HomeMy WebLinkAboutPermit D14-0263 - POTATO CORNER - KIOSKPOTATO CORNER
2800 SOUTHCENTER MALL
K-1221
D14-0263
Parcel No:
Address:
City of Tukwila
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206-431-3670
Inspection Request Line: 206-438-9350
Web site: http://www.TukwilaWA.gov
DEVELOPMENT PERMIT
9202470010 Permit Number: D14-0263
2800 SOUTHCENTER MALL UnitK1221 Issue Date: 11/26/2014
Permit Expires On: 5/25/2015
Project Name: POTATO CORNER
Owner:
Name:
Address:
Contact Person:
Name:
Address:
Contractor:
Name:
Address:
License No:
Lender:
Name:
Address:
WESTFIELD PROPERTY TAX DEPT
PO BOX 130940 , CARLSBAD, WA,
92013
WILLIAM MILLHOLLIN
1026 SW 151 ST, BURIEN, WA, 98166
WESTMARK CONSTRUCTION INC
6102 N 9TH ST STE 400, TACOMA,
WA, 98406
WESTMCI012D3
FRANK SHAIKH
10107 ELMWOOD AVE , LUBBOCK, TX,
79424
Phone: (206) 601-7043
Phone:
Expiration Date:
DESCRIPTION OF WORK:
NEW TENANT KIOSK INSIDE SOUTHCENTER MALL. NEW KIOSK, FRAMED CEILING, ELECTRICAL AND PLUMBING
FOR FOOD SERVICE EQUIPMENT AND LIGHTING
Project Valuation: $20,000.00
Type of Fire Protection: Sprinklers:
Fire Alarm:
Type of Construction: IIB
Electrical Service Provided by: TUKWILA FIRE SERVICE
Fees Collected: $824.42
Occupancy per IBC: B
Water District: TUKWILA
Sewer District: TUKWILA SEWER SERVICE
Current Codes adopted by the City of Tukwila:
International Building Code Edition:
International Residential Code Edition:
International Mechanical Code Edition:
Uniform Plumbing Code Edition:
2012
2012
2012
2012
International Fuel Gas Code:
WA Cities Electrical Code:
WA State Energy Code:
2012
2014
2012
Public Works Activities:
Channelization/Striping:
Curb Cut/Access/Sidewalk:
Fire Loop Hydrant:
Flood Control Zone:
Hauling/Oversize Load:
Land Altering:
Landscape Irrigation:
Sanitary Side Sewer:
Sewer Main Extension:
Storm Drainage:
Street Use:
Water Main Extension:
Water Meter:
Volumes: Cut: 0 Fill: 0
Number: 0
No
Permit Center Authorized Signature: Date:
I hearby certify that I have read and xamir ed this permit and know the same to be true and correct. All
provisions of law and ordinances go rning this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provisions of any other
state or local laws regulating construction or the performance of work. I am authorized to sign and obtain this
development • and agree to the conditions attached to this permit.
Signa
Prin
Date: /J • ;c '
This permit shall become null and void if the work is not commenced within 180 days for the date of issuance, or if
the work is suspended or abandoned for a period of 180 days from the last inspection.
PERMIT CONDITIONS:
1: ***BUILDING PERMIT CONDITIONS***
2: Work shall be installed in accordance with the approved construction documents, and any changes made
during construction that are not in accordance with the approved construction documents shall be
resubmitted for approval.
3: All permits, inspection record card and approved construction documents shall be kept at the site of work
and shall be open to inspection by the Building Inspector until final inspection approval is granted.
4: All construction shall be done in conformance with the Washington State Building Code and the
Washington State Energy Code.
5: All food preparation establishments must have Seattle/King County Department of Public Health sign -off
prior to opening or doing any food processing. Arrangements for final Health Department inspection shall
be made by calling Seattle/King County Department of Public Health, (206/296-4928), at least three
working days prior to desired inspection date. On work requiring Health Department approval, it is the
contractor's responsibility to have a set of plans approved by the agency on the job site.
6: Fire retardant treated wood shall have a flame spread of not greater than 25. All materials shall bear
identification showing the fire performance rating thereof. Such identification shall be issued by an
approved agency having a service for inspection at the factory.
7: Remove all demolition rubble and loose miscellaneous material from lot or parcel of ground, properly cap
the sanitary sewer connections, and properly fill or otherwise protect all basements, cellars, septic tanks,
wells, and other excavations. Final inspection approval will be determined by the building inspector based
on satisfactory completion of this requirement.
8: Water heaters shall be anchored or strapped to resist horizontal displacement due to earthquake motion.
Strapping shall be at points within the upper one-third and lower one-third of the water heater's vertical
dimension. A minimum distance of 4-inches shall be maintained above the controls with the strapping.
9: All plumbing and gas piping work shall be inspected and approved under a separate permit issued by the
City of Tukwila Building Department (206-431-3670).
10: All electrical work shall be inspected and approved under a separate permit issued by the City of Tukwila
Permit Center.
11: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an
approval of, any violation of any of the provisions of the building code or of any other ordinances of the City
of Tukwila. Permits presuming to give authority to violate or cancel the provisions of the code or other
ordinances of the City of Tukwila shall not be valid. The issuance of a permit based on construction
documents and other data shall not prevent the Building Official from requiring the correction of errors in
the construction documents and other data.
12: All mechanical work shall be inspected and approved under a separate permit issued by the City of Tukwila
Permit Center (206/431-3670).
17: The attached set of building plans have been reviewed by the Fire Prevention Bureau and are acceptable
with the following concerns:
21: The Auto Fryer shall be installed per the manufacturers instructions.
16: Fire protection systems shall be maintained in accordance with the original installation standards for that
system. Required systems shall be extended, altered or augmented as necessary to maintain and continue
protection whenever the building is altered, remodeled or added to. Alterations to fire protection systems
shall be done in accordance with applicable standards. (IFC 901.4)(EXTEND SPRINKLER PROTECTION TO
BENEATH KIOSK CEILING.)
14: Sprinklers shall be installed under fixed obstructions over 4 feet (1.2 m) wide. (NFPA 13-8.6.5.3.3)
13: All new sprinkler systems and all modifications to existing sprinkler systems shall have fire department
review and approval of drawings prior to installation or modification. New sprinkler systems and all
modifications to sprinkler systems involving more than 50 heads shall have the written approval of Factory
Mutual or any fire protection engineer licensed by the State of Washington and approved by the Fire
Marshal prior to submittal to the Tukwila Fire Prevention Bureau. No sprinkler work shall commence
without approved drawings. (City Ordinance No. 2436).
23: Portable fire extinguishers shall be provided within a 30-foot (9144 mm) travel distance of commercial -type
cooking equipment. Cooking equipment involving vegetable or animal oils and fats shall be protected by a
Class K rated portable extinguisher. (IFC 904.11.5)
22: Portable fire extinguishers, not housed in cabinets, shall be installed on the hangers or brackets supplied.
Hangers or brackets shall be securely anchored to the mounting surface in accordance with the
manufacturer's installation instructions. Portable fire extinguishers having a gross weight not exceeding 40
pounds (18 kg) shall be installed so that its top is not more than 5 feet (1524 mm) above the floor. Hand-
held portable fire extinguishers having a gross weight exceeding 40 pounds (18 kg) shall be installed so that
its top is not more than 3.5 feet (1067 mm) above the floor. The clearance between the floor and the
bottom of the installed hand-held extinguishers shall not be less than 4 inches (102 mm). (IFC 906.7 and IFC
906.9)
18: Post correct address of K-1221 on kiosk per approved Westfield standards.
15: Contact The Tukwila Fire Prevention Bureau to witness all required inspections and tests. (City Ordinances
#2436 and #2437)
19: Any overlooked hazardous condition and/or violation of the adopted Fire or Building Codes does not imply
approval of such condition or violation.
20: These plans were reviewed by Inspector 511. If you have any questions, please call Tukwila Fire Prevention
Bureau at (206)575-4407.
PERMIT INSPECTIONS REQUIRED
Permit Inspection Line: (206) 438-9350
1700 BUILDING FINAL**
1400 FIRE FINAL
0409 FRAMING
0606 GLAZING
0502 LATH & GYPSUM
CITY OF TUKM, A
Community Development Department
Public Works Department
Permit Center
6300 Southcenter Blvd., Suite 100
Tukwila, WA 98188
http://www.TlikwilaWA.gov
Building Permit No. 1 t `lam 043
Project No.
Date Application Accepted:
Date Application Expires:
(For office use only)
CONSTRUCTION PERMIT APPLICATION
Applications and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or by fax.
**Please Print**
SITE LOCATION
Site Address:
2800 Southcenter Mall
Tenant Name: Potato Corner (Kiosk)
PROPERTY OWNER
Name: WESTFIELD SHOPPING CENTER
Address: 2800 Southcenter Mall
City: Tukwila State: WA Zip: 98188
CONTACT PERSON — person receiving all project
communication
Name: William Millhollin
Address: 1026 SW 151 st ST
City: Burien State: WA Zip: 98166
Phone: (206) 601-7043 Fax:
Email: william@nwpermit.com
GENERAL CONTRACTOR INFORMATION
Company Name: TBD
Address:
City: State: Zip:
Phone: Fax:
Contr Reg No.: Exp Date:
Tukwila Business License No.:
King Co Assessor's Tax No.: 9202470010
Suite Number: #9077 Floor:
New Tenant: ❑ Yes ❑..No
ARCHITECT OF RECORD
Company Name: Duncan Design. Group
Architect Name: Tyler Duncan
Address: 1350 Manufacturing ST #103
City: Dallas State: TX Zip: 75207
Phone: (214) 748-4400 Fax:
Email: tduncan@duncandesigngroup.com
ENGINEER OF RECORD
Company Name:
Engineer Name:
Address:
City:
State:
Zip:
Phone:
Fax:
Email:
LENDER/BOND ISSUED (required for projects $5,000 or
greater per RCW 19.27.095)
Name: r'r K J 04-ni
Address: 11Oit ppeati a
City: 1�`�6®j State:x'
Zip:!'g2/
H:\Applicatiom\Foam-Applications On Line\2011 Applications\Fertnit Application Revised - 8-9-11.docx
Revised: August 2011
bh
Page I of 4
BUILDING PERMIT INFORMATIO 206-431-3670
Valuation of Project (contractor's bid price): $ 7.01 LVO Existing Building Valuation: $
Describe the scope of work (please provide detailed information):
New tenant kiosk inside Southcenter Mall. New kiosk, framed ceiling, electrical and plumbing for food service equipment and
lighting.
Will there be new rack storage? ❑ Yes
0.. No If yes, a separate permit and plan submittal will be required.
Provide All Building Areas in Square Footage Below
Existing
Interior Remodel
Addition to
Existing
Structure
New
Type of
Construction per
IBC
Type of
Occupancy per
IBC
1' Floor
)-
o-tIr
J
2nd Floor
3`d Floor
Floors thru
Basement
Accessory Structure*
Attached Garage
Detached Garage
Attached Carport
Detached Carport
Covered Deck
Uncovered Deck
PLANNING DIVISION:
Single family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches)
*For an Accessory dwelling, provide the following:
Lot Area (sq ft): Floor area of principal dwelling: Floor area of accessory dwelling:
*Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence.
Number of Parking Stalls Provided: Standard: Compact: Handicap:
Will there be a change in use? ❑ Yes ❑ No If "yes", explain:
FIRE PROTECTION/HAZARDOUS MATERIALS:
O Sprinklers 0 Automatic Fire Alarm ❑ None ❑ Other (specify)
Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ Yes ❑ No
If "yes', attach list of materials and storage locations on a separate 8-1/2" x 11" paper including quantities and Material Safety Data Sheets.
SEPTIC SYSTEM
❑ On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health
Department.
H:\Applications\Forms-Applications On Line\2011 ApplicationsTermit Application Revised - 8-9-11.docx
Revised: August 2011
bh
Page 2 of 4
PUBLIC WORKS PERMIT INFC ATION — 206-433-0179
Scope of Work (please provide detailed information):
N/A
Call before you Dig: 811
Please refer to Public Works Bulletin #1 for fees and estimate sheet.
Water District
0 ...Tukwila ❑ ...Water District #125
❑ ...Water Availability Provided
Sewer District
0 ...Tukwila
❑ ...Sewer Use Certificate
O .. Highline
❑ ...Valley View ❑ .. Renton
❑...Sewer Availability Provided
❑ .. Renton
❑ .. Seattle
Septic System:
❑ On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health Department.
Submitted with Application (mark boxes which apply):
0 ...Civil Plans (Maximum Paper Size — 22" x 34")
❑ ...Technical Information Report (Storm Drainage) 0 .. Geotechnical Report 0 ...Traffic Impact Analysis
❑ ...Bond 0 .. Insurance ❑ .. Easement(s) 0 .. Maintenance Agreement(s) 0 ...Hold Harmless — (SAO)
❑ ...Hold Harmless — (ROW)
Proposed Activities (mark boxes that apply):
❑ ...Right-of-way Use - Nonprofit for less than 72 hours
❑ ...Right-of-way Use - No Disturbance
❑ ...Construction/Excavation/Fill - Right-of-way ❑
Non Right-of-way 0
❑ ...Total Cut cubic yards
❑ ...Total Fill cubic yards
❑ ...Sanitary Side Sewer
❑ ...Cap or Remove Utilities
0 ...Frontage Improvements
❑ ...Traffic Control
❑ ...Backflow Prevention - Fire Protection
Irrigation
Domestic Water
❑ .. Right-of-way Use - Profit for less than 72 hours
❑ .. Right-of-way Use — Potential Disturbance
❑ .. Work in Flood Zone
❑ .. Storm Drainage
❑ .. Abandon Septic Tank
❑ .. Curb Cut
❑ .. Pavement Cut
❑ .. Looped Fire Line
11
11
❑ .. Grease Interceptor
❑ .. Channelization
❑ .. Trench Excavation
❑ .. Utility Undergrounding
❑ ...Permanent Water Meter Size... 11 WO #
❑ ...Temporary Water Meter Size .. 1 9 WO #
❑ ...Water Only Meter Size WO # ❑...Deduct Water Meter Size
❑ ...Sewer Main Extension Public 0 Private ❑
❑ ...Water Main Extension Public ❑ Private 0
11
FINANCE INFORMATION
Fire Line Size at Property Line Number of Public Fire Hydrant(s)
0 ...Water 0 ...Sewer 0 ...Sewage Treatment
Monthly Service Billing to:
Name: Day Telephone:
Mailing Address:
City State Zip
Water Meter Refund/Billing:
Name:
Mailing Address:
Day Telephone:
City
State Zip
H:\Applications\Forms-Applications On Line\2011 Applcations\1'ermit Application Revised - 8.9-1 t.docx
Revised: August 2011
bh
Page 3 of 4
PERMIT APPLICATION NOTES -
Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject
to possible revision by the Permit Center to comply with current fee schedules.
Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation.
The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be
requested in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition).
I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER
PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT.
BUILDING OWNS R AUTHORIZED GENT:
Signature: Date: 08/12/2014
Print Name: William Millhollin Day Telephone: (206) 601-7043
Mailing Address: 1026 SW 151st ST Burien WA 98166
City State Zip
H:\Applications\Forms-Applications On Line\2011 ApplicationsWermit Application Revised - 8.9-1 I.docx
Revised: August 2011
bh
Page 4 of 4
Cash Register Receipt
City of Tukwila
DESCRIPTIONS
PermitTRAK
ACCOUNT I QUANTITY
PAID
$510.92
D14-0263 Address: 2800 SOUTHCENTER MALL UnitK1221 Apn: 9202470010 $510.92
DEVELOPMENT $486.80
PERMIT FEE
R000.322.100.00.00
0.00
$482.30
WASHINGTON STATE SURCHARGE
B640.237.114
0.00
$4.50
TECHNOLOGY FEE $24.12
TECHNOLOGY FEE
TOTAL FEES PAID BY RECEIPT: R3658
R000.322.900.04.00 0.00 $24.12
$510.92
Date Paid: Wednesday, November 26, 2014
Paid By: WESTMARK CONSTRUCTION, INC.
Pay Method: CHECK 70987
Printed: Wednesday, November 26, 2014 10:58 1 of 1
AM
rdPSYSTEMS
Cash Register Receipt
City of Tukwila
DESCRIPTIONS ACCOUNT QUANTITY
PermitTRAK
PAID
$404.73
D14-0263 Address: 2800 SOUTHCENTER MALL K1082 Apn: 9202470010
$313.50
DEVELOPMENT
$313.50
PLAN CHECK FEE R000.345.830.00.00
0.00
$313.50
EL14-0784 Address: 2800 SOUTHCENTER MALL K1082 Apn: 9202470010
$45.85
ELECTRICAL
$45.85
PLAN CHECK FEE I R000.345.832.00.00 I
0.00
I
$45.85
PG14-0135 Address: 2800 SOUTHCENTER MALL K1082 Apn: 9202470010
$45.38
PLUMBING
$45.38
PLAN CHECK FEE R000.322.103.00.00
TOTAL FEES PAID BY RECEIPT: R2846
0.00
$45.38
$404.73
Date Paid: Tuesday, August 12, 2014
Paid By: NORTHWEST PERMIT INC
Pay Method: CHECK 9557
Printed: Tuesday, August 12, 2014 4:03 PM 1 of 1
CRWSYSTEMS
1c
6300 Southcenter Blvd., #100, Tukwila. WA 98188
Permit Inspection Request Line (206) 438-9350
INSPECTION RECORD
Retain a copy with permit
PI V-62.43
PERMIT NO.
CITY OF TUKVVILA BUILDING DIVISION
(206) 431-3670
Forojecti ,
Pate4 t—O CO ((-('-rt
'Type jo97ectiort
_...y i
v --f „
Address:
.2it,°0 ctititt4 CfrA-Cr( (
,
Date Calle,
Special Instructions: . t
(krill' K iZ (
A...4A
Date W nted:
f
a.m.
