HomeMy WebLinkAboutPermit M13-014 - EDGEWOOD APARTMENTS - UNITS 2 & 44 - ALTERATIONEDGEWOOD APTS
UNITS 2 & 44
3730 S 148 ST
M13-014
City okukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206-431-3670
Inspection Request Line: 206-431-2451
Web site: http://www.TukwilaWA.gov
MECHANICAL PERMIT
Parcel No.: 0040000900
Address: 3730 S 148 ST TUKW
Project Name: EDGEWOOD APTS - UNITS 2 & 44
Permit Number: M13-014
Issue Date: 01/17/2013
Permit Expires On: 07/16/2013
Owner:
Name: EDGEWOOD APARTMENTS LLC
Address: 830 168TH PL SE , BELLEVUE WA 98008
Contact Person:
Name: MOHAMMAD AMINPOUR
Address: 3730 S 148 ST - OFFICE , TUKWILA WA 98168
Email: AMINPOUR@COMCAST.NET
Phone: 206-353-7857
Contractor:
Name: OWNER AFFIDAVIT - MOHAMMAD AMINPOUR Phone:
Address:
Contractor License No:
Expiration Date:
DESCRIPTION OF WORK:
UNITS 2 & 44
ADDING WASHER/DRYER TO THE UNITS (STACKS OF 2 UNITS)
DRYER EXHAUST AND LAUNDRY ROOM VENTILATION FAN EXHAUST
Value of Mechanical: $150.00
Type of Fire Protection: UNKNOWN
Electrical Service Provided by:
Permit Center Authorized Signature:
Fees Collected:
$120.75
International Mechanical Code Edition: 2009
Date: 1'1.7— ( 3
I hereby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances
governing this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating
construction or the performance of work. I am authorized to sign and obtain this mechanical permit and agree to the conditions on the
back of this permit.
Signature:
Print Name.
k dlM ',tot 4-4/ ."(146/1/ -
This
( b' /'This permit shall become null and void if the work is not commenced within 180 days from the date of issuance, or if the work is suspended
or abandoned for a period of 180 days from the last inspection.
Date: 1 '—) 7 -- 'c
Drinfnrl• n1_l7_3n z
. •
PERMIT CONDITIONS
Permit No. M13-014
1: ***BUILDING DEPARTMENT CONDITIONS***
2: No changes shall be made to the approved plans unless approved by the design professional in responsible charge and the
Building Official.
3: All mechanical work shall be inspected and approved under a separate permit issued by the City of Tukwila Permit Center
(206/431-3670).
4: All permits, inspection records, and approved plans shall be at the job site and available to the inspectors prior to
start of any construction. These documents shall be maintained and made available until final inspection approval is
granted.
5: All construction shall be done in conformance with the approved plans and the requirements of the International
Building Code or International Residential Code, International Mechanical Code, Washington State Energy Code.
6: Remove all demolition rubble and loose miscellaneous material from lot or parcel of ground, properly cap the sanitary
sewer connections, and properly fill or otherwise protect all basements, cellars, septic tanks, wells, and other
excavations. Final inspection approval will be determined by the building inspector based on satisfactory completion of
this requirement.
7: Manufacturers installation instructions shall be available on the job site at the time of inspection.
8: All construction noise to be in compliance with Chapter 8.22 of the City of Tukwila Municipal Code. A copy can be
obtained at City Hall in the office of the City Clerk.
9: All plumbing and gas piping work shall be inspected and approved under a separate permit issued by the City of Tukwila
Building Department (206-431-3670).
10: All electrical work shall be inspected and approved under a separate permit issued by the City of Tukwila Building
Department (206-431-3670).
11: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an approval of,
any violation of any of the provisions of the building code or of any other ordinances of the City of Tukwila. Permits
presuming to give authority to violate or cancel the provisions of the code or other ordinances of the City of Tukwila
shall not be valid. The issuance of a permit based on construction documents and other data shall not prevent the
Building Official from requiring the correction of errors m the construction documents and other data.
rine IMC -4/1(1 M13-014
Printer (11.17-7n13
CITY OF TUKVI1
Community Development Department
Permit Center
6300 Southcenter Blvd., Suite 100
Tukwila, WA 98188
http://www.TukwilaWA.gov
Mechanical Permit No. t't. R 0 I
1-(
Project No.
(For office use only)
MECHANICAL PERMIT APPLICATION
Applications and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or by fax.
