in. U mm WEIGHT lbs. kgs. 009LF 212 65 — — — — 41/2 114 — — 181/8 460 — — 10% 270 76 34.5 0090SY 212 65 331/4 845 15'/8 403 412 114 163/8 416 18'/8 460 73/4 197 105 /8 270 166 75.3 009NRS 21/2 65 3314 845 113/8 289 412 114 16% 416 181/8 460 73/4 197 105 /e 270 161 73.0 0090T 21/2 65 331/4 845 6 152 412 114 163/e 416 181/8 460 73/4 197 105 /e 270 150 68.0 009LF 3 80 — — — — 41 114 — — 181/8 460 — — 10% 270 76 34.5 0090SY 3 80 3414 870 18' 470 412 114 16% 422 181/a 460 83/4 222 10% 270 198 89.8 00914i3S 3 80 341/4 870 123/4 324 41/2 114 165 422 18'/R 460 83/4 222 10% 270 191 86.6 0090T 3 80 341/4 870 7 178 41/2 114 165 422 18'/8 460 83/4 222 10% 270 158 71.7 Capacity Pet-tom-lance as established by an independent testing laboratory. '/" (8mm) 009QT kPa psi 138 20 117 17 96 14 76 1 55 8 35 5 AP D kPa psi 138 20 117 17 96 14 76 11 55 8 35 50 .25 .60 .75 1.17 gpm .95 1.9 2.9 38 4.5 Ipm 3/4" (10mm) 009QT 25 50 .75 1.25 1.50 2.5 3.1 gpm AP 0 .95 1.9 2.9 3 8 4.8 5.7 9.4 11.8 Ipm kPa psi 172 25 138 20 103 15 69 10 %" (15mm) 009QT * 35 5 AP 0 kPa psi 207 30 165 24 124 18 83 12 41 6 0 0 02 AP 07.6 2.5 5 7.5 10 12.5 15 gpm 3 8 9.5 19 28.5 38 47.5 57 Ipm 5 7.5 15 fps 1.5 2.3 4.6 mps 34" (20mm) 009M3QT * f J'I kPa psi 207 30 172 25 138 20 103 15 69 10 35 5 0 0 AP 0 6 10 14 18 22 26 30 34 38 42 46 gpm 23 38 53 68 84 99 114 129 144 160 175 Ipm 7.5 15 fps 2.3 4.6 mps 1" (25mm) 009M2QT ES -009 0403 5 10 20 30 40 50 60 70 80 gpm 19 38 76 114 152 190 228 266 304 Ipm 7.5 15 fps 2.3 4.6 mps `Typical maximum system flow rate (7.5 feet/sec., 2.3 meters/sec.) 11/4" (32mm) 009M2QT kPa psi 172 25 138 20 103 15 69 10 35 5 0 0 AP O kPa psi 207 30 172 25 138 20 103 15 69 10 35 5 0 0 AP 0 10 20 30 40 50 60 70 80 gpm 38 76 114 152 190 228 266 304 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps 11/2" (40mm) 009M2QT kPa psi 207 30 172 25 138 20 103 15 69 10 35 5 0 0 AP 0 10 20 30 40 50 60 70 80 90 100 1 0 120 gpm 38 76 1 4 152 190 228 266 304 342 380 418 456 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps 2" (50mm) 009M2QT * kPa psi 172 25 138 20 103 15 69 10 35 5 0 0 AP 0 20 40 60 80 76 152 228 304 5 7.5 1.5 2.3 100 120 140 160 180 200 gpm 380 456 532 608 684 760 Ipm 10 15 fps 3.0 4.6 mps Ph" (65mm) 009 kPa psi 172 25 138 20 103 15 69 10 35 5 0 0 25 50 75 100 125 150 175 200 225 250 gpm 05 10- 295 380 475 570 665 760 885 950 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps 3" (80mm) 009 * 0 25 50 75 100 125 150 175 200 225 250 275 300 325 gpm AP 0 95 190 285 380 475 570 665 760 855 950 1045 11401235 Ipm 5 7.5 10 fps 1,5 2.3 3.0 mps © Watts Regulator Co., 2002 Printed in U.S.A. • 10g/051/08 �H /AIL 113IEIR EIN(01M ERJN G City rof Tukwila; WA - Departmen "t_ of Community Development 6300 Southcenter Blvd: Suite #4100 ukwila, WA 98.1$8 Res Mare -Eeke• Cut it Sew Space #lc M fSouthcentter Mall 633 Southcen "ter Parkway 'Tukwila, WA '.081:88 Project No: R018-005!004 Application,N PGOS 230 To whom it may concern,, RECEIVED �A r14 'lt_IU8 TIJIC�1v'.'i PUBLIC WORKS 'We offer fhe`faowing.i-e"sponse"sto yourp1umb`inegas review comments 'dated? 7O8: Comment: Provide a,mali key Tim Aso our inspector c na f nd location of Marc ;Ec -a space. - Responsea A dded ikey map to -sheet M2: Comment: ,Please specify size, manufactu erand,model W of proposed RPPA'(Plea "se snake' sure RiPPA is on Wash- ' State Dept. of .Health ilisst of approved ibackflows): !Re"sponse Added rfequesteed o-ftri onto sheet,N12: Commeiit ISubrriit .cutsheetiof 'the ,RPPAand (circle the heyou- jplanto'ii talt: Response` Cut =sh ee [ riV ll lbe isu'bmitted.- Sincerely, iHALLBERG;ENGINEERIN Scott A. Carter et file CO'RRECTION 0,. i Aprojects \ btiG08= ;0196\04 \correspondence Utt20080805:doc ,Mechaical /',E %ctiiea% tor-mating ,Engineers 1750 Commerce eaurt-,, w iite Rea" Lai<e,,rm 155110 • IPISone (651) 7481100 Fax (651) 748 9370 ,; www.'hanbe togineetii bTh rYcl, RECEIVED AUG 13 2008 PERMIT CENTEF June 31, 2008 • • Cizy of Tukwila Jim Haggerton, Mayor Department of Community Development Jack Pace, Director Kevin Wendell 100 East Swissvale Avenue Pittsburg, PA 15218 RE: CORRECTION LETTER #1 Plumbing /Gas Piping Application Number PG08 -209 Marc Ecko Cut and Sew — 837 Southcenter Mall Dear Mr. Wendell, This letter is to inform you of corrections that must be addressed before your plumbing permit can be approved. All correction requests from each department must be addressed at the same time and reflected on your drawings. I have enclosed comments from the Public Works Department. At this time the Building Department has no comment. Public Works Department: Joanna Spencer at 206 - 431 -2440 if you have questions regarding the attached comments. Please address the attached comments in an itemized format with applicable revised plans, specifications, and /or other documentation. The City requires that two (2) complete sets of revised plans, specifications and /or other documentation be resubmitted with the appropriate revision block. In order to better expedite your resubmittal, a `Revision Submittal Sheet' must accompany every resubmittal. I have enclosed one for your convenience. Corrections /revisions must be made in person and will not be accepted through the mail or by a messenger service. If you have any questions, please contact me at (206) 431 -3670. Sincerely, 4,64_ Brenda Holt Permit Coordinator encl xc: File No. PG08 -209 P:\Pennit Center\ Correction Letters \2008\PG08 -209 Correction Ltr #1.DOC wer 6300 Southcenter Boulevard, Suite #100 • Tukwila, Washington 98188 • Phone: 206 - 431 -3670 • Fax: 206 - 431 -3665 PUBLIC WORKS DEPARTMENT COMMENTS DATE: July 29, 2008 PROJECT: Marc Ecko Cut & Saw 837 Southcenter Mall PERMIT NO: PG08 -209 PLAN REVIEWER: Contact Joanna Spencer (206) 431 -2440 if you have any questions regarding the following comments. 1) Please revise your plan per attached mark -up. 2) Applicant or tenant shall submit executed Non - Residential Sewer Use Certification form since no form was submitted with the building tenant improvement permit D08 -375. Form is attached. P: joanna/comments 1 PGO8 -209 • PLANPI d � W %ROUTING SLIP ACTIVITY NUMBER: PG08 -209 DATE: 08 -13 -08 PROJECT NAME: MARC ECKO SITE ADDRESS: 837 SOUTHCENTER MALL Original Plan Submittal X Response to Correction Letter # 1 Response to Incomplete Letter # Revision # After Permit Issued DEPARTMENTS: Buil ing Division Pi Pub is Worlts Fire Prevention Structural Planning Division ❑ Permit Coordinator DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete Comments: Incomplete n DUE DATE: 08 -14 -08 Not Applicable Permit Center Use Only . • INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED: Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: TUES/THURS RO TING: Please Route Structural Review Required ❑ No further Review Required REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: Approved ❑ Approved with Conditions Notation: REVIEWER'S INITIALS: DUE DATE: 09-11 -08 Not Approved (attach comments) ❑ DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: Documents/routing slip.doc 2 -28 -02 410PERMIT COORD COPY 4111 PLAN REVIEW /ROUTING SLIP ACTIVITY NUMBER: PG08 -209 DATE: 07 -18 -08 PROJECT NAME: MARC ECKO CUT & SEW SITE ADDRESS: 837 SOUTHCENTER MALL X Original Plan Submittal Response to Incomplete Letter # Response to Correction Letter # Revision # after Permit Issued DEPARTMENTS: Avn 1-7-5-vv Buikoing Division Fire Prevention n Planning Division Publi W ri al ks ki,_1,6,0,Structural � Permit Coordinator n DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete ► Incomplete Comments: DUE DATE: 07-22-08 Not Applicable ❑ Permit Center Use Only INCOMPLETE LETTER MAILED: Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: LETTER OF COMPLETENESS MAILED: TUES/THURS ROUTI G: Please Route Structural Review Required REVIEWER'S INITIALS: No further Review Required DATE: El APPROVALS OR CORRECTIONS: Approved n Approved with Conditionsn Notation: REVIEWER'S INITIALS: DUE DATE: 08-19-08 Not Approved (attach comments) DATE: Permit Center Use Only CORRECTION LETTER MAILED: 11116 Departments issued corrections: Bldg Fire ❑ Ping ❑ PW [`'� Staff Initials: (j / Documents/routing slip.doc 2 -28-02 • City of Tukwila Steven M. Mullet, Mayor Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 -431 -3665 Web site: http: / /www.ci.tukwila.wa.us Steve Lancaster, Director Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: /l3 /0 Plan ChecWPermit Number: PC-�� a 001 ❑ Response to Incomplete Letter # Response to Correction Letter # i ❑ Revision # after Permit is Issued ❑ Revision requested by a City Building Inspector or Plans Examiner Project Name: j M ' I aZ_C �L k 0 Project Address: QsCP_ tL15O (o? Souk \c V Pr Contact Person: . v,-\ w,1e 11 Phone Number://5 i X5511 o�Q 765 Summary of Revision: ern Vi d.2.c� ,NIAI\ MAP, JACK (oc j d e vt P 7 4 rW144 (oin IlleceNED WV OF nowtif3/4 A0113 att NITER Sheet Number(s): "Cloud" or highlight all areas of revision including date o revisi c\-7-a_f 0c Received at the City of Tukwila Permit Center by: �( Entered in Permits Plus on \applications\forms- applications on linelrevision submittal Created: 8 -13 -2004 Revised: Untitled Page • General /Specialty Contractor A business registered as a construction contractor with Lii1 to perform construction work within the scope of its specialty. A General or Specialty construction Contractor must maintain a surety bond or assignment of account and carry general liability insurance. Business and Licensing Information Name Phone Address Suite /Apt. City State Zip County Business Type Parent Company J E M CONSTRUCTION INC 2538432765 29506 8TH AVE S ROY WA 98580 PIERCE CORPORATION UBI No. Status License No. License Type Effective Date Expiration Date Suspend Date Previous License Next License Associated License Specialty 1 Specialty 2 601770782 ACTIVE JEMCOI.033DD CONSTRUCTION CONTRACTOR 3/4/1997 5/12/2009 GENERAL UNUSED Business Owner Information Name Role Effective Date Expiration Date MILLER, JAMES E 01/01/1980 Bond Information Insurance Information Page 1 of 2 Insurance Bond Bond Effective Expiration Cancel Impaired Bond Received Bond Company Name Account Number Date Date Date Date Amount Date 3 CBIC SA7695 03/01/2002 Until Cancelled $12,000.0003/19 /2002 2 CBIC SA7695 03/01/1998 03/01/2002 $6,000.00 /19/2002 1 CBIC SA7695 03/04/1997 03/01/1998 $6,000.00 Insurance Information Page 1 of 2 Insurance Company Name Policy Number Effective Date Expiration Date Cancel Date Impaired Date Amount Received Date 9 OHIO CAS INS CO BL00353040470 12/02/200312/02 /2008 $1,000,000.0011 /27/2007 8 OHIO CAS INS CO BL00353040470 12/02/200212/02 /2003 $1,000,000.0004 /28/2003 7 OHIO CAS INS CO 52432455 05/12/2001 05/13/2003 $2,000,000.0003 /19/2002 6 OHIO CAS INS CO TBA 05/12/200005/12 /2001 5 TRAVELERS 1680224H9717C0F99 05/12/1999 05/12/2000 https: / /fortress.wa. gov /lni/bbip/Detail. aspx ?License= JEMCOI* 03 3DD 08/21/2008 ABBREVIATIONS AC AFF AMP AP BTU C BV CFH CFM CHW CHWR CHWS CLG CO CR CW DB DEMO DIA DIFF DWG DX EAT ELEC ELEV EMS EWB EWT EXH EXIST F FSD FCO FD FD FDC FFE FLR FPM Fr GA GAL GC GPH HP HVAC HW HZ ID KW LAT AIR CONDITION ( -ING, -ED) ABOVE FINISHED FLOOR AMPERE (AMP, AMPS) ACCESS PANEL BRITISH THERMAL UNIT CIRCUIT BALANCING VALVE CUBIC FEET PER HOUR CUBIC FEET PER MINUTE CIRCULATING HOT WATER CHILLED WATER RETURN CHILLED WATER SUPPLY CEILING CLEANOUT CONDENSATE RETURN COLD WATER DECIBEL DEMOLITION DIAMETER DIFFUSER DRAWING DIRECT EXPANSION ENTERING AIR TEMPERATURE ELECTRICAL ELEVATION ENERGY MANAGEMENT SYSTEM EXTERNAL STATIC PRESSURE ENTERING WET BULB ENTERING WATER TEMPERATURE EXHAUST EXISTING FAHRENHEIT COMBINATION FIRE /SMOKE DAMPER FLOOR CLEANOUT FIRE DAMPER FLOOR DRAIN FIRE DEPARTMENT CONNECTION FINISHED FLOOR ELEVATION FLOOR FEET PER MINUTE FOOT OR FEET GAGE OR GAUGE GALLONS GENERAL CONTRACTOR GALLONS PER HOUR HORSEPOWER HEIGHT HEATING, VENTILATING, AIR CONDITIONING HOT WATER HERTZ INSIDE DIAMETER INVERT KILOWATT LEAVING AIR TEMPERATURE LBS LWB LWT MA MAX MIN MISC NA NC NIC NTS OA OBD ORD PH PVC RA RD REC REL RH RM RPM SA SAN SD SF SP SPEC ST STD TD TSP V P VFD VOLL VTR W/ W/O WC WCO WT POUNDS LEAVING WET BULB LEAVING WATER TEMPERATURE MIXED AIR MAXIMUM THOUSAND BTU'S /HR MINIMUM MISCELLANEOUS NOT APPLICABLE NOISE CRITERIA NOT IN CONTRACT NOT TO SCALE OUTSIDE AIR OPPOSED BLADE DAMPER OVERFLOW ROOF DRAIN PHASE (ELECTRICAL) POLYVINYL CHLORIDE RETURN AIR ROOF DRAIN RECESSED RELIEF RELATIVE HUMIDITY ROOM REVOLUTIONS PER MINUTE SUPPLY AIR SANITARY SMOKE DAMPER SQUARE FEET STATIC PRESSURE SPECIFICATION STORM STANDARD TEMPERATURE DIFFERENCE TOTAL STATIC PRESSURE TYPICAL VOLTS VARIABLE FREQUENCY DRIVE VARIABLE SPEED DRIVE VOLUME VENT THROUGH ROOF WATTS WITH WITHOUT WATER CLOSET WALL CLEANOUT WEIGHT EQUIPMENT TAGS ACCU AHU AHUP BP CDWP CEF CHWP CP CPR CRP DHC ECH EF EHC ES EUH EWC EWH FCU FPB AIR COOLED CONDENSING UNIT AIR HANDLING UNIT AIR HANDLING UNIT PUMP BOOSTER PUMP CONDENSER WATER PUMP CEILING EXHAUST FAN CHILLED WATER PUMP CIRCULATING PUMP CONDENSATE PUMP AND RECEIVER CONDENSATE RETURN PUMP CABINET UNIT HEATER DUCT HEATING COIL ELECTRIC CABINET HEATER EXHAUST FAN ELECTRIC HEATING COIL ELECTRONIC SENSOR ELECTRIC UNIT HEATER ELECTRIC WATER COOLER ELECTRIC WATER HEATER FAN COIL UNIT FAN POWERED VARIABLE AIR VOLUME GWH HU HUH HWP MAU PCWP PHWP PRV REF RF RH RTU SCWP SEP SHWP SP TF USF V BOX VA WS GAS WATER HEATER HUMIDIFIER HORIZONTAL UNIT HEATER HEATING WATER PUMP INTAKE HOOD MAKE -UP AIR UNIT PRIMARY CHILLED WATER PUMP PRIMARY HEATING WATER PUMP POWER ROOF VENTILATOR RELIEF EXHAUST FAN RETURN FAN RELIEF HOOD ROOFTOP UNIT SECONDARY CHILLED WATER PUMP SEWAGE EJECTOR PUMP SECONDARY HEATING WATER PUMP SUMP PUMP TRANSFER FAN UTILITY SET FAN VARIABLE AIR VOLUME BOX VERTICAL UNIT HEATER WATER SOFTENER HVAC SYMBOL LEGEND DUCTWORK SUPPLY DUCT UP SUPPLY DUCT DOWN SUPPLY DUCT UP THROUGH ROOF RETURN /EXHAUST /RELIEF DUCT UP RETURN /EXHAUST /RELIEF DUCT DOWN RETURN/EXHAUST/RELIEF DUCT UP THROUGH ROOF MANUAL VOLUME DAMPER MOTORIZED DAMPER FIRE DAMPER W /ACCESS PANEL FIRE /SMOKE DAMPER W /ACCESS PANEL SMOKE DAMPER W /ACCESS PANEL DUCT RISE (OR DROP) EXISTING DUCTWORK TO REMAIN EXISTING DUCTWORK TO REMAIN EXISTING DUCTWORK TO BE REMOVED EXISTING DUCTWORK TO BE REMOVED SUPPLY AIR TERMINAL RETURN /EXHAUST /TRANSFER AIR TERMINAL VAV BOX HORIZONTAL UNIT HEATER VERTICAL UNIT HEATER ACCESS PANEL THERMOSTAT TEMPERATURE SENSOR SMOKE DETECTOR LONG RADIUS ELBOW SHORT RADIUS ELBOW WITH VANES f 12/12 12/12 PLUMBING SYMBOL LEGEND PLUMBING LINETYPE LEGEND 12/12 4- 12/12 12/12 1// 4- 12/12 4- 12/12 fFD 1 12/12 4- FSD I 12/12 HL SD 1 12/12 4- i UP (OR DN) 12/12 4- 4- L 12/12 irfl#1,14 a. En 0 1 P FLOOR DRAIN FLOOR SINK W /HALF GRATE FLOOR SINK W /FULL GRATE BALL VALVE I 1 GATE VALVE 1`J CHECK VALVE 11I DRAIN VALVE lrl ■ 2 -WAY VALVE SOLENOID VALVE MOTORIZED VALVE EMERGENCY GAS SHUT -OFF VALVE Era THERMOSTATIC /PRESSURE BALANCE MIXING VALVE 0 TRAP PRIMING VALVE PRESSURE RELIEF VALVE I I BUTTERFLY VALVE NCI GLOBE VALVE CIRCUIT BALANCING VALVE K' PLUG VALVE X ANCHOR II PIPE FLANGE PIPE GUIDE Q AIR CHAMBER IF WATER HAMMER ARRESTER WALL HYDRANT/ HOSE BIBB EXPANSION TANK i;i WATER METER mi FLOW METER THERMOMETER PRESSURE GAGE i STRAINER PUMP (1) PLUMBING FIXTURE TAG F# FLOOR RECEPTOR TAG FLOW SWITCH 3 -WAY VALVE QQ- BFP BACKFLOW PREVENTER FP a REDUCER ► FLOW ARROW L) STEAM TRAP (F &T) 1-r THERMOSTAT WELL o EXPANSION JOINT FLEXIBLE CONNECTOR T TEST PLUG 0 STEAM TRAP (THERMOSTATIC) VACUUM RELIEF VALVE AQUASTAT 171 PRESSURE REGULATOR 0 PIPE DOWN 0 PIPE UP 0 TEE DOWN III UNION n PIPE CAP S PIPE BREAK MISC. SYMBOL LEGEND EQUIPMENT TAG St CONNECTION TO EXISTING ! REVISION TRIANGLE <> KEY NOTE O SPRINKLER HEAD (SEMI- RECESSED) O SPRINKLER HEAD (UPRIGHT) ® SPRINKLER HEAD (FULLY RECESSED) G G DOMESTIC COLD WATER DOMESTIC COLD WATER (BELOW FLOOR /GRADE) DOMESTIC COLD WATER (EXISTING) DOMESTIC HOT WATER DOMESTIC HOT WATER (EXISTING) GAS GAS (ON ROOF) GAS (EXISTING) GAS (EXISTING ON ROOF) SANITARY SEWER (ABOVE FLOOR /GRADE) SANITARY SEWER (BELOW FLOOR /GRADE) SANITARY SEWER (EXISTING) VENT VENT (UNDERFLOOR /GRADE) VENT (EXISTING) SHEET INDEX MO Ml M2 M3 MECHANICAL TITLE SHEET HVAC PLAN PLUMBING PLAN MECHANICAL SPECIFICATIONS SEPARATE PERMIT REQUIRED FOR Mechanical c Electrical 0 /Plumbing 0 Gas Piping City of Tukwila BUILDING DIVISION - REVISIONS changes shall be made to the scope of work without prior approval of Tukwila Building Division. NOTE: Revisions will require a new plan submittal and may include additional plan review fees KLVIL:.1 VLI) li- R. CODE COMPLIANCE APPRO °.D City. Of It kwlia BUILDING V.ISIONI,.... FILE COPY Permit No. Plan review approval Is subject to errors and omissions. Approval of constmetkm dcwmen does not authorize the violation of any adopted code or ordinance. Receipt of approved Field Copy end corwitions Is - ced: City of Tukwila BUILDING DIVISION CORRECTION LTIR#4..._,. 