Reque ter:
Phone No:
Approved per applicable codes. Corrections required prior to approval,
OMMENTS;
O1J‘F• Kcd
Inspector
Da
-2-3 -15-4
REINSPECT ON FEE REQUIRED. Prior to next inspection, fee must be
paid at 6300 Southcenter Blvd.. Suite 100, Call to schedule reinspection.
INSPECTION RECORD
Retain a copy with permit
INS TION NO, PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670
Permit Inspection Request Line (206) 438-9350
j)fit-o2-163
Prot j_ f...
ro I -pp (-e G-K e--fr
Type tirpottbon:
P-f t-tcf
Address. .5,044tslic Amzu
Date Called:/
Special Instructions:
oim
•
Date trted:
...... _
a.m.
O.rn•
'Requester:
Phone No:
LJApproved per applicable codes.
Corrections required prior to approval,
COMMENTS:
rrrt 141..Q r9rcv
,
0/tort 76?;t_q(
Inspector:
Date:
REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be
paid at 6300 Southcenter Blvd.. Suite WO. Call to schedule reinspection.
INSPECTION RECORD
Retain a copy with permit
— 0243
P/L(t92-6.
PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670
Permit Inspection Request Line (206) 438-9350
Project- 'Ty
po av--
oflospctign:
ow(y r<( p-cr /
Aiddiess:
1-C)C)s° CO tAll/L-qrs 'kW/
Date Caged:
Special Instructions: UltrIK/22-1
4,11
Date Wanted:
3- z-o - (s-
a.m.
PA.
Requester:
Phone No:
EjApproved per applicable codes.
Corrections required prior to approval.
COMMENTS: c
C'Wel 1 Ui11L- b pig,/ `-
Cb ircrrc Fc:frkiv( ce/yrarq/
-re0-fr-(-c_ci-( Q firrovez
) fc, pc.
cobitt,--4( r-r..*(1 (frCP Gtol-r
N/A-
CAW
Inspector:
'Date.3
T REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be
paid at 6300 Southcenter Blvd.. Suite 100. Catl to schedule reinspection.
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO, PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670
Permit Inspection Request Line (206) 438-9350
Project: —
\.-
‘ 0-1-A-C
Type ofifnspectioa: 1 f-
AclOresA_:
) Of/ 5C
AAA11
Date Called:
Special'Instructions:
...-----
Date Wanted:
1 70-
6.1.n.
15 P.m.
Requester:
, 4-,
\
Phone No:
2 -s , 537-
7 --
--
,7—'
(4) -> 7 ,o
12( Approved per applicable codes.
Corrections required prior to approval,
COMMENTS:
Instector:
LI
Date:
- -1/0 - 5
REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call to schedute reinspection
INSPECTION NO.
CITY OF TUKWILA BUILDING D
6300 Southcenter Blvd„ #100, Tukwila. WA 98188
Permit Inspection Request Line (206) 438-9350
INSPECTION RECORD A An /
Retain a copy with permiti."—u
PERMIT NO.eA
VISION
(206) 431-3670
-....,
ProjectnT(JoriJcve,
/Jo( -IO
Type of InspectiOn:
-
Adcfress;
s,_ Aif i4-1 I
Date Called:
Special Instructions: '
Date Wanted: /
i 3.-
/
e
p.m.
Requester:
'Phone No:
ElApproved per applicable codes.
EJCorrections required prior to approval.
COMMENTS:
.SuI3` e_cic 1-7) At( al? ear
er,or? �A,s OA R-DJm -Tit/
Ins`pector:
Date: / s—
REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be
paid at 6300 Southcenter Blvd.. Suite 100. Cali to schedule reinspection.
INSPECTION RECORD
Retain a copy with permit
INSPECTION NUMBER
PERMIT NUMBERS
CITY OF TUKWILA FIRE DEPARTMENT
206-575-4407
Project:
rMor-
Type of Inspection:
t tie
To
Address:
Suite #5C Mk-f I/
V 0 Z. t
Contact Person:
Special Instructions:
Phone No.:
Approved per applicable codes.
Corrections required prior to approval.
COMMENTS:
4I/
,')
2-2-0
5-/'
be- X/zZ l
- .,404-pf/"4
�jor
1
V
,
Needs Shift Inspection:
Sprinklers:
Fire Alarm:
Hood & Duct:
Monitor:
Pre -Fire:
Permits:
Occupancy Type:
1
Inspector:
s
Date: 0/z 3!
/ 5—
Hrs.:
/
0
$100.00 REINSPECTION FEE REQUIRED. You will receive an invoice from
the City of Tukwila Finance Department. Call to schedule a reinspection.
Billing Address
Attn:
Address:
Company Name:
City:
State:
Zip:
Word/Inspection Record Form.Doc
3/14/14
T.F.D. Form F.P. 113
INSPECTION RECORD
Retain a copy with permit
INSPECTION NUMBER
PERMIT NUMBERS
CITY OF TUKWILA FIRE DEPARTMENT
444 Andover Park East, Tukwila, Wa. 98188 206-575-4407
Project----
ra) f �'l 2 t�
Type of In pection: -1�°
f
�;= ;. _,_ .._ ;..-r_;;
Address:
Suite #: 2600 NA(7 lI ZZ/
l�
Contact erson:
Special Instructions:
Phone No.:
Approved per applicable codes.
Corrections required prior to approval.
COMMENTS:
nak ky.4.'" A of, /f V v/i7 0-7 —
— /f--,1-1 ,c,/ 6,/c, / 7 "i<
7-1e /737/ f 4 - 7 c ,
c e .
ii
�D%jJ,/jfjir
y(�
./J
�`
c4-i/ �+ 5
j 7'/- f�-�-''F / '' V f%i-!
,e ?‘ef' -76 lti/l .
., ,e o-,
— 1/V/5 /7
/-%�/ s-
7/.) ,4�7 .17.14
t s / iv //1(-
Needs Shift Inspection:
Sprinklers:
Fire Alarm:
Hood & Duct:
Monitor:
Pre -Fire:
Permits:
Occupancy Type:
Inspector:
i" 3 j
Hrs.:
/, c)
Date: eo.,/;
$100.00 REINSPECTION FEE REQUIRED. You will receive an invoice from
the City of Tukwila Finance Department. Call to schedule a reinspection.
Billing Address
Attn:
Address:
Company Name:
City:
State:
Zip:
Word/Inspection Record Form.Doc
6/11/10
T.F.D. Form F.P. 113
FILE COPY
Darn* No.
RESPONSE TO: CITY OF TUKWILA PERMIT CORRECTION LETTER #1
Potato Corner— 2800 Southcenter Mall, Space #9077, Tukwila, WA (K-1082)
Plumbing/Gas Piping PG14-0135
Development Application #: D14-0263
October 6, 2014
GREASE INTERCEPTOR MANUAL AND SPECIFICATIONS
AUTO FRYER MANUAL AND SPECIFICATIONS
REVIEWED FOR
CODE COMPLIANCE
APPROVED
OCT 2 3 2014
City of Tukwila
BUILDING DIVISION
RECEIVED
CITY OF TUKWILA
OCT 0 8 2014
PERMIT CENTER
CORRECTION ' 1 oz g,
�% 1
WWATTS®
WD Series
Tag:
PDI Certified Grease
Interceptor
SPECIFICATION: Watts Drainage WD Series PDI Certified recessed or floor mounted epoxy coated steel grease interceptor
with gasketed epoxy coated steel skid -proof cover secured with hex head center bolt(s), removable baffle assembly, deep
seal trap with cleanout, external cast iron flow control fitting, and no hub (standard) connections.
D (Length) x E (Width)
ISO
9002
1taT111.114,1M1
Inlet Imo' Outlet
Flow Restrictor
w/Vent Connection
L
B
Flow Rate (Select One)
Suffix Description
4 4 GPM
7 7 GPM
10 10GPM
15 15GPM
20 20 GPM
0
0
0
0
25 25 GPM ❑
35 35 GPM
50 50 GPM
G
❑
Options (Select One or More)
Suffix Description
-B Sediment Bucket ❑
•E Extension 0
-FC Flange 8, Clomp Device 0
-HD Heavy Duty (10,000 Ib.) 0
Traffic Cover
-O Inlet IS Outlet other than 0
Standard Size
.SS Stainless Steel 0
-THD Threaded Connections 0
-US Buy American Compliant 0
interceptor
Catalog
Number
Flow
Rate
GPM
Grease
Capacity
A
Inlet 8.
Outlet
B
Base to
Center
C
Top to
Center
D
Length
E
Width
F
Height
WD-4
WD-7
WD-10
WD-15
WD-20
WD-25
WD-35
WD-50
4
7
10
15
20
25
35
50
8
14
20
30
40
50
70
100
2"151)
2"(51)
2"(51)
2"(51)
3"(76)
3"(761
3"(76)
4"(102)
7-3/4"(197)
8.1 /2"(216)
8-1 /2"(216)
10-1/21267)
11-1 /2"(292)
12"(305)
14"(356)
16"(406)
3-1 /4"(83)
3-1 /2"(89)
3-1 /2"(89)
3-1 /2"(89)
3.1 /2"(89)
4-1/2"(114)
5"(127)
5-1 /21140)
16"(406)
18"(457)
21-3/4"(552)
22"(559)
2416101
26"(660)
30"(762)
32"(813)
10" (254)
13"(330)
14"(356)
15"(381)
15-3/4"(400)
16.1/21419)
18"(457)
22"(559)
11 "(279)
12"(305)
12"(305)
14"(356)
15"(381)
16-1/2"(419)
19"(483)
21-1/21546)
1
Job Nome Contractor
Job Location Controctor's P.O. No
Engineer Representotive
WATTS Drainage reserves the right to modify or change product design or construction without prior notice and without incurring any obligation to make similar changes and moddicatlons to products
previously or subsequently sold See your WATTS Drainage representative for ony clarification Dimensions are subject to manufacturing tolerances.
%WATTS®
Specification Drainage Products USA: 100 Watts Road, Spindale, NC, 28160-2298; TEL: 828-288-2179 TOLL -FREE: 1-800-338-2581 www.watts.com
ES-WD-WD SERIES USA 1304
WD SERIES
WINATTS®
INTERCEPTORS
TABLE OF CONTENTS
• Pictorial Index
• Product Recommendations
• Grease Interceptors
Design & Operation
Material & Characteristics
Sizing
Pipe Connection
Commonly Specified Options
Installation Considerations
Maintenance & Cleaning
Typical Installations
• Oil Interceptors
Design & Operation
Material & Characteristics
Sizing
Pipe Connection
Commonly Specified Options
Installation Considerations
Maintenance & Cleaning
Typical Installations
• Sediment Interceptors
Design & Operation
Material & Characteristics
Sizing
Pipe Connection
Installation Considerations
Maintenance & Cleaning
Typical Installations
S-WD-INTER-1 0812
WA'ITS®
INTERCEPTORS
WD SERIES
PDI Certified Grease
Interceptor
WD-L SERIES
PDI Certified Low Rough -In
Grease Interceptor
WD-A SERIES
Semi -Automatic
Greose Interceptor
WD-AH SERIES
Semi -Automatic Grease
Interceptor w/Housing
PICTORIAL INDEX
WD-LA SERIES
Semi -Automatic Low
Rough -In Grease Interceptor
GI-K SERIES
Large Capacity
Grease Interceptor
01 SERIES
Oil Interceptor
0I-K SERIES
Large Capacity
Oil Interceptor
SI-742
Sediment Interceptor
SI-740-L
Large capacity
Sediment Interceptor
SI-750
Hair Interceptor
SI-750-TO
Chrome Plated Top
Outlet Hair Interceptor
S1-762
Bottom Access Hair,
Plaster & Sediment Interceptor
LI SERIES
Lint Interceptor
Photo not
available at
this time
SA
Sediment Interceptor
S-WD-INTER-2 0812
%marls®
INTERCEPTORS
PRODUCT RECOMMENDATIONS
Application Product
Art Rooms, Dental Labs, Metal Recovery SI-742, SI-742-L, SI-762
Commercial Laundry, Washing Machines LI-800
Cooking, Prep Sinks, Dishwasher WD Series, GI-K Series
Elevator Pits & Oil Spill Areas OI Series, OI-K Series
Hair Wash Sinks SI-750, SI-750-TO
Pot, Pan, Scullery Sinks WD Series, GI-K Series
Sand & Sediment SA Series, See Also
FD-410 Catch Basin
Vehicle & Maintenance Areas OI Series, OI-K Series
GREASE INTERCEPTORS
Design & Operation
Watts Grease Interceptors are designed to remove grease and similar substances from waste water.
Interceptors prevent greasy substances from entering plumbing systems, septic fields, and waste water treat-
ment facilities, where they are difficult to process, and can create environmental problems. Commonly
specified in restaurant kitchens and food handling or processing areas, properly specified and maintained
interceptors keep drainage systems free of problematic grease accumulations.
Grease interceptors will separate all lighter -than -water substances, collecting them inside the interceptor,
above the static water line. Design criteria is determined by plumbing code, typically following guidelines
set forth by The Plumbing & Drainage Institute (PDI), which tests and rates interceptors. The accepted
industry and PDI Standard (PDI-G101) is for interceptors to maintain 90% separation efficiency, up to
the rated grease retention capacity (in Ibs.). The interception process is accomplished using the principle
of attraction of like substances. A flow restrictor on the inlet side slows incoming effluent, re -directing it
through baffling inside the interceptor. Slowing and baffling processes allow lighter -than -water substances
(grease) to accumulate above the static water line. The remaining water, free of grease, is forced through
the trap leg on the outlet side of the interceptor, and into the waste water drainage system.
Material & Characteristics
Epoxy Coated Steel - Interceptor body standard 11 ga. CR steel, with oven cured, acid resistant baked
gray epoxy coating, inside and out. Lid is epoxy coated 1/4" skid -proof checker plate steel, gasketted,
and secured with Allen head center bolt(s). All stainless steel construction may be specified for high
sanitary applications.
Flow Restrictor - WD Series Interceptors are supplied with an external cast iron flow restrictor. All other inter-
ceptor models are designed with a built-in stainless steel flow restrictor plate, located just inside the inlet.
S-WO-INTER-3 0812
INTERCEPTORS
GREASE INTERCEPTORS
;Sizing
Grease interceptors are sized according to the rate of incoming flow, in gallons per minute (GPM).
Associated with the incoming flow rate is an interceptor's capacity. The rated capacity, in lbs., is listed at
twice the flow rate, in GPM. For example, a 10 GPM interceptor has a rated capacity of 20 lbs.
General Procedure:
To Determine the Flow Rote of Each Sink:
1. Calculate the capacity of the sink in cubic inches:
(LENGTH) x (WIDTH) x (DEPTH) = CU.IN.
2. Convert the capacity from cub inches to gallons per minute (GPM): CU.IN. + 231 = GPM.
3. Adjust for displacement: GPM x 0.75 = GPM.
4. Result is the flow rate required to drain the sink in one minute.'
"Note: if drain down time is not calico!, an interceptor with a lesser flow rote, up to half the cokutoted flow
rote may be specified.
Example:
Three compartment pot sink, each compartment 12' x 12" x 15"
1. 12" x 12" x 15" = 2160 cu. in. x 3 comp. .= 6480 cu. in.
2. 6480 cu. in. _ 231 - 28 GPM.
3. 28 GPM x 0.75 = 21 GPM.
A 20 GPM interceptor would permit the sink to drain in slightly more than one minute.
'Discharge from spray hoods is determined by the Now rate of the hood.
'It is not recommended to pass. commercial dishwashers through on interceptor.
Sizing For Multiple Fixtures:
1. Determine the flow rate for each fixture io be serviced by the interceptor.
2. Add together 100% of the lorgest flow rate, 50% of the second largest, and 25% of all others.
3. Result is the recommended flow rote of the interceptor.
Example:
1, Fixture A: 35 GPM Flow Rate
Fixture B: 26 GPM Flow Rate
Fixture C: 18 GPM Flow Rote
Fixture D: 12 GPM Flow Rote
2. 35 GPM (A) x 100% = 35 GPM
26 GPM (8) x 50% = 13 GPM
30 GPM (C + D) x 25% = 7.5 GPM
Total Flow Rate = 55.5 GPM
A 50 GPM interceptor is recommended for this installation.
Typical Configurations
r
AIR NTAKE
VENTED WASTE
FLOW CONTROLLER
ON FLOOR
S-WD-INTER-4 0812
AO s i eta -rya -.a S
AIR INTAKE AIR INTAKE y
VENTED WASTE SINK i� VENTED WASTED
FLOW CONTROLLER TEE
RECESSED
FLOW CONTROLLER TEE
RECESSED WITH EXTENSION
WWA1TS®
INTERCEPTORS
GREASE INTERCEPTORS
Pipe Connecllion
No Hub (Standard) - Butt connection using no hub or neoprene coupling, suitable for cast iron, plastic,
and most other piping applications.
Threaded (T) - Female IPS threaded connections.
Commonly Specified Options
Sediment Bucket (-B) - Epoxy coated steel, located inside interceptor on inlet side. Collects large food or
other particles. To the extent possible, sediment should be strained or collected at the fixture, prior to the
grease interceptor. Sediment entering the waste line is likely to clog the interceptor's flow restrictor, slow-
ing drainage, and causing back-up difficulties.
Extension (-E) - Increases invert dimension to accommodate below grade piping.
Heavy Duty Traffic Cover (-HD) - Rated 10,000 Ibs. maximum safe live load.
Flange & Clamp Device (-FC) - Secures floor membrane or liner, generally specified for above grade
installations.
Flow through an interceptor is regulated by the flow restrictor. Increasing connection sizes has no benefi-
cial effect on flow, and larger piping can normally be accommodated with reducing bushings or couplings.
