Loading...
HomeMy WebLinkAboutPermit M12-066 - BOEING #9-101BOEING #9 -101 9725 EAST MARGINAL WY S M12 -066 City ofTukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 -431 -3670 Inspection Request Line: 206 -431 -2451 Web site: htto: / /www.TukwilaWA.gov MECHANICAL PERMIT Parcel No.: 0003400018 Address: 9725 EAST MARGINAL WY S TUKW Project Name: BOEING #9 -101 Permit Number: M12 -066 Issue Date: 05/18/2012 Permit Expires On: 11/14/2012 Owner: Name: BOEING COMPANY THE Address: PROPERTY TAX DEPT , PO BOX 3707 M/C 20 -00 98124 Contact Person: Name: STEVE BUELER Address: 11611 49 PL W , MUKILTEO WA 98275 Email: SBUELER @UMCI.COM Contractor: Name: UNIVERSITY MECH CONTR INC Address: 11611 49 PL W , MUKILTEO WA 98275 -4255 Contractor License No: UNIVMC *343N0 Phone: 206 364 -9900 Phone: 206 364 -9900 Expiration Date: 10/03/2012 DESCRIPTION OF WORK: INSTALL VAV PACKAGED ROOFTOP UNIT, (6) FAN TERMINAL UNITS W1TH ELECTRIC REHEAT, AND (2) COOLING ONLY TERMINAL UNITS AND ASSOCIATED DUCTWORK AND GRILLES FOR TWO FLOORS OF TENANT OFFICE SPACE. ALSO INSTALL EXHAUST FAN AND ASSOCIATED DUCTWORK FOR BREAKROOM EXHAUST. Value of Mechanical: 120,000.00 Type of Fire Protection: SPRINKLERS /AFA Electrical Service Provided by: Permit Center Authorized Signature: Fees Collected: $1,514.56 International Mechanical Code Edition: 2009 Date: OS-111)112— I hereby certify that I have read and xa 'ned this permit and know the same to be true and correct. All provisions of law and ordinances governing this work will be complie •, wit , whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating construction or the performance of work. I am authorized to sign and obtain this mechanical permit and agree to the conditions on the back of this permit. Signature: &AZ Print Name: s OgeN ue This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. Date: doc: IMC -4/10 M12 -066 Printed: 05 -18 -2012 • • PERMIT CONDITIONS Permit No. M12-066 1: ** *BUILDING DEPARTMENT CONDITIONS * ** 2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the Building Official. 3: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to start of any construction. These documents shall be maintained and made available until final inspection approval is granted. 4: Insulating materials, where exposed as installed in buildings of any type of construction, shall have a flame spread index of not more than 25 and a smoke development index of not more than 450. Where facings are installed in concealed spaces in buildings of Type III, IV, or V construction, the flame spread and smoke - developed limitations do not apply to facings, that are installed behind and in substantial contact with the unexposed surface of the ceiling, wall or floor finish. 5: All construction shall be done in conformance with the approved plans and the requirements of the International Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code. 6: All plumbing and gas piping work shall be inspected and approved under a separate permit issued by the City of Tukwila Building Department (206- 431 - 3670). 7: All electrical work shall be inspected and approved under a separate permit issued by the City of Tukwila Building Department (206- 431 - 3670). 8: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the Building Official from requiring the correction of errors in the construction documents and other data. 9: ** *FIRE DEPARTMENT CONDITIONS * ** 10: The attached set of building plans have been reviewed by the Fire Prevention Bureau and are acceptable with the following concerns: 11: H.V.A.C. units rated at greater than 2,000 cfm require auto - shutdown devices. These devices shall be separately zoned in the alarm panel and local U.L. central station supervision is required. (City Ordinance #2328) 12: H.V.A.C. systems supplying air in excess of 2,000 cubic feet per minute to enclosed spaces within buildings shall be equipped with an automatic shutoff. Automatic shutoff shall be accomplished by interrupting the power source of the air- moving equipment upon detection of smoke in the main return -air duct served by such equipment. Smoke detectors shall be labeled by an approved agency for air -duct installation and shall be installed in accordance with the manufacturer's installation instructions. (IMC 606.1, 606.2.1) 13: Remote indicator lights are required on all above ceiling smoke detectors. (City Ordinance #2328) 14: Duct smoke detectors shall be capable of being reset from a single point near the alarm panel. (City Ordinance #2328) 15: Duct detectors shall send a supervisory signal only upon activation. (City Ordinance #2328) 16: All new fire'alarm systems or modifications to existing systems shall have the written approval of•*Plii Siia=Fite� Prevention Bureau. No work shall commence until a fire department permit has been obtained. (City Ordinance #2328) (IFC 104.2) ~'t7% 17: An electrical permit from the City of Tukwila Building Department Permit Center (206- 431 -3670) is required for this project. 18: All electrical work and equipment shall conform strictly to the standards of the National Electrical Code. (NFPA 70) 19: Contact The Tukwila Fire Prevention Bureau to witness all required inspections and tests. (City Ordinances #2327 and #2328) doc: IMC -4/10 M12-066 Printed: 05 -18 -2012 20: Any overlooked hazardous conilikn and /or violation of the adopted Fire or Bung Codes does not imply approval of such condition or violation. 21: These plans were reviewed by Inspector 511. If you have any questions, please call Tukwila Fire Prevention Bureau at (206)575 -4407. doc: IMC -4/10 M12 -066 Printed: 05 -18 -2012 CITY OF TUKWWA Community Development Department Permit Center 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 http://www.TukwilaWA.gov 3o2, °►1 Mechanical Permit No. Project No. Date Application Accepted: Date Application Expires: u02 —ot6n �lb 12 �o x,12 (For office use only) MECHANICAL PERMIT APPLICATION Applications and plans must be complete in order to be accepted for plan review. Applications will not be accepted through the mail or by fax. * *please print ** SITE LOCATION Site Address: Tenant Name: 9725 East Marginal Way South Boeing PROPERTY OWNER Name: Steve Bueler Name: Boeing City: Mukiltea State: WA Zip: 98275 Address: 9725 East Marginal Way South Email: sbueler @umci.com City: Seattle State: WA Zip: 98108 CONTACT PERSON — person receiving all project communication Name: Steve Bueler Address: 11611 49th Place West City: Mukiltea State: WA Zip: 98275 Phone: (206) 364 -9900 Fax: Email: sbueler @umci.com King Co Assessor's Tax No.: o00 -Neva-243 Suite Number: 9 -101 Floor: Level 1 New Tenant: ❑ Yes 121 ..No MECHANICAL CONTRACTOR INFORMATION Company Name: University Mechanical Contractors, Ir Address: 11611 49th Place West City: Mukilteo State: WA Zip: 98275 Phone: (206) 364 -9900 Fax: Contr Reg No.: UNIVMC *343N9 Exp Date: 10/03/2012 Tukwila Business License No.: $ l.I 5 ' D D O% S Z/ Valuation of project (contractor's bid price): $ /24° D o 0 Describe the scope of work in detail: Installing VAV packaged rooftop unit,six fan terminal units with electric reheat, two cooling only terminal units and associated ductwork and grilles for two floors of tenant office space. In addition, installing an exhaust fan and associated ductwork for breakroom exhaust Use: Residential: New ❑ Replacement ❑ Commercial: New Replacement ❑ Fuel Type: Electric m Gas El Other: H :'Applications \Form - Applications On Line \2011 Applications\Mechanical Permit Application Revised 8 -9 -1 I.docx Revised: August 2011 bh Page 1 of 2 Indicate type of mechanical work being installed and the quantity below: Unit Type Qty Furnace <100k btu Furnace >100k btu 1 Floor furnace 8 Suspended/wall/floor mounted heater Appliance vent Repair or addition to heat/refrig/cooling system 1 Air handling unit <10,000 cfm Unit Type Qty Air handling unit >10,000 cfm 1 Evaporator cooler 8 Ventilation fan connected to single duct Ventilation system Hood and duct 1 Incinerator — domestic Incinerator — comm/industrial Unit Type Qty Fire damper Diffuser 37 Thermostat 8 Wood/gas stove Emergency generator Other mechanical equipment 1 Boiler /Compressor Qty 0 -3 hp /100,000 btu 3 -15 hp /500,000 btu 15 -30 hp /1,000,000 btu 30 -50 hp /1,750,000 btu 50+ hp /1,750,000 btu PERMIT APPLICATION NOTES - Value of construction — in all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject to possible revision by the permit center to comply with current fee schedules. Expiration of plan review — applications for which no permit is issued within 180 days following the date of application shall expire by limitation. The building official may grant one extension of time for additional periods not to exceed 90 days each. The extension shall be requested in writing and justifiable cause demonstrated. Section 105.3.2 Intemational Building Code (current edition). I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING 0 ER 1 R AUTHORIZED AGENT: Signature: Print Name: ,f7-eve ,Petea- Mailing Address: / /// // 91 PZ-AG6 Wt 7 H.NspplicationstForms- Applications On Line\2011 ApplicationsWechanical Permit Application Revised 8 -9 -1 l.docx Revised: August 2011 bh Day Telephone: Ma /G 7Eo City Date: $ /ry -y zoG -,36 y- 9900 WA. IA 27s State Zip Page 2 of 2 • City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206-431-3665 Web site: http: / /www.TukwilaWA.gov RECEIPT ParcelNo.: 0003400018 Permit Number: M12 -066 Address: 9725 EAST MARGINAL WY S TUKW Status: APPROVED Suite No: Applied Date: 04/13/2012 Applicant: BOEING #9 -101 Issue Date: Receipt No.: R12 -01622 Initials: JEM User ID: 1165 Payment Amount: $1,211.65 Payment Date: 05/18/2012 11:09 AM Balance: $0.00 Payee: UNIVERSITY MECHANICAL CONTRACTORS, INC. TRANSACTION LIST: Type Method Descriptio Amount Payment Check 295109 1,211.65 Authorization No. ACCOUNT ITEM LIST: Description Account Code Current Pmts MECHANICAL - NONRES 000.322.102.00.00 1,211.65 Total: $1,211.65 doc: Receiot -06 Printed: 05 -18 -2012 1 City of Tukwila Department of Communi07 Development velo P ment 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206 - 431 -3670 Fax: 206-431-3665 Web site: http: / /www.TukwilaWA.gov RECEIPT ParcelNo.: 0003400018 Permit Number: M12 -066 Address: 9725 EAST MARGINAL WY S TUKW Status: PENDING Suite No: Applied Date: 04/13/2012 Applicant: BOEING #9 -101 Issue Date: Receipt No.: R12 -01310 Payment Amount: $302.91 Initials: JEM Payment Date: 04/13/2012 11:35 AM User ID: 1165 Balance: $1,211.65 Payee: UNIVERSITY MECHANICAL CONTRACTORS, INC. TRANSACTION LIST: Type Method Descriptio Amount Payment Check 302.91 302.91 Authorization No. ACCOUNT ITEM LIST: Description Account Code Current Pmts PLAN CHECK - NONRES 000.345.830 302.91 Total: $302.91 doc: Receiot -06 Printed: 04 -13 -2012 INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431 -3670 Permit Inspection Request Line (206) 431 -2451 Project: 1)-uarr. iluvief" Type of Inspection: Address: g 72-5 F4 "911 4.. Date Called: Special Instructions: V"- 7 .44/c8 -0/ Date Wanted:. ///202— // _ am p` Requester: Phone No: .2 46 - 3� r -326T5 Approved per applicable codes. Corrections required prior to approval. COMMENTS: a 1)-uarr. iluvief" v 6K- IL. 3-7- fx.0.-Ork -- • AD Inspletor: Dater 1 n REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit • INSPECTION NO PERMIT NO. CITY OF_.T,UKWILA BUILDING DIVISION 6300 southcente'r BIvd #100, Tukwila. WA 98188 ' . (206) 431 -3670! Permit Inspection: Request Line (206) 431 -2451 M-i2 -oo, Proj ct: .. /5G3`�'^ k l � O I Type of Inspec ion: �C,�i , U DC -�' Address :'Date 4 7 L- 6 .'Af, Called: _ Special Instructions::, - . Date Wanted:. , `a_m__. Ico -r --r2_ p.m. Requester: Phone Le ^ 1 ( -^ 32_ Approved per,applicable codes. 'Corrections required prior to approval. COMMENTS: J A —pk©r< i '1 Inspector: Date: O REINSPECTION'FEE REQUIRE . Prior to next inspection. fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. _ INSPECTION RECORD. Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING D IVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 oz. (206) 431.3670 Permit Inspection Request Line (206) 431 -2451 Pro ct: 4 6d -� A<o c( ---1 0 4 Type /o ofpInspection: __ M. o;c. ,S Addr�s5' "� 23. 1 ` ��/i' t0. /lid Date Called: Special Instructions: Date Wanted• . /_ f`a .. Requester: ~' Phone No: / ElApproved per applicable codes. COMMENTS: Corrections required prior . to; approval. e & M. r Are ,&re.sl- F r -For -TL, :..5 . c, t o r- f I`e. 744- c mom- o iuk : ,f-r- JP .M v A t C ft 2 E F r C F CeS5 c '24.D as O Inspector: Date:. n REINSPECTION FEE REQUIRED. Prior to next inspection fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. • INSPECTIO NO. INSPECTION RECORD Retain a copy with permit • .PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 431 -2451 Project: /30£2A/6 ,°'" - /0/ Type of Inspection: /.20/6. Address: i %.Z..5 F 4 S r pi /9 2cTn/9l Date Called: Special Instructions: Date Wanted: .1 Requester: Phone No: - 0 Approved per applicable codes. Corrections required prior to approval. pik Z, -ter t,31 COMMENTS: ,orY,PiT i'J A D( -ef`AJ 0 6-0 LA ACt'ir Inspettor: Date REINSPECTION FEE REQUIRED. Prior to next inspection, fee must, be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection,. INSPECTION RECORD Retain a copy with permit INSPECTIO NO. . ; PERMIT.NO. C TY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila: WA 98188 Q... -- ':(206) 431 -3670 Permit Inspection Request Line (206) 431 -2451 Project :. /30d0,16 9- 10 / Type of Inspection•,`; ,,..?o/9h- Address: , c/ 72 S c s -n142e v9L Date Called: • Special Instructions: Date Wanted: 9— /0 4Z, , _ a.m. pra Requester: Phone No: 0 Approved per applicable codes. Corrections required prior to approval. COMMENTS: /14-® S Lvi-e° - )//' 7/9€ r nspecrr. 1A n REINSPECTION FE REQUIRED. Prior to next inspection fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection: `INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd:,1 #100, Tukwila. WA 98188 I` (206) 431 -3670 Permit- lnspection.Re quest Line (206) 431 -2451 Project G Type of Ins ,/ Address: 2A-7 Date Called: Special Instructions; Date Wante d:. am, e °a�— /2_ p.m. Requester: Phone N°206 r� ,3,J 3z G Approved per applicable codes. COMMENTS:_. ,04 Corrections required prior to approval. !` ate- e, J,-7J REINSPECTION.FEE RE IRED. Pr r to next inspection. fee must be paid at 6300'Southcente Blvd.. Suite 100. Call to schedule reinspection. INSPECTION RECORD. Retain a copy with permit INSPECTION NO. : PERMIT NO. CITY OF TUKWILA BUILDING. DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431.- 3670. Permit Inspection Request Line (206) 431 -2451 Project: ,30,E r/vb z' 90 Type of Inspection: Address: 7_25 Fos T rorma--Nitt Date Called: r,...“, s : is Special Instructions: Date Wanted: 6 -2o -r Z . • -a'm pm. Requester: i Phone No: ,26l -39J _ .,5',' .t. ❑ Approved per applicable codes. [54 Corrections requiredeprior to approval COMMENTS: /TrAJd.h dc, ti 4— J n REINSPECTION FEE REQUIRED. Prior to next inspection; fee must ,be °- paid at 6300 Southcen er Blvd., Suite 100. Call to schedule:reinspection :: INSPECTION NO. INSPECTION RECORD Retain a copy with permit PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 :'' : (206) 431 -3670 Permit Inspection Request Line (206) 431 -2451 Project: _ t� Type of Inspection :, Address: CtiI%c re;• Special Instructions: 9- e tZ (24\ 4e.,y{' dda f ti p P €.r& i` A er STi r . 4-t- ElApproved per applicable codes. COMMENTS: Date Called: Date Wanted: •;�rri. p.m. Requester: Phone No: l�lo — Corrections required_ prior to approval.. n : REINSPECTION FEE REQUIRED. Prior to next inspection fee mustbe' paid at 6300 Southcenter Blvd., Suite 100. Call to sche,dule,reinspection: Date: INSPECTION NUMBER INSPECTION RECORD Retain a copy with permit f /(9- r- (95r 133 3 toos...(0.6.haf PERMIT NUMBERS CITY OF TUKWILA FIRE DEPARTMENT 444 Andover Park East, Tukwila, Wa. 98188 206- 575 -4407 Project: n � �' Sprinklers: Fire Alarm: Ty e of Ispectlion: 4 fv►iic c, r� - �,'NAL Address: 'i'7 0 Suite #: `i- /� / N► 2_ ., Contact Person: Special Instructions: Phone No.: MApproved per applicable codes. Corrections required prior to approval. COMMENTS: Needs Shift Inspection: Sprinklers: Fire Alarm: Hood & Duct: Monitor: Pre -Fire: Permits: Occupancy Type: Inspector: / 0/-‘ S` d— Date: //2 -// Z Hrs.: $100.00 REINSPECTION FEE REQUIRED. You will receive an invoice from he City of Tukwila Finance Department. Call to schedule a reinspection. Billing Address Attn: Company Name: Address: City: State: Word /Inspection Record Form.Doc 6/11/10 T.F.D. Form F.P. 113 REV CODE CAL APPROVED 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Mechanical Summary MECH -SUM 2009 Washington State Energy Code Compliance Forms for Nonresidemial and Multifamily Residential Revised February 2011 Project Info ILE COPY _ Project Address Boeing Building 9101 Date 12/12/2011 9725 E Marginal Way s For Building Dept. Use • Tukwila, WA 98108 Applicant Name: STEVE BUELER Applicant Address: 11611 49TH PLACE WEST MUKILTEO, WA Applicant Phone: 208.388.6985 Project Briefly describe system type Description mechanical and features. Plans Installing VAV package rooftop unit, six fan terminal units with reheat coils, two cooling only terminal units and associated ductwork for two floors of tenant office space. In addition, installing an exhaust fan and associated ductwork for break room exhaust Drawings must contain notes requireing compliance with commissioning requirements - Section 1416 Indudes Compliance Option 0 Simple System ® Complex System 0 Systems Analysis (See Decision Flowchart (over) for qualifications. Use separate MECH -SUM for simple & complex Equipment Schedules The following information is required to be incorporated with the mechanical equipment schedules on the plans. For projects without plans, fill in the required information below. Cooling Equipment Schedule Equip. ID Equip Type Brand Name' Model No.' Capacity' Btu/h OSA CFM or Econo? SEER or EER IPLV3 Econmizer Option or Exceptions Heat Recovery WN SRS 03 AND G4 FOR EQUIPItENT! SCHEDULES Heating Equipment Schedule Equip. ID Equip Type Brand Name' Model No.' Capacity' Btu/h OSA cfm or Econo? Input Btuh Output Btuh Efficiency` Heat Recovery Y/N 8IE G3 AND G4 FOR EQUIPMENT SCHEDULES Fan Equipment Schedule Equip. ID Equip Type Brand Name' Model No.' CFM Sp' HP /BHP Flow Controls Location of Service SEE 03 AND 04 FOR EQUIP)NT SCHEDULES MAY 11 2012 City of Tukwila BUILDING DIVISION according to Table 14 -1A through 14 -1G. 3 If required. 4 COP, HSPF, Combustion Efficiency, or AFUE, as •es: variable air volume(VAV), constant volume (CV), or variable speed (VS). 6 Exception number from CITY �� ' ' LA APR '13 2012 PERMRCENTER AA] Tim. OW0 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Mechanical Summary (back) MECH -SUM 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Revised February 2011 System Description See Section 1421 for full description of Simple System qualifications. All Systems: ❑ No humidification? ❑ No Reheat? If Heating/Cooling or Cooling Only: ❑ Constant vol? ❑ Split system? ❑ <= 84,000 Btuh? ❑ Economizer ❑ Air cooled? ❑ Packaged sys? ❑ <= 135,00 "BtIJh ?' ' -,-) -i ❑ Cooling Cap < =15 Btuh/ft2? - ❑ Heating Cap. > 0 & < =10 Bti f /ftz. ?' If Heating Only: <1000 cfm? < Btuh/ft2? ❑ ❑ 30 %outside air? Heating Cap. < =10 Btuh /h � Decision Flowchart Use this flowchart to determine if project qualifies for Simple System Option. If not, either the Complex System or Systems Analysis Options must be used. ( START ) C Yes Humidification or Reheat? System Type Heating/Cooling or Cooling Only Air Cooled, onstant Volu Heating Only Reference Section 1421 <1000 Yes Total CFM Serving Single Roo <30% OSA Package Unit Cap <= 135,000 Btuh Yes Split System <= 84,000 Btuh Yes Yes eatin Cap <= 10 to Yes= -N Yes • Simple System Allowed (section 1420) alifies Economizer Exception ion l•- Yes ol,Use Complex Systems (section 1430) 'Complex Systems I Refer to MECH -COMP Mechanical Complex Systems for assistance in determining which Complex Systems requirements are applicable to this project. • es' 6 GIN4140 t to 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Mechanical - Complex Systems Checklist MECH Code Compliance Forms for Nonresidential and Multifamily Residential -COMP 2009 Washington State Energy Revised February 2011 Project Address Boeing Building 9 -101 Date 12/12/2011 The following additional information is necessary to check a mechanical permit application for a complex mechanical system for compliance with the mechanical requirements in the Washington State Nonresidential Energy Code. Use the checklist as a reference for notes added to the mechanical drawings (see the MECH -CHK checklist for additional requirements). This information must be on the plans since this is the official record of the permit. Having this information in separate specifications alone is NOT an acceptable altemative. For Building Department Use Applicability (yes, no, na) Code Section Component Information Required Location on Plans Building Department Notes ADDITIONAL CHECKLIST ITEMS FOR COMPLEX SYSTEMS ONLY Yes 1431.1 Field assem. sys. Provide calculations for total onsite energy input/output to equip. G3 Yes 1431.2 System Sizing Indicate equipment & system sizing complies with 1431.2 G2&G3 Yes 1432.1 Setback & shut -off Indicate separate systems or show isolation devices on plans M21i AND 14221 Yes 1432.2.1 Air system reset Indicate automatic temperature reset & operation sequence G2 Yes 1432.2.2 Hydr. Sys. reset Indicate automatic temperature reset & operation sequence G2 N.A. 1432.3.1 Hydr. Var. Flow Indicate variable flow method for all applicable systems N.A. 1432.3.X Hydronic Isolation Indicate method of isolation for all applicable systems Yes 1432.4 DDC Capabilities Indicate control capabilities including demand response setpoind adj. G2 &G3 Yes 1432.4 DDC data mgmt Indicate metering and trending capabilities. G2 Yes 1432.5 Pressure Reset Indicate static pressure reset for VAV systems G3 Yea 1433 Air Economizer Indicate economizer on equipment schedule or provide calculations to justify exemption. Demonstrate higher efficiency equipment if required. G3 • N.A. 1433 Water Economizer Indicate water economizer and provide calculations showing compliance with 1413 if 1433 Exception 3 is utilized N.A. 1434 Separate air sys. Indicate special requirement zones and indicate systems Yes 1435 Simul. htg. & clg. Indicate method of prohibiting simultaneous heating and cooling, or state excpetion and show supporting calculations G2 N.A. 1436 Heat recovery Indicate heat recovery of all applicable systems on plans; complete and attach heat recovery calculations Yes 1437 Elec. motor effic. MECH -MOT or Equip. Schedule with hp, rpm, efficiency G4 N.A. 1438 Variable speed drives Indicate VS control or equivalent on schedules for all applicable equip. G3 N.A. 1438.1 Heat Rejection Indicate heat rejection equipment types and fan types N.A. 1438.2 Hot Gas Bypass Indicate cooling equipment staging and capacity modulation abilities N.A. 1438.3 Large Volume sys Indicate multiple system rooms & indicate ventilation control N.A. 1439.1 Kitchen Hoods Indicate source and conditioning of make -up air , N.A. 1439.2 Laboratory Exhaust Indicate HR, VAV, semi - conditioned makeup, or CERM calc no is circiea for any question, proviae explanation: Decision Flowchart (Start Here Section 1411.1 Equipment Efficiency Shall Meet Tables 14 -1A through 14 -1G s/Oil Furna input? 225,000 uh or Any U eate IUse flowchart to determine how the requirements of the Complex Systems Option apply to the project. Refer to the indicated Code sections for complete information on the requirements. Yes Air System Serving Multiple Zones? 1411.1 IID & Power Venting or Damper. If input ? 