**please print**
SITE LOCATION
King Co Assessor's Tax No.: 06 110 00 — 0 9 9v
Site Address: 373 d s. )--4 249Suite Number: Floor:
Tenant Name:
Property Owners Name:
Mailing Address:
E 4-peAi- 441, LL
New Tenant: 0 Yes ❑ .. No
ty
State
Zip
CONTACT PERSON — who do we contact when your permit is ready to be issued
Name: 1 o kaim
Mailing Address: 3730 s o .147* 5 .ve,0 ellti-�a"
E -Mail Address:coiii'hrovr- a comedst. „Lt.
Day Telephone: (2o) 35-3— 7f ' S7
w
City State ��
Zp
Fax Number: (zits) Sol -1 47
MECHANICAL CONTRACTOR INFORMATION
Company Name:
Mailing Address:
City
Contact Person: Day Telephone:
E -Mail Address: Fax Number:
Contractor Registration Number:
State
Zip
Expiration Date:
ARCHITECT OF RECORD — All plans must be stamped by architect :of record
Company Name:
Mailing Address:
City
Contact Person: Day Telephone:
E -Mail Address: Fax Number:
State
Zip
ENGINEER OF RECORD — All plans must be stamped by engineer of record
Company Name:
Mailing Address:
City
Contact Person: Day Telephone:
E -Mail Address: Fax Number:
State
Zip
H:\Applications\Porms-Applications On Line\2010 Applications\7-2010 - Mechanical Permit Application.doc
Revised: May 2011
bh
Page 1of2
IP
Valuation of project (contractor's bid price): $ r 5-0
Scope of work (please provide detailed information):
010
ryw- v'evA--s 4 f.o.i x1/441 ry r19 -or.. yQv -s
Use: Residential: New 0
Commercial: New 0
Replacement
Replacement
Fuel Type: Electric ld Gas 0
Other:
Indicate type of mechanical work being installed and the quantity below:
Unit Type:
Qty
Unit Type:
Qty
Unit Type:
Qty
Bioler/Compressor .
0-3 hp/100,000 btu
Qty
furnace <100k btu
air handling unit
>10,000 cfm
fire damper
furnace >100k btu
evaporator cooler
diffuser
3-15 hp/500,000 btu
floor furnace
ventilation fan connected
to single duct
s�
d
thermostat
15-30 hp/1,000,000
btu
suspended/wall/floorventilation
mounted heater
system
wood/gas stove
30-50 hp/1,750,000
btu
appliance vent
oC _
hood and duct
emergency
generator
50+ hp/1,750,000 btu
repair or addition to
heat/refrig/cooling system
Incinerator — domestic
other mechanical
equipment
air handling unit <10,000
cfm
incinerator — comm/ind
PERMIT APPLICATION NOTES -
Value of construction — in all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject
to possible revision by the permit center to comply with current fee schedules.
Expiration of plan review — applications for which no permit is issued within 180 days following the date of application shall expire by limitation.
The building official may grant one extension of time for additional periods not to exceed 90 days each. The extension shall be requested in writing
and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition).
I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER
PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT.
BUILDING OWNER OR AUTHORIZED AGENT:
Signature:./ di
Print Name:
rick twt,"a01 Asiirnecur
Mailing Address:
Date: -- — 3
Day Telephone: (ad
) 3 S3 7f5 7
j
City Zip
Date Application Accepted:
Date Application Expires:
Staff Initials:
H:\Applications\Forms-Applications On Line\2010 Applications\7-2010 - Mechanical Peradt Application.doc
Revised: May 2011
bh
Page 2 of 2
•
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206-431-3670
Fax: 206-431-3665
Web site: http://www.TukwilaWA.gov
Parcel No.: 0040000900
Address: 3730 S 148 ST TUKW
Suite No:
Applicant: EDGEWOOD APTS
RECEIPT
Permit Number: M13-014
Status: PENDING
Applied Date: 01/09/2013
Issue Date:
Receipt No.: R13-00128
Payment Amount: $120.75
Initials: WER Payment Date: 01/09/2013 02:23 PM
User ID: 1655 Balance: $0.00
Payee: ARASH AMINPOUR
TRANSACTION LIST:
Type Method Descriptio Amount
Payment Credit Crd VISA
Authorization No. 07114G
ACCOUNT ITEM LIST:
Description
120.75
Account Code Current Pmts
MECHANICAL - NONRES
PLAN CHECK - NONRES
000.322.102.00.00 96.60
000.345.830 24.15
Total: $120.75
e.isIcsa• na no oni�
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO. :'PERMIT:NO:
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila: WA 98188 _ (206) 431-3670
Permit Inspection Request Line (206) 431-2451
Project_..
iftb.-&e-ut,)a
Type of Inspection:
-IM"A, :
:f
Address:—.