Installation Considerations
a.) Interceptors should be located as near as possible to the fixture(s) being served. Long piping runs
between a fixture and the interceptor will accumulate grease, causing drainage and clogging problems.
b.) Watts Drainage Grease Interceptors may be either floor mounted, under or beside the sink, or
recessed, to allow passage of foot traffic, or connect to floor drain discharge.
c.) Interceptors may be installed outside, but all piping must be below the frost line (see Extensions).
d.) WD Series Interceptors are supplied with an external flow restrictor, which mustbe installed between
the last fixture serviced, and the inlet of the interceptor.
e.) Venting is recommended on both the inlet and outlet side of the interceptor, or as governed by
local code. Units supplied with external flow restrictors are vented on the inlet side, from the top of the
restrictor tee.
Maintenance & Cleaning
Manual operation grease interceptors are cleaned by opening the cover, and removing grease accumulated
at the top of the interceptor. Accumulated grease may be removed manually, or pumped out, generally by
an outside service. Cleaning frequency is dependent upon the interceptor's capacity, and the amount of
incoming grease. The amount of accumulated grease must be kept below the rated capacity to maintain
separation efficiency.
S-WD-INTERS 0812
WWA'IIS®
INTERCEPTORS
TYPICAL GREASE INTERCEPTOR INSTALLATIONS
AIR INTAKE
VENT
FLOW CONTROL TEE
WD Series
AIR INTAKE
FLOW
CONTROL
TEE
c
WASTE —f
OUTSIDE WALL
VENT N
v
BOLT -ON
EXTENSION
WD-E Series
rAIR INTAKE
FLOW CONTROL TEE
WASTEf�
VENT
/ DRAW -OFF HOSE
SHUTOFF VALVE J
WASTE
WD-AFC Series
S-WD-INTER•6 0812
WWATTS®
INTERCEPTORS
OIL INTERCEPTORS
Design & Operation
Watts Drainage Oil Interceptors are designed to separate oily waste from interior drainage systems, or exte-
rior run-off areas. Commonly specified in service stations and other vehicle maintenance or parking areas,
oil interceptors prevent environmentally damaging and potentially dangerous oily substances from entering
septic fields, run-off areas, and waste water treatment facilities.
Similar to grease interceptors in operation, oil interceptors accumulate lighter -than -water oily waste above
the static water line inside the interceptor. Oil is automatically drained from the interceptor through a
draw -off valve, and directed to an approved holding tank (by others), for storage and eventual removal.
Material & Characteristics
Epoxy Coated Steel - Interceptor body standard 11 ga. CR steel, with oven cured, acid resistant baked
gray epoxy coating, inside and out. Lid is epoxy coated 1/4" skid -proof checker plate steel, gasketted, and
secured with Allen head center bolt(s). All stainless steel construction may be specified for non-standard
applications.
Flow Restrictor - Oil interceptors are supplied with a built-in stainless steel flow restrictor plate, just inside
the inlet.
Sizing
Oil Interceptors are sized according to the rate of incoming flow, in gallons per minute (GPM).
For indoor applications, flow rate can be calculated by adding the maximum discharge rates of all poten-
tial water sources. For example, a standard 3/4" hose connection will discharge approx. 10 GPM. A service
garage with three hose connections would have a maximum potential flow rate of 10 GPM x 3, or 30
GPM.
For outdoor applications involving rainwater run-off, flow rate should be derived from local rainfall tables,
and the slope characteristics of the area to be drained.
Pipe Connection
No Hub (Standard) - Butt connection using no hub or neoprene coupling, suitable for cast iron, plastic,
and most other piping applications.
Threaded (T) - Female IPS threaded connections.
S•WD•INTER•7 0812
WWATrS®
INTERCEPTORS
OIL INTERCEPTORS
Commonly Specified Options
Sediment Bucket (-B) - Epoxy coated steel, located inside interceptor on inlet side. Collects sediment or
other particles. To the extent possible, sediment should be collected with a catch basin (see Watts FD-
410), prior to the oil interceptor. Sediment entering the interceptor may clog the flow restrictor, slowing
drainage, and causing back-up difficulties.
Extension (-E) - Increases invert dimension to accommodate below grade piping.
Heavy Duty Traffic Cover (-HD) - Rated 10,000 lbs. maximum safe live load.
Flange & Clamp Device (-FC) - Secures floor membrane or liner, generally specified for above grade instal-
lations.
Inlet & Outlet Other Than Standard Size (-0) - Flow through an interceptor is regulated by the flow
restrictor. Increasing connection sizes has no beneficial effect on flow, and larger piping can normally be
accommodated with reducing bushings or couplings.
installation Considerations
a.) Watts Drainage Oil Interceptors are commonly recessed, to connect to floor drain discharge, and allow
passage of foot traffic.
b.) Provisions must be made to connect the oil interceptor draw -off to an approved underground oil stor-
age tank (by others). Where conditions permit, a manual draw -off valve (by others) may be installed. A
manual valve is generally accessed inside a pit, which houses the oil interceptor.
c.) Interceptors may be installed outside, but all piping must be below the frost line (see Extensions).
d.) Vent lines should be attached to dual no hub vent connections on the side of the interceptor. The lines
must be terminated outside the building, 12" apart in elevation, to allow circulation, and vent heavier-
than-air fumes that may accumulate inside the interceptor. The inlet side piping should also be vented
through the roof, or as governed by local code.
Maintenance & Cleaning
Oil interceptors are not designed to store oil. Oil should be drained into an approved storage tank, which
should be pumped as required. If a manual valve is used, oil should be drawn off on a regular basis,
dependent upon the amount of incoming effluent. The interceptor lid should be removed periodically, and
a visual inspection made, for sludge or other accumulations.
r VENT STACKS EXTENDS
n r THROUGH ROOF
i
II
TYPICAL FLOOR DRAINS
OIL INTERCEPTOR ii
GRAVITY DRAWOFF
o
i;
TO SEWER ! i j SERVICING CONNECTION
I ;;[ TO GRADE
I
I i i 1 OIL TANK
I / (BY OTHER31STORAGE
S-WD.INTER•8 0812
INTERCEPTORS
TYPICAL OIL INTERCEPTOR INSTALLATIONS
FLOOR DRAIN
VENT (TO OUTSIDE)
4.1
44
DRAW -OFF CONNECTION
WITH VALVE [BY OTHERS)
01 Series
VENT CONNECTION
THROUGH ROOF
TRENCH DRAIN
TO SEWER
GROUND LEVEL
ACCESS
•
0I-E Series
- TO SEWER
- UNDERGROUND
• OIL STORAGE
TANK (BY OTHEP,S)
M
CONCRETE SLAB
S•WD-INTER-9 0812
WWATrS®
INTERCEPTORS
SEDIMENT INTERCEPTORS
Design & Operation
Watts Sediment Interceptors are designed to separate heavier -than -water sediments or floating debris, such
as hair or lint, from plumbing waste systems. Sediment interceptors trap debris with a combination of
screening, and gravity separation for heavier -than -water sediments. Debris is accumulated inside the inter-
ceptor, where it is stored until removal.
Material & Characteristics
Epoxy Coated Cast Iron - Industrial grade cast iron, finished with Watts standard gray acid resistant epoxy
coating.
Epoxy Coated Steel - Standard 11 ga. CR steel, with oven cured, acid resistant baked gray epoxy coating.
Stainless Steel - 14 gauge, in accordance with ASTM A-351-Grade CF8 (type 304) Standard Specification.
Highly durable and resistant to corrosion.
Sizing
Sediment interceptors are sized according to rate of flow, or anticipated amount of debris. See specifica-
tion pages for specific flow rates and sizing.
Pipe Connection
No Hub (Standard) - Butt connection using no hub or neoprene coupling, suitable for cast iron, plastic,
and most other piping applications.
Threaded (T) - Female IPS threaded connections.
Installation Considerations
a.) Sediment interceptors should be located as near as possible to the source of the debris. Long piping
runs prior to the interceptor will accumulate debris, causing drainage and clogging problems.
b.) Small capacity sediment interceptors are generally mounted under or beside the sink. Larger capacity
interceptors may be floor mounted, or recessed, to allow the passage of foot traffic, or connect to floor
drain or other discharge lines.
c.) Interceptors may be installed outside, but all piping must be below the frost line (see Extensions).
d.) Venting of sediment interceptors is generally not required, however installers should reference local
codes prior to installation.
Maintenance & Cleaning
Sediment interceptors must be routinely inspected and cleaned, in order to prevent clogging, and maintain
operating efficiency. Maintenance frequency is primarily dependent upon the specific application, and
amount of incoming debris.
S-WD-INTER•10 08' 2
INTERCEPTORS
TYPICAL SEDIMENT INTERCEPTOR INSTALLATIONS
/////�///
u-800
RASEMENT FLOOR
COMMERCIAL WASHERS
FIRST FLOOR
11-800
10 SEWER
r •
.a
4
•
•
S-WD-INTER-1 1 0812
/ 40C-3
Data Sheet
'oo ;z. Gvo MernIts. No Pro m!
1) Place food in entry chute(s)
2) Select fry time on keypad(s)
or select programmable
presets
3) Food is fried to
perfection and
pt, automatically
'M, delivered to exterior
receiving tray(s)
Countertop deep fryer with a compact dual basket capable of producing up to
6 pounds of product per fry -cycle. Offers flexibility to operate each side independently.
Why AutoFry Delivers
Highly Reliable — With only three moving parts and 20 years of proven dependability, the AutoFry
is field tested.
Immediately Profitable — AutoFry is extremely economical to operate since no vents or hoods are
required (versus a minimum expenditure of $30,000-$50,000 to outfit a traditional professional kitchen
with vents, hoods and related HVAC).
Sophisticated — MTI's proprietary Simplifryt" technology offers 18 programmable presets, standby mode,
heat/time compensation intelligence and multiple language options.
Extremely Safe — ANSUL® fire suppression technology is built into all models. In addition, the fully
enclosed and automated process eliminates any employee exposure to hot oil.
Industry Leadership — MTI invented AutoFry over two decades ago and now represents the gold standard
in ventless deep-frying technology.
Proven Track Record — AutoFry clients include the industry leaders within the
pizza operator, bar/tavern, convenience store and movie theatre markets worldwide.
With distribution in 67 countries, AutoFry has you covered.
Your Source for Innovative Kitchen Solutions
Proudlyniadein th• U.S.A.
AutoFry® MTI-40C:/40C-3 SPECIFICATIONS
Double Basket
Double Oil Vat
Air Filtration System
ANSUL4
FIRE SUPPRESSION
SYSTEM
8 kw Heater
per Vat
FRONT VIEW
36"
91.44cm
Dual Food
Entry Chutes
SIDE VIEW
25"---�--�
63.5cm
ELECTRICAL
MTI-40C
0
0 p
MTI-40C-3
0 0
=
208-240 V / Single Phase
9.6 kW Total / 40 AMP @ 240 V
50 AMP (Dedicated Service Required)
6' (1.83m) Power Cord w/NEMA Plug / 6-50 Plug
208-240 V / 3 Phase
12 kW Total / 28.9 AMP
14.4 kW Total / 34.64 AMP
16.4 kW Total/ 39.45 AMP
50 AMP (Dedicated Service Required)
6' (1.83m) Power Cord w/NEMA Plug / 15-50 Plug
CAPACITY
Oil
2.75 gallons (10.41 liters) per side, 5.5 gallons (20.82 liters) total
Cooking
50-100 lbs. (22.68-45.36kg) French Fries per hour, frozen to done.
Capacity will vary depending on french fry type.
MACHINE
Dimensions
25"D x 36"W x 32.5"H (63.5crn Deep x 91.44cm Wide x 82.55cm High)
Clearances
0" = Sides O" = Back 24" = Top (Ocm = Sides Ocm = Back 61cm = Top)
Construction
16 Gauge Stainless Steel
Shipping Dims.
32" x 40" x 36" (81.28cm x 1.016m x 91.44cm)
Shipping Weight
310 lbs. (140.61kg)
LISTED
,s 0 CE
Motion Technology, Inc., 10 Forbes Road, Northborough, MA 01532
(508) 460-9800 • FAX (508) 393-5718
We reserve the right to change specifications appearing upon this brochure without notice
and without incurring any obligation for the equipment previously or subsequently sold. Patent pending.
32.5"
82.55cm
Gan
Page 1 of 1
VENTLESS LECTRIC FRYER MODEL .MTI-40C
Dowse BOOM
()cubic Oil W
Electrical
Oil Capacity
Cooking Capacity
Clearances
Machine Dimensions
Construction
Shipping Weight
Shipping Dimensions
Options
Warranty
3g-
Air FXtrtr an Syvynf
ANSUU'
Fire Syslem
kw Hazel
per Ne.
25,
SPEC i t 1 G A T t O N S
Dual f x d Entry Chutes
32.5'
208f240 V 9.6kVil Total
40 AMP 240 V / Single Phase`
50 AMP (Dedicated SantSante Required,
6'Cord w/NEMA6.5OPlug
2.50 Gallons per side (5 gallons total)
SO -100 Lbs. French Frles/Hour (Frozen to Done) °weal to easy de(r?fyiing on fon:ft Fry type.
Sides = 0" Back = 2" Top = 24"
25"Ox36"Wx32.5"H
16 Gauge Stainless Steel
310Lbs.
32"ox40"Wx36"H
43 phase available triton request. Dual MTl L'luminate beat lamps: 110 ACV 4.6 AMPS
1 Year Paris+Labor; 3 Years Electronic Controls, 5 Years Frypot / Chassis
http://mtiproducts.com//wp-content/uploads/20I 2/01 /mti40cspecs.gif 5/25/2013
FILE COPY
RESPONSE TO: CITY OF TUKWILA PERMIT CORRECTION LETTER #1
Potato Corner — 2800 Southcenter Mall, Space #9077, Tukwila, WA (K-1082)
Plumbing/Gas Piping PG14-0135
Development Application #: D14-0263
October 6, 2014
FIRE RATING DATA SHEETS FROM MANUFACTURER'S
REVIEWED FOR
CODE COMPLIANCE
APPROVED
OCT 2 3 2014
City of Tukwila
BUILDING DIVISION
RECEIVED
CITY OF TUKWILA
OCT 0 8 2014
PERMIT CENTER
CORRECTION p
Marilte
simply amazing
www.marlite.com Technical Data
2008
Marlite FRP -- Pebbled Texture & Smooth Class "III/C"
Wall Panel
Product
Marlite Fiberglass Reinforced Plastic (FRP) Wall Panels, available in textured and smooth surfaces, provide
ultimate durability, satisfying the most stringent demands. Marlite FRP is tough, water-resistant, economical to
install and easy to maintain.
Features & Attributes
• Tough surface resists stains, chemicals, scratches and abrasions and possesses high impact strength.
• Moisture resistant surface makes the panel ideal for wet environments and does not support the growth of
mold or mildew.
• Panels are quick and easy to install and can be simply sprayed and wiped clean.
Applications & Uses
Marlite FRP is ideal for use in kitchens, restrooms, laundries, laboratories and many other service areas in
restaurants, supermarkets, convenience stores, hotels and motels, heath care facilities, day care centers, food
processing plants, correctional facilities, refrigerated warehouses, car washes and agricultural facilities.
Product Identification
FRP Panels
Flame Spread <200
Smoke Developed <450
Standard Items
Available Harmonizing
Sizes Molding
Suggested
Adhesive /
Sealant
Packaging & Weight
FRP P100 White
FRP P106 Beige*
FRP P118 Natural Almond
FRP P140 Ivory
FRP P145 Silver
FRP P151 Light Grey
FRP P199 Bright White
4' x 8'
4' x 9'
4' x 10'
.090"
nominal
panel
thickness
P100
P106
P118
P140
P145
P151
P100
C375 or C551 /
MS250 or
MS251
32sgft/20#per pc
36 sq ft / 23# per pc
40 sq ft / 25# per pc
`available in 4' x 10' only.
Smooth FRP
Panels
Flame Spread <200
Smoke Developed <450
Standard Items
Available Harmonizing
Sizes Molding
Suggested
Adhesive /
Sealant
Packaging & Weight
FRP S100G White
FRP S118G Almond
FRP S100 S/2/S White"
4' x 8'
4' x 10'
.090"
nominal
panel
thickness
PVC P100
PVC P118
PVC P100
C375 or
C551/MS250 or
MS251
4' x 8'
32 sq ft / 20# per pc
4' x 10'
40 sq ft / 25# per pc
Physical Properties
Property
ASTM
Procedure
Typical Value
Marlite FRP
Flexural Strengths (psi)
D790
1.7 x 10 °
Flexural Modulus (psi)
D790
6.0 x 10 5
Tensile Strengths (psi)
D638
8.0 x 10 3
Tensile Modulus (psi)
D638
9.43 x 10 3
Barcol Hardness
D2583
40
lzod Impact Strengths (n#iin)
D256
7.0
Thermal Coeffiecient Of
Lineal Expansion (fnbnIF )
D696
1.6 x 10 .5
Water Aborption (%)
D570
.17
Specific Gravity
D792
1.53
Fire Ratings
E-84
Class Ili/C
Flame Spread
<200
Smoke Generation
<450
CAN/ULC Fire Ratings
S102-M88
Flame Spread
90
Smoke Generation
190
Panel Specifications
1. Marlite FRP Panels are manufactured using a homogenous
mixture of calcium carbonate, fiberglass and resin.
2. Panels shall have a pebble texture or smooth texture front
side. Panel color shall be per specification. Panel backside is
smooth and may possess slight imperfections that do not
adversely affect performance or physical properties and are not
cause for rejection.
3. Panel quality standards are:
Panel thickness: .090" +/- 10%
Width: 48" +/- 1/8"
Length: specified length +/- 1/8"
Squareness: not to exceed 1/8" for 8' panels or 5/32" for 10'
panels
4. Panels shall be installed in strict accordance with Marlite FRP
Installation Instructions.