225,000 Btuh then 1412.6 Modulating Controls Required Yes Section 1411.1 0.75% Maximum Jacket Loss Yes Section 1412.8 Ventilation Controls for High - Occupancy Areas Yes Section 1431.1 Calculations of Total On -Site Energy Input & Ouput Required (continued on back) Yes Section 1432.2.1 Supply Air Reset Controls Required Ye* 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Mechanical - Complex Systems (back) MECH -COMP 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Revised February 2011 Section 1432.3.2 through 1432.3.5 Device Isolation Required Section 1432.3.1 Variable Flow Design Required dronic Syste Heated or Cooled 300,000 Btu Section 1432.4 DDC Required With Trending and Demand Response Section 1436.1 50% Effective Heat Recovery Required Section 1436.2 Condensate Recovery Required 4 Hour Ops, ter Cooled Conden tuh, & Sery OkB Section 1436.3 Condenser Heat Recovery Required Section 1436.4 Refrigeration Condenser Heat Recovery Required ystem or Zone w/ Simultaneous tg. & Clg.? Section 1435 Zone Controls Must Reduce Supply Air Quantity Before Reheating/Recooling ystem o ystems serving a room have 10,000 CF pp Section 1438.3 Controls Must Reduce Airflow When System In Not Heating or Cooling Section 1438 Variable Flow Devices Required otor Incl. in Eqpmt. Covr'd by Tbl 14- 1A -14- 16? Multi -speed Motor in Multi - eed system Yes* Section 1432.2.2 Water Temperature Reset Required No• Section 1437 Motors Must Meet Efficiencies in Table 14-4 Yes No No DONE Section 1439.1 No Heating or Cooling for at Least 50% of Make -up Air Yes Ye • Section 1439.2 One Required: a. Heat Recovery per 1439.2 b. 50% VAV Exhaust & Make -up c. 75% Direct Makeup w/ Tempering Only d. Combined Energy Reduction Oer> =omin Yes 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Economizer MECH -ECO 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Revised February 2011 Economizer Summary Check box(es).for exceptions being claimed. List the system /equipment that qualifies for each exception. See Section 1433 for full description of Economizer requirements. 4 Full Air Econo: ACU -1 Ex 1: ❑ Ex 5: ❑ Ex 9a: ❑ Ex 2: ❑ Ex 6: ❑ Ex 9b: ❑ Ex 3: ❑ Ex 7: ❑ Ex 9c: 0 Ex4: ❑ .1 Ex10: Decision Flowchart Ex B. Use this flowchart to determine if project complies with Economizer requirements. If not, the Systems Analysis Option must be used. ( START Yes Reference Section 1433 Group R Occ. ception 8: Unit Cap <20,000 Btuh e Full Air Economizer - Complies ception it Cap <54,000 B it not Exterior 'ace No ception . it Cap < 33,000 B nit not Exterior o djacen :Idg. Cap. w/o economizer <72,000 Btuh or 5 %? Exception 2: Chilled Water Sys. ' er 25% over • Yes Idg Cap wo Econ - 80,000 Btu or 2 ptio er Cooled Re . terside Economiz ing chiiled b Sys No No V ception 3 Syste Cap. <= 500 tons es No Exception 4: Cooling 75% Site HR or Solar Exception 5: Special OA iltration Need ception •. Dehumidification with supporting rgy ana • Exception 7: Heat Pump Loop eting All Crit No No ception 9: Dedicated Server or Eq Rm rved b 14 -1A or 14-1B quipme xc. 9a: EER & IPLV °• Over e Ye No ception 10: RF System Meeting All Criteria c. RAE 127 is 14- 1A/14- /IP xc. 9 • . Water Econo ER & IPL 5% • ode Ye P- L ote C or belt f cap >85,00 tu Yes No No Does Not Comply Qualifies for Full Air Economizer Exception - Complies • 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Electric Motors MECH -MOT 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Revised February 2011 Project Address Boeing Building 9 -101 Date 12/12/2011 Complete the following for all design A & B squirrel -cage, T -frame induction permanently wired polyphase motors of 1 hp or more having synchronous speeds of 3600, 1800 or 1200 rpm (unless one of the exceptions below applies). For Building Department Use Motor No. or Location HP Type (open /closed) Description of Application or Use Synch. Speed Min.Nom. Full load Efficiency SEE 63 AND GC Ifni rvrr Nominal Fad -Laad Eff d en ies t%) As of 12)1912010 Exceptions: 1. Motors in systems designed to use more than one speed of a multi -speed motor. 2. Motors already included in the efficiency requirements for HVAC equipment (Tables 14- 1A or 14-1B) . 3. Motors that are an integral part (i.e. not easily removed and replaced) of specialized process equipment (i.e. equipment which requires a special motor, such as an explosion - proof motor). 4. Motors integral to a listed piece of equipment for which no qualifying motor has been approved (i.e. if the only U.L. listing for the equipment is with a less- efficient motor and there is no energy- efficient motor option). For motors claiming an exception, list motor and note which exception applies. Open Motors Enclosed Motors Synchronous Speed (RPM) 3,600 1600 1,200 3,600 1,800 1,200 Motor H P 1.0 77.0 85.5 82.5 77.0 85.5 82.5 1.5 84.0 86.5 86.5 84.0 86.5 87.5 2.0 85.5 86.5 87.5 85.5 86.5 88.5 3.0 85.5 89.5 88.5 86,5 89 5 8g 5 5.0 86.5 89.5 89.5 88.5 89.5 89.5 7.5 88.5 91.0 90.2 89.5 91.7 91.0 10.0 89.5 91.7 91.7 90.2 91.7 91.0 15.0 90.2 93.0 91.7 91.0 92.4 91.7 20.0 91.0 93.0 92.4 91.0 93.0 91.7 25.0 91.7 93.6 93.0 91.7 93.6 93.0 30.0 91.7 94.1 93.6 91.7 93.6 93.0 40.0 92.4 94.1 94.1 92.4 94.1 94.1 50.0 93.0 94.5 94.1 93.0 94.5 94.1 60.0 93.6 95.0 94.5 93.6 95.0 94.5 75.0 93.6 95.0 94.5 93.6 95.4 95.4 100.0 93.6 95.4 95.0 94.1 95.4 95.0 125.0 94.1 95.4 95.0 95.0 95.4 95.0 150.0 94.1 95.8 95.4 95.0 95.8 95.8 200.0 95.0 95.8 95.4 95.4 96.2 95.8 250.0 95.0 95.8 95.4 95.8 96.2 95.8 300.0 95.4 95.8 95.4 95.8 96.2 95.8 350.0 95.4 95.8 95.4 95.8 96.2 95.8 4110.0 95.8 95.8 95.8 95.8 96.2 95.8 450.0 95.8 96.2 96.2 95.8 96.2 95.8 500.0 95.8 962 96.2 95.8 96.2 95.8 ,r 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Mechanical Permit Plans State Energy Code Compliance Forms Checklist MECH for Nonresidential and Multifamily Residential -CHK 2009 Washington Revised February 2011 Project Address Boeing Building 9 -101 (Date 12/12/2011 The following information is necessary to check a mechanical permit application for compliance with the mechanical requirements in the Washington State Nonresidential Energy Code. Applicability (yes, no, na) Code I Section 'Component Information Required Location on Plans Building Department Notes HVAC REQUIREMENTS (Sections 1401 -1424) 1411 Equipment Performance Yea 1411.1 Minimum efficiency Equipment schedule with type, capacity, efficiency G3 N.A. 1411.1 Combustion htg. Indicate intermittent ignition, flue /draft damper & jacket loss N.A. 1411.1 Air - cooled chiller Provide total air and water chiller capacity N.A. 1411.2.1 Water - cooled chiller Full -load and NPLV values adjusted for any non - standard conditions N.A. 1411.4 Pkg. elec. htg.& clg. List heat pumps on schedule N.A. 1411.5 Unenclosed Heat Indicate radiant heat system and occupancy controls 1412 HVAC Controls Yes 1412.1 Temperature zones Indicate locations on plans M211 Yee 1412.2 Deadband control Indicate 5 degree deadband minimum G2 N.A. 1412.3 Humidity control Indicate humidistat Yes 1412.4 Setback and Shutoff Indicate thermostat with 7 day program capability & required setback G2 Yes 1412.4.1 Dampers Indicate damper location, leakage rate, control type, & max. leakage 2421i Yes 1412.4.2 Optimum Start Indicate optimum start controls G2 N.A. 1412.5 Heat pump control Indicate heat pump thermostant & outdoor lockout on schedule N.A. 1412.6 Combustion heating Indicate modulating or staged control Yea 1412.7 Balancing Indicate balancing features on plans 99211 Yes 1412.8 Ventilation Control Indicate demand control ventilation for high - occupancy areas M211 N.A. 1412.9 Loading Dock & Garage Ventilation Indicate enclosed loading dock & parking garage ventilation system activation and control method. Yea 1422 Thermostat interlock Indicate thermostat interlock on plans M211 Yes 1432.2.1 Temperature Reset Indicate temperature reset method G2 1413 Air / Water Economizers N.A. 1412.1 Single zone systems Indicate multiple cooling stage control capability. N.A. 1413.1 Air Econo Operation Indicate 100% capability on schedule N.A. 1413.1 Wtr Econo Operation Indicate 100% capacity at 45 degF db & 40 deg F wb N.A. 1413.2 Wtr Econo Document Indicate max. OSA condition for design clg load & equipment performance data. Yea 1413.3 Integrated operation Indicate capability for partial cooling M1.1 N.A. 1413.4 Humidification Indicate direct evap or fog atomization w/ air economizer 1414 Ducting Systems Yes 1414.1 Duct sealing Indicate duct design pressures, sealing, and testing requirements G2 Yes 1414.1.2 Low press. duct test Indicate applicable low pressure duct systems shall be leak tested G2 Yea 1414.1.3 High press. duct test Indicate high pressure duct systems shall be leak tested, and identify the location of this ductwork on plans G2 Yes 1414.2 Duct insulation Indicate R -value of insulation on duct G4 1415 Piping Systems N.A. _ 1415.1 Piping insulation Indicate R -value of insulation on piping 1416 Completion Requirements Yes 1416.3.2 System Balancing Indicate air and water system balancing requirements G2, Yea 1416.3.3 Functional Testing Provide sequence of operations and test procedures. G2 Yes 1416.3.4 Documentation Indicate O &M manuals, record drawings, staff training G2 Yes 1416.3.5 Comm. Report Indicate requirements for final commissioning report G2 Yea 1416.4 Compliance Chkiist Submit to building official upon substantial completion. G2 Yes (Mechanical Summary Form 1 Completed and attached. Equipment schedule with types, input/output, efficiency, cfm, hp, economizer I 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Mechanical Permit Plans Checklist Continued MECH -CHK 2009 Washington State Energy Code Compliance Forms for Nonresidential and Multifamily Residential Revised February 2011 Project Address Boeing Building 9 -101 (Date 12/12/2011 The following information is necessary to check a mechanical permit application for compliance with the mechanical requirements in the Washington State Nonresidential Energy Code. Applicability Code (Yes, no, na) I Section (Component (Information Required Location on Plans Building Department Notes SERVICE WATER HEATING AND HEATED POOLS (Sections 1440 -1454) 1440 Service water htg. N.A. 1441 Elec. water heater Indicate R -10 insulation under tank N.A. 1442 Shut -off controls Indicate automatic shut -off of circulators or heat. trace N.A. 1443 Pipe Insulation Indicate R -value of insulation on piping N.A. 1444 Pump Energy Indicate method of pump energy management (Sec 1438) N.A. 1445 Heat Recovery Indicate preheat capacity as % of peak service water demand. 