Loading...
HomeMy WebLinkAboutPermit D10-136 - FIBERDYNE LLC - TENANT IMPROVEMENTFIBERDYNE 17616 WEST VALLEY HY D10 -136 City olkukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us Parcel No.: 2523049017 Address: 17616 WEST VALLEY HY TUKW Suite No: DEVELOPMENT PERMIT Permit Number: D10 -136 Issue Date: 06/07/2010 Permit Expires On: 12/04/2010 Tenant: Name: FIBERDYNE LLC Address: 17616 WEST VALLEY HY , TUKWILA WA Owner: Name: BROMEL DAVID K Address: 3409 S LAURELHURST DR NE , SEATTLE WA 98105 Phone: Contact Person: Name: DIRK HALL Address: 14322 ADMIRALTY WY #44 , LYNWOOD WA 98087 Phone: 425 870 -6883 Contractor: Name: HALLCO Address: 14322 ADMIRALTY WAY #144 , LYNNWOOD WA 98037 Phone: 425 - 870 -6883 Contractor License No: HALLC**991QW Expiration Date: 11/16/2011 DESCRIPTION OF WORK: DEMOLITION OF TWO ROOMS, NUMEROUS NON - BEARING WALLS AND A FEW DOORS. EXISTING OPEN OFFICE AREA WILL BE USED AS A MANUFACTURING AREA (F -1) AS DEPICTED ON THE PLAN. NEW CABINETS WILL BE INSTALLED IN THE NEW BREAK ROOM FOR EMPLOYEES. MOST OF THE EXISTING OFFICE AREA WILL REMAIN AS IS. Value of Construction: $20,000.00 Fees Collected: $1,249.47 Type of Fire Protection: International Building Code Edition: 2006 Type of Construction: IIIB Occupancy per IBC: 0010 * *continued on next page ** doc: IBC -7/07 D10 -136 Printed: 06 -07 -2010 City ot Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Inspection Request Line: 206- 431 -2451 Web site: http: / /www.ci.tukwila.wa.us Permit Number: D10 -136 Issue Date: 06/07/2010 Permit Expires On: 12/04/2010 Public Works Activities: Channelization / Striping: N Curb Cut / Access / Sidewalk / CSS: 'N Fire Loop Hydrant: Flood Control Zone: Hauling: Land Altering: Landscape Irrigation: Moving Oversize Load: N N Number: 0 Size (Inches): 0 Start Time: Volumes: Cut 0 c.y. End Time: Fill 0 c.y. Start Time: End Time: Sanitary Side Sewer: Sewer Main Extension: Private: Public: Storm Drainage: Street Use: Profit: N Non - Profit: N Water Main Extension: Private: Public: Water Meter: N Permit Center Authorized Signature: Date: 12--?—to I hereby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances governing this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating construction or the performanc- • w- I am autho ' ed to sign and obtain this development permit. Signat • _ . J`f I i[ 1 Print Name: 1IQi�� • 14-411 Date: % '7 ^1D This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. doc: IBC -7/07 D10 -136 Printed: 06 -07 -2010 • City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us Parcel No.: 2523049017 Address: 17616 WEST VALLEY HY TUKW Suite No: Tenant: FIBERDYNE LLC PERMIT CONDITIONS Permit Number: D10 -136 Status: ISSUED Applied Date: 05/17/2010 Issue Date: 06/07/2010 1: ** *BUILDING DEPARTMENT CONDITIONS * ** 2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the Building Official. 3: All mechanical work shall be inspected and approved under a separate permit issued by the City of Tukwila Permit Center (206/431- 3670). 4: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to start of any construction. These documents shall be maintained and made available until final inspection approval is granted. 5: New suspended ceiling grid and light fixture installations shall meet the non - building structures seismic design requirements of ASCE 7. 6: Partition walls that are tied to the ceiling and all partitions greater than 6 feet m height shall be laterally braced to the building structure. 7: All construction shall be done in conformance with the approved plans and the requirements of the International Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code. 8: All rack storage requires a separate permit issued through the City of Tukwila Permit Center. Rack storage over 8 -feet in height shall be anchored or braced to prevent overturning or displacement during seismic events. The design and calculations for the anchorage or bracing shall be prepared by a registered professional engineer licensed in the State of Washington. 9: There shall be no occupancy of a building until final inspection has been completed and approved by Tukwila building inspector. No exception. 10: Remove all demolition rubble and loose miscellaneous material from lot or parcel of ground, properly cap the sanitary sewer connections, and properly fill or otherwise protect all basements, cellars, septic tanks, wells, and other excavations. Final inspection approval will be determined by the building inspector based on satisfactory completion of this requirement. 11: Manufacturers installation instructions shall be available on the job site at the time of inspection. 12: Ventilation is required for all new rooms and spaces of new or existing buildings and shall be in conformance with the International Building Code and the Washington State Ventilation and Indoor Air Quality Code. 13: Water heaters shall be anchored or strapped to resist horizontal displacement due to earthquake motion. Strapping shall be at points within the upper one -third and lower one -third of the water heater's vertical dimension. A minimum distance of 4- inches shall be maintained above the controls with the strapping. 14: All plumbing and gas piping work shall be inspected and approved under a separate permit issued by the Cityof Tukwila Permit Center. doc: Cond -10/06 D10 -136 Printed: 06 -07 -2010 • r City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Fax: 206 -431 -3665 Web site: http://www.ci.tukwila.wa.us 15: All electrical work shall be inspected and approved under a separate permit issued by the City of Tukwila Building Department (206- 431 - 3670). 16: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the Building Official from requiring the correction of errors in the construction documents and other data. 17: ** *FIRE DEPARTMENT CONDITIONS * ** 18: The attached set of building plans have been reviewed by the Fire Prevention Bureau and are acceptable with the following concerns: 19: The total number of fire extinguishers required for an ordinary hazard occupancy with Class A fire hazards is calculated at one extinguisher for each 1,500 sq. ft. of area. The extinguisher(s) should be of the "All Purpose" (2A, 20B:C) dry chemical type. Travel distance to any fire extinguisher must be 75' or less. (IFC 906.3) (NFPA 10, 3 -2.1) 20: The total number of fire extinguishers required for a light hazard occupancy with Class A fire hazards is calculated at one extinguisher for each 3,000 sq. ft. of area. The extinguisher(s) should be of the "all purpose" (2A, 10 B:C) dry chemical type. The travel distance to any extinguisher must be 75' or less. (IFC 906.3) (NFPA 10, 3 -2.1) 21: Fire extinguishers shall not be obstructed or obscured from view. In rooms or areas in which visual obstruction cannot be completely avoided, means shall be provided to indicate the locations of the extinguishers. (IFC 906.6) 22: Extinguishers shall be located in conspicuous locations where they will be readily accessible and immediately available for use. These locations shall be along normal paths of travel, unless the fire code official determines that the hazard posed indicates the need for placement away from normal paths of travel. (IFC 906.5) 23: Fire extinguishers require monthly and yearly inspections. They must have a tag or label securely attached that indicates the month and year that the inspection was performed and shall identify the company or person performing the service. Every six years stored pressure extinguishers shall be emptied and subjected to the applicable recharge procedures. If the required monthly and yearly inspections of the fire extinguisher(s) are not accomplished or the inspection tag is not completed, a reputable fire extinguisher service company will be required to conduct these required surveys. (NFPA 10, 4 -3, 4 -4) 24: Egress doors shall be readily openable from the egress side without the use of a key or special knowledge or effort. (IFC 1008.1.8.3 subsection 2.2) 25: Dead bolts are not allowed on auxiliary exit doors unless the dead bolt is automatically retracted when the door handle is engaged from inside the tenant space. (IFC Chapter 10) 26: Door handles, pulls, latches, locks and other operating devices on doors required to be accessible by Chapter 11 of the International Building Code shall not require tight grasping, tight pinching or twisting of the wrist to operate. (IFC 1008.1.8.1) 27: Exit hardware and marking shall meet the requirements of the International Fire Code. (IFC Chapter 10) 28: Exits and exit access doors shall be marked by an approved exit sign readily visible from any direction of egress travel. Access to exits shall be marked by readily visible exit signs in cases where the exit or the path of egress travel is not immediately visible to the occupants. Exit sign placement shall be such that no point in an exit access corridor is more than 100 feet (30,480 mm) or the listed viewing distance for the sign, whichever is less, from the nearest visible exit sign. (IFC 1011.1) 29: Every exit sign and directional exit sign shall have plainly legible letters not less than 6 inches (152 mm) high with the principal strokes of the letters not less than 0.75 inch (19.1 mm) wide. The word "EXIT" shall have letters having doc: Cond -10/06 D10 -136 Printed: 06 -07 -2010 • City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Fax: 206 - 431 -3665 Web site: http: //www.ci.tukwila.wa.us a width not less than 2 inches (51 mm) wide except the letter "I ", and the minimum spacing between letters shall not be less than 0.375 inch (9.5 mm). Signs larger than the minimum established in section 1011.5.1 of the International Fire Code shall have letter widths, strokes and spacing in proportion to their height. The word "EXIT" shall be m high contrast with the background and shall be clearly discernible when the exit sign illumination means is or is not energized. If an arrow is provided as part of the exit sign, the construction shall be such that the arrow direction cannot be readily changed. (IFC 1011.5.1) 30: Exit signs shall be illuminated at all times. To ensure continued illumination for a duration of not less than 90 minutes in case of primary power loss, the sign illumination means shall be connected to an emergency power system provided from storage batteries, unit equipment or on -site generator. (IFC 1006.1, 1006.2, 1006.3) 31: Means of egress, including the exit discharge, shall be illuminated at all times the building space served by the means of egress is occupied. The means of egress illumination level shall not be less than 1 foot -candle (11 lux) at the floor level. The power supply for the means of egress illumination shall normally be provided by the premise's electrical supply. In event of a power failure an emergency power system shall provide power for a duration of not less than 90 minutes and shall consist of storage batteries, unit equipment or on -site generator. (IFC 1006.1, 1006.2, 1006.3) The path of egress shall require emergency lighting until exit discharge is accomplished. 