Approvals & Certifications
• Class III/C Fire Ratings per ASTM E-84 flame spread
and smoke development tests
• Meets USDA/FSIS requirements
• Canadian Food Inspection Agency and Agriculture
Canada approved
• ICC Report #ER-5489
• Mold & Mildew Resistant per ASTM D3273-94 and
D3274-95 tests
• Factory Mutual tested and listed
Storage & Preparation
Carefully inspect all panels prior to installation. Notify Marlite at
once if panels are deemed unacceptable. Marlite FRP Panels
should be stored indoors on a flat, clean, dry surface for at least
24 hours prior to installation. Room and material (panels and
adhesive) temperature should both be at or near 70.F at the
time of installation. Martite FRP is intended to be installed over
unfinished, untreated plywood or unfinished, untreated drywall.
Contact Marlite prior to installing over other substrates.
Installation Overview
Safety —.use eye protection. Wear filter mask to cover nose
and mouth, especially when cutting panels.
Tools Required — power saw (carbide tip), saber saw
(metal cutting blade), caulking gun, tape measurer, drill, file,
hammer, level, saw horses and supports.
See Marlite FRP Installation Instructions for complete details.
Accessories
• Marlite PVC Trim Molding with integral, matching
colors, 8' & 10' lengths.
Martite Stainless Steel and PVC Outside Corner
Guards, 8' & 10' lengths.
Marlite PVC Base Molding, 10' lengths.
C-551 Marlite FRP Adhesive or C-375 Marlite
Construction Adhesive
MS-250 Clear & MS-251 White Marlite Silicone
Sealant
Serviceable Temperature Range
Martite FRP Panels shall maintain its performance
characteristics and physical properties in temperatures ranging
from -40^F to 130-F. Marlite FRP may discolor near heat
sources — such as ovens, fryers, heat lamps and toasters —
where temperatures exceed 130.F.
Marlite Pebbled Texture Advantage
Martite FRP Panels feature a unique pebble texture that offers
cleaning advantages over the cracked ice texture used in other
manufacturers' FRP panels. These advantages are attributed to
the less dramatic peaks and valleys of the Martite FRP texture.
(Per NEMA LD3-1991 Stain Test)
Cleaning Guidelines
When a regular cleaning schedule is executed, soil and dirt will
not build up. A mild, non-abrasive cleaner is effective.
For Additional Information, see:
www.marlite.com
Marlite FRP Panels Color Brochure
Marlite FRP CSI Specifications
Marlite FRP Installation Instructions
Marlite FRP Cleaning Instructions
Marlite
simply amazing
202 Harger St. PO Box 250
Dover, OH 44622
800.377.1221
330.343.7296 fax
www.mariite.com
Form FR20-04081
FORMICA® LAMINATE BY FORMICA GROUP
TECHNICAL DATA (GENERAL PUPOSE GRADE 10 AND POST -FORMING GRADES 12 & 20)
PRODUCT DESCRIPTION
Melamine -impregnated decorative surface papers are combined
with phenolic -treated kraft paper and consolidated in a press al
high pressures. The sheet back is sanded to maintain a uniform
thickness and facilitate bonding.
COLORS AND FINISH
Formica• Brand Laminate sheets (horizontal generai purpose
grade 10/HGS) are available in a broad selection of designs and
colors. Standard finishes for each pattern are detailed in the
Formica Corporation - National Product Guide (Form No. 02-034W).
Not all finishes are available in all Solid Colors / Patterns Wood
grains. Polished finish (-90) is not recommended for heavy-duty
horizontal surfaces.
Formica Brand Laminate sheets (horizontal post -forming grade
12/HGP and vertical post -forming grade 20/VGP) are available
in a broad selection of designs and colors. Standard finishes for
each pattern are detailed in the Formica Corporation - National
Product Guide (Form No. 02-034W). Not all finishes are available
in all Solid Colors / Patterns / Woodgrains. Polished finish (-90) is
not recommended for heavy -duly horizontal surfaces.
RECOMMENDED APPLICATION
Grade 10/HOS
Formica Brand Laminate - general purpose grade 10/HGS
is intended tor application to interior horizontal or vertical sur-
faces where design, appearance. quality. cfurability,,resistance to
stain, and resistance to heal from ordinary sources are
important considerations.
Grade 12/HGP
Formica Brand Laminate - post -forming laminate grade 12/HGP
is intended for application 10 interior horizontal or vertical sur-
faces requiring 1/2° (12.7mm) or greater outside radiused edges,
and/or 3/16" (4.8mm) cove radii, where design, appearance,
quality.
durability. resistance to stain, and resistance to heat Irom ordi-
nary sources are important considerations.
Grade 20/VGP
Formica Brand Laminate - post -forming grade 20/VGP is
intended for application to interior vertical surfaces requiring
318" (9.5mm) or greater outside radiused edges. where design.
appearance, quality. durability. resistance to slain, and resisiance
to heat from ordinary sources are important consideratioiis.
FABRICATION AND ASSEMBLY
LIMITATIONS
Formica Brand Laminate is designed for interior use only. Do not
adhere directly to plaster, drywall (gypscnn hoard), or concrete.
Do not use in areas exposed 10 temperatures exceeding 275°F
(135°C) or for exterior applications. When using Grade 20. finished
panel widths should not exceed 24" (610mm) maximum,
unless the adhesive system is a rigid set adhesive like PVA (wood
glue). We do not recommend contact adhesive for Grade 20 panels
wider than 24" (610num). When using Grade 20-90 gloss finish on
a panel application, there will be a degree of telegraphing on the
surface. Formica recoinmends using Grade 10-90 or 12-90 gloss
for these applications.
MACHINING LOW SHEEN LAMINATE SHEETS
Formica Brand Laminate with low sheen surfaces are subject
to marring. Fabricating with peel coat on surface (if applicable)
is recommended. Router base should be clean and tree of burrs
and debris. Table saws should he clean, flat. and Tree o1 burrs.
STORAGE
Formica Brand Laminate should he stored horizontally, with a
caul board or other protective sheet placed on lop to protect the
material from possible damage. The material should be protected
from moisture, and should never be stored in contact with the
floor or an outside wall. Optimum conditions for storage are
approximately 75°F (24"C), and 45% to 55% relative humidity.
PRECONDITIONING
Prior to fabrication. allow laminate sheet and substrate to
acclimate for al least 48 hours at the same ambient conditions.
Optinunn conditions are approximately 75°F (24`C), and relative
humidity of 45°0 to 55%. Provisions should be made for the
circulation of air around the materials.
SUBSTRATES
Formica Brand Laminate sheet should be bonded to an
appropriate substratesuch as 445 density particleboard (ANSI
A208.1 - 1090). or Medium Density Fiberboard (MDF). Due to the
potential for stress cracking, shrink back, and surface telegraphing
problem:. the use of plywood is stroncly discouraged and not
recommended. The substrate should be sanded smooth, and
should be clean, -free of oil or grease, and uniform in thickness.
Formica Brand Laminate sheet (grade 101HGS) can be bonded
to metal substrates using contact adhesive (see recommendations
below, under Adhesives). Refer to For mica Laminate Brief
Veneered to Meta( Substrates for General Intorrr;atron, Materials.
Conditions and Methods Forrnk a Corporation does not warranty
this particular application.
FORMICA®LAMINATE BY FORMICA GROUP
TECHNICAL DATA (GENERAL PUPOSE GRADE 10 AND POST -FORMING GRADES 12 & 20) coNTINIJED
ADHESIVES
Contact. semi -rigid (PVAc), or rigid (urea. resorcinol) adhesives
may be used. Follow the adhesive manufacturer's recommenda-
tions. Certain combinations of finish, substrate, and adhesive can
cause telegraphing.
When bonding Formica Brand Laminate sheet (grade 10/ HGS)
to metal substrates using contact adhesive, use Formica brand
(laminable solvent -based 0155 oi non-flammable solvent -based
11120M contact adhesives. Do not use water -based Ot SBR types
of contact adhesive when bonding laminate sheets to
metal substrates.
ASSEMBLY
Material, equipment, and workmanship should conform to the
Formica Corporation recommended standard practices, condi,
lions. procedures, and recommendations as specified by ANSI/
NEMA LD3-2005, Architectural Woodwork Duality Standards
and ANSI 161.2-1998 Standards.
Formica Brand Laminate sheets (grade 10, 12, and 20) can be
sawed, drilled, routed, and fabricated using standard carbidetipped
cutting tools.
Holes tor screws or bolts should be drilled oversized.
Panel assemblies should be laminated with the appropriate
backing sheet to minimize warpage. Formica backing sheets
(grade, 91/BKV or 92/BKH) are recommended for less critical
aOblications. Optimum balancing is obtained by bonding the
same surface laminate on both sides of the assembly with the
same adhesive. Always align sanding marks in the same direction.
All inside corners of cutouts must be radiused as laro,c,, as possible.
1/8" (3.18mm) minimum. to avoid stress cracking. The edges and
corners should he routed, sanded, or riled smooth and free of
chips or nicks. Panels fabricated using metal substrates, which
are more dimensionally stable than wood -based materials. should
he installed in a framing system, which captures the perimeter
of thE., panel yet allows 0 the normal dirnensional movement 01
tho laminate. This is to protect the panel edge and prevent edge
lifting or separation from the substrate, which can occur under
dry conditions.
TECHNICAL DATA
Performance compliance of Formica Brand Laminate General
purpose grade 10 and Post -forming grades 12 and 20
ANSI / NEMA STANDARDS PUBLICATION — L03-2005
PHYSICAL PROPERTIES
Appearance
Light Resistance
LD3 TEST 10/HGS
3.1 No ABC Delec is
3.3 Slghl
Cleanability
3.4 20 (max/
Stain Resistance
Reagents I - 10
Reagents 11 - 15
3.4
No Effect
Moderate
Boiling Water Resistance
3.5
Nc Effect
High Temperature Resistance
3.6
Sight
Ball Impact Resistance - irr
- MT
3.8
50 (min
1270 (inn)
Radiant Heal Resistance- sec
3.10 t 25
Dimensional Change 3.11
Machine Direction - % 0.50 (mix.)
Cross Direction - % 0.90 (max.)
Wear Resistance - cycles 3.13 400 (min )
PHYSICAL PROPERTIES
Appearance
LD3 TEST 12/HGP
20/VOP
3.1 No ABC No i.`-.BC
Defects Diets
Light Resistance
3.3 Saght Slight
Cleanability 3.4 20 imax.) 20 (max.)
Stain Resistance 3.4
Reagents 1 - 10
Reagents 11 - 15
No Effect No Effect
Moderate Moderate
Soiling Water Resistance
3.5
Slight
Slight
High Temperature Resistance 3.6
Ball Impact Resistance - in 3.8
- MM
Sighi Slight
30 (min) 20 (rnn)
762 (min ) 508
Radiant Heat Resistance - sec
3.10 100 (min ) 80 (mai 1
Dimensionai Change
Machine Direction - %
Cross Direction - % 1.4 4 tmaxJ
Wear Resistance - cycles 3.13 400 (rmn ) 400 (min )
3.11
Formability - in 3.14 5/9 1/2
Blister Resistance - sec
16 12
3.15 5t.s, 40
FORMICA® LAMINATE BY FORMICA GROUP
TECHNICAL DATA (GENERAL PUPOSE GRADE 10 AND POST -FORMING GRADES 12 & 20) coNT
FIRE TEST DATA - ASTM E-84
Formica Corporation conducts and rnarntains an active lire test-
ing program to provide code regulators, architects, and designers
with current information on a variety of panel assemblies. Fire test
data using Formica" Brand Laminate sheets (grades 10/HGS,
12HGP, and 20/VGP) is available upon request. Contact Formica'
Technical Services at 1-800-FORMICAru (option 2) or 513-786-
3578 for assistance.
CODES AND SPECIFICATIONS
FORMICA BRAND LAMINATE
(GENERAL PURPOSE - GRADE 10/HGS / HORIZONTAL APPLICATION)
U.S. Federal Specification, LP-508-H, Style D, Type I, Class 1
U.S. Military Specification, MIL-P-17171E(SH). Type I
FMVSS 302
NSF Standard 35
ASTM-G22 Approved
City of New York, Board of Standards and Appeals,
MEA No. 326-86M
GREENGUARD CERTIFICATION
FORMICA BRAND LAMINATE
(POST -FORMING - GRADE 12/HGP / HORIZONTAL APPLICATION)
U.S. Federal Specification. LP-508-H. Style D. Type II. Class 1
FMVSS 302
NSF Standard 35
City of New York, Board of Standards and Appeals.
MEA No. 327-86M
GREENGUARD CERTIFICATION
FORMICA BRAND LAMINATE
(POST -FORMING - GRADE 20/VGP / VERTICAL APPLICATION)
U.S. Federal Specification, LP-508-H. Style D. Type II. Class 2
CFR Pad 3280 IviainifacIuring Horne Construction acid
Safety Standards
FMVSS 302
NSF Standard 35
GREENGUARD CERTIFICATION
SIZES
Sheet widths 36" (914nm1), 48" (1219mm), 60" (1524mrn)
Sheet lengths: 96" (2438inm, 120" (3048inin), 144' (3658nim)
THICKNESS
TYPICAL NEMA
THICKNESS THICKNESS RANGE
Grade 10 (HGS) 045' 1. urm .0.3" - .053' Ulanm - 1.:2ron
Grade 12 (HGP)
034' - 044• (0 88mm 1 2mm)
Grade 20 (VGP) 026' (0 7mm1 024' - 032' (0 6mm 0 Smm)
WEIGHT PER SQUARE FOOT
Grade 10/HGS: 0.324 pounds
Grade 12/HGP: 0.252 pounds
Grade 20/VGP: 0.180 pounds
1E0
TO ORDER FORMICA BRAND LAMINATE SAMPLES,
PLEASE CALL
U.S.: 1-800-FORMICA'" (select option 1)
Canada. 1-800-363-1405 for ZIP -CHIP service
HOW TO SPECIFY
Surface (and appropriate backing sheet) shall he Formica Brand
Laminate by Formica Group, Cincinnati. Ohio.
COLOR NUMBER
COLOR NAME
GRADE
FINISH
SIZE
USE AND CARE
Refer to Formica Brand Laminate Use and Care Guide Form No.
YLT 02358w for specific details.
Formica Brand Laminate slieef may be cleaned with a darnp clot)
and mild detergent.
II in doubt aboul the suitability of a particular cleaner or detergent.
check with its manufacturer, Use of abrasive cleaners. powders,
scouring pads, steel wool, sandpaper etc., can damage the finish
of the decorative surface and are not recommended.
Acid or alkaline -based cleaners. compounds, etc., will Haar. etch,
corrode, and permanently discolor the decorative surface of
laminate. Never use these materials on laminate, nor allow bottles.
rags, etc., contaminated with them to contact the surface.
Accidental spills or splatters Iron) these harsh materials should
be wiped off immediately. and the area cleaned thorouglily with
a damp cloth.
FORMICA® LAMINATE BY FORMICA GROUP
TECHNICAL DATA (GENERAL PUPOSE GRADE 10 AND POST -FORMING GRADES 12 & 20) CONTINUED
LIMITED WARRANTY
Formica Corporation expressly warrants That, for a period of one
(1) year from the date of first sale, these products will be reason
ably free of defects in materials and workmanship, and that when
properly handled and fabricated, will conform, within accepted
tolerance. to applicable manufacturing specifications. Colors
subject to dye lot variations. This limited warranty only applies
to Formica Brand Laminate which is stored, handled, fabricated
and installed in the manner recommended by Formica Corpora-
tion. Due to the variety of uses and applications 10 which Formica
Brand Laminate may be put, FORMICA CORPORATION CAN MAKE NO
WARRANTY THAT THIS PRODUCT IS SUITABLE FOR ANY PARTICULAR
PURPOSE AND CAN MAKE NO OTHER WARRANTIES, EXPRESS
OR IMPLIED, OTHER THAN THOSE SET FORTH ABOVE.
DISCLAIMER OF WARRANTIES
THE WARRANTIES SET FORTH HEREIN OR IN FORMICA CORPORA-
TION'S WARRANTY DOCUMENTS WITH RESPECT TO A PRODUCT
ARE THE ONLY WARRANTIES MADE BY FORMICA CORPORATION IN
CONNECTION WITH THESE PRODUCTS, AND ARE EXPRESSLY IN LIEU
OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY
FORMICA CORPORATION ARE SOLD ONLY TO THE SPECIFICATIONS
SPECIFICALLY SET FORTH BY FORMICA CORPORATION IN WRITING.
FORMICA CORPORATION'S SOLE OBLIGATION FOR A REMEDY TO
BUYER SHALL BE REPAIR OR REPLACEMENT OF NON -CONFORMING
PRODUCTS, OR AT THE OPTION OF FORMICA CORPORATION, RETURN
OF THE PRODUCT AND REFUND OF THE PURCHASE PRICE. BUYER
ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF
THE PRODUCTS PURCHASED, WHETHER USED SINGLY OR IN
COMBINATION WITH OTHER SUBSTANCES.
LIMITATION OF LIABILITY
No claim by buyer of any kind, including claims for indemnifica-
tion, whether as to quality or amount of products delivered or
for non -delivery of products, shall be greater in amount than. the
purchase price ct the products in respect of which damages are
claimed. IN NO EVENT SHALL FORMICA CORPORATION BE LIABLE
TO BUYER FOR ANY SPECIAL, INDIRECT, INCIDENTAL, RELIANCE,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES OR COVER, OR LOSS
OF PROFIT, REVENUE OR USE, IN CONNECTION WITH, ARISING OUT
OF, OR AS A RESULT OF, THE SALE, DELIVERY, SERVICING, USE OR
LOSS OF USE OF THE PRODUCTS SOLD HEREUNDER, OR FOR ANY
LIABILITY OF BUYER TO ANY THIRD PARTY WITH RESPECT THERETO.
BUYER SHALL INSPECT FOR NONCONFORMITY PROMPTLY UPON
RECEIPT, Failure by buyer to give Forrlir;a Corporation written
notice of elen t within 30 clays from date of delivery or, in the case
of non -delivery from the date fixed for delivery. shalt constitute a
waiver by buyer of all ciaiuns in respect of such products.