1608- zoct DATE: JOB NO: DRAWN: 07/08/08 08- 0196.004 MDB CHECKED: SAC /TLG Project Coordination By: 10 U W r:4 ECEIVIEIP . AUG 13 2008 PERMIT GENIE' 711 N. FIELDER RD. ARLINGTON, TX 76012 PH: (817) 635 -5696 FAX: (817) 635 -5699 J ce pip a CO Liu) os NT cl CI Lll zz , � Quu N�� 00 P M 'qO ttY 7/r .1, - QC s HALL g. ENGINEER I t °i a 1 w 0 Mechanical /Electrical Consulting Engineers 1750 Commerce Court, White Bear Lake, MN 55110 (651) 748 -1100 • Fax (651) 748 -9370 REVISIONS 1. LANDLORD REVISIONS - 07/10/08 2. PLUMBING DIVISION REVISIONS - 08/05/08 MECHANICAL TITLE SHEET SHEET NUMBER 0 GENERA L NOTES A. THE MECHANICAL CONTRACTOR IS REQUIRED TO PROVIDE AS PART OF BASE BID A SERVICE CONTRACT INCLUDING ALL FILTER CHANGES AND CLEANING AND MAINTENANCE FOR A PERIOD OF 1 YEAR FROM TURNOVER OF SPACE. B. COORDINATE LOCATIONS OF DIFFUSER GRILLES W /ARCH REFLECTED CEILING PLAN. C. SUBMIT COPIES OF TEST & BALANCE REPORT TO LANDLORD, OWNER & ENGINEER. D. ADJUST DISCHARGE PATTERN OF THE DIFFUSER FOR A VERTICAL FLOW. E. REMOVE ALL EXISTING FIRE SPRINKLER HEADS AND DROP LEGS. PROVIDE NEW HEADS OF TYPE SHOWN. REWORK BRANCHES AND MAINS AS REQUIRED FOR NEW ELEVATION. HEADS TO BE UPRIGHT, SEMI - RECESSED OR FULLY RECESSED FULLY RECESSED TO BE PROVIDED WITH WHITE COVERS. FIRE PROTECTION WORK TO BE PROVIDED BY LANDLORD APPROVED CONTRACTOR. • F. CONTRACTOR SHALL COMPLETELY REMOVE FROM THE PREMISES ALL EQUIPMENT, PIPING, DUCTWORK, CONTROLS, CONTROL WIRING, ETC. AND ALL ASSOCIATED SUPPORTS, BRACING, PADS, ETC. NOT BEING REUSED OR SHOWN ON TO REMAIN WHETHER IN THE DEMISED SPACE, ON THE ROOF OR OTHERWISE LOCATED OUTSIDE OF THE DEMISED SPACE. DO NOT ABANDON IN PLACE. H. DIFFUSER RUNOUT EQUAL TO DIFFUSER CONNECTION UNLESS OTHERWISE SPECIFIED. G. REMOVE ALL UNUSED PIPING, DUCTWORK, AND ACCESSORIES. DO NOT ABANDON. I. ALL EXPOSED ROUND DUCT SHALL BE SPIRAL AND PAINTABLE. J. VERIFY ANY ADDITIONAL HVAC CRITERIA WITH LANDLORD. REQUIREMENTS MAY INCLUDE BUT ARE NOT LIMITED TO: GENERAL HVAC REQUIREMENTS, INSULATION, DUCT AND DUCT FITTINGS, HVAC CONTROLS, HANGERS, AND INSTALLATION. K. SPRINKLER HEAD LOCATIONS ARE FOR REFERENCE ONLY. THE FINAL LOCATIONS NEED TO BE INSTALLED PER CODE AND ARE THE RESPONSIBILITY OF THE CONTRACTOR WHO INSTALLS. A L. ALL SUPPORTS SHALL BE FROM STRUCTURAL BEAMS AND JOISTS, NOT FROM THE FLOOR SLAB OR ROOF DECK ABOVE. M. MAINTAIN A MINIMUM OF 6" UNOBSTRUCTED CLEARANCE HEIGHT IN RETURN AIR PLENUM ABOVE CEILING ALLOWING FOR AIR FLOW BACK TO LANDLORD RTU. KEY NOTES NEW PARALLEL FAN POWERED VAV BOX PROVIDED BY TENANT CONTRACTOR. K PROVIDE NEW 7 -DAY PROGRAMMABLE THERMOSTAT FOR RTU -1 CONTROL MOUNTED 4' -O" A.F.F. COVERED WITH CLEAR LOCAKABLE BOX. REFER TO SPEC 15906 FOR SEQUENCE OF OPERATION. • INSTALL SMOKE DETECTOR FURNISHED BY ELECTRICAL CONTRACTOR IN RETURN OF VAV BOX. DETECTOR SHALL SHUT DOWN HVAC UNIT UPON DETECTION OF SMOKE. • EXISTING DUCTWORK TO REMAIN. PROVIDE FIRE DAMPER. REFER TO DETAIL 4/M1. EXHAUST FAN PROVIDED BY TENANT CONTRACTOR. MECHANICAL CONTRACTOR TO CONNECT 6"0 DUCT TO EXISTING (6 "0 MIN) LANDLORD PROVIDED EXHAUST DUCT. FIELD VERIFY EXISTING EXHAUST DUCT LOCATION. REFER TO ELECTRICAL DRAWINGS FOR EXHAUST FAN SPECIFICATION. HVAC PLAN 1/4" = 1' -0" SPIN -ON BELLNOSE FITTING RIGID ROUND DUCT MAIN DUCT BRANCH MANUAL VOLUME DAMPER wkittnift BRANCH DUCT 4" RIGID DUCT EXTENSION ATTACHED TO DIFFUSER NECK 11' -6" A.F.F. DIFFUSER TYP. DIFFUSER /DUCT CONNECTIONS NO SCALE VAV INLET CONE AND SENSOR FILTERED FAN INLET DUCT FULL SIZE RIGID INLET DUCT. 18" MIN. OR 3 TIMES INLET CONE DIAMETER WHICHEVER IS GREATER VAV BOX COIL ACCESS PANEL IN BOTTOM OF VAV BOX (MINIMUM 6 "x6 ") lot*DISCHARGE DUCT. 4$1A1RFLOW HEATING COIL DUCT ACCESS PANEL (MINIMUM 6 "x6 ") NOTES: DO NOT BLOCK EQUIPMENT ACCESS DOORS AND PANELS DISCHARGE TRANSITION AS REQUIRED TO MATCH VAV OUTLET TO DISCHARGE DUCT. (MAX 22-1/2 DEG.ANGLE) QPARALLEL FAN POWERED VAV BOX NO SCALE SLEEVE 16 GAUGE FOR ALL DUCTS UNDER 24" HEIGHT AND 36" WIDTH, ALL LARGER DUCTS USE 14 GAUGE. 1/8" MAXIMUM VOID BETWEEN SLEEVE AND STRUCTURE PROVIDE SHEET METAL EXTENSION OF EQUAL OR GREATER GAUGE AS DUCT -_ FIRE DAMPER CENTERED IN SLEEVE RETAINING MINIMUM ANGLE 1 -1/2 "x 1 -1/2 "x1/8 ", 14 GAUGE. ANGLE 1" MINIMUM AND COVER CORNERS OF OPENINGS. SECURE ANGLE TO SLEEVE ONLY ON 8" CENTERS WITH #10 STEEL SCREWS. SECURE FIRE DAMPER TO SLEEVE ON 8" CENTERS WITH #10 STEEL SCREWS. SCREWS MUST NOT INTERFERE WITH DAMPER OPERATION. FLAT DRIVE (TYPICAL SIDES) S -SLIP (TYPICAL TOP AND BOTTOM) SLEEVE MUST EXTEND 6" MINIMUM PAST BOTH SIDES OF STRUCTURE (4.- FIRE DAMPER DETAIL NO SCALE PROVIDE ACCESS DOOR WITH "FIRE DAMPER" LABEL. LOCATE ON SIDE OR BOTTOM OF DUCT. DOOR SIZE MUST PERMIT ACCESS AND RESETTING TO EACH DAMPER SECTION. System Checksums By Hallberg Engineering Inc. VAV Parallel Fan -Powered VAV Pic tt Name. Dataset Name:. 1:1.Paukttd.tail GruaMR00-0195. 01C4Li .1{pd,Tranetaft- 13196_004.Jkc TRACEt 700 v6.0 calculated 1101.70 NA on 071`1112Da0 Adonalw - t a sfem Oliecaanaaa. Report Pace 1 0l 1 D LOAD CALCULATIONS NO SCALE <7 MOUNT TRANSFER DUCT AS HIGH AS POSSIBLE, PROVIDE GRILLE ON SALES FLOOR SIDE OF WALL. GRILLE AND DIFFUSER SCHED. COOLING COIL PEAK Iv CLG SPACE PEAK HEATING COIL PEAK TEMPERATURES Pealed al Tlme: MnJHr_ 7114 SUPPLY fdu"Hr: 7115 RETURN 1JI¢1Hr Healing Design DESCRIPTION Looking Haaltq Outside Mr 0A43071110 75.6 E4 .f 67 TITUS 41100: 00 TITUS GAM 26 TMRA 1A1013 55,5 70.0 REMARKS PAINTABLE ADJUSTABLE STD. WHITE FINISH STD. WHITE FINISH PAINTABLE 0 INLET DUCT SIZE Mecum 74.11 70.a NC 0 0.5" SP *papa Pimum Hat Paroanl FAN HP ipare Pulvaut !pate Pena Coll Peak Paaeal Redid 7S.3 MD 10 ism.. Let tuns. * Lak 1DEM 0XTda1 55/70 Samna' O1 Total CONTROL STEPS awe Bona Td lam Of Total R1070R. 75.6 26.D BhVh MIA EFfuft (41 Math Mt DIV. 16 Stank 19401 (%) F. M411TD 0.0 0.13 EfVaWpe Ladle Elwafapa Leeds Fe ONTO 0.4 DIP DA Ylte Mir 0 D 0 0 0 0 DL71te aoIar D D 0.40 Far -rMl DD DA Beydan Land 0 D 0 0 9 0 81711e Cant 0 a 000 Root COr J 0 D D a G a- Rauf Coati D D 900 alati Brim D D D a 9 a c044 a1ltr D 0 0.0] _. 01016 Cand a D 0 D 9 0 arms Land 0 0 0.00 Wall Cara 0 0 0 0 0 a Wait Coact 0 a 0,011 AIRFLOWS Fratklan a D a a a Parham 0 0 aD0 Eapc%e Flaw- afllttaDun a 0 0 a a D Erroscd Flaw - 0 0 0.00 y Maeda 551 Hratq 0 0 0 a 0 InfarRlan 0 0 0 -00 Niel 0 0 Sub Total --. a a 0 a a 0 &uD TM( - a 0 a-OD Supply 2,a43 D 1,11n51IFVI01 0 D htbaraal Wadi Ustds 11..,604 2.901 14.505 25 11,604 211 Infiniti Laedr Llalds a a a.0a Rah., Exhaust 2;043 GS D D People 15„289 16,299 29 9;145 20 Pccpk 0 a 0.00 Rm Esh 4 a Wit 21,559 0 21,559 3a 21.;559 52 Mew 0 0 0.0a Ausaay a a Sub row - -s 49.,452 2;431 54153 92 41,309 140. &u4 rola! -- a 0 0-40 Calling Leal Venalrfhr. Laid Oehtamld. 4v Mind a 0 a a a S,r102 D a t0 a o a D 0 C.nrlq toed VanGlabon Lard Helm/ a a a a 0.411 a a.11a ENGINEERING CKS Cooling Htu11a antlndr lD Dirt a 0 a 0 0 Pahamat Heal 0 a.40 % OA a Eshauat Haat -424 924 -2 OA Freitag' Ddf. - 21,176 10400 oa.it 0.03 DC tope Fad foal a a RA Preheat Dirt 0 0.00 ahR4a0 431.46 Rat. Fan Heal Duet Hata Pkup Reheat at 044Ign 0 a D 0 a a - a a A0d1119nM /formal 0 GM Nylon Bk,s*ryP No. People 519.44 23, f4 33 -9.61 et wid Trodda.u. 49.452 1,977 55,831 1110.00 41,3:93 100.110 ra1d'Tataiaxi* a - 21,176 100.1Z1 COOLING COIL SELECTION AREAS HEATING COIL SELECTION la(al COP WAY lataa Cl p Caal Airflow Enlar DB1tIBA;f Lana 013A784414 Shwa TetM Dfl1a. capsedy Boll AIM= E1d t.d0 tun ME DI MBn tin 'F 'F pmt 'F 'F pnlb ft= ISi3 AfBfs chi 'F 'F Main Cla 4.7 .564 47.2 2.0434 T6,6 623 54.9 55:5 53.3 50.0 Flay 2,460 Attila tit 4.a D.0 MD 79.0 Amt C10 a.0 0.0 D.0 a 0 0 a a a a Pat 0 Aux Hip UM D 0 :0 Dot Plait 9.0 DM D.0 a a-D MD D:D ea D.a 0.0 FrFar Roof a a a 0 Praiaak -212 Reheat as 6551 0 2E 56 D.D 0:0 Thief 4.7 563 wad 0 0 0 Ifaankat DD Odd Vanl G4 D 0 MD OA aD 4.0 Tow -212 Pic tt Name. Dataset Name:. 1:1.Paukttd.tail GruaMR00-0195. 01C4Li .1{pd,Tranetaft- 13196_004.Jkc TRACEt 700 v6.0 calculated 1101.70 NA on 071`1112Da0 Adonalw - t a sfem Oliecaanaaa. Report Pace 1 0l 1 D LOAD CALCULATIONS NO SCALE <7 MOUNT TRANSFER DUCT AS HIGH AS POSSIBLE, PROVIDE GRILLE ON SALES FLOOR SIDE OF WALL. GRILLE AND DIFFUSER SCHED. AI Iv TYPE A B C D ITEM SUPPLY SUPPLY RETURN RETURN DESCRIPTION DUCT MOUNT LAY -IN LAY -IN SURFACE MOUNT MANUFACTURER TITUS TITUS TITUS TITUS MODEL NUMBER TMRA TMSA 350ZRL 350ZRL REMARKS PAINTABLE ADJUSTABLE STD. WHITE FINISH STD. WHITE FINISH PAINTABLE VAV BOX SCHEDULE AN ma AN UNIT TAG VAV -1 AREA SERVED SALES FLOOR MANUFACTURER TITUS MODEL NUMBER DTQP CFM 2150 MINIMUM CFM 0 INLET DUCT SIZE 14 "0 NC 0 0.5" SP 28 FAN HP 3/4 ELECTRIC HEATING COIL (EHC) KW 10 EAT /LAT 55/70 CONTROL STEPS - ELECTRICAL V -PH -CY 208 -3 -60 DISCONNECT DIV. 16 REMARKS 1,2 NOTES: 1. PROVIDE CONTROLS AS REQUIRED TO INTERFACE WITH LANDLORD BUILDING AUTOMATION SYSTEM. 2. BALANCE TO 650 CFM OUTSIDE AIR. VI:VIEWED VC* CODE COMPLIAMC .oV.r) 1 t 1 Ot $9f r1��14 r' +`'lit 1? /.lJt3 ?6o820'i DATE: JOB NO: DRAWN: 07/08/08 08- 0196.004 MDB CHECKED: SAC /TLG 711 N. FIELDER RD. ARLINGTON, TX 76012 PH: (817) 635 -5696 FAX: (817) 635-5699 10 LL4 e U U 00 00 N-- CO E L1.IZ U esF-EE 0 0 IP rn 1 ECEIVED AUG 1 3 X000 PERMIT CENTER HALL ENGINE IN Mechanical /Electrical Consulting Engineers 1750 Commerce Court, White Bear Lake, MN 55110 (651) 748 -1100 • Fax (651) 748 -9370 REVISIONS 1. LANDLORD REVISIONS - 07/10/08 2. PLUMBING DIVISION REVISIONS - 08/05/08 HVAC PLAN SHEET NUMBER Mi • EXTEND NEW 2" VENT TO EXISTING (2" MIN) LANDLORD PROVIDED VENT PIPING. FIELD VERIFY EXACT LOCATION OF EXISTING VENT PIPING PRIOR TO ROUGH -IN. • PROVIDE JOSAM 88250 OR EQUAL TRAP PRIMER WITH ACCESSIBLE SHUT -OFF VALVE. • PIPE DRIP PAN FULL SIZE TO AIR GAP OVER Q PIPE 3/4" FROM ASME RATED T &P VALVE TO AIR GAP OVER L.OR DR , IN KEY NOTES EXTEND AND CONNECT NEW 4" SANITARY SEWER TO EXISTING 4" (MIN) LANDLORD PROVIDED SANITARY SEWER PIPING. FIELD VERIFY EXACT LOCATION, SIZE, FLOW DIRECTION, AND INVERT ELEVATION OF CONNECTION POINT PRIOR TO ROUGH -IN OF NEW SANITARY SEWER. PROVIDE FCO AT POINT OF CONNECTION TO EXISTING. EXTEND AND CONNECT NEW 3/4" CW PIPING TO EXISTING 3 4" (MIN) LANDLORD PROVIDED CW PIPING. FIELD VERIFY EXACT LOCATION OF CW PIPING PRIOR TO ROUGH -IN. PROVIDE SHUTOFF VALVE AT POINT OF CONNECTION TO EXISTING. D • PROVIDE 3/4" WATTS 009 QT REDUCED PRESSURE BACKFLOW PREVENTER ON THE WATER SERVICE WITHIN THE SPACE PRIOR TO MAKING ANY OTHER CONNECTIONS. PROVIDE WATTS 909AG AIR GAP FITTING AND ROUTE WATER OUTLET DOWN IN WALL AND TERMINATE WITH CODE APPROVED AIR GAP OVER FLOOR DRAIN. BACKFLOW PREVENTER SHALL BE ON THE WASHINGTON STATE DEPT. OF HEALTH LIST OF APPROVED BACKFLOW PREVENTERS. UNDERFLOOR PLUMBING PLAN 1/4" = 1' -0" 1 -1/2" 1 -1 /2" **WASTE AND VENT RISER N.T.S. PLUMBING PLAN 2 / 1/4' = WATER RISER N.T.S. MARC ECKO CUT & SEW MALL KEY PLAN 5 N.T.S. vI C M'Li E APPROVED D GENERAL NOTES A. A B. VERIFY ALL CONDITIONS IN THE FIELD. COORDINATE WORK WITH LANDLORD PRIOR TO AND SLAB DEMOLITION. COORDINATE WITH LANDLORD TO PROVIDE OPPORTUNITY FOR SPECIAL INSPECTION AND PHOTOGRAPHIC DOCUMENTATION BY LANDLORD OF BELOW GRADE WORK PRIOR TO THE COVERING UP OF SUCH WORK. TENANT CONTRACTOR SHALL BE RESPONSIBLE FOR RECONSTRUCTION AND PATCHING OF THE SLAB-ON-GRADE SYSTEM, INCLUDING GRAVEL LAYERS, VAPOR BARRIER, AND CONCRETE. C. ALL SUPPORTS SHALL BE FROM STRUCTURAL BEAMS AND JOISTS, NOT FROM FLOOR OR ROOF DECK ABOVE. l'a`w :3 ; 8 'NOB Of Tukwila I CYO I ' E BATHROOM COMPONENT �M� a� Item Model Exist. To Remain New (Add /Replace) Notes: Toilet See Plumbing Fixture Schedule - 1 -- Toilet Seat See Plumbing Fixture Schedule - 1 -- Sink See Plumbing Fixture Schedule - 1 -- Lever Handle Faucet See Plumbing Fixture Schedule 9 - 1 " 2" Pipe Wrap See Plumbing Fixture Schedule - 1 - Water Heater See Water Heater Schedule - 1 -- Service Sink See Plumbing Fixture Schedule - - -- Water Cooler - - - -- Floor Drain See Plumbing Fixture Schedule - 1 -- PLUMBING FIXTURE SCHEDULE ELECTRIC WATER HEATER SCHEDULE EWH FIXTURE NO. UNIT NO. MANUFACTURER MODEL KW CAPACITY (GAL.) STAGES VOLTAGE OUTPUT (GPH © 90' RISE REMARKS EWH -1 A.O. SMITH DEL -6 1.5 6 1 120 1 60 7 NONE PLUMBING FIXTURE SCHEDULE • P# FIXTURE NO. FIXTURE TYPE MANUFACTURER TYPE & MODEL NO, TRIM NO. SUPPORT PIPE SIZES REMARKS TRAP WASTE VENT CW HW P1 WATER CLOSET PRESSURE ASSIST AMERICAN STANDARD CADET (WHITE) 2377.100 CHICAGO FAUCET 1016 FLOOR MOUNT _ 4" " 2" /2 - WHITE SEAT- CHURCH MODEL 295C 16-1/2" RIM HEIGHT P2 LAVATORY AMERICAN STANDARD LUCERNE (WHITE) 0355.012 CHICAGO FAUCET 894 -317 WALL HUNG 1-1/2" 2" 1-'1/2" 1 /2" 1 /2" PROVIDE INSULATED CAST BRASS P -TRAP, HANDICAP INSULATION KIT, (2) CHICAGO FAUCET 1016 ANGLE VALVES, WALL CARRIER, 0.5 GPM FLOW LIMIT Fl FLOOR DRAIN JOSAM 30000 -6A - - 3" 3 " 1-1/2" - - PROVIDE 1 /2" TRAP PRIMER CONNECTION WHERE INDICATED ON PLANS DATE: JOB NO: DRAWN: 07/08/08 08- 0196.004 MDB CHECKED: SAC/TLG 711 N. FIELDER RD. ARLINGTON, TX 76012 PH: (817) 635 -5696 FAX: (817) 635 -5699 Project Coordination By: IQ U ot,3 Mechanical /Electrical Consulting Engineers 1750 Commerce Court, White Bear Lake, MN 55110 (651) 748 -1100 • Fax (651) 748-9370 REVISIONS 1. LANDLORD REVISIONS - 07/10/08 2. PLUMBING DIVISION REVISIONS - 08/05/08 RECENVFr, AUG 13 ZO[► PERMIT CENI-11:; .209 PLUMBING PLAN SHEET NUMBER M2 15010 GENERAL PROVISIONS A. FURNISHING LABOR, MATERIALS, EQUIPMENT AND SERVICES REQUIRED AS SHOWN ON THE DRAWINGS AND SPECIFIED IN DIVISION 15. B. ALL WORK SHALL BE COMPLETE AND SHALL BE LEFT IN OPERATING CONDITION. C. INCLUDE ALL PARTS AND LABOR WHICH ARE INCIDENTAL AND NECESSARY FOR A COMPLETE AND OPERABLE INSTALLATION EVEN THOUGH NOT SPECIFICALLY MENTIONED IN THE CONTRACT DOCUMENTS. ARRANGE WITH APPROPRIATE UTILITY COMPANIES TO PROVIDE TEMPORARY AND PERMANENT UTILITY SERVICES AS REQUIRED AND COORDINATE THEIR INSTALLATION WITH CONSTRUCTION PROGRESS OF THIS PROJECT. PAY ALL FEES AND COSTS CHARGED BY UTILITY COMPANIES FOR UTILITY SERVICES. E. OBTAIN ALL TEMPORARY AND PERMANENT PERMITS AND LICENSES REQUIRED IN CONNECTION WITH THIS DIVISION'S WORK. PAY ALL FEES AND EXPENSES REQUIRED FOR SUCH PERMITS AND LICENSES. F. REQUEST INSPECTIONS AS REQUIRED BY REGULATING AGENCIES AND /OR REGULATIONS. PAY ALL CHARGES FOR INSPECTIONS BY REGULATING AGENCIES OF INSTALLATIONS OF PLANS SPECIFICATIONS. G. PROVIDE THE OWNER WITH A CERTIFICATE OF FINAL INSPECTION AND APPROVAL BY ENFORCEMENT AUTHORITIES. H. MEET OR EXCEED ALL CURRENT APPLICABLE CODES, ORDINANCES AND REGULATIONS FOR ALL INSTALLATIONS. PROMPTLY NOTIFY THE ENGINEER, IN WRITING, IF THE CONTRACT DOCUMENTS APPEAR TO CONFLICT WITH GOVERNING CODES AND REGULATIONS. CONTRACTOR ASSUMES ALL RESPONSIBILITY AND COSTS FOR CORRECTING NON - COMPLYING WORK INSTALLED WITHOUT NOTIFYING THE ENGINEER. I. HIGHER QUALITY OF WORKMANSHIP AND MATERIALS INDICATED IN THE CONTRACT DOCUMENTS TAKES PRECEDENCE OVER THAT