32: Aisles leading to required exits shall be provided from all portions of the building and the required width of the aisles shall be unobstructed. (IFC 1013.4) 33: Maintain sprinkler coverage per N.F.P.A. 13. Addition/relocation of walls, closets or partitions may require relocating and /or adding sprinkler heads. (IFC 901.4) 34: Sprinklers shall be installed under fixed obstructions over 4 feet (1.2 m) wide such as ducts, decks, open grate flooring, cutting tables, shelves and overhead doors. (NFPA 13- 8.6.5.3.3) 35: All new sprinkler systems and all modifications to existing sprinkler systems shall have fire department review and approval of drawings prior to installation or modification. New sprinkler systems and all modifications to sprinkler systems involving more than 50 heads shall have the written approval of the W.S.R.B., Factory Mutual, Industrial Risk Insurers Kemper or any other representative designated and /or recognized by the City of Tukwila, prior to submittal to the Tukwila Fire Prevention Bureau. No sprinkler work shall commence without approved drawings. (City Ordinance #2050) 36: Maintain fire alarm system audible /visual notification. Addition/relocation of walls or partitions may require relocation and/or addition of audible /visual notification devices. (City Ordinance #2051) 37: All new fire alarm systems or modifications to existing systems shall have the written approval of The Tukwila Fire Prevention Bureau. No work shall commence until a fire department permit has been obtained. (City Ordinance #2051) (IFC 104.2) 38: An electrical permit from the City of Tukwila Building Department Permit Center (206- 431 -3670) is required for this project. 39: All electrical work and equipment shall conform strictly to the standards of the National Electrical Code. (NFPA 70) 40: The maximum flame spread class of finish materials used on interior walls and ceilings shall not exceed that set forth in Table No. 803.5 of the International Building Code. 41: New and existing buildings shall have approved address numbers, building numbers or approved building identification placed in a position that is plainly legible and visible from the street or road fronting the property. These numbers shall contrast with their background. Address numbers shall be Arabic numbers or alphabet letters. Numbers shall be a minimum of 4 inches (102mm) high with a minimum stroke width of 0.5 inch (12.7mm). (IFC 505.1) 42: This review limited to speculative tenant space only - special fire permits may be necessary depending on detailed description of intended use. doc: Cond -10/06 D10 -136 Printed: 06 -07 -2010 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Fax: 206 - 431 -3665 Web site: http://www.ci.tukwila.wa.us 43: Contact The Tukwila Fire Prevention Bureau to witness all required inspections and tests. (City Ordinances #2050 and #2051) 44: Any overlooked hazardous condition and/or violation of the adopted Fire or Building Codes does not imply approval of such condition or violation. 45: These plans were reviewed by Inspector 511. If you have any questions, please call Tukwila Fire Prevention Bureau at (206)575 -4407. * *continued on next page ** doc: Cond -10/06 D10 -136 Printed: 06 -07 -2010 • City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us I hereby certify that I have read these conditions and will comply with them as outlined. All provisions of law and ordinances governing this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority • violate or cancel the provision of any other work or local laws regulating construction or the performance of work. Signature: Print Name: k t(A 11 Date: 6 - 7 doc: Cond -10/06 D10 -136 Printed: 06 -07 -2010 CITY OF TUKWILA Community Development Department Public Works Department Permit Center 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 http://www.ci.tulcwila.wa.us Building Permit No. Mechanical Permit No. Plumbing/Gas Permit No. Public Works Permit No. 10 Project No. (For office use only) Applications and plans must be complete in order to be accepted for plan review. Applications will not be accepted through the mail or by fax. * *Please Print ** SITE LOCATION Site Address: 17600 West Valley Highway, Tukwila WA Tenant Name: Fiberdyne LLC Property Owners Name: North valley LLC c/o David Bromel Mailing Address: 3409 W. Laurelhurst Dr. N.E. King Co Assessor's Tax No.: 252304901702 Suite Number: 17,616 Floor: 1 New Tenant: Yes ❑ ..No Seattle WA 98105 City State Zip CONTACT PERSON - who do we contact when your permit is ready to be issued Name: Mailing Address: Day Telephone: E -Mail Address: City State Zip Fax Number: GENERAL CONTRACTOR INFORMATION — (Contractor Information for Mechanical (pg 4) for Plumbing and Gas Piping (pg 5)) Company Name: N/A at this time }die //,o Mailing Address: /V362 .2 Aa/m,AA /7'y I )y "f4' L,.y4f41sv £0,4 76'08 7 Ci State Zip Day Telephone'-6:1 975 -5883 Fax Number'jS) 7s 7 ^ /0 3/ Expiration Date: // •/G -i/ Contact Person: 1i?t< ,NA 1/ E -Mail Address:WA /7GO S e.4/// 14/ SAP A Contractor Registration Number: /iiQ //G `99 /Q[ci ARCHITECT OF RECORD - All plans must be wet stamped by Architect of Record Company Name: Lance Mueller Architects Mailing Address: 130 Lakeside, Suite 250 Contact Person: Harold Christensen Seattle WA 98122 E -Mail Address: haroldc @Imueller.com City State Day Telephone: (206) 325 -2553 Fax Number: (206) 325 -2553 Zip ENGINEER OF RECORD - All plans must be wet stamped by Engineer of Record Company Name: N/A Mailing Address: City State Zip Contact Person: Day Telephone: E -Mail Address: Fax Number: H:\Applications \Forms - Applications On Line\2009 Applications \1 -2009 - Permit Application.doc Revised: 1 -2009 bh Page 1of6 • • BUILDING PERMIT INFORMATION - 206 - 431 -3670 °O Existing Building 5,962,800 Valuation of Project (contractor's bid price): $ 0 D � 4 D � Existin Buildin Valuation: $ Scope of Work (please provide detailed information): DEMOLITION OF TWO ROOMS, NUMEROUS NON - BEARING WALLS AND A FEW DOORS. EXISTING OPEN OFFICE AREA WILL BE USED AS A MANUFACTURING AREA (F -1) AS DEPICTED ON THE PLAN. NEW CABINETS WILL BE INSTALLED IN THE NEW BREAK ROOM FOR EMPLOYEES. MOST OF THE EXISTING OFFICE AREA WILL REMAIN AS IS. Will there be new rack storage? ® Yes D.. No If yes, a separate permit and plan submittal will be required. Provide All Building Areas in Square Footage Below PLANNING DIVISION: Single family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches) 0 *For an Accessory dwelling, provide the following: Lot Area (sq ft): Floor area of principal dwelling: Floor area of accessory dwelling: *Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence. Number of Parking Stalls Provided: Standard: 130 Compact: 0 Handicap: 5 Will there be a change in use? ❑ Yes ❑ No If "yes ", explain: FIRE PROTECTION/HAZARDOUS MATERIALS: m Sprinklers 0 Automatic Fire Alarm ❑ None ❑ Other (specify) Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ Yes ❑ No If `yes', attach list of materials and storage locations on a separate 8 -1/2" x II" paper including quantities and Material Safety Data Sheets. SEPTIC SYSTEM ❑ On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health Department. H:\Applications\ Forms - Applications On Line\2009 Applications \I -2009 - Permit Application.doc Revised: 1 -2009 bh Page 2 of 6 Existing Interior Remodel Addition to Existing Structure New Type of Construction per IBC Type of Occupancy per IBC 1' Floor 108,632 603 III B SPRNK B,M,S -1,F -1 2nd Floor 4,261 III B SPRNK B 3rd Floor Floors thru Basement Accessory Structure* Attached Garage Detached Garage Attached Carport Detached Carport Covered Deck Uncovered Deck PLANNING DIVISION: Single family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches) 0 *For an Accessory dwelling, provide the following: Lot Area (sq ft): Floor area of principal dwelling: Floor area of accessory dwelling: *Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence. Number of Parking Stalls Provided: Standard: 130 Compact: 0 Handicap: 5 Will there be a change in use? ❑ Yes ❑ No If "yes ", explain: FIRE PROTECTION/HAZARDOUS MATERIALS: m Sprinklers 0 Automatic Fire Alarm ❑ None ❑ Other (specify) Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ Yes ❑ No If `yes', attach list of materials and storage locations on a separate 8 -1/2" x II" paper including quantities and Material Safety Data Sheets. SEPTIC SYSTEM ❑ On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health Department. H:\Applications\ Forms - Applications On Line\2009 Applications \I -2009 - Permit Application.doc Revised: 1 -2009 bh Page 2 of 6 PERMIT APPLICATION NOTES — Applicable to all permits in this application Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject to possible revision by the Permit Center to comply with current fee schedules. Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation. Building and Mechanical Permit The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be requested in writing and justifiable cause demonstrated. Section 105.3.2 Intemational Building Code (current edition). Plumbing Permit The Building Official may grant one extension of time for an additional period not exceeding 180 days. The extension shall be requested in writing and justifiable cause demonstrated. Section 103.4.3 Uniform Plumbing Code (current edition). I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING OWNER OR AUTHORIZED A ENT: Signatur Print Name: Harold Christensen Mailing Address: 130 Lakeside, Suite 250 Date: 5-- /T / Day Telephone: (206) 325 -2553 Seattle WA 98122 City State Zip Date Application Accepted: S^ / 7 - /D Date Application Expires: L 1 �� t Staff Initials: H. Applications\ Forms - Applications On Line\2009 Applications\I -2009 - Permit Application.doc Revised: 1 -2009 bh Page 6 of 6 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us Parcel No.: 2523049017 Address: 17616 WEST VALLEY HY TUKW Suite No: Applicant: FIBERDYNE LLC RECEIPT PAYMENT RECFIVED Permit Number: D10 -136 Status: ISSUED Applied Date: 05/17/2010 Issue Date: 06/07/2010 Receipt No.: R10 -01399 Initials: User ID: Payee: LAW 1632 Payment Amount: $63.00 Payment Date: 07/23/2010 01:50 PM Balance: $0.00 HALLCO TRANSACTION LIST: Type Method Descriptio Amount Payment Check 5260 63.00 Authorization No. ACCOUNT ITEM LIST: Description Account Code Current Pmts PLAN CHECK - NONRES 000.345.830 63.00 Total: $63.00 doc: Receiot -06 Printed: 07 -23 -2010 • • C �����a��w�s City of Tukwila a ' °"fib' � 0 Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Fax: 206 - 431 -3665 Web site: http://www.ci.tulcwila.wa.us Parcel No.: 2523049017 Address: 17616 WEST VALLEY HY TUICW Suite No: Applicant: FIBERDYNE LLC RECEIPT Permit Number: D10 -136 Status: APPROVED Applied Date: 05/17/2010 Issue Date: Receipt No.: R10 -00995 Initials: User ID: WER 1655 Payment Amount: $944.10 Payment Date: 06/07/2010 09:43 AM Balance: $0.00 Payee: HALLCO TRANSACTION LIST: Type Method Descriptio Amount Payment Check 5214 944.10 Authorization No. ACCOUNT ITEM LIST: Description Account Code Current Pmts BUILDING - NONRES STATE BUILDING SURCHARGE 000.322.100 640.237.114 Total: $944.10 939.60 4.50 PAYMENT REC FIFD doc: Receipt -06 Printed: 06 -07 -2010 1 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 -431 -3670 Fax: 206 - 431 -3665 Web site: http://www.ci.tukwila.wa.us RECEIPT ParcelNo.: 2523049017 Permit Number: D10 -136 Address: 17600 WEST VALLEY HY TUKW Status: PENDING Suite No: Applied Date: 05/17/2010 Applicant: FIBERDYNE LLC Issue Date: Receipt No.: R10 -00864 Payment Amount: $305.37 Initials: JEM Payment Date: 05/17/2010 03:51 PM User ID: 1165 Balance: $474.30 Payee: HALLCO TRANSACTION LIST: Type Method Descriptio Amount Payment Check 5188 305.37 Authorization No. ACCOUNT ITEM LIST: Description Account Code Current Pmts PLAN CHECK - NONRES 000.345.830 305.37 Total: $305.37 PAYMENT RECEIVED doc: Receiot -06 Printed: 05 -17 -2010 INSPECTION NO. CITY OF TUKWILA BUILDING 6300 Southcenter Blvd., #100, Tukwila. WA 98188 Permit Inspection Request Lire (206) 431 -2451 INSPECTION RECORD Retain a copy with permit IWO --)3 c1 PERMIT NO. V. DIVISION P"' (206) 431 -3670 Project:. ( A Type o ipection: Address: 17 l (e l"...i . kki 1 if-, Date Called: Special Instrr7ctrons: / 16 Date Wanted: r Requester: Phone No rkpproved per applicable codes. Corrections required prior to approval. 