FTB-0824 Rev 2 (00-19-14(
gcaesarstone°
Caesarstone® is a quartz -based fabricated stone which can be used for attractive and functional
countertops, shower and tub surrounds, interior wall cladding, and other interior applications.
Compared to natural stone surfacing, Caesarstone offers many attractive advantages including
greater strength, wear resistance, ease of handling, and a unique aesthetic character.
Edit this Guide Specification according to project requirements. Samples, product literature, and
design assistance are available by contacting Caesarstone at 877-978-2789 or by visiting
caesarstoneus.com. Since fabrication and installation of Caesarstone are similar to that of
natural stone, publications such as the Marble Institute of America's Dimension Stone Design
Manual can also be consulted.
SECTION 06 61 19 — QUARTZ SURFACING FABRICATIONS
SECTION 12 36 61 — QUARTZ SURFACING COUNTERTOPS
PART 1 GENERAL
1.0 RELATED DOCUMENTS
Drawings and general provisions of the contract, including general and supplementary
conditions and Division 1 Specification Sections, apply to this section.
1.01 SUMMARY
Coordinate the following with terminology used to identify Caesarstone on drawings. In most
instances, Caesarstone should be called -out as "Quartz Surfacing."
A. Section Includes: [Quartz surfacing] [Engineered stone] [Stone] for
1. Countertops
2. Interior [wainscots] [and] [wall cladding]
3. [Shower] [and] [bath] enclosures
4. Window Sills
5. Vanity Tops
6. Table Tops
7. Bar tops
8. Seating
9. Cold Cafeteria Surfaces
10. Interior Steps
11. Hot Cafeteria Surfaces
12, Reception Areas
13, Nurses' Stations
14. [
15. Other interior applications as shown
B. Related Sections
1. Division 1 —
2. Division 1 —
3. Division 5 —
4_ Division 6 —
1
on drawings
Administrative, Procedural and Temporary Work Requirements
"LEED Requirements" for Additional LEED Requirements
Section Metal Fabrication for Blocking
Section Rough Carpentry for Blocking
Version 3 2 lune 14, 2013
i5caesarstone°
5. Division 6 -Solid Surface Fabrications
6. Division 7 - Section Joint Sealers
7. Division 9 - Section Solid Surface Wall Cladding
8. Division 9 - Section Quartz Surface Wall Cladding
9. Division 10- Quartz Surface Toilet Partitions
10. Division 15 - Plumbing Fixtures
11. Division 16 - Wiring Devices
Templates may be required for sinks and plumbing trim, stove tops, hardware, etc.
Templates showing cutouts required for installation of items installed on or penetrating through
quartz surfacing shall be provided under Sections where items are specified.
[Indicate if [sink] [and] [lavatory] cutouts are for top mount or under cabinet installation.]
C. ALTERNATES: Refer to Division 1 Section "Alternates" for description of work in this section
affected by alternates.
1.02 REFERENCES
A. ASTM International
1. ASTM C97 - Absorption and Bulk Specific Gravity of Dimension Stone
2. ASTM C99 - Modulus of Rupture of Dimension Stone
3. ASTM C170 - Compressive Strength of Dimension Stone
4. ASTM C217 - Weather Resistance of Slate
5. ASTM C482 - Bond Strength of Ceramic Tile to Portland Cement
6. ASTM C484 - Thermal Shock Resistance of Glazed Ceramic Tile
7. ASTM C501 - Relative Resistance to Wear of Unglazed Ceramic Tile by the Taber
Abraser
8. ASTM C531 - Linear Shrinkage and Coefficient of Thermal Expansion of Chemical -
Resistant Mortars, Grouts, Monolithic Surfacing, and Polymer Concretes
9. ASTM C880 - Flexural Strength of Dimension Stone
10. ASTM C1026 - Resistance of Ceramic Tile to Freeze -Thaw Cycling
11. ASTM C1028 - Static Coefficient of Friction of Ceramic Tile and Other Like Surfaces
by the Horizontal Dynamometer Pull -Meter Method
12. ASTM C1243 - Relative Resistance to Deep Abrasive Wear of Unglazed Ceramic
Tile by Rotating Disc
13. ASTM D256 - Izod Pendulum Impact Resistance of Plastics
14. ASTM D2047 - Static Coefficient of Friction of Polish -Coated Floor Surfaces by the
James Machine
15. ASTM E84 - Surface Burning Characteristics of Building Materials
B. American National Standards Institute (ANSI)
1. ANSI Z124.6 - Stain Resistance
2. ANSI/N 42.14 - Radiation
C. National Electrical Manufacturers Association (NEMA)
1. NEMA LD3-3.5 - Boiling Water Resistance
2. NEMA LD 3-3.6 - High Temperature Resistance
D. European Standards (EN)
1. EN 14617-1 - Determination of Apparent Density and Water Absorption
2. EN 14617-4 - Determination of Abrasion Resistance
Version 3 2. June 14, 2013
caesarstone
3. EN 14617-5 - Determination of FreezerThaw Resistance
4. EN 14617-9 - Determination of Impact Resistance
5. EN 14617-12 - Determination of Dimensional Stability
6. EN 14617-13 - Determination of Electrical Resistivity
7. EN 14617-15 - Determination of Compressive Strength
E. ISO (International Organization for Standardization)
1. ISO 9002 - Model for Quality Assurance in Production
2. ISO 14001 - Environmental Management Systems
F. Others
1. NSF - ANSI/NSF Standard 51
2. MEA - New York Materials and Equipment Acceptance
3. OHSAS - 18001- Occupational Health & Safety System
4. GREENGUARD - "Children and Schools"
5. SCS - Certified recycled content
6. Kosher
1.03 SUBMITTALS
A. Product Data
1. Quartz Surfacing: Submit manufacturer's product data, [sample warranty form,] and
fabrication and installation instructions.
2. Accessories: Submit manufacturer's product data and installation instructions.
B. Shop Drawings: Identify color[s] and finish[es], and show the following:
1. Field -verified dimensions
2. Quartz surfacing dimensions
3. Locations and dimensions of cutouts
4. Required locations of support and blocking members;
5. Edge profiles
6. Installation details and methods
C. Samples
Coordinate Subparagraphs 1, 2, and 3 with the color specifications in Part 2 - Products,
1. Cut sample and seam together for representation of seaming techniques.
2. Indicate full range of color and pattern variation.
3. [Samples for Color Selection: Submit [two] [ ] sets of manufacturer's
standard colors and finishes.]
4. Samples for Color Approval: Submit [two] [ 1 samples, 10 x 5 inches, (250 x
125 mm) of [each] color and finish selected.
5. Stone Adhesive: Submit [two] [ 1 samples of an adhesive joint for [each] color
quartz surfacing selected. Show color match of adhesive.
D. Fabricator Qualifications: Submit evidence of fabricator's qualifications.
E. Closeout Submittals: Submit completed warranty form.
F. LEED Submittals: Provide LEED submittals as required.
Version 3.2. lune 14, 2013
Ycaesarstone°
G. Product Certificates: For each type of product, provide product certificates signed by product
manufacturer.
H. Maintenance Data
1. Submit manufacturer's care and maintenance data.
2. Include in project closeout documents.
1.04 QUALITY ASSURANCE
A. Applicable Standards
1. Standards of the following, as referenced herein:
a. American National Standards Institute (ANSI)
b. American Society for Testing and Materials (ASTM)
c. National Electrical Manufacturers Association (NEMA)
d. NSF International
e. International Organization for Standardization (ISO)
2. Fire Test response characteristics
a. Provide with the following Class A (Class 1) surface burning characteristics as
evidenced by testing identical products against ASTM E84 (UL 723) or another
testing and inspecting agency acceptable to authorities having jurisdiction.
b. Flame Spread Index: 25 or less
c. Smoke Developed Index: 450 or less
B. Allowable Tolerances
1. Variation in component size ± 1/8" (3mm) over a ten (10) foot length
2. Location of openings: ± 1/8" (3mm) from indicated location
3. Maximum 1/8" (3mm) clearance between quartz surfaces and each wall
1.05 DELIVERY, STORAGE, AND HANDLING
A. Packaging, Shipping, Handling, and Unloading
1. Observe manufacturer's recommendations and handle accordingly in order to prevent
breakage or damage.
2. Brace parts if necessary.
3. Transport in the near -vertical position with finished face turned toward finished face.
4. Do not allow finished surfaces to rub during shipping or handling.
B. Storage and Protection
1. Store in racks in near -vertical position.
2. Prevent warpage and breakage.
3. Store inside away from direct exposure to sun.
4. Store between 25°F and 130°F (-4 °C and 54°C).
5. Store with finished face turned toward finished face,
1.06 WARRANTY
A. Commercial: Provide manufacturer's Limited Commercial 10-Year Warranty against product
defects when fabricated and installed by a Caesarstone certified fabricator.
B. Residential: Provide manufacturer's Residential Lifetime Warranty against product defects
when fabricated and installed by a Caesarstone certified fabricator.
Version 3.2. June 14, 2013
Ycaesarstone•
PART 2 PRODUCT
2.01 MANUFACTURERS
A. Qualifications: Manufacturer shall be ISO 9002 and ISO 14001 certified.
B. Acceptable Manufacturer: Provide Caesarstone Quartz Surfacing distributed by U.S.
Quartz Products Inc. (Caesarstone U.S.A., Inc.); Van Nuys, CA; phone 877-9-QUARTZ
(978.2789); www.caesarstoneus.com.
The following product is included as a convenience to specifiers who require multiple
suppliers. It is not warranted or recommended by Caesarstone.
C. Substitutions: Zodiaq manufactured by DuPont may be substituted in accordance with
[Instructions to Bidders.] [Section 01 25 00 — Substitution Procedures.]
2.02 QUARTZ SURFACING
A. Composition: 93 percent crushed quartz aggregate combined with resins and pigments and
fabricated into slabs using a vacuum vibro-compaction process.
Due to its superior flexural strength compared to natural stone, Caesarstone can be fabricated
in larger sized pieces. This may reduce the number of joints in an installation, which is more
economical and may produce a better -looking end result. It may also allow the use of thinner
material, producing additional economies and weight reductions.
Thickness: 3/4" (2 cm) is the minimum recommended for countertops; use 1-1/4" (3 cm)
material when greater strength or thicker edges are required.
B. Dimensions
1. Thickness: Nominal [3/4 inch (20 mm)] [1-1/4 inches (30 mm)] [As shown on
drawings.]
2. Size: Slabs shall be not less than [56.5 x 120 inches (1.44 x 3.05 m)] to minimize the
number of joints used in installation.
The back of each slab of Caesarstone is imprinted with a trademarked zigzag pattern to
simplify jobsite identification.
C. Identification: Material shall be labeled with a batch number and imprinted with a
manufacturer's identifying mark on the back.
Version 3 2 June 14, 2013
gcaesarstone
D. Performance - Caesarstone Quartz Surfaces Technical Data
Test Performed
Physrtal Propr<rtre
Water Absorption
0ensrty
Flexural Strength
Dimension Stability
Electrical Stability
Durahilir
Impact Resistance
Compressive Strength
Abrasior
Freeze -Thaw Resistance
Test Standard
ASTM C97
ASTM C97
EN 14617-1
ASTM C880
EN 14617.2
EN 14617-12
EN 14617-13
ASTM D1709'
EN 14617-9
ASTM C170
EN 14617.15'
ASTM C501
ASTM C1243
EN 14617-4
ASTM C1026
EN 14617-5
Results
c0 05%
22-24gr/cm'
22.24grlon'
6.500-10,770 psi; 44 8-74 3 MPa
57 6-70 IvtPa
Class A
volume resrsrarsce (R) = 0 92 x 10"-0
Volume resis!ivrty (p) = 4 88 x 10' ' Om
26 3 Ibs (1 17N)
4,000 - 10,000 01
21,312 • 27,133 psi
178 3-210.6 MPa
216-696
Volume of chord V=132.244 min
Groove length = 21 8 mm or V=86 mm'
No defects after 15 freeze -thaw cycles
No defects after 25 freeze -thaw cycles
Mohs Hardness Scale 6 5-7
S! r rr C hc:,nca1 Rt-asr,rren .rid Atmity
Stain Resistance ANSI 2124 6 Pass
Wear and Cleanabrlily ANSI Z124.6 Pass
Chemical Resistance ANSI 2124.6 Pass
EN 14617-10 Class C.
lherer,r Pr),p<rr.. <. _
Linea! Thermal Expansion ASTM D696 •30 10 .30'C 1 3.1 9 x 10' cnVCrn/ C
EN 14617-11 -30 to +30•C. 2 1 x 10' ('C ),
-30 to +60'C 2 7 x 10 CC
Thermal Conductivity 'EN 1266415O 8301 1 75 W/m I'K (mean T of 10-C1
Thermal Shock EN 14617-6 No visual defects after 10 cycles
Loss in mass = 0 02%-0 05%
Loss in flexural strength = 0 7%-1 1%
Boding Water Resistance NEMA LD3.3.5 Pass
High Temperature Resistance NEMA LD3-3 6 Pass
:afet .
Cigarette Tesl ANSI 2174 6 Pass
Surface Burning ASTM E84 Class 1 and Class A
Fire Classification EN 13501-! Wall claddang B-sl-d0
Fluohng and stairs 8-Ibs1
Stab( Coeferctent of Fnct.on ASTM C 1028 As reserved -- Dry 0 8, Wet 0 6
As renovated — Dry C 9. Wet 0 6
Shp Resistance DIN 51130 04 wet ramp R9.10
DIN 51097 Wei barefoot ramp C
EN 14231 Wet 13-21 SRV, Dry 43-53 SRV
AS/N2S 4586 Four S rubber pendulurr 25-30 BPN
Wei barefoot ramp 8
OBI wet ramp R 10
Rad"atron ANSIM 42 14 Re = 1 4-6 8
Tr = 1 4-3
K = <3 303
ten/kg dry werghn
Notes: Test reports and certifications can be viewed at www.caesarstoneus.com
Recalls represe"! a range Some models requ+re srrr,hb.rg to remcvc ;tarn,
Version 3.2 June 14, 2013
caesarstone'
Certifications and Approvals
ISO 14001 Environmental Management Systems
Certified by IONet Certificate f! IL-44679
ISO 9001 Quality Systems - Model for Quality Certified by IQNet Certificate 8 IL-29318
Assurance in Production, Installations,
and Servicing
OHSAS 18001
Health and Safely Systems
Certified by lONet Certificate 8 IL-43226
Kosher Certified by Rabbre Yisrael Rozen,
the Zomet Institute
Certificate 8 58-003-523-6
GREENGUARO Certified for `Indoor Air Quality"
and 'Children and Schools"
Caesarstone is a tow -emitting material
Scientific Certification Systems (SCS) Recycled Content Certified by SCS
See page 11
New York City Materials and
Equipment Acceptance (MEA)
Approved by City of New York MEA 202-08-M
ANSI/NSF Stnadard 51
Food Equipment Materials Listed by NSF
Sale to use in food preparation areas
E. Color and Finish
Caesarstone - Polished: 41 stocked colors.
Caesarstone - Honed: 3 stocked colors. Note that dark honed colors will show fingerprints
and require increased maintenance,
Caesarstone - Recycled: 2 stocked SCS certified recycled content colors.
Caesarstone - Motivo: 3 stocked patterned finishes
Custom Colors and Finishes: Available without additional charge on orders of 4,500 sq. ft. or
more.
Edit the following according to color selection method and coordinate with submittals.
1. Provide color[s] and finish[es] selected by [architect] [ 1 from manufacturer's
stocked standards. [Allow for selection of up to [two] [four] [ 1 colors.]
2. Provide custom color and finish to match [sample in [architect's] [ 1
office.]( .]
All standard colors are available with polished finish. See color charts or samples for
availability of honed finish.
3. Provide [Buttermilk, Color No. 4220] [
with [polished] finish.
4. Finish
a. Polished surface shall have gloss greater than or equal to 35% at 50°.
b. Honed surface shall have a matte finish.
, Color No. ]
Retain the following if edges and corners are not detailed on drawings.
F. Exposed Edges [and Corners]
1. Countertops
a. Edges: [Square] [Bullnose] [Beveled] [Waterfall] [ 1 profile, [single]
[double] layer thick
Version 3.2- June 14, 2013
caesarstone
b. Outside Corners: [Square] [[3/4 inch (20 mm)] [ inch[es] ( mm)]
radius]
2. [Backsplash] [and] [Wall Cladding]
a. Edges: [Square] [ 1
b. Outside Corners: [Square butt joints] [ 1
2.03 ACCESSORIES
A. Mounting Adhesives
1. Provide structural -grade silicone or epoxy adhesives as recommended by
manufacturer for application and per conditions of use.
2. Acceptable Silicone Manufacturers
a. Dow Corning°
b. GE Sealants and Adhesives
c. [ 1
3. Acceptable Epoxy Manufacturers
a. Akemi North America
b. Bonstone Materials Corporation
c. Tenax U.S.A.
d. [ 1
4. Provide spacers, if required, of type recommended by adhesive manufacturer.
B. Stone Adhesive
1. Provide epoxy or polyester adhesive of type recommend by manufacturer for
application and conditions of use.
2. Acceptable Manufacturers
a. Akemi North America
b. Bonstone Materials Corporation
c. Tenax U.S.A.
d. [ 1
3. Color: Adhesive that will be visible in finished work should be tinted to match quartz
surfacing.
In most countertop and interior cladding applications, Caesarstone can be installed with
structural adhesive. Where required, however, Caesarstone can also be set in grout or
installed with ties, clips, or other types of hardware recommended for thin stone veneers. Edit
below and coordinate Section as required.
C. [Fasteners] [Grout] [Hardware]: [ 1
D. Joint Sealants
1. Clear silicone sealant as recommended by manufacturer for application and per
conditions of use.