ALLOWED IN REFERENCED CODES AND STANDARDS. FURNISH: TO OBTAIN, COORDINATE, SUBMIT THE NECESSARY DRAWINGS, DELIVER TO THE JOB SITE IN NEW CONDITION READY FOR INSTALLATION, UNLOAD AND UNPACK, AND GUARANTEE. J. INSTALL: TO RECEIVE AT THE JOB SITE, STORE, ASSEMBLE, ERECT, SET IN PLACE, ANCHOR, APPLY, FINISH, PROTECT, CLEAN, TEST, START -UP, AND MAKE READY FOR OWNER'S USE. K. PROVIDE: TO FURNISH AND INSTALL. L. CONTRACTOR IS RESPONSIBLE FOR DIMENSIONAL DIFFERENCES, WEIGHTS, ELECTRICAL REQUIREMENTS AND ANY OTHER RESULTING CHANGES, WHEN USING EQUIPMENT OTHER THAN THAT SCHEDULED ON THE DRAWINGS. CONTRACTOR IS RESPONSIBLE FOR ANY ADDITIONAL COSTS INCURRED AS A RESULT OF SUBSTITUTIONS. M. BEFORE SUBMITTING A PROPOSAL ON THE WORK CONTEMPLATED, EXAMINE THE SITE OF THE PROPOSED WORK AND BECOME THOROUGHLY FAMILIAR WITH EXISTING CONDITIONS AND LIMITATIONS. NO EXTRA COMPENSATION WILL BE ALLOWED BECAUSE OF MISUNDERSTANDING AS TO THE AMOUNT OF WORK INVOLVED NOR BIDDERS LACK OF KNOWLEDGE OF EXISTING CONDITIONS WHICH COULD HAVE BEEN DISCOVERED OR REASONABLY ANTICIPATED PRIOR TO BIDDING. N. MECHANICAL EQUIPMENT AND SYSTEMS SHOWN ON THE DRAWINGS AS EXISTING, HAVE BEEN BASED ON EXISTING PLANS, AND MAY NOT BE INSTALLED AS ORIGINALLY SHOWN. IT IS THE CONTRACTORS RESPONSIBILITY TO VISIT THE SITE AND MAKE EXACT DETERMINATION OF THE EXISTENCE, LOCATION AND CONDITION OF SUCH FACILITIES PRIOR TO SUBMITTING A BID. 0. CONSULT THE DRAWINGS AND SPECIFICATIONS OF DIVISION 16 AND OTHER TRADES FOR CORRELATING INFORMATION AND LAY OUT WORK SO THAT IT WILL COORDINATE WITH OTHER TRADES. VERIFY DIMENSIONS AND CONDITIONS (I.E., FINISHED CEILING HEIGHTS, FOOTING AND FOUNDATION ELEVATIONS, BEAM DEPTHS, ETC.) WITH THE ARCHITECTURAL AND STRUCTURAL DRAWINGS. P. DRAWINGS MAY NOT SHOW EVERY RISE AND OFFSET REQUIRED FOR THE WORK. INSTALL PIPING AND DUCTWORK TO ACCOMMODATE THE BUILDING STRUCTURE AND THE WORK OF OTHER TRADES, WITH ALL REQUIRED OFFSETS AND WITHOUT EXTRA COST TO THE OWNER. Q. OBTAIN EXACT LOCATION OF CONNECTION TO EQUIPMENT, FURNISHED BY OTHERS, FROM THE PERSON FURNISHING THE EQUIPMENT. R. GUARANTEE AND MAINTAIN THE STABILITY OF WORK AND MATERIALS AND KEEP SAME IN PERFECT REPAIR AND CONDITION FOR THE PERIOD OF ONE (1) YEAR AFTER THE FINAL COMPLETION OF THE WORK AS EVIDENCED BY ISSUANCE OF THE FINAL CERTIFICATE BY THE ARCHITECT. S. DEFECTS OF ANY KIND DUE TO FAULTY WORK OR MATERIALS APPEARING DURING THE ABOVE MENTIONED PERIOD MUST BE IMMEDIATELY MADE GOOD BY THE CONTRACTOR AT HIS OWN EXPENSE TO THE ENTIRE SATISFACTION OF THE OWNER AND ARCHITECT AND ENGINEER. INCLUDE DAMAGE TO THE FINISH OR THE BUILDING RESULTING FROM THE ORIGINAL DEFECT OR REPAIRS. T. MAGNETIC STARTERS, DISCONNECTS, AND POWER WIRING PROVIDED BY THE ELECTRICAL CONTRACTOR, UNLESS OTHERWISE SPECIFIED. U. CONTROL AND INTERLOCK WIRING PROVIDED BY THE MECHANICAL CONTRACTOR, UNLESS OTHERWISE SPECIFIED. V. PROVIDE ONLY PRODUCTS FROM MANUFACTURER'S WITH LOCAL REPRESENTATION THAT CAN PROVIDE COMPLETE COVERAGE, PARTS AND LABOR, FOR REPLACEMENT AND SERVICE OF THEIR PRODUCTS. PROVIDE ONLY EQUIPMENT THAT WILL FIT IN THE SPACE AVAILABLE AND BE COMPLETELY SERVICEABLE. BRING ANY CONFLICTS TO THE ENGINEER'S ATTENTION PRIOR TO ORDERING THE EQUIPMENT. W. COORDINATE /SCHEDULE ALL WORK WITH THE OWNER TO MINIMIZE ANY DISRUPTIONS. CONFINE ALL INTERRUPTIONS TO THE SMALLEST POSSIBLE AREA. PROVIDE TEMPORARY CONNECTIONS IF REQUIRED TO PROVIDE CONTINUITY OF SERVICE. X. INSPECT ALL AREAS AFFECTED BY THE INTERRUPTIONS AND RETURN ALL AUTOMATICALLY CONTROLLED EQUIPMENT, ELECTRICALLY OPERATED EQUIPMENT TO THE SAME OPERATING CONDITION PRIOR TO THE INTERRUPTION. Y. NO FIRE SPRINKLER OR FIRE ALARM SYSTEMS ARE TO REMAIN INACTIVE AT THE END OF THE WORK DAY. ASSURE THAT THE FIRE SPRINKLER OR FIRE ALARM SYSTEM IS OPERATIONAL AT THE END OF EACH WORK DAY. COORDINATE WITH THE OWNER. Z. PROVIDE NEW MATERIAL AND EQUIPMENT, UNLESS NOTED OTHERWISE. PROTECT EQUIPMENT AND MATERIAL FROM DAMAGE, DIRT AND THE WEATHER. M. PROVIDE THE HIGHEST QUALITY WORKMANSHIP AND PERFORM ALL WORK ONLY BY SKILLED MECHANICS. INSTALL MATERIAL AND EQUIPMENT IN ACCORDANCE WITH MANUFACTURERS' RECOMMENDATIONS, INSTRUCTIONS AND CURRENT STANDARDS. BB. THE ENGINEER RESERVES THE RIGHT TO REJECT MATERIAL OR WORKMANSHIP NOT IN ACCORDANCE WITH THE CONTRACT DOCUMENTS, BEFORE OR AFTER INSTALLATION. CC. ALL PIPING AND DUCTWORK SHALL BE RUN IN THE MOST DIRECT AND STRAIGHT MANNER POSSIBLE MAINTAINING PROPER GRADING. DD. IT IS THE INTENT OF THESE PLANS AND SPECIFICATIONS THAT MOST PIPING AND DUCTWORK BE CONCEALED. WHERE EXPOSED, RUN AS CLOSE TO CEILING AND /OR WALL AS POSSIBLE PARALLEL WITH ADJACENT STRUCTURAL OR ARCHITECTURAL ELEMENTS. EE. DO NOT INSTALL PIPING OR DUCTWORK IN ANY SWITCHGEAR, TRANSFORMER, ELEVATOR EQUIPMENT, TELEPHONE, OR ELECTRICAL EQUIPMENT ROOM, UNLESS IT IS A BRANCH SERVING THAT ROOM. FF. DO NOT INSTALL PIPING OR DUCTWORK ABOVE SWITCHBOARDS, PANELBOARDS, CONTROL PANELS, MOTOR CONTROL CENTERS, ETC. GG. ARRANGE WORK TO FACILITATE MAINTENANCE, REPAIR OR REPLACEMENT OF EQUIPMENT. PROVIDE ACCESS FOR DEVICES THAT REQUIRE MAINTENANCE. FOR CONCEALED DEVICES, VERIFY THAT ACCESS PANELS ARE PROPERLY LOCATED AND LABELED. HH. INSTALL MATERIAL AND EQUIPMENT IN ACCORDANCE WITH THE MANUFACTURER'S WRITTEN INSTRUCTIONS. II. PERFORM ALL CUTTING AND PATCHING NECESSARY TO WORK, UNLESS SPECIFICALLY DELEGATED TO THE GENERAL CONTRACTOR. OBTAIN SPECIAL PERMISSION FROM THE STRUCTURAL ENGINEER BEFORE CUTTING STRUCTURAL MEMBERS OR FINISHED MATERIAL. PERFORM ALL PATCHING IN SUCH A MANNER AS TO LEAVE NO VISIBLE TRACE AND RETURN THE AREA AFFECTED TO THE CONDITION OF UNDISTURBED WORK. PERFORM ALL PATCHING BY WORKERS EXPERIENCED, SKILLED, AND LICENSED FOR THE PARTICULAR TYPE OF WORK INVOLVED. INFERIOR WORK WILL NOT BE ACCEPTED. JJ. PATCH ALL HOLES LEFT AS A RESULT OF DEMOLITION OF MECHANICAL EQUIPMENT AND DEVICES. KK. DRILL ALL HOLES IN MASONRY WITH ROTARY DRILL. IMPACT TOOLS ARE NOT ALLOWED. CORE DRILL ALL HOLES IN MASONRY AND CONCRETE FOR MECHANICAL PENETRATIONS. PROVIDE AND DISPOSE OF ALL WATER REQUIRED FOR CORE DRILLING. COORDINATE WITH OTHER TRADES TO PREVENT DAMAGE FROM WATER. LL. PREVENT THE SPREAD OF DUST, DEBRIS, AND OTHER MATERIAL INTO ADJACENT AREAS. MM. REPLACE ALL CEILING TILES DAMAGED DURING INSTALLATION OF WORK, WITH NEW TILE. NN. REFINISH ALL MECHANICAL EQUIPMENT DAMAGED DURING SHIPPING AND /OR INSTALLATION TO ITS ORIGINAL CONDITION. REMOVE ALL RUST; PRIME, AND PAINT PER MANUFACTURER'S RECOMMENDATIONS FOR FINISH EQUAL TO ORIGINAL. 00. DO NOT USE HEATING, VENTILATING AND AIR CONDITIONING SYSTEMS PROVIDED IN THIS SCOPE OF WORK FOR TEMPORARY HEATING, VENTILATING AND AIR CONDITIONING DURING CONSTRUCTION. PP. PROTECT OPENINGS AND EQUIPMENT FROM OBSTRUCTION, BREAKAGE, MISUSE, DAMAGE OR BLEMISHES. PROTECT MATERIALS AND EQUIPMENT IMMEDIATELY UPON RECEIPT AT THE JOB SITE OR IMMEDIATELY AFTER THEY HAVE BEEN REMOVED FROM THEIR SHIPPING CONTAINERS. UNLESS NOTED OTHERWISE, KEEP THEM CLEAN AND UNDAMAGED UNTIL FINAL ACCEPTANCE OF THE ENTIRE PROJECT BY THE OWNER. WHEN A PORTION OF THE BUILDING IS OCCUPIED BY THE OWNER BEFORE SUBSTANTIAL COMPLETION OF THE ENTIRE PROJECT, MAKE ARRANGEMENTS TO TRANSFER RESPONSIBILITY FOR PROTECTION AND HOUSEKEEPING FOR THE OCCUPIED PORTION. QQ. PROTECT PIPE, DUCT AND EQUIPMENT OPENINGS WITH TEMPORARY PLUGS OR CAPS. KEEP OPENINGS COVERED UNTIL PERMANENT CONNECTIONS ARE COMPLETE. RR. CONTRACTOR IS RESPONSIBLE FOR ANY DAMAGE TO MECHANICAL EQUIPMENT, MATERIALS OR WORK UNTIL FINAL ACCEPTANCE OF THE ENTIRE PROJECT BY THE OWNER. KEEP THE PREMISES FREE FROM ACCUMULATION OF WASTE MATERIAL OR RUBBISH, CAUSED BY HIS EMPLOYEES OR WORK, AT ALL TIMES. REMOVE RUBBISH, TOOLS, SCAFFOLDING, AND SURPLUS MATERIALS FROM AND ABOUT THE BUILDING, AND LEAVE WORK AREAS "BROOM CLEAN" OR ITS EQUIVALENT UPON COMPLETION OF THE WORK. CLEAN MECHANICAL EQUIPMENT AND REMOVE TEMPORARY IDENTIFICATION. SS. IN CASE OF DISPUTE, THE OWNER WILL REMOVE THE RUBBISH AND CHARGE THE COST TO THE CONTRACTOR. TT. BEFORE START -UP, LUBRICATE, CHARGE, AND FILL SYSTEMS AS SPECIFIED AND ACCORDING TO MANUFACTURER'S INSTRUCTIONS. UU. CLEAN, DISINFECT, AND TEST ALL PLUMBING AND PIPING SYSTEMS. W. PERFORM TESTING, ADJUSTING AND BALANCING IN ACCORDANCE WITH THAT SECTION. WW. OPERATE EQUIPMENT AND SYSTEMS IN ALL THEIR OPERATING MODES, TO VERIFY PROPER OPERATION, PRIOR TO FINAL FIELD OBSERVATION AND OWNER INSTRUCTIONS. XX. ATTEND PRE - TESTING CONFERENCE AS SCHEDULED BY TESTING, ADJUSTING AND BALANCING CONTRACTOR. YY. PROVIDE ASSISTANCE TO TEST, ADJUSTING AND BALANCING CONTRACTOR BY MAKING ADJUSTMENTS TO SYSTEM AND SYSTEM COMPONENTS REQUIRED FOR ACHIEVING DESIGN PERFORMANCE. zz. AAA. BBB. CCC. DDD. EEE. IF ACCEPTABLE PERFORMANCE OF ANY TEST IS NOT ACHIEVED, MAKE THE NECESSARY CORRECTIONS AND THE TEST SHALL BE REPEATED UNTIL ACCEPTABLE PERFORMANCE IS ACHIEVED. FULLY INSTRUCT THE OWNER'S DESIGNATED PERSONNEL IN THE OPERATION OF EACH MECHANICAL SYSTEM AT THE TIME IT IS PUT INTO SERVICE. PROVIDE INSTRUCTION USING COMPETENT INSTRUCTORS AND FACTORY TRAINED PERSONNEL. INCLUDE DOCUMENTATION OF INSTRUCTIONS IN THE OPERATION AND MAINTENANCE MANUALS. OBTAIN A WRITTEN STATEMENT FROM THE OWNER THAT HIS DESIGNATED PERSONNEL HAVE BEEN INSTRUCTED. SUBMIT COMPLETED BOUND OPERATION AND MAINTENANCE MANUALS TO OWNER INCLUDING SHOP DRAWINGS, WARRANTIES, TEST REPORTS, CERTIFICATIONS, TEST AND BALANCE REPORTS, SYSTEM VALIDATION REPORTS AND RECORD DRAWINGS. ALL SUPPORTS SHALL BE FROM STRUCTURAL BEAMS AND JOISTS, NOT FROM FLOOR OR ROOF DECK ABOVE. 15025 DEMOLITION A. FURNISH LABOR, EQUIPMENT, AND MATERIALS REQUIRED FOR CUTTING, DEMOLITION, REMOVAL, PATCHING, AND RESTORATION WORK NECESSARY TO ACCOMPLISH AND COMPLETE ALL DEMOLITION, INCLUDING ANY RELOCATION OR REUSE OF EXISTING MATERIALS, EQUIPMENT, SYSTEMS, AS WELL AS THE DISPOSITION OF SALVAGED MATERIALS OR DEBRIS. ACCOMPLISH ALL WORK OF CUTTING, REMOVAL, DEMOLITION, RELOCATION, PATCHING, AND RESTORATION BY USING ONLY MECHANICS SKILLED IN THE TRADE REQUIRED. PROVIDE FOR THE SAFETY OF THE EXISTING BUILDING AND PERSONNEL, AS WELL AS FOR NEW CONSTRUCTION AS A RESULT OF WORK, PROCEDURES, OPERATIONS OR ACTIVITIES UNDER THIS CONTRACT. C. WHERE THE WORK OF REMOVALS, DEMOLITION, CUTTING AND SIMILAR WORK INVOLVES STRUCTURAL CONSIDERATIONS, CONSULT WITH STRUCTURAL ENGINEER. EXERCISE EXTREME CARE TO AVOID DAMAGE AND PRESERVE THE SAFETY OF THE STRUCTURE AND OF ALL PERSONNEL. PARTICULAR CARE MUST BE TAKEN WHERE THE DEMOLITION OR REMOVALS OCCUR ADJACENT TO OCCUPIED AREAS. D. UTILIZE COMPETENT AND QUALIFIED TECHNICAL ASSISTANCE TO DEVELOP SAFE METHODS AND TECHNIQUES TO ACCOMPLISH THE WORK, INCLUDING TEMPORARY SHORING AND SUPPORTS, METHODS OF REMOVAL AND OTHER CONSIDERATIONS. DESIGN AND PLACE ALL PERMANENT OR TEMPORARY SUPPORTS TO CARRY ALL LOADS DOWN TO SOUND BEARING. 15081 DUCTWORK INSULATION A. MATERIALS: CONFORM TO MAXIMUM FLAME SPREAD /SMOKE DEVELOPED RATING OF 25/50 IN ACCORDANCE WITH ASTM E84, NFPA 255 AND UL 723. B. CONFORM TO ASTM STANDARDS FOR "K" VALUE, MOISTURE VAPOR TRANSMISSION, MAXIMUM MOISTURE ABSORPTION, JACKET, INSULATING CEMENT, AND ADHESIVE. C. MANUFACTURER: SCHULLER - MANVILLE 800 SERIES SPIN -GLAS 1. GLASS FIBER (FLEXIBLE/RIGID): SCHULLER - MANVILLE 800 SERIES SPIN -GLAS. EQUIVALENT PRODUCTS: CERTAINTEED, KNAUF, OWENS - CORNING. 2. GLASS FIBER DUCT LINER, FLEXIBLE: SCHULLER - MANVILLE PERMACOTE LINACOUSTIC STANDARD. EQUIVALENT PRODUCTS: CERTAINTEED, KNAUF, OWENS- CORNING. 3. INSTALL IN ACCORDANCE WITH NAIMA NATIONAL INSULATION STANDARDS. D. EXHAUST AND RELIEF AIR DUCTS WITHIN 10 FT OF EXTERIOR OPENINGS: FLEXIBLE GLASS FIBER BLANKET - EXTERNAL: 1 -1/2 INCHES THICK. E. SUPPLY DUCTS - EXPOSED: NONE REQUIRED. 15083 PIPING INSULATION A. CONFORM TO MAXIMUM FLAME SPREAD /SMOKE DEVELOPED RATING OF 25/50 IN ACCORDANCE WITH ASTM E84, NFPA 255 AND UL 723. B. CONFORM TO ASTM STANDARDS FOR "K" VALUE, MOISTURE VAPOR TRANSMISSION, MAXIMUM MOISTURE ABSORPTION, JACKET, INSULATING CEMENT, AND ADHESIVE. C. MANUFACTURER:GLASS FIBER: SCHULLER - MANVILLE,CERTAINTEED, KNAUF, OWENS - CORNING. 1. CELLULAR FOAM: ARMSTRONG, HALSTEAD, IMCOA/NOMACO, RUBATEX, ARMAFLEX 2000. D. INSTALL IN ACCORDANCE WITH NAIMA NATIONAL INSULATION STANDARDS. VERIFY THAT PIPING HAS BEEN TESTED BEFORE APPLYING INSULATION MATERIALS. VERIFY THAT SURFACES ARE CLEAN AND DRY, WITH FOREIGN MATERIAL REMOVED. E. CONTINUE INSULATION THROUGH WALLS, SLEEVES, PIPE HANGERS, AND OTHER PIPE PENETRATIONS. FINISH AT SUPPORTS, PROTRUSIONS, AND INTERRUPTIONS. F. BURIED PIPING: PROVIDE FACTORY FABRICATED ASSEMBLY WITH INNER ALL- PURPOSE SERVICE JACKET WITH SELF - SEALING LAP, AND ASPHALT IMPREGNATED OPEN MESH GLASS FABRIC, WITH ONE MIL THICK ALUMINUM FOIL SANDWICHED BETWEEN THREE LAYERS OF BITUMINOUS COMPOUND; OUTER SURFACE FACED WITH A POLYESTER FILM. G. SCHEDULE: INSULATION THICKNESS PER LOCAL CODE OR ASHRAE STANDARD 90.1 -1999, WHICHEVER IS MORE STRINGENT. 15100 PLUMBING PIPING A. SANITARY PIPING. 1. CAST IRON PIPE: ASTM T A74 SERVICE WEIGHT, FITTINGS: CAST IRON, JOINTS: HUB-AND-SPIGOT, COMPRESSION TYPE WITH NEOPRENE GASKETS OR LEAD AND OAKUM. 2. CAST IRON PIPE: CISPI 301, HUBLESS, FITTINGS: CAST IRON, JOINTS: NEOPRENE GASKET AND STAINLESS STEEL CLAMP AND SHIELD ASSEMBLIES. 3. ABS PIPE ( BELOW GRADE): ASTM D2661, FITTINGS: ABS, JOINTS: SOLVENT WELD. 4. COPPER TUBE (ABOVE GRADE): ASTM B88 TYPE "L ", HARD TEMPER ONLY. EXCEPT THESE MATERIALS SHALL NOT BE USED TO RECEIVE THE WASTES FROM URINALS NOR WASTES FROM WATER CLOSETS IN BATTERY, FITTINGS: CAST BRONZE, OR WROUGHT COPPER, JOINTS: SOLDER, GRADE 50B. B. WATER PIPING. 1. COPPER TUBING (BELOW GRADE): ASTM B88, TYPE "K" SOFT COPPER, FITTINGS: CAST COPPER ALLOY OR WROUGHT COPPER C - PPER AND BRONZE, JOINTS: BCUP SILVER BRAZE. 2. COPPER TUBING (ABOVE GRADE): ASTM B88, TYPE 'L" HARD DRAWN, FITTINGS: CAST COPPER ALLOY OR WROUGHT COPPER AND BRONZE, JOINTS: BCUP SILVER BRAZE. C. VERIFY THAT EXCAVATIONS ARE TO REQUIRED GRADE, DRY, AND NOT OVER- EXCAVATED. D. PREPARE PIPING CONNECTIONS TO EQUIPMENT WITH FLANGES OR UNIONS. E. PROVIDE NON - CONDUCTING DIELECTRIC CONNECTIONS WHEREVER JOINTING DISSIMILAR METALS. F. INSTALL VENT PIPING PENETRATING ROOFED AREAS TO MAINTAIN INTEGRITY OF ROOF ASSEMBLY. G. WHERE PIPE SUPPORT MEMBERS ARE WELDED TO STRUCTURAL BUILDING FRAMING, SCRAPE, BRUSH CLEAN, AND APPLY ONE COAT OF ZINC RICH PRIMER TO WELDING. H. PROVIDE SUPPORT FOR UTILITY METERS IN ACCORDANCE WITH REQUIREMENTS OF UTILITY COMPANIES. I. PREPARE EXPOSED, UNFINISHED PIPE, FITTINGS, SUPPORTS, AND ACCESSORIES READY FOR FINISH PAINTING. J. SLEEVE PIPES PASSING THROUGH PARTITIONS, WALLS AND FLOORS. K. USE GROOVED MECHANICAL COUPLINGS AND FASTENERS ONLY IN ACCESSIBLE LOCATIONS. L. PROVIDE UNIONS DOWNSTREAM OF VALVES AND AT EQUIPMENT OR APPARATUS CONNECTIONS. M. PROVIDE BRASS MALE ADAPTERS EACH SIDE OF VALVES IN COPPER PIPED SYSTEM. SOLDER ADAPTERS TO PIPE. N. ESTABLISH INVERT ELEVATIONS, SLOPES FOR DRAINAGE TO 1/4 INCH PER FOOT (SMALLER THAN 3 INCH PIPE), AND 1/8 INCH PER FOOT (3 INCHES AND LARGER) MINIMUM. MAINTAIN GRADIENTS. 0. SLOPE WATER PIPING MINIMUM 0.25 PERCENT AND ARRANGE TO DRAIN AT LOW POINTS. P. PROVIDE NEW SANITARY SEWER SERVICES. BEFORE COMMENCING WORK CHECK INVERT ELEVATIONS REQUIRED FOR SEWER CONNECTIONS, CONFIRM INVERTS AND ENSURE THAT THESE CAN BE PROPERLY CONNECTED WITH SLOPE FOR DRAINAGE AND COVER TO AVOID FREEZING. Q. PROVIDE SUPPORT AND EQUIPMENT REQUIRED TO CONTROL EXPANSION AND CONTRACTION OF PIPING. PROVIDE LOOPS, PIPE OFFSETS, AND SWING JOINTS, OR EXPANSION JOINTS WHERE REQUIRED. R. PROVIDE HANGERS IN QUANTITY AND SPACING REQUIRED TO SUFFICIENTLY SUPPORT PIPING. 15110 VALVES & PLUMBING SPECIALTIES A. MANUFACTURERS: 1. GATE VALVES (UP TO AND INCLUDING 2 "): STOCKHAM MODEL B -105, OR EQUIVALENT BY: a. HAMMOND, KITZ, MILWAUKEE, NIBCO, CRANE. 2. BALL VALVES (UP TO AND INCLUDING 2 "): APOLLO 77- 100/77 -200 SERIES, OR EQUIVALENT BY: a. HAMMOND, KITZ, MILWAUKEE, NIBCO, WATTS, CRANE. 