2 COMMENTS: fc° • otat. 1 l s� � e % I-- i 14.4/ 00V1t13AA,if Aip/rnroe, r: ALI 1 Dart 1 1t //0 INSPECTION FEE R QUIRED: Prior tooext inspection; fee must be aid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. d`i'p rot. cRM ir. s • -sr . a.:.. ro'a-. +r.ftQa• -•7 •. •. .1 i+ j.. •r. .r -• r.re r • .. - groLi /1 INSPECTION NO. INSPECTION RECORD Retain a copy with permit PERMIT NO. • CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (2O6) 431 -3670 Permit. Inspection Request Line (206) 431 =2451 �j . Project: - ' - ��w? ,/'3M V A/A 4L Type of Inspection: ∎=-7AM --- Address: 17t' / 4.kg r.AZkei Date Called: Special Instructions: i d fr- Date Wa ted: Requester: ' -• Phone No: - 4517'... el3 7©.. b88? • Ei Approved per applicable codes. • O Corkctions required prior to approval. COMMENTS: .414 e /_ s1..- . (t . rn • , �- 40 AietatMeei t 4 4/6-43- ._ c C9 not 7_f•) ,Ms' ) /•7(le .6 a! /1 Ale /..` Tbbv1. r4,440( / �r.��o..-rc..,/l /24�or ��� 1,07,011L7 3� it NSPECTION FE : vino. Prior to next inspection. fee must be : id at 6300 Southcente Blvd.. Suite i00. Call to schedule reinspection. J b� M� • . • 5 n.:. .. •awr.: Yb+ INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION I2- 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 Oro- '3c Pro g'r .DYNE Type of Inspection: e.tne .r . L� / �C� 1 Address: 1`16(c uU - UM(e Date Called: % Special Instructions: / Date Wanted:-7 d a.m.' --(,c) - 2- p.m. Requester: PhLie2 90`'_GL'83 Approved per applicable codes. Corrections required prior to approval. COMMENTS: -e rs rest ---�5 1 1-02 Inspgctor: Date:- / _ . ( O ri $60.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Receipt No.: Date: J INSPECTION RECORD Retain a copy with permit 1.I6 - 13 INSPECTION NO. PERMIT,,NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 Pro'ect: 'I lame. t rk\(OE Type of Inspection: kemc /OP; 11Nc ;i nts1(I - Address: I7 (_ 1 C- L.Jp,\ l) (A ∎( ac-1 Date Called: Special Instructions: Date Wanted: -7 -2.4)-1c) p.m. Requester: Phone No: H2 - 37o -bS9 approved per applicable codes. El Corrections required pridy to approval. COMMENTS: spec or: e: REQUIRE/Prior 1$6 v 0( pa f at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Recei •'t No.: 'Date: INSPECTION NO. INSPECTION RECORD Retain a copy with permit CITY OF TUKWILA BUILDING DIVISION 1�- 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 Project : /L' /_ C'llyAE Type of Inspection: c es<",irFr° /6FAO G., n/ / N Ci Address: X76'6, ,5/�T /fy Date Called: 7 —,5 -,U Special Instructions: Date Wanted: 1/ .2.z - 970 -688 3 m� o Requester: Phone No: 4_ • Approved per applicable codes. COMMENTS: Corrections required prior to approval. /it Inspecttr: Date �) 1 AA El $60.00 REINSPECTION FEE REQUIRED. Prior to inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Receipt No.: Date: INSPECTION NO. INSPECTION RECORD Retain a copy with permit -'34 PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 Projec i —1 • ,y /� j �j J C 9� 6/ • " v. r Type of I,'ns]p�ection: +t^ Address: W ! r , /I� / ji-'l ( Date Called: Special Instructions: fff Date Wanted: / (k " 3 p.m. Requester: Phone No: "'] Approved per applicable codes. V" Corrections required prior to approval. COMMENTS: . lv/3 — 479pcovgc/ 6.14 %_ALs >,t Air d1vi — 4l9(Ale Date: 6--/ d —ice $ • 0.0 REINSPECTION FEE R OUIRED.'Prior to inspection, fee must be p: id =t 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Recei No.: 'Date: 3 INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 4-n oro Proje J ` be /- Ai' /� ` 1 i— Type of Inspectionn:, * AA co . 4 ` C Address: P7 (i W- - (/.Q- -f/� Date Called: Special Instructions: �� Date Wanted: C9 - (8-∎(c) a.m. p.m. Requester: Phone No: 2 S- g'70 -Co e'3 s.s414.4 Approved per applicable codes. Corrections required prior to approval. COM ENTS: Insp Date: $60.00 paid Receip No.: INSPECTION FEE REQ ED. • for to inspection, fee must be 6300 Southcenter Blvd., Su. to 100. Call to schedule reinspection. Date: INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 11" 6300 Southcenter Blvd., #100, Tukwila, WA 98188 (206)431 -3670 Of() (.3‘ Project, U �� �� (� Type °f- ra. mil tio� ; t 4 6 � / Address: Date Called: Special Instructions: I Date Wanted: r I , to _ap.m. lS' Requester: Phone No: - 15""gr10— 03 Approved per applicable codes. El Corrections required prior to approval. G COMMENTS: � f� yi Inspect Date: y 1 / 0 6.00 REINSPECTION FF E REQVIRED. Prior to inspection, fee must be Id at 6300 Southcenter'Blvd., Suite 100. Call to schedule reinspection. Re ipt No.: Date: INSPECTION NO. INSPECTION RECORD Retain a copy with permit Oro - l3() CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila, WA 98188 PERMIT NO. t Y` (206)431 -3670 Prod 'gerDt- ^f - ',Type f Inspection: ,g..e d,(,av-e Stvf Wiwi Address: / Date Called: Special Instructions: Date Wanted: aim., (0 _ q - to p.m. Requester: Phone No:_ f� 425 -/ O- Co3 3 J Approved per applicable codes. Corrections required prior to approval. COMMENTS: ./J/ STOP STO% (JJof e 1.-)g.rogLAO -ctor, ice... Aid P' +0 REINSPECTION 'EE REQUIR . Prior to inspection, fee must be • at 6300 Southcente Blvd., S • e 100. Call to schedule reinspection. Date/ 7 --7n Receipt No.: Date: 1 INSPECTION NUMBER INSPECTION RECORD Retain a copy with permit b ►o- /3(d PERMIT NUMBERS CITY OF TUKWILA FIRE DEPARTMENT 444 Andover Park East, Tukwila, Wa. 98188 206 - 575 -4407 Project: cl: b d-d J - L L T ype of Ins 4e ction: . r rc. c iut - Address: r -� , j b Suite #: (». 04.1) i H Contact Person: bi Special Instructions: Ph'o. /ne No.: RIApproved per applicable codes. Corrections required prior to approval. COMMENTS: C t,-c -Q: iAL 8k- Needs Shift Inspection: Sprinklers: Fire Alarm: Hood & Duct: Monitor: Pre -Fire: Permits: Occupancy Type: , Inspector: SP- Date: OP -'7! /4 Hrs.: / $80.00 REINSPECTION FEE REQUIRED. You will receive an invoice from the City of Tukwila Finance Department. Call to schedule a reinspection. Word /Inspection Record Form.Doc 1/13/06 T.F.D. Form F.P. 113 tlnterior 2006 Washington State Nonresidential Energy Code Compliance Form tin'g'Summ'ary 2006 Washington State Nonresidential Energy Code Compliance Forms LTG -INiT Revised July 2007 Project Info Project Address FIBERDYNE Date 5/20/2010 17616 WEST VALLEY HIGHWAY For Building Department Use FILE COPY _... TUKWILA, WA 98188 Applicant Name: HAROLD CHRISTENSEN Applicant Address: 130 LAKESIDE, SUITE 250, SEATTLE WA 98122 Applicant Phone: 206- 325 -2553 ^. .all,, Project Description ❑ Plans Included requirements. ❑ New Building ❑ Addition -I Alteration Refer to WSEC Section 1513 for controls and commissioning Compliance Option 0 Prescriptive 0 Lighting Power Allowance 0 Systems Analysis (See Qualification Checklist (over). Indicate Prescriptive & LPA spaces clearly on plans.) Alteration Exceptions (check appropriate box - sec. 1132.3) ❑ No changes are being made to the lighting ❑ Less than 60% of the fixtures new, installed wattage not increased, & space use not changed. Maximum Allowed Lighting Wattage Location (floor /room no.) Occupancy Description Allowed Watts per ft2 "" Area in ft2 Allowed x Area RM 106 & 107 B 1.00 603.0 603.0 ** From Table 15 -1 (over) - document all exceptions on form LTG -LPA Total Allowed Watts 603.0 Proposed Lighting Wattage Location (floor /room no.) Fixture Description Number of Fixtures Watts/ Fixture Watts Proposed 1ST 2'x4' LAY -IN FLUORESCENT (2 -TUBE) 8 61.0 488.0 Total Proposed Watts may not exceed Total Allowed Watts for Interior Total Proposed Watts 488.0 Notes: 1. For proposed Fixture Description, indicate fixture type, lamp type (e.g. T -8), number of lamps in the fixture, and ballast type (if included). For track lighting, list the length of the track (in feet) in addition to the fixture, lamp, and ballast information. 2. For proposed Watts /Fixture, use manufacturer's listed maximum input wattage of the fixture (not simply the lamp wattage) and other criteria as specified in Section 1530. For hard -wired ballasts only, the default table in the NREC Technical Reference Manual may also be used. For track lighting, list the greater of actual luminaire wattage or length of track multiplied by 50, or as applicable, •f current - limiting devices or of the transformer. i R � . ,4:, 11 � l ', ^IZ' mpt lighting, note section and exception number, and leave Watts /Fixture blank. CODE COMPLIANCE A������® INCOMPLETE JUN 0 �4 2010 RED D LTR #_�._,_ cmr S I&LA MAY 21 2010 City of Tukwila PERMIT CENTER PI 0- 1 3(4f BUILDING ran /�� m d 2006 Washington State Nonresidential Energy Code Compliance Form e.rior:l .tiynPv _. ..• _ ti, tog : "Sumr1i ryt(bac 2006 Washington Slate Nonresidential Energy Code Compliance Forms Revised July 2007 Prescriptive Spaces Occupancy: Q Warehouses, storage areas or aircraft storage hangers Q Other Qualification Checklist Note: If occupancy type is "Other" and fixture answer is checked, the number of fixtures in the space is not limited by Code. Clearly indicate these spaces on plans. If not qualified, do LPA Calculations. Lighting Fixtures: (Section 1521) Check if 95% or more of fixtures comply with 1,2 or 3 and rest are ballasted. 1. Fluorescent fixtures which are non - lensed with a) 1 or 2 two lamps, b) reflector or louvers, c) 5 -60 watt T -1, T -2, T-4, T -5, T -8 lamps, and d) hard -wired elec- tronic dimming ballasts. Screw -in compact fluorescent fixtures do not qualify. 