2. Provide anti -bacterial type in [toilet] [and] [bath] rooms,] [food preparation areas,j [and]
1.
3. Acceptable Manufacturers:
a. Dow Corning°
b. GE Sealants and Adhesives
c. r
Version 3 2 June 14, 2013
5caesarstone
E. Solvent: Product recommended by adhesive manufacturer to clean surface of quartz
surfacing to assure adhesion of adhesives [and sealants].
F. Cleaning Agents: Non-abrasive, low pH cleansers.
2.04 FABRICATION
Include manufacturer authorization if manufacturer's warranty is specified.
A. Fabricator: Firm shall have five years' experience fabricating architectural stone and shall
have water-cooled cutting tools. [Firm shall be authorized in writing by manufacturer.]
B. Shop Assembly: Observe proper safety procedures and comply with manufacturer's
instructions.
C. Layout: Layout joints [as shown on drawings.] [to minimize joints and to avoid L-shaped
pieces of quartz surfacing.]
D. Inspect Material
1. Inspect material for defects prior to fabrication.
2. Color Match
a. Materials used throughout the project shall be from the same batch and bear
labels with the same batch numbers.
b. Visually inspect materials to be used for adjacent pieces to ensure acceptable
color match.
c. Inspect in lighting conditions similar to those existing at the jobsite.
3. Variation in distribution of aggregates in quartz surfacing that is within manufacturer's
tolerances is not a defect.
E. Tools: Cut and polish with water-cooled power tools.
F. Cutouts
As with any type of stone, smaller radii increase potential for crack propagation at inside
corners; in no case should radius Tess than 3/8 inch be used.
1. Cutouts shall have [3/8 inches (10 mm)] [ inches ( mm)] minimum inside
corner radius. Inside corners shall be reinforced in an acceptable manner to prevent
cracking.
2. Polish edges where they will be exposed in finished work.
The following is recommended in areas subject to heavy usage or where additional strength
is justified:
3. [If the remaining material outside a cutout is less than [three inches (76 mm)] [
inches ( mm)] wide, reinforce area by laminating it with a strip of quartz surfacing.]
G. Laminations: Laminate layers of quartz surfacing as required to create built-up [edges,] [trim,]
[and other areas requiring additional thickness].
Version 3.2 lune 14, 2013
AMERICAN
ENGINEERING
TESTING, INC.
PROJECT:
MATERIAL CHECK
AET PROJECT NO: 20-11101
CONSULTANTS
ENVIRONMENTAL
• GEOTECHNICAL
• MATERIALS
• FORENSICS
REPORT OF STONE TESTING
REPORTED TO:
REALSTONE SYSTEMS
560 KIRTS BOULEVARD
SUITE 120
TROY, MI 48084
DATE: November 1, 2012
Product Type:
Date Tested:
Roman Beige
10/22/10 to 10/26/12
Conformance: The stone samples meet ASTM:C568-10 medium -density requirements for Limestone
dimension stone.
Sample
B C D E Average Requirements
ASTM C568
Strength Properties: ASTM C170- WET CONDITION - PERPENDICULAR
Compression Strength, psi: 13,330 14,910 11,480 7,430 8,710 11,170 4,000 Min
Strength Properties: ASTM C170 - DRY CONDITION - PERPENDICULAR
Compression Strength, psi: 11,190 14,450 21,820 21,050 12,560 16,210 4,000 Min
Strength Properties: ASTM C170 - WET CONDITION - PARALLEL
Compression Strength, psi: 6,590 6,600 7,450 4,260 7,260 6,430 4,000 Min
Strength Properties: ASTM CI70 - DRY CONDITION - PARALLEL
Compression Strength, psi: 19,490 23,440 27,260 17,290 11,700 19,840 4,000 Min
Modulus of Rupture, psi:
Flexural Strength, psi:
Modulus of Rupture, psi:
Flexural Strength, psi:
Strength Properties: ASTM C99 & C880 - WET CONDITION -
810 800 720 810 810 790
700 880 930 690
850 840 1,170 910 990 960
1,130 730 980 1,070
Strength Properties: ASTM C99 & C880 - DRY CONDITION
1,740 1,300 1,750 1,390 1,280
1,960 1,480 1,220 1,730 910
1,500 1,400 1,460 1,250 1,480
1,020 1,170 1,450 1,730 1,510
500 Min
1,450 500 Min
1,400
550 Cleveland Avenue North 1St. Paul, MN 55114
Phone 651-659-9001 (Toll Free 800-972-6364 (Fax 651-659-1379 jwww.arnengtest.com IAA/EEO
This document shall not oe reproduced. except in full, without written approvai from American Engineering Testing. Inc
rril5ft:riP,ySternscorn >E,
Sample
Specific Gravity:
Bulk Density, pcf:
Absorption, %
AET Project No. 20-11101 Page 2 of 2
A
Physical Properties: ASTM:C97
2.408 2.417 2.425
150.3 150.8 151.3
4.1 4.2 3.9
Remarks: The samples were destroyed during testing and discarded.
Report Prepared By:
John J. Haupt, PE
Staff Engineer 11
For additional help or with questions please contact us
at 1-866-698-5066 or at realstonesystems.com
US Office
560 Kirts Blvd., Suite 120
Troy, MI 48084 USA
248-614-6613
Average
2.417
150.8
4.1
Report Reviewed By:
John Amundson
Principal Engineer
Canada Office
464 Brierwood Ave.
Ottawa, ONT. K2A2H3 CA
613-321-5866
Requirements
ASTM C568
135 Min.
7.5 Max
AMERICAN
ENGINEERING
TESTING, INC.
REPORT OF FREEZE -THAW TESTING OF STONE
PROJECT:
MATERIAL EVALUATION
ROMAN BEIGE -STONE UNITS
REPORTED TO:
REALSTONE SYSTEMS
560 KIRTS BLVD
SUITE 120
TROY, MI 48084
ATTN: STEVE HODGES
AET JOB NO: 20-11101 DATE: JANUARY 29,2013
CONSULTANTS
• ENVIRONMENTAL
• GEOTECHNICAL
• MATERIALS
FORENSICS
INTRODUCTION
This report presents the test results on five stone units. Samples were submitted and identified
by you. The scope of our work consisted of conducting freeze -thaw testing in accordance with
ASTM C67-I2, "Standard Test Methods for Sampling and Testing Brick and Structural Clay
Tile" and evaluated according to ASTM C 216-12a "Standard Specification for Facing Brick
(Solid Masonry Units Made from Clay or Shale)." Our work was authorized by you on February
20,2012.
SAMPLE INFORMATION
American Engineering Testing, Inc. received 5 stone samples identified as Roman Beige #1
through #5 from Realstone Systems.
TESTING METHODS
The specimens were subjected to freeze -thaw cycling in accordance with ASTM C67.
1. The samples were placed in a pan with water at a depth of } " and frozen for 20 hours. Next
the samples were immersed in a thawing tank for 4 hours. This process continued for 50
cycles or until the specimens develop a crack or appears to have lost more than 3% of its
original weight by disintegration as judged by visual inspection.
2. Final weight loss percentages are calculated by dividing the oven dry weight of dislodged
material by the final oven dried sample weight, plus the total dislodged material.
TEST RESULTS
Sample
Weight
Loss %
Full
Width
Cracking
Rating
RBI
0.42%
Yes
See Remarks
RB2
1.74%
Yes
See Remarks
RB3
62.83%
Yes
See Remarks
RB4
55.27%
Yes
See Remarks
RB5
0.47%
Yes
See Remarks
Average
24.14%
REMARKS
The samples were tested for 50 freeze thaw cycles and did not to meet the specifications of
ASTM C216-12a "Standard Specification for Facing Brick (Solid Masonry Units Made from
Clay or Shale)" for SW facing material. This report represents specifically the samples tested.
The ASTM C216 requirements for freeze thaw durability in 6.1.3.1 state that no individual unit
separates or disintegrates resulting in a weight loss greater than 0.5% of its original dry weight.
Additionally, ASTM C2I6, Section 6.1.3.2 states that no individual unit develops a crack that
exceeds, in length, the units least dimension. All samples exhibited unsatisfactory weight loss,
full width cracking or both. If you have any questions, please feel free to call us.
Report Prepared By:
American Engineering Testing, Inc.
Josepji T. Johnson
Conc ete Technician III
Phone: 651-659-1354
Fax: 651-647-2744
itjohnson@amenetest.com
Report Reviewed By:
American Engineering Testing, Inc.
(.Y. V ^A"IrtvT
Daniel M. Vruno, P.E.
Principal Engineer
MN Lic. No. 42037
Phone: 651-659-1334
Fax: 651-647-2744
dvruno@amengtest.com
For additional help or with questions please contact us
at 1-866-698-5066 or at realstonesystems.com
US Office
560 Kirts Blvd., Suite 120
Troy, MI 48084 USA
248-614-6613
Canada Office
464 Brierwood Ave.
Ottawa, ONT. K2A2H3 CA
613-321-5866
re li tt){1f-, y,tcrnscorn out..';n_�t.�
HOOVER
TREATED
WOOD PRODUCTS, INC.
Material Safety Data Sheet
PYRO-GUARD® Treated Wood
NFPA Ratings
FbmmpMny
Section 1. Chemical Product and Company Identification
Product / Trade Name PYRO-GUARD® Treated Wood
Synonyms Fire Retardant Treated Wood(FRTW), Interior FRTW
Product Use Controls Flame Spread and Maintains Strength Under Fire Conditions Longer Than Untreated Wood
MSDS Number HTWP-039 Revision 5/19/2009
Manufacturer Hoover Treated Wood Products, Inc.
154 Wire Road NW
Thomson, GA 30824
(706) 595-5058 (Non -Emergency) http://www.frtw.com
Emergency Phone (M-F 8am-5:30pm eastern) (706) 595-7355
Section 2. Hazards Identification
HMIS
Note: Personal protective equipment (PPE) is related to conditions of use.
Health Hazard D
;
Determination of PPE is the responsibility of the employer. Refer to
(ExposureProtection)
Section 8 Controls t Personal of this MSDS for
1 ``
� ��,,, �,
Reactivity 0
recommendations.
Personal Protection
Emergency Overview
than the wood before treatment. Wood species dictates appearance and
Pine is the predominant species used. Sapwood is yellowish white
of finely divided particles generated from sawing, sanding, routing, or
products.
chips from the product may cause mild irritation of the eyes, skin,
may form explosive dust/air mixtures if high concentration of product
Product appearance and odor is no different
odor. Generally a light to dark brown solid. Southern
and heartwood, reddish brown. Wood dust consists
chipping solid dimensional lumber or other wood
Acute or prolonged exposure to wood dust or
gastrointestinal tract and respiratory tract. Product
dust is suspended in air.
Potential Health Effects
dust may cause nose, throat or lung irritation. Various species of
response in sensitized persons.
may cause mechanical irritation.
skin exposure to splinters. Prolonged and/or repeated contact with treated or
mild irritation. Various species of untreated wood dust can elicit allergic type
Effects: Wood dust, depending on species, may cause dermatitis on
sensitization and/or irritation.
Inhalation: Airborne treated or untreated wood
untreated wood dust can elicit allergic respiratory
Eye Contact: Treated or untreated wood dust
Skin Contact: Handling wood may result in
untreated wood dust or chips may result in
skin irritation in sensitized persons.
Ingestion: Not anticipated to occur.
Chronic Wood Dust (treated or untreated)
prolonged, repetitive contact; may cause respiratory
Continued On Next Page
Page I of9
Effective Date: 5/19/2009
PYRO-GUARD Treated Wood
Potential Environmental Effects
No known significant environmental effects.
Section 3 Composition / Information On Ingredients
CAS #
Component
Approximate % By Weight'
Not Available
Wood / Wood Dust
> 88%
Proprietary
Boron Compounds
< 4%
Proprietary
Nitrogen Compounds
< 4%
Proprietary
Phosphorous Compounds
< 3%
Proprietary
Sodium Compounds
< 1 %
1897-45-6
Tetrachloroisophthalonitrile
< 0.02 %
1 The values presented will vary due to the variability of treatment and the natural variability of wood
Section 4. First Aid Measures
Inhalation: Remove from wood dust exposure. If breathing has stopped administer artificial respiration. Seek medical aid
if symptoms persist.
Eye Contact: Gently flush any particles from the eyes with large amounts of water for at least 15 minutes. DO NOT RUB
THE EYES. Seek medical aid if irritation persists.
Skin Contact: Rinse wood dust off with water. DO NOT RUB. Once the skin is free of the wood dust, wash thoroughly
with soap and water. Wash contaminated clothing before reuse. Seek medical aid if severe irritation develops.
Ingestion: Rinse the victim's mouth out with water. Do not induce vomiting. If symptoms develop, call a physician or
poison center at (800) 222-1222.
Section 5. Fire Fighting Measures
Flammable Properties
This product resist burning - Class A per ASTM E-84 (Flame Spread <25). Fire from a separate fuel source may be
intense enough to cause thermal decomposition releasing toxic fumes and/or gasses. Wood dust is combustible, and
may form explosive mixtures with air in the presence of an ignition source.
Extinquishinq Media
Suitable Media: Water Fog, Foam, CO2, or Dry Chemical - Use methods for the surrounding fire.
Continued On Next Paee
Page 2 ot9
Effective Date: 5119/2009
PYRO-GUARD® Treated Wood
Protection of Firefighters
Specific Hazards: Wood dust may present a strong to severe explosion hazard if dust cloud contacts an ignition source.
Use water to wet down wood dust to reduce likelihood of ignition or dispersion of dust into air. Remove burned or wet
dust to open area after fire is extinguished. Combustion or thermal decomposition can yield dangerous fumes of
phosphorous compounds, nitrogen compounds, boron compounds, sodium compounds, carbon dioxide, carbon
monoxide, aliphatic aldehydes, organic acids, or polycyclic aromatic hydrocarbons.
Protective Equipment and Precautions: Wear complete fire service protective equipment (Full Bunker Gear), including
full -face NIOSH and NFPA — approved self-contained breathing apparatus (SCBA). Avoid inhaling any combustion
products.
Section 6. Accidental Release Measures
Personal Precautions: None necessary.
Environmental Precautions: None necessary.
Methods for Containment: Product is an article - none necessary.
Methods for Clean-up: None necessary.
Other Information: No additional information available.
Section 7. Handling and Storage
Handling
Do not generate airborne dust in the presence of an ignition source when sawing, cutting, sanding, grinding, routing or
chipping wood. Wash hands after handling and before eating. Avoid contact of wood dust with skin and eyes. Avoid
breathing wood dust. Avoid skin penetration by wood splinters. Launder clothing worn when generating wood dust before
reuse. Do not eat, drink, or smoke when handling this product or in areas where dust of this product are present. Use
appropriate personal protective equipment (PPE).
Storage
Protect from physical damage. Store PYRO-GUARD treated lumber and plywood off the ground, in a dry place,
protected from weather. Exposure to weather may impair product's performance. While at the job site, before installation,
cover with plastic tarps, allowing for adequate air circulation. Keep away from open flame. Follow good hygienic and
housekeeping practices. Clean-up areas where wood dust settles to avoid excessive accumulation of this combustible
material. Minimize practices that generate airborne dust.
Continued On Next Page
Page 3 of 9 Effective Date: 5/19/2009
PYRO-GUARD® Treated Wood
Section 8. Exposure Controls / Personal Protection
Exposure Guidelines
wood
OF
In AFL
dust tha
HARDWOODS,
Name
CAS#
Agency
Exposure Limits
Comments
Wood Dust
(softwood and
hardwood)
CIO v. OSHA 965 F. 2d
OSHA had established
EXCEPT WESTERN
None
962 (11th Cir. 1992), the
at that time. The 1989 PELs
OSHA
OSHA
ACGIH
ACGIH
Recommended
Recommended
Recommended
court overturned OSHA's
were: TWA 5 mq/m3;
3
PEL-TWA 15 mg/m
(see footnote 1 below)
3
PEL-TWA 5 mg/m
(see footnote 1 below)
TLV-TWA 0.5 mg/m3
TLV-TWA 1 mglm3
PEL-TWA 5 mg/m3
PEL-STEL 10 mg/m3
PEL-TWA 2.5 mg/m3
1989 Air Contaminants
STEL (15 MIN) - 10 ma/m3
Total dust (PNOR)
Respirable dust fraction (PNOR)
Inhaiable, Western red cedar
Inhaiable, All other species
Softwood or hardwood total dust
Softwood or hardwood total dust
Western red cedar total dust
Rule, including the specific PELs for
(ALL SOFTWOODS AND
RED CEDAR): WESTERN RED CEDAR: TWA - 2.5 maim'.
or Inert or Nuisance Dust categories
HAVE INCORPORATED PROVISIONS
Wood dust is now officially regulated as an organic dust under
at PELs noted under the Hazardous Ingredients section of
THE 1989 STANDARD IN THEIR STATE PLANS. ADDITIONALLY,
the Particulates Not Otherwise Regulated (PNOR)
this MSDS. However, A NUMBER OF STATES
OSHA HAS ANNOUNCED THAT IT MAY CITE COMPANIES UNDER THE OSH
ACT GENERAL DUTY CLAUSE UNDER APPROPRIATE CIRCUMSTANCES FOR NON-COMPLIANCE WITH THE 1989 PELs.
Engineering Controls
to keep exposure to airbome contaminants below the exposure limits. Due to the explosive
suspended in air, ventilation systems should be kept clean and precautions should be taken
ignition sources.
Use ventilation as necessary
potential of wood dust when
to prevent sparks or other
Personal Protective Equipment (PPE)
sanding, grinding, routing or chipping wood wear safety glasses with side
grinding, routing or chipping wood, wear clothing that covers the skin -
shoes. When simply handling the product gloves should be worn to protect
sanding, grinding, routing or chipping wood, actions that can generate
after handling and before eating, drinking, or smoking. Launder
reuse.