3. SWING CHECK VALVES (UP TO AND INCLUDING 2- 1/2 "): STOCKHAM MODEL B -309/B -319, OR EQUIVALENT BY: a. HAMMOND, KITZ, MILWAUKEE, NIBCO, CRANE. 4. TEMP. AND PRESS. RELIEF VALVE (UP TO 80,000 BTU INPUT): WATTS 10L MODEL M7 B. C. ., 6. REDUCED PRESSURE ZONE (RPZ) BACKFLOW PREVENTER: WATTS SERIES 909 7. RPZ AIR GAP FITTING: WATTS 909AG 8. RPZ AIR GAP VENT ELBOW: WATTS 909EL (REQUIRED IN ADDITION TO 909AG IF MID. VERTICALLY). 10. VACUUM BREAKER: WATTS N36 - %" 11. PRESSURE REDUCING VALVE: WATTS SERIES U5 12. ATMOSPHERIC VACUUM BREAKER: WATTS SERIES 288A 13. HOSE END VACUUM BREAKER: WATTS SERIES 8 14. DIELECTRIC UNION: WATTS SERIES 3000 15. TRAP SEAL PRIMER VALVE: JOSAM 88250, OR EQUIVALENT BY: A. J.R. SMITH, WADE, ZURN INSTALL APPROVED POTABLE WATER PROTECTION DEVICES ON PLUMBING LINES WHERE CONTAMINATION OF DOMESTIC WATER MAY OCCUR; JANITOR ROOMS, FIRE SPRINKLER SYSTEMS, PREMISE ISOLATION. INSTALL WATER HAMMER ARRESTORS COMPLETE WITH ACCESSIBLE ISOLATION VALVE ON HOT AND COLD WATER SUPPLY PIPING WHERE REQUIRED BY CODE AND PER MANUFACTURERS RECOMMENDATIONS /REQUIREMENTS. n D. INSTALL AIR CHAMBERS ON HOT AND COLD WATER SUPPLY PIPING TO EACH FIXTURE OR GROUP OF FIXTURES (EACH WASHROOM). FABRICATE SAME SIZE AS SUPPLY PIPE OR 3/4 INCH MINIMUM, AND MINIMUM 18 INCHES LONG. 15325 SPRINKLER SYSTEMS A. CONTRACTOR SHALL DESIGN AND CALCULATE THE NEW AND RENOVATION OF EXISTING PIPING SYSTEMS, INCLUDING PIPE SCHEDULE, LOCATION OF ALL VALVES, DEVICES, AND SPRINKLER HEADS. DESIGN SPRINKLER SYSTEM PIPING BASED ON HAZARD RATING AS OF THE MOST STRINGENT OF THE REGULATING AGENCIES RESPONSIBLE FOR THIS FACILITY, INCLUDING THE OWNER INSURANCE COMPANY REQUIREMENTS AND THE GOVERNING AUTHORITIES, FM OR AS DETERMINED BY LOCAL REQUIREMENTS. PERFORM WORK IN ACCORDANCE WITH NFPA 13. B. SUBMIT SHOP DRAWINGS, PRODUCT DATA, AND CALCULATIONS TO AUTHORITY HAVING JURISDICTION, AND OWNER'S INSURANCE UNDERWRITER FOR APPROVAL. SUBMIT PROOF OF APPROVAL TO ARCHITECT/ENGINEER. C. PROVIDE EXTRA SPRINKLERS UNDER PROVISIONS OF NFPA 13. D. PROVIDE SUITABLE WRENCHES FOR EACH SPRINKLER TYPE. E. PROVIDE METAL STORAGE CABINET FOR EXTRA SPRINKLERS LOCATED ADJACENT TO THE VALVE ASSEMBLY. F. SPRINKLER MANUFACTURERS: AUTOMATIC SPRINKLER OF AMERICA, RELIABLE AUTOMATIC SPRINKLER COMPANY, STAR SPRINKLER COMPANY, VIKING CORPORATION. G. INSTALL SYSTEM IN ACCORDANCE WITH NFPA 13. H. INSPECTOR'S TEST CONNECTION: FOR EACH SPRINKLER SYSTEM AND FOR EACH WATERFLOW ALARM DEVICE, WHERE MULTIPLE DEVICES OCCUR, PROVIDE AN INSPECTOR'S TEST ASSEMBLY. I. WATER CURTAINS AT NON -RATED OPENINGS: 1. INSTALL SPRINKLER HEADS ON 6 FOOT CENTERS TO PROVIDE A WATER CURTAIN AT NON -FIRE RATED DOORS AND WINDOWS. LOCATE SPRINKLER HEADS WITHIN 1 FOOT OF THE DOOR OR WINDOW ON BOTH SIDES OF THE DOOR AND WINDOW. 2. SPRINKLER HEADS ARE TO BE SUPPLIED FROM THE WET OVERHEAD SPRINKLER SYSTEM. 3. WATER CURTAIN SPRINKLER HEADS ARE TO BE CALCULATED AS A PART OF THE OVERHEAD WET SPRINKLER SYSTEM WITH A MINIMUM DESIGN DISCHARGE OF 3 GPM PER LINEAL FOOT WITH NO SPRINKLER DISCHARGING LESS THAN 15 GPM. MINIMUM PRESSURE AT A SPRINKLER HEAD IS TO BE 7 PSI. J. EXISTING FIRE PROTECTION SYSTEMS: 1. IN BUILDINGS WITH EXISTING FIRE PROTECTION SYSTEMS, THE CONTRACTOR SHALL CLOSELY COORDINATE HIS WORK WITH THE OWNER TO MINIMIZE DISRUPTION OF THAT SYSTEM. 2. NO FIRE PROTECTION SYSTEM IS TO REMAIN DEACTIVATED AT THE END OF THE WORK DAY UNLESS AGREED TO WITH THE PROPERTY OWNER, AND A SUITABLE FIRE PROTECTION SCHEME SUCH AS A MANNED FIRE WATCH, HAS BEEN IMPLEMENTED AND APPROVED BY THE OWNER. IT IS THE CONTRACTOR'S RESPONSIBILITY TO SEE THAT ALL FIRE PROTECTION SYSTEMS ARE FILLED, AND THE SYSTEM FUNCTIONAL BEFORE COMPLETING HIS WORK DAY. K. CENTER SPRINKLERS IN ONE DIRECTION ONLY IN CEILING TILE WITH LOCATION IN OTHER DIRECTION VARIABLE, DEPENDENT UPON SPACING AND COORDINATION WITH CEILING ELEMENTS. L. ENSURE REQUIRED DEVICES ARE INSTALLED AND CONNECTED AS REQUIRED TO FIRE ALARM SYSTEM. M. COORDINATE PIPING WITH STRUCTURAL, MECHANICAL PIPING AND DUCTWORK, AND ELECTRICAL WITHIN THE BUILDING. PIPING CONFLICTS BETWEEN SYSTEM SHALL BE REMOVED AND REPLACED AT NO COST TO THE OWNER. N. CONDUCT ALL APPLICABLE TESTS AS REFERENCED IN NFPA STANDARD 13. ALL NECESSARY TESTS SHALL BE CONDUCTED IN CONFORMANCE WITH REQUIREMENTS OF NFPA. 0. SPRINKLER HEAD LOCATIONS ARE FOR REFERENCE ONLY. THE FINAL LOCATIONS NEED TO BE INSTALLED PER CODE AND ARE THE RESPONSIBILITY OF THE CONTRACTOR WHO INSTALLS. P. TENANT FIRE SERVICE MAIN WITH BRANCH PIPING STUBBED INTO TENANT'S SPACE PROVIDED BY LANDLORD. LANDLORD'S SPRINKLER SYSTEM IS DESIGNED PER ORDINARY HAZARD GROUP 2 AND THE LATEST REQUIREMENTS OF NFPA -13. NO ISOLATION VALVES WILL BE PROVIDED OR PERMITTED. Q. CONTRACTOR SHALL CONNECT FIRE SPRINKLER SYSTEM TO LANDLORD SPRINKLER SYSTEM WITHIN THE DEMISED PREMISES USING APPROVED MECHANICAL FITTINGS. CONTRACTOR SHALL PROVIDE AND INSTALL ALL BRANCH PIPING AND SPRINKLERS REQUIRED TO COMPLETE THE SPRINLKER SYSTEM WITHN THE TENANT SPACE. SPRINKLER SYSTEM DESIGNS SHALL BE BASED UPON THE REQUIREMENTS OF THE STATE OF WASHINGTON, CITY OF TUKWILA FIRE DEPARTMENT. TENANT SHALL ENGAGE THE SERVICES OF A LANDLORD PREFERED FIRE SPRINKLER CONTRACTOR TO DESIGN, PERMIT AND INSTALL TENANT'S FIRE SPRINKLER SYSTEM IN ACCORDANCE WITH THE BASE BUILDING DESIGN SPECIFICATIONS. SPRINKLER LAYOUT AND PIPE SIZING SHALL BE HYDRAULICALLY DESIGNED ACCORDING TO ORDINARY HAZARD GROUP 2 AND THE LATEST REQUIREMENTS OF NFPA -13. TENANT SPACE SPRINKLER SYSTEM WITH 20 SPRINKLER HEADS OR LESS SHALL NOT REQUIRE HYDRAULLIC CALCULATIONS. 15410 PLUMBING FIXTURES AND EQUIPMENT A. MANUFACTURERS: 1. WATER CLOSETS; AMERICAN STANDARD, CRANE, ELJER, KOHLER. 2. LAVATORIES; AMERICAN STANDARD, CRANE, ELJER, KOHLER. 3. ELECTRIC WATER COOLERS; ELKAY, HALSEY TAYLOR, HAWS, OASIS. 4. SERVICE SINKS; FIAT, AMERICAN STANDARD, CRANE, ELJER, KOHLER. 5. FAUCETS (LAVATORIES): AMERICAN STANDARD, CRANE, ELJER, KOHLER, DELTA, MOEN, CHICAGO FAUCET, ZURN. 6. FAUCETS (SERVICE SINKS -): FIAT, MUSTEE, STERN - WILLIAMS, SWAN, CHICAGO FAUCET, ZURN. 7. SEATS: BEMIS, BENEKE, CHURCH, OLSONITE, SPERZEL. 8. CARRIERS: JOSAM, JONESPEC, J.R. SMITH, WADE, ZURN. 9. INSULATION KITS: TRUEBRO, BROCAR, PLUMBEREX SPECIALTY PRODUCTS. 10. RECEPTORS (FLOOR DRAINS, ETC..) JOSAM, J.R. SMITH, WADE, ZURN. 11. FLOOR/WALL CLEANOUTS: JOSAM, J.R. SMITH, WADE, ZURN. 12. WATER HEATERS (TANK TYPE): A.Q. SMITH, RHEEM/RUUD, STATE. PROVIDE BRACKETS, BRACES OR REINFORCING ANGLES AS REQUIRED IN ALL PARTITIONS NOT SUFFICIENT IN THEMSELVES TO SUPPORT PLUMBING FIXTURES OR OTHER WALL -HUNG EQUIPMENT. C. INSTALL EACH FIXTURE WITH CHROME PLATED, 17 GAUGE TUBING TRAP WITH CLEANOUT, EASILY REMOVABLE FOR SERVICING AND CLEANING. D. INSTALL COMPONENTS LEVEL, PLUMB AND SECURE. E. INSTALL AND SECURE FIXTURES IN PLACE WITH WALL CARRIERS AND BOLTS. F. SEAL FIXTURES TO WALL AND FLOOR SURFACES WITH SEALANT, COLOR TO MATCH FIXTURE. G. MOUNT LEVER CONTROL FOR HANDICAPPED WATER CLOSETS ON WIDE SIDE OF TOILET STALL. H. INSULATE WASTE AND SUPPLIES FOR ALL HANDICAPPED FIXTURES. I. ROUGH -IN FIXTURE PIPING CONNECTIONS IN ACCORDANCE WITH MINIMUM SIZES INDICATED IN PLUMBING FIXTURE SCHEDULE ON DRAWINGS. J. REVIEW MILLWORK SHOP DRAWINGS. CONFIRM LOCATION AND SIZE OF FIXTURES AND OPENINGS BEFORE ROUGH -IN AND INSTALLATION. K. EXPOSED WATER PIPING CHROME PLATED BRASS. 15810 DUCTWORK A. PERFORM WORK IN ACCORDANCE WITH SMACNA - HVAC DUCT CONSTRUCTION STANDARDS - METAL AND FLEXIBLE, UNLESS MORE STRINGENT REQUIREMENTS ARE NOTED IN LOCAL CODES. B. GALVANIZED STEEL DUCTS: ASTM A525 AND ASTM A527 GALVANIZED STEEL SHEET, LOCK - FORMING QUALITY, HAVING G60 ZINC COATING OF IN CONFORMANCE WITH ASTM A90. C. INSULATED FLEXIBLE DUCTS: 1. MANUFACTURERS: FLEX -AIRE, FLEXMASTER, NORFLEX, THERMAFLEX, WIREMOLD. 2. TWO PLY VINYL FILM SUPPORTED BY HELICALLY WOUND SPRING STEEL WIRE; FIBERGLASS INSULATION; POLYETHYLENE VAPOR BARRIER FILM. PRESSURE RATING: 10 INCHES WG POSITIVE AND 1.0 INCHES WG NEGATIVE. MAXIMUM VELOCITY: 4000 FPM. TEMPERATURE RANGE: -10 DEGREES F TO 160 DEGREES F. D. FABRICATE AND SUPPORT IN ACCORDANCE WITH SMACNA HVAC DUCT CONSTRUCTION STANDARDS - METAL AND FLEXIBLE, UNLESS MORE STRINGENT REQUIREMENTS ARE NOTED IN LOCAL CODES. E. INSTALLATION - GENERAL: 1. INSTALL AND SEAL DUCTS IN ACCORDANCE WITH SMACNA HVAC DUCT CONSTRUCTION STANDARDS - METAL AND FLEXIBLE, UNLESS MORE STRINGENT REQUIREMENTS ARE NOTED IN LOCAL CODES. 2. SUPPORT DUCTWORK IN ACCORDANCE WITH SMACNA HVAC DUCT CONSTRUCTION STANDARDS - METAL AND FLEXIBLE, CHAPTER 4, HANGERS AND SUPPORTS. 3. PROVIDE FIRESTOP SYSTEMS FOR PIPE AND DUCT THROUGH - PENETRATIONS OF THE FOLLOWING FIRE - RESISTANCE -RATED ASSEMBLIES, INCLUDING BOTH EMPTY OPENINGS AND OPENINGS CONTAINING PENETRATING ITEMS: FLOOR AND CEILINGS, WALLS AND PARTITIONS, SMOKE BARRIERS, AND CONSTRUCTION ENCLOSED COMPARTMENTALIZED AREAS. 4. DUCT HANGERS SHALL NOT ATTACH TO BOTTOM CHORD OF STEEL JOIST OR METAL ROOF DECKING. ATTACH TO TOP CHORD OF STEEL JOIST. 5. CONNECT DIFFUSERS OR LIGHT TROFFER BOOTS TO LOW PRESSURE DUCTS DIRECTLY OR WITH 3 FEET MAXIMUM LENGTH OF FLEXIBLE DUCT HELD IN PLACE WITH STRAP OR CLAMP. F. PROTECTION: DURING CONSTRUCTION, PROVIDE TEMPORARY CLOSURES OF METAL OR TAPED POLYETHYLENE ON OPEN DUCTWORK TO PREVENT CONSTRUCTION DUST FROM ENTERING DUCTWORK SYSTEM. G. CLEANING: 1. CLEAN DUCT SYSTEM AND FORCE AIR AT HIGH VELOCITY THROUGH DUCT TO REMOVE ACCUMULATED DUST. TO OBTAIN SUFFICIENT AIR, CLEAN HALF THE SYSTEM AT A TIME. PROTECT EQUIPMENT WHICH MAY BE HARMED BY EXCESSIVE DIRT WITH TEMPORARY FILTERS, OR BYPASS DURING CLEANING. 2. CLEAN DUCT SYSTEMS WITH HIGH POWER VACUUM MACHINES. PROTECT EQUIPMENT WHICH MAY BE HARMED BY EXCESSIVE DIRT WITH FILTERS, OR BYPASS DURING CLEANING. 15820 DUCTWORK ACCESSORIES A. INSTALL ACCESSORIES IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS, NFPA 90A, AND FOLLOW SMACNA HVAC DUCT CONSTRUCTION STANDARDS - METAL AND FLEXIBLE. B. INSTALL CONTROL DAMPERS FURNISHED IN SECTION 15906. C. PROVIDE BACKDRAFT DAMPERS ON EXHAUST FANS OR EXHAUST DUCTS NEAREST TO OUTSIDE AND WHERE INDICATED. 15840 VARIABLE VOLUME BOX A. FURNISH ELECTRONICALLY CONTROLLED, FAN POWERED, SINGLE DUCT, VARIABLE VOLUME AIR DISTRIBUTION ASSEMBLIES WITH ATTENUATOR OF THE CAPACITIES LISTED ON VAV SCHEDULE. B. EACH ASSEMBLY SHALL BE PRESSURE INDEPENDENT. THAT IS, IT SHALL PROVIDE AIR FLOW REGULATION WITHIN +/- 50FPM, REGARDLESS OF DUCT PRESSURE FLUCTUATION, THROUGHOUT ITS ENTIRE RATED CFM RANGE. EACH ASSEMBLY SHALL RESET TO ANY AIR FLOW BETWEEN ZERO AND THE MAXIMUM CATALOGED CFM WITHOUT CHANGING ORIFICES OR OTHER PARTS. CFM LIMITERS WILL NOT BE ACCEPTED. C. AT AN INLET VELOCITY OF 2000 FPM, THE DIFFERENTIAL STATIC PRESSURE FOR ANY SIZE SHALL NOT EXCEED 0.15" WG FOR THE BASIC ASSEMBLY, OR 0.45" WITH THE SOUND ATTENUATOR ADDED. D. EACH BASIC ASSEMBLY SHALL CONTAIN AN ACOUSTICAL VORTEX SHEDDER. E. THE AIR DISTRIBUTION ASSEMBLY SHALL BE DESIGNED TO MAINTAIN ESSENTIALLY CONSTANT AIR FLOW REGARDLESS OF INLET FLOW VARIATIONS. A HARD DUCT ELBOW OF ANY ANGLE UP TO 90 DEGREES SHALL NOT ALTER THE MAXIMUM OR MINIMUM FACTORY AIR FLOW SETTING BY MORE THAN 10 %. F. THE ELECTRONIC AIR FLOW SENSOR SHALL BE INDEPENDENT OF DUCT AIR TEMPERATURES FROM 50 TO 120 F OVER A VELOCITY RANGE OF 0 -3000 FPM. G. THE ELECTRONIC CONTROLLER SHALL BE CALIBRATED AND THE FACTORY SET FOR THE MAXIMUM AND MINIMUM AIR FLOW RATES AS SCHEDULED. FIELD CALIBRATION AND READJUSTMENT SHALL BE PROVIDED FOR THE CONTROLLER SHALL BE FITTED WITH AN EXTERNAL TERMINAL BOARD ON WHICH ALL FIELD CONNECTIONS ARE MADE. ALL TERMINALS SHALL BE CLEARLY LABELED. H. THE ELECTRONIC ROOM THERMOSTAT SHALL HAVE A SET POINT RANGE OF 65 TO 85 F AND A THROTTLING RANGE OF 2 F ± 20 %. I. THE ELECTRIC ACTUATOR SHALL EXERT POSITIVE FORCE IN BOTH THE OPENING AND CLOSING DIRECTIONS; SPRING RETURN TYPES WILL NOT BE ACCEPTED. THE ACTUATOR SHALL INCLUDE BUILT -IN LIMITS TO INTERRUPT THE CURRENT TO THE ACTUATOR AT THE STROKE LIMIT IN EACH DIRECTION. THE ACTUATOR SHALL BE ENERGIZED ONLY WHEN THE CONTROLLER SIGNALS A CHANGE IN DAMPER POSITION. THE ELECTRIC ACTUATOR SHALL BE VARIABLE SPEED, DC CONTROLLED. J. THE AIR DISTRIBUTION ASSEMBLY SHALL OPERATE ON A SINGLE OUTSIDE POWER SOURCE OF 6 WATTS, 60 HERTZ, 24 VOLTS AC + 15 %, -10 %. K. THE ASSEMBLY CASING SHALL BE CONSTRUCTED OF 20 GAUGE GALVANIZED STEEL, INTERNALLY LINED WITH 1 INCH, 1 -1/2 POUND DENSITY FIBERGLASS INSULATION WHICH COMPLIES WITH U.L.. -181 AND NFPA 90A. BOTTOM ACCESS PANEL FOR FAN SERVICE. L. THE DAMPER SHALL BE OF HEAVY GAUGE CONSTRUCTION WITH BLADES PIVOTED IN DELRIN SELF - LUBRICATING BEARINGS. THE BLADES SHALL SEAL WITH LESS THAN 2% LEAKAGE AT 3 INCHES SP, AS RATED BY AIR DIFFUSION COUNCIL TEST CODE 1062 R4. M. BASE BID SHALL BE AS MANUFACTURED BY TITUS, ALTERNATE ADD OR DEDUCT SHALL BE ACCEPTED AS MANUFACTURED BY CARNES. N. FAN SHALL BE CONSTRUCTED OF STEEL AND HAVE A FORWARD CURVED, DYNAMICALLY BALANCED WHEEL WITH DIRECT DRIVE MOTOR. TERMINALS SHALL INCLUDE GASKETTED BACKDRAFT DAMPER AT FAN DISCHARGE TO PREVENT PRIMARY AIRFLOW FROM FLOWING BACK THROUGH FAN SECTION. 15850 AIR OUTLETS AND INLETS A. GRILLES, REGISTERS AND DIFFUSERS: 1. MANUFACTURERS: ANEMOSTAT, KRUEGER, METALAIRE, NAILOR, PRICE, TITUS, TUTTLE & BAILEY. B. GOOSENECKS 1. FABRICATE IN ACCORDANCE WITH SMACNA HVAC DUCT CONSTRUCTION STANDARDS - METAL AND FLEXIBLE, OF MINIMUM 18 GAGE GALVANIZED STEEL. 2. MOUNT ON MINIMUM 12 INCH HIGH CURB BASE WHERE SIZE EXCEEDS 9 X 9 INCH. 15906 AUTOMATIC CONTROLS (VAV) A. THE TERMINAL UNIT MANUFACTURER SHALL PROVIDE PRESSURE INDEPENDENT ANALOG ELECTRONIC CONTROLS WHICH CAN BE RESET TO MODULATE AIRFLOW BETWEEN AND THE MAXIMUM CATALOGED CFM. B. THE TERMINAL UNIT SHALL INCORPORATE A MULTI - POINT, CENTER AVERAGING VELOCITY SENSOR. THE SENSOR MUST PROVIDE A MINIMUM DIFFERENTIAL PRESSURE SIGNAL OF 0.03 "WG AT AN INLET VELOCITY OF 500FPM. THE SENSOR MUST PROVIDE CONTROL SIGNAL ACCURACY OF +/ -5 %, WITH THE SAME INLET SIZE AT ANY INLET CONNECTION. C. THE VELOCITY CONTROLLER SHALL HAVE A CONSTANT 2 °F RESET SPAN REGARDLESS OF MINIMUM AND MAXIMUM AIR FLOW LIMITS. THE CONTROLLER SHALL ALLOW FLOW ADJUSTMENTS TO BE MADE AND MONITORED FROM MATCHED THERMOSTAT. IN ADDITION, THE THERMOSTAT SHALL PROVIDE A LIVE VELOCITY READOUT TERMINAL. THE THERMOSTAT SHALL HAVE CONCEALED COVER LATCHES AND TEMPERATURE SETPOINT SLIDERS TO PREVENT TAMPERING. VELOCITY CONTROLLER AND THERMOSTAT ARE BY TERMINAL MANUFACTURER. D. CONTROL DEVICES -HALL BE FACTORY SET FOR THE SCHEDULED MINIMUM AND MAXIMUM FLOW RATES. VELOCITY MEASURING POINTS WILL BE INTEGRATED WITH THE THERMOSTAT FOR FIELD BALANCING AIRFLOW. ALL PNEUMATIC TUBES SHALL BE UL LISTED FIRE RETARDANT (FR) TYPE. EACH TERMINAL SHALL BE EQUIPPED WITH LABELING SHOWING UNIT LOCATION, SIZE, AND MINIMUM AND MAXIMUM CFM SETPOINTS. E. THE TERMINAL MANUFACTURER SHALL PROVIDE A 24 VAC REVERSIBLE L DAMPER ACTUATOR. THE ACTUATOR SHALL BE A DIRECT - COUPLED, SHAFT - MOUNTED TYPE WITHOUT EXTERNAL LINKAGES. A MAGNETIC CLUTCH AND LINKAGE RELEASE BUTTON SHALL BE INTEGRAL TO THE ACTUATOR. THE DAMPER SHALL BE FACTORY SET IN AN OPEN POSITION. F. THE TERMINAL MANUFACTURER SHALL PROVIDE A CLASS 2, 24 VAC CONTROL VOLTAGE TRANSFORMER WITH INTERNAL CURRENT LIMITING PROTECTION. ALL CONTROLS SHALL BE INSTALLED IN APPROVED NEMA 1 ENCLOSURE. ALL COMPONENTS MUST BE COMPATIBLE FOR USE WITH GROUNDED CONTROL CIRCUITS PER UL 1995. G. SEQUENCE OF OPERATION: VAV BOX: 1. COOLING CYCLE - OCCUPIED HOURS: UPON A RISE IN SPACE TEMPERATURE ABOVE THE OCCUPIED SETPOINT OF THE THERMOSTAT, THE VAV BOX SHALL MODULATE THE PRIMARY AIR AS REQUIRED TO MAINTAIN SPACE TEMPERATURE AT THE THERMOSTAT SETPOINT. FAN SHALL BE OFF. 2. HEATING CYCLE - OCCUPIED HOURS: UPON A DROP IN SPACE TEMPERATURE BELOW THE OCCUPIED HEATING SETPOINT OF THE THERMOSTAT, THE VAV BOX SHALL MODULATE TO DECREASE PRIMARY AIRFLOW DOWN TO THE MINIMUM AIRFLOW. FAN SHALL BE ON. 3. COOLING CYCLE - UNOCCUPIED HOURS: UPON A RISE IN NIGHT SETBACK SPACE TEMPERATURE ABOVE THE UNOCCUPIED COOLING SETPOINT OF THE THERMOSTAT, THE VAV BOX SHALL MODULATE AS REQUIRED TO MAINTAIN SPACE TEMPERATURE AT THE THERMOSTAT SETPOINT. FAN SHALL BE OFF. 4. HEATING CYCLE -- UNOCCUPIED HOURS: UPON A DROP IN NIGHT SETBACK SPACE TEMPERATURE BELOW THE UNOCCUPIED HEATING SETPOINT OF THE THERMOSTAT, THE VAV BOX SHALL MODULATE TO DECREASE PRIMARY AIRFLOW DOWN TO THE MINIMUM AIRFLOW. CYCLE FAN TO MAINTAIN TEMPERATURE SET POINT. 