2. Metal Halide with a) reflector b) ceramic MH lamps <= 150w c) electronic ballasts 3. LED lights. TABLE 15 -1 Unit Liahtina Power Allowance (LPA Use' LPA` (W /sf) Use' LPA` (W /sf) Automotive facility 0.9 Office buildings, office /administrative areas in facilities of other use types (including but not limited to schools, hospitals, institutions, museums, banks, churches) 1.0 Convention center 1.2 Penitentiary and other Group 1 -3 Occupancies 1.0 Courthouse 1.2 Police and fire stations" 1.0 Cafeterias, fast food establishments', restaurants /bars5 1.3 Post office 1.1 Dormitory 1.0 Retail10, retail banking, mall concourses, wholesale stores (pallet rack shelving) 1.5 Exercise center 1.0 School buildings (Group E Occupancy only), school classrooms, day care centers 1.2 Gymnasia'', assembly spaces'' 1.0 Theater, motion picture 1.2 Health care clinic 1.0 Theater, performing arts 1.6 Hospital, nursing homes, and other Group 1 -1 and 1 -2 Occupancies 1.2 Transportation 1.0 Hotel /motel 1.0 Warehouses1', storage areas 0.5 Hotel banquet/conference /exhibition ha113.4 2.0 Workshops 1.4 Laboratory spaces (all spaces not classified "laboratory" shall meet office and other appropriate categories) 1.8 Parking garages 0.2 Laundries 1.2 Libraries' 1.3 Plans Submitted for Common Areas Only' Manufacturing facility 1.3 Main floor building lobbies3 (except mall concourses) 1.2 Museum 1.1 Common areas, corridors, toilet facilities and washrooms, elevator lobbies 0.8 Footnotes for Table 15 -1 1) In cases in which a general use and a specific use are listed, the specific use shall apply. In cases in which a use is not mentioned specifically, the Unit Power Allowance shall be determined by the building official. This determination shall be based upon the most comparable use specified in the table. See Section 1512 for exempt areas. 2) The watts per square foot may be increased, by two percent per foot of ceiling height above twenty feet, unless specifically directed otherwise by subsequent footnotes. 3) Watts per square foot of room may be increased by two percent per foot of ceiling height above twelve feet. 4) For all other spaces, such as seating and common areas, use the Unit Light Power Allowance for assembly. 5) Watts per square foot of room may be increased by two percent per foot of ceiling height above nine feet. 6) Reserved. 7) For conference rooms and offices less than 150ft2 with full height partitions, a Unit Lighting Power Allowance of 1.10 w /ft2 may be used. 8) Reserved. 9) For indoor sport tournament courts with adjacent spectator seating over 5,000, the Unit Lighting Power Allowance for the court area is 2.60 W /ft2. 10) Display window illumination installed within 2 feet of the window, provided that the display window is separated from the retail space by walls or at least three - quarter- height partitions (transparent or opaque). and lighting for free - standing display where the lighting moves with the display are exempt. An additional 1.5 w /ft2 of merchandise display luminaires are exempt provided that they comply with all three of the following: a) located on ceiling- mounted track or directly on or recessed into the ceiling itself (not on the wall). b) adjustable in both the horizontal and vertical axes (vertical axis only is acceptable for fluorescent and other fixtures with two points of track attachment). c) fitted with LED, tungsten halogen, fluorescent, or high intensity discharge lamps. This additional lighting power is allowed only if the lighting is actually installed. 11) Provided that a floor plan, indicating rack location and height, is submitted, the square footage for a warehouse may be defined: for computing the interior Unit Lighting Power Allowance, as the floor area not covered by racks plus the vertical face area (access side only) of the racks. The height allowance defined in footnote 2 applies only to the floor area not covered by racks. 4. May 19, 2010 • City of [tiI'\1:lla Jim Haggerton, Mayor Department of Community Development Dirk Hall 14322 Admiralty Wy #44 Lynnwood WA 98087 RE: Incomplete Letter #1 Development Permit Application D10 -136 Fiberdyne —17600 West Valley Hy Dear Mr. Hall, Jack Pace, Director This letter is to inform you that your permit application received at the City of Tukwila Permit Center on May 17, 2010 is determined to be incomplete. Before your application can continue the plan review process the attached /following items from the following department(s) need(s) to be addressed: Building Department: Allen Johannessen at 206 433 -7163 if you have any questions concerning the attached comments. Please address the attached comment in an itemized format with applicable revised plans, specifications, and /or other documentation. The City requires that four (4) sets of revised plans, specifications and /or other documentation be resubmitted with the appropriate revision block. In order to better expedite your resubmittal a `Revision Submittal Sheet' must accompany every resubmittal. I have enclosed one for your convenience. Revisions must be made in person and will not be accepted through the mail or by a messenger service. If you have any questions, please contact me at the Permit Center at (206) 431 -3670. Sincerely, Jen fifer Marshall Pe it Technician Enclosures File: D10 -136 WAPermit CenterUncomplete Letters \2010\D10 -136 Incomplete Ltr # 1.DOC 6300 Southcenter Boulevard, Suite #100 • Tukwila, Washington 98188 • Phone: 206 - 431 -3670 • Fax: 206 - 431 -3665 1 Tukwila Building Division Allen Johannessen, Plan Examiner Determination of Completeness Memo Date: May 18, 2010 Project Name: Fiberdyne LLC Permit #: D10 -136 Plan Review: Allen Johannessen, Plans Examiner The Building Division has deemed the subject permit application incomplete. To assist the applicant in expediting the Department plan review process, please forward the following comments. (GENERAL NOTE) PLAN SUBMITTALS: (Min. size 11x17 to maximum size of 24x36; all sheets shall be the same size). (If applicable) Structural Drawings and structural calculations sheets shall be original signed wet stamped, not copied.) 1. Provide a floor plan that identifies means of egress for the office and warehouse. Dimension egress paths. Identify path of egress illumination on the plan to show common paths of egress are provided with emergency illumination. Emergency illumination shall have at least an average 1 foot - candle and a minimum at any point of 0.1 foot candle measured along the path of egress at the floor level. Emergency lighting shall also be required for exit discharge doorways. (IBC Section 1006) 2. The plan shows exits out the back of the warehouse. An emergency egress path shall not be allowed through open storage or warehouse unless the path is a demarcated minimum 44 inch wide aisle defined by full or partial height fixed walls or similar construction that will maintain the required width and lead directly to the exit without obstructions or possibility thereof. Please revise egress plan to show provisions for a protected exit access path. (IBC 1014.2 #2.4) 3. In addition to item 2), exit access doorways shall not be less than one -third of the length of the maximum overall diagonal dimension of the area served. Two exits are required; however the two exits at the front will not meet the two exit requirements with the 1/3 diagonal dimension. Therefore the rear exits would meet the requirement with the demarcated path indicated in item 2). For information only in reference to item 2). (IBC 1015.2.1 Exception 2) 4. Complete a 2006 Washington State Nonresidential Energy Code Lighting Compliance Form. Should there be questions concerning the above requirements, contact the Building Division at 206 -431- 3670. No further comments at this time. • PERMIT COM COPYI PLAN REVIEW /ROUTING SLIP ACTIVITY NUMBER: D10 -136 DATE: 07/19/10 PROJECT NAME: FIBERDYNE SITE ADDRESS: 17616 WEST VALLEY HY Original Plan Submittal Response to Correction Letter # Response to Incomplete Letter # X Revision # 1 after Permit Issued DEPART E TS: 10 ling 'vision �i A/�/�� 1 -Y' 10 u Iic WoriCs� A///1- 1:11-t 0 Fire Prevention Structural -A, M1- - -(0 Planning Division ❑ Permit Coordinator DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete VI, Comments: Incomplete n DUE DATE: 07/20/10 Not Applicable Permit Center Use Only INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED: Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: TUES /THURS ROUTING: Building Please Route I XI REVIEWER'S INITIALS: Structural Review Required n No further Review Required ❑ DATE: APPROVALS OR CORRECTIONS: Approved tZ( Notation: REVIEWER'S INITIALS: Approved with Conditions DUE DATE: 08/17/10 Not Approved (attach comments) DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: Documentshouting slip.doc 2 -28 -02 •ERT COON COPY 40 PLAN REVIEW /ROUTING SLIP ACTIVITY NUMBER: D10 -136 DATE: 05/21/10 PROJECT NAME: FIBERDYNE LLC SITE ADDRESS: 17600 WEST VALLEY HY Original Plan Submittal Response to Correction Letter # X Response to Incomplete Letter # 1 Revision # after Permit Issued DEPARTMENTS: uil.ing D'vision Udk Public Wor s Fire Prevention Structural SM DC/141-GI Planning Division nPermit Coordinator ❑ DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete Comments: t� f Incomplete ❑ DUE DATE: 05/25/10 Not Applicable Permit Center Use Only INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED: Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: TUES /THURS ROUTING: Building Please Route Structural Review Required n No further Review Required ❑ REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: DUE DATE: 06/22/10 Approved n Approved with Conditions ye Not Approved (attach comments) n Notation: REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: Documents/routing slip.doc 2 -28 -02 IERiTC'nRD COPV 1. PLAN REVIEW /ROUTING SLIP ACTIVITY NUMBER: D10 -136 DATE: 05/17/10 PROJECT NAME: FIBERDYNE LLC SITE ADDRESS: 17600 WEST VALLEY HY X Original Plan Submittal Response to Correction Letter # Response to Incomplete Letter # Revision # after Permit Issued DEPARTMENTS: Building Division Public Works I Fire Prevention Structural Planning Division ❑ Permit Coordinator DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete ❑ Comments: Incomplete DUE DATE: 05/18/10 Not Applicable Permit Center Use Only INCOMPLETE LETTER MAILED: Departments determined incomplete: Bldg i4 Fire ❑ Ping ❑ PW ❑ Staff Initials: LETTER OF COMPLETENESS MAILED: TUES /THURS ROUTING: Building Please Route ❑ Structural Review Required ❑ No further Review Required REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: Approved ❑ Approved with Conditions Notation: REVIEWER'S INITIALS: DUE DATE: 06/15/10 Not Approved (attach comments) ❑ DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: Documents/routing slip.doc 2 -28 -02 PROJECT NAME: SITE ADDRESS: 1 PERMIT NO: , o- 1 L ORIGINAL ISSUE DATE: CU 1,01 1l REVISION LOG REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS 1 tiO tAlli0 1N`- O J -3 //o tit() Summary of Revision: fi-tkft pvT b n T k(�' Qw/o k pk t(r b Received by: D'4* D • AO /l REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Received by: (please print) REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Received by: (please print) REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Received by: (please print) REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Received by: (please print) REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Received by: (please print) • City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us REVISION SUBMITTAL Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: July 19, 2010 Plan Check/Permit Number: D10 -136 ❑ Response to Incomplete Letter # ❑ Response to Correction Letter # • Revision # t after Permit is Issued • Revision requested by a City Building Inspector or Plans Examiner Project Name: Project Address: Contact Person: Fiberdyne RECEIVED CITY OF A im, mom PERMIT rr. 17616 West Valley Highway, Tukwila WA f/ Phone Number: ya5- 6740- 664_3 Summary of Revision: Revised exit travel distance numbers to match current design. Revised layout of new fenced exit aisle from office and manufacturing area to rear exit door. Reivsed chain link gate /door size. Revised reflected ceiling plan to show change. Detail 8/TA4.0 deleted from plan set. Revised door type and door schedule to show revised chain link gate /door size. Sheet Number(s): TA2.1, TA3.0 and TA4.0 "Cloud" or highlight all areas of revision including date of revision Received at the City of Tukwila Permit Center by Fi Entered in Permits Plus on d7// 9/ D A6) \applications\forms- applications on line\revision submittal Created: 8 -13 -2004 Revised: 1 -2009 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http://www.ci.tukwila.wa.us REVISION SUBMITTAL' Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: Plan Check/Permit Number: D10-136 ® Response to Incomplete Letter # 1 ❑ Response to Correction Letter # RECevED jEl Revision # / after Permit is Issued CITY OF / n Revision requested by a City Building Inspector or Plans Examiner MAY 21 201(I Project Name: Fiberdyne LLC Project Address: 17600 West Valley Hy PERMIT CENTER Contact Person: 72 ,'4k //4/// Phone Number:6;15) 6'Z', -- 883 Summary of Revision: 4IIe d ex sT, AA J A-A kr- yn �� r4 -„ cam d���o ti N , PAA -Vide p t w d e-4- ( ..� u e� t .s.�.c �� e( , 1- A• t s le... Pea OW. m 4' a ,4'4 e.,e a^ ,!.¢, - K a - 4.44►a1 4444 4-o ReAR e1.*IQ . 12e-woad je...4 1e-c lied 6e--1 Iiw9 p/AV • Ek1'- Sy A) im .• a.- •S 4- C..•t s:A -- A • S+ e�. ► me R g cke d u t d u e. -1—e, .vv U e4 A'•e i e_-e-• e44 s /-e— . Sheet Number(s): "Cloud" or highlight all areas of revision including date of revision Received at the City of Tukwila Permit Center by: Entered in Permits Plus on \applications \forms - applications on line \revision submittal Created: 8 -13 -2004 Revised: LANCE MUELLER & ASSOCIATES A R C H I T E C TS A I A May 20, 2010 Allen Johannessen Plans Examiner City of Tukwila 6300 Southcenter Boulevard, Suite #100 Tukwila, WA 98188 RE: Fiberdyne T.I. — Permit #D10- 136- Incomplete letter #1 Dear Allen, We received your incomplete letter #1 comments dated May 20, 2010. We have attached our response comments below. Below I have addressed each numeric comment on your letter. I use the same numeral below as your letter. 1. Please see attached revised sheet TA2.1. We have added exit pathway diagrams to the plan from each major area with the distance labeled at each location. During the previous tenant occupancy process, emergency egress lighting was added throughout the building (office and warehouse). This current tenant has painted the entire warehouse floor with white epoxy paint and they do not have plans at this time to utilize high storage racks. The current permit plans specify that the emergency exit pathway lighting is to comply with IBC section 1006. The tenant will provide any additional emergency lighting if any areas are found to be deficient. 2. Please see attached revised sheet TA2.1. The revised plans show a chain link enclosure to exit door at the rear of the building. Sheet TA3.0 shows new exit signs with pathway lighting for this area as well. Sheet TA4.0 shows new doors added for this revision. 3. With plan attached plan changes, I do not think we have any issue with this comment. 4. Please see attached copies of the 2006 Washington State Nonresidential Energy Code Lighting Compliance Form for the ceiling area with lighting changes per this permit. We hope the attached response and plans will satisfy your concerns. If you have any questions or concerns regarding the corrected plans, please call me to discuss. I can be reached at 206 - 325 -2553. Thank you very much, 444424 Harold Christensen Architect Lance Mueller & Associates 130 Lakeside Suite 250 Seattle, WA 98122 (206) 325 -2553 Fax (206) 328 -0554 Architecture Planning Space Planning Interiors 1 Contractors or Tradespeople P,,ter Friendly Page • General /Specialty Contractor A business registered as a construction contractor with L &I to perform construction work within the scope of its specialty. A General or Specialty construction Contractor must maintain a surety bond or assignment of account and carry general liability insurance. Business and Licensing Information Name Hallco UBI No. 600530388 Phone 4258706883 Status Active Address 14322 Admiralty Way #44 License No. HALLC" 991QW Suite /Apt. License Type Construction Contractor City Lynnwood Effective Date 11/16/2001 State Wa Expiration Date 11/16/2011 Zip 98037 Suspend Date County Snohomish Specialty 1 General Business Type Individual Specialty 2 Unused Parent Company Business Owner Information Name Role Effective Date Expiration Date Hall, Dirk Owner 11/16/2001 Bond Information Page 1 of 1 Bond Bond Company Name Bond Account Number Effective Date Expiration Date Cancel Date Impaired Date Bond Amount Received Date 2 DEVELOPERS STY & INDEMNITY CO 571661C 10/30/2003 Until Cancelled $12,000.00 10/08/2003 Assignment of Savings Information No records found for the previous 6 year period Insurance Information Insurance Company Name Policy Number Effective Date Expiration Date Cancel Date Impaired Date Amount Received Date 8 NEVADA CAPITOL INS CO 77NPP4001769 10/30/2008 10/30/2010 $1,000,000.00 10/14/2009 7 NEVADA CAPITOL INS CO NCIC000213 10/30/2008 10/30/2009 $1,000,000.00 10/14/2008 6 MAXUM INDEMNITY CO BDG00016715 10/30/2007 10/30/2008 $500,000.00 10/29/2007 5 MAXUM INDEMNITY CO BDG0001671- 04 10/30/2005 10/30/2007 $500,000.00 10/13/2006 4 INDEMNITY CO BDG0001671 10/30/2004 10/30/2005 $1,000,000.00 10/05/2004 3 DEVELOPERS STY & INDEMNITY CO BDG0001671 10/30/2003 10/30/2004 $1,000,000.00 10/08/2003 Summons /Complaint Information No unsatisfied complaints on file within prior 6 year period Warrant Information No unsatisfied warrants on file within prior 6 year period https: // fortress .wa.gov /lni/bbip /Print.aspx 06/07/2010 715' -O" 60' -0" 60' -0" 60' -0" BREAK ROOM (1 19) 0 SEPARATE PERMIT REQUIRED FOR: IieMechanic al l Electrical I"Plumbing ( as Piping City of Tukwila ,U= LF'ING DIVISION EXIT PREMANUFACTURED PAINT BOOTH (UNDER SEPARATE PERMIT) EXIT NOTE: PLACEMENT OF FUTURE CURING OVEN TO BE DETERMINED BY MANUFACTURERS RECOMENDATIONS AND COMPLIANCE WITH I.B.C. AT TIME OF PERMIT APPLICATION (UNDER SEPARATE PERMIT). NEW 8' -0" HIGH CHAINLINK ENCLOSURE WITH (1) 6'- 0 "x7' -8" C.L. DOOR / LEVER HARDWARE NEW SERVICE SINK. TIE TO EXISTING SEWER LINE CAPPED AT BASE OF COLUMN. MANUFACTURING/ STORAGE (126) OUTLINE OF PREVIOUS RESTROOMS IX ' � 1 PREMANU- 1 FACTURED , CURING OVENX (UNDER I SEPARATE PERMIT) IX T 6' -0" IELD VERIFY 1 CV VENDING MACHINES REVISIONS No changes shall be made to the scope of work without prior approval of Tukwila Building Division. NOTE44evisions will require a new plan submittal and may include additional plan review fees. PROVIDE NEW EXIT SIGNS WITH ARROW MANUFACTURING PROVIDE NEW 3'- 0 "x7' -0" HOLLOW METAL DOOR AND FRAME POST SIGN ON CHAIN LINK GATE FACE "NOT AN EXIT" PROVIDE POWER, DRAIN AND WATER SUPPLY FOR TENANT SUPPLIED WASHER AND DRYER. _ PROVIDE NEW PAIR 3'- 0 "x7' -0" HOLLOW METAL X DOORS AND X RAMEX FUTURE EMPLOYEE LOCKERS N ENLARGED PLAN AT BREAK ROOM Scale: 1 /4 " =1' -0" FILE COPY 'Nit). i #ice la A11111=0. OFFIC INFILL EXISTING NOTE: COMPLY EXISTING EMERGENCY EMERGENCY EXIT PATHWAY LIGHTING TO WITH I.B.C. SECTION 1006. (BOTH AND NEW COMPONENTS OF OFFICE EGRESS ILLUMINATION) NOTE: UNDER RACKING WITHIN WAREHOUSE TO BE SEPARATE , PERMIT. 000 _ 1 1` N 1 `n 1 LO cu` O FENCED EXIT AISLE REVISION INCOMPLETE LETTER #1 REVISIONS PERMIT APPLICATION SET I c 0 (1, 0 L N ,--- 6 c •ou qof 990-01 c _ 'v checked O_ I r- N tr% 13 EXIT PREMANUFACTURED PAINT BOOTH (UNDER SEPARATE PERMIT) EXIT NOTE: PLACEMENT OF FUTURE CURING OVEN TO BE DETERMINED BY MANUFACTURERS RECOMENDATIONS AND COMPLIANCE WITH I.B.C. AT TIME OF PERMIT APPLICATION (UNDER SEPARATE PERMIT). NEW 8' -0" HIGH CHAINLINK ENCLOSURE WITH (1) 6'- 0 "x7' -8" C.L. DOOR / LEVER HARDWARE NEW SERVICE SINK. TIE TO EXISTING SEWER LINE CAPPED AT BASE OF COLUMN. MANUFACTURING/ STORAGE (126) OUTLINE OF PREVIOUS RESTROOMS IX ' � 1 PREMANU- 1 FACTURED , CURING OVENX (UNDER I SEPARATE PERMIT) IX T 6' -0" IELD VERIFY 1 CV VENDING MACHINES REVISIONS No changes shall be made to the scope of work without prior approval of Tukwila Building Division. NOTE44evisions will require a new plan submittal and may include additional plan review fees. PROVIDE NEW EXIT SIGNS WITH ARROW MANUFACTURING PROVIDE NEW 3'- 0 "x7' -0" HOLLOW METAL DOOR AND FRAME POST SIGN ON CHAIN LINK GATE FACE "NOT AN EXIT" PROVIDE POWER, DRAIN AND WATER SUPPLY FOR TENANT SUPPLIED WASHER AND DRYER. _ PROVIDE NEW PAIR 3'- 0 "x7' -0" HOLLOW METAL X DOORS AND X RAMEX FUTURE EMPLOYEE LOCKERS N ENLARGED PLAN AT BREAK ROOM Scale: 1 /4 " =1' -0" FILE COPY 'Nit). i #ice la A11111=0. OFFIC INFILL EXISTING NOTE: COMPLY EXISTING EMERGENCY EMERGENCY EXIT PATHWAY LIGHTING TO WITH I.B.C. SECTION 1006. (BOTH AND NEW COMPONENTS OF OFFICE EGRESS ILLUMINATION) NOTE: UNDER RACKING WITHIN WAREHOUSE TO BE SEPARATE , PERMIT. NOTE: THIS TENANT WILL NOT USE OR STORE HAZARDOUS MATERIALS BEYOND EXEMPT QUANTITIES ALLOWED PER THE I.B.C. AND I.F.0 F -1 MANUFACTURING AREA & S -1 STORAGE WAREHOUSE RELOCATE EXISTING DOOR TO ACCOMMODATE NEW WALL. NEW INSULATED WALL TO ALIGN WITH EXISTING WALL REMOVED. EXISTING FULL HEIGHT DEMISING WALL. INFILL EXISTING OPENING IN WALL AND PROVIDE NEW 3'- 0 "x7' -0" HOLLOW METAL DOOR AND FRAME= COUNTER HEIGHT Plar-revlew-approvals _.st..to ertols °rll�°ns._ . . 5 rovat of construction documents does not authorize 'ion of any adopted code or ordinance. - ~-ipt ci approved Field Co. and t • ', ., is : N t 1 1 ' f ; Date: , 7 3 `�� City Of Tukwila BUILDING DIVISION MICROWAVE OUTLET AT UPPER COUNTER HEIGHT MICROWAVE OUTLET AT UPPER 6 -7%4 PRODUCT FINISH ROOM (123) OPEN OFFICE (1 10) FABRIC LAY UP (109) c1 N 1 N ;::: CNTR. HGHT. \ �— COUNTER, HEIGHT' SECURE STORAGE (121) - � I i �"-- -- DEDH. T CNTR. yV HGT. r ITCHE J DED. (107) DW. O O 220V N) .