Loading...
HomeMy WebLinkAboutPermit D11-079 - SKARBOS - REROOFSKARBOS (FORMERLY) 345 ANDOVER PK E Dl 1 -079 City ofTukwila • Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone : 206-431-3670 Fax: 206 - 431 -3665 Web site: http: / /www.ci.tukwila.wa.us Parcel No.: 0223400040 Address: 345 ANDOVER PK E TUKW Suite No: Project Name: SKARBOS (FORMERLY) DEVELOPMENT PERMIT Permit Number: D11 -079 Issue Date: 04/18/2011 Permit Expires On: 10/15/2011 Owner: Name: SRO PROPERTIES INC Address: 1411 4TH AVE #1315 , SEATTLE WA 98101 Contact Person: Name: PEARLLA KAESTNER Address: PO BOX 82894 , KENMORE WA 98028 Contractor: Name: ASSOCIATED ROOFING INC Address: PO BOX 82894 , KENMORE, WA 98028 Contractor License No: ASSOCRI16206 Phone: 206 364 -4445 Phone: Expiration Date: 05/06/2012 DESCRIPTION OF WORK: REROOF: INSTALLATION OF A GRANULAR SURFACED MODIFIED BITUMEN ROOF SYSTEM. MATERIALS ARE POLYGLASS POLYFLEX G. Value of Construction: $29,955.00 Type of Fire Protection: Type of Construction: Electrical Service Provided by: Fees Collected: $1,092.10 International Building Code Edition: 2009 Occupancy per IBC: 0019 * *continued on next page ** doc: IBC -7/10 D11-079 Printed: 04 -18 -2011 • • Public Works Activities: Channelization / Striping: N Curb Cut / Access / Sidewalk / CSS: N Fire Loop Hydrant: Flood Control Zone: Hauling: Land Altering: Landscape Irrigation: Moving Oversize Load: N N Number: 0 Size (Inches): 0 Start Time: Volumes: Cut 0 c.y. End Time: Fill 0 c.y. Start Time: End Time: Sanitary Side Sewer: Sewer Main Extension: Private: Public: Storm Drainage: Street Use: Profit: N Non- Profit: N Water Main Extension: Private: Public: Water Meter: N Permit Center Authorized Signature: Date: ( 9—' b I hereby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances governing this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating construction qF the performance of work. I am authorized to sign and obtain this development permit and agree to the conditions attached to this permit Signature: Print Name: Date: z/--/e-/( This permit shall become null an void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. PERMIT CONDITIONS: 1: ** *BUILDING DEPARTMENT CONDITIONS * ** 2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the Building Official. 3: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to start of any construction. These documents shall be maintained and made available until final inspection approval is granted. 4: All construction shall be done in conformance with the approved plans and the requirements of the International Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code. 5: Manufacturers installation instructions shall be available on the job site at the time of inspection. 6: Remove all demolition rubble and loose miscellaneous material from lot or parcel of ground, properly cap the sanitary sewer connections, and properly fill or otherwise protect all basements, cellars, septic tanks, wells, and other excavations. Final inspection approval will be determined by the building inspector based on satisfactory completion of this requirement. doc: IBC -7/10 D11 -079 Printed: 04 -18 -2011 7: Prior to final inspection for this building Oit, a copy of the roof membrane manufactuwarranty certificate shall be provided to the building inspector. 8: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the Building Official from requiring the correction of errors in the construction documents and other data. doc: IBC -7/10 D11 -079 Printed: 04 -18 -2011 CITY OF TUKILA Community Development Department Public Works Department Permit Center 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 http://www. ci. tukwila. wa. us Building Permit No. I) 1 I 011 Mechanical Permit No. Plumbing/Gas Permit No. Public Works Permit No. Project No. (For office use only) Applications and plans must be complete in order to be accepted for plan review. Applications will not be accepted through the mail or by fax. * *Please Print ** SITE LOCATION Site Address: S /gAJDO -o5A Pl. E King Co Assessor's Tax No.: (Y12 340- O O c/ o c)eeaL bl� . ((``,�,, Suite Number: Floor: A it Tenant Name: —iV Vint r S+c�.rbo S. j � New Tenant: ❑ Yes a ❑ ..No Property Owners Name: SRO PrOPerc c.S JA rat s edit f ° `etie- ZOO - 7 3 93 Mailing Address: / VII rex t %44') Ave, db./3/S .5enlille1 9 8'/ � City State Zip CONTACT PERSON — who do we contact when your permit is ready to be issued Name: P64 RUA ` )He- s�7ei ! /3i i**'d ay Tele hone: (� `?t2 «- VI Mailing Address: 4' ez pz q41 Af)Yic/Le. (n '3.j 2' City State Zip gi6cfe74-'rlci/Z©6r f4C. x Number: 02.06 3 f,i ff 303 E -Mail Address: GENERAL CONTRACTOR INFORMATION — (Contractor Information for Mechanical (pg 4) for Plumbing and Gas Piping (pg 5)) Company Name: 5.540C-/ L) Mailing Address: 0. &X i 2 Contact Person: �r !►'l E -Mail Address: Contractor Registration Number: 5502f l(vzD, tr ( State Zip Day Telephone: 2e —36 171q F ax Number: c:2- Lo � 4' 3° 3 S� Expiration Date: 17)/14-Y a0 , .2t) ( L ARCHITECT OF RECORD — All plans must be stamped by Architect of Record Company Name: Mailing Address: City State Zip Contact Person: Day Telephone: E -Mail Address: Fax Number: ENGINEER OF RECORD — All plans must be stamped by Engineer of Record Company Name: [ Mailing Address: Address: City State Zip Contact Person: Day Telephone: E -Mail Address: Fax Number: H:\Applications\Fonm.Applications On tine\20I0 Applications \7 -2010 - Permit Application.doc Revised: 7 -2010 bh Page 1 of 6 BUILDING PERMIT INFORMATI(Ar 206 -431 -3670 Valuation of Project (contractor's bid price): $ 27, • Existing Building Valuation: $ (.I►1�U,l CIJ Scope of Wor (please provide detailed in onnation): S/C% /�- ,) o� /3 6g�Nu kr- it lea fled, red _ rnar r L .moo-/ J do a � ss o L f 4 C e C y x Will there be new rack storage? ❑ Yes 'QQ.. No If yes, a separate permit and plan submittal will be required. Provide All Building Areas in Square Footage Below PLANNING DIVISION: Single family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches) 'For an Accessory dwelling, provide the following: Lot Area (sq ft): Floor area of principal dwelling: Floor area of accessory dwelling: *Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence. Number of Parking Stalls Provided: Standard: Will there be a change in use? ❑ Yes FIRE PROTECTION/HAZARDOUS MATERIALS: Sprinklers ❑ Automatic Fire Alarm Compact: Handicap: No If `yes ", explain: ❑ None ❑ Other (specify) Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ Yes i'4 No If `yes', attach list of materials and storage locations on a separate 8 -1/2 "x 11 " paper including quantities and Material Safi 4 a Sheets. SEPTIC SYSTEM ❑ On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health Department. H:Wpplications\Fonns- Applications On Line\2010 Applications \7 -2010 - Permit Application.doc Revised: 7 -2010 hh Page 2 of 6 Existing Interior Remodel Addition to Existing Structure New Type of Construction per IBC Type of Occupancy per IBC lst Floor V6 A AA 2"d Floor 3`d Floor Floors thru Basement Accessory Structure* Attached Garage Detached Garage Attached Carport Detached Carport Covered Deck Uncovered Deck PLANNING DIVISION: Single family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches) 'For an Accessory dwelling, provide the following: Lot Area (sq ft): Floor area of principal dwelling: Floor area of accessory dwelling: *Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence. Number of Parking Stalls Provided: Standard: Will there be a change in use? ❑ Yes FIRE PROTECTION/HAZARDOUS MATERIALS: Sprinklers ❑ Automatic Fire Alarm Compact: Handicap: No If `yes ", explain: ❑ None ❑ Other (specify) Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ Yes i'4 No If `yes', attach list of materials and storage locations on a separate 8 -1/2 "x 11 " paper including quantities and Material Safi 4 a Sheets. SEPTIC SYSTEM ❑ On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health Department. H:Wpplications\Fonns- Applications On Line\2010 Applications \7 -2010 - Permit Application.doc Revised: 7 -2010 hh Page 2 of 6 PERMIT APPLICATION NOTES — Applicable to all permits in this application Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject to possible revision by the Permit Center to comply with current fee schedules. Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation. Building and Mechanical Permit The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be requested in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition). Plumbing Permit The Building Official may grant one extension of time for an additional period not exceeding 180 days. The extension shall be requested in writing and justifiable cause demonstrated. Section 103.4.3 Uniform Plumbing Code (current edition). I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING `�N�E R OR AUTHORIZED AGENT: Signature: .r Wr— S h'le,ll Print Name: P„��tY cLes Mailing Address: Date: 3 D :. Telephone: dg' ity IDate Application Accepted: Date Application Expires: H:\Applications\Porms- Applications On Line \2010 Applications \7 -2010 - Permit Appiication.doc Revised: 7 -2010 bh State Staff Initials: ^ ji Page 6 of 6 1 • 4„„ City of Tukwila De P artment of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: http. / /www.ci.tukwila.wa.us RECEIPT Parcel No.: 0223400040 Permit Number: D11-079 Address: 345 ANDOVER PK E TUKW Status: APPROVED Suite No: Applied Date: 03/28/2011 Applicant: SKARBOS (FORMERLY) Issue Date: Receipt No.: R11 -00744 Initials: User ID: WER 1655 Payment Amount: $663.65 Payment Date: 04/18/2011 11:35 AM Balance: $0.00 Payee: ASSOCIATED ROOFING INC TRANSACTION LIST: Type Method Descriptio Amount Payment Check 92013 663.65 Authorization No. ACCOUNT ITEM LIST: Description Account Code Current Pmts BUILDING - NONRES STATE BUILDING SURCHARGE 000.322.100 659.15 640.237.114 4.50 Total: $663.65 doc: Receipt -06 Printed: 04 -18 -2011 r 0 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206 - 431 -3665 Web site: htqx//www.ci.tukwila.wa.us Parcel No.: 0223400040 Address: 345 ANDOVER PK E TUKW Suite No: Applicant: SKARBOS (FORMERLY) RECEIPT Permit Number: D11 -079 Status: PENDING Applied Date: 03/28/2011 Issue Date: Receipt No.: R11 -00590 Initials: User ID: JEM 1165 Payment Amount: $428.45 Payment Date: 03/28/2011 11:07 AM Balance: $663.65 Payee: ASSOCIATED ROOFING INC. TRANSACTION LIST: Type Method Descriptio Amount Payment Check 91904 428.45 Authorization No. ACCOUNT ITEM LIST: Description Account Code Current Pmts PLAN CHECK - NONRES 000.345.830 428.45 Total: $428.45 doc: Receipt -06 Printed: 03 -28 -2011 t t t t • INSPECTION NO. INSPECTION RECORD Retain a copy with permit • PERMIT CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 Permit Inspection Request Line (206) 431 -2451 (206) 431 -3670 Project: ,S' /c /9 / ?%345 Type of Inspection: R�A//9 L Ain Address: if Date Called: Special Instructions: ...1/;•14 _.-- /U . / 5 73° Date Wanted:. a.m: Requester: .206-' 786— 7?C6 Phone No: a06 36 q -4/y`,/,5 Approved per applicable codes. 1 Corrections required prior to approval. COMMENTS: - Ain if 73° f*".49 i -/ /" ;r1/i7 l O Nt /J /C7',- 4_-;,...,- ... .. .... , r ctor: 4,-.0 / SPECTION FEE R' \ UIRED. P,r to next inspection. fee must be id at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Date: /O —24,—// -4:;r4:::463Wril.V433041e., iitar46W.AWSWTZ INSPECTION RECORD I Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 Permit Inspection Request Line (206) 431-2451 (206) 431-367 0 II - 071 Project: Type ofInspection;„ iii-44 M\ C■04:1:1 DA) oA v,fitkiCi-r , mst- k*JE •m-A-AC, Address: 34S AAfoo■Itcr t. Date Called: Special Instructions: 04 "j v34 - d( * 6/./t-\ii (AI(. 0A1/(0 .;, 1 I A. ILI Date Want d: - e '4 2 6---1 f 'frffi7 Requester: Phone No 2,6 6 --S-1 6 1 -- (0.- 1 I 2_ Approved per applicable codes. 1:1Corrections required prior to approval. COMMENTS: iii-44 M\ C■04:1:1 DA) oA v,fitkiCi-r , mst- k*JE •m-A-AC, Inspec or: Date: 4 _24 1/ • r7 REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. Q VATirPr00TUO L7[n1111.111a UL&UI RUULY1 .v // -a"7 9 12 Year Material & Labor Warranty NPR/NDL Owner's Name: Janus Stratton, Stratton Interests Owner's Address: 1411 4th Ave., #1315 City: Seattle State: WA Zip: 98101 Building Name: Former Skarbo's Bldg. Building Address: 345 Andover Pant E City: Tukwila State: WA Zip: 98188 Roofing Contractor Name: Associated Roofing Polyglass Registered Contractors #1684 Roofing Contractor Address: PO BOX 82894 City. Kenmore Roofing Contractor Phone: 206 364 4445 Polyglass Product(s) Used: POLYFLEX G Project Size: 15600SFT Roofing Specification Used: 200 -W-APP -TOR Completion Date: MAY 10, 2011 TERMS AND CONDITIONS: 1. Definitions: ' Polyglass' shall mean Polyglass, 150 Lyon Drive, Fernley, Nevada 89408. 'OWNER' shall mean owner whose name appears on page 1 hereof, upon whose building the roofing membrane was installed. 2. General Provisions: a) Except as otherwise stated herein, Polyglass warrants the roofing membrane against manufacturing defects in the product resulting in leakage for a TWELVE (12) year period from the installation completion date as indicated above, exduding installation. B) No representative of Polyglass has the authority to make any representations or promises except as stated herein. C) The original installation of the roofing membrane must be free of errors, omissions, or poorfimproper workmanship by the roofing contractor and must be installed in accordance with Polyglass' current published specifications in order for this warranty to be effective. 3. Term of Warranty: Except as indicated in paragraphs 7, 8 and 12 hereof, this warranty is valid for TWELVE (12) Years from the date of - completion as indicated above. 4. Notice: Polyglass shall have no obligation under this warranty unless Owner shall have promptly notified Polyglass in written notice along with Proof of Purchase by registered/certified mail of any leak within fifteen (15) days after discovery of the leak to Polyglass USA, Ind. 821 Snively Avenue, Winter Haven, Florida 33880 ATTN: Warranty Department, in order for this warranty to be effective. 5. Claims/Replacement Costs: Polyglass, through its authorized representative, shall make an inspection of the root If, after Inspection, Polyglass, at its sole disaetion, determines that the leakage is the result of faulty material manufactured by Polyglass, then Polyglass shall provide all primary materials and the established neragsary and reasonable labor to replace It, with no limit or proration, at no charge to owner, excluding accessories and other products not manufactured by Polyglass. 6. Exclusions: This warranty will not apply if damage is the direct or indirect result of a) acts of God or natural causes such as, but not limited, lightning, hail, gale force or other strong winds in excess of 8 on the Beaufort Scale, floods, hurricanes, tomadoes, wind launched debris or earthquakes; b) fire; c) accidents; d) vandalism; e) negligence, misuse, or failure of owner to provide reasonable maintenance to the roof, f) structural defects or other excessive building movement g) lack of positive drainage; h) application to the roofing of solvents and petroleum distillates such as but not limited to Xylene, Tolulene, or gasoline; f) disregard of manufacturer's handling procedures with respect to storing, handling and installing of roofing membrane; j) distortion, expansion or contraction of any covered flashing or metal work; k) infiltration or condensation of moisture through or around the walls, coping, hardware or equipment, building structure or underlayment or surrounding materials; I) traffic or storage of materials upon the roof, m) damage to the roofing membrane caused by installation of a.spnnkler system, water or air auditioning equipment, radio or television antenna, frame work for signs, water tower Or other installation on the roof after the installation of the roofing membrane without prior written approval of Polyglass; n) poor workmanship by the roofing contractor, o) inadequate performance of products not manufactured by Polyglass, induding but not limited to metal work, mechanical attachments and adhesives; p) tie -ins to existing roof systems; q) environmental contaminates; r) contractors installation; s) Damage or injury arising in any way from an actual or alleged discharge or release of any pollutant or waste; t)Damage or injury arising in any way from testing or consulting errors or omissions. State: WA Zip: 98028 ECEWWE - LJii BWLDIING DEPARTMENT 7. Cancellation of Warranty. This limited warranty shag become null and void if the submitted warranty information is incomplete and/or the following work is performed without prior written approval of Polyglass: a) any alterations or repairs to the roof, except as authorized by Polyglass; b) subsequent work on or through the root c) changes in building usage; d) abuse, neglect, improper maintenance by owner or his representative; e) any and all court, Ming, or attomeys fees. 8. Access to the Root Owner shag provide free access to the roof and related premises to an authorized representative of Polyglass during the term of this warranty. Owner shall bear this expense of removing and replacing any traffic surfaces or other appurtenances built over the roof if removal is necessary to investigate or repair any claim regarding the roofing membrane. Refusal of access shag result in the voiding of all warranties. Polyglass retains the right to make core extractions and properly repair such extractions. The expenses for extractions are to be paid by Polyglass. 9. Commencement of Warranty This warranty shall not become effective, nor will Polyglass have any obligation under this warranty until all monetary amounts for materials and services related to this installation, inspections, _warranty fees, or claims are paid in fug by OWNER. 10. Waiver. Polyglass' failure at any time to enforce any conditions stated herein shall not be construed as a waiver of any provision of this warranty. 