1460 Heated Pools N.A. 1452 , Heat Pump COP Indicate minimum COP of 4.0 N.A. 1452 Heater Efficiency Indicate pool heater efficiency N.A. 1453 Pool heater controls Indicate switch and 65 degree control N.A. 1454 Pool covers Indicate vapor retardant cover N.A. 1454 Pools 90+ degrees Indicate R -12 pool cover N.A. 1455 Heat Recovery Indicate method and capacity of exhaust air temperature reduction COLD STORAGE (Sections 1460-1465) 1460 Cold Storage N.A. 1463 Evaporators Indicate motor type and speed control N.A. 1464 Condensors Indicate condenser cooling type, design wb temp and control N.A. 1465 Compressors Indicate design minimum condensing temp and control. If "no" is Indicated for any Item in Sections 1401 -1424 or 1440 -1465 , provide explanation: *IPPERMITCOORDCOPO PLAN REVIEW/ROUTING SLIP ACTIVITY NUMBER: M12 -066 DATE: 04/13/12 PROJECT NAME: BOEING #9 -101 SITE ADDRESS: 9725 EAST MARGINAL WY S X Original Plan Submittal Response to Incomplete Letter # Response to Correction Letter # Revision # after Permit Issued DEPARTMENTS: building Division TiC1-1;,) AtA Fire Prey ntion 1 Planning Division Public Works ❑ Structural Permit Coordinator DETERMINATION OF COMPLETENESS: (Tues., Thurs.) Complete DUE DATE: 04 /17/12 Incomplete ❑ Not Applicable E. Comments: Permit Center Use Only INCOMPLETE LETTER MAILED: LETTER OF COMPLETENESS MAILED: Departments determined incomplete: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: TUES /THURS ROUTING: Please Route Structural Review Required ❑ No further Review Required ❑ REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: DUE DATE: 05/15/12 Approved ❑ Approved with Conditions 14W Not Approved (attach comments) Notation: REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: Documents /routing slip.doc 02/29/12 Contractors or Tradespeop''ter Friendly Page General /Specialty Contractor A business registered as a construction contractor with L &I to perform construction work within the scope of its specialty. A General or Specialty construction Contractor must maintain a surety bond or assignment of account and carry general liability insurance. Business and Licensing Information Name UNIVERSITY MECH CONTR INC UBI No. 578025176 Phone 2063649900 Status Active Address 11611 49Th Pi W License No. UNIVMC'343N9 Suite /Apt. License Type Construction Contractor City Mukilteo Effective Date 8/29/1966 State WA Expiration Date 10/3/2012 Zip 982754255 Suspend Date County Snohomish Specialty 1 General Business Type Corporation Specialty 2 Unused Parent Company Other Associated Licenses License Name Type Specialty 1 Specialty 2 Effective Date Expiration Date Status GRANSML982R3 GRANSTON MECHANICAL LLC Construction Contractor General Unused 12/23/2002 1/8/2009 Expired Business Owner Information Name Role Effective Date Expiration Date BUSH, GERALD D President 03/13/2002 Bond Amount GRANSTON, EDWARD B Secretary 03/13/2002 08965196 PETTERSON, DEAN M Treasurer 03/13/2002 SMITH, DOUG Vice President 03/18/2002 TRAVELERS CAS & SURETY CO KOMMERS, EDWARD D Vice President 03/13/2002 09/13/2004 BALDWIN, TERRY L Vice President 03/13/2002 09/10/2003 GRANSTON, FRANK Treasurer 03/18/2002 12/23/2002 Bond Information Page 1 of 2 Bond Bond Company Name Bond Account Number Effective Date Expiration Date Cancel Date Impaired Date Bond Amount Received Date 7 FIDELITY Et DEPOSIT CO OF MD 08965196 07/31/2009 Until Cancelled $12,000.0006/04 /2009 6 TRAVELERS CAS & SURETY CO 103335164 07/22/2001 Until Cancelled 07/31/2009 $12,000.00 10/03 /2001 Assignment of Savings Information No records found for the previous 6 year period Insurance Information Insurance Company Name Policy Number Effective Date Expiration Date Cancel Date Impaired Date Amount Received Date 31 Phoenix Insurance Company, The DTC0526D8270PHX11 06/01/2011 06/01/2013 $1,000,000.00 05/01/2012 30 THE PHOENIX INS CO C0526D8270PHX10 10/01/2010 10/01/2011 $1,000,000.00 09/22/2010 29 PHOENIX INS CO C0526D8270PHX09 10/01/2009 10/01/2010 $1,000,000.00 09/22/2009 28 TRAVELERS PROPERTY CAS INS CO DTE0526D8270TIL07 10/01/2007 10/01/2009 51,000,000.00 09/19/2008 27 TRAVELERS PROPERTY CAS INS CO DTEC0526D8270TIK07 10/01/2007 10/01/2008 $250,000.00 09/21/2007 https: // fortress .wa.gov /lni /bbip /Print.aspx 05/18/2012 1:48 PM f: \acad \engineering \5761 \sheets \gO.dwg N N STEVE BUELER VICINITY/ SITE MAP PARCEL INFORMATION PARCEL # 0003400018 LEGAL DESCRIPTION: GROW TIMOTHY -D C # 44 Sc 48 POR OF DC & DUWAMISH RIVER AS ESTAB BY CWW # 1 & SLIP # 7 & VAC CO RD & VAC S 98TH ST DAF BEG 2222.8 FT W & 654.72 FT N OF SE COR OF DC TH S TAP 379.11 FT N OF S LN OF DC EXT W TH E TO E MGN VAC CO RD #57 TH S 89 -54 -40 E 298.36 FT TH N 73 FT TH S 89 -54 -40 E 397.60 FT TO WLY MGN E MARGINAL WAY TH NWLY ALG SD MGN TO C/L VAC S 98TH ST TH SWLY & WLY ALG SD C/L TO ELY LN SLIP #7 TH N 13 -58 -30 W TO NLY LN SD SLIP TH WLY ALG SD NLY LN TO ELY LN CWW #1 TH SLY ALG SD ELY LN TAP N 89 -08 -00 W OF BEG TH S 89 -08 -00 E 1352.06 FT M/L TO BEG & POR BEG 2222.8 FT W & 654.72 FT N OF SE COR OF DC TH S TO MDR LN OF DUWAMISH RIVER TH N 74 -29 -52 W 466.63 FT TH S 70 -07 -00 W 489.88 FT TH N 43 -00 -00 W 299.88 FT TH N 29 -00 -00 W 562.76 FT TH S 89 -11 -40 E TO BEG LESS PSH #1 SCOPE OF WORK PROVIDE APPROXIMATELY 4,100 SF MODULAR OFFICE SPACE TO SUPPORT "BTE" TEST AREA. PROJECT INCLUDES MODULAR BUILDING SHELL, INTERIORS & ALL SUPPORTING UTILITIES WITH CONNECTIONS TO EXISTING BUILDING SUPPLY SOURCES. DUCT LINE EQUIVALENTS LEGEND SINGLE LINE X V Z IX I 1I F c 1 IRECT -i ROUND ROUND �-� ROUND —�-- DOUBLE LINE DESCRIPTION 90' ELBOW UP (SUPPLY) 90' ELBOW UP (RETURN /EXHAUST) 90' ELBOW DOWN (SUPPLY) 90' ELBOW DOWN (RETURN /EXHAUST) RADIUS ELBOW UP (SUPPLY) RADIUS ELBOW UP (RETURN /EXHAUST) RADIUS ELBOW DOWN (SUPPLY) RADIUS ELBOW DOWN (RETURN /EXHAUST) ROUND DUCT UP (S /R /E) ROUND DUCT DOWN (S /R /E) ®i11111111` cani cal=i1 TURNING VANE ELBOW RADIUS ELBOW, RECT RADIUS ELBOW, ROUND 4:13===1 TRANSITION (ROUND TO ROUND/ RECTANGULAR TO RECTANGULAR) 1 RECT ROUND RECT RECT -�— ROUND -111"" TRANSITION (RECTANGULAR TO ROUND) SPIN -IN TAKEOFF CONICAL TEE TEE WITH TURNING VANES BRANCH TAKEOFF, RECT BRANCH TAKEOFF, ROUND BRANCH TEE, RECT CONICAL SPIN -IN TAKEOFF MECHANICAL INDEX OF DRAWINGS MECHANICAL SHEET 1 GO G1 G2 G3 G4 DESCRti TION DRAWING INDEX, SYMBOLS, & SITE PLAN SYMBOLS, GENERAL NOTES, & ABBREVIATIONS SEQUENCE OF OPERATION, LOAD SUMMARY MECHANICAL SCHEDULES MECHANICAL SCHEDULES M211 HVAC PLAN - LEVEL 1 M21i HVAC PLAN - LOWER LEVEL INTERSTITIAL M22i HVAC PLAN - UPPER LEVEL INTERSTITIAL M221 HVAC PLAN - LEVEL 2 M230 HVAC PLAN - ROOF LEVEL M301 MECHANICAL DETAILS M302 MECHANICAL ELEVATION VIEW M303 MECHANICAL ELEVATION VIEW _REVISIONS —.-1 No changes shall made to the scope of Ivork witho }:j pw'cr approval of 1 Tukwila Eau: ping Division. I r ^visions will rc:quiro a new plan I , '� J may include add #ional plan rev wfcc ; I SCALE N/A N/A N/A N/A N/A 1/4" = 1' -0" 1/4" = 1' -0" 1/4" = 1' -O" 1/4" = 1' -O" 1/4" = 1' -O" N/A N/A N/A DUCT LINE EQUIVALENTS LEGEND SINGLE LINE DOUBLE LINE DESCRIPTION R - 1- -+-- -� 1 R 1 FSD I T FD MOD BDD 1 BDD EF —X O 10 200 0 T= . B =. BOOT TEE 45' LATERAL 45' CONICAL LATERAL ELEVATION CHANGE RISE (R) OR DROP (D) AIR FLOW DIRECTION - SUPPLY AIR FLOW DIRECTION - RETURN OR EXHAUST DUCT END CAP FLEXIBLE DUCTWORK MANUAL VOLUME DAMPER REMOTE VOLUME DAMPER FIRE /SMOKE DAMPER - PROVIDE ACCESS FIRE DAMPER - PROVIDE ACCESS MOTOR OPERATED DAMPER BACKDRAFT DAMPER HUMIDIFIER WALL MOUNTED TSTAT WITH CONTROL LINE SUPPLY DIFFUSER SUPPLY GRILLE RETURN /EXHAUST GRILLE EQUIPMENT MARK DIFFUSER /GRILLE DESIGNATION ROUND DUCT TOP OF DUCT, BOTTOM OF DUCT Peraiil No. Pier rrvi3W approval is subject to errors and omissions. of construction documents does not authorize G4 any adopted code or ordinance. Receipt n; pp ;Qved Field Copy and I is acknowledged: By Date:... g 12 City Of Tukwila BUILDING DIVISION REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11 2012 VV� City of Tukwila BUILDING DIVISION SYM A REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE PERMIT PLANS UMC 04/13/12 ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED APPROVED BY DEPT. DATE DRAWN UMC CHECKED ENGINEER MSH DATE 03 -14 -12 SUBTITLE M #.668.0(0(0 CURRENT REVISION DRAWING INDEX, SYMBOLS, & SITE PLAN SEPARATE PERMIT REQUIRED FOR: ❑ Mechanical ectrical lumbing s Piping City of Tukwila FJUUJ NG DIVISION CITY ORIMLA APR 1 9 2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SYMBOL A DATE 03 -14 -2012 CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9 -101 BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET GO JOB NO. COMP NO. DWG NO. 9- 101 —GO 1:48 PM f: \acad \engineering \5761 \sheets \g1.dwg N N STEVE BUELER GENERAL SYMBOL C --r X —I F— qOP XX' —XX" ) 1 E c ABBR DESCRIPTION 45 45 DOWN 90 AD ACCESS DOOR IN CEILING AD ACCESS DOOR IN WALL ALIGNMENT GUIDE ANCHOR AUTOMATIC CONTOL VALVE (3 -WAY) AUTOMATIC CONTROL VALVE (2 -WAY) BALANCING VALVE BV BALL VALVE BOP BOTTOM OF PIPE ELEVATION BREAK BFV BUTTERFLY VALVE CAP CENTERLINE CL -EL CENTERLINE OF PIPE ELEVATION CHK CHECK VALVE CIRCUIT SETTER DETAIL TAG DN DOWN ELEVATION TAG FLOW ARROW GENERAL SYMBOL �E XX' —XX" ) PITCH F R FOOT ( PITCH ),pc PER FOOT — (-(-1 -- 101 14-1 xxxxxxxxx tf)P XX' —XX" ) —I I 0 ABBR DESCRIPTION GAS COCK GLOBE VALVE GV GATE VALVE IE INVERT PIPE ELEVATION PITCH LEFT PITCH RIGHT PLUG POC POINT OF CONNECTION PG PRESSURE GAUGE PRV PRESSURE REDUCING VALVE ROLLING 45 DOWN REDUCER REDUCING CONCENTRIC REDUCING ECCENTRIC RV RELIEF VALVE SHEET NOTE DESIGNATION SLEEVE SV SOLENOID VALVE TEE DOWN TEE TH THERMOMETER LONG TAG 9 CHARCTERS MAX MEDIUM TAG 6 CHARCTERS MAX SHORT TAG 4 CHARCTERS MAX TOP TOP OF PIPE ELEVATION U UNION UP VERTICAL SLEEVE VALVE IN PIPE RISE OR DROP STR WYE TYPE STRAINER ABBREVIATIONS AC AF AFF AHU AMB AMS B BDD BHP BI BOD BOT BTUH CC CFM CHLR CLG CNTFGL COMB COND CONT CONTR CP CRAC CT CU Cv CV CWP D DB DEG DIA DIM DISCH DMPR DN EA EAT ECONO EDH EER EF EFF ELEC ELEV EQUIV ESP EVAP EWT EXH EXT F FC FCU FD FLR FLTR FOIC FPM FSD FT FTU TV GA GAL GALV GPM GWB H HC HD HORIZ HP HT HVAC HVACDCS HX ID IN KW L LAT LB LWT MBH MECH MOD MTD MVD NC NIC NO NTS AIR CONDITIONING UNIT AIRFOIL ABOVE FINISHED FLOOR AIR HANDLING UNIT AMBIENT AIRFLOW MEASURING UNIT BOILER BACKDRAFT DAMPER BRAKE HORSEPOWER BACKWARD INCLINED BOTTOM OF DUCT BOTTOM BRITISH THERMAL UNIT PER HOUR COOLING COIL CUBIC FEET PER MINUTE CHILLER CEILING CENTRIFUGAL COMBUSTION CONDENSER / CONDENSATE CONTINUE / CONTROL CONTRACTOR CIRCULATING PUMP COMPUTER ROOM AIR CONDITIONING UNIT COOLING TOWER CONDENSING UNIT / CUBIC FLOW COEFFICIENT CONSTANT VOLUME CHILLED WATER PUMP DRAIN DRY BULB / DECIBEL DEGREE DIAMETER DIMENSION DISCHARGE DAMPER DOWN EXHAUST AIR ENTERING AIR TEMPERATURE ECONOMIZER ELECTRIC DUCT HEATER ENERGY EFFICIENCY RATIO EXHAUST FAN EFFICIENCY ELECTRIC ELEVATION EQUIVALENT EXTERNAL STATIC PRESSURE EVAPORATOR / EVAPORATIVE ENTERING WATER TEMPERATURE EXHAUST EXTERIOR / EXTERNAL FAHRENHEIT FORWARD CURVE FAN COIL UNIT FIRE DAMPER / FLOOR DRAIN FLOOR FILTER FURNISHED BY OWNER INSTALLED BY CONTRACTOR FEET PER MINUTE FIRE SMOKE DAMPER FEET FAN TERMINAL UNIT FACE VELOCITY GAUGE GALLONS GALVANIZED GALLONS PER MINUTE GYPSUM WALLBOARD HUMIDIFIER HEATING COIL HEAD HORIZONTAL HORSEPOWER HEAT TRACE HEATING, VENTILATING, AND AIR CONDITIONING HVAC DUCT CONSTRUCTION STANDARDS, METAL AND FLEXIBLE (SMACNA) HEAT EXCHANGER INDIRECT DRAIN / INSIDE DIAMETER INCH KILOWATT LONG / LENGTH LEAVING AIR TEMPERATURE POUND LEAVING WATER TEMPERATURE THOUSAND BTU PER HOUR MECHANICAL MOTOR OPERATED DAMPER MOUNTED MANUAL VOLUME DAMPER NORMALLY CLOSED / NOISE CRITERIA NOT IN CONTRACT NORMALLY OPEN / NUMBER NOT TO SCALE ABBREVIATIONS OBD OC OD OSA P PBD PD PL POC PT OPPOSED BLADE DAMPER ON CENTER OUTSIDE DIMENSION OR DIAMETER OUTSIDE AIR PUMP PARALLEL BLADE DAMPER PRESSURE DROP / PUMPED DRAIN PLENUM POINT OF CONNECTION POST- TENSION SLAB QD QUICK DISCONNECT RA REF REV RF RH RIO RPM SA SCFM SCH SECT SENS SF SL SMACNA SP SQ SS ST TBV TCV TDH TOD TOS TP TRNSN TSP TYP UBD UH UNO VA VAV VD VENT VEL VFO VI VIV WB WG WT RETURN AIR REFERENCE REVISION RELIEF FAN RELATIVE HUMIDITY ROUGH -IN ONLY REVOLUTIONS PER MINUTE SUPPLY AIR STANDARD CUBIC FEET PER MINUTE SCHEDULE SECTION SENSIBLE SUPPLY FAN / SQUARE FOOT SOUND LINE (INSIDE DUCT INSULATION ) SHEET METAL AND AIR CONDITIONING CONTRACTORS NATIONAL ASSOCIATION STATIC PRESSURE SQUARE STAINLESS STEEL SOUND TRAP TOWER BYPASS VALVE TEMPERATURE CONTROL VALVE TOTAL DYNAMIC HEAD TOP OF DUCT TOP OF STEEL TOTAL PRESSURE TRANSITION TOTAL STATIC PRESSURE TYPICAL UPBLAST DISCHARGE UNIT HEATER UNLESS NOTED OTHERWISE VALVE VARIABLE AIR VOLUME VOLUME DAMPER VENTILATION / VENTILATOR VELOCITY VARIABLE FREQUENCY CONTROLLER VIBRATION ISOLATOR VARIABLE INLET VANES INSULATED DUCT / WATT / WIDE WET BULB (TEMPERATURE) WATER GAUGE WEIGHT GENERAL NOTES 1. DRAWINGS ARE SCHEMATIC IN NATURE AND DO NOT SHOW EXACT ROUTING OR ALL TRANSITIONS /CONNECTIONS /OFFSETS REQUIRED. 2. COORDINATE ALL NEW WORK WITH EXISTING STRUCTURE AND HVAC. FIELD VERIFY EXISTING CONDITIONS. 3. ROUND CONNECTIONS TO RECTANGULAR DUCTWORK SHALL BE MADE WITH 45 DEG SADDLE TYPE TEES. 4. MAXIMUM FLEXIBLE DUCT LENGTH SHALL BE 6' -0" WITH A MAXIMUM BEND OF 90', FLEX DUCT SIZE SAME AS DIFFUSER NECK SIZE. 90' BENDS SHALL BE 2 TIMES THE DIAMETER OF THE ROUND DUCT. 5. PROVIDE REMOTE TYPE VOLUME DAMPERS FOR ALL AREAS WITH INACCESSIBLE CEILINGS. YOUNG REGULATOR No. 315 OR EQUAL. ALIGN DAMPER COVER PLATES. 