`, BREAK ROOM REMOVE EXISTING DOOR AND FRAME AND INFILL I EXISTING OPENING. CREATE NEW 3'- 6 "x7' -0" 1 OPENING IN EXISTING WALL.: 1 7, 1 1 I NEW ,.COUNTER WITH CABINETS BELOW s. RF. WOMEN •1 J' OPEN OFFICE 110 MEN LOCKER CO N • }_ +VA: - KITCHEN BREAK ROOM (106) 1 0" PANTRY STORAGE NEW COUNTERS 1 W/ CABINETS I BELOW AND I ABOVE AS SHOWN PROVIDE 2' -0" RADIUS ON CORNER OF EXISTING WALL. NOTE: SCREENED LINE WITH ARROW AT EXIT DOORS DEPICT EGRESS PATH AND DISTANCE FROM REMOTE POINTS WITHIN OFFICE, WAREHOUSE AND MANUFACTURING SPACE. 75 L.F. ORIGIN POINT DISTANCE OF PATH PATH EXIT POINT FIRST FLOOR PLAN Scale: 1 /8 " =1' -0" L 0 OFFICE (1 18) LOCKER WOMEN LOCKER (1 1 6) MAI N CONFERENE€ (1 n< COPY /FAX (114) OUTLINE OF EXISTING SECOND FLOOR OFFICE ABOVE 0 N) SEATING (1 o1) L. QEP [ 0J - - (100) OFFICE (102) 0 1 23 ENLARGED PLAN AT KITCHEN Scale: 1 /4 " =1' -0" EXISTING STAIRS BELOW. END OF CABINET PANTRY STORAGE (108) 16' -6" REVIEWED FOR CODE COMPLIANCE APPPfVED JUL 2 3 2010 AT City of Tukwila BUILDING DIVISION REVISION N0. STAI R EXISTING FIRST FLOOR ENTRY /LOBBY. EXISTING MAIN ENTRY DOORS BELOW. DN OPIEN, Of OFFICE 201) OCCUPANT LOAD FIBERDYNE OPEN OFFICE (THIS AREA) 8 OCCUPANTS 24' -8" ce O RECEIVE CITY OF TUKWILA JUL 19 2010 PERMIT CENTER (0 03 M z J (1 a J 0 SECOND FLOOR PLAN (EXISTING) (776 S.F. SECOND FLOOR OFFICE AREA) Scale: 1/8 " =1' -0" H IX co w O u) to 0 w U Z a I— J I— I— W w U 2 U Q 0 W 0 sheet TA2.1 0 3' -0" X 7' -0" HOLLOW METAL DOOR W/ H.M. FRAME W/ 7 "x37" TEMPERED GLASS LITE IN MTL. FRAME DOOR TYPES PAIR 3' -0" X 7' -0" HOLLOW METAL DOORS W/ H.M. FRAME W/ 7 "x37" TEMPERED GLASS LITE IN MTL. FRAME W /BLACK KICKPLATES. (EACH SIDE) STEEL PLATES EACH SIDE FOR MOUNTING LEVER HARDWARE 3' -0" X 7' -0" X Y" TEMP. GLASS DOOR W/ 1 DIA. X 12' PULL AND 30" PUSH BAR. 6' -0" (x 7' -8" CHAIN ■ LINK DOOR DOOR & WINDOW NOTES 1. ALL DOOR HARDWARE TO COMPLY WITH I.B.C. SECTION 1008, WAC 51 -50 AND A.D.A. 2. PROVIDE INTERNATIONAL SYMBOL OF ACCESS SIGNAGE AT EACH ACCESSIBLE ENTRANCE DOOR. (MAIN ENTRANCE AND EMPLOYEE ENTRANCE) 3. ALL EXIT DOORS SHALL BE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR ANY SPECIAL KNOWLEDGE OR EFFORT PER I.B.C. SECTION 1008.1.8 4. PROVIDE SAFETY GLAZING PER DRAWINGS AND I.B.C. SECTION 2406. T= TEMPERED GLAZING. Scale: 1 /4 " =1' -0' 5/8" TYPE 'X' GWB EACH SIDE OVER METAL STUDS ® 24" O.C. SEE WALL TYPE PAINTED H.M. FRAME TYP. SILENCERS STRIKE SIDE INSULATION PER WALL TYPE. 0 DOOR AS - SCHEDULED HOLLOW METAL DOOR JAMB /HEAD Scale: 3' =1' -0" roe IWO i w 14� R -25 BATT INSULATION OVER NEW OPEN OFFICE AREA SUSPENDED CEILING SYSTEM PER REFLECTED CEILING PLAN 6" X 20 GA. METAL STUDS ® 24" O.C. WITH 5/8" TYPE "X" GWB EACH SIDE (PAINT OPEN OFFICE SIDE ONLY) R -21 BATT INSULATION AT INTERIOR PERIMETER WALLS 1/8" DIA. X 1" POWDER ACTUATED FASTENERS CD 24" O.C. BASE PER SCHEDULE EXIST. CONC. FLOOR SLAB WALL AT PERIMETER Scale: 1 /2 " =1' -0" NOT USED A 0 0 0 0 C J -J Li z EXISTING OPENING TO BE il? itiiit ifiiI? uifiMEliAil«?uNft(1i11?Mllj RAI i 11 P= R -25 BATT INSULATION OVER ENTIRE NEW CEILING AREA. CEILING PER REFLECTED CEILING PLAN SOUND BATT INSULATION 3 5/8" X120 GA: METAL STUDS 24" O.C. WITH 5/8" TYPE "X" GWB EACH SIDE. (PAINT), STAGGER STUDS WHERE WALL TO BE INFILLED IS GREATER THAN 4 s". 1 /8" DIA. X 1" POWDER ACTUATED ;FASTENERS 24" O.C. BASE PER SCHEDULE EXIST. CONC. FLOOR SLAB WALL INFILL AT EXISTING WALL A I DOOR SCHEDULE DOOR NO. T DESCRIPTION DOOR FRAME HARDWARE GROUP RATING REMARKS MAT. FIN. MAT. FIN. 106 C 3'- 0 "x7' -0" . GLASS FACT. - - - - 109A A 3'- 0"x7' -0" HM PAINT HM PAINT - - 0 N 0 0 109B A 3'-0"x7' -0 HM PAINT HM PAINT - - 109C B PAIR 3'- 0 "x7' -0" HM PAINT HM PAINT - - 110 A 3'- 0 "x7' -O" HM PAINT HM PAINT - - 125 D 6'- 0 "x7' -8" CHAINLINK GALV. STEEL GALV. - I - DOORS DESIGNATED "E" ON PAN ARE EXISTING WITH NO CHANGE PER THIS PERMIT. DOOR SCHEDULES POSTS AT 10' -0" MAX. OR AS FOR 8 -0" HIGH ENCLOSURE HORIZONTAL TOP & BOTTOM RAIL TYPICAL WELD n CONCRETE SLAB GALV, STEEL BASE PLATE W/ ANCHOR BOLTS TO EXISTING SLAB. FENCE BASE PLATE Scale: 3' =1' -0" Scale: 1 /2 " =1' -0" 8' -0" HIGH CHAIN — LINK ENCLOSURE PER PLAN. REVIEWED FOR CODE COMPLIANCE APPROVED JUL 2 3 2010 City of Tukwila BUILDING DIVISION CITY OF TUKWILA JUL. 19 2010 PERMIT CENTER (0 rn M N U 0 1- Z W WW oZ 1- CC zW zm li. SCHEDULES ckS cn J Q w in w 0 H 0 0 co MUELLER a • co U w I- I U rx M N N N M O c0 N N a) SEATTLE 0 w 0 130 LAKES sheet TA4.0 000 yi cp rn0. NCI i 7 a) 0 FENCED EXIT AISLE REVISION INCOMPLETE LETTER #1 REVISIONS PERMIT APPLICATION SET C 0 • _ a i N •— O C . co o o .00 c 3 _ checked 0 N 0 0 (0 rn M N U 0 1- Z W WW oZ 1- CC zW zm li. SCHEDULES ckS cn J Q w in w 0 H 0 0 co MUELLER a • co U w I- I U rx M N N N M O c0 N N a) SEATTLE 0 w 0 130 LAKES sheet TA4.0 U o=e oz.> ...II —r- UUANA! EXISTING BUILDING STATISTICS VICINITY MAP ARCHITECT / CONTACT PERSON LANCE MUELLER & ASSOCIATES 120 LAKESIDE, SUITE 250 SEATTLE, WA 98122 (206) 325 -2553 (206) 328 -0554 FAX CONTACT PERSON: HAROLD CHRISTENSEN OWNER / APPLICANT NORTH VALLEY LLC 3409 W. LAURELHURST DR. N.E. SEATTLE, WA 98105 (206) 264 -5577 (206) 264 -5577 FAX CONTACT PERSON: DAVE BROMEL FIBERDYNE TENANT IMPROVEMENT ALL WORK THIS PERMIT WI HIN HATCHED AREA. SEE PLANS) r• TENANT FIBERDYNE 17616 WEST VALLEY HIGHWAY TUKWILA, WA 98188 (425) 970 -6354 (425) 988 -6343 FAX CONTACT PERSON: STEVEN ZACK ,EVIS`NS No dianges shall be made to the scope of work without prior approval of 'Tukwila Building Division. NOTE: Revisions MI rewire a in-! Wan submittal and may include additional pi-, n review fees. .:. FILE COPY Perwdt No , 10- Ptan NNW/ approval kisubOct boron and one. Approval of construction documents does not authorize the violation of any adopted code or off. Receipt of approved Field Copy and =lions is Date:. G ' 7 - / City Of Tukwila BUILDING DIVISION SEPARATE PERMIT REQUIRED FOR rrYlumbing as City of Tukwila BLJ1L DING DIVISION VAAL :.( T' r l :. :: - CONSTRUCTION TYPE (2006 I.B.C. OCCUPANCY TYPE (EXISTING) SITE AREA (COUNTY RECORDS) BUILDING AREA(S): EXISTING BUILDING A (COUNTY RECORDS) PARKING PROVIDED III -B SPRINKLED B, S -1, M (NON SEPARATED) 6.38 ACRES 112,893 S.F. 138 STALLS TENANT IMPROVEMENT STATISTICS TENANT: CODE: OCCUPANCY: SITE ZONING: PERMITTED USE IN C /LI ZONE: EXISTING BUILDING: MAX. ALLOWABLE BUILDING AREA: OCCUPANCY SEPARATION: ENERGY CODE: LIGHTING POWER NOT CHANGED. TENANT AREA: FIBERDYNE 2006 IBC, IFC, IPC, IMC, ICC /ANSI A117.1 B,S- 1, &F -1 C /LI EXISTING USE TYPE III -B, SPRINKLED. UNLIMITED AREA (SEPARATION ALL SIDES) PROPOSED NON- SEPARATED USE PER I.B.C. SECTION 302.3.1 (MOST RESTRICTIVE USE ANTICIPATED - F -1) BUDGET ATTACHED. THERMAL PERFORMANCE OFFICE AREA (B) (EXISTING FIRST FLR. & MEZZ.) MANUFACTURING (F -1) (EXISTING B TO BE USED AS F -1) WAREHOUSE (S -1) MANUFACTURING (F -1) TOTAL TENANT AREA (FOP BU LD NG DEPARTMENT USE ONLY.) REQUIRED PARKING (THIS TENANT) OFFICE 8,029 S.F. x 3/1,000 = WAREHOUSE 9,353 S.F. x 1/2,000 = MANUFACTURING 11,345 S.F. x 1/1,000 = 8,029 S.F. 1,992 S.F. 9,353 S.F. 9,353 S.F. 28,727 S.F. 24 STALLS 4.6 STALLS 11.3 STALLS TOTAL (THIS TENANT) 71 STALLS DESCRIPTION OF WORK FIBERDYNE IS A NEWLY ESTABLISHED TOOLING AND ENGINEERING COMPANY THAT SPECIALIZES IN THERMOSET CARBON FIBER. THIS FACILITY WILL BE USED FOR ENGINEERING, TOOLING AND MODELING FOR PROTOTYPE OF ALL THEIR PRODUCTS. THE FACILITY WILL ALSO SERVE AS THE MARKETING AND SALES CENTER. EXISTING WAREHOUSE AREA WILL BECOME THE MANUFACTURING AREA WITH STORAGE. EXISTING OFFICE AREA WILL REMAIN OFFICE AND ROOM 109 (EXISTING OFFICE) WILL BECOME A MANUFACTURING AREA. SEE PLANS FOR CHANGES TO EXISTING SPACE. vr1: °• i' .. . $`► k4 .. 72c,. °te ;. 3o 6161(a. evil 14?.t&x9 _4,1■1 P ...i/. _.0t_. _ LEGAL DESCRIPTION, TAX #'S, ADDRESS THE SOU i H 329.85' OF THAT PORTION OF GOVERNMENT LOT 7 IN SECTION 25, TOWNSHIP 23 NORTH, RANGE 4 EAST, W.M., IN KING COUNTY WASHINGTON LYING WEST OF PUGET SOUND TRACTION, LIGHT & POWER RIGHT -OF -WAY AND SOUTHEASTERLY OF A LINE CONVEYED TO THE STATE OF WASHINGTON BY WARRANTY DEED RECORDED UNDER KING COUNTY RECORDING N0. 747163. EXCEPT THE EAST 15 FEET THEREOF FOR ROAD AND LANE PURPOSES. TAX ACCOUNT NUMBER 252304901702 INDEX OF DRAWINGS TA1.0 SITE PLAN / COVER SHEET TA2.0 OVERALL BUILDING PLAN, DEMOLITION PLAN TA2.1 FIRST FLOOR PLAN, ENLARGED PLANS TA2.2 . INTERIOR ELEVATIONS, DETAILS TA3.0 REFLECTED CEILING PLANS, DETAILS TA4.0 DOOR TYPES, DETAILS & SCHEDULES DEFERRED SUBMITTALS * ELECTRICAL SYSTEMS._ .DESIGN AND PERMIT * MECHANICAL SYSTEMS DESIGN AND PERMIT * FIRE SPRINKLER SYSTEM MODIFICATIONS AND PERMIT * FIRE ALARM SYSTEM MODIFICATIONS AND PERMIT * CURING OVEN DESIGN AND PERMIT PAINT BOOTH DESIGN AND PERMIT Exist: F y, 101 28 Zco vf. -- 0 1o'' Jo' X 4'' C (1c, 1%1-10 1/-41 `rt-t iC tl.k:b�11 ric.N . de, HHS • I' rif'414 rer# Zad -• • • • .4•. raM- ATM i 7/9',ZZ 173/ rzArdfr A fritleiCrAelrA 8 REVIEWED FOR CODE COMPLIANCE APPROVED JUN 0.4 2010 AQ-3- City of Tukwila BUILDING DIVISION V. 120 t GEI D _ CITY RE OF T I WILA MAY 172010 PERMIT CENTER north • /fr OVERALL SITE PLAN Scale: 1 "= 30' -0" 4c710-13cv 5 -17 -10 D 13 PERMIT APPLICATION SET revision 10 -068 job no. HC drawn checked 0 I I (1) p DESCRIPTION OF WORK FIBERDYNE IS A NEWLY ESTABLISHED TOOLING AND ENGINEERING COMPANY THAT SPECIALIZES IN THERMOSET CARBON FIBER. THIS FACILITY WILL BE USED FOR ENGINEERING, TOOLING AND MODELING FOR PROTOTYPE OF ALL THEIR PRODUCTS. THE FACILITY WILL ALSO SERVE AS THE MARKETING AND SALES CENTER. EXISTING WAREHOUSE AREA WILL BECOME THE MANUFACTURING AREA WITH STORAGE. EXISTING OFFICE AREA WILL REMAIN OFFICE AND ROOM 109 (EXISTING OFFICE) WILL BECOME A MANUFACTURING AREA. SEE PLANS FOR CHANGES TO EXISTING SPACE. vr1: °• i' .. . $`► k4 .. 72c,. °te ;. 3o 6161(a. evil 14?.t&x9 _4,1■1 P ...i/. _.0t_. _ LEGAL DESCRIPTION, TAX #'S, ADDRESS THE SOU i H 329.85' OF THAT PORTION OF GOVERNMENT LOT 7 IN SECTION 25, TOWNSHIP 23 NORTH, RANGE 4 EAST, W.M., IN KING COUNTY WASHINGTON LYING WEST OF PUGET SOUND TRACTION, LIGHT & POWER RIGHT -OF -WAY AND SOUTHEASTERLY OF A LINE CONVEYED TO THE STATE OF WASHINGTON BY WARRANTY DEED RECORDED UNDER KING COUNTY RECORDING N0. 747163. EXCEPT THE EAST 15 FEET THEREOF FOR ROAD AND LANE PURPOSES. TAX ACCOUNT NUMBER 252304901702 INDEX OF DRAWINGS TA1.0 SITE PLAN / COVER SHEET TA2.0 OVERALL BUILDING PLAN, DEMOLITION PLAN TA2.1 FIRST FLOOR PLAN, ENLARGED PLANS TA2.2 . INTERIOR ELEVATIONS, DETAILS TA3.0 REFLECTED CEILING PLANS, DETAILS TA4.0 DOOR TYPES, DETAILS & SCHEDULES DEFERRED SUBMITTALS * ELECTRICAL SYSTEMS._ .DESIGN AND PERMIT * MECHANICAL SYSTEMS DESIGN AND PERMIT * FIRE SPRINKLER SYSTEM MODIFICATIONS AND PERMIT * FIRE ALARM SYSTEM MODIFICATIONS AND PERMIT * CURING OVEN DESIGN AND PERMIT PAINT BOOTH DESIGN AND PERMIT Exist: F y, 101 28 Zco vf. -- 0 1o'' Jo' X 4'' C (1c, 1%1-10 1/-41 `rt-t iC tl.k:b�11 ric.N . de, HHS • I' rif'414 rer# Zad -• • • • .4•. raM- ATM i 7/9',ZZ 173/ rzArdfr A fritleiCrAelrA 8 REVIEWED FOR CODE COMPLIANCE APPROVED JUN 0.4 2010 AQ-3- City of Tukwila BUILDING DIVISION V. 120 t GEI D _ CITY RE OF T I WILA MAY 172010 PERMIT CENTER north • /fr OVERALL SITE PLAN Scale: 1 "= 30' -0" 4c710-13cv r,r• t' ri �yy6 is r.4 --wry ii3ir!'Ffi fr. f/ SLPIT S.F. S-w F w (OCC. L 4.4 y�ig,� iG7.e (7.e4. f /� 4 ,,..