15950 TESTING, ADJUSTING, AND BALANCING A. WORK INCLUDES 1. TESTING, ADJUSTMENT, AND BALANCING OF NEW AND EXISTING AIR SYSTEMS. 2. MEASUREMENT OF FINAL OPERATING CONDITION OF HVAC SYSTEMS. B. SERVICES PROVIDED BY QUALIFIED PERSONNEL OF MECHANICAL CONTRACTOR OR INDEPENDENT QUALIFIED TESTING AND BALANCING AGENCY. C. PERFORM TOTAL SYSTEM BALANCE IN ACCORDANCE WITH AABC NATIONAL STANDARDS FOR FIELD MEASUREMENT AND INSTRUMENTATION, TOTAL SYSTEM BALANCE OR NEBB PROCEDURAL STANDARDS FOR TESTING, BALANCING AND ADJUSTING OF ENVIRONMENTAL SYSTEMS. D. VERIFY THAT SYSTEMS ARE COMPLETE AND OPERABLE BEFORE COMMENCING WORK. E. AIR HANDLING SYSTEMS: ADJUST TO WITHIN PLUS OR MINUS 5 PERCENT OF DESIGN FOR SUPPLY SYSTEMS AND PLUS OR MINUS 10 PERCENT OF DESIGN FOR RETURN AND EXHAUST SYSTEMS. ADJUST OUTSIDE AIR TO WITHIN 0 TO PLUS 10 PERCENT OF DESIGN. F. AIR OUTLETS AND INLETS: ADJUST TOTAL TO WITHIN PLUS 10 PERCENT AND MINUS 5 PERCENT OF DESIGN TO SPACE. ADJUST OUTLETS AND INLETS IN SPACE TO WITHIN PLUS OR MINUS 10 PERCENT OF DESIGN. G. ADJUST AIR HANDLING AND DISTRIBUTION SYSTEMS TO PROVIDE REQUIRED OR DESIGN SUPPLY, RETURN, OUTSIDE AIR, AND EXHAUST AIR QUANTITIES. H. SUBMIT COPIES OF T &B REPORT TO LANDLORD, OWNER, AND ENGINEER. K ithW U9) i-OR CODE COMPLIANCE AA PR VET) AL :.':3 1. 2008 City Of Tukwila TC9o8-)i)1 DATE: JOB NO: DRAWN: 07/08/08 08- 0196.004 MDB CHECKED: SAC 711 N. FIELDER RD. ARLINGTON, TX 76012 PH: (817) 635 -5696 FAX: (817) 635 -5699 10 u ua a J ce pip a 0 co ce � W W 4zt ,y,zz ww L.) 11-1 to » 00 I- rv) RECEIVE AUG 13 2000 PERMIT CENTER HALL , ENGINEERIbLG Mechanical /Electrical Consulting Engineers 1750 Commerce Court, White Bear Lake, MN 55110 (651) 748 -1100 • Fax (651) 748 -9370 REVISIONS 1. LANDLORD REVISIONS - 07/10/08 2. PLUMBING DIVISION REVISIONS - 08/05/08 MECHANICAL SPECIFICATIONS SHEET NUMBER M3 ELECTRICAL SYMBOLS LIGHT FIXTURE DESCRIPTION MOUNTING WIRING DEVICE DESCRIPTION MOUNTING COMMUNICATIONS DESCRIPTION OUNTING Mounting: Surface RECEPTACLE OPTIONS DENOTED BY "X ", WHERE "X" CAN BE ONE OF THE FOLLOWING: IG = ISOLATED GROUND GFI = GROUND FAULT INTERRUPTER TR = TAMPER RESISTANT SS = SURGE SUPPRESSOR WP = WEATHERPROOF (blank) = STANDARD RECEPTACLE -e x SIMPLEX RECEPTACLE, NORMAL POWER 18" x DUPLEX RECEPTACLE, NORMAL POWER 18" x DUPLEX RECEPTACLE, UPS POWER 18" : X DUPLEX RECEPTACLE, EMERGENCY POWER 18" x �3Q x FOURPLEX RECEPTACLE 18 0 FLOOR OUTLET BOX, POWER, VOICE AND /OR DATA 40-30R SPECIAL PURPOSE RECEPTACLE, WITH NEMA CONFIGURATION NOTED 18" PS -A MULTIOUTLET ASSEMBLY, REFER TO SPEC KI INTERCOM - DESK KI w INTERCOM - WALL 10 TELEPHONE - DESK II w TELEPHONE - WALL II H HOUSE PHONE I''A VOICE /DATA OUTLET 1 1 T_ TECHNOLOGY OUTLET (REFER TO SPE F BELL � FEY BUZZER I-n CHIME FE TELEVISION RECEIVER I- c M MICROPHONE OUTLET HD L LINE LEVEL OUTLET F c ' VOLUME CONTROL, ZONE 1 NUMBER INDICATED P El PROJECTOR OUTLET ES EFFECTS SPEAKER OUTLET i- REMOTE CONTROL Ms MONITOR SPEAKER OUTLET Hi, SR SOUND REINFORCEMENT OUTLET 1 QAT SPEAKER, CEILING MOUNTED WITH TYPE AND ZONE NUMBER INDICATED (REFER TO SPECIFICATION FOR TYPE) ®AT SPEAKER, WALL MOUNTED WITH TYPE AND ZONE NUMBER INDICATED (REFER TO SPECIFICATION FOR TYPE) Oil SPEAKER RE- ENTRANT HORN WITH ZONE NUMBER INDICATED .) CB 18" 54" 18" 54" 54" 18" 18" 80" 80" 80" 18" 18" 18" " 46" 18" 6" BFC HL 1. SURFACE FLUORESCENT, NORMAL POWER SURFACE FLUORESCENT, EMERGENCY POWER RECESSED FLUORESCENT, C _ . NO. CB NORMAL POWER =NV' RECESSED FLUORESCENT, EMERGENCY POWER WALL MOUNTED EXIT SIGN, SHADING 96" AFF INDICATES THE ILLUMINATED FACES or 8" BFC MOUNTED EXIT SIGN, SHADING INDICATES THE ILLUMINATED FACES BATTERY PACK, NORMAL POWER 96" AFF or 8" BFC 46.11- BATTERY PACK, EMERGENCY POWER 96" AFF or 8" BFC • POLE, BASE AND FIXTURE(S). CIRCLES •• • INDICATE # OF HEADS PER POLE, • NORMAL POWER POLE, BASE AND FIXTURE(S). CIRCLES INDICATE # OF HEADS PER POLE, EMERGENCY POWER FO WALL MOUNTED FIXTURE AND BRACKET, NORMAL POWER IAD WALL MOUNTED FIXTURE AND BRACKET, EMERGENCY POWER I 1 FOR TYPE AND RECEPTACLE SPACING al DISCONNECT SWITCH, NON -FUSED I ` f DISCONNECT SWITCH, FUSED MS MOTOR STARTER SWITCH WITHOUT OVERLOAD PROTECTION 54" Mss MOTOR STARTER SWITCH WITH 54" OVERLOAD PROTECTION 54 EF -1 MAGNETIC MOTOR STARTER WITH 'l EQUIPMENT NUMBER INDICATED EF -1 COMBINATION MOTOR STARTER AND FUSED DISCONNECT WITH EQUIPMENT NUMBER INDICATED I Q I STRIP FIXTURE, NORMAL POWER 1.0 STRIP FIXTURE, EMERGENCY POWER 0 SURFACE MOUNTED DOWNLIGHT,- NORMAL POWER . SURFACE MOUNTED DOWNLIGHT, EMERGENCY POWER 0 RECESSED DOWNLIGHT, NORMAL POWER 40 RECESSED DOWNLIGHT, EMERGENCY POWER -0 RECESSED WALL WASHER, NORMAL POWER -(O RECESSED WALL WASHER, EMERGENCY POWER V V TRACK FIXTURES AND TRACK HVAC AHU EQUIPMENT TAG (REFER TO EQUIPMENT SCHEDULE) 1 208 /120 VOLT PANELBOARD Pr A 480/277 VOLT PANELBOARD TERMINAL CABINET l FIRE ALARM DESCRIPTION MOUNTING ASSEMBLY, NORMAL POWER • V • TRACK FIXTURES AND TRACK F FIRE ALARM DEVICE, WHERE "X" CAN BE ONE OF THE FOLLOWING: (blank) FIRE ALARM MANUAL PULL STATION 46" K FIRE ALARM MANUAL KEYED STATION 46" I IONIZATION DETECTOR H THERMAL DETECTOR P PHOTOELECTRIC SMOKE DETECTOR DS DUCT SMOKE DETECTOR FL SPRINKLER VALVE FLOW SWITCH B -T BEAM DETECTOR, TRANSMITTER B -R BEAM DETECTOR, RECEIVER RB ROTATING BEACON MM MONITOR MODULE CM CONTROL MODULE D MAGNETIC DOOR HOLDER MR SHUTTER /ROLLING DOOR RELEASE TS DUCT DETECTOR REMOTE TEST STATION 80" VDT VIDEO DISPLAY TERMINAL Sc KEYBOARD PR SYSTEM EVENT PRINTER H F FIRE ALARM HORN 80" Q+� FIRE ALARM SPEAKER 80" FIRE ALARM STROBE 80" • H F FIRE ALARM HORN WITH STROBE 80" • MH F FIRE ALARM MINI -HORN WITH STROBE 80" • F 441 FIRE ALARM SPEAKER WITH STROBE 80" 141 F 46" FIREFIGHTER PHONE JACK 46 F FIRE ALARM BELL 80" FIRE ALARM CHIME 80" IF i FIRE ALARM CHIME WITH STROBE 80" QF -g SPRINKLER VALVE POSITION SWITCH ANNUNCIATOR PANEL ASSEMBLY, EMERGENCY POWER FEAX SWITCH, WHERE "X" CAN BE 46" ONE OF THE FOLLOWING: 2 = DOUBLE POLE 3 = THREE WAY 4 = FOUR WAY K = KEYED LV = LOW VOLTAGE MC = MOMENTARY WITH RTC OS = OCCUPANCY SENSOR (blank) = SINGLE POLE 600W �p DIMMER SWITCH, OPERATING 46" WATTAGE INDICATED 1409-' SWITCH WITH PILOT LIGHT 46" X X I a OCCUPANCY SENSOR, WHERE "Y" IS Y Y THE RATED AREA OF COVERAGE AND "X" IS ONE OF THE FOLLOWING: DT = DUAL TECHNOLOGY US = ULTRASONIC PIR = PASSIVE INFRARED MISCELLANEOUS DESCRIPTION MOUNTING - ® JUNCTION BOX, RECESSED WALL (j JUNCTION BOX, RECESSED CEILING 96 I-® CLOCK, WALL MOUNTED 8" I,BFG Q CLOCK, CEILING MOUNTED LINE VOLTAGE THERMOSTAT 58" FE PUSHBUTTON 46" EPO EMERGENCY POWER OFF PUSHBUTTON 46" litl Ts TIME SWITCH II CONTACTOR BRANCH CIRCUITING LP PANEL DESIGN PRESENTATION DESCRIPTION -1 -1 - NAME 1,3,5 CIRCUIT NUMBER(S) c 1 KEY NOTE, REFER TO LIST OF KEY NOTES V ON THE SAME PLAN 0 FEEDER NOTE, REFER TO FEEDER SCHEDULE ON THE SAME PLAN A DRAWING REVISION NOTE - GROUND CONDUCTOR NEUTRAL CONDUCTOR - -PHASE CONDUCTORS 3 /4" #6 CONDUIT AND WIRE SIZE (1/2" C, 2 #12, UNLESS NOTED OTHERWISE) LIGHT FIXTURE DESIGNATOR, REFER TO LIGHT A---- FIXTURE SCHEDULE FOR TYPE AND VOLTAGE /- --"\ CONCEALED RACEWAY , ` - ^ RACEWAY INSTALLED IN FLOOR OR BELOW FINISHED GRADE ME 1 / \ EXPOSED RACEWAY RACEWAY UP a CIRCUIT NUMBER SWITCH LEG RACEWAY DOWN 20/1 ELECTRICAL SHEET INDEX f SALES LTG - TRACK CONDUIT STUB, BUSHED AND CAPPED UNDERFLOOR DUCT, POWER AND EO TITLE SHEET & SCHEDULES El LIGHTING PLAN E2 POWER PLAN E3 SPECIFICATIONS -- COMMUNICATIONS RACEWAYS PANEL LA Location: Stockroom A.I.C. 10,000 208/120 Volt, 30, 4w Mounting: Surface Main: MCB 150A Circuit Description KVA CB NO. HL A B C HL NO. CB KVA Circuit Description SALES LTG - TRACK 1.8 20/1 1 1.0 X HVAC 11.1 0.9 2 20/1 0.4 SALES RECPT. - SHOW WINDOW SALES LTG - TRACK 1.8 20/1 3 40.4 X 50.1 4 20/1 0.6 SALES RECEPTACLES SALES LTG - TRACK 1.8 20/1 5 X 6 20/1 0.6 SALES RECEPTACLES SALES LTG - TRACK 1.5 20/1 7 X 8 20/1 0.2 SALES RECEPTACLES SALES LTG - TRACK 1.8 20/1 9 X * 10 20/1 0.4 CASH WRAP RECEPTACLES SALES LTG - TRACK 1.8 20/1 11 X 12 20/1 0.4 CASH WRAP RECEPTACLES SALES LTG - TRACK 1.8 20/1 13 X * 14 20/1 0.4 CASH WRAP RECEPTACLES SALES LTG - TRACK 1.8 20/1 15 X * 16 20/1 0.2 SECURITY SALES LTG - TRACK 1.2 20/1 17 X 18 20/1 0.2 TOILET GFI SALES LTG - TRACK 1.2 20/1 19 X 20 20/1 1.5 WATER HEATER SALES LTG - SHOW WINDOW 0.2 20/1 21 X 22 20/1 0.6 STOCKROOM RECEPTACLES SALES LTG - ENTRY 0.2 20/1 23 X 24 20/1 0.7 MANAGERS DESK SALES LTG - EMERGENCY 0.3 20/1 25 * X 26 20/1 0.7 MANAGERS DESK SALES LTG 0.4 20/1 27 X 28 20/1 0.2 PHONE BOARD DRESSING LTG 0.6 20/1 29 X * 30 20/1 SPARE STOCK ROOM LTG 0.8 20/1 31 * X 32 20/1 SPARE SIGN 0.8 20/1 33 X 34 20/1 SPARE SPARE 20/1 35 X 36 20/1 SPARE VAV -1 3.7 40/3 37 X 38 20/1 SPARE 3.7 39 X 40 20/1 SPARE 3.7 41 X 42 20/1 SPARE CONNECTED KVA: 38.0 CONNECTED AMPS: 119.2 A 14.3 B 12.5 C 11.2 DESIGN DEMAND KVA: 40.4 DESIGN DEMAND AMPS: 112.1 BALANCE PHASE LOADS TO WITHIN 10% OF EACH OTHER. ( *) INDICATES BREAKER TO BE LOCKED ON. LOAD SUMMARY CONNECTED KVA DESIGN FACTOR DESIGN DEMAND KVA LIGHTING 2.5 0.95 2.4 TRACK LIGHTING 16.5 1.0 16.5 RECEPTACLES 5.2 1.0 5.2 SIGN 0.8 1.0 0.8 WATER HEATER 3.6 1.0 3.6 HVAC 11.1 0.9 10.0 MISCELLANEOUS 1.9 1.0 1.9 TOTAL KVA: 41.6 40.4 TOTAL AMPS: 50.1 48.6 SERVICE KVA: 40.4 1.25 50.5 SERVICE AMPS: 60.7 Bait :vv��(�` CODE COMPLIANCE p re VED t=,, . 8 2008 City Of Tukvwi1 BU LDIN 1 ... }'G08- 7-0 9 DATE: 07/08/08 JOB NO: 08- 0196.004 DRAWN: MDR CHECKED: SOR 711 N. FIELDER RD. ARLINGTON, TX 76012 PH: (817) 635 -5696 FAX: (817) 635 -5699 0 po N. N rti 412.243.3430 • t Joe J co a� g4 440 Q :,.:�Q � wZZ� ., c� auu iljt) 00 1- M M HALL ENGINE Mechanical /Electrical Consulting Engineers 1750 Commerce Court, White Bear Lake, MN 55110 (651) 748-1100 • Fax (651) 748 -9370 REVISIONS 1. LANDLORD REVISIONS - 07/10/08 2. PLUMBING DIVISION REVISIONS - 08/05/08 TITLE SHEET AND SCHEDULES at ` SHEET NUMBER RECEIVED AUG 132OO1 PERMIT CENTER EO Dl F LA -31 EL LA-31 LA- -g90 L A4 OLA-3 EL LA -25 A2 OLA -3 A4 LA -11 FL (3) LA -29 0 00 0 ES LA- F LA -31 LIGHTING PLAN 1/4 " =1' -O" 25 A(4) LA -9 Q 8' 6 A(4) LA -9 O 8' EL LA-25 Ate^ LA-3 BO LA -27 BO LA -27 A2 O LA-3 8' O 4' A2 OLA-1 ,4' A(4) 8 A 22 LA -7 LA -7 4 A4 O ©A -1 A4 O LA-1 8' O EL LA -25 A LA-1 O 4' OF LA -23 ES LA -25 O F LA -2 LA -33j d� LA -33- A- J LA -33-A-® A14)i LA -7 A(4) % LA -5 0 ' A(4) / 8A(2) LA-5 LA-5 EL LA -25 6:1) 0 REFLECTED CEILING FIXTURE LEGEND SYMBOL TYPE MFR. PRODUCT N0. FINISH DESCRIPTION CAMPING MTG. METHOD MTG. HGT. VOLTS COMMENTS T# TRACK CON -TECH LT -4 -P, LT -8 -P, LT -12 -P WHITE SURFACE MTD. TRACK SURFACE 11 . -5 ,, 120 s LT = TRACK LENGTH, REFER TO ELECTRICAL DWGS. FOR TRACK LENGT ►• SURFACE MOUNTED; 1 CIRCUIT TRACK AME UX HITE RACK X !`IX ' -.. M• -,,- , 21 . kl M;.- " OLs' , ADJUS ' z E ACC , ■ LIGH ' ECTR• ' BALLA , 120V, \ • RROW ' BEAM DISTRIBUTOR, WHITE T XTURE FINISH Q A LT -20 -M - E -WT -C • - 120 -NF ACCENT CDM20 T /830 / % 11' -5" 120 1OD EMX 151 EEU -U -R -W WHITE EMER HEAD EMERGENCY LIGHT/ EXIT SIGN COMBO LED/ HALOGEN / LAMPS INCLUDED WALL SEE COMMENTS 120 DUAL HEAD EMERGENCY LIGHT EXIT SIGN COMBO - 90 MINUTE BATT RY POWER, WHITE, MOUNT 1" BELOW CEILING OR HIGHEST POINT ON WA L �* • NIIIIKIMIKL711111111r2 W RI. : ADJ .. E C C • VO. 2.• -0 , 0 •• „ ,I .: 0� •S __' • r. s: : N .9 -MM 14ILIGHT D AMERLUX ISI RA4- 39- T6- E -SD -C- 120 -CL EE -1 CLEAR WHITE RECESSED STOREFRONT Af CFNT DUAL MER HEAD EMERGENCY LIGHT CDM39/T6/830 LED/ HALOGEN LAMPS INCLUDED RECESSED WALL 9' -0" TIGHT TO CLG. 120 120 AMERLUX ROUND RECESSED ADJUSTABLE, 39W T6 METAL HALIDE DO LIGHT, SPOT, SEMI- DIFFUSE CLEAR TRIM DUAL HEAD EMERGENCY LIGHT - 90 MINUTE BATTERY POWER, WHITE N ��1 EL ES ISI PINK- R- SP- SW- UA -1 -W WHITE EXIT SIGN LED (INTEGRAL) SURFACE/ WALL SEE INTERIOR ELEVATION .. 120 151 PINNACLE EDGE -LIT EXIT SIGN SELF - POWERED 90 MINUTE BACKUP, CEILING RECESSED, UNIVERSAL ARROWS, 1 FACE, WHITE BACKGROUND F MERCURY MIE6-232-OCT-ELB-120V WHITE STRIP LIGHT (2)F32T8/730 PENDANT 11' -0" 120 MERCURY 4'-0",_ 2 LAMP 32W OCTRON T8 INDUSTRIAL FLUORESCENT WITH SYMMETRICAL REFLECTOR, ELECTRONIC BALLAST, 120V, WHITE 0 FL( #) FIXTURE BY REJUVENATION BULB BY FERROWATT FIXTURE: AA9479 - BRONZE W/ MAROON CORD (FL1 =36 "L - CORD, FL2 -30" CORD & FL3 =24" CORD); BULB: 1910N SQUIRRELCAGE FILAMENT BRONZE PENDANT FITTING ROOM LIGHT (1) 40 WATT BULB PER FIXTURE PENDANT VARIES, COORDINATE W/ CORD LENGTH 120 , REJUVENATION 'BURNSIDE' CLASSIC CLOTH - COVERED CORD PENDANT LIGHT FIXTURE BRONZE GILT CANOPY BASE, BRONZE SOCKET, MAR00 CORD, 40 WATT FERROWATT #1910N SQUIRRELCAGE FILAMENT BULB 0 F2 SPECTRUM SP4VF132E1 /441050 POLISHED CHROME RECESSED STOREFRONT ACCENT UFL- CF32 /TC /730 RECESSED 9' -0" 120 SPECTRUM L� " "TODIIAME TER, 32W COMPACT FLUORESCENT DOWNLIGHT, SOFT S M V -- __ -_ CUSTOM SALES AREA CHANDELIER (4) 60 WATT (MAX.) INCANDESCENT LAME PENDANT 9'-0" B'0' FIXTURE 120 CUSTOM SALES AREA CHANDELIER LIGHT FIXTURE SUPPLIED BY OWNER & INSTALLED BY G.C. SEE ELECTRICAL DRAWINGS FOR MORE INFORMATION SP -- -- BLACK SPEAKER SURFACE/ WALL TIGHT TO CLG. RECESSED CEILING MOUNTED SPEAKER SUPPLIED BY A/V VENDOR INSTALLED BY G.C. SEE ELECTRICAL DRAWINGS FOR MORE INFORMATION. GENERAL NOTES ELECTRICAL CONTRACTOR TO REFER TO ARCHITECTURAL DRAWINGS FOR ALL LIGHT FIXTURE LOCATIONS. A. CONTRACTOR SHALL COMPLETELY REMOVE ALL EQUIPMENT, PANELBOARDS, DEVICES, FIXTURES, WIRING, CONDUIT, ETC. AND ALL ASSOCIATED SUPPORTS, BRACING, PADS, ETC. NOT BEING REUSED OR SHOWN TO REMAIN WHETHER IN THE DEMISED SPACE, ON THE ROOF OR OTHERWISE LOCATED OUTSIDE OF THE DEMISED SPACE. DO NOT ABANDON IN PLACE. EY NOTES MAKE 120V CONNECTIONS TO STORE FRONT SIGN. VERIFY EXACT LOCATION. PROVIDE CONNECTION TO CEILING EXHAUST FAN /LIGHT COMBINATION. FAN AND LIGHT TO BE CONTROLLED BY COMMON SWITCH. aELECTRICAL SERVICE EQUIPMENT LOCATION. REFER TO SHEET E2, POWER RISER DIAGRAM AND PANELBOARD SCHEDULES. THE STOREFRONT CIRCUITS NOTED (LA -21, 23, &33) ARE TO BE CONTROLLED BY THE TIME CLOCK. COORDINATE EXACT SCHEDULING FORMAT WITH LANDLORD. SPEAKER AND WIRING PROVIDED BY TENANT'S VENDOR. ONLY IF REQUIRED BY MALL STANDARDS OR LOCAL CITY /BUILDING CODES, TENANT'S E.C. SHALL INSTALL 3/4" CONDUIT WITH PULLSTRING FROM EACH SPEAKER LOCATION TO A POINT DETERMINED BY AUDIO SUPPLIER AND BACK TO MANAGER'S DESK. COORDINATE EXACT SPEAKER TYPE, QUANTITIES AND LOCATIONS PRIOR TO ROUGH -IN. NOT USED. THIS LENGTH OF TRACK SHALL BE ON THE EMERGENCY /NIGHT LIGHTING CIRCUIT, LA -25. ".Lv L L:L) U CODE COMPLIANCE APPROVED L3 ]. 8 2E3 City Of Tukwila i It ING DIMON DATE: 07/08/08 08 -0196.004 106 NO: DRAWN: MDR CHECKED: SOR 711 N. FIELDER RD. ARLINGTON, TX 76012 PH: (817) 635 -5696 FAX: (817) 635 -5699 10 U LU H A L .{ 1. 