3 0 ( 4 -et,
Date Called:
Special Instructions:
_,r
`
'
Date Wanted:
/
,..a.m:.
P.m:
Requester:
Phone No:
Approved per applicable codes.
COMMENTS:
1\ 0-
�� f-4
DK- wJ3
Corrections required prior to approval.
() - (Lu4((
Inspect?r: (I P
V
n REINSPECTION FEE REQUIRED. Prionto next inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call to schedule,. reinspection.
•
Date:-
-
ate
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO. PERMIT NO. ie
CITY OF TUKWILA BUILDING DIVISION -
6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670
Permit Inspection Request Line (206) 431-2451 {.
Proj��ct:
t -Wl)O % P (S
Type of Inspection:
v �i..->•�J' •Ck:e
Address:
110 1� ,� sr
Date Called:
Special Instructions: I ``�'"�
P2.__41-
Date Wanted:.
F
a.m.
Requester:
,
Ph 1 �o
3s3.
�1
' ...-7
Approved per applicable codes.
1
Corrections required prior to approval.
COMMENTS:
y A
0I - '44-
A-
A M,c 6 -kQ n A 44--- JA: r,
j,
v P (Ji')r-4( . c=-'
Inspec or:
triA )j/1
i1
T7 REINSPECTION FEE REQUIRED. Prior to next inspection, fee -must be
paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection.....
Date..
5t0 o 0-
ems For- M
P
GTUN275EM/GM
GE° 27" Unitized Spacemaker° 3.4 DOE Cu. Ft.
Dimensions and Installation Information (in inches)
Electrical Requirements:
GTUN275EM Electric Dryer - This appliance should be connected to an
individual, properly -grounded branch circuit with 120/240V or 120/208V
single-phase 60 Hz electrical service and should be protected by
30 -amp time -delay fuses or circuit breakers KW Rating per voltage
(240/208). This appliance is manufactured with neutral connected to the
frame. Power cord should be purchased separately.
Note:
These appliances are not approved for 120 -volt operation.
Gas Requirements:
GTUN275GM Gas Dryer - This appliance should be connected to an
individual branch circuit with 120 -volt single-phase 60 Hz electrical service
and should be protected by 20 -amp time -day fuses or circuit breakers.
This appliance is equipped with a 4 -foot long flexible U.S. listed 20 -amp
power cord to match a 20 -amp receptacle.
Note:
Gas Rated input 20,000 BTU/HR. Factory equipped for natural gas. Tested
for LP gas. LP gas supply requires a conversion kit. Have a qualified gas
technician install a conversion kit before use.
Dryers must be exhausted to the outside.
Installation Information:
For complete information, see installation instructions packed with
the product.
For answers to your Monogram,®GE Profile' or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
imagination at work
RECEIVED
CITY OF TUKWILA
FEB 0 6 2013
PERMIT CENTER
e66€ WO (0 eA
3 9 3 o (-4-g'm
-353 - 7Y57
Stainless Steel Washer and 5.9 Cu. Ft. Dryer
75.5'
52.9'
27.7'
0
••I 00
Vent
*26.7' ,r
t
18.6
12.5'
Woter inlets
lreorl
i.-- 2.9"
brain outlet
ireor)
—r
k— 3.9"
20.2" + t
Gas Inlet
(Reor view of appliance)
3'
1
26.8"
36.5'
51'
47"
4.35" —t►
30.85' ----►t
Listed by
Underwriters
laboratories
Specification Revised 6/12 360330
AM- DM
4614.1= 2745ENVG`M'
Lee -F-20,' Unitized Spacemaker° 3.4 DOE Cu. Ft. Stainless Steel Washer and 5.9 Cu. Ft. Dryer
Dimensions and Installation Information lin inches)
ila2170EM/G'MAa nd-GTUNN 275,EM4Q1
sDIKEWNA,USfoLENGTH :-
For answers to your Monogram,®GE Profile' or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
imagination at work
For complete information, see installation instructions packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal
duct cannot be used, then UL -listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special
installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil -type) duct.