6. LOCATE THERMOSTATS AS SHOWN ON DRAWINGS. MOUNT WALL THERMOSTATS AT 60" A.F.F. COORDINATE FINAL LOCATIONS WITH ARCH /ENGR /OWNER. 7. LOCATE THERMOSTATS FOR ALL TENATE IMPROVEMENT TERMINAL UNITS AT THE TERMINAL BOX WITH 20 FEET OF THERMOSTAT CONTROL WIRE ATTACHED TO THE THERMOSTAT. 8. PROVIDE CONNECTIONS AND TRANSITIONS AT EQUIPMENT AS REQUIRED. 9. INSTALLATION SHALL COMPLY TO ALL FEDERAL, STATE AND LOCAL CODES. 10. INSULATION OF DUCT WORK AND PIPING SHALL CONFORM TO THE WASHINGTON STATE ENERGY CODE AND THE SEATTLE AMENDMENTS 11. DUCTS PENETRATING 1 -HR CORRIDOR WALLS WITHOUT OPENING INTO THE CORRIDOR SHALL BE A MINIMUM 26 GAUGE STEEL. 12. ALL DUCT DIMENSIONS ARE ID (INTERNAL DIMENSIONS). ALL DUCT HEIGHTS ABOVE THE FINISHED FLOOR ARE TAKEN FROM THE DUCT'S ID DIMENSIONS. CONTRACTOR IS REQUIRED TO ADD TO THE DUCT ID WHEN THE DUCTWORK HAS INTERIOR INSULATION. ALL MECHANICAL ELEVATION ARE TO BOTTOM OF DUCT, BOTTOM OF PIPE. 13. MANUAL VOLUME DAMPERS TO 12" IN DEPTH SHALL BE SINGLE BLADE AND A MINIMUM OF 22 GAUGE. 13" AND ABOVE SHALL BE MULTIPLE BLADES AND A MINIMUM OF 18 GAUGE. 14. MANUAL VOLUME DAMPERS ARE REQUIRED AT EACH BRANCH DUCT GOING TO A SUPPLY AIR, RETURN AIR, AND EXHAUST AIR OUTLET OR INLET. 15. ACCESS DOORS SHALL BE REQUIRED AT EACH FIRE DAMPER, FIRE /SMOKE DAMPER, AND WHERE ACCESS TO ANY DEVICE IS REQUIRED FOR OPERATION OF THAT DEVICE. 16. USE UNISTRUT CONCRETE INSERTS, OR EQUAL, TO SUPPORT MECHANICAL EQUIPMENT OR DUCTWORK FROM THE P.T. SLAB. MpLO4?E? E VIEWED FOR E COMPLIANCE APPROVED MAY 11.2012 C_ ity of Tukwila LDING DIVISION R CEIVEU CITY OF TUKWIL A APR 1, 2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SYM REVISION A PERMIT PLANS BY UMC APPROVED DATE 04/13/12 SYM REVISION BY APPROVED DATE M"EirNG° ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED ENGINEER APPROVED BY DEPT. DATE MSH DRAWN UMC CHECKED DATE SUBTITLE 03 -14 -12 SYMBOLS, GENERAL NOTES, & ABBREVIATIONS CURRENT REVISION SYMBOL DATE A 03 -14 -2012 CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9 -101 BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES SHEET G1 JOB NO. COMP NO. TUKWILA, WA DWG NO. 9- 101 —G1 1:48 PM f: \acad \engineering \5761 \sheets \g2.dwg STEVE BUELER HEATING AND COOLING LOAD RECAP PROJECT NAME WEARER DATA LOCATION OUTDOOR SUMMER DB: OUTDOOR SUMMER WB: OUTDOOR WINTER DB: COOLIIG LOAD BREAKDOWN Boeing Building 9 -101 SEATTLE, WASHINGTON 82'F 66•F 24'F LOADUNK VERSION 2009A Elite Version 7.01.106 DATE 4/6/2012 ME 11:03:47 AM SAFETY FACTORS SENSIBLE LATENT 105 HEATING 120 AIR SYSTEM 11 DESCRIPTION AREA ROOF WALL WINDOW SKYLIGHT LIGHTS EQUIPMENT PEOPLE OUTSIDE AIR MISC. BLOCK COOLING TOTALS AREA SENS. GAIN LOAD % AREA SENS. GAIN LOAD % AREA SENS. GAIN LOAD % AREA SENS. GAIN LOAD % BTUH W /SF LOAD % BTUH W /SF LOAD % QUANTITY SF /PERSON TOTAL BTUH LOAD % CFM SENS. GAIN LATENT LOAD % BTUH LOAD % BTUH BTUH /SF SF/TON 1 VAV UNIT - CEILING SUPPLY 4,075 2,040 790 0.3% 3,999 , 6,651 2.8% 711 26,654 11.2% SKIN LOADS 754 7 15,295 1.10 6.4% 121,975 8.77 51.4% 102 40 50,006 21.1% 754 6,299 3,074 3.9% 6,641 2.8% 237,384 58 206 121,975 51.38% PEOPLE 102 285 10.00 21,956 28,050 50,006 21.07% VENTILATION CFM 754 44,334 47.26% 3,074 6,299 9,373 3.95% INFILTRATION CFM NO NO LEVEL 1 OPEN OFFICE LEV 1 -VAV UNIT - CEILING SUPPLY DRAW FAN 3 * -- 70 6,641 6,641 2.80% COOLJNG BLOCK LOAD AIR SYSTEM # DESCRIPTION INDOOR SETPOINT BLOCK CFM PEAK CFM CFM DN. SENS. GAIN TOTAL BTUH SENS. RATIO TONS CFM /SF SF/TON CFM/TON COIL DATA LVG. COIL D8, LVG. COIL WB LVG. COIL RR? COIL ENTHAUENT. COIL DB ENT. COIL WINTERING COIETRH COIL 1 VAV UNIT - CEILING SUPPLY 75'F 9,562 9,562 1.00 212,354 237,384 0.89 19.8 2.35 206 483 55.0 54.1 94.8 22.8 75.6 62.8 49.3 28.5 3,603 3.8% 3,999 27,814 29.7% 711 18,054 19.2% -- 530 10.00 0 15 SKIN LOADS 754 7 36,945 39.4% 34,095 34,095 14.36% LOAD BREAKDOWN PY AIR SYSTEM 11 DESCRIPTION AREA ROOF WALL WINDOW SKYLIGHT PARTITION OUTSIDE AIR INFILTRATION SLAB MISC. AREA SENS. LOSS LOAD % AREA SENS. LOSS LOAD % AREA SENS. LOSS LOAD % AREA SENS. LOSS , LOAD % AREA SENS. LOSS LOAD % CFM CFM /PERSON SENS. LOSS LOAD % CFM SENS. LOSS LOAD % AREA SENS. LOSS. LOAD % , BTUH LOAD % 1 VAV UNIT - CEILING SUPPLY 4,075 , 2,040 3,603 3.8% 3,999 27,814 29.7% 711 18,054 19.2% -- 530 10.00 0 15 SKIN LOADS 754 7 36,945 39.4% 34,095 34,095 14.36% UGHTING 4,075 NO 7,389 7.9% 15,295 15,295 6.44% EQUIPMENT 32,499 75 3 * 121,975 121,975 51.38% PEOPLE 102 285 10.00 21,956 28,050 50,006 21.07% VENTILATION CFM 754 44,334 47.26% 3,074 6,299 9,373 3.95% INFILTRATION CFM NO HEA11NO LOAD BLOCK LOAD AIR SYSTEM if DESCRIPTION INDOOR SETPOINT HEATING TOTALS OUTSIDE AIR COIL DATA HTG CFM TOTAL BTUH BTUH /SF CFM % OA TO HTG %FGA TO CLG C VG. COIL DB+TERING. COIL 1 VAV UNIT - CEILING SUPPLY 70'F 2,582 93,805 23 754 29% 8% 85.0 56.6 711 18,054 19.25% HVAC REDUNDANCY REQ'D 26,654 26,654 11.23% SKYLIGHT DB +/- DB RH % PROJECT TOTALS PROJECT LOAD AREA SEN. LOSS %TOT LATENT SENS. TOTAL %TOT ROOF 2,040 3,603 3.84% WINTER DESIGN TEMP 790 790 0.33% WALL 3,999 27,814 29.65% OPAQUE DOORS 6,651 6,651 2.80% GLASS 711 18,054 19.25% HVAC REDUNDANCY REQ'D 26,654 26,654 11.23% SKYLIGHT DB +/- DB RH % RH +/- % DB +/- DB RH % PARTITION LEVEL 1 LARGE CONFERENCE ROOM LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 * -- FLOOR SLAB 3 * -- 530 10.00 0 15 SKIN LOADS 6,750 49,471 52.74% 1.0 34,095 34,095 14.36% UGHTING 4,075 NO NO 15,295 15,295 6.44% EQUIPMENT 32,499 75 3 * 121,975 121,975 51.38% PEOPLE 102 285 10.00 21,956 28,050 50,006 21.07% VENTILATION CFM 754 44,334 47.26% 3,074 6,299 9,373 3.95% INFILTRATION CFM NO NO LEVEL 1 OPEN OFFICE LEV 1 -VAV UNIT - CEILING SUPPLY DRAW FAN 3 * -- 70 6,641 6,641 2.80% BLOW FAN 10.00 0 71 15 250 205 1.0 SUPPLY DUCT 1950 5 /P, 0.06 /FT2 139 NO RETURN DUCT NO LEVEL 1 COPY BREAK ROOM LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 RESERVE -- 70 3 * -- 150 10.00 PROJECT TOTALS 4,075 93,805 100.0% 25,030 212,354 237,384 100.00% 20 Tons BOEING BUILDING 9 -101 HVAC DESIGN CRITERIA 4/6/2012 PROJECT INFORMATION LOCATION SEATTLE, WASHINGTON LATTITUDE 47 ALTITUDE 400 WEATHER DATA DRY BULB WET BULB COMMENTS SUMMER DESIGN TEMP 82 66 AIRFLOW MEAN COINCIDENT DB /WB COMMENTS INDOOR INDOOR WINTER DESIGN TEMP 24 VOLUME (FT3) SQFT PER PERSON ENVELOPE U -VALUE S.C. COMMENTS ROOF INSULATION LIGHTS EQUIPMENT AIRFLOW WALL INSULATION COMMENTS INDOOR INDOOR FLOOR INSULATION CEILING HEIGHT (FT) VOLUME (FT3) SQFT PER PERSON SLAB INSULATION SENS. PER PERSON LAT. PER PERSON WATTS PER SQFT OPAQUE DOORS WATTS OSA METHOD MIN. SUPPLY (CFM) GLAZING MIN. OSA (ACHR) EXHAUST YES /NO AIR RECIRC IN ROOM HEATING CFM /SF 0.6 GLAZING SUMMARY SYS # % OF WALL % WALL & PART. % OF AREA 1 15% 17% Total 15% 15% 15% INTERNAL LOADS SUMMER WINTER ROOM METRICS PEOPLE LIGHTS EQUIPMENT AIRFLOW MISC. COMMENTS INDOOR INDOOR AREA (SQFT.) CEILING HEIGHT (FT) VOLUME (FT3) SQFT PER PERSON QUANTITY SENS. PER PERSON LAT. PER PERSON WATTS PER SQFT WATTS PER SQFT WATTS OSA METHOD MIN. SUPPLY (CFM) ROOM RELATIVE PRESS. MIN. OSA (ACHR) EXHAUST YES /NO AIR RECIRC IN ROOM HVAC REDUNDANCY REQ'D HVAC EMERGENCY POWER ROOM NAME FLOOR SYSTEM TYPE DB +/- DB RH % RH +/- % DB +/- DB RH % RH +/- % LEVEL 1 LARGE CONFERENCE ROOM LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 * -- 70 3 * -- 530 10.00 0 15 36 250 205 1.0 1.0 265 5 /P, 0.06 /FT2 212 NO NO NO LEVEL 1 SMALL CONFERENCE ROOM LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 * -- 70 3 * -- 285 10.00 0 14 20 250 205 1.0 143 5 /P, 0.06 /FT2 117 NO NO NO LEVEL 1 OPEN OFFICE LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 * -- 70 3 * -- 1,070 10.00 0 71 15 250 205 1.0 1950 5 /P, 0.06 /FT2 139 NO NO NO LEVEL 1 COPY BREAK ROOM LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 * -- 70 3 * -- 150 10.00 0 150 1 250 205 1.0 500 5 /P, 0.06 /FT2 14 NO NO NO LEVEL 2 OPEN OFFICE LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 * -- 70 3 * -- 950 10.00 0 73 13 250 205 1.0 1950 5 /P, 0.06 /FT2 122 NO NO NO LEVEL 2 STATIC CONTROL ROOM LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 * -- 70 3 * -- 410 10.00 0 59 7 250 205 1.0 15120 5 /P, 0.06 /FT2 60 NO NO NO LEVEL 2 FATIGUE CONTROL ROOM LEV 1 -VAV UNIT - CEILING SUPPLY 75 3 * -- 70 3 • * -- 680 10.00 0 68 10 250 205 1.0 _ 12570 _ 5 /P, 0.06 /FT2 91 NO NO NO TOTALS SYM REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE A PERMIT PLANS UMC 04/13/12 Q�BOE /NG° ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED DATE 03 -14 -12 2009 WSEC C01UFUANCE 1. HVAC EQUIPMENT SHALL HAVE MINIMUM PERFORMANCE AT SPECIFIED RATING CONDITIONS NOT LESS THAN THE VALUES INDICATED IN TABLE 14 -1A THROUGH 14 -1G AND 1411.1 OF THE WSEC AND AS INDICATED IN THE CONTRACT DOCUMENTS. 2. PROVIDE DEADBAND BETWEEN HEATING /COOLING SPACE SENSOR SETPOINTS OF 5 DEGREES AS REQUIRED BY SECTION 1412.2 OF THE WSEC OR AS DESCRIBED IN THE TEMPERATURE CONTROL SEQUENCES. 3. HVAC SYSTEMS SHALL BE EQUIPPED WITH AUTOMATIC CONTROLS CAPABLE OF ACCOMPLISHING SETBACK OR SHUTDOWN DURING UNOCCUPIED PERIODS AS REQUIRED BY SECTION 1412.4 OF THE WSEC AND AS DESCRIBED IN THE TEMPERATURE CONTROL SEQUENCES. 4. PROVIDE BALANCING DEVICES IN ALL BRANCH DUCTS AND PIPE RUNS TO TERMINAL DEVICES AS REQUIRED BY SECTION 1412.7 OF THE WSEC AND AS INDICATED ON THE CONTRACT DOCUMENTS. 5. ALL DUCTWORK SHALL COMPLY WITH SMACNA STANDARDS FOR CONSTRUCTION OF GALVANIZED DUCTWORK. ALL DUCTWORK SHALL BE SEALED AND TESTED AS REQUIRED BY SECTION 1414.1.1, 1414.1.2, AND 1414.1.3 OF THE WSEC. DUCT TAPE IS NOT PERMITTED AS A SEALANT ON ANY DUCTS. DUCTWORK STATIC PRESSURE AND SEAL CLASS: WATER COLUMN 1/2 TO 3 INCHES ABOVE 3 INCHES SEAL CLASS SEAL TRANSVERSE JOINTS AND LONGITUDINAL SEAMS SEAL TRANSVERSE JOINTS, LONGITUDINAL SEAMS, AND DUCT WALL PENETRATIONS 6. ALL DUCTWORK SHALL BE INSULATED AS REQUIRED BY SECTION 1414.2 OF THE SEC AND AS DESCRIBED IN THE PROJECT MANUAL. DUCT TYPE LOCATION R -VALUE SUPPLY /RETURN NOT WITHIN CONDITIONED SPACE 1.5 " - <4" SUPPLY /RETURN/ OUTSIDE AIR IN GROUND OR CONCRETE R -5.3 OUTSIDE AIR WITHIN CONDITIONED SPACE (NOT CONSIDERED PART OF THE BUILDING ENVELOPE) R -7 (DAMPER AT SUPPLY WITHIN CONDITIONED SPACE R -3.3 7. ALL PIPING SHALL BE INSULATED AS REQUIRED BY SECTION 1415.1 OF THE SEC AND AS DESCRIBED IN THE PROJECT MANUAL. SYSTEM/TEMP ('F) INSULATION CONDUCTIVITY PIPE DIAMETER <1" 1 " -<1.5" 1.5 " - <4" 4 " -<8" INSULATION THICKNESS HEATING: >350 .32 -.34 3.0 3.5 3.5 4.5 251 -350 .29 -.32 2.0 3.0 3.5 3.5 201 -250 .27 -.30 2.0 2.0 2.5 2.5 141 -200 .25 -.29 1.5 1.5 1.5 2.0 105 -140 .22 -.28 1.0 1.0 1.5 1.5 DOMESTIC: 105+ .22 -.28 1.0 1.0 1.5 1.5 COOLING: 40 -60 .22 -.28 1.0 1.00 1.5 1.5 =40 .22 -.28 1.0 1.5 1.5 1.5 8. INDIVIDUAL ZONE TERMINAL UNITS AND HVAC SYSTEMS SERVING PORTIONS OF THE BUILDING HAVING LESS THAN 24 -HOUR OPERATION SHALL BE SHUT OFF DURING UNOCCUPIED PERIODS AS REQUIRED BY SECTION 1432.1 OF THE WSEC AND AS DESCRIBED IN THE TEMPERATURE CONTROL SEQUENCES. 9. SUPPLY AIR AND WATER TEMPERATURES SHALL BE AUTOMATICALLY RESET AS REQUIRED IN SECTION 1432.2.1 AND 1432.2.2 OF THE WSEC OR AS DESCRIBED IN THE TEMPERATURE CONTROL SEQUENCES. 10. ALL AIR SYSTEMS SHALL BE PROVIDED WITH A 100% CAPABLE AIR ECONOMIZER AS REQUIRED BY THE SECTION 1413, 1423 AND 1433 OF THE WSEC AND AS DESCRIBED IN THE TEMPERATURE CONTROL SEQUENCES. 11. AIR AND WATER ECONOMIZERS SHALL BE CAPABLE OF PROVIDING PARTIAL COOLING EVEN WHEN ADDITIONAL MECHANICAL COOLING IS REQUIRED TO MEET THE REMAINDER OF THE COOLING LOAD AS REQUIRED IN SECTION 1413.3 OF THE WSEC. 12. WATER ECONOMIZERS SHALL BE CAPABLE OF PROVIDING THE TOTAL CONCURRENT COOLING LOAD SERVED BY THE CONNECTED TERMINAL EQUIPMENT LACKING AIRSIDE ECONOMIZER AS REQUIRED BY SECTION 1413.1, 1413.2, AND 1433 OF THE WSEC. 13. SIMULTANEOUS HEATING AND COOLING TO INDIVIDUAL ZONES SHALL BE PROHIBITED AS DESCRIBED IN THE TEMPERATURE CONTROL SEQUENCES EXCEPT WHERE PERMITTED IN SECTION 1435, EXCEPTIONS 1 THROUGH 6 OF THE WSEC. 14. VARIABLE FREQUENCY DRIVES SHALL BE PROVIDED FOR VARIABLE FLOW HEATING AND AIR HANDLING SYSTEMS AS REQUIRED BY SECTION 1438 OF THE WSEC AND AS DESCRIBED IN THE CONTRACT DOCUMENTS INCLUDING TEMPERATURE CONTROL SEQUENCES. 