Eye / Face Protection: When sawing, cutting,
shields.
Skin Protection: When sawing, cutting, sanding,
long pants, long sleeve shirts, hat, gloves and
from splinters.
Respiratory Protection: When sawing, cutting,
wood dust, a dust mask should be worn.
General Hygiene Considerations: Wash thoroughly
clothing worn when generating wood dust before
Continued On Next Page
Page 4 of 9 Effective Date: 5/19/2009
PYRO-GUARD® Treated Wood
Section 9. Physical and Chemical Properties
Appearance: Product appearance and odor is no different than the wood before treatment. Wood species dictates
appearance and odor. Generally a light to dark brown solid. Southern Pine is the predominant species used. Sapwood is
yellowish white and heartwood, reddish brown. Wood dust consists of finely divided particles generated from sawing,
sanding, routing, or chipping solid dimensional lumber or other wood products.
Odor: Wood Smell — Pine Pitch Mainly
Odor Threshold: Not Applicable
Physical State: Solid
pH: Not Applicable
MeltinglFreezing: Not Applicable
Initial Boiling Point and Boiling Range: Not Applicable
Flash Point: Not Applicable
Evaporation Rate: Not Applicable
Upper/Lower Flammability or Explosive Limits: Sawing, sanding or machining wood products can produce wood dust
as a by-product. Wood dust is a strong to severe explosion hazard if a dust cloud contacts an ignition source. 212 F
(100 C) has been suggested as the upper temperature limit for continuous exposure for wood without risk of ignition
(wood dust may require a still lower temperature). An airborne concentration of 40 grams of dust per cubic meter of air is
often used as the lowest explosion limit (LEL) for wood dust.
Vapor Pressure: Not Applicable
Vapor Density: Not Applicable
Specific Gravity or Relative Density: 0.30 to 0.70 Depending On Wood Species (water=1)
Solubility: Insoluble
Partition Coefficient: Not Applicable
Auto -Ignition Temperature: 400° F — 500° F
Decomposition Temperature: > 300° F Char Starts
Section 10. Stability and Reactivity
Chemical Stability: Stable under normal conditions.
Conditions to Avoid: Open flame will cause product to char. Product may ignite at temperature in excess of 400° F. Avoid
prolonged continuous temperature above 212° F.
Incompatible Materials: Strong Acids, Open Flame, and Strong Oxidizers
Hazardous Decomposition Products: Thermal decomposition products include carbon monoxide, carbon dioxide,
aliphatic aldehydes, resin acids, phosphorous compounds, nitrogen compounds, boron compounds, sodium compounds
and polycyclic aromatic hydrocarbons.
Continued On Next Page
Page 5 of 9
Effective Date: 5J19/2009
PYRO-GUARD
Treated Wood
Possibility of Hazardous Reactions: None known.
Section 11. Toxicological Information
No specific toxicological data is available on the fire retardant wood itself. However, considerable information is available
regarding the toxicity of its components and untreated wood. The presence of the fire retardant in the treated wood or
wood dust is not expected to affect its inherent toxicity characteristics.
Carcinogenicity: PYRO-GUARD® Treated Wood and its components are not listed as carcinogens by ACGIH, NIOSH, of
IARC. Wood dust is classified as a carcinogen by ACGIH, NIOSH, and IARC. This classification is based on an increased
incidence of nasal and paranasal cancer in people exposed to wood dusts. Carcinogenicity of wood dust: ACGIH — Al
Confirmed Human Carcinogen (related to wood dusts -hard wood; NIOSH — Occupational carcinogen (related to wood
dust); IARC -- Monograph 62, 1995 (related to wood dust)(Group 1 (carcinogenic to humans)).
Wood Dust:
Wood dust (softwood or hardwood): OSHA Hazard Rating = 3.3; moderately toxic with probable oral lethal dose to
humans being 0.5-5 g/kg (about 1 pound for a 70 kg or 150 pound person). Source: OSHA Regulated Hazardous
Substances, Govemment Institutes, Inc., February 1990.
Carcinogenicity Listing:
EJ NTP: Wood dust, Known Human Carcinogen
IARC Monographs: Wood dust, Group 1
OSHA Regulated: Not listed
NTP: According to its Tenth Report on Carcinogens, NTP states, "Wood dust is known to be a human carcinogen based
on sufficient evidence of carcinogenicity from studies in humans. An association between wood dust exposure and
cancer of the nose has been observed in many case reports, cohort studies, and case -control studies that specifically
addressed nasal cancer. Strong and consistent associations with cancer of the nasal cavities and paranasal sinuses
were observed both in studies of people whose occupations are associated with wood dust exposure and in studies
that directly estimated wood dust exposure."
IARC — Group I: Carcinogenic to humans; sufficient evidence of carcinogenicity. This classification is primarily based on
studies showing an association between occupational exposure to wood dust and adenocarcinoma to the nasal
cavities and paranasal sinuses. IARC did not find sufficient evidence of an association between occupational
exposure to wood dust and cancers of the oropharynx, hypopharynx, lung, lymphatic and hematopoietic systems,
stomach, colon or rectum.
Section 12. Ecological Information
Nitrogen is a critical element for plant growth and a basic constituent of proteins. In excess, however, it can make soil
conditions less favorable for plant growth, damage aquatic life, and impair human health.
Phosphorus is an essential nutrient for plants and animals; however, excessive accumulation of nutrients can represent
too much of a good thing, especially in water bodies such as lakes, streams and estuaries. Loading of nutrients to
surface waters causes changes in ecological function, and often has undesirable environmental and economic
consequences.
Borates have an excellent reputation for safety. In trace amounts, they're essential micronutrients for plants and believed
to be nutritionally important for people. In extreme doses, they can make you ill. As perspective, borates are about as
acutely toxic as table salt. The United States Food and Nutrition Board (FNB) recently recognized the safety of boron by
establishing a Tolerable Upper Intake Level (UL) for boron of 20 milligrams per day.
Eutrophication is the enrichment of freshwater and marine systems with nutrients, particularly nitrogen and phosphorus.
Continued On Next Page
Page 6 of 9
Effective Date: 5/1912009
PYRO-GUARD® Treated Wood
Environmental Toxicity: None known.
Environmental Fate: Wood is a naturally occurring product and decomposes into soil and soil enrichments. The
nitrogen, phosphorus, and boron compounds are plant nutrients and are normal soil additives.
Section 13. Disposal Considerations
Recover or recycle if possible.
Disposal should be in accordance with applicable regional, national and local laws and regulations. Local regulations
may be more stringent than regional or national requirements.
Dispose of as you would any other discarded wooden building component.
If this product as supplied becomes a waste, it does not meet the criteria of a hazardous waste as defined under the
Resource Conservation and Recovery Act (RCRA) 40 CFR 261.
Section 14. Transport Information
Not regulated as a hazardous material by the U.S. Department of Transportation.
Not listed as a hazardous material in Canadian Transportation of Dangerous Goods (TDG).
Section 15. Regulatory Information
US Federal Regulations
All components are on the U.S. EPA TSCA Inventory List or exempt.
None of this product's components are listed under SARA Section 302 (40 CFR 355 Appendix A), or CERCLA (40 CFR
302.4). Tetrachloroisophthalonitrile is listed in SARA Section 313 (40 CFR 372.65)
FIFRA: No information is available.
CERCLA: Not Applicable
OSHA: Wood dust may be hazardous under the criteria of the federal OSHA Hazard Communication standard 29 CFR
1910.1200.
FDA: Not Applicable
State Right -To -Know
This product is not considered hazardous for SARA Title III sections 311/312.
Other state regulations may apply. Check individual state requirements.
Pennsylvania: Wood dust (certain hardwoods as beech and oak) softwood appears on Pennsylvania's Appendix A —
Hazardous Substance Lists.
Continued On Next Page
Page 7 of 9
Ellective Date: 5/19/2009
PYRO-GUARD® Treated Wood
Canada
WHMIS Classification: Wood dust is not considered a controlled product.
DSLINDSL: Not Applicable
Section 16. Other Information
Effective Date: 5/19/2009
Prepared By: Hoover Treated Wood Products, Inc.
User's Responsibility:
Although the information and recommendations set forth herein (hereinafter "Information") are presented in good faith
and believed to be correct as of the date hereof, Hoover Treated Wood Products, Inc. makes no representations as to
the completeness or accuracy thereof. Information is supplied upon the condition that the persons receiving same will
make their own determination as to its suitability for the purposes prior to use. In no event will Hoover Treated Wood
Products, Inc. be responsible for damages or any nature whatsoever resulting from the use of or reliance upon this
information. The user has the responsibility to make sure that this sheet is the most up-to-date issue.
NO REPRESENTATIONS OR WARRANTIES, EITHER EXPRESS OR IMPLIED, OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE OR OF ANY OTHER NATURE ARE MADE HEREUNDER WITH RESPECT TO
INFORMATION OR THE PRODUCT TO WHICH INFORMATION REFERS.
Definition of Common Terms:
ACGIH = American Conference of Governmental Industrial Hygienists
C = Ceiling Limit
CAA = Clean Air Act
CAS# = Chemical Abstracts System Number
CERCLA = Comprehensive Environmental Response, Compensation and Liability Act
CFR = Code of Federal Regulations
CWA = Clean Water Act
DOT = U. S. Department of Transportation
DSL = Domestic Substance List (Canada)
EC50 = Effective concentration that inhibits the endpoint to 50% of control population
EPA = U.S. Environmental Protection Agency
FIFRA = Federal Insecticide, Fungicide and Rodenticide Act
IARC = International Agency for Research on Cancer
IATA = International Air Transport Association
IBC = International Building Code
IDL Ingredient Disclosure List (Canada)
IMDG = International Maritime Dangerous Goods
LC50 = Concentration in air resulting in death to 50% of experimental animals
LCLo = Lowest concentration in air resulting in death
LD50 = Administered dose resulting in death to 50% of experimental animals
LDLo = Lowest dose resulting in death
LEL = Lower Explosive Limit
LFL = Lower Flammable Limit
MSHA = Mining Safety and Health Administration
NAP = Not Applicable
NAV = Not Available
NFPA = National Fire Protection Association
Continued On Next Page
Page 8of9
Effective Date: 5/19/2009
PYRO-GUARD® Treated Wood
NIOSH = National Institute for Occupational Safety and Health
NPRI = Canadian National Pollution Release Inventory
NTP = National Toxicology Program
OSHA = Occupational Safety and Health Administration
PEL = Permissible Exposure Limit
RCRA = Resource Conservation and Recovery Act
SARA = Superfund Authorization and Reauthorization Act
STEL = Short -Term Exposure Limit (15 minutes)
STP = Standard Temperature and Pressure
TCLo = Lowest concentration in air resulting in a toxic effect
TDG = Canadian Transportation of Dangerous Goods
TDLo = Lowest dose resulting in a toxic effect
TLV = Threshold Limit Value
TSCA = Toxic Substance Control Act
TWA = . Time -Weighted Average (8 hours)
UFL = Upper Flammable Limit
WHMIS = Workplace Hazardous Materials Information System (Canada)
Hazard Information Label Text:
FIRE RETARDANT TREATED WOOD DUST
CAUTION!
Sawing, sanding or machining wood products can produce wood dust that can cause a flammable or explosive hazard.
Wood dust may cause lung, upper respiratory tract, eye and skin irritation. Some wood species may cause dermatitis and/or respiratory
allergic effects.
• Avoid dust contact with ignition sources.
• Sweep or vacuum dust for recovery or disposal.
• Avoid prolonged or repeated breathing of wood dust in the air.
• Avoid dust contact with eyes and skin.
• Refer to FIRE RETARDANT TREATED WOOD MSDS for additional information.
FIRST AID: In case of contact, flush eyes or skin with water. If irritation persists, call a physician.
CONTACT: For additional information, please contact the manufacturer.
Last Page Page 9 of 9 Effective Date: 5/19/2009
Revised. August21, 2013
Product:
Synonyms:
0-ON 5Tfr2 uc-�1
FOREST PRODUCTS`
PureBond® Material Data Safety Sheet
pMDI Composite Substrates (Particleboard and MDF)
Supersedes: February 9, 2011 Number at pages: 4
PART I: PRODUCT IDENTIFICATION
Decorative hardwood plywood assembled with pMDI-bonded composite particleboard or
pMDI-bonded medium density fiberboard (MDF) cores in assemblies laminated with
Columbia's proprietary, formaldehyde -free, soy -based PureBond assembly process.
Combination core panel constructions with MDF cross bands beneath the decorative
veneer face and back. Lamination blanks featuring pMDI''bonded mdf crossbands.
PB, MDF, combination panel or combi panel constructions, NAF (No -added formaldehyde)
or NAUF (No -added urea formaldehyde) decorative hardwood plywood.
Trade Names: PureBond brand name when used together with composites can be used together with
these additional, proprietary Columbia sub brand designations: DesignEdge,
DesignEdge+, UV Wood (on PureBond panels), firststep®, LabCoat® (on PureBond
panels), Classic Core®, Classic Lam®
Manufacturer: Columbia Forest Products
7900 Triad Center Drive, Suite 200
Greensboro, NC 27409
www.columbiaforestproducts.com
Contact: Ang Schramm, Technical Services Manager
Emergency phone: 334-616-7745
PART II: HAZARDOUS INGREDIENTS
Component:
Component:
CA Prop 65 Notice:
CAS No.:
Exposure limits:
Methylene-diphenyl-dllsocyanate (pMDt) 2
OSHA PEL — TWA: .02 PPM
ACGIH TLV — T'WA:.005 PPM
WT
<10%
CAS Registry
101-68-8
Wood dust' (Generated as waste by-product of further fabrication by user)
Dulling, sawing, sanding or machining wood products generates wood dust, a substance
known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust
mask or other safeguards for personal protection. Califomia Health and Safety Code
Section 25249.6.
None
ACGIH TLV Softwoods and most hardwoods
(except Beech, and Oak)
ACGIH TLV Certain Hardwoods
(Le. Beech and Oak)
OSHA All soft and hard woods
(except Western Red Cedar)
OSHA Westem Red Cedar
Page 1 of 4
P L STEL
5 mg/mJ TWA 10 mg/m3
(15 min)
1 mg /m3 TWA N/A
5 mg/m3 TWA 10 mg/m3
2.5 mg/m3 TWA N/A
Description:
Specific gravity:
Boiling point:
Solubility in water:
Appearance/Odor:
Flash point:
Autoignition temp.:
Explosive limits in air:
Extinguishing media:
Special fire fighting
procedures:
Unusual fire and
explosion hazard:
Stability:
Incompatibility:
Hazardous
decomposition
products:
Conditions to avoid:
Storage:
PART III: PHYSICAL PROPERTIES
Hardwood veneers, unfinished and flat line UV finished multi -ply composite wood panels
consisting of various combinations of hardwood or decorative veneer faces, bonded to
other wood veneers using adhesives containing no added formaldehyde. Generally used
in cabinets, furnishings, flooring, and in other non-structural applications. Typically
provided as 50"X100" lay -on hardwood veneers, and 4' X 8' hardwood panels. Other
dimensions of hardwood plywood and veneers are available. Thickness of products range
from 1/42" of an inch to over 1".
PART III: PHYSICAL PROPERTIES (Coned)
Usually less than 1, but varies depending on wood species and moisture content.
Not applicable.
Insoluble.
Normal for natural wood. Light to dark in color. Color and odor vary by species and
expired time since processing.
PART IV: FIRE AND EXPLOSION DMA
600° F for wood.
Varies (typically 400° F to 500° F)
N/A for hardwood plywood. 40 g/m3 (LEL) for wood dust.
Water, ammonium phosphate, sand
Follow established procedures for extinguishing wood source fire_
Hardwood plywood does not present an explosion hazard. Sawing, sanding, or
machining of hardwood plywood can produce wood dust as a by-product which
may present an explosion hazard if a dust cloud contacts an ignition source. An
airbome concentration of 40 grams of wood dust per cubic meter of air is often
used as the LEL for wood dust.
PART V: REACTIVITY DATA
Stable under normal conditions.
Avoid contact with strong oxidizing agents and drying oils. Avoid open flame.
Product may ignite at temperatures in excess of 400° F, depending on length
of time of exposure.
Thermal and/or thermal oxidative decomposition of wood can produce irritating
and toxic fumes and gases, including carbon monoxide, hydrogen cyanide,
aldehydes, organic acids, and potynuclear aromatic compounds.
Avoid open flames or other ignition source.
In a coot, dry place, away from ignition sources. Provide adequate ventilation.
Page2d4
CA Prop 65:
Eye contact:
Skin contact:
Ingestion:
Inhalation:
Chronic effects:
Ventilation:
Personal protective
equipment:
Fire prevention:
Eyes:
Skin:
Inhalation:
Ingestion:
PART VI: HEALTH AND HAZARD DATA:
Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection.
Wood dust can cause mechanical irritation.
Wood dust from various species of wood may evoke allergic contact dermatitis in
sensitized individuals.
Not likely to occur.
Wood dust may cause nasal dryness and/or irritation. Coughing, sneezing, wheezing,
sinusitis, prolonged colds, and headaches have also been reported. May aggravate
preexisting respiratory conditions or allergies. Wood dust may cause nasal obstruction.
Depending on species, wood dust may cause dermatitis on prolonged, repetitive
contact. Wood dust may cause respiratory sensitization and/or irritation. Pre-existing
respiratory disorders may be aggravated by exposure.
Prolonged exposure to wood dust has been reported by some observers of European
furniture workers to be associated with nasal cancer. IARC classifies wood dust as a
carcinogen to humans (Group 1). This classification is based primarily on the 1ARC's
evaluation of increased risk in the occurrence of adenocarcinomas of the nasal cavities
and paranasal sinuses associated with exposure to wood dust. IARC did not find sufficient
evidence to associate cancers of the oropharynx, lung, lymphatic, and hematopietic
systems, stomach, colon, or rectum with exposure to wood dust. The National Toxicology
Program (NTP) has also listed wood dust as a known human carcinogen. Wood dust is not
listed as a carcinogen by ACGIH or OSHA. A large case control nasal cancer mortality
study in North Carolina, Mississippi, Washington and Oregon (1962-1977) did not
demonstrate an association between nasal cancer and occupations normally associated
with wood dust.