11. Assignment of Warranty: This warranty may be assigned by owner to a successive party provided a) owner shag notify Polyglass in writing of the new party's name and address and b) owner pays a transfer fee of $250 plus any out-of-pocket cost for travel, lodging meals determined necessary by Polyglass to reinspect roof poor to transfer. Upon receipt of the foregoing, Polyglass will advise owner within thirty (30) days of its approval of such proposed reassignment 12. Additional Repairs: In the event repairs are required which are not covered by this warranty, Polyglass will advise OWNER of such repairs to be made at owner's expense. If the required repairs are promptly made by OWNER, this warranty shall remain in effect for the unexpired portion of the original term. If OWNER does not make the required repairs promptly, this warranty shall be automatically terminated without further notice from Polyglass. 13. Installer must be a Polyglass Registered Contractor. THIS WARRANTY SUPERCEDES AND IS IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY SHALL BE OWNER'S EXCLUSIVE REMEDY AGAINST POLYGLASS OR ITS AFFILIATES WITH RESPECT TO THE ROOF, AND NEITHER POLYGLASS OR ITS AFFILIATES SHALL BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES. POLYGLASS' AGENTS HAVE NO AUTHORITY TO GIVE WARRANTIES BEYOND THOSE PROVIDED IN THIS WARRANTY. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitation or exclusion may not apply to you. This warranty gives you the specific legal rights and you may also have other rights which vary from state to state. Aug. 2008 SEPARATE PERMIT REQUIRED FOR: trial LTEiec tric al arpiumbing OrGas Piping City of Tukwila El.: :'_DING DIVISION 1 EC, vv; '∎1 \I\ 0: ril r' rti FILE COPY Pennft No. D11- A7 r review approval Is atiect to OMB 1;:7 :o: ,l of construction documents t} olat on of any adopted code or of fippfoved Reid Copy and ♦ _' l r • :.s BY 'Poulin .r , E • Date: , tf- I ' I City Of Ttakwila BUILDING DIVISION L REVISIONS No changes shall be made to the scope of work without prior approval of Tukwila Building Division. NOTE: Revisions will require a new plan submittal and may include additional plan review fees. !i a :awPNI qor :aot1.10.1Sfl97 0 REVIEWED FOR CODE COMPLIANCE APR 1 g 2011 City of Tukwila BUILDING niVISlnnN RECdVF� CrtYOFTU tA MAR 2 B 2011 PERMIT CENTER VI 01 1 Associated Roofing, Inc. ASSOCRI I 620(i P.O. Box 82894 206 364 4445 Kenmore, WA 800 358 3119 98028 Fax 206 368 2303 MARCH 22, 2011 CITY OF TUKWILA DEPT OF COMMUNITY DEVELOPMENT 6300 SOUTHCENTER BLVD., SUITE 100 TUKWILA, WA 98188 RE: FORMER SKARBO'S BLDG FILE COPY The existing roofing is one layer Class "B" built -up asphalt roof system installed over a 5/8" plywood deck. The new roof system to be installed is a Polyglass Polyflex G granular surfaced modified bitumen heat welded /torch applied system installed over one layer mechanically fastened 501 modified base sheet. This system is to be installed over the existing first Class B roof system. We have attached product literature and data for your review. RESPECTFULLY SUBMITTED, f TIM RESSLER SALES ENGINEER TR /jms enc OODESEWED FOR COMPLIANC E APPROVE APR City of Tukwila BUILDINP nil/mink" Serving the Pacific Northwest since 1979 RECEIVE_ CITY OF TUKKwVTLA MAN 2 8 2011 PERMIT CENTER 1(-CJ' 171'1 ..Associated Roofing, inc. ASSOCRI16206 PROPOSAL. AND CONTRACT P.O. Box 82894 This is a "plain - English" contract. "We," "us," and "our" means Kenmore, Washington 98028 Associated Roofing, Inc. "You" means the customer. 206 364 -4445 • 800 358 -3119 • 206 368 -2303 (Fax) Revised March 17, 2011 Date: FEBRUARY 11, 2011 PAGE 1 OF 2 Proposal Submitted To: JARIUS STRATTON 206 - 622 -7393 STRATTON INTERESTS FILE COPY 1411 4TH AVE, #1315 Job Name and Location: FORMER SKARBO'S BUILDING 345 ANDOVER PARK EAST TUKWILA, WA T' - File Code: A30 +26 / 1T -- ^�: ��,EVIElNED FOR ODE COMPLIANDI SEATTLE, WA 98101 PROPOSAL: We are pleased to submit this proposal to furnish the materials and perform the labor to: INSTALL FIRESTONE APP -180, OR EQUAL, GRANULAR SURFACE MODIFIED BITUM ROOF SYST ` SCOPE OF THE WORK: The specific scope of the work for this project is: APR 1 Ll. 2u 1 I 1. Remove edge metal and haul away for disposal. g 2. Apply asphalt roof primer to penetrations to be flashed as needed. City ®o ^�ff�Tij jla 3. Install 31b lead pipe fleshings on plumbing soil vent pipes and multiple -ply membrane strippin��I®�1Ue' IIpVIRIn1`' 4. Install one ply 28Ib fiberglass base sheet and mechanically fasten with simplex stronghold nails. 5. Install a Firestone APP -180, or equal, granular surface modified bitumen roof system per manufacturer's specifications. This is a torchgrade membrane with a manufacturer's ten (10) year limited material warranty. 6. All cants, curbs, and sharp angles will have additional flashing materials, installed per manufacturer's specifications, to include multiple -ply membrane stripping. 7. Install new 24 gauge sheet metal perimeter flashing with baked enamel finish using gasketed galvanized nails or hex head gasketed screws. 8. Clean up and remove all debris from contracted work. OTHER ITEMS: A. Provide and install one (1) 10" galvanized sheet metal tall cone vent with cap. B. Raise mechanical units, install specified roof system, loose lay an additional layer of cap sheet under unit support timers: reset existing timbers. Unserviceable timbers will be replaced at -an additional cost. Reset - mechanical-units. - -----• ...-- C. Fumish and install galvanized sheet metal pitchpans around electrical conduit and gas pipe penetrations. Seal in pitchpan with specified roofing materials. Fill pitchpan with plastic roof cement. Please note: Pitchpans are a maintenance item. D. Provide and install six (6) 3" edge scuppers. Reconnect existing downspouts. THE FOLLOWING PLANS, SPECIFICATIONS, AND QUALIFICATIONS ARE A PART OF THIS SCOPE OF WORK: Continued on page 2 Dollars $ Terms and Conditions Listed On Reverse Side CITYORUKVIALA WARRANTIES: Our warranty for workmanship, as described on the reverse The manufacturer's warranty, which is described in their warranty which will AUTHORIZED: side, is for years. MAR L 1011 be provided to you, is for ; MIT CENTER SIGNATURE: Associated Roofing, Inc. Associated Roofing, Inc. CUSTOMER ACCEPTANCE OF PROPOSAL This proposal is accepted. The scope of work, price, terms and conditions contained on the front and reverse of this d.' .n it the con. Ng e SIGNATURE TITLE DA RETURN ORIGINAL OF THIS PROPOSAL TO: P.O. BOX 82894, KENMORE, WASHINGTON 98028 t Associated Roofing, Inc. ASSOCRII6206 PROPOSAL AND CONTRACT P.O. Box 82894 This is a "plain - English" contract. "We," "us," and "our" means Kenmore, Washington 98028 Associated Roofing, Inc. "You" means the customer. 206 364 -4445 • 800 358 -3119 • 206 368 -2303 (Fax) Revised March 17, 2011 Date: FEBRUARY 11, 2011 PAGE 2 OF 2 Proposal Submitted To: JARIUS STRATTON 206 - 622 -7393 STRATTON INTERESTS 1411 4111 AVE, #1315 SEATTLE, WA 98101 Job Name and Location; FORMER SKARBO'S BUILDING 345 ANDOVER PARK EAST TUKWILA, WA File Code: A30 +26 / IT / TR -rr PROPOSAL: We are pleased to submit this proposal to furnish the materials and perform the labor to: _ SURFACE MODIFIED BITUMEN ROOF SYSTEM of work project. If decking repairs are necessary, there is the potential Repair to such damage is the sole responsibility of the covered, and /or secured to prevent damage. Notification to the representative. Associated Roofing is not responsible for vehicle traffic and an increased level of noise. There may objectionable, however, blease be assured this smell, as far hazard. representative is stating to the best of their knowledge there is that will be disturbed by the performance of the specified work. street/sidewalk use, or fire /torch). If required, we will obtain at of satellite dishes(s) to facilitate this project are not included of the owner. requesting a downpaymerit of 25% 10 days prior A PART OF THIS SCOPE OF WORK: FIVE & NO/100 : Dollars $ 29,955 an INSTALL FIRESTONE APP -180, OR EQUAL, GRANULAR SCOPE OF THE WORK: The specific scope of the work for this project is: EXCLUSIONS: • Deli roof • East canopy roof is not included in our scope QUALIFICATIONS TO BID: A. There will be dirt and debris associated with this for sheetrock (ceiling) damage while replacing decking. property owner. Important items should be moved, tenant(s) is the responsibility of the owner or owner's consequential damages to the structure or contents. B. As this is a construction project, there will be additional also be an odor present. Some people may find this as we know, has not been shown to be a health C. By acceptance of this contract, the owner or owner's not the existence of any asbestos containing materials D. The cost excludes all permits and fees (Le., building, the owner's expense. E. Owner to provide parking through duration of project. F. If applicable, temporary relocation and/or realignment in the scope of work and are the responsibilities G. Price valid for thirty (30) days. PLEASE NOTE: Due to the size of this project, we are to commencement of the