15. ELECTRIC WATER HEATERS LOCATED IN UNCONDITIONED SPACES OR ON CONCRETE FLOORS SHALL BE SEPARATED FROM THE SUPPORTING SURFACE WITH R -10 INSULATION AS DESCRIBED IN SECTION 1441 OF THE WSEC. 16. DOMESTIC HOT WATER CIRCULATION PUMPS SHALL BE SHUT DOWN DURING UNOCCUPIED PERIODS AS REQUIRED BY SECTION1442 OF THE WSEC AND AS DESCRIBED IN THE TEMPERATURE CONTROL SEQUENCES. 17. MOTOR EFFICIENCY SHALL NOT BE LESS THAN THE MINIMUM CALLOUTS PER TABLE 14 -4 AND SECTION 1437 OF THE WSEC FOR FULL LOAD EFFICIENCIES. 18. RECORD DRAWINGS SHALL BE PROVIDED TO THE OWNER AS REQUIRED BY SECTION 1416.3.4.2 OF THE SEC. THE DRAWINGS SHALL INDICATE THE LOCATION AND PERFORMANCE DATA OF EQUIPMENT, GENERAL CONFIGURATION OF DUCTWORK AND PIPING DISTRIBUTION SYSTEMS. 19. OPERATION AND MAINTENANCE MANUALS SHALL BE PROVIDED TO THE OWNER AS REQUIRED BY SECTION 1416.3.4.1 OF THE WSEC. AS A MINIMUM, THE MANUALS SHALL INCLUDE: 1. SUBMITTAL DATA. 2. OPERATION AND MAINTENANCE DATA FOR EQUIPMENT. 3. NAMES AND ADDRESSES OF • SERVICE AGENCIES. 4. HVAC CONTROLS SYSTEM MAINTENANCE AND CALIBRATION INFORMATION. 5. NARRATIVE OF HOW SYSTEM IS INTENDED TO. OPERATE. 20. HVAC SYSTEMS SHALL BE BALANCED AS REQUIRED BY, SECTION 1416.3.2 OF THE WSEC. 21. COMMISSIONING SHALL BE PROVIDED AND A REPORT OF COMMISSIONING BE SUBMITTED TO THE OWNER, AS REQUIRED BY SECTION 1416 OF THE WSEC. 111.1*--0 &le REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11 2012 City/ of Tukwila , BUILDING DIVISION R GENET; . CITY OF TUKWHA APR 19 2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SUBTITLE LOAD SUMMARY CURRENT REVISION SYMBOL A DATE 03 -14 -2012 APPROVED BY. DEPT. DATE ENGINEER MSH CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9- 101BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET G2 JOB NO. COMP NO. DWG NO. 9- 101 -G2 f: \acad \engineering \5761 \sheets \g3.dwg N s N STEVE BUELER PACKAGED ROOFTOP AIR - CONDITIONING UNIT SCHEDULE TAG ACU -1 TU -102 SERVICE IDS TOWER TU -202 LOCATION ROOF INTERSTITIAL INTERSTITIAL INTERSTITIAL INTERSTITIAL EQUIPMENT INTERSTITIAL AREA SERVED MANUFACTURER VAUNT OPEN OFFICE MODEL VPRX- 310 -25E OPEN OFFICE EFFICIENCY SEER /EER 12.2 NAILOR NAILOR NAILOR NAILOR SUPPLY FAN PERFORMANCE MODEL NO. 35SE CFM 9,595 35SE ESP 1.5 UNIT SIZE RPM 3 5 HP 5 5 QUANTITY 2 10 MIN OSA 800 10 % ECONOMIZER 100% 10.25x10.5 10.25x10.5 14.25x11.25 10.25x10.5 EXHAUST FAN PERFORMANCE 14.25x11.75 PLENUM SIZE CFM 9,000 SEE PLANS ESP 1 SEE PLANS RPM DDC DDC HP 3 DDC QUANTIFY 2 PRIMARY AIR MAX (CFM) 550 850 1,145 COOLING PERFORMANCE 630 1,000 TOTAL MBH 300.8 220 SENS MBH 255.7 205 EDB (DEG F) 75 1.0 EWB (DEG F) 63 1.0 OSA (DEG F) 95 FAN PERFORMANCE - ECM MOTOR FAN AIRFLOW (CFM) 550 850 FILTRATION 720 630 TYPE DISCH SP (IN WG) 0.50 % EFFICIENCY MERV 13 0.50 0.50 0.50 HYDRONC HEATING COL ELECTRICAL 2 2 RIA 2 2 MCA 79 64.4 MOP 90 65.7 VOLT 460 HEATER SIZE (KW) PHASE 3 8.0 5.0 4.0 7.0 PHYSICAL 87.3 88.3 WEIGHT 2,900 85.1 87.1 ELECTRICAL AFORMAT)ON VOLT /PHASE ACCESSORIES 460/3 460/3 SINGLE PT POWER CONN. YES 460/3 MICROPROC. CONTROLS 1/2 1/2 DB ECON W/ POWERED RELIEF 1/2 1/2 HIGH EFF. MOTORS YES / YES RADIATED NC 0 1" VFD (SUPPLY / EXHAUST) YES / YES 31 DBLE WALL W/ PERF. LINE 25 -- MOD GAS CONTROL VALVE 18 23 GRATES AT SUPPLY & RET. 19 19 EXTENDED LUBE UNES NOTES HOT GAS BYPASS MAGN PRES GA 0 FILTER BK NOTES: 1. ELECTRICAL TO POWER CONVENIENCE OUTLET(S) WITHIN 25FT. OF EACH UNIT. 2. FURNISH WITH VARIABLE SPEED DRNES; HIGH EFFICIENCY, INVERTER DUTY FAN MOTORS. 3. SMOKE DETECTOR REQUIRED, FURNISHED AND WIRED BY DMSION 16, INSTALLED IN DUCT BY DMSION 15 4. PROVIDE ECONOMIZER CONTROL FOR PARTIAL COOLING TO 100% OSA CAPABILITY. 5. E.C. (DIV 16) SHALL PROVIDE AND INSTALL FUSED DISCONNECT 6. PROVIDE SPRING ISOLATION CURB. BOEING BTE BUILDING -- SERIES VAV TERMINAL UNIT SCHEDULE TAG TU -101 TU -102 TU -103 1U -201 TU -202 TU -203 LOCATION INTERSTITIAL INTERSTITIAL INTERSTITIAL INTERSTITIAL INTERSTITIAL INTERSTITIAL AREA SERVED SMALL CONF LARGE CONF OPEN OFFICE STATIC CONTROL FATIGUE CONTROL OPEN OFFICE MANUFACTURER NAILOR NAILOR NAILOR NAILOR NAILOR NAILOR MODEL NO. 35SE 35SE 35SE 35SE 35SE 35SE UNIT SIZE 3 3 5 3 3 5 INLET SIZE (IN) 10 10 12 10 10 12 OUTLET SIZE (W x H) 10.25x10.5 10.25x10.5 14.25x11.25 10.25x10.5 10.25x10.5 14.25x11.75 PLENUM SIZE SEE PLANS SEE PLANS SEE PLANS SEE PLANS SEE PLANS SEE PLANS CONTROL DDC DDC DDC DDC DDC DDC AIR VALVE PERFORMANCE PRIMARY AIR MAX (CFM) 550 850 1,145 720 630 1,000 PRIMARY AIR MIN (CFM) 205 220 400 205 205 325 MAX INLET SP (IN WG) 1.0 1.0 1.0 1.0 1.0 1.0 FAN PERFORMANCE - ECM MOTOR FAN AIRFLOW (CFM) 550 850 1,125 720 630 1,000 DISCH SP (IN WG) 0.50 0.50 0.50 0.50 0.50 0.50 HYDRONC HEATING COL HEATER STAGES 2 2 2 2 2 2 COIL EAT (DEG -F) 64.4 66.1 64.8 65.7 65.1 65.1 HEATER SIZE (KW) 4.0 6.0 8.0 5.0 4.0 7.0 COIL LAT (DEG -F) 87.3 88.3 86.7 87.6 85.1 87.1 ELECTRICAL AFORMAT)ON VOLT /PHASE 460/3 460/3 460/3 460/3 460/3 460/3 MOTOR HP 1/2 1/2 3/4 1/2 1/2 3/4 ACOUSTICAL DATA RADIATED NC 0 1" 24 30 31 25 25 -- DISCHARGE NC 0 1" 18 23 21 19 19 -- NOTES 1. PROVIDE ALL VAV BOXES WITH ECM MOTORS AND ACOUSTICAL PACKAGE FOR NOISE MITIGATION 2. PROVIDE MINIMUM 50 VA TRANSFORMER 3. FIELD INSTALLED DAMPER ACTUATOR AND CONTROL CARD 4. PROVIDE SINGLE POINT POWER CONNECTION 5. PROVIDE RA FILTER BOEING BTE BUILDING -- SINGLE DUCT TERMINAL UNIT SCHEDULE TAG CV -201 CV -202 LOCATION INTERSTITIAL INTERSTITIAL AREA SERVED STATIC CONTROL FATIGUE CONTROL MANUFACTURER NAILOR NAILOR MODEL NO. D3001 D3001 INLET SIZE (IN) 14 14 OUTLET SIZE (W x H) 24x12.5 24x12.5 CONTROL DDC DDC CAPACITY AIRFLOW MAX (CFM) 2,500 2,200 AIRFLOW MIN (CFM) 0 0 ACOUSTICAL DATA RADIATED NC ®1" 26 25 DISCHARGE NC 0 1" 25 23 ACCESSORE8 INSULATION TYPE (STND /FOIL- FACE /IAQ) STANDARD STANDARD CONTROL TRANSFORMER N/A N/A DISCHARGE SOUND ATTENUATOR N/A N/A CONTROL CARD FIELD /FACTORY INSTALLED FACTORY FACTORY VOLT /PHASE 120/1 MOD CORE NOTES: 1. FIELD INSTALLED DAMPER ACTUATOR AND DDC CONTROL CARD FOR PRESSURE INDEPENDENT OPERATION EXHAUST FAN SCHEDULE TAG EF -1 MANUFACTURER LOCATION BREAK ROOM OPTIONS AREA SERVED INTERSTITIAL MATERIAL MANUFACTURER COOK NECK SIZE MODEL NO. 90SQN -10D CEILING DIFFUSER FAN TYPE INUNE MOD CORE DRIVE: BELT /DIRECT DIRECT 24X24 COMMENTS OFF -WHITE NONE FAN PERFORMANCE A2 CEIUNG DIFFUSER AIRFLOW (CFM) 150 MOD CORE ESP (IN WG) .375 24X24 TSP (IN WG) OFF -WHITE NONE FRPM 1,241 CEIUNG DIFFUSER MAX FRPM N/A MOD CORE MOTOR BHP 87 W 24X24 MOTOR HP 1/6 NONE ELECTRICAL DATA A4 CEIUNG DIFFUSER VOLT /PHASE 120/1 MOD CORE POWER NORMAL 24X24 MIN. CIRC. AMPACITY (MCA) -- NONE FULL LOAD AMPS (FLA) -- MAX. OVERCURRENT (MOCP) -- STARTER SEE CONTROL METHOD FURNISHED /INSTALLED EC / EC DISCONNECT BY ELECT. SUPPLY GRILLE FURNISHED /INSTALLED EC / EC FLOOR GRILLE CONTROL METHOD SURFACE 10" DIA TYPE DDC FURNISHED /INSTALLED CONTROL CONTR. SUPPLY GRILIF INTERLOCK BY CONTROL CONTR. FLOOR GRILLE COMMENTS WIRE TO WALL SWITCH SEE PLANS x 6" PHYSICAL DATA OFF -WHITE LENGTH (IN.) 17 WIDTH (IN.) 14 HEIGHT (IN). 14 OPERATING WEIGHT (LBS.) 1 125 ACCOUSTICAL DATA r2i C1 RETURN GRILLE LwA 61 EGGCRATE dBA 49 24X12 SONES 5.1 NONE ACCESSORIES C2 RETURN GRILLE INLET GRILLE -- EGGCRATE SPEED CONTROLLER X 24X24 BACK DRAFT DAMPER X NONE INVERTER RATED MOTOR -- RETURN GRILLE VIBRATION ISOLATORS -- SINGLE DEF MOTOR GUARD -- SEE PLANS BELT GUARD -- NONE NOTES NOTES: 1. DISCONNECT AND STARTER BY ELECTRICAL CONTRACTOR GRILLE, REGISTER AND DIFFUSER SCHEDULE EQUIP. ID NO. SERVICE / LOCATION MANUFACTURER MODEL DESCRIPTION OPTIONS NOTES STYLE MATERIAL FRAME FACE SIZE NECK SIZE COLOR Al CEILING DIFFUSER TITUS MCD MOD CORE STEEL LAY -IN 24X24 6" DIA OFF -WHITE NONE A2 CEIUNG DIFFUSER TITUS MCD MOD CORE STEEL LAY -IN 24X24 8" DIA OFF -WHITE NONE A3 CEIUNG DIFFUSER TITUS MCD MOD CORE STEEL LAY -IN 24X24 10" DIA OFF -WHITE NONE A4 CEIUNG DIFFUSER TITUS MCD MOD CORE STEEL LAY -IN 24X24 12" DIA OFF -WHITE NONE B1 SUPPLY GRILLE TROX FB -200 FLOOR GRILLE ALUMINUM SURFACE 10" DIA SEE PLANS OFF -WHITE 1 82 SUPPLY GRILIF TITUS CT -540 FLOOR GRILLE STEEL SURFACE SEE PLANS x 6" - -- OFF -WHITE C1 RETURN GRILLE TITUS 50F EGGCRATE ALUMINUM LAY -IN 24X12 22X10 OFF -WHITE NONE C2 RETURN GRILLE TENS 50F EGGCRATE ALUMINUM LAY -IN 24X24 22X22 OFF -WHITE NONE C3 RETURN GRILLE TITUS 350 RL SINGLE DEF STEEL SURFACE SEE PLANS - -- OFF -WHITE NONE NOTES: 1. PROVIDE "TROX" 12x12 SUPPLY NR PLENUM WITH DIFFUSER 2. ACU -1 (SEQUENCE OF OPERATION) C OOLNG ONLY, UST WITH RETIWN / EXHAUST FAN SEQUENCE THIS IS A VARIABLE - VOLUME, COOLING -ONLY, WITH DX COOLING COIL, FACTORY CONTROLS, AND RETURN /EXHAUST FANS. A. OPERATION 1 THIS UNIT IS TO BE A VARIABLE VOLUME SYSTEM EQUIPPED WITH VARIABLE VOLUME SUPPLY FAN WITH VARIABLE FREQUENCY DRIVE, RETURN / EXHAUST FAN WITH VARIABLE FREQUENCY DRIVE, FILTERS, DX COOLING COIL, VENTILATION, ECONOMIZER AND RETURN AIR DAMPERS. 2 THE PACKAGED AIR HANDLING SYSTEM SHALL BE FURNISHED WITH A COMPLETE, FACTORY - INSTALLED, DDC CONTROL SYSTEM BASED ON AN OPEN PROTOCOL TO BE SELECTED BY THE ENGINEER. B. OCCIIPED CYCLE 1 FAN START /STOP: ON COMMAND FROM THE FACTORY CONTROLER, SYSTEM STARTUP SEQUENCE SHALL BE INmATED, THE RETURN DAMPER SHALL BE FULLY OPEN, VENTILATION, ECONOMIZER AND RELIEF DAMPERS CLOSED, THE SUPPLY AND RETURN FANS SHALL START, RAMPING UP TO SETPOINT AS PROGRAMMED BY THEIR VARIABLE SPEED DRIVE CONTROL.. START SHALL BE BASED ON OPTIMAL START CALCULATION BY THE FACTORY CONTROLLER. 2 SUPPLY FAN SPEED CONTROL: THE EMCS SHALL VARY THE SPEED OF THE SUPPLY FAN VFD TO MAINTAIN SUPPLY DUCT STATIC PRESSURE AS SENSED BY A DIFFERENTIAL SENSOR AS LOCATED 2/3 DOWN SUPPLY DUCTWORK THE DDC SYSTEM SHALL RESET DUCT STATIC PRESSURE IN A RANGE OF 0.5" TO 1.0" TO ASSURE THAT NO TERMINAL PRIMARY AIR DAMPER EXCEEDS A 95% OPEN POSmON. 3 RETURN / EXHAUST FAN SPEED CONTROL: THE DDC SYSTEM SHALL VARY THE SPEED OF THE VARIABLE FREQUENCY DRIVE TO MAINTAIN A SPACE STATIC PRESSURE OF (+ .05" WG) ABOVE FACTORY. 4 VENTILATION AIR DAMPER CONTROL: ON FAN START, VENTILATION AIR DAMPER SHALL OPEN TO ADMIT THE DESIGN VENTILATION AIRFLOW AS SCHEDULED ON THE AIR HANDLING UNIT SCHEDULE. OUTSIDE AIR DAMPER SHALL BE CLOSED DURING UNOCCUPIED HOURS. 5 MIXED AIR TEMPERATURE CONTROL: THE MINIMUM MIXED AIR SETPOINT SHALL BE 55 DEGREES F (ADJUSTABLE). 6 ECONOMIZER OPERATION: WHEN THE OUTDOOR AIR TEMPERTURE IS BELOW RETURN AIR TEMPERATURE, THE ECONOMIZER DAMPER SHALL MODULATE TO MAINTAIN THE DESIGN MIXED AIR TEMPERATURE SETPOINT. ON RISE IN OUTDOOR AIR TEMPERATURE ABOVE RETURN TEMPERATURE, THE ECONOMIZER DAMPER SHALL CLOSE. 7 DUCT SMOKE DETECTORS: THE DETECTORS, PROVIDED BY THE DMSION 16 CONTRACTOR, SHALL BE WIRED TO THE VARIABLE FREQUENCY DRIVE INPUTS TO STOP BOTH THE SUPPLY AND RETURN FANS WHEN TRIPPED. ON FAN STOP VENTILATION, ECONOMIZER, OUTDOOR AIR AND EXHAUST DAMPERS SHALL RETURN TO NORMAL POSmONS. 8 HIGH STATIC PRESSURE LIMIT: PROVIDE A SENSOR IN THE DISCHARGE PLENUM TO STOP SUPPLY AND RETURN FANS AND RETURN DAMPERS TO NORMAL POSITIONS WHEN THE SETPOINT OF 4.0" (ADJUSTABLE) IS EXCEEDED. 9 FIRE ALARM SIGNAL: ON RECEIPT OF A FIRE ALARM FROM THE DIVISION 16 CONTRACTOR'S SYSTEM, THE SUPPLY AND RETURN FANS SHALL STOP, DAMPERS SHALL RETURN TO NORMAL POSITIONS. 10 SUPPLY FAN VFD FAILURE: ON FAILURE OF THE SUPPLY FAN VARIABLE FREQUENCY DRIVE, THE UNIT SHALL AUTOMATICALLY SWITCH TO BYPASS MODE AND RUN AT FULL SPEED (60 HZ). 11 RETURN FAN VFD FAILURE: ON FAILURE OF THE RETURN FAN VARIABLE FREQUENCY DRIVE, THE FAILED FAN SHALL STOP. C. UNOCCUPIED MODE 1 IN THE UNOCCUPIED MODE, WHEN SCHEDULED BY THE DDC SYSTEM, BOTH THE SUPPLY AND RETURN FANS SHALL BE OFF AND DAMPERS IN NORMAL POSmONS. UNOCCUPIED SPACE HEATING SETPOINT SHALL BE MAINTAINED AT 65 DEGREES F (ADJUSTABLE) BY THE SYSTEM'S ASSOCIATED FAN TERMINAL UNITS AND THEIR HEATING COILS. 