A UL -listed flexible metal (foil -type) duct may be used ONLY in installations where rigid metal or flexible metal
(semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length
of the transition duct. Please see installation instruction packed with your dryer for complete instructions when
using flexible metal (foil type) ducting.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer,
add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn
over 45° should be treated os o 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl
space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage.
Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap
must also be located at least 12" above the ground or any other obstruction with the opening pointed down.
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side and rear
1" front and top
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 76-1/2:'
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area
equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in.
of open area equally distributed.
• No other fuel -burning appliance shall be installed in the same closet with a gos dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the National Electric
Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" either side and rear
1" front and top
Listed by
Underwriters
Laboratories
Specification Revised 6/12 360330
RECOMMENDED MAXIMUM LENGTH
Exhaust Hood Types
Recommended
Use only for short
run installations
4" DIA
0
M
4" DIA
40,....„.,;:;:
4" DIA.
,o
N,o. of 90°
illiElbows
Rigid
Metal
Rigid
Metal
0
CIP
56 Feet
42 Feet
3
VAMP) )
2:5 Fedt>
ee
ee
For answers to your Monogram,®GE Profile' or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
imagination at work
For complete information, see installation instructions packed with your dryer.
Ducting Materials:
For best performance, this dryer should be vented with 4" diameter all rigid metal exhaust duct. If rigid metal
duct cannot be used, then UL -listed flexible metal (semi-rigid) ducting can be used (Kit WX08X10077). In special
installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil -type) duct.
A UL -listed flexible metal (foil -type) duct may be used ONLY in installations where rigid metal or flexible metal
(semi-rigid) ducting cannot be used AND where a 4" diameter can be maintained throughout the entire length
of the transition duct. Please see installation instruction packed with your dryer for complete instructions when
using flexible metal (foil type) ducting.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the side or bottom of dryer,
add one turn.
2. The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated is shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn
over 45° should be treated os o 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl
space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage.
Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint
and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap
must also be located at least 12" above the ground or any other obstruction with the opening pointed down.
Special Installation Requirements
Alcove or Closet Installation:
• If your dryer is approved for installation in an alcove or closet, it will be stated on a label on the dryer back.
• The dryer MUST be exhausted to the outside.
• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:
0" either side and rear
1" front and top
• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 76-1/2:'
• Closet doors must be louvered or otherwise ventilated and must contain a minimum of 60 sq. in. of open area
equally distributed. If this closet contains both a washer and a dryer, doors must contain a minimum of 120 sq. in.
of open area equally distributed.
• No other fuel -burning appliance shall be installed in the same closet with a gos dryer.
Bathroom or Bedroom Installation:
• The dryer MUST be exhausted to the outdoors.
• The installation must conform with the local codes, or in the absence of local codes, with the National Electric
Code and National Fuel Gas Code, ANSI Z223 for gas dryers.
Minimum Clearances other than Alcove or Closet Installation:
• Minimum clearances to combustible surfaces
0" either side and rear
1" front and top
Listed by
Underwriters
Laboratories
Specification Revised 6/12 360330
GTUN275EM/GM
GE° 27" Unitized Spacemaker° 3.4 DOE Cu. Ft. Stainless Steel Washer and 5.9 Cu. Ft. Dryer
Features and Benefits
• 3 wash/spin speed combinations - Speeds are matched to fabric type
for great clothes care
• 9 wash cycles - Cycles are designed to specifically handle various
fabrics and soils
• Auto -load sensing with 5 water levels Washer will automatically
measure the load size and add just the right amount of water
• Bleach and fabric softener dispensers - Solutions are automatically
mixed withwash water for clean, bright, soft -to -the -touch results
• Rotary -electronic controls (washer) - Simplify cycle selection
• Cycle status lights - Provide accurate cycle times
• Rotary -electromechanical controls (dryer) - Allow fast, easy cycle
selection
• Stainless steel washer basket - Long-lasting stainless steel finish
resists rust and won't chip, peel or snag clothes
• Model GTUN275EMWW - White on white (Electric)
• Model GTUN275GMWW - White on white (Gas)
imagination at work
Modified Energy Factor (MEF)
2.02
Water Factor (WF)
5.65
ENERGY STAR
As an ENERGY STAR®
partner, GE has determined
that this product meets the
ENERGY STAR guidelines
for energy efficiency.