work. THE FOLLOWING PLANS, SPECIFICATIONS, AND QUALIFICATIONS ARE TWENTY NINE THOUSAND NINE HUNDRED FIFTY Terms and Conditions Listed On Reverse Side PLUS SALES TAX WARRANTIES: Our warranty for workmanship, as described on the reverse The manufacturer's warranty, which is described in their warranty which will AUTHORIZED: TIM RESSLER side, is for FIVE years. be provided to you, is for years. SIGNATURE: I/ Associated Roofing, Inc. Associated Roofing, Inc. CUSTOMER ACCEPTANCE This proposal is accepted. The scope of work, price, terms and conditions OF PROPOSAL contained on the front and reverse of this document constitute the contract. TITLE y ✓�1; DATE '/t fit/ SIGNATURE RETURN ORIGINAL OF THIS PROPOSAL TO: P.O. BOX 82894, KENMORE, WASHINGTON 98028 • POLYFLEX® G PRODUCT DESCRIPTION PILE COPY Polyflex G membranes are premium, polyester reinforced APP modified bitumen roofing membranes specially designed for heat - welded applications. Constructed with premium Atactic Polypropylene resins, and incorporating superior polyester reinforcing, Polyflex G provides an exceptionally durable roofing product which is easy to install and will provide long-term weathering performance. With a granulated surface (available in several colors) and either a polyolefin or sand backing, Polyflex G exceeds all minimum ASTM standards for tensile strength, puncture resistance and flexibility. Polyflex G membranes can also used as flashing membranes in all applicable specifications, in accordance with recommended installation practices. USES • Heat - welded or cold - applied cap sheet • Applied directly over an acceptable substrate or as part of a multi -ply system • New roofing, re- roofing, re -cover and for flashing details FEATURES AND BENEFITS • Exceptional weathering characteristics • Puncture and tear resistant • Low -temp flexibility, exceptional tensile strength and elongation properties TECHNICAL DESCRIPTION - TEST'METHOD. .- .. PROPERTY- '. Thickness, ypical, mm (mils) TYPICAL . . - .VALUE 4.5 (180) ASTM D5147 ASTM D5147 Peak Load @ 23 + / -2C (73.4 + /- 3.6F), MD and XMD, min, kN /m (Ibf /in.) 8.8150) ASTM D5147 Elongation @ 23 + / -2C (73.4 + /- 3.6F), MD and XMD, min (%) 23 ASTM D5147 Tear Strength @ 23 + / -2C (73.4 + /- 3.6F), min, N (Ibf) 311 (70) ASTM D5147 Low Temperature Flexibility, max, C (F) 0 (32) ASTM D5147 Granule Embedment, g 2 _AVAILABLE CO! RS REO CO -;t -QOM APR 1 2611 tection is available in a variety of colors such as: ut Green Grey Slate Oak Blend Pine Green Heather Weatherwood city of Tukwila BUILDINA niviSl(1n� RECE V CITY OF TU MAR 2 8 2011 PERMIT CENTER LA PRODUCT DATA Coverage (Approx) 100 sq ft Weight 110 Ibs Roll Size 32'10" x 39 3 /e" (1 Om x lm} Rolls /Pallet 20 APPLICABLE STANDARDS • ASTM D 6222 Type l • Miami Dade Code Compliance • Factory Mutual Approved • UL Classified for use in class A, B or C roofs, as listed in the latest UL `Roofing Materials and Systems Directory" • ICC -ES# 2018 • TDI WIC' F,rw O. ES PRODUCT WARRANTY Unless otherwise incorporated into or part of a supplemental manufacturer's warranty, Polyglass warrants its product(s) for a period of 12 years against manufacturing defects in its product that directly results in leakage. Warranty coverage is an annually declining pro-rated warranty WATERPROOFING MATERIALS AND W S POLYGLASSS MA E! O S I O U P Afdl, Pattie. 1- 800 -222 -9782 .polygl om 1 Cap Sheet Base Sheet `Mechanically Attached, Per Specification) Roofing Guide Specification For: WATERPROOFING MATERIALS AND INSULATING SYSTEMS o f o u V Spec # 200W APP TOR FILE COPY Permit No. Project Name: FORMER SKARBO'S Address: 345 ANDOVER PARK EAST City, State, Zip: TUKVVILA,WA,98168 Size: 0 Base Sheet : Polyglass Base Cap Sheet : Polyflex G Prepared by: Neisinger, William 1 REVIEWED FOR CODE COMPLIANCE APR 1 n. 2uil City of Tukwila BUILDINP nnngln�� Please see the POLYGLASS Technical Guide or contact POLYGLASS Technical Support for further information regarding slope limitations and specific application requirements a POLYGLASS Torch Applied Roofing System. This specification is provided as a general guide for use of POLYGLASS products based on typical building conditions and standard roofing practices. POLYGLASS is strictly a manufacturer of roofing systems and has no experience, training or expertise in the areas of architecture /engineering or in the area of consulting with respect to matters related to such areas. RECEI CrtV OF TuroviLA MAR 282011 PERMIT CENTER DtiO11 PART 1 GENERAL 1.01 General Notes Preceding the start up of job, the contractor shall decide to his satisfaction that all the specifications are workable as specified, that there is nothing that would deter the contractor s required warranty, and that no existing conditions at the site prevent the contractor from performing the job in a professional and safe manner. When the job starts, it will be assumed that the contractor approves the existing conditions and the specifications. 1.02 Description Provide all labor, materials, equipment, supervision and incidentals as needed to install a complete Polyglass reinforced modified bituminous roofing system over a new or accepted, prepared exiting roof substrate. All details of installation shall conform to Polyglass Specifications, Details and General Recommendations. 1.03 Quality Assurance Products used in the work of this Section shall be manufactured by Polyglass or accepted for use in conjunction with the products manufactured by Polyglass. The Roofing Contractor and his personnel shall be currently accepted by Polyglass as qualified to install the materials of this section. Do not apply roofing during inclement weather. Do not apply roofing membrane to damp frozen, dirty or dusty surfaces. Part 2 PRODUCTS 2.01 Polyglass Base - An APP modified bitumen roofing membrane base sheet, reinforced with a fiberglass mat, saturated and coated with a polymerized asphaltic compound with exceptional waterproofing and weatherability. Specially designed for heat welding, cold -apply and mechanically attached applications. Top and bottom surfaces are finished with polyolefin film or sand. 2.02 Polyflex G - Premium, polyester reinforced APP modified bitumen roofing membranes specially designed for heat welded and cold -apply applications. Membrane is also used as a flashing in all applicable specifications, in accordance with recommended installation practices. Membrane is polyester reinforced, Lightweight, weather resistant and durable. Top surface of membrane is granular except at selvage, which is granule free. 2.03 Asphalt Primer Meeting ASTM D 41 specification, applied in strict conformance to manufacturers recommendations. 2.04 Asphalt Meeting ASTM D 312 Type 111 or IV. Follow installation recommendations of the NRCA (National Roofing Contractors Association) 2.05 Surface Coating (where required by specification) emulsion coating, asphalt latex emulsion roof surfacing material, asphaltic based aluminum roof coating (fibrated or non- fibrated) or a colored acrylic coating, may be required to meet necessary fire code approvals. Consult Polyglass Technical Service Department, 1- 800 - 894 -4563 for fire rated assembly information. 2.06 Product Handling a. All materials, except those that are shop fabricated shall be delivered to the job site with their original labels intact. Bulk materials shall be identified by the manufacturer as to specification issued. b. All materials shall be stored in accordance with the instructions of the manufacturer prior to their application or installation. No wet or damaged materials will be used in the application. Materials stored on the job site shall be a minimum 4" off the ground of the roof. c. Application of all roofing shall be Page 2 accomplished in such a way that each area will be complete at the end of each days work. All roof edges and incomplete flashing shall be protected against water entry, particularly between work periods. d. When ambient temperature is below 40 degrees F, care must be exercised in handling and storing Polyglass membrane. Only rolls for immediate application shall be exposed to the elements. All masonry, concrete and sheet metal surfaces incorporated into the roof system shall be primed with asphalt primer meeting ASTM D-41 specification and allowed to dry prior to installing bituminous roofing materials. e. Wood curbs or nailers, where required, shall be pressure treated with accepted pressure treatment meeting AWAP Standard P -5. Part 3 Execution 3.01 General Preparation The roof surface, which is to receive the Polyglass roofing system, shall be smooth, clean, free from loose gravel, dirt and debris, dry and structurally sound 3.02 Reroofing a. Remove existing roof flashings from curbs and parapet walls down to the surface of the roof. Remove existing flashings at roof drains and roof penetrations. b. Remove all wet, deteriorated, blistered or delaminated roofing membrane or insulation and fill in any low spots occurring as a result of removal work, to create a smooth even surface for application of new roof membranes. c. Existing roof surfaces shall be primed as necessary with asphalt primer meeting ASTM D-41 specification and allowed to dry prior to installing the Polyglass roofing system. 