�' .1 fr d s / f rte° s 0 4. *40 J.irXSF+,R '4•A yus ?ate a VACAN SPEC FLOC TRA RING ALL SPORTS ( VENTURI TECHNOLOGIES KANKAN �HY� `iYr:GY 4440 ':SF. izt % .5 OCCU .7,263 (OCC. kyil4 06%1 .05.Si& f A 44' rtFp , �Y /.Gf 9f4'`Nr 52 ifj j %lij•∎00 f`!.0 L.% f.: 1111111 m e OVERALL BUILDING PLAN Scale: 1"=20'-0" TOTAL OCC LOAD FOR 213 OCCUP UPANT FIBERDYNE ANTS B OCCUP. (ABOVE 776 OF (O.L. 8) CD L- LEXISTING /' a r M r I I IL —! Ivry` 9I �i•R; -+R 1F • a L EXISTING OFFICE AREA r up -4 1I „ -I 1* 7 T LI I1 A11 I I III -I- _ III I 'I DEMOLITION PLAN N.T.S. DEMOLITION KEYNOTES 0 0 0 0 0 0 DEMOLISH AND REMOVE EXISTING CHAIN LINK FENCE ENCLOSURE. REMOVE PORTION OF EXISTING WALL FOR NEW MAN DOOR. SEE FLOOR PLAN. REMOVE EXISTING DOOR AND FRAME. REMOVE PORTION OF EXISTING WALL FOR NEW WALL RADIUS. SEE FLOOR PLAN. REMOVE PORTION OF EXISTING WALL FOR NEW GLASS DOOR AND FRAME. SEE FLOOR PLAN. REMOVE PORTION OF EXISTING WALL, DOOR AND FRAME TO CREATE 7' -O” HIGH OPENING FROM RECEPTION. SEE FLOOR PLAN. ELEVATION EXISTING DOOR DOOR NUMBER SEE DOOR SCHEDULE INTERIOR SHEET ELEVATION NUMBER DETAIL SHEET NUMBER DETAILS REVISIONS WALL TYPES /SECTIONS ENLARGED I PLANS /DETAILS *(0R) T COLUMNS OR GRID LINES TEMPERED GLASS EXISTING WALL TO REMAIN NEW WALL PER PLAN PLAN SYMBOL LEGEND REVIEWED FOR CODE COMPLIANCE APPROVED JUN 0 4 2010 � a Ci of Tukuwil BUILDING DIVISION CITROFTT A MAY 1.7 2010 PERMIT CENTER Scale: N.T.S. 5- 17 -1.0_ 0 -F- O •0 PERMIT APPLICATION SET C 0 •7) 0 L 10 -068 job no. HC drawn checked 5 -17 -10 date r PREMANUFACTURED CURING OVEN (UNDER SEPARATE PERMIT) / L EXIT F-1 MANUFACTURING AREA & S-1 STORAGE WAREHOUSE EXIT NEW SERVICE SINK. TIE TO EXISTING SEWER LINE CAPPED AT BASE OF COLUMN. MANUFACTURING/ STORAGE (126) NOTE: THIS TENANT WILL NOT USE OR STORE HAZARDOUS MATERIALS BEYOND EXEMPT QUANTITIES ALLOWED PER THE I.B.C. AND I.F.0 PROVIDE 2'-O" RADIUS ON CORNER OF EXISTING WALL OUTUNE OF PREVIOUS RESTROOMS N OFFICE r PREMANUFACTURED PAINT BOOTH (UNDER SEPARATE PERMIT) NEW 8'-0" HIGH CHAINLINK ENCLOSURE WITH (1) 3'-0"x7'-0" C.L. DOOR / LEVER HARDWARE POST SIGN ON CHAIN LINK DOOR FACE "NOT AN EXIT" PROVIDE NEW 3'-0"x7'-0" HOLLOW METAL DOOR AND FRAME PRODUCT FINISH ROOM (123) SECURE STORAGE (121) DATA (122) ... OPEN OFFICE (1 0) TA4.0 EI,X(T X FIELD VERIFY X X MANUFACTURING X (125) X X PROVIDE NEW PAIR 3'-0"x7-0" HOLLOW METAL DOORS AND FRAME IMO Asa --- RELOCATE EXISTING DOOR TO ACCOMMODATE NEW WALL REMOVE EXISTING DOORS AND FRAME AND INFILL EXISTING OPENIN I ALLL EXIST WALL NEW INSULATED WALL TO ALIGN WITH EXISTING WALL REMOVED. INFILL EXISTING OPENING IN WALL AND PROVIDE NEW HOLLOW METAL FRAME— ifi- ',1 FABRIC LAY UP (109) BREAK ROOM REMOVE EXISTI G DOOR AND FRAME AND INFILL EXISTING OPENING. CREATE NEW S-6"x7'-0" OPENING IN EXISTING WALL: NEW COUNTER WITH CABINETS f 'BELOW. .... '''' OFFICE (1 18) MEN LOCKER (117) L _ .. LOCKER (115) WOMEN •\ LOCKER (116) /7- ( NOTE: SCREENED LINE WITH ARROW AT EXIT DOORS DEPICT EGRESS PATH AND DISTANCE FROM • REMOTE POINTS WITHIN OFFICE, WAREHOUSE AND MANUFACTURING SPACE. 75 L.F. ORIGIN POINT DISTANCE OF PATH PATH EXIT POINT FIRST FLOOR PLAN Scale: I/Er...1 '-0" MEN COPY/FAX (114) SEATING (101) OPEN (OFFICE I L —LL / • PANTRY STORAGE (1 08) NEW COUNTERS 14// CABINETS I BELOW AND ABOVE AS SHOWN \ \ \ L .1REQ.EFLIUL _ (100) — OPEgRap WALL. " ROOM (1061 MAIN olONFERENCE STAIR UP r— OFFICE (102) OFFICE (103) EXISTING FULL HEIGHT DEMISING WALL OUTLINE OF EXISTING SECOND FLOOR OFFICE ABOVE 0 Co BREAK ROOM (119) VENDING MACHINES ,PROVIDE POWER, DRAIN AND WATER SUPPLY FOR TENANT SUPPLIED WASHER AND DRYER. FUTURE EMPLOYEE LOCKERS DED. ENLARGED PLAN AT BREAK ROOM Scale: 1 /4"= 1 '-0" COUNTER HEIGHT 'c) -------------- - -------- 2'-0" H11,/ 4'-0" I=1 F. II— T N) T • DED. CNTR. FIGHT. KITCHEN DED. 1O7 ) DW. COUNTER HEIGHT I I I MICROWAVE OUTLET AT UPPER COUNTER HEIGHT MICROWAVE OUTLET AT UPPER [ 6'-7%" 741 I I I lD I _ _. - Co I • • • BREAK ROOM (106) ENLARGED PLAN AT KITCHEN Scale: 1 /4"=r—On EXISTING STAIRS BELOW. END OF CABINET 10" 7 PANTRY STORAGE (1o8 REVIEWED FOR CODE COMPLIANCE APPROVED 'JUN 0 4 2010 16'-6" City of Tukwila BUILDING DIVISION STAIR (104) DN FLOOR EXISTING FIRST i ENTRY/LOBBY. z EXISTING MAIN ENTRY DOORS BELOW. OCCUPANT LOAD FIBERDYNE OPEN OFFICE (THIS AREA) 8 OCCUPANTS 24'-8" + anceifalut MAY 2 1 2010 PERMIT CENTER INCOMPLETE SECOND FLOOR PLAN (EXISTING) (776 S.F. SECOND FLOOR OFFICE AREA) Scale: 1 /8"=1'-0" NOTE: COMPLY EXISTING EMERGENCY EMERGENCY EXIT PATHWAY LIGHTING TO WITH I.B.C. SECTION 1006. (BOTH AND NEW COMPONENTS OF OFFICE EGRESS ILLUMINATION) NOTE: UNDER 1 RACKING WITHIN WAREHOUSE TO BE SEPARATE PERMIT. ,2 I r, ,_ us NOTE: THIS TENANT WILL NOT USE OR STORE HAZARDOUS MATERIALS BEYOND EXEMPT QUANTITIES ALLOWED PER THE I.B.C. AND I.F.0 PROVIDE 2'-O" RADIUS ON CORNER OF EXISTING WALL OUTUNE OF PREVIOUS RESTROOMS N OFFICE r PREMANUFACTURED PAINT BOOTH (UNDER SEPARATE PERMIT) NEW 8'-0" HIGH CHAINLINK ENCLOSURE WITH (1) 3'-0"x7'-0" C.L. DOOR / LEVER HARDWARE POST SIGN ON CHAIN LINK DOOR FACE "NOT AN EXIT" PROVIDE NEW 3'-0"x7'-0" HOLLOW METAL DOOR AND FRAME PRODUCT FINISH ROOM (123) SECURE STORAGE (121) DATA (122) ... OPEN OFFICE (1 0) TA4.0 EI,X(T X FIELD VERIFY X X MANUFACTURING X (125) X X PROVIDE NEW PAIR 3'-0"x7-0" HOLLOW METAL DOORS AND FRAME IMO Asa --- RELOCATE EXISTING DOOR TO ACCOMMODATE NEW WALL REMOVE EXISTING DOORS AND FRAME AND INFILL EXISTING OPENIN I ALLL EXIST WALL NEW INSULATED WALL TO ALIGN WITH EXISTING WALL REMOVED. INFILL EXISTING OPENING IN WALL AND PROVIDE NEW HOLLOW METAL FRAME— ifi- ',1 FABRIC LAY UP (109) BREAK ROOM REMOVE EXISTI G DOOR AND FRAME AND INFILL EXISTING OPENING. CREATE NEW S-6"x7'-0" OPENING IN EXISTING WALL: NEW COUNTER WITH CABINETS f 'BELOW. .... '''' OFFICE (1 18) MEN LOCKER (117) L _ .. LOCKER (115) WOMEN •\ LOCKER (116) /7- ( NOTE: SCREENED LINE WITH ARROW AT EXIT DOORS DEPICT EGRESS PATH AND DISTANCE FROM • REMOTE POINTS WITHIN OFFICE, WAREHOUSE AND MANUFACTURING SPACE. 75 L.F. ORIGIN POINT DISTANCE OF PATH PATH EXIT POINT FIRST FLOOR PLAN Scale: I/Er...1 '-0" MEN COPY/FAX (114) SEATING (101) OPEN (OFFICE I L —LL / • PANTRY STORAGE (1 08) NEW COUNTERS 14// CABINETS I BELOW AND ABOVE AS SHOWN \ \ \ L .1REQ.EFLIUL _ (100) — OPEgRap WALL. " ROOM (1061 MAIN olONFERENCE STAIR UP r— OFFICE (102) OFFICE (103) EXISTING FULL HEIGHT DEMISING WALL OUTLINE OF EXISTING SECOND FLOOR OFFICE ABOVE 0 Co BREAK ROOM (119) VENDING MACHINES ,PROVIDE POWER, DRAIN AND WATER SUPPLY FOR TENANT SUPPLIED WASHER AND DRYER. FUTURE EMPLOYEE LOCKERS DED. ENLARGED PLAN AT BREAK ROOM Scale: 1 /4"= 1 '-0" COUNTER HEIGHT 'c) -------------- - -------- 2'-0" H11,/ 4'-0" I=1 F. II— T N) T • DED. CNTR. FIGHT. KITCHEN DED. 1O7 ) DW. COUNTER HEIGHT I I I MICROWAVE OUTLET AT UPPER COUNTER HEIGHT MICROWAVE OUTLET AT UPPER [ 6'-7%" 741 I I I lD I _ _. - Co I • • • BREAK ROOM (106) ENLARGED PLAN AT KITCHEN Scale: 1 /4"=r—On EXISTING STAIRS BELOW. END OF CABINET 10" 7 PANTRY STORAGE (1o8 REVIEWED FOR CODE COMPLIANCE APPROVED 'JUN 0 4 2010 16'-6" City of Tukwila BUILDING DIVISION STAIR (104) DN FLOOR EXISTING FIRST i ENTRY/LOBBY. z EXISTING MAIN ENTRY DOORS BELOW. OCCUPANT LOAD FIBERDYNE OPEN OFFICE (THIS AREA) 8 OCCUPANTS 24'-8" + anceifalut MAY 2 1 2010 PERMIT CENTER INCOMPLETE SECOND FLOOR PLAN (EXISTING) (776 S.F. SECOND FLOOR OFFICE AREA) Scale: 1 /8"=1'-0" 0 .,— ek — N in ,2 I r, ,_ us OD -I- 0 INCOMPLETE LETTER #1 REVISIONS PERMIT APPLICATION SET 1 revision .- 0 C checked 0 -068 no iwn T r- 0 , I 0 ir) 73 1 KITCHEN 119 NORTH KITCHEN 119 NORTH INTERIOR ELEVATIONS 13 TA2.2 i -7= - KITCHEN 14 TA2.2 XT" 1-- z 4 _ 1`N < X ` ) 6 KITCHEN 119 SOUTH 119 SOUTH L 1-- ^_L -1- _ < X ` = -- -x = - �r - - -� r - -, �� NU, r - = -� - LMICRO1 L IC—R-61 KITCHEN 119 WEST BREAK 119 EAST KITCHEN 119 NORTH INTERIOR ELEVATION KEYNOTES 01 PLASTIC LAMINATE COUNTER TOP W/ 4" P –LAM BACKSPLASH. SEE X/TA2.2 02 PLASTIC LAMINATE CABINET DOORS W/ COUNTER, SINK AND BACKSPLASH ABOVE 03 PLASTIC LAMINATE UPPER CABINET W/ SHELVES ® PLASTIC LAMINATE CABINET W/ DRAWER, SHELF, COUNTER & BACKSPLASH 05 PLASTIC LAMINATE UPPER CABINET W/ MICROWAVE SHELF ® PLASTIC LAMINATE CABINET WITH BANK OF DRAWERS 07 PLASTIC LAMINATE CABINET WITH VERTICAL PAN DIVIDERS ® PLASTIC LAMINATE CABINET WITH ROLL OUT SHELVES. ® 4" RUBBER BASE PER FINISH SCHEDULE. O DISHWASHER (STANDARD OPENING MODEL) Q DISHWASHER (LOW CLEARANCE MODEL) REFRIGERATOR PER TENANT. WASHER & DRYER BY TENANT. CABINETS BEYOND. PLASTIC LAMINATE CABINET W/ HOLE IN COUNTER FOR WASTE & RECYCLE BINS BELOW. NOTES: 1. ALL FIXTURE HEIGHTS AND CLEARANCES TO COMPLY WITH I.B.C. CHAPTER 11, WAC 51 -50 AND ICC /ANSI A117.1 (TYPICAL). 2. CONTRACTOR TO INSTALL ALL BACKING AND BLOCKING AS REQUIRED TO MOUNT FIXTURES. Scale: 1/4 " =1' -0" PLASTIC LAMINATE COUNTER TO OVERHAND 10" AT COUNTER SEATING AREA. CABINET W/ SHELVES Scale: 1"=1 –0" PLASTIC LAMINATE COUNTER TOP ON VERTICAL CABINET 4" WIRE PULL TYP. PLASTIC LAMINATE BASE CABINET W/ 2 ADJUSTABLE SHELVES PROVIDE K &V 255 INLAID PILASTER SHELF STANDARDS & CLIPS. (TYP.) BASE PER FINISH SCHEDULE _ PLASTIC LAMINATE COUNTER 7—TOP ON VERTICAL CABINET 2' -6" a 4" WIRE PULL TYP. PLASTIC LAMINATE BASE CABINET W/ 2 ADJUSTABLE SHELVES PROVIDE K &V 255 INLAID PILASTER SHELF STANDARDS & CLIPS. (TYP.) BASE PER FINISH SCHEDULE CABINET W/ ROLL OUT SHELVES Scale: 1"=1'-0" 0 i M CABINET W/ DRAWERS Scale: 1 " =1' -0" PLASTIC LAMINATE COUNTER TOP W/ 4" BACKSPLASH. TERMINATE BACKSPLASH AT FACE OF COUNTER AT END WALL LOCATIONS. (TYP.) 4" WIRE PULLS (TYP.) PLASTIC LAMINATE BASE CABINET W/ (4) DRAWERS. INTERIOR SURFACES TO BE WHITE MELAMINE. BASE PER FINISH SCHEDULE 2' -1" DRAWER W/ WIRE PULL PLASTIC LAMINATE BASE CABINET W/ 1 ADJUSTABLE SHELF W/ WIRE PULLS BASE PER SCHEDULE CABINET WI DRAWER & SHELF Scale: 1 " =1' -0" 2' –l" PLASTIC LAMINATE BACKSPLASH 0 iV PLASTIC LAMINATE WASTE & RECYCLE BINS BY TENANT 12" DIA. HOLE IN COUNTER TOP FOR WASTE & RECYCLE MATERIAL TO DROP THROUGH TO BINS BELOW. M� DRAWER W/ WIRE PULL PLASTIC LAMINATE BASE CABINET W/ WIRE PULLS BASE PER SCHEDULE CABINET FOR WASTE /RECYCLE Scale: 1 " =1' -0" 13 5/8" Co a 2' -1" PLASTIC LAMINATE UPPER CABINET W/ 2 ADJUSTABLE SHELVES. ALL INTERIOR SURFACES TO BE FINISHED WI WHITE MELAMINE 4" WIRE PULL TYP. PLASTIC LAMINATE BACKSPLASH DRAWER W/ WIRE PULL PLASTIC LAMINATE BASE CABINET W/ 1 ADJUSTABLE SHELF BASE PER SCHEDULE CABINET WI DRAWER & SHELF & UPPERS Scale: 1 " =1' -0" 0 N CO 13 5/8" PLASTIC LAMINATE UPPER CABINET. ALL INTERIOR SURFACES SURFACES TO BE FINISHED W/ WHITE MELAMINE 4" WIRE PULL TYP. PLASTIC LAMINATE MICROWAVE SHELF PLASTIC LAMINATE BACKSPLASH PLASTIC LAMINATE BASE CABINET W/ 1 ADJUSTABLE SHELF BASE PER SCHEDULE CABINET W/ DRAWER & SHELF & UPPERS MICROWAVE SHELF Scale: 1 " =1' -0" a 13 5/8" a \ \ NOTE: PROVIDE BLOCKING AT ALL WALLS TO RECEIVE CABINETS. COORDINATE WITH CABINET MANUFACTURER. (TYP.) –1" PLASTIC LAMINATE UPPER CABINET W/ (2) ADJUSTABLE SHELVES. INTERIOR SURFACES TO BE WHITE MELAMINE. PROVIDE K &V 255 INLAID PILASTER SHELF STANDARDS & CLIPS. 