16) Mechanical /Electrical alighting Engineers 1750 Commerce Court, White Bear Lake, MN 55110 (651) 748 -1100 • Fax (651) 748 -9370 REVISIONS 1. LANDLORD REVISIONS - 07/10/08 2. PLUMBING DIVISION REVISIONS - 08/05/08 PGo8 �� q e?d LIGHTING PLAN r '.I44 Vs ECEIVED AUG 13 2000 PERMIT CENTER SHEET NUMBER E1 F: LANDLORD GENERAL NOTES: LA -28 22 M• 75cd '042" • LA CI CM 0 N ■ 8 IIAP I 1PAP IC. 11Ap 6 IPA ti LA- `t GFI r 42- I ril 75cd POWER PLAN 114" = 1' -0" D NO BX, AC, OR ROMEX TYPE WIRING ALLOWED. NO ATTACHMENT OR SUPPORT FROM ANY ROOF DECK IS ALLOWED, HANGERS,CLAMPS AND SUPPORTS SHALL BE FASTEND TO BAR JOISTS OR BEAMS ONLY. ALL CABLING SHALL BE PLENUM RATED. ALL TENANT'S SERVED BY LANDLORDS AIR CONDITIONING UNITS HAVE PLENUM RETURNS. INSTALL A COMPLETE TYPE WRITTEN IDENTIFICATIONDIRECTORY CARD FOR ALL BRANCH CIRCUITS IN THE PANEL DOOR. " CONDUIT 1" CONDUIT MANAGER'S DESK BACK WRAP TELEPHONE BOARD LA� LA -22 �I 75cd• I* 0 -26 N ■ J L. H 110cd I 6 LA -4 LA -4 6120" A.F.F. LA -8 VAV -1 LA- 37,39,41 1 "C. -3 #8 IC. LA -10 '1.0 • T. T LA -10 1P !.' �. it fl NOTE: ELECTRICAL CONTRACTOR SHALL REUSE ANY EXISTING ELECTRICAL DISTRIBUTION EQUIPMENT IF IT COMPLIES WITH CODE AND IS OF SUFFICIENT CAPACITY. LEASE LINE LANDLORD ELEC. ROOM TENANT'S SPACE 1" CONDUIT TRENCHED OR CO 'E BORED TO CASH WRAP CABINE CASH WRAP TELEPHONE CONDUIT DIAGRA NTS C2 L 0 POWER RISER DIAGRAM NTS RISER DIAGRAM NOTES 0 EXISTING LANDLORD 277/480V, 3PH, 4W ELECTRICAL DISTRIBUTION. FIELD VERIFY PRIOR TO BID. 0 LANDLORD PROVIDED MASTER METERING EQUIP. IN LANDLORD'S ELECTRICAL ROOM. • LANDLORD TO PROVIDE FUSED DISC. SWITCH. COORDINATE EXACT REQUIREMENTS WITH LANDLORD PRIOR TO BID. • LANDLORD TO PROVIDE 1 1/4" C. 4 #3 CONDUIT FROM LANDLORD'S MAIN DISTRIBUTIONTO TENANT'S DEMISED PREMISES. COORDINATE EXACT REQUIREMENTS WITH LANDLORD PRIOR TO BID. MAIN FUSED DISCONNECT. NOT USED. • TENANT'S E.C. TO PROVIDE PANEL LA. REFER TO PANEL SCHEDULES ON SHEET EO. O PROVIDE 2 "C. 4#1/0 & 1#6 GND. 0 TENANT'S E.C. TO PROVIDE COPPER GROUND PER NEC, O TENANT'S E.C. TO PROVIDE NEW 45 KVA, 480V, 3PH, 3W - 208/120V, 3PH, 4W TRANSFORMER. 10 LANDLORD TO PROVIDE 480 VOLT, 30, 100A FUSED DISCONNECT SWITCH, FUSE AT 80 AMPS. 11 PROVIDE 1-1/4"C. 3 #4 & 1#8 GND. 12 TENANT'S ELEC. CONTRACTOR WILL PROVIDE A I.D. NAMEPLATE ON TENANT'S MAIN DISCONNECT SWITCH IN LANDLORD'S SWITCHBOARD. LA -4 LA -2 \c' LA -16 D LA -6 COR°VII.WWED FOR • DE COMPLIANCE- APPROVED p'it'y Of Tukwila )1 DING ..9rvrc ;ToN GENERAL NOTES A. CONTRACTOR SHALL COMPLETELY REMOVE ALL EQUIPMENT, PANELBOARDS, DEVICES, FIXTURES, WIRING, CONDUIT, ETC. AND ALL ASSOCIATED SUPPORTS, BRACING, PADS, ETC. NOT BEING REUSED OR SHOWN TO REMAIN WHETHER IN THE DEMISED SPACE, ON THE ROOF OR OTHERWISE LOCATED OUTSIDE OF THE DEMISED SPACE. DO NOT ABANDON IN PLACE. KEY NOTES 0, PROVIDE CONDUITS WITH PULL WIRE BACK TO MANAGER'S DESK IN STOCKROOM. 1" MINIMUM, BUSH CONDUIT'S ENDS. • TRENCH OR CORE BORE CONDUIT AND WIRE AS SHOWN. VERIFY ANY REQUIREMENTS WITH LANDLORD PRIOR TO BID. IF MORE THAN ONE (1) CONDUIT, CONDUIT SHALL BE IN COMMON TRENCH. %CONDUIT SHOWN SOLID TO BE SURFACE MOUNTED ON FLOOR IN SPACE BELOW CASEWORK FROM STUB -UP LOCATION TO CASH REGISTER DEVICE LOCATIONS. REFER TO KEY NOTE #2. • THE CIRCUITS USED TO POWER THE ELECTRONIC CASH REGISTERS SHALL NOT BE USED FOR ANY OTHER PURPOSES. THE CIRCUITS SHALL NOT SHARE THE NEUTRAL OR GROUND WITH OTHER EQUIPMENT. SEPARATE POWER, NEUTRAL AND INSULATED GROUND WIRES, MINIMUM SIZE #12 AWG, SHALL BE RUN TO THE CIRCUIT BREAKER PANELBOARD WHERE GROUND WIRE SHALL BE TIED TO THE GROUND TERMINAL ISOLATED FROM NEUTRAL. DO NOT USE THE CONDUIT FOR GROUNDING. ELECTRONIC CASH REGISTER OUTLETS SHALL BE HUBBELL NO. IG -5362, OR APPROVED EQUAL. ISOLATED GROUNDING CONDUCTOR SHALL TERMINATE WHERE THEY RECIVE THEIR SOURCE. INSTALLATION SHALL COMPLY WITH N.E.C. ARTICLE 250.146(D). 4 MAKE CONNECTION TO 120V, 1.5 KW WATER HEATER. MOUNT DISCONNECTING MEANS ADJACENT TO WATER HEATER. VERIFY EXACT LOCATION. • ELECTRICAL SERVICE EQUIPMENT LOCATION. INSTALLATION MUST COMPLY WITH N.E.0 ARTICLE 240.24(C) AND (D). • SERVICE DOOR BUZZER SYSTEM: EDWARDS: 340- 4G5 -24VAC BUZZER, ONE (1) BUZZER LOCATED AT BACK WRAP WALL AND ONE (1) BUZZER NEXT TO MANAGER'S DESK, 852 WEATHERPROOF PUSHBUTTON, 592 TRANSFORMER. BUZZER SYSTEM WIRE NEED NOT BE INSTALLED IN CONDUIT, UNLESS REQUIRED BY THE LANDLORD OR LOCAL AUTHORITY. REUSE EXISTING IF APPLICABLE. • LANDLORD WILL PROVIDE A COMMUNICATION CABLE TRAY LOCATED IN THE UTILITY CORRIDOR FOR THE TENANT'S USE.(NO CONDUIT WILL BE PROVIDED) LANDLORD WILL PROVIDE A COMMUNICATIONS TERMINAL BOARD WITHIN EACH LANDLORD ELECTRICAL ROOM. TENANT SHALL PROVIDE AND INSTALL A COMPLETE TELEPHONE SERVICE SUPPORT FACILITIES AS REQUIRED BY THE SERVICE TELEPHONE COMPANY. ALL TENANT TELEPHONE WILL BE CONTAINED WITHIN THE TENANT'S SPACE. ANY CORRIDOR PENATRATIONS WILL NEED TO BE FIRE CAULKED AS REQUIRED. • LANDLORD SHALL FURNISH AND INSTALL (ONE) FIRE ALARM J -BOX INSIDED THE DEMISED PREMISES FOR EACH TENANT'S USE CONNECTING THEIR INDIVIDUAL FIRE ALARM SYSTEMS OR COMPONENTS. TENANT SHALL FURNISH AND INSTALL IF NECESSARY INITIATION DEVICES, ANNUCIATION DEVICES AND CONTROLS AS REQUIRED BY LOCAL AUTHORITY HAVING JURISDICTION. TENANT SJALL CONTRACT WITH LANDLORD'S DESIGNED FIRE ALARM CONTRACTOR FOR DESIGN,PROGRAMMING AND FINAL CONNECTION TO LANDLORDS FIRE ALARM AT TENANT'S EXPENSE. TENANT SHALL ONLY USE LANDLORD'S DESIGNATED FIRE ALARM CONTRACTOR SPECIFIED EQUIPMENT TO ENSURE COMPATABILITY WITH LANDLORDS FIRE ALARM SYSTEM. A COPY OF ALL DRAWINGS SHALL BE ISSUED TO THE LOCAL FIRE MARSHALL. 10 PROVIDE J -BOX IN ACCESSIBLE CEILING SPACE FOR SECURITY SYSTEM. COORDINATE EXACT REQUIREMENTS WITH SECURITY SYSTEM SUPPLIER PRIOR TO BID. NO CORD AND PLUG CONNECTIONS ALLOWED ABOVE CEILING. 11 TIME CLOCK: PARAGON MODEL 7000- SERIES OR EQUAL WITH 7 DAY, 24 HOUR SCHEDULING FORMAT, MIN. (4) N.O. 20 AMP, 120/277 VOLT CONTACTS, 120 VOLT COIL AND SPRING WOUND RIDE THROUGH. SWITCH SHALL CONTROL STORE FRONT LIGHTING AND SIGN LIGHTING OR CONTACTOR(S) AS REQUIRED. 12 PROVIDE RECESSED FLUSH WHITE DUPLEX RECEPTACLE AT SHOW WINDOW CEILING. 13 NEW 208V/30 VAV BOX (VAV- 1)WITH ELECTRICAL HEAT BY MECHANICAL CONTRACTOR. PROVIDE 60A/3P/30 DISCONNECT SWITCH WITH (3) 40A FUSES. <>, PROVIDE CALL -FOR -AID BOX IN HANDICAPPED RESTROOM. DATE: JOB NO: DRAWN: MDR CFIECKED: SOR 07/08/08 08- 0196.004 711 N. FIELDER RD. ARLINGTON, TX 76012 PH: (817) 635 -5696 FAX: (817) 635 -5699 Project Coordination By: • '0 w LSI n N • 412.243.3430 C 0 00 00 00 o� HALL ENGINEE Mechanical/Electrical Consulting Engineers 1750 Commerce Court, White Bear Lake, MN 55110 (651) 748 -1100 . Fax (651) 748 -9370 REVISIONS 1. LANDLORD REVISIONS - 07/10/08 2. PLUMBING DIVISION REVISIONS - 08/05/08 T(208 -10i POWER PLAN RECEIVED AUG 13 2008 PERMIT CENTER SHEET NUMBER E2 16010 - GENERAL PROVISIONS A. WORK CONSISTS OF FURNISHING LABOR, MATERIALS, EQUIPMENT AND SERVICES REQUIRED FOR THE COMPLETE INSTALLATION OF ELECTRICAL WORK SHOWN IN THE CONTRACT DOCUMENTS AND SPECIFIED IN DIVISION 16. B. INCLUDE ALL PARTS AND LABOR, WHICH ARE INCIDENTAL AND NECESSARY FOR A COMPLETE AND OPERABLE INSTALLATION EVEN THOUGH NOT SPECIFICALLY MENTIONED IN THE CONTRACT DOCUMENTS. SUCH ITEMS INCLUDE NUTS, BOLTS, ANCHORS, BRACKETS, SLEEVES, OFFSETS IN CONDUIT, FITTINGS, RELAYS, ETC. C. ARRANGE WITH LANDLORD TO PROVIDE TEMPORARY AND PERMANENT UTILITY SERVICES AS REQUIRED AND COORDINATE THEIR INSTALLATION WITH CONSTRUCTION PROGRESS OF THIS PROJECT. PAY ALL FEES AND COSTS CHARGED BY UTILITY COMPANIES FOR UTILITY SERVICES. D. OBTAIN ALL TEMPORARY AND PERMANENT PERMITS AND LICENSES REQUIRED IN CONNECTION WITH THIS DIVISION'S WORK. PAY ALL FEES AND EXPENSES REQUIRED FOR SUCH PERMITS AND LICENSES. E. REQUEST INSPECTIONS AS REQUIRED BY REGULATING AGENCIES AND /OR REGULATIONS. PAY ALL CHARGES FOR INSPECTIONS BY REGULATING AGENCIES OF INSTALLATIONS OF PLANS AND SPECIFICATIONS. F. INCLUDE STATE AND LOCAL SALES TAXES IN THE BID. KEEP ACCURATE RECORDS OF THESE TAXES AND FURNISH SUCH RECORDS TO THE TENANT UPON REQUEST. G. MEET OR EXCEED ALL CURRENT APPLICABLE CODES, ORDINANCES AND REGULATIONS FOR ALL INSTALLATIONS. PROMPTLY NOTIFY THE ENGINEER, IN WRITING, IF THE CONTRACT DOCUMENTS APPEAR TO CONFLICT WITH GOVERNING CODES AND REGULATIONS. CONTRACTOR ASSUMES ALL RESPONSIBILITY AND COSTS FOR CORRECTING NON- COMPLYING WORK INSTALLED WITHOUT NOTIFYING THE ENGINEER. H. HIGHER QUALITY OF WORKMANSHIP AND MATERIALS INDICATED IN THE CONTRACT DOCUMENTS TAKES PRECEDENCE OVER THAT ALLOWED IN REFERENCED CODES AND STANDARDS. I. THE TERMS DEFINED BELOW APPLY TO ALL WORK INCLUDED IN DIVISION 16. 1. THE WORK - AS DEFINED IN THE 1997 AIA DOCUMENT A201: "THE TERM WORK' MEANS THE CONSTRUCTION AND SERVICES REQUIRED BY THE CONTRACT DOCUMENTS WHETHER COMPLETED OR PARTIALLY COMPLETED, AND INCLUDES ALL OTHER LABOR, MATERIALS, EQUIPMENT AND SERVICES PROVIDED OR TO BE PROVIDED BY THE CONTRACTOR TO FULFILL THE CONTRACTOR'S OBLIGATIONS. THE WORK MAY CONSTITUTE THE WHOLE OR A PART OF THE PROJECT." 2. FURNISH - TO OBTAIN IN NEW CONDITION READY FOR INSTALLATION INTO THE WORK. 3. INSTALL - TO STORE, SET IN PLACE, CONNECT AND PLACE INTO OPERATION INTO THE WORK. 4. PROVIDE - TO FURNISH AND INSTALL. 5. CONNECT - TO BRING SERVICE TO THE EQUIPMENT AND MAKE FINAL ATTACHMENT INCLUDING NECESSARY SWITCHES, OUTLETS, BOXES, TERMINATIONS, ETC. 6. CONDUIT - INCLUDES IN ADDITION TO CONDUIT, ALL FITTINGS, PULL BOXES, HANGERS AND OTHER SUPPORTS AND ACCESSORIES RELATED TO SUCH CONDUIT. 7. CONCEALED - HIDDEN FROM SIGHT IN CHASES, FURRED SPACES, SHAFTS, HUNG CEILINGS, EMBEDDED IN CONSTRUCTION, IN CRAWL SPACES OR BURIED. 8. EXPOSED: NOT INSTALLED UNDERGROUND NOR CONCEALED AS DEFINED ABOVE. J. THE DRAWING AND SPECIFICATIONS CONSTITUTE THE CONTRACT DOCUMENTS. ANY ITEM NOTED IN THE SPECIFICATION OR SHOWN ON THE DRAWINGS IS INCLUDED IN THE CONTRACT DOCUMENTS. K. ALL ELECTRICAL DETAILS AND DRAWINGS ARE DIAGRAMMATIC, UNLESS SPECIFICALLY NOTED. FIELD VERIFY ALL DIMENSIONS AND NOTIFY THE ENGINEER OF ANY CONFLICTS OR DISCREPANCIES, IN WRITING, PRIOR TO INSTALLATION. L. INITIATE, MAINTAIN AND SUPERVISE ALL SAFETY PRECAUTIONS REQUIRED W1TH THIS WORK IN ACCORDANCE WITH THE REGULATIONS OF THE OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA) AND OTHER GOVERNING AGENCIES. M. DO NOT REMOVE OR DISTURB ANY ASBESTOS CONTAINING MATERIALS FROM THE PROJECT. IMMEDIATELY STOP WORK AND NOTIFY THE TENANT IF ASBESTOS CONTAINING MATERIALS ARE SUSPECTED. N. BEFORE SUBMITTING A PROPOSAL ON THE WORK CONTEMPLATED, EXAMINE THE SITE OF THE PROPOSED WORK N A D BECOME THOROUGHLY FAMILIAR WITH EXISTING CONDITIONS AND LIMITATIONS. NO EXTRA COMPENSATION WILL BE ALLOWED BECAUSE OF MISUNDERSTANDING AS TO THE AMOUNT OF WORK INVOLVED NOR BIDDERS LACK OF NO K WLEDGE OF EXISTING CONDITIONS WHICH COULD HAVE BEEN DISCOVERED OR REASONABLY ANTICIPATED PRIOR TO BIDDING. 0. CON D N UITS _, PIPES, DUCTS, LIGHTS, DEVICES, SPEAKERS, ETC., SHOWN ON THE DRAWINGS AS EXISTING HAVE BEEN BASED ON EXISTING PLANS AND MAY NOT BE INSTALLED AS ORIGINALLY SHOWN. IT IS THE CONTRACTORS RESPONSIBILITY TO VISIT THE SITE AND MAKE EXACT DETERMINATION OF THE EXISTENCE, LOCATION AND CONDITION OF SUCH FACILITIES PRIOR TO SUBMITTING A BID. P. CONSULT THE DRAWINGS AND SPECIFICATIONS OF MECHANICAL AND OTHER TRADES FOR CORRELATING INFORMATION AND LAY OUT WORK SO THAT IT WILL COORDINATE WITH OTHER TRADES. VERIFY DIMENSIONS AND CONDITIONS (I.E., FINISHED CEILING HEIGHTS, FOOTING AND FOUNDATION ELEVATIONS, BEAM DEPTHS, ETC.) WITH THE ARCHITECTURAL AND STRUCTURAL DRAWINGS. NOTIFY THE ARCHITECT /ENGINEER OF ANY CONFLICTS THAT CANNOT BE RESOLVED, IN THE FIELD, BY AFFECTED TRADES. REPLACEMENT OF WORK DUE TO LACK OF COORDINATION AND FAILURE TO VERIFY EXISTING CONDITIONS WILL BE COMPLETED AT NO COST TO THE TENANT. Q. INSTALL ALL CONDUIT, CABLE TRAY, BUSDUCT, EQUIPMENT, ETC. ALLOWING PROPER CODE AND MAINTENANCE CLEARANCES AND TO AVOID BLOCKING PASSAGEWAYS AND ACCESS PANELS. R. WHERE WORK MUST BE REPLACED DUE TO THE FAILURE OF THE CONTRACTOR TO VERIFY THE CONDITIONS EXISTING ON THE JOB, SUCH REPLACEMENT MUST BE ACCOMPLISHED AT NO COST TO THE TENANT. THIS APPLIES TO SHOP FABRICATED WORK AS WELL AS TO WORK FABRICATED IN PLACE. S. THROUGHOUT THE COURSE OF THE WORK, MINOR CHANGES AND ADJUSTMENTS TO THE INSTALLATION MAY BE REQUESTED BY THE ENGINEER. THE CONTRACTOR SHALL MAKE ADJUSTMENTS WITHOUT ADDITIONAL COST TO THE TENANT, WHERE SUCH ADJUSTMENTS ARE NECESSARY TO THE PROPER INSTALLATION AND OPERATION WITHIN THE INTENT OF THE CONTRACT DOCUMENTS. THIS DOES NOT INCLUDE WORK ALREADY COMPLETED. T. OBTAIN EXACT LOCATION OF CONNECTION TO EQUIPMENT, FURNISHED BY OTHERS, FROM THE PERSON FURNISHING THE EQUIPMENT. U. DRAWINGS AND SPECIFICATIONS ARE COMPLEMENTARY AND WHAT IS CALLED FOR IN EITHER ONE IS AS BINDING AS IF CALLED FOR IN BOTH. V. INCLUDE THE BETTER QUALITY, GREATER QUANTITY OR HIGHER COST FOR AN ITEM OR ARRANGEMENT WHERE A DISAGREEMENT EXISTS IN THE DRAWINGS AND SPECIFICATIONS. W. GUARANTEE AND MAINTAIN THE STABILITY OF WORK AND MATERIALS AND KEEP SAME IN PERFECT REPAIR AND CONDITION FOR THE PERIOD OF ONE (1) YEAR AFTER THE FINAL COMPLETION OF THE WORK AS EVIDENCED BY ISSUANCE OF THE FINAL CERTIFICATE BY THE ARCHITECT. X. DEFECTS OF ANY KIND DUE TO FAULTY WORK OR MATERIALS APPEARING DURING THE ABOVE MENTIONED PERIOD MUST BE IMMEDIATELY MADE GOOD BY THE CONTRACTOR AT HIS OWN EXPENSE TO THE ENTIRE SATISFACTION OF THE TENANT AND ARCHITECT AND ENGINEER. INCLUDE DAMAGE TO THE FINISH OR THE BUILDING RESULTING FROM THE ORIGINAL DEFECT OR REPAIRS. Y. REPLACE ALL RECEPTACLES, SWITCHES, COVERPLATES, ETC., DAMAGED BY ANY CONTRACTOR DURING THE COURSE OF CONSTRUCTION. Z. MATERIALS FURNISHED FOR THE TEMPORARY LIGHT AND POWER SYSTEM REMAIN CONTRACTORS PROPERTY. REMOVE WHEN THERE IS NO LONGER ANY NEED FOR TEMPORARY LIGHT AND POWER OR WHEN DIRECTED BY THE ARCHITECT.. M. COORDINATE/SCHEDULE ALL WORK WITH THE TENANT TO MINIMIZE ANY DISRUPTIONS. CONFINE ALL INTERRUPTIONS TO THE SMALLEST POSSIBLE AREA. PROVIDE TEMPORARY CONNECTIONS IF REQUIRED TO PROVIDE CONTINUITY OF SERVICE. BB. INSPECT ALL AREAS AFFECTED BY THE INTERRUPTIONS AND RETURN ALL AUTOMATICALLY CONTROLLED EQUIPMENT, ELECTRICALLY OPERATED EQUIPMENT TO THE SAME OPERATING CONDITION PRIOR TO THE INTERRUPTION. CC. NO FIRE ALARM SYSTEMS ARE TO REMAIN INACTIVE AT THE END OF THE WORK DAY. ASSURE THAT THE FIRE ALARM SYSTEM IS OPERATIONAL AT THE END OF EACH WORK DAY. COORDINATE WITH THE LANDLORD. DD. DO NOT DISTURB NORMAL USE OF THE FACILITY, EXCEPT WITHIN THE IMMEDIATE CONSTRUCTION AREA. KEEP WALKS, DRIVEWAYS, ENTRANCES, ETC. FREE AND CLEAR OF EQUIPMENT, MATERIAL AND DEBRIS. EE STORE ALL EQUIPMENT AND MATERIAL IN A PLACE AND MANNER THAT MINIMIZES CONGESTION AND IS APPROVED BY THE TENANT. FF. PROVIDE NEW MATERIAL AND EQUIPMENT, UNLESS NOTED OTHERWISE. PROTECT EQUIPMENT AND MATERIAL FROM DAMAGE, DIRT AND THE WEATHER. GG, PROVIDE THE HIGHEST QUALITY WORKMANSHIP AND PERFORM ALL WORK ONLY BY SKILLED MECHANICS. INSTALL MATERIAL AND EQUIPMENT IN ACCORDANCE WITH MANUFACTURERS' RECOMMENDATIONS, INSTRUCTIONS AND CURRENT NECA STANDARDS. HH. THE TENANT RESERVES THE RIGHT TO REJECT MATERIAL OR WORKMANSHIP NOT IN ACCORDANCE WITH THE SPECIFICATIONS, BEFORE OR AFTER INSTALLATION. MM. PERFORM ALL CUTTING AND PATCHING NECESSARY TO WORK, UNLESS SPECIFICALLY DELEGATED TO THE GENERAL CONTRACTOR. OBTAIN SPECIAL PERMISSION FROM THE LANDLORD BEFORE CUTTING STRUCTURAL MEMBERS OR FINISHED MATERIAL. PERFORM ALL PATCHING IN SUCH A MANNER AS TO LEAVE NO VISIBLE TRACE AND RETURN THE AREA AFFECTED TO THE CONDITION OF UNDISTURBED WORK. PERFORM ALL PATCHING BY WORKERS EXPERIENCED, SKILLED, AND LICENSED FOR THE PARTICULAR TYPE OF WORK INVOLVED. INFERIOR WORK WILL NOT BE ACCEPTED. NN. PATCH ALL HOLES LEFT AS A RESULT OF DEMOLITION OF ELECTRICAL EQUIPMENT AND DEVICES. 00. PREVENT THE SPREAD OF DUST, DEBRIS, AND OTHER MATERIAL INTO ADJACENT AREAS. PP. REPLACE ALL CEILING TILES DAMAGED DURING INSTALLATION OF WORK, WITH NEW TILE. QQ. PROVIDE MINIMUM 4" HIGH CONCRETE PADS FOR ALL FLOOR MOUNTED EQUIPMENT. RR. SIZE PAD TO PROVIDE A MINIMUM 2" OVERLAP AROUND PERIMETER OF EQUIPMENT. SS. REFINISH ALL ELECTRICAL EQUIPMENT DAMAGED DURING SHIPPING AND /OR INSTALLATION TO ITS ORIGINAL CONDITION. REMOVE ALL RUST; PRIME, AND PAINT PER MANUFACTURER'S RECOMMENDATIONS FOR FINISH EQUAL TO ORIGINAL. TT. PAINT ALL NEW RACEWAY SYSTEMS IN EXPOSED FINISHED AREAS . UU. AFTER TESTS HAVE BEEN MADE AND ACCEPTED, CLEAN LIGHT FIXTURES, PANELS AND OTHER EQUIPMENT INSTALLED BY THE CONTRACTOR, LEAVING THE ENTIRE WORK AREA IN A CLEAN AND COMPLETE WORKING ORDER. W. OPERATE EQUIPMENT AND SYSTEMS IN ALL THEIR OPERATING MODES, TO VERIFY PROPER OPERATION, PRIOR TO FINAL INSPECTION AND OWNER INSTRUCTIONS. NOTIFY THE ENGINEER, IN WRITING, THAT ALL SYSTEMS HAVE BEEN TESTED AND ARE FUNCTIONING AND OPERATING PROPERLY WW. INCLUDE DOCUMENTATION OF INSTRUCTIONS IN THE OPERATION AND MAINTENANCE MANUALS. XX. CONTRACTOR IS RESPONSIBLE FOR ANY DAMAGE TO ELECTRICAL EQUIPMENT OR MATERIALS UNTIL FINAL ACCEPTANCE OF THE ENTIRE PROJECT BY THE TENANT. KEEP ALL EQUIPMENT CLEAN MATERIALS UNTIL FINAL ACCEPTANCE OF THE ENTIRE PROJECT BY THE TENANT. 