3.03 Installation a. Decks Prime where required, in accordance with requirements and recommendations of the primer and deck manufacturer (if applicable). b. Where a vapor retarder is required by the specifier Follow the instructions with regard to the particular materials specified and install in accordance with the recommendations of the manufacturer and the requirements of the architect. 3.04 Membrane a. The corresponding application methods will appear here b. For each method selected 3.05 Flashing a. The flashing shall be installed using Polyglass flashing sheets and minimum 6" wide Polyglass stripping sheets. The stripping sheet shall be installed with a minimum of three inches in both the horizontal and vertical surfaces. The flashing sheets shall be installed with a minimum of six inches on the horizontal surface and extend a minimum of eight inches above the finished roof surface. b. The flashing sheets shall be installed by the same application method used for the roof membranes. In hot mop applications the flashing sheets may be installed by heat weld application provide the proper flashing materials are utilized. The top edge of the flashing sheet shall be secured using a termination bar (only when the wall surface above is waterproofed), or nailed 4" on center and covered with an acceptable counter flashing. c. Items related to reproofing operations such as sheet metal gravel stops, roof vents, and similar items shall be incorporated into the new roof system in accordance with the recommendations described in the current issued of the Polyglass "Specifications and Details" manual NOTE: Never use torch or apply torched materials to areas of combustible materials. Any combustible material must first be overlaid with a protective barrier or alternatively remove such materials from the location. Use common sense in the application of torches. Always keep a suitable, prepared, fire extinguisher available at each area where torching occurs. r TGFU.R14571 - Roofing Systems FILE COPY A....... AA a di,A ONLINE CERTIFICATIONS DIRECTORY Page 1 of 8 TGFU.R14571 Roofing Systems Page Bottom See General Information for Roofing Systems POLYGLASS USA INC 150 LYON DR FERNLEY, NV 89408 USA Roofing Systems SINGLE PLY MEMBRANE SYSTEMS f REVIEWED FOR E ODE COMPLIANCE R14571 APR 1 a 2011 City of Tukwila BUILDING nIVIRIfN Unless otherwise indicated, the insulation and base sheet are mechanically fastened in place; the membrane is heat welded In place. (Optional) Noncombustible deck classifications are applicable for use over combustible (15/32 in. min plywood) decks when 1/2 in. (min) gypsum board or 1/4 in. (min) G -P Gypsum "DensDeck @ Roofboard ", "DensDeck Prime@ Roofboard ", "DensDeck DuraGuard"" Roofboard" or 1/4 in. (min) USG Corp SECUROCKTM Roof Board Type FRX -G are used directly over the combustible deck with all joints staggered 6 in. (min) from plywood joints. Unless otherwise indicated, in any noncombustible roof deck Classification any UL Classified insulation may be utilized underneath a layer of 1/4 in. (min) G-P Gypsum "DensDeck @ Roofboard ", "DensDeck Prime@ Roofboard ", "DensDeck DuraGuard"" Roofboard" or I/4 in. (min) USG Corp SECUROCKTM Roof Board Type FRX -G. General statement for use of vapor retarders and /or deck/insulation adhesives (NC decks only): When such vapor retarders or deck/insulation adhesives are acceptable to POLYGLASS they may be utilized. "POLYGLASS BASE ", "MODIBASE ", "Polyglass G2 Base" may be used in lieu of any Type G2 base sheet in any NC Classification. These products may also be used in any C -15/32 Classification in which a generic Type G2 is referenced (i.e. not brand specific). "POLYGLASS Ply 4 ", " POLYGLASS Ply 6" (Type G1) and " POLYGLASS VENTED BASE" may be used in any NC Classification. These products may also be used in any C -15/32 Classification In which a generic Type G1 is referenced (i.e. not brand specific). References to polyisocyanurate Insulation may Include Polyglass Products "POLYTHERM@" and "POLYTHERM@ Tapered ". Acceptable alternates to the membranes listed are given below: Membrane Listed Acceptable Alternatives "POLYBOND" "MODIBOND" "POLYBOND G" "MODIBOND G" "Polytherm ", "Polytherm Tapered" or "Polytherm Composite" insulations may be used wherever polyisocyanurate insulations are specified in the Classifications below. Insulation may be optional for any non - combustible deck roofing system unless the insulation acts as a coverboard over another innssa} c 1 r/ edficBV 6iOVF6,1� a LA MAR 282011 1. Deck: C -15/32 Class A - Ballasted Incline: 3 PERMIT CENTER Insulation: — Polyisocyanurate, urethane, perlite / polyisocyanurate composite, perlite /urethane composite, glass fiber, p enolic or pe Ite, any thickness. Ply or Base Sheet: — One ply "ELASTOBASE ", "ELASTOFLEX V or "ELASTOSHIELD TS G. Membrane: — One or more layers "POLYGLASS 350 CAP ", "POLYFRESKO 350 CAP ", "POLYBOND ", " POLYBOND G ", "POLYFLEX ", "POLYFRESKO TORCH" or "POLYFLEX G" (modified bitumen), heat welded, or one or more layers "ELASTOFLEX V ", "ELASTOBASE ", "ELASTOFLEX S6" or "ELASTOSHIELD TS G ", mopped in hot asphalt or heat fused. Surfacing: — Gravel, embedded in hot mopping asphalt. Class B - Ballasted P1' 011 http:// database. ul. com /cgi- bin/XYV /template/LISEXT /1 FRAME /showpage.html ?name =T... 3/23/2011 TGFU.R14571 - Roofing Systems Page 2 of 8 • 1. Deck: C -15/32 Incline: 3 Base Sheet: — Type G2. Membrane: — "POLYBOND ", "POLYGLASS 350 CAP ", "POLYFRESKO 350 CAP ", "POLYBOND G ", "POLYFLEX ", "POLYFRESKO TORCH ", " POLYFLEX G" (modified bitumen), heat welded, or one or more layers "ELASTOFLEX V ", "ELASTOBASE ", "ELASTOFLEX S6" or "ELASTOSHIELD TS G ", mopped in hot asphalt. Surfacing: — Gravel, embedded in hot mopping asphalt or heat fused. Class A - Fully Adhered 1. Deck: NC Incline: 1/2 Insulation (Optional): — Polyisocyanurate, urethane, perlite /polyisocyanurate composite, perlite/urethane composite, glass fiber, phenolic or perlite, any thickness. Base Sheet — One or more layers "ELASTOBASE ", "POLYFLEX ", "ELASTOFLEX V" or Type G2 base sheet. Membrane: — "POLYBOND ", "POLYBOND G ", "POLYFLEX ", "POLYFRESKO TORCH" or " POLYFLEX G" (modified bitumen), heat welded. Surfacing: — Kokem Products "Sunguard Acrylic Roof Coating" at 1 gal /sq; or Karnak No. 97 Fibrated Aluminum Asphalt Roof Coating or Karnak No. 97 Asbestos Free Aluminum Roof Coating at 1 to 2 gal/ sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq., followed by "PolyPlus 60 ", applied at 3/4-1 gal. /sq. . 2. Deck: C -15/32 Incline: 1/2 Insulation: — Two or more layers (insulation joints staggered a min of 6 in. from plywood deck joints) polyisocyanurate, perlite /polyisocyanurate composite, perlite /urethane composite, glass fiber, phenolic or perlite, any thickness. Base Sheet — One or more layers "ELASTOBASE ", "POLYFLEX ", "ELASTOFLEX V" or Type G2 base sheet. Membrane: — "POLYBOND ", "POLYBOND G ", "POLYFLEX ", "POLYFRESKO TORCH" or " POLYFLEX G" (modified bitumen), heat welded. Surfacing: — Kokem Products "Sunguard Acrylic Roof Coating" at 1 gal /sq; or Karnak No. 97 Fibrated Aluminum Asphalt Roof Coating or Kamak No. 97 Asbestos Free Aluminum Roof Coating at 1 to 2 gal/ sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq., followed by "PolyPlus 60 ", applied at 3/4-1 gal. /sq.. 3. Deck: C -15/32 Incline: 1/2 Insulation: — 1/4 in. thick G -P Gypsum DensDeck®, perlite, wood flber or glass fiber, 1 in., mechanically fastened. Base or Ply Sheet: — One or more layers " POLYFLEX" (mechanically fastened or heat welded), "ELASTOBASE ", "ELASTOFLEX V" or Type G2 base sheet (mechanically fastened or hot mopped). Membrane: — "POLYBOND ", "POLYBOND G ", "POLYFLEX ", "POLYFRESKO TORCH" or " POLYFLEX G" (modified bitumen), heat welded or hot mopped. Surfacing: — Monsey Products "Endure Aluminum Roof Coating ", "Weather Check" or "Pro-Grade Aluminum Roof Coating ", 1.5 gal /sq; or Karnak No. 97 Fibrated Aluminum Asphalt Roof Coating or Karnak No. 97 Asbestos Free Aluminum Roof Coating at 1 to 2 gal/ sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq., followed by "PolyPlus 60 ", applied at 3/4-1 gal. /sq.. 4. Deck: NC Incline: 1 Insulation (Optional): — Polyisocyanurate, glass fiber, perlite, wood fiber, any combination, any thickness. Base Sheet: — " POLYFLEX" (mechanically fastened or heat welded) or Type G2, mechanically fastened or hot mopped. Membrane: — "POLYBOND ", "POLYBOND G ", "POLYFLEX ", "POLYFRESKO TORCH" or " POLYFLEX G" (modified bitumen), heat welded. Surfacing: — Grundy Industries "al MB Aluminum Roof Coating" at 1 -2 gal /sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq., followed by "PolyPlus 60 ", applied at 3/4-1 gal. /sq.. 5. Deck: NC Incline: 1 Insulation (Optional): — Polyisocyanurate, urethane, perlite /polyisocyanurate composite, perlite /urethane composite, glass fiber, phenolic, perlite or wood fiberboard, any thickness. Base Sheet: — One or more layers "POLYFLEX" (heat fused or mechanically fastened), "ELASTOBASE ", "ELASTOFLEX V" or Type G2 base sheet (hot mopped, heat fused or mechanically fastened). Membrane: — "DUFLEX G FR ", "POLYFRESKO TORCH FR" or " POLYFLEX G FR" (modified bitumen), heat fused. 