Specification Revised 6/12 360330
1
REVISIONS
No changes shall bo mado to thea scope
of work without prior approval of
Tukwila Building Division.
NOTE: Revisions will require a new plan submittal
and may include additional plan review fees.
SEPARATE PERMIT I
REQUIRED FOR:
Electrical
Plumbing
at Gas Piping
City of Tukwila
BUILDING DIVISION
PROJECT INFORMATION
Parcel Number
004000-0900
Name
EDGEWOOD APARTMENTS LLC
Site Address
3730 S 148TH ST 98168
Legal
ADAMS HOME TRS POR OF S 30 FT OF LOTS 10 & 11 &
W 1/2 OF LOT 23 & ALL OF LOT 24 & POR OF LOTS 25 &
26 LESS POR SD LOTS 10 & 25 & 26 LY WLY & NLY OF
FOLG DESC LINES - BAAP ON N LN OF S 30 FT OF SD •
LOT 10 LY 120 FT ELY OF PACIFIC HWY S TH S PLW SD.
HWY 200 .FT TH W PLW N LN SD LOTS 25 & 26 TO ELY
MGN OF SD HWY & TERMINUS OF LN DESC LESS E 88
FT OF SD LOT 11 LESS S 10 FT OF SD LOT 24 & OF W
1/2 OF LOT 23 LESS RD
CONTACT/OWNER
MOHAMMAD AMINPOUR
425-502-9146
3730 S 148TH ST
TUKWILLA, WA 98168
TABLE OF CONTENTS
A1.1 SITE PLAN
A2.1 FIRST FLOOR PLAN
A2.2 SECOND FLOOR PLAN
A2.3 THIRD FLOOR PLAN
A2.4 CRAWL SPACE PLUMBING PLAN
A3.1 EXTERIOR ELEVATIONS
A3.2 RISER DIAGRAM
VICINITY MAP
REVIEWED FOR
CODE COMPLIANCE
APPROVED
JAN 16 2013
f -T
City of u iia
BUILDING ISION
FIELD COPY
Perm Ns,
This set of construction documents shall
be kept at the site of work and shall be
open to inspection by the Building Official
or a duly authorized representative.
City Of Tukwila BUILDING
Washer/Dryer Addition
Edgewood Apartments
12-27-12 3730 S 148th St. Tukwilla WA 98168
O lH
A0.0
RECEIVED
('F Tll4(1,R!!S
JAN O 6 t,;3
"it:IRMIT CENTER
/
S 146th St 99
b
S 148th
SITE
St X
I
VICINITY MAP
REVIEWED FOR
CODE COMPLIANCE
APPROVED
JAN 16 2013
f -T
City of u iia
BUILDING ISION
FIELD COPY
Perm Ns,
This set of construction documents shall
be kept at the site of work and shall be
open to inspection by the Building Official
or a duly authorized representative.
City Of Tukwila BUILDING
Washer/Dryer Addition
Edgewood Apartments
12-27-12 3730 S 148th St. Tukwilla WA 98168
O lH
A0.0
RECEIVED
('F Tll4(1,R!!S
JAN O 6 t,;3
"it:IRMIT CENTER
REVIEWED FOR
CODE COMPLIANCE
APPROVED
JAN 16 2013
City of Tukwila
BUILDING DIVISION
EXIST
PARKING
S 148T1--1 ST
SITE PLAN
II= 50'-0'
Washer / Dryer Addition
Edgewood Apartments
12-27-12 3730 S 148th St. Tukwilla WA 98168
004s: ;32 Lt1
A1.1
RECEIVED
CITY OF TUKWILA
JAN 0 9 2013
PERMIT CEN'"1R
Patio
1
Living
Dining
Kit
Br 1
O
Two Story Apt Floor 1
Scale: 1/4" = 1'-0"
Washer /Dryer Addition
Edgewood Apartments
12-27-12 3730 S 148th St. Tukwila WA 98168