16025 - DEMOLITION A. EXAMINE THE BUILDING TO DETERMINE ACTUAL CONDITIONS AND EXTENT OF WORK PRIOR TO BIDDING THE PROJECT. REFER ANY UNCLEAR DETAILS OR CONFLICTS TO THE ARCHITECT/ENGINEER FOR CLARIFICATION PRIOR TO BIDDING THE DRAWINGS. B. VERIFY THAT FIELD MEASUREMENTS AND CIRCUITING ARRANGEMENTS ARE AS SHOWN ON DRAWINGS. C. VERIFY THAT ABANDONED WIRING AND EQUIPMENT SERVE ONLY ABANDONED FACILITIES. D. BEGINNING OF DEMOLITION MEANS INSTALLER ACCEPTS EXISTING CONDITIONS. E. COORDINATE PHASING OF THE DEMOLITION WORK WITH THE CONSTRUCTION SEQUENCE SCHEDULE. F. DISCONNECT ELECTRICAL SYSTEMS IN WALLS, FLOORS, AND CEILINGS SCHEDULED FOR REMOVAL. G. COORDINATE UTILITY SERVICE OUTAGES WITH LANDLORD. H. IDENTIFY EXISTING ELECTRICAL EQUIPMENT SUCH AS CONDUITS, BOXES, PULLBOXES, CONDUIT BODIES, AND CONDUIT RACKS THAT WILL NEED ADDITIONAL SUPPORT DUE TO THE DEMOLITION OF THE EXISTING SUPPORTS. I. PROVIDE TEMPORARY WIRING AND CONNECTIONS TO MAINTAIN EXISTING SYSTEMS, INCLUDING TELEPHONE AND DATA SYSTEMS, IN SERVICE DURING CONSTRUCTION. WHEN WORK MUST BE PERFORMED ON ENERGIZED EQUIPMENT OR CIRCUITS, USE PERSONNEL EXPERIENCED IN SUCH OPERATIONS. J. EXISTING ELECTRICAL SERVICE: MAINTAIN EXISTING SYSTEM IN SERVICE UNTIL NEW SYSTEM IS COMPLETE AND READY FOR SERVICE. DISABLE SYSTEM ONLY TO MAKE SWITCHOVERS AND CONNECTIONS. NOTIFY AND OBTAIN PERMISSION FROM TENANT, ARCHITECT/ENGINEER AT LEAST 24 HOURS BEFORE PARTIALLY OR DISABLING SYSTEM. MINIMIZE OUTAGE DURATION. MAKE TEMPORARY CONNECTIONS TO MAINTAIN SERVICE IN AREAS ADJACENT TO WORK AREA K. EXISTING FIRE ALARM SYSTEM: MAINTAIN EXISTING SYSTEM IN SERVICE UNTIL NEW SYSTEM IS ACCEPTED. DISABLE SYSTEM ONLY TO MAKE SWITCHOVERS AND CONNECTIONS. NOTIFY AND OBTAIN PERMISSION FROM LANDLORD, ARCHITECT /ENGINEER AND LOCAL FIRE SERVICE AT LEAST 24 HOURS BEFORE PARTIALLY OR COMPLETELY DISABLING SYSTEM. MINIMIZE OUTAGE DURATION. MAKE TEMPORARY CONNECTIONS TO MAINTAIN SERVICE IN AREA ADJACENT TO WORK AREA L. EXISTING TELEPHONE/DATA SYSTEM: MAINTAIN EXISTING SYSTEMS IN SERVICE UNTIL NEW SYSTEMS ARE COMPLETE AND READY FOR SERVICE AND ACCEPTED. DISABLE SYSTEMS ONLY TO MAKE SWITCHOVERS AND CONNECTIONS. NOTIFY AND OBTAIN PERMISSION FROM LANDLORD, ARCHITECT /ENGINEER AND TELEPHONE UTILITY COMPANY AT LEAST 24 HOURS BEFORE PARTIALLY OR COMPLETELY DISABLING SYSTEM. MINIMIZE OUTAGE DURATION. MAKE TEMPORARY CONNECTIONS TO MAINTAIN SERVICE IN AREAS ADJACENT TO WORK AREA M. DEMOLISH AND EXTEND EXISTING ELECTRICAL WORK UNDER AND THIS SECTION, AND AS INDICATED ON THE DRAWINGS. REMOVE, RELOCATE, AND EXTEND EXISTING INSTALLATIONS TO ACCOMMODATE NEW CONSTRUCTION. N. PROVIDE SUPPORTS FOR ALL EXISTING ELECTRICAL EQUIPMENT THAT WAS SUPPORTED PREVIOUSLY BY DEMOLISHED WALLS, FLOORS, CEILING OR OTHER STRUCTURES. PROVIDE NEW SUPPORTS FROM STRUCTURAL MEMBERS NOT SLATED FOR DEMOLITION, PRIOR TO ANY DEMOLITION. 0. TENANT RESERVES THE RIGHT OF FIRST REFUSAL TO OBTAIN MATERIAL SHOWN TO BE REMOVED UNDER THIS CONTRACT. ITEMS NOT RETAINED BY THE TENANT BECOME H PROPERTY E PR PERTY OF THE CONTRACTOR AND MUST BE REMOVED FROM THE PREMISES. P. DEMOLISH AND REMOVE ALL ELECTRICAL SYSTEMS INDICATED FOR DEMOLITION. NO PORTION OF THESE SYSTEMS MAY BE ABANDONED IN PLACE. Q. REMOVE ABANDONED WIRING TO SOURCE OF SUPPLY. R. REMOVE EXPOSED ABANDONED CONDUIT, INCLUDING ABANDONED N NED CONDUIT ABOVE ACCESSIBLE CEILING FINISHES. CUT CONDUIT IN WALLS, FLOORS, OR COLUMNS BACK TO A POINT WHERE PATCHING CAN BE ADEQUATELY PERFORMED AND PATCH SURFACES. ES. S. DISCONNECT ABANDONED OUTLETS AND REMOVE DEVICES. REMOVE ABANDONED OUTLETS IF CONDUIT SERVICING THEM IS ABANDONED AND REMOVED. PROVIDE BLANK COVER FOR ABANDONED OUTLETS, WHICH ARE NOT REMOVED. T. DISCONNECT AND REMOVE ABANDONED PANELBOARDS AND DISTRIBUTION EQUIPMENT. U. DISCONNECT AND REMOVE ELECTRICAL DEVICES AND EQUIPMENT SERVING UTILIZATION EQUIPMENT THAT HAS BEEN REMOVED. V. DISCONNECT AND REMOVE ABANDONED LUMINARIES. REMOVE BRACKETS, STEMS, HANGERS, AND OTHER ACCESSORIES. W. REPAIR ADJACENT CONSTRUCTION AND FINISHES DAMAGED DURING DEMOLITION AND EXTENSION WORK. X. MAINTAIN ACCESS TO EXISTING ELECTRICAL INSTALLATIONS, WHICH REMAIN ACTIVE. MODIFY INSTALLATION OR PROVIDE ACCESS PANEL AS APPROPRIATE. Y. EXTEND EXISTING INSTALLATIONS USING MATERIALS AND METHODS COMPATIBLE WITH EXISTING ELECTRICAL INSTALLATIONS, OR AS SPECIFIED. RELOCATE AND REROUTE CONDUIT AND WRING AS REQUIRED FOR CONDUIT CONCEALED IN WALLS OR STRUCTURE BEING ALTERED AS PART OF THE REMODELING. MAINTAIN CONTINUITY TO ALL DEVICES IN AND DOWNSTREAM OF REMODELED WORK. Z. REROUTE EXISTING RACEWAY AND WRING, WHICH IS EXPOSED DUE TO REMOVAL OF EXISTING CONSTRUCTION. CONCEAL NEW RACEWAY AND WIRING AND MAINTAIN OPERATION. AA IF CONDUCTORS ARE REQUIRED TO BE REMOVED FROM EXISTING RACEWAYS, INSTALL WITH NEW CONDUCTORS. BB. PROVIDE NEW COVERPLATES THROUGHOUT THE REMODELED AREAS. CC. DISPOSE OF FLUORESCENT LAMPS, BALLASTS, AND OTHER HAZARDOUS MATERIALS IN ACCORDANCE WITH STATE AND FEDERAL REGULATIONS. DD. PRIOR TO REINSTALLATION OF USED EQUIPMENT, THOROUGHLY INSPECT EACH ITEM AND REPORT ANY DEFECTS TO THE ENGINEER/ARCHITECT IN WRITING. INSTRUCTIONS FOR CORRECTIVE MEASURES WILL BE GIVEN AT THE TIME AND THE CONTRACT AMOUNT ADJUSTED ACCORDINGLY. IF NO DEFECTS ARE REPORTED, THE MATERIAL WILL BE INCLUDED UNDER THE CONTRACTOR'S ONE - YEAR GUARANTEE AS OUTLINED IN SECTION 16010. EE. PANELBOARDS: CLEAN EXPOSED SURFACES AND CHECK TIGHTNESS OF ELECTRICAL CONNECTIONS. REPLACE DAMAGED CIRCUIT BREAKERS AND PROVIDE CLOSURE PLATES FOR VACANT POSITIONS. PROVIDE TYPED CIRCUIT DIRECTORY SHOWING REVISED CIRCUITING ARRANGEMENT. FF. LUMINARIES: REMOVE EXISTING LUMINARIES FOR CLEANING. USE MILD DETERGENT TO CLEAN ALL EXTERIOR AND INTERIOR SURFACES; RINSE WITH CLEAN WATER AND WIPE DRY. REPLACE LAMPS, BALLASTS, AND BROKEN ELECTRICAL PARTS. GG. INSTALL RELOCATED MATERIALS AND EQUIPMENT AS INDICATED ON THE DRAWINGS. 16050 -. BASIC MATERIALS AND METHODS A ENCASE ALL CONDUCTORS IN A CONTINUOUS RACEWAY SYSTEM. PROVIDE PULL AND JUNCTION BOXES AS REQUIRED BY THE NEC. SIZE ALL RACEWAY PER THE NEC WITH OVERSIZE CONDUITS AS INDICATED. PROVIDE MINIMUM 3/4" CONDUIT FOR BRANCH CIRCUIT HOMERUNS, PROVIDE MINIMUM 1/2" CONDUIT, UNLESS, NOTED OTHERWISE. B. PROVIDE EMT FOR ALL CONDUCTORS UNLESS NOTED OTHERW SE. PROVIDE CONCRETE -TIGHT STEEL COMPRESSION OR STEEL SETSCREW TYPE FITTINGS, COUPLINGS AND BUSHINGS. CAST OR INDENTOR TYPE DEVICES ARE NOT ACCEPTABLE. ALL FITTINGS USED IN PLENUM APPLICATIONS SHALL BE RATED FOR SUCH USE C. PROVIDE IMC OR CONCRETE- ENCASED PVC CONDUIT FOR SERVICE ENTRANCE CONDUCTORS. D. PVC CONDUIT MAY BE USED UNDERGROUND OR BELOW CONCRETE SLABS. PROVIDE COATED RIGID STEEL ELBOWS FOR ALL ELBOWS WHERE PVC IS USED. E. PROVIDE FLEXIBLE METAL CONDUIT FOR CONNECTIONS TO TRANSFORMERS, MOTORS AND OTHER VIBRATING PIECES OF EQUIPMENT. PROVIDE CONDUI T FOR ALL CONNECTIONS IN DAMP OR WET LOCATIONS. PROVIDE GROUND TYPE FITTINGS AND GROUNDING CONDUCTOR INSIDE ALL FLEXIBLE CONDUIT. ADJUST CONDUIT SIZE IF REQUIRED. F. PROVIDE RECESSED OUTLET BOXES AND JUNCTION BOXES IN ALL NEW CONSTRUCTION. CONCEAL ALL CONDUIT WORK IN NEW CONSTRUCTION, EXCEPT MECHANICAL ROOMS. CONDUIT AND BOXES IN MECHANICAL ROOMS MAY BE RUN EXPOSED. G. PROVIDE EXPANSION FITTINGS WHERE RACEWAY CROSSES BUILDING EXPANSION JOINTS. H. RUN ALL EXPOSED CONDUIT IN A NEAT, WORKMANLIKE MANNER PARALLEL TO THE BUILDING LINES, TIGHT TO THE WALL AND CEILING SURFACES, AND FIRMLY SUPPORT WITH CONDUIT CLAMPS OR HANGERS. PROVIDE TWO (2) HOLE MOUNTING STRAPS, MINIMUM THREE (3) FEET ON CENTER, FOR ALL SURFACE CONDUIT MOUNTED ON WALLS LESS THAN SIX (6) FEET ABOVE FINISHED FLOOR. PLACE CONDUITS AT LEAST 8" AWAY FROM ALL HOT PIPING AND SURFACES INCLUDING DOMESTIC HOT WATER LINES. I. PROVIDE GALVANIZED CODE GAUGE STEEL JUNCTION AND PULL BOXES WITH SCREW ON COVERS OF TYPE, SHAPE AND SIZE REQUIRED TO SUIT EACH INSTALLATION. PROVIDE GASKETING IN DAMP AND DUSTY LOCATIONS. PROVIDE CAST BOXES IN WEATHERPROOF, VAPOR TIGHT AND EXPLOSION PROOF ENVIRONMENTS. J. PROVIDE 4" BOXES THROUGHOUT. PROVIDE 3 1/2" DEEP BOXES WHERE INSTALLED IN MASONRY, 2 1/2" MINIMUM ELSEWHERE. PROVIDE SINGLE GANG MUD OR TILE RING FOR SINGLE DEVICES. K. MOUNT OUTLETS BOXES IN EXPOSED MASONRY WALLS WITH THE BOTTOM OF THE BOX ON THE TOP OF THE MORTAR JOINT AND THE VERTICAL LINE OF THE BOX EITHER ON THE MORTAR JOINT OR ON THE CENTER LINE OF THE MASONRY UNIT. PLUMB AND ACCURATELY ALIGN ALL WALL OUTLETS IN ROWS. MOUNT CEILING BOXES SYMMETRICAL WITH WALLS, BEAMS AND /OR TILES. MOUNTING HEIGHTS INDICATED ON THE DRAWINGS ARE FROM THE CENTER OF THE OUTLET BOX TO THE FINISHED FLOOR DIRECTLY BELOW THE OUTLET. EXTERIOR HEIGHTS ARE FROM INSIDE ADJACENT DOOR, OR IF NO DOOR, FROM THE FIRST FLOOR ABOVE GRADE, UNLESS NOTED OTHERWISE. L. COORDINATE THE LOCATION OF ALL OUTLETS WITH ARCHITECTURAL AND MECHANICAL DRAWINGS BEFORE INSTALLATION. COORDINATE ALL DOOR SWINGS IN THE FIELD BEFORE LOCATING SWITCHES. Mfr. Cooper Hubbell P &S Leviton 1-pole 2221 HBL1221 PS2OAC1 1221 -2 1 -pole w/Pilot 2221PL HBL1221PL PS2OAC1- RPL 1221 -2PL 2 -pole 2222 HBL1222 PS2OAC2 1222 -2 3 -way 2223 HBL1223 PS2OAC3 1223 -2 4 -way 2224 HBL1224 PS2OAC4 1224 -2 Keyed I -pole 2221L HBL1221L PS2OAC1- L 1221 -2L Mom. Contact 1995 HBL1557 1251 1257 M. PROVIDE NEW WIRING DEVICES IN EACH OUTLET INDICATED ON THE DRAWINGS. PROVIDE ALL DEVICES FROM ONE MANUFACTURER. COLOR TO MATCH ADJACENT SURFACE. N. APPROVED TOGGLE SWITCH MANUFACTURERS/MODEL NUMBERS: 0. APPROVED STANDARD RECEPTACLE MANUFACTURERS/MODEL NUMBERS: Manufacturer Cooper Hubbell P &S Leviton Simplex 5361 HBL5361 5361 5361 Duplex 5362 HBL5362 5362A or PT5362A 5362 XGF20 GFR5352A 2094 8899 IG5362 105362 IG6300 5362- IG 53625 HBL5360SA 8300SP 7380 Tamper Resistant TR8300 HBL8300SGA TR63H 8300 -SG "PROVIDE THE CORRESPONDING HOSPITAL GRADE DEVICE WHEN THIS DEVICE IS USED. P. PROVIDE NEW COVERPLATES OVER ALL BOXES WITH THE FOLLOWING SPECIFICATIONS: ALL FINISHED AREAS AND UNFINISHED AREAS PROVIDE SMOOTH PLASTIC COVERS, COLOR TO MATCH ADJACENT SURFACE OR AS SELECTED BY THE ARCHITECT. PROVIDE APPROPRIATE COVERS OVER SPECIAL PURPOSE RECEPTACLES. PROVIDE NEW WEATHERPROOF COVERPLATES FOR OUTLETS AND SWITCHES AS INDICATED ON THE DRAWINGS AND FOR ALL EXTERIOR DEVICES. Q. PROVIDE WIRE AND CABLE WITH INSULATION VOLTAGE RATING EQUAL TO OR GREATER THAN THE APPLIED SYSTEM VOLTAGE. PROVIDE SOLID OR STRANDED COPPER CONDUCTORS WITH TYPE THWN, TFIHN, OR XHHN INSULATION FOR NO. 12 AWG AND NO. 10 AWG CONDUCTORS. PROVIDE STRANDED COPPER CONDUCTORS WITH TYPE THWN, THHN, OR XHHW INSULATION FOR NO.8 AWG AND LARGER CONDUCTORS. PROVIDE MINIMUM NO. 12 AWG CONDUCTOR SIZE, UNLESS NOTED OTHERWISE. USE THE MINIMUM CONDUCTOR SIZE WHEN NO SIZE IS INDICATED. ALL CONDUCTORS TO BE COLOR - CODED AS FOLLOWS;120/208 VOLT SYSTEMS -PHASE A(BLACK), PHASE B(RED), PHASE C(BLUE), NEUTRAL WHITE . 277/480 VOLT SYSTEMS -PHASE A BROWN PHASE B ORANGE PHASE C YELLO ( ) 1 ), B( ORANGE) ( 1M, NEUTRAL(WHITE WITH TRACER OR GRAY). GROUNDING SYSTEM(GREEN). R. PRIOR TO TURNING THE BUILDING OVER TO THE OWNER TURN ON ALL EQUIPMENT IN THE BUILDING INCLUDING LIGHTING AND WITH A MULTIMETER, READ THE CURRENT DRAWN ON EACH HOT LEG OF FEEDER SUPPLYING EACH DISTRIBUTION PANEL. IF THE CURRENT IN ANY ONE LEG VARIES MORE THAN 5% (PLUS OR MINUS) FROM THE ARITHMETIC AVERAGE OF THE CURRENT IN ALL THE HOT LEGS, RECONNECT THE BRANCH CIRCUITS TO OBTAIN A BALANCED LOADING. S. PROVIDE FIRE BARRIERS AROUND CONDUIT, PIPE, TUBING, BUS DUCTS AND CABLES PASSING THROUGH SMOKE AND FIRE RATED FLOORS AND WALLS. PROVIDE CP 25, 303 AND PSS7904 SERIES BY 3M, OR "FLAME- SAFE" SYSTEM BY THOMAS AND BETTS CORP FOR FIRE SEALS. T. MAKE CONNECTIONS TO ALL MOTORS AND EQUIPMENT FURNISHED AND SET IN PLACE BY OTHERS. PROVIDE STARTERS, MANUAL CONTROLS AND AUXILIARY EQUIPMENT WHERE INDICATED IN SCHEDULES AND SPECIFIED HEREIN. PROVIDE ALL DISCONNECT SWITCHES AS INDICATED IN SCHEDULES, SPECIFIED HEREIN AND REQUIRED BY CODE.. 16400 - POWER DISTRIBUTION A. RETAIL METERING CENTER 1. PROVIDE METER SECTIONS CONTAINING METER QUANTITIES AS INDICATED ON THE DRAWINGS. 2. PROVIDE METER BRANCHES RATED 200 AMP MAXIMUM. 3. PROVIDE 3 PHASE, 4 WIRE METERS FOR USE ON 120/208 VOLT AND 277 /430 VOLT, 3 PHASE, 4 WIRE SYSTEMS WITH SEVEN (7) JAW METER SOCKETS. METERS FURNISHED BY THE UTILITY COMPANY. 4. MOUNT ALL OF THE ABOVE COMPONENTS AS SHOWN ON THE DRAWINGS IN A UL APPROVED AND LABELED, NEMA CLASS 1 FLOOR MOUNTED STEEL ENCLOSURE. ENCLOSURE TO BE CONSTRUCTED TO FINISHED STEEL CLEANED, PRIMED, AND PAINTED WITH BAKED ENAMEL FINISH PRIOR TO SHIPMENT TO THE JOB SITE. B. PROVIDE FUSES OF THE FOLLOWING TYPES (BUSSMAN USED AS REFERENCE): 1. 600 AMPS AND ABOVE: TIME -DELAY TYPE DESIGNED TO HOLD 500% OF RATED CURRENT FOR A MINIMUM OF 4 SECONDS AND CLEAR 20 TIMES CURRENT IN 0.01 SECONDS OR LESS WITH INTERRUPTING RATINGS OF 200,000 AMPERES RMS SYMMETRICAL AND PEAK LET - THROUGH CURRENT AND ENERGY LET - THROUGH VALUES ESTABLISHED BY U.L. STANDARD FOR CLASS L FUSES. PROVIDE KRP-C FUSES. 2. BELOW 600 AMPS: DUAL - ELEMENT CONSTRUCTION WITH INTERRUPTING RATING OF 200,000 AMPERES RMS SYMMETRICAL AND PEAK LET -THRU CURRENT ESTABLISHED BY U.L. STANDARD FOR CLASS RK -1 FUSES. PROVIDE LPN- RK/LPS -RK. 3. MOTOR CIRCUITS: PROTECT ALL INDIVIDUAL MOTOR CIRCUITS WITH FULL LOAD AMPERE RATING (FLA) OF 480 AMPERES OR LESS WITH DUAL - ELEMENT TIME -DELAY FUSES. PROVIDE LPN - RK/LPS -RK. PROTECT LARGER HORSEPOWER MOTORS WITH TIME -DELAY FUSES. PROVIDE KRP -C FUSES. PROVIDE U.L. CLASS RK1, DUAL - ELEMENT TIME -DELAY FOR ALL OTHER MOTORS,. 4. MOTOR CONTROLLERS: PROTECT NEMA AND IEC STYLE MOTOR CONTROLLERS WITH DUAL - ELEMENT, TIME -DELAY FUSES TO PROVIDE TYPE 2 COORDINATION FOR THE CONTROLLER. PROVIDE LPS -RK FUSES. 5. PROTECT CIRCUIT BREAKER PANELS WITH U.L. CLASS RK1, CLASS L FUSES. PROVIDE LPN -RK, LPS -RK, OR KRP -C FUSES. 6. PROVIDE FUSE SIZES AS INDICATED ON THE DRAWINGS. 7. ACCEPTABLE MANUFACTURERS: HUSSMAN, FERRAZ- SHAWMUT OR LITTELFUSE OR PRE - APPROVED EQUAL. C. PROVIDE LIGHTING AND APPLIANCE PANELBOARD ASSEMBLIES ADHERING TO THE FOLLOWING SPECIFICATIONS: 1. ENCLOSURES CONSTRUCTED OF GALVANIZED SHEET STEEL OF THICKNESS AS REQUIRED BY CODE, WITH ENAMELED STEEL TRIM, DISTRIBUTED BUSING, HINGED STEEL DOORS LATCHES, LOCKS AND ADJUSTABLE TRIM CLAMPS. PROVIDE NEMA 3R ENCLOSURES FOR EXTERIOR LOCATIONS. 2. PROVIDE WELDED METAL FRAME WITH TYPED CIRCUIT DIRECTORY FOR EACH PANEL. 3. COMPLIANT TO THE FOLLOWING STANDARDS: UL 50, UL 67, NEMA PB-1, NFPA 70 AND FED. SPEC W- P -115C , UL 489, NEMAAB -1, FED. SPEC. W- C- 375B /GEN, IEC 157 -1 AND BS 4752. 4. COMPLIANT TO ARTICLE 384 OF THE NEC: "LIGHTING AND APPLIANCE PANELBOARD". MAXIMUM OF 42 POLES PER PANELBOARD ASSEMBLY. 5. PROVIDE PANELBOARDS WITH INTERRUPTING RATINGS AS SHOWN ON THE PLANS. 6. PROVIDE 240 VOLT AC RATED PANELBOARDS FOR 208/120 AND 240 VOLT AC SYSTEMS. PROVIDE 480/277 VOLT RATED PANELBOARDS FOR 480/277 VOLT SYSTEMS. 7. PROVIDE TIN - PLATED COPPER BUS BARS OR TIN - PLATED ALUMINUM BUS BARS. 8. PROVIDE PROPER LUGS (75° C. MINIMUM TEMPERATURE RATING) AND GUTTER SPACE FOR CABLE SIZE INDICATED ON THE PLANS. 9. PROVIDE ALL PANELS BY THE SAME MANUFACTURER 10. PROVIDE SCREW MOUNTED, ENGRAVED NAMPLATES FOR EACH PANELBOARD. 