6. Deck: C -15/32 Incline: 1/2 Base Sheet: — One or more layers " POLYFLEX" or "POLYGLASS Base" (heat fused or mechanically fastened), "ELASTOBASE ", "ELASTOFLEX V" or Type G2 base sheet (hot mopped, heat fused or mechanically fastened). Ply Sheet: — One or more layers " POLYFLEX" or "POLYGLASS Base" (heat fused) or "POLYGLASS Base ", "ELASTOBASE ", "ELASTOFLEX V" or Type G2 base sheet (hot mopped) or mechanically attached. Membrane: — "DUFLEX G FR ", "POLYFRESKO TORCH FR" or " POLYFLEX G FR" (modified bitumen), heat fused. 7. Deck: C -15/32 Incline: 1/2 Insulation: — Polyisocyanurate (2 in. min), perlite (3/4 in. min), glass fiber (7/16 in. min), perlite /polyisocyanurate composite, perlite /urethane composite (2 in. min) or (2 in. min) polyisocyanurate covered with 1/2 in. perlite or wood fiberboard. Base Sheet: — One or more layers " POLYFLEX" (heat fused or mechanically fastened), "ELASTOBASE ", "ELASTOFLEX V" (heat fused, http: // database. ul. com /cgi- bin/XYV /template/LISEXT /1 FRAME/showpage.html ?name =T... 3/23/2011 TGFU.R14571 - Roofing Systems Page 3 of 8 mechanically fastened or hot mopped) or Type G2 base sheet (hot mopped or mechanically fastened). Ply Sheet: — One or more layers " POLYFLEX" (heat fused) "ELASTOBASE ", " ELASTOFLEX V" or Type G2 base sheet (hot mopped) or mechanically fastened. Membrane: — "DUFLEX G FR ", " POLYFRESKO TORCH FR" or " POLYFLEX G FR" (modified bitumen), heat fused. 8. Deck: NC Incline: 1/2 Insulation (Optional): — Polyisocyanurate, urethane, perlite /polyisocyanurate composite, perlite /urethane composite, glass fiber or wood fiberboard, phenolic or perlite, any thickness. Base Sheet: — One or more layers " POLYFLEX" (heat fused or mechanically fastened), "ELASTOBASE ", " ELASTOFLEX V" (hot mopped, mechanically fastened or heat fused) or Type G2 base sheet (hot mopped or mechanically fastened). Membrane: — " ELASTOSHIELD TS G FR", " ELASTOFLEX S6 G FR" or "POLYFRESKO MOP FR" (modified bitumen), hot mopped or heat fused. 9. Deck: C -15/32 Incline: 1/2 Base Sheet: — One or more layers " POLYFLEX" (heat fused or mechanically fastened), "ELASTOBASE ", " ELASTOFLEX V" or Type G2 base sheet (hot mopped or mechanically fastened). Ply Sheet: — One or more layers " POLYFLEX" (heat fused), "ELASTOBASE ", " ELASTOFLEX V" or Type G2 base sheet (hot mopped or mechanically attached). Membrane: — " ELASTOFLEX S6 G FR', "POLYFRESKO MOP FR" or "ELASTOSHIELD TS G FR" (modified bitumen), hot mopped or heat fused. 10. Deck: C -15/32 Incline: 1/2 Insulation: — Polyisocyanurate (2 in. min), perlite (3/4 in. min), glass fiber (15/16 in. min), perlite /polylsocyanurate composite, perlite /urethane composite (2 in. min). Base Sheet: — One or more layers " POLYFLEX" (heat fused or mechanically fastened), "ELASTOBASE ", " ELASTOFLEX V" or Type G2 base sheet (hot mopped or mechanically fastened). Ply Sheet: — One or more layers " POLYFLEX" (heat fused), "ELASTOBASE ", " ELASTOFLEX V" or Type G2 base sheet (hot mopped or mechanically attached). Membrane: — " ELASTOFLEX S6 G FR ", " POLYFRESKO MOP FR" or " ELASTOSHIELD TS G FR" (modified bitumen), hot mopped or heat fused. 11. Deck: NC Incline: 1 Insulation (Optional): — Cellular concrete, gypsum concrete, vermiculite concrete, perlite concrete or structural concrete. Primer: — Not UL Classified — as required by manufacturer. Membrane: — "POLYBOND ", "POLYBOND G ", "POLYFLEX ", " POLYFLEX G ", " POLYFLEX G FR ", " POLYFRESKO TORCH FR ", "POLYFLEX ", "POLYFLEX G ", "DUFLEX G FR" or "POLYFLEX G FR ". Surfacing: — (not required for "POLYFLEX G FR ", " POLYFRESKO TORCH FR" or "DUFLEX G FR" ) Monsey Products "Endure Aluminum Roof Coating ", at 1.5 gal /sq; or Grundy Industries "al MB Aluminum Roof Coating ", at 1 -2 gal /sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq., followed by "PolyPlus 60 ", applied at 3ys -1 gal. /sq. 12. Deck: NC Incline: 1 Insulation (Optional): — Any thickness, one or more layers UL Classified perlite, wood fiber, glass fiber, polyisocyanurate, polyisocyanurate /composite, EPS /wood fiber, EPS /perlite or EPS /composite. Base Sheet: — One or more layers Type Gi or G2. Membrane: — One or more layers "POLYBOND ", "POLYBOND G ", " POLYFLEX" or "POLYFLEX G" (modified bitumen), heat fused. Surfacing: — Fields "F350 Heat Shield Aluminum Coating" or "F630 Heat Shield Fibered Aluminum Coating ", 1 -1/2 gal /sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq., followed by "PolyPlus 60 ", applied at 34 -1 gal. /sq. 13. Deck: NC Incline: 1/2 Barrier Board (Optional): — 1/2 in. gypsum board. Insulation (Optional): — Polyisocyanurate, any thickness. Base Sheet (Optional): — Type G2, "ELASTOBASE ", " ELASTOFLEX V" or "POLYFLEX ". Membrane: — " POLYFLEX G FR ", " POLYFRESKO TORCH FR ", "DUFLEX G FR" (heat fused), "ELASTOFLEX S6 G FR ", " POLYFRESKO MOP FR" (hot mopped) or "ELASTOSHIELD TS G FR" (heat fused or hot mopped). 14. Deck: C -15/32 Incline: 1 Insulation: — 1/4 In. thick G -P Gypsum DensDeck®, pertite, wood fiber or glass fiber, 1 In., mechanically fastened. Ply Sheet: — Type G2, mechanically fastened. Membrane: — "POLYBOND ", " POLYFLEX" (modified bitumen), heat welded. Surfacing: — Monsey Products "Endure Aluminum Roof Coating ", "Weather Check" or "Pro-Grade Aluminum Roof Coating ", 1.5 gal /sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal, /sq., followed by "PolyPius 60 ", applied at 34 -1 gal. /sq. 15. Deck: NC Incline: 1/2 http: // database. ul. com /cgi- bin/XYV /template/LISEXT /1 FRAME /showpage.html ?name =T... 3/23/2011 TGFU.R14571 - Roofing Systems Page 4 of 8 Insulation (Optional): — Polyisocyanurate, perlite, glass fiber or wood fiberboard, any thickness. Base Sheet: — On ply Type G2, hot mopped or mechanically fastened or "ELASTOBASE ", heat fused, hot mopped or mechanically fastened. Membrane: — " ELASTOFLEX S6 G FR ", " POLYFRESKO MOP FR" or "ELASTOSHIELD TS G FR" hot mopped or heat fused. 16. Deck: C -15/32 Incline: 1/2 Base Sheet; — One ply Type G2 or "ELASTOBASE ", mechanically fastened. Ply Sheet: — One ply Type G2 (hot mopped or mechanically fastened) or "ELASTOBASE" (hot mopped, heat fused or mechanically fastened). Insulation (Optional): — Polyisocyanurate, perlite, glass fiber, any thickness. Membrane: — " ELASTOFLEX S6 G FR ", " POLYFRESKO MOP FR" or, ELASTOSHIELD TS G FR " hot mopped or heat fused. 17. Deck: C-15/32 Incline: 1/2 Insulation: Polyisocyanurate (2 in. min), glass fiber (15/16 in. min), perlite/polyisocyanurate composite, perlite /urethane composite (2 in. min). Base Sheet: — One or more layers " POLYFLEX" (heat fused or mechanically fastened), "ELASTOBASE ", " ELASTOFLEX V" (hot mopped or heat fused) or Type G2 base sheet (hot mopped or mechanically fastened). Ply Sheet (Optional): — One or more layers "POLYFLEX" (heat fused), "ELASTOBASE ", " ELASTOFLEX V" (hot mopped or heat fused) or Type G2 base sheet (hot mopped or mechanically fastened). Membrane: — "DUFLEX G FR ", " POLYFRESKO TORCH FR" or "POLYFLEX G FR" (modified bitumen), heat fused. 18. Deck: C -15/32 Incline: 1/2 Insulation: — Polyisocyanurate (2 in. min), glass fiber (15/16 in. min), perlite /polyisocyanurate composite, perlite /urethane composite (2 in. min). Base Sheet: — One or more layers "POLYFLEX" (heat fused or mechanically fastened), "ELASTOBASE ", " ELASTOFLEX V" or Type G2 base sheet (hot mopped or mechanically fastened). Ply Sheet (Optional): — One or more layers "POLYFLEX" (heat fused), "ELASTOBASE ", " ELASTOFLEX V" or Type G2 base sheet (hot mopped or mechanically fastened). Membrane: — " ELASTOFLEX S6 G " or "POLYFRESKO MOP" (modified bitumen), hot mopped. 19. Deck: C -15/32 Incline: 1 Insulation: — 1/4 in. thick G -P Gypsum DensDeck ®, perlite, wood fiber or glass fiber, 1 in., mechanically fastened. Ply Sheet: — Type G2, mechanically fastened. Membrane: — "POLYFLEX ", heat welded. Surfacing: — Monsey Products "Endure Aluminum Roof Coating ", "Weather Check" or "Pro-Grade Aluminum Roof Coating ", 1.5 gal /sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq., followed by "PolyPlus 60 ", applied at 3/4-1 gal. /sq.. 20. Deck: C -15/32 Incline: 2 -1/2 Barrier Board: — 1/4 in. (min) G -P Gypsum DensDeck® with all joints staggered 6 In. from the plywood joints. Base Sheet: — Type G2, mechanically fastened. Membrane: — " POLYFLEX G FR" or " POLYFRESKO TORCH FR ", heat fused in place. 