REVIEWED FOR
CODE COMPLIANCE
APPR, @QED
JAN 16 2013
City of Tukwila
BUILDING DIVISION
A2.1
RECEIVED
CITY OF TUKWILA
JAN 0 9 2013
PERMIT CENTER
Deck
Br 3
Bath
Br 2
If'
dl
Two Story Apt Floor 2
Scale: 1 /-4" = 1'-0"
h
Laundr
Washer / Dryer Addition
Edgewood Apartments
12-27-12 3730 S 148th St. Tukwilla WA 98168
REVIEWED FOR
CODE COMPLIANCE
APPROVED
JAN 16 2013
City of Tukwila
BUILDING DIVISION
50 CFM FAN
CEILING MOUNT
SEE A2.3 FOR
ADDITIONAL
NOTES
A2.2
RECEIVED
CITY OF TUKWILA
JAN 0 9 2013
PERMIT CLN E�-
REVIEWED FOR—
CODE COMPLIANCE
APPROVED
JAN 16 2013
City of Tukwila
BUILDING DIVISION
Deck
_1K
Dining
Living
Kit
50 CFM FAN
CEILING
MOUNT
NON RATED _
DUCT CHASE
BELOW EXIST
RATED
CEILING
Br 1
rIF
r�r
NEW
WASHER/ DRYER
Bath
One Story Apt Floor 3
Scale: 1/4" = 1'-0"
Washer /Dryer Addition
Edgewood Apartments
12-27-12 3730 S 148th St. Tukwilla WA 98168
4" X 30GA
DRYER DUCT
W WALL CAP
NO SCREEN
4"X30GA
FAN DUCT W/
WALL CAP
A2.3
RECEIVED
CITY OF TUKWILA
JAN 0 9 2013
PERMIT CEN"f :R
REVIEWED FOR
CODE COMPLIANCE
APPROVED
JAN 16 2013
City of Tukwila
BUILDING DIVISION
TO SIDE SEWER
4"
4"
TO SIDE SEWER 4"
LEGEND
NEW
EXISTING - - - - -
r---
1u
'
"
-
2"�
I
1
'E
n
r
71-r7r 747-
co
2 '
c'.
mommimi
1
1�
.J4"
2°�
CO
i
�
r
u
n
/------
4"CO
�
Thi
—
Typical Partial Plumbing Plan
Scale: 1" = 10 ft
Washer/Dryer Addition
Edgewood Apartments
12-27-12 3730 S 148th St. Tukwilla WA 98168
A2.4
RECEIVED
CITY OF TUKWILA
JAN 0 9 2013
PERMIT CENTEF,
REVIEWED FOR
CODE COMPLIANCE
JAN 16 2013
City of Tulcwriia
BUILDING DIVISION
3RD FL.
2ND FL.
IST FL.
a31N33 111A13d
IIIII!!IIIII
111111111111
3RD FL
m
N
m
ED
ED
I1
m
m
Li
1
m
ED
ED
m
EAST BLDG - WEST ELEV.
NO SCALE
2ND FL
IST FLS
El
m
m
J
lel
m
m
ED
15T FL.
n
m
TIMIT
WEST BLDG - WEST ELEV.
NO SCALE
m
m
m
ti
EAST BLDG- SOUTH ELEV.
NO SCALE
IIIIIIIIII
■■
r','ti "4�� h4
EXIST CHU
1
1
rri
3RD FL.
-
-
I
I
I
2ND FL.
-
15T FL.
n
m
TIMIT
WEST BLDG - WEST ELEV.
NO SCALE
m
m
m
ti
EAST BLDG- SOUTH ELEV.
NO SCALE
IIIIIIIIII
■■
r','ti "4�� h4
EXIST CHU
ROOF
SUDS RELIEF IS FROM BOTTOM OF VERT TO HORIZ
J
VTR
L
J
VTR
L
2" V
2"V 2"V
"411- 3" V
1.5" V
SHOWER
THIRD FLOOR
2" V
SECOND
r
TOILET
2" V
1
CO
I� N�
2" W
FLOOR
3" W
NEW WASHER
BATHROOM
SINK
NEW WASHER
1.5" V
1.5" W
2" W
2" W
F
z
0
0
W
W
KITCHEN SINK
2" V
3" W
FIRST FLOOR
TOILET
BATHROOM SINK
2" W
3 BEDROOM UNIT
CRAWL SPACE
EXISTING 4"
Riser Diagram
Washer/Dryer Addition
Edgewood Apartments
12-27-12 3730 S 148th St. Tukwila WA 98168
REVIEWED FOR
co CODE COMPLIANCE
APPROVED
JAN 16 2013
City of Tukwila
BUILDING DIVISION
A3.2.