2 WARMUP /COOLDOWN: ON A SWITCH TO THE OCCUPIED CYCLE, AS DETERMINED BY THE EMCS, THE WARMUP CYCLE SHALL BE INITIATED. THE SUPPLY FANS SHALL BE STARTED AND DAMPERS SHALL BE POSMONED TO PROVIDE A 100% RECIRCULATION MODE AND THE OSA VENTILATION DAMPER SHALL BE CLOSED. HEATING COILS IN INDMDUAL FAN TERMINALS SHALL BE ENERGIZED UNTIL THE INDIVIDUAL SPACES REACH OCCUPIED SPACE TEMPERATURE SETPOINT OF 70 DEGREES F. ON A RISE IN THE AIR HANDLING UNIT RETURN AIR TEMPERATURE TO 70 DEGREES, THE UNIT SHALL AUTOMATICALLY SWITCH TO THE OCCUPIED MODE, ENABLING THE EXHAUST FAN SEQUENCE AND IMPLEMENTING DISCHARGE AIR TEMPERATURE CONTROL AS WELL AS OPENING THE VENTILATION DAMPER. WARM WEATHER COOLDOWN MODE: UNIT SHALL START IN NORMAL MODE, OPENING VENTILATION AND SEQUENCING ECONOMIZER DAMPERS AS REQUIRED TO REACH DESIGN SPACE TEMPERATURE. 3 UNOCCUPIED THERMOSTAT OVER -RIDE: UPON AN OCCUPANT PRESSING THE UNOCCUPIED OVER -RIDE SWITCH ON THE LOCAL THERMOSTAT, IN THE HEATING MODE THE LOCAL FAN TERMINAL SHALL CYCLE TO MAINTAIN THE OCCUPIED DAYTIME TEMPERATURE. IN A COOLING MODE, THE FAN TERMINAL SHALL RUN AND PRIMARY AIR VALVE SHALL MODULATE TO MAINTAIN SETPOINT. IF SPACE TEMPERATURE CANNOT BE MAINTAINED BY AIR CIRCULATION, AIR HANDLING UNIT SHALL START. SYM REVISION A PERMIT PLANS BY UMC APPROVED DATE 04/13/12 SYM REVISION BY APPROVED DATE B G' ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED TYPICAL OFFICE UNIT SEQUENCES - FAN TERMNAL AND SHUTOFF BOXES A. OPERATION - SEtES FLOW FAN TERMINAL INT WITH ELECTRIC HEAT 1 OCCUPED CYCLE - PROVIDE TERMINAL UNIT CONTROLLER FOR PRESSURE INDEPENDENT OPERATION. - - IN THE OCCUPIED MODE, FANS SHALL RUN CONTINUOUSLY AND THE EMCS SHALL MODULATE THE PRIMARY AIR DAMPER AND ELECTRIC HEATING COIL CONTACTS IN SEQUENCE TO MAINTAIN SETPOINT. SEE FAN TERMINAL UNIT SCHEDULE ON THE DRAWINGS FOR MINIMUM AND MAXIMUM AIRFLOW SETPOINTS. 2 UNOCCX PED CYCLE -- DURING UNOCCUPIED PERIODS, FANS SHALL STOP AND PRIMARY AIR DAMPERS IN INDIVIDUAL UNITS SHALL CLOSE. PROVIDE SCHEDULING CAPABILITY FOR INDIVIDUAL TERMINALS, OCCUPIED OR UNOCCUPIED THRU THE EMCS. -- ON A DROP IN SPACE TEMPERATURE BELOW THE UNOCCUPIED SETPOINT, THE TERMINAL FAN SHALL BE ENERGIZED AND THE HEATING COIL CONTACTS CLOSED UNTIL THE UNOCCUPIED SPACE TEMPERATURE IS RE- ESTABLISHED. AT THAT POINT THE FAN SHALL STOP AND THE HEATING COIL BE DE- ENERGIZED. 3 WARMUP - - ON MORNING WARMUP, THE TERMINAL FAN SHALL BE STARTED AND THE HEATING COIL ENABLED UNTIL THE SPACE OCCUPIED TEMPERATURE SETPOINT IS REACHED. THE PRIMARY AIR DAMPER SHALL REMAIN CLOSED. ALL TERMINALS FOR AN INDMDUAL AIR HANDLING UNIT SHALL REMAIN IN THE WARMUP MODE UNTIL THE AIR HANDLING UNIT HAS SWITCHED OVER TO THE OCCUPIED MODE AS DESCRIBED IN THE AIR HANDLING UNIT CONTROL SEQUENCE. 4 VENTLAT)ON OVERRIDE - - IN CONFERENCE ROOMS A SEPARATE CARBON DIOXIDE SENSOR ADJACENT TO THE SPACE TEMPERATURE SENSOR SHALL BE PROVIDED. WHEN INDOOR CO2 LEVELS EXCEED OUTDOOR LEVELS BY MORE THAN 500 PARTS PER MILLION (ADJUSTABLE), THE PRIMARY AIR DAMPER SHALL OPEN 20% FOR 10 MINUTES. IF HIGH CO2 CONDITION REMAINS, OPEN PRIMARY AIR DAMPER ANOTHER 20% FOR 10 MINUTES AND REPEAT AS NEEDED. IF SPACE TEMPERATURE IS NOT MAINTAINED WITH HEATING COIL ENABLED, THE PRIMARY AIR DAMPER SHALL RETURN TO PREVIOUS SETTING AND A WARNING SHALL BE GENERATED AT THE EMCS WORKSTATION. B. OPERATION - VARIABLE VOLUME SHUTOFF BOX WITH FEAT 1 =WED CYCLE - PROVIDE TERMINAL UNIT CONTROLLER FOR PRESSURE INDEPENDENT OPERATION. -- IN THE OCCUPIED MODE THE EMCS SHALL MODULATE THE PRIMARY AIR DAMPER TO MAINTAIN SETPOINT. SEE TERMINAL UNIT SCHEDULE ON THE DRAWINGS FOR MINIMUM AND MAXIMUM AIRFLOW SETPOINTS. 2 UNOCCWED CYCLE - - DURING UNOCCUPIED PERIODS PRIMARY AIR DAMPERS IN INDMDUAL UNITS SHALL CLOSE. PROVIDE SCHEDULING CAPABILITY FOR INDMDUAL TERMINALS, OCCUPIED OR UNOCCUPIED THRU THE EMCS. M I 0 bc2 DATE SUBTITLE 03 -14 -12 REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11 2012 "` City of Tukwila BUILDING DIVISION R CEIVEU TUKWL CITY OF A APR 1,2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. MECHANICAL SCHEDULES SEQUENCE OF OPERATIONS CURRENT REVISION SYMBOL DATE 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9 -101 BTE TEST FRAME SHEET G3 JOB NO. COMP NO. PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA DWG N0. 9- 101 -G3 1:48 PM f: \acad \engineering \5761 \sheets \g4.dwg N 0 J w m DUCT INSULATION SCHEDULE DUCT FUNCTION SUPPLY AIR <55 DEG SUPPLY AIR <55 DEG SUPPLY AIR <55 DEG SUPPLY AIR <55 DEG SUPPLY AIR <55 DEG RETURN AIR RETURN AIR RETURN AIR RETURN AIR RETURN AIR OUTDOOR AIR INTAKE GENERAL EXHAUST INT /EXH PLENUMS LOCATION INDOOR INDOOR INDOOR OUTDOOR OUTDOOR INDOOR INDOOR INDOOR OUTDOOR OUTDOOR INDOOR INDOOR INDOOR SHAPE RECT RECT ROUND RECT RECT RECT RECT ROUND RECT RECT RECT RECT RECT INSULATION TYPE WRAP LINED WRAP WRAP LINED WRAP LINED WRAP WRAP LINED WRAP WRAP BOARD THICKNESS 1.5" 1" 1.5" 3" 2" 1.5" 1" 1.5" 3" 2" 3" 3" 2" DENSITY 0.75 PCF 2.0 PCF 0.75 PCF 0.75 PCF 2.0 PCF 0.75 PCF 2.0 PCF 0.75 PCF 0.75 PCF 2.0 PCF 0.75 PCF 0.75 PCF 3.0 PCF R' VALUE 3.3 3.3 3.3 7.0 7.0 3.3 3.3 6.4 7.0 7.0 7.0 7.0 7.0 FACING (JACKET) FOIL FACED N/A FOIL FACED FOIL FACED N/A FOIL FACED N/A FOIL FACED FOIL FACED N/A FOIL FACED FOIL FACED FOIL FACED REMARKS 0.32 -0.34 250 FIBERGLASS 1.5 2.5 2.5 3.0 3.5 3.5 CHILLED WATER 40 -55 [1] 75 REMARKS: 1. INSTALL EXTERNAL WRAP FROM RELIEF AIR CONTROL DAMPER OR BACKDRAFT DAMPER TO PLENUM CONNECTION PIPE + EQUIPMENT INSULATION SCHEDULE COOLING COIL CONDENSATE (23 2213) ABOVE GROUND TEMP RANGE 2' + SMALLER f 91A8 CATION MATERIAL PIPE SUE RUNOUTS To 2(2) r AND LESS PIPE MATERIALS 21/r To 4 DWV Copper OVER e' JOINT TYPE ALL LEAD -FREE SOLDER 75 FITTING MATERIAL 0.5 ASME B16.29 WROUGHT DWV 0.5 0.5 0.5 0.5 NON- POTABLE COLD TEST /INSPECTION 0.23 -0.27 75 FIBERGLASS UMC WELD PROCEDURE 0.5 0.5 0.5 WELD INSPECTION (Visual, X -ray, etc ?) 0.5 DOMESTIC HOT > 105 INSPECTION 100 FIBERGLASS 0.5 - Media (Air, Water, Agron, Nitrogen, etc ?) 1.0 WATER 1.5 - Duration NON - POTABLE HOT 4 HOURS 0.24 -0.28 - Pressure (psi or ft. head) ?) 10 FEET OF HEAD OWNER REP / VERIFY WITH AUTHORITY 1.0 - Responsible (City, Owner, Owner Rep., etc 1.5 1.5 1.5 STORM DRAIN PIPE + EQUIPMENT INSULATION SCHEDULE PIPING SYSTEM TEMP RANGE 11AAL CONDUCTMTY MEAN RAITNQ TEEFERATURE CATION MATERIAL PIPE SUE RUNOUTS To 2(2) r AND LESS 11/4' To r 21/r To 4 V To V OVER e' DOMESTIC COLD ALL 0.23 -0.27 75 FIBERGLASS 0.5 0.5 0.5 0.5 0.5 0.5 NON- POTABLE COLD ALL 0.23 -0.27 75 FIBERGLASS 0.5 0.5 0.5 0.5 0.5 0.5 DOMESTIC HOT > 105 0.24 -0.28 100 FIBERGLASS 0.5 1.0 1.0 1.5 1.5 1.5 NON - POTABLE HOT >105 0.24 -0.28 100 FIBERGLASS 0.5 1.0 1.0 1.5 1.5 1.5 STORM DRAIN ALL 0.23 -0.27 75 FIBERGLASS 0.5 0.5 0.5 0.5 0.5 0.5 HEATING WATER 105 -140 0.24 -0.28 100 FIBERGLASS 0.5 1.0 1.0 1.0 1.5 1.5 HEATING WATER 141 -200 0.25 -0.29 125 FIBERGLASS 0.5 1.5 1.5 1.5 1.5 1.5 HEATING WATER 201 -250 0.27 -0.30 150 FIBERGLASS 1.0 1.5 1.5 2.0 2.0 3.5 HEATING WATER 251 -350 0.29 -0.31 200 FIBERGLASS 1.5 2.0 2.5 2.5 3.5 3.5 HEATING WATER >350 0.32 -0.34 250 FIBERGLASS 1.5 2.5 2.5 3.0 3.5 3.5 CHILLED WATER 40 -55 0.23 -0.27 75 FIBERGLASS 0.5 0.5 0.75 1.0 1.0 1.0 CONDENSER WATER (1) 40 -55 0.23 -0.27 75 FIBERGLASS 0.5 0.5 0.75 1.0 1.0 1.0 LOW PRESS STEAM 0 -30# 0.29 -0.31 200 FIBERGLASS 1.5 2.0 2.5 2.5 3.5 3.5 LOW PRESS COND <210 DEG 0.27 -0.30 200 FIBERGLASS 1.0 1.5 1.5 2.0 2.0 3.5 MED PRESS STEAM 30 -60# 0.29 -0.31 200 FIBERGLASS 1.5 2.0 2.5 2.5 3.5 3.5 MED PRESS COND 270 -300 DEG 0.29 -0.31 200 FIBERGLASS 1.5 2.0 2.5 2.5 3.5 3.5 HIGH PRESS STEAM 60 -125# 0.29 -0.31 200 FIBERGLASS 1.5 2.0 2.5 2.5 3.5 3.5 HIGH PRESS COND >300 DEG 0.29 -0.31 200 FIBERGLASS 1.5 2.0 2.5 2.5 3.5 3.5 REFRIG SUCTION ALL 0.27 -0.276 75 CLOSED CELL N/A 0.375 0.5 0.5 0.75 0.75 GENERATOR EXHAUST TO 1100 DEG 0.55 700 CAL -SIL N/A N/A N/A 3.0 3.0 3.0 COIL CONDENSATE ALL 0.23 -0.27 75 FIBERGLASS 0.5 0.5 0.5 0.5 0.5 0.5 INSULATED SUPPORTS NSUL ATION 11iC:KNESS TO 1/2' 3/4' T 1 1/2' 2' -3' OVER 3' THERMAL SUPPORTS ALL TRYMER 2000 CAL -SIL CAL -SIL CAL -SIL CAL -SIL CAL -SIL NOTES 1 HYDRONIC ECONOMIZER APPLICATIONS ONLY. 2 RUNOUTS TO INDIVIDUAL TERMINALS NOT EXCEEDING 12 FEET IN LENGTH MINIMUM MOTOR EFFICIENCY STANDARDS OPEN MOTORS CLOSED MOTORS SPEED 3600 1800 1200 3600 1800 1200 HP EFFICIENCY EFFICIENCY EFFICIENCY EFFICIENCY EFFICIENCY EFFICIENCY 1 77.0 85.5 82.5 77.0 85.5 82.5 1.5 84.0 86.5 86.5 84.0 86.5 87.5 2 85.5 86.5 87.5 85.5 86.5 88.5 3 85.5 89.5 88.5 86.5 89.5 89.5 5 86.5 89.5 89.5 88.5 89.5 89.5 7.5 88.5 91.0 90.2 89.5 91.7 91.0 10 89.5 91.7 91.7 90.2 91.7 91.0 15 90.2 93.0 91.7 91.0 92.4 91.7 20 91.0 93.0 92.4 91.0 93.0 91.7 25 91.7 93.6 93.0 91.7 93.6 93.0 30 91.7 94.1 93.6 91.7 93.6 93.0 40 92.4 94.1 94.1 92.4 94.1 94.1 50 93.0 94.5 94.1 93.0 94.5 94.1 60 93.6 95.0 94.5 93.6 95.0 94.5 75 93.6 95.0 94.5 93.6 95.4 95.4 100 93.6 95.4 95.0 94.1 95.4 95.0 125 94.1 95.4 95.0 95.0 95.4 95.0 150 94.1 95.8 95.4 95.0 95.8 95.8 200 95.0 95.8 95.4 95.4 96.2 95.8 250 95.0 95.8 95.4 95.8 96.2 95.8 300 95.4 95.8 95.4 95.8 96.2 95.8 350 95.4 95.8 95.4 95.8 96.2 95.8 400 95.8 95.8 95.8 95.8 96.2 95.8 450 95.8 96.2 96.2 95.8 96.2 95.8 500 95.8 96.2 96.2 95.8 96.2 95.8 NOTE: 1. SOURCE: WSEC 2009 EDMON M 0 ki0 REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11 2012 City of Tukwila BUILDING DIVISION RECktvku .. CITY OF TUKWILA APR 1 3,2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SYM A REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE PERMIT PLANS UMC 04/13/12 Q�BOE /iVG' ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED DATE 03 -14 -12 SUBTITLE MECHANICAL SCHEDULES CURRENT REVISION SYMBOL A DATE 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9- 101BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET G4 JOB NO. COMP NO. DWG NO. 9- 101 -G4 1:48 PM f:\acad\engineering\5761\sheetAm211.dwg 6 STEVE BUELER [] j J U.3 J - U- u- Lru-Ln 1 , -t j 80 UP TO EF -1 i1 2 A4 425 2 x x [J 2 I- A4 425 2 2 T -STAT WIRING UP TO TU -102 --I 2 2 190 (1YP 5) 2 X X 2 - 2 - T -STAT WIRING UP TO TU -103 ■ 2 - x 2 x HVAC PLAN - LEVEL 1 SCALE: 1/4' =1' -0' • 195 WALL SWITCH TO EF -1 IN X TO BE WIRED UERSTE!. T -STAT WIRING UP TO TU -101 z / X 260 X 260 2 - T2 = SYM REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE A PERMIT PLANS UMC 04/13/12 Q�BOE /NG' ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED 2 - DRAWN UMC CHECKED 2 DATE 03 -14 -12 2 2 2 2 2 - 2 - REVIEWED FOR CODE COMPLIANCE APPROVED MAY 112012 City of Tukwila BUILDING DIVISION 2 NORTH ARROW 2 2) CITY RE OCtivtu F TUKIMLA APR 1,32012 PERMIT CANTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SUBTITLE HVAC PLAN - LEVEL 1 CURRENT REVISION SYMBOL DATE 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9 -101 BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET M211 JOB NO. COMP NO. DWG NO. 9- 101 -M211 1:48 PM f: \acad\ engineering \5761 \sheets \m2li.dwg STEVE BUELER 0 (1 0 0 0 U.2 flu- u-lruzrLn 4 2 — 2 } 2 1 G.C. TO PROVIDE FLOOR PENETRATIONS FOR DUCT WORK SERVING 1ST FLOOR CEILING (TYP.) 2 — __ 2 16x12. T FL TT- T 2 (C( I 80 2 — I i 120 20x12 7-100 UP I (K9 2 TT-- 2 - 80 1 100 UP TO TU -201 2 — SA DN THRU FLOOR TO DIFFUSER IN 1ST FLOOR CEILING (iYP) PROVIDE MAXIMUM 6 FT OF STRAIGHT FLEX IN VERTICAL DN TO SUPPLY GRILLE AT 1ST FLOOR (TYP) 2 — iI 2 v S 0 0 • 0 10 SYM REVISION BY A PERMIT PLANS UMC APPROVED DATE 04/13/12 SYM REVISION BY APPROVED DATE or J 2 2 — "ID 2 — HVAC PLAN - LOWER LEVEL INTERSTITIAL SCALE: 1/4' =1' -0' QBOE /NG° a ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED ENGINEER APPROVED BY DEPT. DATE MSH CHECKED DRAWN UMC CHECKED 2 3 DATE SUBTITLE 03 -14 -12 2 2 — 2 —0 2 — 2 — 141 0.4) b HVAC PLAN LOWER LEVEL INTERSTITIAL 2 — 2 — 2 REVIEWED FOR CODE COMPLIANCE APPROVED MAY 112012 City of Tukwila BUILDING DIVISION NORTH ARROW CURRENT REVISION CITY O TIJKWLA APR 1.3 2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SYMBOL A DATE 03 -14 -2012 APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9 -101 BTE TEST FRAME SHEET M211 JOB NO. COMP NO. PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA DWG NO. 9- 101 —M211 1:48 PM f: \acad\ engineering \5761 \sheets \m22i.dwg 1J Tr SA PLENUM BOX ATTACHED TO FLOOR DIFFUSER (1YP) - GC TO PROVIDE PENETRATION IN LEVEL 2 SLAB FOR FLOOR MOUNTED SUPPLY GRILLES (TYP) 0 T l l U.2 iJ- u- 1r15-u-Ln Ciz) 0 0 /24x24 0 n 120 120 120 2 I HIM 80 0 16x10 80 (TYP) 1-1 FE n 2 1U -202 2 UP raniiniic 4- 100 80 0 20x12 0 160 100 C 0 TU -203 120 DN TO TU -103 24x24 XFER UP -� 140 DN ALL DUCTWORK SHALL BE BELOW FIRE PROTECTION PIPING WHICH IS AT 8'-6' AFF� , Y' 100 DN TO 111-201 [1 lit 0 0 — 2 — 1J ff�1 24x24 IIIIIn e 1J 34x24 SA UP 80 BREAK ROOM EXHAUST, TERMINATE AT EXTERIOR OF BUILDING AN PROVIDE SCREEN OVER OPENING 0 22x16 CV-20 0 r 0 I I II .' 