21. Deck: C -15/32 Incline: 2 Insulation (Optional): — Polyisocyanurate, perlite, wood fiber or polyisocyanurate /perlite board, any thickness. Barrier Board: — 1/4 in. (min) G -P Gypsum DensDeck ®, mechanically fastened with all joints staggered 6 In. from the plywood joints. Base Sheet: — "ELASTOBASE" (poly /sand), mechanically fastened or " ELASTOFLEX SA V PLUS FR "or "ELASTOFLEX SA V FR BASE VENT" (self adhered). Ply Sheet (Optional): — " ELASTOFLEX SA V PLUS FR" or "ELASTOFLEX SA V FR BASE VENT', (self adhered). Membrane: — " POLYFLEX SA P FR ", " POLYFRESKO APP SA P FR ", " ELASTOFLEX SA P FR ", " POLYFRESKO SBS SA P FR ", " ELASTOFLEX SA V FR HT", (self adhered) or "POLYFLEX G FR ", " POLYFRESKO TORCH FR ", "DUFLEX G FR ", " ELASTOFLEX 56 G FR ", " POLYFRESKO MOP FR ", "ELASTOSHIELD TS G FR ", heat fused. 22. Deck: C -15/32 Incline: 1/2 Insulation (Optional): — Polyisocyanurate 1.5 in. (min.) with all joints staggered 6 -In. (min.) from the plywood joints. Base Sheet: — Type G2, mechanically fastened followed by "ELASTOBASE ", mechanically fastened. Ply Sheet (Optional): — " ELASTOFLEX SA V PLUS FR" or "ELASTOFLEX SA V FR BASE VENT ", (self adhered). Membrane: — " POLYFLEX SA P FR ", " POLYFRESKO APP SA P FR ", " ELASTOFLEX SA P FR ", " POLYFRESKO SBS SA P FR ", or "DUFLEX G FR ", " POLYFLEX G FR ", " ELASTOFLEX S6 G FR ", " POLYFRESKO MOP FR ", " ELASTOSHIELD TS G FR ", heat fused. 23. Deck: NC Incline: 2 Insulation (Optional): — Atlas Roofing "ACFoam III" or " ACFoam II" or Hunter Panels "H- Shield ", any thickness. Base Sheet: — "ELASTOBASE" (poly /sand), heat fused or mechanically fastened or "ELASTOFLEX SA V PLUS FR" or "ELASTOFLEX SA V FR http: // database. ul. com /cgi- bin/XYV /template/LISEXT /1 FRAME /showpage.html ?name =T... 3/23/2011 TGFU.R14571 - Roofing Systems Page 5 of 8 BASE VENT', (self adhered). Membrane: — "POLYFLEX SA P FR ", " POLYFRESKO APP SA P FR ", " ELASTOFLEX SA P FR ", " POLYFRESKO SBS SA P FR ", " ELASTOFLEX SA V FR HT', (self adhered) or "POLYFLEX G FR ", " POLYFRESKO TORCH FR ", "DUFLEX G FR ", " ELASTOFLEX S6 G FR ", " POLYFRESKO MOP FR ", " ELASTOSHIELD TS G FR ", heat fused. 24. Deck: C -15/32 Incline: 3 Insulation (Optional): — Polyisocyanurate, periite, wood fiber or polyisocyanurate/perllte board, any thickness. Barrier Board: — 1/4 In. (min) G -P Gypsum DensDeck®, mechanically fastened with all joints staggered 6 In. from the plywood joints. Base Sheet: — "ELASTOBASE" (poly /sand), mechanically fastened. Ply Sheet (Optional): — " ELASTOFLEX SA V PLUS FR" or " ELASTOFLEX SA V FR BASE VENT ", (self adhered). Membrane: — " ELASTOFLEX S6 G FR" or "POLYFRESKO MOP FR ", heat fused. 25. Deck: NC incline: 3 Insulation (Optional) : — Atlas Roofing "ACFoam III" or "ACFoam II" or Hunter Panels "H- Shield ", any thickness. Base Sheet: — " ELASTOFLEX SA V PLUS FR" or " ELASTOFLEX SA V FR BASE VENT" (self adhered). Membrane: — "POLYFLEX SA P FR ", " POLYFRESKO APP SA P FR ", " ELASTOFLEX SA P FR" or " POLYFRESKO SBS SA P FR" (self adhered). 26. Deck: NC Incline: 1/2 Base Sheet: — Type G1 or G2, mechanically fastened. Membrane: — "POLYFLEX G" or "POLYBOND G ", heat fused. 27. Deck: NC Incline: 3 Membrane: — "POLYFLEX SA P FR ", " POLYFRESKO APP SA P FR ", " POLYFRESKO S8S SA P FR "or "ELASTOFLEX SA P FR" (self adhered). 28. Deck: NC Incline: 1 Insulation (Optional): — Polyisocyanurate, any thickness. Base sheet (Optional): — " ELASTOFLEX SA V PLUS" or " ELASTOFLEX SA V BASE VENT", self- adhered or "ELASTOBASE" (poly /sand), mechanically fastened. Membrane: — "POLYFLEX SA P" or " POLYFRESKO APP SA P" self - adhered. 29. Deck: C -15/32 Incline: 1/2 Insulation: — Polyisocyanurate (2 In. min), glass fiber (15/16 in. min), perlite /polyisocyanurate composite, perlite /urethane composite (2 in. min). Barrier Board: — 1/4 in. (min) G -P Gypsum DensDeck®, mechanically fastened, with 6 in. offset to plywood joints. Base Sheet: — " ELASTOFLEX S6" (heat fused or mechanically fastened). Membrane: — " ELASTOFLEX S6 G " or "POLYFRESKO MOP ", (heat fused). 30. Deck: NC Incline: 1/2 Insulation (Optional) — Atlas Roofing "ACFoam III" or "ACFoam II ", any thickness. Base Sheet — " ELASTOFLEX SA V PLUS FR" or " ELASTOFLEX SA V FR BASE VENT ", (self adhered). Membrane: — "POLYKOOL SA" (self adhered). 31. Deck: 5/32 Incline: 1/2 Base Sheet: — G2 Base sheet mechanically fastened followed by " ELASTOFLEX SA V PLUS FR" or " ELASTOFLEX SA V FR BASE VENT", (self adhered). Membrane: — "POLYKOOL SA" (self adhered). 32. Deck: NC Incline: 1/2 Insulation (Optional): — Polyisocyanurate, any thickness. Base sheet (Optional): — " ELASTOFLEX SA V PLUS" or "ELASTOFLEX SA V BASE VENT', self - adhered or "ELASTOBASE" (poly /sand), mechanically fastened. Membrane: — " ELASTOFLEX S6 G " or "POLYFRESKO MOP ", heat fused. 33. Deck: NC Incline: 1 -1/4 Insulation (Optional): — Any UL Classified isocyanate or polyurethane, any thickness. Base sheet: J.- " ELASTOFLEX SA V PLUS FR" or " ELASTOFLEX SA V FR BASE VENT', self adhered. Membrane: — "POLYKOOL SA" self adhered. http: // database. ul. com /cgi- bin/XYV /template/LISEXT /1 FRAME /showpage.html ?name =T... 3/23/2011 TGFU.R14571 - Roofing Systems Page 6 of 8 34. Deck: NC Incline: 1 Insulation (Optional): — Any UL Classified polyisocyanate, any thickness. Base Sheet: — " ELASTOFLEX SA V PLUS FR" or "ELASTOFLEX SA V FR BASE VENT ", self adhered. Membrane: — "POLYBIANKO APP SAP ", self adhered. Class B - Fully Adhered 1. Deck: C -15/32 Incline: 1/4 Base Sheet: — Two or more layers " POLYFLEX" (mechanically fastened or heat fused), "ELASTOBASE ", Type G2 GAF Building Materials "GAFGIas #75 ", Johns Manville "GLASBASE" or Celotex "Vaporbar GB" (mechanically fastened or hot mopped in place). Membrane: — " POLYFLEX G" (modified bitumen), heat welded. 2. Deck: C -15/32 Indine: 1/2 Insulation (Optional): — Any thickness, one or more layers UL Classified periite, wood fiber, glass fiber, polyisocyanurate, polyisocyanurate/composite, EPS /wood fiber, EPS /periite or EPS /composite roof insulation. Base Sheet: — One or more layers Type G1 or G2. Membrane: — One or more layers "POLYFLEX G FR ", " POLYFRESKO TORCH FR ", "POLYBOND ", "POLYBOND G ", " POLYFLEX" or " POLYFLEX G" (modified bitumen), heat fused. Surfacing: — Fields "F530 Heat Shield Aluminum Coating" or "F630 Heat Shield Fibered Aluminum Coating ", 1 -1/2 gal /sq; or Monsey Products "Endure Aluminum Roof Coating ", "Weather Check" or "Pro-Grade Aluminum Roof Coating ", 1 -1/2 gal /sq; or Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq., followed by "PolyPlus 60 ", applied at 3/4-1 gal. /sq. 3. Deck: C -15/32 Incline: 1 -1/2 Base Sheet: — Type G2 or "ELASTOBASE ", mechanically fastened. Ply Sheet: — "Polyglass Base ", heat fused. Membrane: — " POLYFLEX G FR" or "POLYFRESKO TORCH FR" (modified bitumen), heat fused. 4. Deck: 15/32 Incline: 1 -1/2 Insulation: — Glass fiber (15/16 in. min.), mechanically fastened. Base Sheet: — Type G2 base or "ELASTOBASE ", hot mopped or mechanically fastened. Membrane: — " POLYFLEX G FR" or " POLYFRESKO TORCH FR" (modified bitumen), heat fused. 5. Deck: C -15/32 Incline: 1/2 Base Sheet: — Type G2, mechanically fastened. Membrane: — " POLYFLEX G" or "POLYBOND G ", heat fused. 6.. Deck: NC Indine: 1 Insulation (Optional): — Poiyisocyanurate, any thickness. Base sheet (Optional): — " ELASTOFLEX SA V PLUS" or " ELASTOFLEX SA V BASE VENT", self - adhered or "ELASTOBASE" (poly /sand), mechanically fastened. Ply Sheet (Optional): — "POLYFLEX ", heat fused. Membrane: — " POLYFLEX SA P ", " POLYFRESKO APP SA P ", " ELASTOFLEX SA P ", " POLYFRESKO SBS SA P ", self- adhered or 'POLYFLEX G ", heat fused. 7. Deck: C -15/32 Incline: 1 /2 Insulation (Optional): — Polylsocyanurate, any thickness. Barrier Board: — 1 /4 -in. (min) GP Gypsum DensDeck® or DensDeck Prime ®, mechanically fastened. Base sheet: — "ELASTOBASE" (poly /sand), mechanically fastened. Ply sheet (Optional): — " ELASTOFLEX SA V PLUS" or " ELASTOFLEX SA V BASE VENT ", self - adhered. Membrane: — " POLYFLEX SA P", " POLYFRESKO APP SA P ", " ELASTOFLEX SA P", "POLYFRESKO SBS SA P ", self- adhered or 'POLYFLEX G ", heat fused. 8. Deck: C -15/32 Incline: 1/4 Base sheet (Optional): — "ELASTOBASE" (poly /sand), mechanically fastened. Ply Sheet: — " ELASTOFLEX SA V PLUS° or " ELASTOFLEX SA V BASE VENT', self- adhered or "ELASTOBASE ", mechanically fastened. Membrane: — " POLYFLEX SA P", "POLYFRESKO APP SA P", " ELASTOFLEX SA P ", " POLYFRESKO SBS SA P", self- adhered or 'POLYFLEX G ", heat fused. 9. Deck: NC Incline: 1 http: // database. ul. com /cgi- bin/XYV /template/LISEXT /1 FRAME /showpage.html ?name =T... 3/23/2011 TGFU.R14571 - Roofing Systems Page 7 of 8 Insulation: — Any UL Classified, any thickness. Barrier Board: — 1/4, 3/8, 1/2 or 5 /8 -in. thick USG Corp "SECUROCKTM Roof Board (Type FRX -G)" Base sheet (Optional): — "ELASTOFLEX SA V PLUS" or "ELASTOFLEX SA V BASE VENT ", self- adhered or "ELASTOBASE" (poly /sand), mechanically fastened. Ply Sheet (Optional): — "POLYFLEX ", heat fused. Membrane: — " POLYFLEX SA P ", "POLYFRESKO APP SA P ", "ELASTOFLEX SA P ", "POLYFRESKO SBS SA P ", self- adhered or 'POLYFLEX G ", heat fused. 