11. PROVIDE MOLDED CASE, NON- ADJUSTABLE, THERMAL - MAGNETIC, QUICK -MAKE, QUICK - BREAK, BOLT -ON TYPE CIRCUIT BREAKERS. REFER TO THE SCHEDULES ON THE PLANS FOR SIZES AND QUANTITIES. 12. PROVIDE MULI -POLE BREAKERS WHERE INDICATED ON THE SCHEDULES HANDLE TIES ON SINGLE POLE BREAKERS ARE NOT ACCEPTABLE. 13. SERIES RATING OF CIRCUIT BREAKERS IS NOT ALLOWED. 14. ACCEPTABLE MANUFACTURERS: A. 240 VOLT 1.SQUARE D TYPE NQOD OF NF 2.SIEMENS TYPE S1 SERIES 3.CUTLER HAMMER POW -R -LINE 1A SERIES 4.GENERAL ELECTRIC AQ SERIES 5.PRE- APPROVED EQUAL B. 480 VOLT 1.SQUARED D TYPE NF 2.SIEMENS TYPE S2 SERIES 3.CUTLER HAMMER POW -R -LINE 2A SERIES 4.GENERAL ELECTRIC AE SERIES 5.PRE- APPROVED EQUAL D. PROVIDE PANEL IDENTIFICATION LABEL FOR EACH PANEL INCLUDING PANEL NAME, VOLTAGE AND FEEDER. FOR EXAMPLE: "HDP -1 -1, 480/277 V, 30, 4 WIRE, 2 "C - 4# 4/0 THWN ". E. MOUNT PANELBOARDS AND CABINETS TO BUILDING STRUCTURE OR INTERIOR WALL CONSTRUCTION. MOUNT INDEPENDENT OF CONDUIT AND RACEWAYS ENTERING BOXES. F. MOUNT PANELBOARDS WITH CABINET TOP AT 78" ABOVE FINISHED FLOOR. G. PROVIDE 3/4 "EMPTY CONDUITS FROM EACH FLUSH MOUNTED PANELBOARD. WHEN THE FLOOR IS ON GRADE, PROVIDE THREE (3) CONDUITS INTO THE CEILING CAVITY ABOVE. WHEN THE FLOOR HAS ACCESSIBLE SPACE BELOW, PROVIDE TWO (2) CONDUITS INTO THE CEILING SPACE ABOVE AND TWO (2) CONDUITS INTO THE ACCESSIBLE SPACE BELOW THE FLOOR ENDS SHALL BE CAPPED AND SHALL BE TAGGED AT BOTH ENDS WITH PERMANENT TAGS. H. PROVIDE A CIRCUIT DIRECTORY COMPLETELY TYPED ON THE INTERIOR OF EACH PANEL DOOR I. EQUIPMENT GROUND - SOLIDLY GROUND ALL CONDUIT SYSTEMS, SWITCH BOXES, CABINETS, MOTOR FRAMES, SWITCHGEAR, TRANSFORMERS, AND ALL OTHER PERMANENTLY INSTALLED EQUIPMENT IN ACCORDANCE WITH THE LATEST EDITION OF THE NATIONAL ELECTRICAL CODE TO FORM A CONTINUOUS, PERMANENT AND EFFECTIVE GROUNDING SYSTEM. BOND EXPANSION JOINTS AND METAL RACEWAY SECTIONS. PROVIDE GROUND CONDUCTOR AS INDICATED ON THE DRAWINGS OR SPECIFIED HEREIN. J. WHEN CONNECTING SINGLE PHASE CIRCUITS AND EQUIPMENT TO A THREE (3) PHASE SYSTEM, DISTRIBUTE THE LOADS ON THE PHASES TO ACHIEVE AN APPROXIMATELY BALANCED LOADING OF THE THREE -PHASE SYSTEM. 16430 - MOTOR CONTROL A PROVIDE "ON -OFF' TOGGLE TYPE MANUAL STARTER SWITCH WITH THERMAL OVERLOAD PROTECTION FOR SINGLE PHASE MOTORS, WHERE MANUAL CONTROL IS INDICATED. PROVIDE EACH SWITCH WITH A RED PILOT LIGHT INDICATING WHEN MOTOR IS ON. B. PROVIDE FULL VOLTAGE TYPE STARTERS AND THERMAL OVERLOAD PROTECTION AND EXTERNAL MANUAL RESET FOR ALL THREE -PHASE MOTORS, UNLESS INDICATED OTHERWISE. EQUIP EACH STARTER WITH 120 VOLT COIL, CONTROL POWER TRANSFORMER, SECONDARY FUSE BLOCK AND FUSES, AUXILIARY CONTACTS AS INDICATED, RED "ON" PILOT LIGHT, AND "HAND -OFF- AUTO" CONTROL SWITCH. PROVIDE COMBINATION STARTER/DISCONNECT WHEN INDICATED ON THE PLANS. ACCEPTABLE MANUFACTURERS FOR MAGNETIC STARTERS: ALLEN- BRADLEY BULL. 509 &512, SQUARE D CLASS 8536, CUTLER HAMMER, GENERAL ELECTRIC, ITE/SIEMENS EQUIVALENT OR PRE- APPROVED EQUAL. C. PROVIDE MANUAL MOTOR STARTING SWITCH OR TYPE "SS" FUSED DISCONNECT ADJACENT TO EACH 120 VAC SINGLE PHASE MOTOR LOCATED OUT OF SIGHT AND /OR IN EXCESS OF 50' -0" FROM THE CONTROLLER, OR AS INDICATED ON THE DRAWINGS.. D. INTER LOCK ROOFTOP HVAC UNIT FAN STARTER WITH DUCT DETECTOR TO SHUT DOWN FAN UPON DETECTOR ACTIVATION. 16460 - TRANSFORMERS A PROVIDE VENTILATED, INDOOR, DRY -TYPE DISTRIBUTION TRANSFORMER WITH THE CAPACITY AND VOLTAGE CHARACTERISTICS INDICATED ON THE DRAWINGS. TRANSFORMERS 15 KVA AND ABOVE WILL BE DESIGNED TO OPERATE WITH A 115 DEGREES C. TEMPERATURE RISE ABOVE 40 DEGREES C. AMBIENT. PROVIDE ALL INSULATING MATERIALS FOR A 220 DEGREES C. INSULATION SYSTEM. B. PROVIDE TRANSFORMERS MEETING OR EXCEEDING NEMA CLASS 1 EFFICIENCY REQUIREMENTS AS REQUIRED IN THE LOCAL ENERGY CODE. C. PROVIDE VOLTAGE TAPS AS INDICATED BELOW: 1. PROVIDE TWO 5% FCBN TAPS FOR ALL SINGLE AND 3 PHASE TRANSFORMERS 9 KVA AND BELOW. 0 1/2% 2. PROVIDE TWO 2 1/2 /o FCBN AND TWO 2 1C1 /o FCAN TAPS FOR ALL 3 PHASE TRANSFORMERS 15 KVA AND BELOW. 3. PROVIDE FOUR 2 1/2% FCBN AND TWO 2 1/2% FCAN TAPS FOR ALL 3 PHASE TRANSFORMERS ABOVE 15 KVA D. PROVIDE SOUND RATINGS NOT EXCEEDING THE FOLLOWING LEVELS: 1. 0 TO 15 KVA, 40 DECIBELS. 2. 15 TO 50 KVA, 45 DECIBELS. 3. 50 TO 150 KVA, 50 DECIBELS. 4. 150 KVA OR GREATER 50 DECIBELS. E. PROVIDE CONTINUOUS COPPER OR ALUMINUM COIL CONDUCTORS WITH BRAZED OR WELDED TERMINATIONS. F. ISOLATE TRANSFORMER CORE AND COIL FROM THE ENCLOSURE USING VIBRATION - ABSORBING MOUNTS. G. PROVIDE TRANSFORMERS 75 KVA OR LESS WITH ENCLOSURES SUITABLE FOR WALL, FLOOR OR TRAPEZE MOUNTING. PROVIDE TRANSFORMER LARGER THAN 75 KVA WITH ENCLOSURES SUITABLE FOR FLOOR OR TRAPEZE MOUNTING. H. PROVIDE MAXIMUM CASE TEMPERATURES NOT EXCEEDING A 35C TEMPERATURE RISE ABOVE A 40 DEGREE C AMBIENT. I. ACCEPTABLE MANUFACTURERS: CUTLER HAMMER, GENERAL ELECTRIC, SORGEL, HEVI -DUTY JEFFERSON ELECTRIC OR PRE - APPROVED EQUAL. 16500 - LIGHTING A COMPLY WITH NEC AS APPLICABLE TO THE INSTALLATION AND CONSTRUCTION OF LIGHT FIXTURES. B. COMPLY WITH UBC AS APPLICABLE TO THE INSTALLATION AND CONSTRUCTION OF LIGHT FIXTURES. C. PROVIDE LIGHT FIXTURES THAT ARE LISTED AND LABELED BY U.L. OR ANOTHER NATIONALLY RECOGNIZED TESTING LABORATORY FOR THE APPLICATION. D. PROVIDE LAMP BALLASTS THAT COMPLY WITH CERTIFIED BALLAST MANUFACTURERS ASSOCIATION STANDARDS AND CARRY THE CBM LABEL. E. COMPLY WITH ALL LOCAL, STATE AND FEDERAL ENERGY CODES. F. PROVIDE FIXTURES WITH LAMPS, FOR EACH OUTLET SHOWN ON THE DRAWINGS AND AS SPECIFIED HEREIN. SEE FIXTURES LIST ON THE PLAN. G. PROVIDE FLUORESCENT LAMP BALLASTS WITH THE FOLLOWING MINIMUM SPECIFICATIONS 1. DISCONNECTING MEANS ON THE LINE SIDE OF THE BALLAST TO DISCONNECT ALL HOT AND NEUTRAL CONDUCTORS, AS REQUIRED AFTER JANUARY 1, 2008 BY THE 2005 NEC ARTICLE 410.73G. PROVIDE EITHER FACTORY INSTALLED DISCONNECTING MEANS, OR PROVIDE FIELD INSTALLED DISCONNECT INSIDE THE BALLAST CHANNEL a. APPROVED FIELD - INSTALLED DISCONNECT 1) WAG() 873 2) TYCO /AMP LIGHT -N -LOK CPGI SERIES 3) T & B STA -KON LD2/LD3 SERIES 2. PROVIDE U.L. LISTED AND LABELED, C.B.M. APPROVED BALLASTS. 3. PROGRAMMED RAPID START TECHNOLOGY TO ENSURE LONGEST LAMP LIFE. 4. T8 ONLY: PARALLEL -WIRED OPERATION TO ENSURE LIGHT OUTPUT FROM ONE BALLAST EVEN WITH ONE OR TWO LAMPS EXTINGUISHED. 5. COMPACT FLUORESCENT ONLY: SERIES WIRED LAMPS FOR MULTIPLE LAMP CONFIGURATIONS, AND PLUG -IN LEAD CONNECTORS FOR ALL LAMP LEADS 6. CLASS "P" RATED WITH THERMALLY ACTIVATED AUTOMATIC RESETTING PROTECTIVE DEVICES SEALED IN HOUSING. 7. CURRENT CREST FACTOR: 1.7 OR LESS ON 60 HZ MODULATED CURRENT. 8. COMPLY WITH FCC RULES PART 18 REQUIREMENTS GOVERNING ELECTROMAGNETIC AND RADIO FREQUENCY INTERFERENCE 9. COMPLIES WITH IEEE 587 FOR WITHSTANDING LINE TRANSIENTS, VOLTAGE REGULATION ± 10 PERCENT, LIGHT REGULATION ±10 PERCENT. 10. BALLAST FACTOR: 0.88 OR HIGHER. 11. POWER FACTOR: GREATER THAN 95 PERCENT 12. SOUND RATING: "A" 13. MINIMUM 5 YEAR WARRANTY INCLUDING $10/BALLAST LABOR 14. TOTAL HARMONIC 0 0 T AL IARMONIG DISTORTION: 20 /o BUT GREATER TF IAN 10 /a 15. END -OF -LIFE LAMP SENSING FOR ALL COMPACT FLUORESCENT BALLASTS. H. APPROVED MANUFACTURERS - T8 ELECTRONIC BALLASTS 1. ADVANCE CENTIUM PROGRAM RAPID START SERIES 2. UNIVERSAL LIGHTING TECHNOLOGIES TRIAD ACCUSTART SERIES I. APPROVED MANUFACTURERS - COMPACT FLUORESCENT 1. MOTOROLA GOLD EDITION 2. ROBERTSON 3. OSRAM QUICKTRONIC SERIES 4. UNIVERSAL LIGHTING TECHNOLOGIES J. PROVIDE INSIDE FROSTED LAMPS WITH BRASS BASE, RATED 130 VOLTS FOR ALL INCANDESCENT LAMPS, UNLESS NOTED OTHERWISE. 1. APPROVED MANUFACTURERS A PHILIPS B. GENERAL ELECTRIC C. OSRAM/SYLVANIA D. PRE - APPROVED EQUAL K. PROVIDE MINIMUM 85 CRI FOR ALL FLUORESCENT LAMPS. PROVIDE 4100K COLOR LAMPS FOR ALL FLUORESCENT FIXTURES. L. M. N. 1. PROVIDE F032, F025 AND F017 T8 LAMPS FOR ALL 4', 3' AND 2' FIXTURES, RESPECTIVELY, UNLESS NOTED OTHERWISE. 2. APPROVED MANUFACTURERS: A. GE STARCOAT SPX B. PHILLIPS TL80 C. OSRAM SYLVANIA OCTRON 800XP PROVIDE SOLID STATE, SLID -TYPE DIMMERS SUITABLE FOR MOUNTING BEHIND A STANDARD DEPTH FACEPLATE AND FOR OPERATION ON COMMON NEUTRAL CIRCUITS. 1. PROVIDE 600 WATTS CAPACITY PER DIMMER UNLESS NOTED OTHERWISE ON THE PLANS. 2. ACCEPTABLE MANUFACTURERS: LUTRON NOVA T -STAR SERIES OR PRE- APPROVED EQUAL. SOLID STATE TYPE TIME SWITCHES. 1. PROVIDE SOLID STATE, PROGRAMMABLE 24 HOUR OR 7 -DAY, ELECTRIC TIME SWITCH WITH FOUR (4) SPST CONTACT RATED 20A AT 240 VOLTS. PROVIDE LONG LIFE LITHIUM BATTERY BACKUP TO MAINTAIN TIME AND MEMORY SETTING DURING A POWER OUTAGE 2. PROVIDE ASTRONOMICAL CONTROL. 3. ACCEPTABLE MANUFACTURERS A. PARAGON EC7000 SERIES B. TORK MODEL 0100 SERIES C. PRE - APPROVED EQUAL PROVIDE LIGHTING CONTACTORS THAT ADHERE TO THE FOLLOWING SPECIFICATIONS, WHERE LIGHTING CONTROL RELAYS OR CONTACTORS ARE CALLED OUT ON THE DRAWINGS: 1. ELECTRICALLY HELD RELAY, 30 AMP BALLAST RATED, 20 AMPS TUNGSTEN RATED @ 277 VOLTS 2. 2 POLE MINIMUM (REFER TO PLANS FOR REQUIRED POLES) 3. INSTALLED IN NEMA 1 ENCLOSURE INDOORS, NEMA 3R ENCLOSURE OUTDOORS. 4. COIL VOLTAGE: 24VAC. 5. COORDINATE ACCESSORIES WITH DIVISION 15'S EMS CONTRACTOR 6. APPROVED MANUFACTURERS: A. SQUARE D CLASS 8903, TYPE 'L' SERIES B. ASCO 917 SERIES C. SIEMENS TYPE CLM D. PRE - APPROVED EQUAL 0. PROVIDE PHOTOELECTRIC SWITCH CONTROL WITH A SET OF SPST CONTACTS RATED AT 1201(OLT AC, 1800VA IN A NEMA 3R ENCLOSURE. 1. UL LISTED. ,.._-. UILDIN 9 IVESI , 4 2. APPROVED MANUFACTURERS: A. PARAGON CW/210 SERIES B. TORK 2101 SERIES 3. IF USED AS A SENSOR INPUT TO THE LIGHTING CONTROL SYSTEM, PROVIDE PHOTOCELL CONTROLLERS FULLY - COMPATIBLE WITH THE LIGHTING CONTROL PANELS USED ON THIS PROJECT. REFER TO SECTION 16915. P. PROVIDE ALL HANGERS, RODS, MOUNTING BRACKETS, SUPPORTS, FRAMES, ETC. FOR PROPER AND SAFE FIXTURE INSTALLATION. INSTALL ALL FIXTURES IN ACCORDANCE WITH MANUFACTURERS' RECOMMENDATIONS AND INSTRUCTIONS. Q. PROVIDE FIXTURES COMPLETE WITH ALL AUXILIARIES REQUIRED FOR PROPER, SAFE AND DISTORTION FREE INSTALLATION IN THE VARIOUS CEILING CONSTRUCTIONS IN WHICH THEY APPEAR. COORDINATE CEILING TYPES WITH THE ARCHITECTURAL DRAWINGS AND PROVIDE COMPATIBLE FIXTURES. R. PROVIDE FELT OR FIBERGLASS GASKETS ON ALL INCANDESCENT LIGHTING FIXTURES WHERE NECESSARY TO PREVENT LIGHT LEAKAGE AT THE CEILING LINE. S. SECURELY SUPPORT ALL LIGHT FIXTURES DIRECTLY FROM BUILDING STRUCTURAL MEMBERS OR 11/2" OR LARGER STEEL CEILING FRAMING CHANNELS. USE STEEL CHANNEL EQUIVALENT TO KINDORF #6029 WHERE IT IS NECESSARY TO SPAN THE BUILDING STRUCTURAL MEMBERS FOR FIXTURE SUPPORT. WOOD SUPPORTING MEMBERS OR WIRES WILL NOT BE ACCEPTABLE. PROVIDE MINIMUM ' /d' DIAMETER LAG SCREWS WHEN ANCHORING INTO WOOD STRUCTURAL MEMBERS. WOOD STRUCTURAL MEMBERS A MINIMUM OF 2" WITH ALL SCREWS. PROVIDE STEEL OR PENETRATE W00 M LEAD, EXPANDABLE TYPE, ANCHORS WITH MINIMUM PENETRATION OF 11/2" WHEN ANCHORING TO CONCRETE. WHEN INSTALLING LIGHT FIXTURES IN A SEISMIC ZONE, SECURE TO MEET ALL REQUIREMENTS. T. DO NOT SUSPEND ANY CONDUIT, LIGHT FIXTURES, OR BALLASTS FROM METAL ROOF DECK OR FROM THE CEILING SUSPENSION WIRES. SUPPORT ALL LAY -IN FIXTURES INDEPENDENT OF THE CEILING SUPPORT SYSTEM. PROVIDE FASTENING CLIPS ON EACH CORNER OF EACH FIXTURE IN ACCORDANCE WITH THE UBC AND STATE BUILDING CODES. U. EQUIP ALL FIXTURES USING CONDUIT STEMS WITH BALL SWIVEL HANGERS. IN FINISHED AREAS, PROVIDE CANOPIES FOR THE HANGERS. V. SUPPORT ALL SURFACE MOUNTED FLUORESCENT FIXTURES WITH A MINIMUM OF ONE HANGER PER FIXTURE PLUS ONE PER ROW. SUPPORT INDIVIDUAL FIXTURES WITH A MINIMUM OF TWO HANGERS. ATTACH FIXTURE HANGERS TO THE CEILING GRID PER CODE. SUPPORT ALL SUSPENDED FLUORESCENT FIXTURES OF TWO FIXTURE HANGERS. W. S WITH H A MINIMUM I RE HAN E S. ATTACH EACH HANGAR TO A DEDICATED ANCHOR. LOCATE HANGARS DIRECTLY ABOVE THE CORNERS OF THE LIGHT FIXTURES. X WHERE MASTER/SLAVE OR INBOARD /OUTBOARD SWITCHING IS INDICATED, PROVIDE TANDEM -WIRED BALLASTS BETWEEN LIGHT FIXTURES AS REQUIRED BY THE LOCAL ENERGY CODE Y. WIRE ALL RECESSED LAY -IN FIXTURES WITH 6 FEET OF FLEXIBLE METAL CONDUIT WITH TYPE "THHN/THWN" WIRE TO THE OUTLET BOX PROVIDE GROUNDING TYPE CONNECTORS FOR ALL CABLE. CONDUIT ANDB ALE . Z. PROVIDE OUTLET BOXES ADJACENT TO EACH RECESSED FIXTURE OUTLET IN SUSPENDED CEILINGS TO PERMIT EACH FIXTURE TO BE ADJUSTED TO FIT CEILING PATTERN AND TO PERMIT "FEED THROUGH" WIRING. AA. AT THE TIME OF SUBSTANTIAL COMPLETION, ALL FIXTURES MUST BE INSTALLED AND LAMPED WITH NEW LAMPS. INSTALL ALL FIXTURES COMPLETE WITH LENSES, DIFFUSERS, REFLECTORS, LOUVERS AND OTHER REQUIRED ACCESSORIES. BB. REPLACE ANY DAMAGED REFLECTORS, DIFFUSERS, LOUVERS OR OTHER COMPONENTS AT NO EXPENSE TO THE OWNER. CC. CLEAN ALL FIXTURES FREE OF DUST, FINGER PRINTS, PAINT, ETC.. DD. PERFORM AIMING AND ADJUSTMENT OF ALL LIGHTING FIXTURES IN ACCORDANCE WITH INSTRUCTIONS ISSUED BY THE ENGINEER/TENANT. ADJUST ALL DIRECTIONAL TYPE FIXTURES (INTERIOR AND EXTERIOR) AFTER DARK UNDER THE DIRECTION OF THE ARCHITECT, ENGINEER, AND /OR TENANT. EE. REPLACE ALL DEFECTIVE BALLASTS WITHIN THE GUARANTEE PERIOD AT NO COST TO THE TENANT. FF. INSTALL DIMMERS WHERE INDICATED ON THE DRAWINGS. 1. WHERE DIMMERS ARE SHOWN GANGED WITH OTHER DIMMERS AND /OR OTHER DEVICES, SIZE OUTLET SUCH THAT DIMMERS WILL NOT BE UNDERATED. GG. INSTALL PHOTOCELL(S) PER MANUFACTURER'S RECOMMENDATIONS. 1. AIM AWAY FROM ARTIFICIAL LIGHT SOURCES SUCH AS STREET LIGHTS OR SECURITY LIGHTS. 2. SEAL PENETRATIONS THROUGH ROOF OR PENTHOUSE WALL. HH. INSTALL TIME SWITCHES ADJACENT TO THE SOURCE LIGHTING PANEL, UNLESS SPECIFICALLY LOCATED ELSEWHERE ON THE PLANS. 1. SET LONGITUDE AND LATITUDE SETTINGS AND THE ASTRONOMICAL TIME 2. PROVIDE TIME SETTINGS PER THE TENANT'S DIRECTION. MMM.PROVIDE "NAMEPLATES" A SPECIFIED IN SECTION 16050 FOR ALL CONTACTORS AND TIME SWITCHES. LABEL CONTACTORS AND TIME SWITCHES TO INDICATE LOAD SERVED (E.G., CANOPY LIGHTS, STORE SIGN, ETC.). 16535 - EMERGENCY LIGHTING R CODE COMP L NCE .APPROVED i City Of Tukwila- A PROVIDE AUTOMATIC BATTERY POWERED LIGHTING UNITS AS INDICATED ON THE DRAWINGS. B. PROVIDE EMERGENCY LIGHTING AS SHOWN ON THE PLANS TO ILLUMINATE THE EGRESS CORRIDORS AND OTHER REQUIRED AREAS. REFER TO THE LIGHT FIXTURE SCHEDULE ON THE DRAWINGS FOR TYPES. C. PROVIDE AN INTENSITY OF NOT LESS THAN 1.0 FOOTCANDLE AT THE FLOOR LEVEL ALONG THE PATH OF EGRESS. D. PROVIDE AN EXIT LIGHT AT EACH EXIT AND ALONG THE EGRESS PATH AS REQUIRED. 0. E. CONNECT EMERGENCY LIGHTS TO THE UNSWITCFIED BRANCH CIRCUIT(S) IN THE AREA PROVIDE HANDLE -LOCK DEVICE FOR THAT CIRCUIT. 16741 -VOICE AND DATA RACEWAY A PROVIDE 4" SQUARE BOXES FOR EACH RECESSED OUTLET BOX. PROVIDE 3'W DEEP MASONRY TYPE IN RECESSED MASONRY INSTALLATIONS. PROVIDE MUD OR TILE RING AS REQUIRED FOR ALL BOXES. B. PROVIDE THE FOLLOWING IN ACCESSIBLE CEILINGS AS FOLLOWS: PROVIDE AN EMPTY BOX WITH (1) 3/4" CONDUIT STUBBED INTO CEILING SPACE FOR EACH TELEPHONE OUTLET INDICATED ON THE DRAWINGS; PROVIDE AN EMPTY BOX WITH (2) 3/4" CONDUIT STUBBED INTO CEILING SPACE FOR EACH DATA, VOICE/DATA OR FIBER OPTIC OUTLET INDICATED ON THE DRAWINGS. C. PROVIDE THE FOLLOWING IN INACCESSIBLE CEILINGS (PLASTER, SPLINE, GYPSUM, SECURITY GRID, PLANK, ETC.) AS FOLLOWS: PROVIDE AN EMPTY BOX WITH (1) 3/4" CONDUIT ROUTED TO THE NEAREST TELEPHONE BACKBOARD LOCATION FOR EACH TELEPHONE OUTLET, UNLESS NOTED OTHERWISE ON THE PLANS; PROVIDE AN EMPTY BOX WITH (2) 3/4" CONDUIT ROUTED TO THE NEAREST COMMUNICATIONS CLOSET BACKBOARD LOCATION FOR EACH DATA, VOICE/DATA, OR FIBER OPTIC OUTLET, UNLESS NOTED OTHERWISE ON THE PLANS. DATE: JOB NO: 07/08/08 08- 0196.004 DRAWN: MDR CHECKED: SOR 711 N. FIELDER RD. ARLINGTON, TX 76012 PH: (817) 635 -5696 FAX: (817) 635 -5699 Project Coordination By 10 u ua 00 00 00 HALL' ''E ENGINEEIR Mechanical /Electrical Consulting Engineers 1750 Commerce Court, White Bear Luke, MN 55110 (651) 748 -1100 • Fax (651) 748 -9370 0 r- l'U "u tz REVISIONS 608-i69 i � �1` ECEIVED AUG 13 2008 PERMIT CENTER ELECTRICAL SPECIFICATIONS SHEET NUMBER E3