0 iiiI:41I11 Id? 0 0 0 16x10 80 LI I • 11 100 DN 0 0 2 — 2 HVAC PLAN - UPPER LEVEL INTERSTITIAL SCALE: 1/4' =l' -0' 2 — 2 }— 2 2 — 2 —0 2 — 2 — 2 — 2 2 REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11 2012 1> City of Tukwila BUILDING DIVISION R Cklil�Ll.. CITY TUKIMLA APR 13 2012 PERMIT CENTER NORTH ARROW Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. a SYM N N A STEVE BUELER REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE PERMIT PLANS UMC 04/13/12 ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED DATE 03 -14 -12 SUBTITLE HVAC PLAN UPPER LEVEL INTERSTITIAL CURRENT REVISION SYMBOL DATE 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPR VED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9 -101 BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET M22i JOB NO. COMP NO. DWG NO. 9- 101 -M22i c- `J T HVAC PLAN - UPPER LEVEL INTERSTITIAL SCALE: 1/4' =l' -0' 2 — 2 }— 2 2 — 2 —0 2 — 2 — 2 — 2 2 REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11 2012 1> City of Tukwila BUILDING DIVISION R Cklil�Ll.. CITY TUKIMLA APR 13 2012 PERMIT CENTER NORTH ARROW Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. a SYM N N A STEVE BUELER REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE PERMIT PLANS UMC 04/13/12 ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED DATE 03 -14 -12 SUBTITLE HVAC PLAN UPPER LEVEL INTERSTITIAL CURRENT REVISION SYMBOL DATE 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPR VED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9 -101 BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET M22i JOB NO. COMP NO. DWG NO. 9- 101 -M22i 1:48 PM f: \acad\ engineering \5761 \sheets \m221.dwg STEVE BUELER Cv) 'c T -STAT WIRING TO CV -201 2 T (1q) 1 T x I J.1 tN.2 481Yx24 °Dx36 °H RA PLENUM 24x18 RA UP 24x24 RA UP & DN AREA IN FRONT OF RETURN NR GRILLES TO BE FREE OF OBSTRUCTIONS (TYP) 9 FT. (FSG -2) CENTERED 01t) COMPUTER RACKS 2 I- 0 2 - 2 T -STAT WIRING TO N- 202.r� 0 0 0 I 0 0 B1 90 (7 TYP) 9 0 111 20x16 RA UP ✓� 24x24 XFER DN 48°Wx24 °Dx36 °H RA PLENUM 24x18 RA UP 48x36 RETURN NR GRILLE, LOCATE TOP AT 2° BE OW COLING (3 TYP) 0 O 1- 20 0 100 (10 TYP) 0 2 - 1 - 2 -f 2 - 2 - 0 2 - CEILING ING MOUNTED SPACE STATIC PRESS RE SENSOR TO MODULAI EXHAUST FAN VFD TO MAINTAIN ( +.051WG) ABOVE FACTORY. 7J T -STAT WIRING / '1'T0 1U -201 0 / 12 FT. (FSG -2) CENTERED ON COMPUTER RACKS --� T -STAT WIRING ,� J`, C3 TO teigel 1,250 1,250 1 0 0 0 81 90 (8 TYP) O O 0 2 HVAC PLAN - LEVEL 2 SCALE: 1/4' =l' -0' 1 2 - 2 2 2 - 2 2 Vt P-7- 06ro 1 - 1 2 - 2 - 2 - 2 REVIEWED FOR ODE COMPLIANCE APPROVED MAY 11 2012 City of Tukwila BUILDING DIVISION 1 NORTH ARROW REcov ) CITY OF TUKWILA APR 1 3 2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SYM A REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE PERMIT PLANS UMC 04/13/12 ffEn NG° o'— ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED DATE 03 -14 -12 SUBTITLE HVAC PLAN - LEVEL 2 CURRENT REVISION SYMBOL DATE A 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9- 101BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET M221 JOB NO. COMP NO. DWG NO. 9- 101 -M221 1:48 PM f: \acad\ engineering \5761 \sheets \m230.dwg STEVE BUELER U.2 24x18 DN TO 481Wx24'Dx36°H RETURNINR PLENUM 18x24 1 30x24 2 — 2 2 1— BALANCE —RA DUCTWORK WE 11 / VOLUME DAMPERS (4 TYP.). —/ LOCATE VOLUME DAMPERS TO THEY ARE ACCESSIBLE FROM ROOF rj° 01 STANDPIPE BY OTHERS F R INDIRECT CONDENSATE CONNECTION INSULATE ALL DUCTWORK WITHIN FACTORY ENVIRONMENT WATH R -7 INSULATION, PER 200$ WSEC. 20x16 RA DN LJ r CONDENSATE DN TO STAND PIPE 84x60 OSA INTAKE LOUVER, WM-I MINIMUM 50% FREE AREA. LOUVER PROVIDED do INSTALLED BY G.C. i 1 i — 1 , INSULATED CONDENSATE LIE DOWN WASTE CONNECTION` ! 26x24 - 24x18 DN TO 481Wx24'Dx361H RETURN NR PLENUM GC TO PROVIDE OPENING IN HAN RAIL FOR RETURN NR DUCT — 2 — 2 — — 2 — — — 2 — 2 — 2 — 2 —f 2 2 — 50x20 RA UP TO ACU -1 VAir va,v /kVA V417 ACU -1 • M INSULATAED OSA DUCT r o-1r -.Ia 2 — 2 0 2 0 HVAC PLAN - ROOF LEVEL SCALE: 1/4' =1' -0' 2 -171 2 2 — 2 — 2 — M�I.1-o(0 h 2 — 2 — 2 — 2 REVIEWED FOR CODE COMPLIANCE (APPROVED MAY 11 2012 Ify of Tukwila BUI DING DIVISION NORTH ARROW 0 RECEivkt) CITY OF TUKWILA APR 1,;3 2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SYM A REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE PERMIT PLANS UMC 04/13/12 Q� Ey" NG° ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED DATE 03 -14 -12 SUBTITLE HVAC PLAN - ROOF LEVEL CURRENT REVISION SYMBOL DATE A 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9- 101BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET M230 JOB NO. COMP NO. DWG NO. 9- 101 -M230 1:48 PM f: \acad\ engineering \5761 \sheets \m301.dwg 0 STEVE BUELER SUPPORT HANGER BAND FROM STRUCTURE MINIMUM RADIUS OF (1) *(FLEX DIA) NOTE: ALL SUPPLY AIR DUCTWORK TO BE INSULATED DOWN TO AND INCLUDING DIFFUSER NECK, UNLESS OTHERWISE INDICATED. FLEXIBLE DUCT CONNECTION (6' -0" MAXIMUM LENGTH). SAME SIZE AS DIFFUSER NECK UNLESS NOTED OTHERWISE. DIFFUSER NECK, SIZE AS NOTED ON PLAN. PROVIDE SEALANT AT ALL FLOOR PENETRATIOS MODULAR DIFFUSER CEILING, SEE ARCH PLANS 1 CEILING DIFFUSER DETAIL \ M301 SCALE: NONE VAV BOX DISCHARGE PLENUM FLEXIBLE CONNECTION (TYPICAL 2) INSTALL VAV BOX HIGH AS POSSIBLE. DON'T LOCATE UNIT ABOVE LIGHT FIXTURE. \ \ / / \ / \__� FLOOR ABOVE COOLING ONLY (VAV)BOX CONTROLS ENCLOSURE SEE NOTE 1 NOTES: 1. POSSIBLE HEATING COIL, SEE PLANS AND SCHEDULES. CONFIRM CLEAR ACCESS REQUIREMENTS WITH SUBMITTAL. (4) HANGER STRAPS PRIMARY AIR INTAKE � COOLING ONLY SOLO/AV) BOX INSTALLATION DETAIL SCALE: NONE DRAIN LINE SHALL BE AT LEAST THE SAME SIZE AS THE NIPPLE ON THE DRAIN PAN PITCH DOWN TOWARD DRAIN OPEN DRAIN DESIGNER'S NOTE: UNIT TYPE A B DRAW THRU 2" [51 mm] PLUS X X BLOW THRU 1" [25mm] MINIMUM 2X WHERE X = STATIC PRESSURE IN PAN DRAIN PAN CONDENSATE DRAIN SIZING CRITERIA SCALE: NONE INSIDE CLEAR DIMENSION SAME SIZE AS GRILLE SHEET METAL BOOT- PROVIDE SEALANT AT ALL FLOOR PENETRATIOS 1 j OPEN DUCT CEILING - SEE ARCHITECTURAL DRAWINGS CEILING RA GRILLE CEILING RETURN AIR BOOT M301 SCALE: NONE x AVOID DIFFUSER TAPS AT END OF DISCHARGE PLENUM SPIN -IN OR EQUIV. FITTING WITH VOLUME DAMPER (TYPICAL) - LOW PRESSURE FLEX DUCT TO MATCH DIFFUSER NECK SIZE- X SEE NOTE 6(TYPICAL) SEE SA DIFFUSER - CONNECTION DETAIL (TYPICAL) SEE NOTE 2 WRAPPED DUCTWORK (TYPICAL) x NOTES: 1. NOT USED �- FAN TERMINAL (VAV)BOX /- SEE NOTE 3 AND 4 :MI111111I SEE NOTE 5 ELECTRICAL CLEARANCE REQUIRED. SEE SUBMITTAL AND ELECTRICAL CODE FOR REQUIREMENTS 2. MINIMUM 5' -0" BEFORE FIRST BRANCH DUCT TAKE -OFF FOR UNITS 2000 CFM AND SMALLER AND MINIMUM 10' -0" FOR UNITS LARGER THAN 2000 CFM. 3. PROVIDE SOUND LINED RETURN AIR BOOT AS SHOWN. 4. RETURN AIR DUCT AND RETURN AIR OPENING EQUAL IN SIZE TO RETURN AIR INLET TO BOX. FASTEN RETURN AIR BOOT TO STRUCTURE WITH WIRE. 5. MINIMUM OF 3' -0" STRAIGHT DUCT ON BOX INLET. MAXIMUM OF 5' -O" OF FLEXIBLE DUCT. INSULATE ALL DUCTWORK PER INSULATION SCHEDULE. 6. SHEET METAL DIFFUSER RUNOUT. SIZE TO MATCH DIFFUSER NECK SIZE. � (VAV)BOX FAN DETAIL SCALE: NONE PRIMARY SYSTEM SUPPLY AIR SYM REVISION A PERMIT PLANS BY UMC APPROVED DATE SYM REVISION BY APPROVED DATE 04/13/12 Q�BOE /NG° ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED 8 -3/4" FLOOR PENETRATION BY G.C. SUPPORT HANGER BAND FROM STRUCTURE ABOVE ADJUSTABLE FLOOR SUPPLY DIFFUSER CARPET RETENTION FLANGE w 1111111111111111111111111M 12x12 SUPPLY PLENUM IMF 11/ PROVIDE SEALANT BETWEEN PLENUM AND CORRUGATED DECKING DUST & LIQUID CATCH BASIN 12x12 SUPPLY PLENUM UNDERFLOOR SUPPLY DIFFUSER M301 SCALE: NONE f 2ND FLOOR , \—/ \—% \_ \—/ \—/ \ CONTROLS ENCLOSURE DRAMWN N CHECKED SERIES FAN POWERED (VAV)BOX VAV BOX DISCHARGE /' PLENUM / \r ��- (4) 1/2" ALL THREAD HANGER RODS SERIES FAN POWERED (VAV)BOX VAV BOX DISCHARGE PLENUM /_ INTERSTITIAL FLOOR DATE 03 -14 -12 FASTEN UNITSTRUT TO STRUCTURE ABOVE WITH SCREWS AND WASHERS NEOPRENE PAD MP.) fUNISTRUT FRAME BY UMC NEOPRENE HANGER (TYP) (VAV)BOX FAN DETAIL M301 SCALE: NONE FASTEN UNITSTRUT FRAME TO FLOOR WITH SCREWS AND WASHERS REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11.2012 City of Tukwila BUILDING DIVISION SUBTITLE MECHANICAL DETAILS CURRENT REVISION Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. CITY OF TUKV 11tH APR 1.3 2012 PERMIT CENT, R SYMBOL A DATE 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9- 101BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET M301 JOB NO. COMP NO. DWG NO. 9- 101 -M301 1:48 PM f: \acad\ engineering \5761 \sheets \m302.dwg N N STEVE BUELER (j v1 48x18 QS■ PLENUM GC TO PROVIDE OPENING IN HAND RNL FOR RETURN NR DUCT ON 2 0 84x60 OSA INTAKE LOUVER, WITH MINIMUM 50% FREE AREA LOUVER PROVIDED & INSTALLED BY G.C. 30x48 OSA CV 1 ••s 24x18 RA DUCT 24x30 RA DUCT 2¢x26 RA DUCT GC TO PROVIDE OPENING IN HAND RNL FOR SA DUCT SPRING CURB BY MC FOR VIBRATION ISOLATION GC TO PROVIDE SUB - STRUCTURE TO ELEVATE ACU -1 TO ALLOW FOR RETURN DUCT CONNECTION AT BOTTOM OF UNIT LL T 1 • F--4 - 1:::. 1 17 \I 1 24x18 RA DUCT r- -8' -6" CEILING- w cr 24x24 XFJ DUCT 6 a N 1IL r 80 BREAK ROOM EXHAUST, PROVIDE SCREEN OVER OPENING N MECHANICAL ELEVATION M302 SCALE: 1/4=1'-0' SYM A REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE PERMIT PLANS UMC 04/13/12 ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11 2012 City of Tukwila BUILDING DIVISION NORTH ARROW R CEIVEW .. CITY OF TUKIMLA APR 13 2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. DATE 03 -14 -12 SUBTITLE MECHANICAL ELEVATION VIEW CURRENT REVISION SYMBOL A DATE 03 -14 -2012 APPROVED BY DEPT. DATE ENGINEER MSH CHECKED APPROVED APPROVED TITLE IDS OFFICE TOWER /CONTROL ROOM BUILDING 9- 101BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET M302 JOB NO. COMP NO. DWG NO. 9- 101 —M302 84x60 OSA INTAKE LOUVER, WITH MINIMUM 50% FREE AREA LOUVER PROVIDED & INSTALLED BY G.C. — INSULATED 30x48 OSA DUCT 30x48 OSA 18x24 DN 48"Wx24 Dx361H RETURN NR PLENUM 48x18 OSA PLENUM 34x24 44x24 N SPRING CURB BY MC FOR VIBRATION ISOLATION GC TO PROVIDE SUB- STRUCIJRE TO ELEVATE ACU -1 TO ALLOW F R RETURN DUCT CONNECTION AT BOTTO OF UNIT 34x24 SA DUCT, SEE INTERSTITIAL PLAN FOR DUCT LAYOUT r-' v MIOb REVIEWED FOR CODE COMPLIANCE APPROVED MAY 11 2012 City of Tukwila BUILDING DIVISION NORTH ARROW RECENkt) ,. CITY OF TUKWILA APR 1 S 2012 PERMIT CENTER Legal: THIS DRAWING AND THE DESIGN HEREIN ARE THE PROPERTY OF UNIVERSITY MECHANICAL CONTRACTORS, INC. FOR THEIR USE IN CONSTRUCTION OF THIS PROJECT. NO OTHER USE SHALL BE PERMITTED WITHOUT THE WRITTEN CONSENT OF UNIVERSITY MECHANICAL CONTRACTORS, INC. SYM REVISION BY APPROVED DATE SYM REVISION BY APPROVED DATE A PERMIT PLANS UMC 04/13/12 Rt.E /NGm v�- ACCEPTABILITY THIS DESIGN AND /OR SPECIFICATION IS APPROVED DRAWN UMC CHECKED DATE 03 -14 -12 APPROVED SUBTITLE MECHANICAL ELEVATION VIEW CURRENT REVISION SYMBOL DATE 03 -14 -2012 IDS OFFICE TOWER /CONTROL ROOM BUILDING 9- 101BTE TEST FRAME PORTAKING BUILDING SYSTEMS /PK STRUCTURES TUKWILA, WA SHEET M303 JOB NO. COMP NO. DWG NO. 9- 101 -M303