10. Deck: C -15/32 Incline: 2 Insulation (Optional): — Polyisocyanurate, periite, wood fiber or polyisocyanurate /perlite board, any thickness. Barrier Board: — 1/4 in. (min) G -P Gypsum DensDeck®, mechanically fastened with all joints staggered 6 in. from the plywood joints. Base Sheet: — "ELASTOBASE" (poly /sand), mechanically fastened, heat fused or hot mopped. Ply Sheet (Optional): — "ELASTOBASE" (poly /sand), mechanically fastened, heat fused or hot mopped. Membrane: — " POLYFLEX SA P FR ", "POLYFRESKO APP SA P FR ", "ELASTOFLEX SA P FR ", "POLYFRESKO SBS SA P FR ", "ELASTOFLEX SA V FR HT ", (self adhered) or "POLYFLEX G FR ", "POLYFRESKO TORCH FR ", "DUFLEX G FR ", "ELASTOFLEX S6 G FR ", "POLYFRESKO MOP FR ", "ELASTOSHIELD TS G FR ", heat fused or hot mopped. Class C - Fully Adhered 1. Deck: C -15/32 Incline: 2 Base Sheet: — Johns Manville "Perma Ply IV" (Type G2). Membrane: — "POLYBOND G ", " POLYFLEX G ", "POLYFRESKO TORCH FR" or "POLYFLEX G FR" (modified bitumen), heat welded. OTHER SYSTEMS 1. Deck: C -15/32 or spaced sheathing Incline: Unlimited Underlayment: — One layer Elk Corp "VersaShield ", mechanically fastened. Ply Sheet: — One ply "Polystick MTS" (self adhered). Surfacing: — Any UL Listed or Classified copper or steel standing seam panels or shingles, 26 gauge min. 2. Deck: NC Incline: Unlimited Insulation: — Any UL Classified polyisocyanurate, any thickness. Underlayment: — One ply "Polystick MTS" (self adhered). Surfacing: — Any UL Listed or Classified copper or steel standing seam panels or shingles, 26 gauge min. 1. Deck: C -15/32 MAINTENANCE AND REPAIR SYSTEMS Class A, B and C Incline: 1 Existing Roof System: — (To maintain existing Classifications) - Any Class A, B or C, uncoated, insulated or uninsulated, modified bitumen membrane or Type G3 mineral surfaced cap BUR system. Base Coat: — Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq. Top Coat: — "PolyBrite 70 ", applied at 1.5 gal. /sq. 2. Deck: C -15/32 Incline: 1 Existing Roof System: — (To maintain existing Classifications) - Any Class A, B or C, uncoated, insulated or uninsulated, modified bitumen membrane or Type G3 mineral surfaced cap BUR system. Base Coat: — Brewer "Fortress 5001 Asphalt Emulsion ", applied at 4 gal. /sq. Top Coat: — "PolyPlus 60 ", applied at V4 -1 gal. /sq. Last Updated on 2011 -02 -16 Questions? Print this page Notice of Disclaimer Page Top Copyright O 2011 Underwriters Laboratories Inc.@ The appearance of a company's name or product in this database does not in itself assure that products so identified have been manufactured under UL's Follow -Up Service. Only those products bearing the UL Mark should be considered to be Listed and covered under UL's Follow -Up Service. Always look for the Mark on the product. UL permits the reproduction of the material contained in the Online Certification Directory subject to the following conditions: 1. The Guide Information, Designs and /or Listings (files) must be presented in their entirety and in a non - misleading manner, without any manipulation http: // database. ul. com /cgi- bin/XYV /template/LISEXT /1 FRAME /showpage.html ?name =T... 3/23/2011 TGFU.R14571 - Roofing Systems Page 8 of 8 of the data (or drawings). 2. The statement "Reprinted from the Online Certifications Directory with permission from Underwriters Laboratories Inc." must appear adjacent to the extracted material. In addition, the reprinted material must Include a copyright notice In the following format: "Copyright © 2011 Underwriters Laboratories Inc.®" An independent organization working tor a sater world with integrity, precision and knowledge. http: // database. ul. com /cgi- bin/XYV /template/LISEXT /1 FRAME /showpage.html ?name =T... 3/23/2011 09 -01 -2011 City of Tukwila Jim Haggerton, Mayor Department of Community Development Jack Pace, Director PEARLLA KAESTNER PO BOX 82894 KENMORE WA 98028 RE: Permit No. D11 -079 345 ANDOVER PK E TUKW Dear Permit Holder: In reviewing our current records, the above noted permit has not received a final inspection by the City of Tukwila Building Division. Per the International Building Code, International Mechanical Code, Uniform Plumbing Code and/or the National Electric Code, every permit issued by the Building Division under the provisions of these codes shall expire by limitation and become null and void if the building or work authorized by such permit has not begun within 180 days from the issuance date of such permit, or if the building or work authorized by such permit is suspended or abandoned at any time after the work has begun for a period of 180 days. Your permit will expire on 10/25/2011. Based on the above, you are hereby advised to: 1) Call the City of Tukwila Inspection Request Line at 206 - 431 -2451 to schedule for the next or final inspection. Each inspection creates a new 180 day period, , provided the inspection shows progress. -or- 2) Submit a written request for permit extension to the Permit Center at least seven (7) days before it is due to expire. Address your extension request to the Building Official and state your reason(s) for the need to extend your permit. The Building Code does allow the Building Official to approve one extension of up to 180 days. If it is determined that your extension request is granted, you will be notified by mail. In the event you do not call for an inspection and/or receive an extension prior to 10/25/2011, your permit will become null and void and any further work on the project will require a new permit and associated fees. Thank you for your cooperation in this matter. Sincerely, c id? -------. j____ Bill Rambo Permit Technician File: Permit File No. D11 -079 6300 Southcenter Boulevard, Suite #100 • Tukwila, Washington 98188 • Phone: 206 - 431 -3670 • Fax: 206 - 431 -3665 PERM1TCOORDCOS PLAN REVIEW/ROUTING SLIP ACTIVITY NUMBER: D11 -079 DATE: 03/28/11 PROJECT NAME: SKARBOS (FORMERLY) SITE ADDRESS: 345 ANDOVER PK E X Original Plan Submittal Response to Correction Letter # Response to Incomplete Letter # Revision # after Permit Issued EPART E �S: i s V1 ding ivision I Public Works n A 1 N A tJ k 0 4 1 ' I Fire Prevention Structural n Planning Division Permit Coordinator DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete Comments: Incomplete n DUE DATE: 03/29/11 Not Applicable Permit Center Use Only INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED: Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: TUES /THURS ROUTING: Please Route 1171, Structural Review Required n REVIEWER'S INITIALS: No further Review Required ❑ DATE: APPROVALS OR CORRECTIONS: DUE DATE: 04/26/11 Approved ❑ Approved with Conditions Not Approved (attach comments) ❑ Notation: REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: Documents/routing slip.doc 2 -28 -02 Contractors or Tradespeople Pfter Friendly Page • General /Specialty Contractor A business registered as a construction contractor with L &I to perform construction work within the scope of its specialty. A General or Specialty construction Contractor must maintain a surety bond or assignment of account and carry general liability insurance. Business and Licensing Information Name ASSOCIATED ROOFING INC UBI No. 600522587 Phone 2063644445 Status Active Address P 0 Box 82894 License No. ASSOCRI16206 Suite /Apt. License Type Construction Contractor City Kenmore Effective Date 9/26/1984 State WA Expiration Date 5/6/2012 Zip 980280894 Suspend Date County King Specialty 1 General Business Type Corporation Specialty 2 Unused Parent Company Other Associated Licenses License Name Type Specialty 1 Specialty 2 Effective Date Expiration Date Status ASSOCRI164JD ASSOCIATED ROOFING INC Construction Contractor Roofing Gutters/Downspouts 4/4/1984 9/26/1984 Archived ASSOCRC21906 ASSOCIATED ROOFING COMPANY Construction Contractor Roofing Unused 9/26/1979 9/26/1984 Archived Business Owner Information Name Role Effective Date Expiration Date KAESTNER, BRYAN JAY Agent 03/29/2010 Bond Amount KAESTNER, BRYAN JAY President 10/27/2008 269250C KAESTNER, PEARLLA JO Secretary 10/27/2008 NEISINGER, WILLIAM P Agent 01/01/1980 10/27/2008 NEISINGER, NANCY Agent 01/01/1980 10/27/2008 SANDVIG, ROBERT N $12,000.0003/21 01/01/1980 01/01/1980 SANDVIG, VERDA A CCP588239 01/01/1980 01/01/1980 Bond Information Page 1 of 2 Bond Bond Company Name Bond Account Number Effective Date Expiration Date Cancel Date Impaired Date Bond Amount Received Date 7 DEVELOPERS SURETY & INDEM CO 269250C 01/08/2010 Until Cancelled $12,000.0001/19 /2010 6 DEVELOPERS SURETY & INDEMNITY 850161C 05/01/2002 Until Cancelled 02/28/2010 $12,000.0003/21 /2002 Assignment of Savings Information No records found for the previous 6 year period Insurance Information Insurance Company Name Policy Number Effective Date Expiration Date Cancel Date Impaired Date Amount Received Date 18 COMPANION SPECIALTY INS CO VGL1011152 02/20/2011 02/20/2012 $1,000,000.0002 /18/2011 17 SURETY CO CCP640664 CCP640664 02/20/2010 02/20/2011 $1,000,000.00 02/18/2010 16 CEONTURY SURETY CCP588239 02/20/2009 02/20/2010 $1,000,000.00 03/02/2009 15 CONTINENTAL CASUALTY CO 2090161787 05/01/2006 02/20/2009 $10,000,000.0004 /28/2006 14 LCEOXINGTON INS 41LX439765 05/01/2005 05/01/2006 $1,000,000.0005 /11/2005 https://fortress.wa.gov/lni/bbip/Print.aspx 04/18/2011