RECEIVED
CITY OF TUKWILA
JAN 092013
PERMIT CE6ITER
•
re t i c COPY
PLAN REVIEW ROUTING SLIP
ACTIVITY NUMBER: M13-014 DATE: 01-09-13
PROJECT NAME: EDGEWOOD APTS - UNITS 2 & 44
SITE ADDRESS: 3730 S 148 ST
X Original Plan Submittal
Response to Correction Letter #
Response to Incomplete Letter #
Revision # After Permit Issued
DEPARTMENTS:Bn'g
. 'DIvlslo" ' nd i ( n 7
I
Public Works ❑
Fire Prevention
Structural
n
Planning Division
Permit Coordinator
n
u
DETERMINATION OF COMPLETENESS: (Tues., Thurs.)
Complete
Comments:
Incomplete
DUE DATE: 01-10-13
Not Applicable
n
Permit Center Use Only
INCOMPLETE LETTER MAILED:
LETTER OF COMPLETENESS MAILED:
Departments determined incomplete: Bldg 0 Fire 0 Ping 0 PW 0 Staff Initials:
TUES/THURS ROUTING:
Please Route M Structural Review Required ❑ No further Review Required n
REVIEWER'S INITIALS: DATE:
APPROVALS OR CORRECTIONS:
Approved
Notation:
Approved with Conditions
DUE DATE: 02-07-13
Not Approved (attach comments) n
REVIEWER'S INITIALS: DATE:
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections:
Bldg 0 Fire 0 Ping 0 PW 0 Staff Initials:
Documents/routing slip.doc
2-28-02
CITY OF TUKWILA
Department of Community Development
6300 Southcenter Boulevard, Tukwila, WA 98188
Telephone: (206) 431-367o FAX (206) 431-3665
E-mail: tukplanpci.tukwila.wa.us
Permit Center/Building Division
206 431-3670
Public Works Department
206 433-0179
Planning Division
206 431-3670
AFFIDAVIT IN LIEU OF CONTRACTOR REGISTRATION
STATE OF WASHINGTON)
) ss.
COUNTY OF KING
h1 o Lam w.clai\ 41,),.), 626cy ✓
[please print name]
, states as follows:
PERMIT NO: `l013
M�3-DIS
PG r -CX s
ELI3- 00,23
1. I have made application for a permit from the City of Tukwila, Washington.
2. I understand that state law requires that all building construction contractors be registered with the
State of Washington. The exceptions to this requirement are stated under Section 18.27.090 of the
Revised Code of Washington, a copy of which is printed on the reverse side of this Affidavit. I have
read or am familiar with RCW 18.27.090.
3. I understand that prior to issuance of a permit for work which is to be done by any contractor, the
City of Tukwila must verify either that the contractor is registered by the State of Washington, or that
one of the exemptions stated under RCW 18.27.090 applies.
4. In order to provide verification to the City of Tukwila of my compliance with this requirement, I
hereby attest that after reading the exemptions from the registration requirement of RCW 18.27.090,
I consider the work authorized under this permit to be exempt under number J3 , and will therefore
not be performed by a registered contractor.
5. I understand that the licensing provision of RCW 19.28.161 through 19.28.271 shall not apply to
persons making electrical installations on their own property or to regularly employed employees
working on the premises of their employer. The proposed electrical work is not for the construction
of a new building for rent, sale or lease.
I understand that I may be waiving certain rights that I might otherwise have under state law in any decision
to engage an unregistered contractor to perform construction work.
4._ L'll l
11,
isgroNctovii,-/-
oim.).efts)
Autsk.4-1
s02i
V$14149.410-19-
h.111% %%%%%%%% %%%%
.111
Signed and sworn to before me this
0 day of
, 2013 .