4" WIRE PULL (TYP.) SINK PER MECH DRAWINGS PROVIDE GOOSE NECK FAUCET PLASTIC LAMINATE COUNTER TOP W/ 6" BACKSPLASH WHERE COUNTER DROPS FOR SINK BASE. FALSE DRAWER FRONT 4" WIRE PULL (TYP.) PROVIDE HEAT SHIELD ON ALL EXPOSED PIPE. UNDER COUNTER AREA CLEAR FOR WHEELCHAIR ACCESS. BASE PER FINISH SCHEDULE CABINET WI SINK & UPPERS Scale: 1 " =1' -0" 13 5/8" td- 2' -1" PLASTIC LAMINATE UPPER CABINET W/ 2 ADJUSTABLE SHELVES. ALL INTERIOR SURFACES TO BE FINISHED W/ WHITE MELAMINE 4" WIRE PULL TYP. PLASTIC LAMINATE BACKSPLASH d- DRAWER PULL W/ WIRE PLASTIC LAMINATE BASE CABINET W/ 1 ADJUSTABLE SHELF W/ WIRE PULLS BASE PER SCHEDULE CABINET WI DRAWER & SHELF & UPPERS Scale: 1 " =1' -0" REVIEWED FOR CODE COMPLIANCE APPROVED JUN 042010 City of Tukwila BUILDING fIVISIflnI GITY OMLA MAY 17 2010 PERMIT CENTER C6) 715' -0" 60' -0" 60' —O" MANUFACTURING/ STORAGE (126) NEW EMERGENCY EXIT SIGNS WITH BATTERY BACK —UP PATHWAY UGHTS. SUSPENDED FROM CEILING TO 10' -0" X MANUFACTURING X ( 1 1 1] IWO i PRODO FINISH , ROOM \\J SECURE ;STORAG L--- / (121) / BREAK ROAM (11 9) NEW SUSPENDED �... CEILING AND%GRID TO - MAT1H-EXIST • / RELOCATED LAY —IN - =. LIGHT /FIXTURES Ff 6M DgMOLITION WORK <. s 5 .,A iaoaoco949 d 4 FABRIC LAY UP 1(R1 co N OP PANTRY . MEN LOCKE 1 I I I I I I I L N.onianv7iv EXISTING LAY —I FIXTURES T& RELOCATED ( HOWS NEW FLOOR PLAN (AREA UNDER THIS PERMIT) SEATING MI) OPEN SECO CEIU A NO OR EIU CH NGE T S PERMIT. LIGHT ROW OCA(fION) ST ROOMI MAIN FEREN (1 -05) NON J 04 LOOR OVE. TION i-� �A CD N CD a 0 CO CEILING INSULATION PER WALL SECTION 7/8" TENT LIGHT FIXTURE W/ CEIUNG TILES FOR INSULATION COVER, SIMILAR TO UL DESIGN G216. 4" SUSP. ACOUSTIC. TILE CEILING AND GRID SYSTEM PER REFLECTED CEILING PLAN 2 X4 RECESSED FLUORESCENT LIGHT FIXTURE PER REFLECTED CEILING PLAN FIXTURE TENT AT SUSP. CEILING Scale: 1 1/2"=V-0" IF HANGER WIRE IS OUT OF PLUMB GREATER THAN 1:6 COUNTER SPLAY PER ASTM C636 WALL WHICH PENETRATES CEILING GRID WALL EDGE MOLDING i 1 MAX. 8" MIN. 3/4" MIN. 2" UN— ATTACHED WALLS EDGE TRACK AT SUSP. CEILING #12 PERIMETER HANGER WIRE ANCHORED TO STRUCTURE ABOVE ® EACH MAIN BEAM OR CROSS TEE STABILIZER BAR SYSTEM TO KEEP PERIMETER COMPONENTS FROM SPREADING APART ® UNATTACHED WALLS ONLY TIGHT LOOP THROUGH HANGER HOLE & THREE TIGHT TURNS WITHIN 3" ( TOP TO BOTTOM) PER ASTM C636 MAIN BEAM OR CROSS TEE CEILING GRID Scale: 3 " =1' -0" #12 HANGER WIRE ANCHORED TO STRUCTURE ABOVE EXPANSION JOINT PER CEILING MANUF. EXPANSION JOINT AT SUSP. CEIUNG Scale: 3 " =1' -0" CEILING / ucHmNc SYM �1 LS & LEGEND EXISTING SUSPENDED ACOUSTICAL TILE CEILING NEW 2' X 4' SUSPENDED ACOUSTICAL TILE CEILING EXISTING COMPACT FLUORESCENT LIGHT FIXTURE EXISTING 2' X 2' FLUORESCENT LIGHT EXISTING 2' X 4' FLUORESCENT LIGHT EXISTING 2' X 4' FLUORESCENT LIGHT TO BE RELOCATED EXISTING 2' X 4' FLUORESCENT LIGHT TO BE RELOCATED EXISTING 2' X 4' FLUORESCENT LIGHT WITH BATTERY BACK —UP (NIGHTIME /PATHWAY LIGHTING) EXISTING LIGHTED EXIT SIGN Scale: 1/8"=V-0" STEEL STUD COMPRESSION POST AS REQUIRED BY BUILDING OFFICIAL #12 HANGER WIRE TYP. TIGHT LOOP THROUGH HANGER HOLE & THREE TIGHT TURNS WITHIN 3" ( TOP TO BOTTOM) CROSS TEE MAIN CEILING PER ASTM C635 BEAM PER ASTM C635 CEILING INSTALLATION REQUIREMENTS • SUSPENDED CEILINGS SHALL BE BRACED AGAINST LATERAL MOVEMENT DUE TO EARTHQUAKE PER ASTM C636. IN THE ABSENCE OF AN ENGINEERED DESIGN THE FOLLOWING BRACING SYSTEM WILL BE REQUIRED. FOUR NO. 12 GA STEEL WIRES SHALL BE ATTACHED TO A MAIN RUNNER WITHIN 2 INCHES OF A CROSS RUNNER. THE WIRES SHALL BE SPLAYED 90 DEGREES TO EACH OTHER AND RUN UP TO STRUCTURE ABOVE AT AN ANGLE NOT TO EXCEED 45 DEGREES FROM THE HORIZONTAL. A COMPRESSION STRUT SHALL EXTEND FROM THE MAIN RUNNER AT THE ATTACHMENT OF THE WIRES VERTICALLY AND BE ATTACHED TO THE STRUCTURE ABOVE AS REQUIRED BY BUILDING OFFICIAL SUCH BRACING SYSTEMS SHALL BE PROVIDED AT A SPACING NOT TO EXCEED 12 FEET IN BOTH DIRECTIONS. BEGINNING AT A POINT NOT TO EXCEED 6 FEET FROM WALLS. VERTICAL AND PERIMETER HANGERS INSTALLED PER ASTM C636 AND MANUFACTURERS REQUIREMENTS. LIGHTING FIXTURES WHICH WEIGH LESS THAN 56 POUNDS SHALL BE ATTACHED TO THE CEILING GRID SYSTEM AND TO BUILDING STRUCTURE BY AT LEAST 2 NO. 12 GAGE WIRES. LIGHT FIXTURES WHICH WEIGH 56 POUNDS OR MORE SHALL BE SUSPENDED FROM THE STRUCTURE INDEPENDENT OF THE CEILING GRID, AND AN ENGINEERING DESIGN SHALL BE SUBMITTED TO SUBSTANTIATE THE SUSPENSION SYSTEM. MECHANICAL EQUIPMENT SHALL BE SUPPORTED INDEPENDENT OF THE CEILING SUSPENSION SYSTEM. • MINIMUM 2" WIDE WALL MOLDING • GRID MUST BE ATTACHED TO TWO ADJACENT WALLS — OPPOSITE WALL MUST HAVE A 3/4" CLEARANCE. • ENDS OF MAIN BEAMS AND CROSS TEES MUST BE TIED TOGETHER TO PREVENT THEIR SPREADING. • PERIMETER SUPPORT WIRES MUST BE WITHIN 8" OF CEILING EDGE. • PROVIDE MANUFACTURERS HEAVY DUTY GRID SYSTEM. • CEILING AREAS OVER 1,000 SF MUST HAVE HORIZONTAL RESTRAINT WIRE OR RIGID BRACING. • CEILING AREAS OVER 2,500 SF MUST HAVE MUST HAVE SEISMIC SEPARATION JOINTS OR FULL HEIGHT PARTITIONS. • CEILINGS WITHOUT RIGID BRACING MUST HAVE 2" OVERSIZED TRIM RINGS FOR SPRINKLERS AND OTHER PENETRATIONS. • CHANGES IN CEILING PLANE MUST HAVE POSITIVE BRACING. • CABLE TRAYS AND ELECTRICAL CONDUITS MUST BE INDEPENDENTLY SUPPORTED AND BRACED. SUSPENDED CEILING WILL BE SUBJECT TO SPECIAL INSPECTION AS REQUIRED BY LOCAL BUILDING OFFICIAL • IF CEILING SYSTEM TO BE INSTALLED IS NOT AS SPECIFIED ABOVE, CONTRACTOR SHALL SUBMIT ALTERNATIVE MATERIAL AND METHODS AS DESCRIBED IN I.B.C. SECTION 104.11 TO LOCAL BUILDING OFFICIAL. SEISMIC BRACE AT SUSPENDED CEILING N.T.S. WALL EDGE MOLDING CROSS TEE PER ASTM C635 SUSP CEILING BRACE AT PERIMETER STABILIZER BAR SYSTEM TO KEEP PERIMETER COMPONENTS FROM SPREADING APART 0 UNATTACHED WALLS ONLY REVIEWED FOR CODE COMPLIANCE APPROVED JUN 0 4 2010 City of Tukwila B UILDING DIVISION cmr��LA MAY 21 2010 PERMIT CENTER N.T.S. 00 I or•-• N I)113 I i INCOMPLETE LETTER #1 REVISIONS PERMIT APPLICATION SET revision ,— O CO C 0 o -13 - 0 HC drawn checked 0 I m 7 41-3 3' -0" X 7' -0" HOLLOW METAL DOOR WI H.M. FRAME W/ 7 "x37" TEMPERED GLASS LITE IN MTL. FRAME DOOR TYPES Scale: 1/4"=V-0" 5/8" TYPE 'X' GWB EACH SIDE OVER METAL STUDS ® 24" O.C. SEE WALL TYPE PAIR 3' -0" X 7' -0" HOLLOW METAL DOORS W/ H.M. FRAME W/ 7 "x37" TEMPERED GLASS LITE IN MTL. FRAME W /BLACK KICKPLATES. (EACH SIDE) PAINTED H.M. FRAME TYP. SILENCERS STRIKE SIDE INSULATION PER WALL TYPE. DOOR AS SCHEDULED HOLLOW METAL DOOR JAMB /HEAD Scale: 3' =1' -0" WALL AT PERIMETER R -25 BATT INSULATION OVER NEW OPEN OFFICE AREA SUSPENDED CEILING SYSTEM PER REFLECTED CEILING PLAN 6" X 20 GA. METAL STUDS ® 24" O.C. WITH 5/8" TYPE "X" GWB EACH SIDE (PAINT OPEN OFFICE SIDE ONLY) R -21 BATT INSULATION AT INTERIOR PERIMETER WALLS 1/8" DIA. X 1" POWDER ACTUATED FASTENERS 24" O.C. BASE PER SCHEDULE EXIST. CONC. FLOOR SLAB Scale: 1/2"=V-0" ' -0" 3' -0" X 7' -0" X r TEMP. GLASS DOOR W/ 1 DIA. X 12' PULL AND 30" PUSH BAR. STEEL PLATES EACH SIDE FOR MOUNTING LEVER HARDWARE 3' -0" x 7' -8" CHAIN LINK DOOR DOOR & WINDOW NOTES 1. ALL DOOR HARDWARE TO COMPLY WITH I.B.C. SECTION 1008, WAC 51 -50 AND A.D.A. 2. PROVIDE INTERNATIONAL SYMBOL OF ACCESS SIGNAGE AT EACH ACCESSIBLE ENTRANCE DOOR. (MAIN ENTRANCE AND EMPLOYEE ENTRANCE) 3. ALL EXIT DOORS SHALL BE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR ANY SPECIAL KNOWLEDGE OR EFFORT PER I.B.C. SECTION 1008.1.8 4. PROVIDE SAFETY GLAZING PER DRAWINGS AND I.B.C. SECTION 2406. T= TEMPERED GLAZING. DOOR SCHEDULE DOOR NO. T DESCRIPTION DOOR FRAME HARDWARE GROUP ;i in REMARKS Co to FIN. MAT. PAIR 3' -0" X 7' -0" HOLLOW METAL DOORS W/ H.M. FRAME W/ 7 "x37" TEMPERED GLASS LITE IN MTL. FRAME W /BLACK KICKPLATES. (EACH SIDE) PAINTED H.M. FRAME TYP. SILENCERS STRIKE SIDE INSULATION PER WALL TYPE. DOOR AS SCHEDULED HOLLOW METAL DOOR JAMB /HEAD Scale: 3' =1' -0" WALL AT PERIMETER R -25 BATT INSULATION OVER NEW OPEN OFFICE AREA SUSPENDED CEILING SYSTEM PER REFLECTED CEILING PLAN 6" X 20 GA. METAL STUDS ® 24" O.C. WITH 5/8" TYPE "X" GWB EACH SIDE (PAINT OPEN OFFICE SIDE ONLY) R -21 BATT INSULATION AT INTERIOR PERIMETER WALLS 1/8" DIA. X 1" POWDER ACTUATED FASTENERS 24" O.C. BASE PER SCHEDULE EXIST. CONC. FLOOR SLAB Scale: 1/2"=V-0" ' -0" 3' -0" X 7' -0" X r TEMP. GLASS DOOR W/ 1 DIA. X 12' PULL AND 30" PUSH BAR. STEEL PLATES EACH SIDE FOR MOUNTING LEVER HARDWARE 3' -0" x 7' -8" CHAIN LINK DOOR DOOR & WINDOW NOTES 1. ALL DOOR HARDWARE TO COMPLY WITH I.B.C. SECTION 1008, WAC 51 -50 AND A.D.A. 2. PROVIDE INTERNATIONAL SYMBOL OF ACCESS SIGNAGE AT EACH ACCESSIBLE ENTRANCE DOOR. (MAIN ENTRANCE AND EMPLOYEE ENTRANCE) 3. ALL EXIT DOORS SHALL BE OPENABLE FROM THE INSIDE WITHOUT THE USE OF A KEY OR ANY SPECIAL KNOWLEDGE OR EFFORT PER I.B.C. SECTION 1008.1.8 4. PROVIDE SAFETY GLAZING PER DRAWINGS AND I.B.C. SECTION 2406. T= TEMPERED GLAZING. DOOR SCHEDULE DOOR NO. T DESCRIPTION DOOR FRAME HARDWARE GROUP RATING REMARKS MAT. FIN. MAT. FIN. 106 C 3'- 0 "x7' -0" GLASS FACT. - — - — 109A A 3'- 0 "x7' -0" HM PAINT HM PAINT — — O ir m /} o 109B A 3'-0"x7'-0" HM PAINT HM PAINT — — 109C B PAIR 3'- 0 "x7' -0" HM PAINT HM PAINT 110 A 3'- 0 "x7' -0" HM PAINT HM PAINT , — — 125 D 3'- 0 "x7' -8" CHAINLINK GALV. STEEL GALV. — - DOORS DESIGNATED "E" ON PLAN ARE EXISTING WITH NO CHANGE PER THIS PERMIT. HALLWAY 132 EXISTING JAMB AT O.H. DOOR NEW 2x BLOCKING AS REQUIRED FENCE POST WITH BASE PLATE. SEE 8/TA4.0. — EXISTING O.H. DOOR TRACK USE 8" OR LARGER METAL STUD AT HALLWAY WALL TERMINATION ADJACENT TO EXISTING OVERHEAD DOOR TRACK. (WALL TO BE HELD AS TIGHT TO TRACK AS POSSIBLE WITHOUT HINDERING DOOR USE.) WALL AT EXISTING O.H. DOOR JAMB Scale: 3' =1' -0" POSTS AT 10' -0" MAX. OR AS FOR 8 -0" HIGH ENCLOSURE HORIZONTAL TOP & BOTTOM RAIL TYPICAL WELD P CONCRETE SLAB GALV. STEEL BASE PLATE WI ANCHOR BOLTS TO EXISTING SLAB. o LLI J Li EXISTING OPENING TO BE R -25 BATT INSULATION OVER ENTIRE NEW CEILING AREA. - CEILING PER REFLECTED CEILING PLAN SOUND BATT INSULATION 3 5/8" X 20 GA. METAL STUDS 0 24" O.C. WITH 5/8" TYPE "X" GWB EACH SIDE. (PAINT), STAGGER STUDS WHERE WALL TO BE INFILLED IS GREATER THAN 4 74". 1/8" DIA. X 1" POWDER ACTUATED FASTENERS 0 24" O.C. BASE PER SCHEDULE - EXIST. CONC. FLOOR SLAB WALL INFILL AT EXISTING WALL Scale: 1/2 " =1' -0' FENCE BASE PLATE Scale: 3' =1' -0" DOOR SCHEDULES 8' -0" HIGH CHAIN - LINK ENCLOSURE PER PLAN. REVIEWED FOR CODE COMPLIANCE APPROVED JUN 0 4 2010 City Ci of Tukwila BUILDING DIVISION RECELVED CITY OF TUKWILA MAY 21 2010 PERMIT CENTER I d 0 Li � W W OZ m 1- CC z z m ILL N - J W z c J W W 0 0 0 d M N N M c0 0 N r, w H w o SEATTLE 2 0 re Q 130 LAKES sheet TA4.O 5 -20 -10 5 -17 -10 0 0 INCOMPLETE LETTER #1 REVISIONS PERMIT APPLICATION SET C 0 m L r- C 10 -068 job no. HC drawn checked O ir m /} o I d 0 Li � W W OZ m 1- CC z z m ILL N - J W z c J W W 0 0 0 d M N N M c0 0 N r, w H w o SEATTLE 2 0 re Q 130 LAKES sheet TA4.O