1.4.041 -RA,0
NOTARY PUBLIC in and for the State of Washington
Residing at - , County
Name as commissioned: (
02.1/ ' 1,�"rock
My commission expires: D
18.27.090 Exemptions. The reg ation provisions of this chapter do not apply AP
1. An authorized representative of the United States
government, the state of Washington, or any incorporated
city, town, county, township, irrigation district, reclamation
district, or other municipal or political corporation or
subdivision of this state;
2. Officers of a court when they are acting within the scope
of their office;
3. Public utilities operating under the regulations of the
utilities and transportation commission in construction,
maintenance, or development work incidental to their own
business;
4. Any construction, repair, or operation incidental to the
discovering or producing of petroleum or gas, or the
drilling, testing, abandoning, or other operation of any
petroleum or gas well or any surface or underground nine
or mineral deposit when performed by an owner or lessee;
5. The sale of any finished products, materials, or articles of
merchandise that are not fabricated into and do not become
a part of a structure under the common law of fixtures;
6. Any construction, alteration, improvement, or repair of
personal property performed by the registered or legal
owner, or by a mobile/manufactured home retail dealer or
manufacturer licensed under chapter 46.7o RCW who shall
warranty service and repairs under chapter 46.70 RCW;
7. Any construction, alteration, improvement, or repair
carried on within the limits and boundaries of any site or
reservation under the legal jurisdiction of the federal
government;
8. Any person who only furnished materials, supplies, or
equipment without fabricating them into, or consuming
them in the performance of, the work of the contractor;
9. Any work or operation on one undertaking or project by
one or more contracts, the aggregate contract price of
which for labor and materials and all other items is less
than five hundred dollars, such work or operations being
considered as of a casual, minor, or inconsequential nature.
The exemption prescribed in this subsection does not apply
in any instance wherein the work or construction is only a
part of a larger or major operation, whether undertaken by
the same or a different contractor, or in which a division of
the operation is made into contracts of amounts less than
five hundred dollars for the purpose of evasion of this
chapter or otherwise. The exemption prescribed in this
subsection does not apply to a person who advertises or
puts out any sign or card or other device which might
indicate to the public that he or she is a contractor, or that
he or she is qualified to engage in the business of
contractor;
10. Any construction or operation incidental to the
construction and repair of irrigation and drainage ditches
of regularly constituted irrigation districts or reclamation
districts; or to farming, dairying, agriculture, viticulture,
horticulture, or stock or poultry raising; or to clearing or
other work upon land in rural districts for fire prevention
purposes; except when any of the above work is performed
by a registered contractor;
11. An owner* who contracts for a project with a registered
contractor, except that this exemption shall not deprive the
owner of the protections of this chapter against registered
and unregistered contractors. The exemption prescribed in
this subsection does not apply to a person who performs
the activities of a contractor for the purpose of leasing or
selling improved property he or she has owned for less than
twelve months;
12.* Any person working on his or her own property,
whether occupied by him or her or not, and any person
working on his or her personal residence, whether owned
by hint or her or not but this exemption shall not apply to
any person who performs the activities of a contractor on
his or her own property for the purpose of selling,
demolishing, or leasing the property;
13. An owner* who performs maintenance, repair, and
alteration work in or upon his or her own properties, or
who uses his or her own employees to do such work;
14. A licensed architect or civil or professional engineer
acting solely in his or her professional capacity, an
electrician certified under the laws of the state of
Washington, or a plumber certified under the laws of the
state of Washington or licensed by a political subdivision of
the state of Washington while operating within the
boundaries of such political subdivision. The exemption
provided in this subsection is applicable only when the
person certified is operating within the scope of his or her
certification;
15. Any person who engages in the activities herein
regulated as an employee of a registered contractor with
wages as his or her sole compensation or as an employee
with wages as his or her sole compensation;
16. Contractors on highway projects who have been
prequalified as required by RCW 47.28.070, with the
department of transportation to perform highway
construction, reconstruction, or maintenance work;
17. A mobile/manufactured home dealer or manufacturer
who subcontracts the installation, set-up, or repair work to
actively registered contractors. This exemption only applies
to the installation, set-up, or repair of the
mobile/manufactured homes that were manufactured or
sold by the mobile/manufactured home dealer or
manufacturer;
18. An entity who holds ala.vid`electricasl,�c'ontractor's
license under chapter 0.28RC.W`tAtteempNysba certified
journeyman electrician, a certified residentual.specialty
electrician, or an eleefrica1trainee meetng.tz a
requirements of chapter 19.28 RCW to perform e umbing
work that is incident -ally, directly, and imnijjliate]y
appropriate to the like^iriikind replacemen�t�of apousehold
appliance or other small h tisehgldutili,ation equipment
that requires limited electr`io,pi erlan'd,lirnite'd waste
and/or water connection'A
s n'el'e6tri'cal ?rainee must be
supervised by a certified elects ciatVwl1ile performing
plumbing work.
• Per Washington State Department of Labor and Industries lessee has
been interpreted to be equivalent to owner for purposes of exemptions.