PART VII: PRECAUTIONS AND SAFE HANDLING
Provide adequate ventilation and exhaust to keep airborne wood dust contaminant
concentration levels below the OSHA PEL
Wear goggles or safety glasses when manufacturing or machining any wood
product. Wear NIOSH/MSHA approved respirator when the allowable limits
may be exceeded. Other protective equipment, such as gloves and outer
garments may be needed, depending on wood dust conditions.
Avoid open flames or other ignition sources. Keep type A or ABC fire extinguisher readily
available.
PART VIII: EMERGENCY AND FIRST AID PROCEDURES
Flush with large amounts of water. Remove to fresh air. If irritation persists,
seek medical attention.
Wash affected area with soap and water. If rash, persistent irritation, or
dermatitis occurs, seek medical attention.
Remove to fresh air. Get medical advice if persistent irritation, severe coughing,
or breathing difficulty occurs.
Not applicable.
PART IX: SPILL, LEAK, STORAGE, AND DISPOSAL
Pick up, vacuum, or sweep spills for recovery and/or disposal. Avoid creating dusty conditions. Provide good
ventilation where dust conditions cannot be avoided during cleanup. Place recovered wood dust in a container for
Page3d4
proper disposal. Dispose in accordance with Federal, State, and Local regulations. Disposal is the responsibility of
the generator.
PART X: KEY TO COMMONLY USED ACRONYMS
ACGIH: American Conference of Government and Industrial Hygienists
CARB California Air Resources Board
HUD: US Department of Housing and Urban Development
IARC: International Agency for Research on Cancer
LEED: Leadership in Energy and Environmental Design (LEED) Green Building Rating Syste
LEL: Lowest explosion limit
Mg/m3: Milligrams per cubic meter
MSDS: Material Safety Data Sheet
NTP: National Toxicology Program
OSHA: Occupational Safety and Health Administration
PEL: Permissible exposure limit
PPM: Parts per million
STEL: Short term exposure limit
TLV: Threshold limit value
TWA: Time weighted average
USGBC: United States Green Building Council
PART XI: USER RESPONSIBILITY
Important: This information is offered in good faith. It is believed to be accurate and has been compiled from
sources believed to be reliable. It is offered for your consideration, investigation, and verification. Columbia Forest
Products makes no warranty of any kind, expressed or implied, concerning the accuracy or completeness of the
information and data herein. Furthermore, Columbia Forest Products will not be liable for claims relating to any
party's use of, or reliance on information and data contained herein, regardless of whether it is claimed that the
information and data are inaccurate, incomplete, or otherwise misleading.
It is the responsibility of the user to comply with local, state, and/or federal regulations concerning the storage, use,
processing, and disposal of the product or subsequently generated waste. It is the responsibility of the user to
ensure that this MSDS is the most current version.
FOOTNOTES
1. in AFL-CIO v. OSHA 965 F. 2d 962 (11th Cir. 1992), the court overtumed OSHA's 1989 Air Contaminants Rule,
including the specific PELs for wood dust that OSHA had established at that time. The 1989 PELs were: TWA - 5
mo/m3. STEL (15 min.) - 10.0 mo(m3 (all soft and hard woods except Western red cedar): Westem red cedar TWA-2.5
ma/m3'
Wood dust is now officially regulated as an organic dust under the Particulates Not Otherwise Regulated (PNOR) or
Inert or Nuisance Dust categories at PELs noted under PART II of this MSDS. However, a number of states have
incorporated provisions of the 1989 standard in their state plans. Additionally, OSHA has announced that it may cite
companies under the OSH Act General Duty Clause under appropriate circumstances for non-compliance with the
1989 PELs,
Py4of4
\yvVL-'
5
FOREST PRODUCTS`
PureBond° Material Data Safety Sheet
Domestic Veneer Core Constructions
Revised: August 21, 2013
Product:
Supersedes: February 9. 2011 Number of pages: 4
PART I: PRODUCT IDENTIFICATION
Decorative hardwood plywood assembled with domestic veneer core in assemblies
laminated with Columbia's proprietary, formaldehyde -free, soy -based PureBond assembly
process.
Domestic aspen/poplar veneer core lamination blanks and bending plywood without
decorative hardwood face and back veneers laminated with Columbia's proprietary,
formaldehyde -free, soy -based PureBond assembly process. Decorative rotary veneer also
covered by this document.
Synonyms: NAF (No -added formaldehyde) or NAUF (No -added urea formaldehyde) decorative
hardwood plywood
Trade Names: PureBond brand name can be used together with these additional, proprietary Columbia
sub brand designations: JayCore®, KayCore, CANAM Gold/silver, DesignEdge,
DesignEdge+, MPX®, UV Wood (on PureBond panels), firststep®, LabCoat® (on
PureBond panels.)
Manufacturer. Columbia Forest Products
7900 Triad Center Drive, Suite 200
Greensboro, NC 27409
www.columbiaforestproducts.com
Contact: Ang Schramm, Technical Services Manager
Emergency phone: 334-616-7745
Component:
CA Prop 65 Notice:
CAS No.:
Exposure limits:
PART II: HAZARDOUS INGREDIENTS
Wood dust' (Generated as waste by-product of further fabrication by user)
Drilling, sawing, sanding or machining wood products generates wood dust, a substance
known to the State of California to cause cancer. Avoid inhaling wood dust or use a dust
mask or other safeguards for personal protection. Califomia Health and Safety Code
Section 25249.6,
None
ACGIH TLV Softwoods and most hardwoods
(except Beech, and Oak)
ACGIH TLV Certain Hardwoods
(i.e. Beech and Oak)
OSHA All soft and hard woods
(except Westem Red Cedar)
OSHA Westem Red Cedar
Page 1 cf 4
PEL STEL
5 mglm TWA 10 mg/m3
(15 min)
1 mg /m3 TWA N/A
5 mg/m3 TWA 10 mg/m3
2.5 mg/m3 TWA N/A
Description:
Specific gravity:
Boiling point:
Solubility in water:
Appearance/Odor:
Flash point:
Autoignition temp.:
Explosive limits in air:
Extinguishing media:
Special fire fighting
procedures:
Unusual fire and
explosion hazard:
Stability:
Incompatibility:
Hazardous
decomposition
products:
Conditions to avoid:
Storage:
FOREST PRODUCTS"
PART III: PHYSICAL PROPERTIES
Hardwood veneers, unfinished and flat line W finished multi -ply composite wood panels
consisting of various combinations of hardwood or decorative veneer faces, bonded to
other wood veneers using adhesives containing no added formaldehyde. Generally used
in cabinets, furnishings, flooring, and in other non-structural applications. Typically
provided as 50"X100" lay -on hardwood veneers, and 4' X 8' hardwood panels. Other
dimensions of hardwood plywood and veneers are available. Thickness of products range
from 1/42" of an inch to over 1".
PART III: PHYSICAL PROPERTIES (Cont'dl
Usually less than 1, but varies depending on wood species and moisture content.
Not applicable.
Insoluble.
Normal for natural wood. Light to dark in color. Color and odor vary by species and
expired time since processing.
PART IV: FIRE AND EXPLOSION DATA
600° F for wood.
Varies (typically 400° F to 500° F)
N/A for hardwood plywood. 40 g/m3 (LEL) for wood dust.
Water, ammonium phosphate, sand
Follow established procedures for extinguishing wood source fire.
Hardwood plywood does not present an explosion hazard. Sawing, sanding, or
machining of hardwood plywood can produce wood dust as a by-product which
may present an explosion hazard if a dust cloud contacts an ignition source. An
airbome concentration of 40 grams of wood dust per cubic meter of air is often
used as the LEL for wood dust.
PART V: REACTIVITY DATA
Stable under normal conditions.
Avoid contact with strong oxidizing agents and drying oils. Avoid open flame.
Product may ignite at temperatures in excess of 400° F, depending on length
of time of exposure.
Thermal and/or thermal oxidative decomposition of wood can produce irritating
and toxic fumes and gases, including carbon monoxide, hydrogen cyanide,
aldehydes, organic adds, and potynuclear aromatic compounds.
Avoid open flames or other ignition source.
In a cool, dry place, away from ignition sources. Provide adequate ventilation.
Page 2d4
CA Prop 65:
Eye contact:
Skin contact:
Ingestion:
Inhalation:
Chronic effects:
Ventilation:
Personal protective
equipment:
Fire prevention:
Eyes:
Skin:
Inhalation:
Ingestion:
FOREST PRODUCTS`
PART VI: HEALTH AND HAZARD DATA:
Avoid inhaling wood dust or use a dust mask or other safeguards for personal protection.
Wood dust can cause mechanical irritation.
Wood dust from various species of wood may evoke allergic contact dermatitis in
sensitized individuals.
Not likely to occur.
Wood dust may cause nasal dryness and/or irritation. Coughing, sneezing, wheezing,
sinusitis, prolonged colds, and headaches have also been reported. May aggravate
preexisting respiratory conditions or allergies. Wood dust may cause nasal obstruction.
Depending on species, wood dust may cause dermatitis on prolonged, repetitive
contact. Wood dust may cause respiratory sensitization and/or irritation. Pre-existing
respiratory disorders may be aggravated by exposure.
Prolonged exposure to wood dust has been reported by some observers of European
fumiture workers to be associated with nasal cancer. IARC classifies wood dust as a
carcinogen to humans (Group 1). This classification is based primarily on the IARC's
evaluation of increased risk in the occurrence of adenocarcinomas of the nasal cavities
and paranasal sinuses associated with exposure to wood dust. IARC did not find sufficient
evidence to associate cancers of the oropharynx, Lung, lymphatic, and hematopietic
systems, stomach, colon, or rectum with exposure to wood dust. The National Toxicology
Program (NTP) has also listed wood dust as a known human carcinogen. Wood dust is not
listed as a carcinogen by ACGIH or OSHA. A large case control nasal cancer mortality
study in North Carolina, Mississippi, Washington and Oregon (1962-1977) did not
demonstrate an association between nasal cancer and occupations normally associated
with wood dust.
PART VII: PRECAUTIONS AND SAFE HANDLING
Provide adequate ventilation and exhaust to keep airborne wood dust contaminant
concentration levels below the OSHA PEL
Wear goggles or safety glasses when manufacturing or machining any wood
product. Wear NIOSH/MSHA approved respirator when the allowable limits
may be exceeded. Other protective equipment, such as gloves and outer
garments may be needed, depending on wood dust conditions.
Avoid open flames or other ignition sources. Keep type A or ABC fire extinguisher readily
available.
PART VIII: EMERGENCY AND FIRST AID PROCEDURES
Flush with large amounts of water. Remove to fresh air. If irritation persists,
seek medical attention.
Wash affected area with soap and water. If rash, persistent irritation, or
dermatitis occurs, seek medical attention.
Remove to fresh air. Get medical advice if persistent irritation, severe coughing,
or breathing difficulty occurs.
Not applicable.
Page 3 of 4
columbia
FOREST PRODUCTS`
PART IX: SPILL, LEAK, STORAGE, AND DISPOSAL
Pick up, vacuum, or sweep spills for recovery and/or disposal. Avoid creating dusty conditions. Provide good
ventilation where dust conditions cannot be avoided during cleanup. Place recovered wood dust in a container for
proper disposal, Dispose in accordance with Federal, State, and Local regulations. Disposal is the responsibility of
the generator.
PART X: KEY TO COMMONLY USED ACRONYMS
ACGIH: American Conference of Govemment and Industrial Hygienists
CARB Califomia Air Resources Board
HUD: US Department of Housing and Urban Development
IARC: International Agency for Research on Cancer
LEED: Leadership in Energy and Environmental Design (LEED) Green Building Rating System
LEL: Lowest explosion limit
Mg/ma: Milligrams per cubic meter
MSDS: Material Safety Data Sheet
NTP: National Toxicology Program
OSHA: Occupational Safety and Health Administration
PEL: Permissible exposure limit
PPM: Parts per million
STEL: Short term exposure limit
TLV: Threshold limit value
TWA: Time weighted average
USGBC: United States Green Building Council
PART XI: USER RESPONSIBILITY
Important: This information is offered in good faith. It is believed to be accurate and has been compiled from
sources believed to be reliable. It is offered for your consideration, investigation, and verification. Columbia Forest
Products makes no warranty of any kind, expressed or implied, concerning the accuracy or completeness of the
information and data herein. Furthermore, Columbia Forest Products will not be liable for claims relating to any
party's use of, or reliance on information and data contained herein, regardless of whether it is claimed that the
information and data are inaccurate, incomplete, or otherwise misleading.
It is the responsibility of the user to comply with local, state, and/or federal regulations concerning the storage, use,
processing, and disposal of the product or subsequently generated waste. It is the responsibility of the user to
ensure that this MSDS is the most current version.
FOOTNOTES
1. In AFL-CIO v. OSHA 965 F. 2d 962 (11th Cir, 1992), the court overtumed OSHA's 1989 Air Contaminants Rule,
including the specific PELs for wood dust that OSHA had established at that time. The 1989 PELs were: TWA - 5
rna/m3: STEL (15 min.) - 10,0 mg/m3 (all soft and hard woods except Western red cedar) Westem red cedar TWA-2.5
maim.
Wood dust is now officially regulated as an organic dust under the Particulates Not Otherwise Regulated (PNOR) or
Inert or Nuisance Dust categories at PELs noted under PART 11 of this MSDS. However a number of states have
incorporated provisions of the 1989 standard in their state plans. Additionally, OSHA has _announced that it may cite
companies under the OSH Act General Duty Clause under appropriate circumstances for non-compliance with the
1989 PELs.
2. This inoredieot is the polymerized Lcuredl forimoLMD1 resin in the raw comnos+te panels used by Columbia for the
production of Pure8ond assemblies. There is no detectable MDI monomer in the product as purchased.
Page 4 of 4
FOREST PRODUCTS'
tIS
�t NSTe_vc-vi �sJ
Added Urea and Phenol Formaldehyde Panels
MATERIAL SAFETY DATA SHEET
Revised: August 22, 2013
Products:
Synonyms:
Trade Names:
Manufacturer:
Component:
CAS No.:
Exposure limits:
Component:
CAS No.:
Exposure limits:
Supersedes: July 16, 2013 Number of pages. 4
PART I: PRODUCT IDENTIFICATION
Domestic and imported urea -formaldehyde (UF), scavenged urea -formaldehyde
(ULEF) or phenol formaldehyde (PF) bonded substrates with soy based decorative
veneer lamination technology in unfinished or UV (clear, prime, pigment) coated
hardwood industrial stock panels with veneer, particleboard or MDF cores, melamine
on particleboard, engineered veneer, bark mulch, wood chips
Hardwood plywood, prefinished plywood, melamine, Russian birch, Baltic birch, bark
dust
Europty Plus®, CFP 60"s®
Columbia Forest Products
Corporate Office
7900 Triad Center Drive, Suite 200
Greensboro, NC 27409
1-800-637-1609
www.columbiaforestproducts.com
Contact: Ang Schramm, Tech Services Mngr.
Emergency Phone: 334-616-7745
PART II: HAZARDOUS INGREDIENTS
Wood dust' (Generated as waste by-product of further
None
ACGIH TLV Softwoods and most hardwoods
(except Beech, and Oak)
ACGIH TLV Certain Hardwoods
(i.e. Beech and Oak)
OSHA All soft and hard woods
(except Westem Red Cedar)
OSHA Western Red Cedar
fabrication by user)
PEL STEL
5 mg/m TWA 10 mg/m3
(15 min)
1 mg /m3 TWA N/A
5 mg/m3 TWA 10 mg/m3
2.5 mglm3 TWA N/A
Formaldehyde gas (emitted in small and diminishing quantities from Urea
Formaldehyde resin glue. Phenolic formaldehyde adhesive systems not regulated)
50-00-0
OSHA
ACGIH TLV
HUD
0.75 ppm TWA 2 ppm
0.3 ppm Ceiling
0.3 ppm @ .13 ft2/ft3
Formaldehyde gas emissions
from industrial stock panels
tested under prescribed
conditions for manufactured
housing applications.
Description:
Specific gravity:
Boiling point:
Solubility in water:
Appearance/Odor:
Flash point:
Autoignition temp.:
Explosive limits in air:
Extinguishing media:
Special fire fighting
procedures:
Unusual fire and
explosion hazard:
Stability:
Incompatibility:
Hazardous decom-
position products:
Conditions to avoid:
Storage:
Hazardous poly-
merization:
Eye contact:
Skin contact:
Ingestion:
Inhalation:
PART III: PHYSICAL PROPERTIES
Unfinished and UV Finished multi -ply composite wood panels consisting of various
combinations of hardwood or decorative veneer faces, bonded to other wood veneers,
particleboard, medium density fiberboard, lumber, or hardboard. Generally used in
cabinets, fumishings, laminated block flooring, and in other non-structural applications.
Typically provided as 4' X 8' panels, but available in other sizes. Thicknesses range
from under 1/8" to over 1".
Usually less than 1, but varies depending on wood species and moisture content.
Not applicable.
Insoluble.
Normal for natural wood. Light to dark in color. Color and odor vary by species
and expired time since processing.
PART IV: FIRE AND EXPLOSION DATA
600° F for wood.
Varies (typically 400° F to 500° F)
N/A for hardwood plywood. 40 g/m3 (LEL) for wood dust.
Water, carbon dioxide, sand
Follow established procedures for extinguishing wood source fire.
Hardwood plywood does not present an explosion hazard. Sawing, sanding, or
machining of hardwood plywood can produce wood dust as a by-product which
may present an explosion hazard if a dust cloud contacts an ignition source. An
airborne concentration of 40 grams of wood dust per cubic meter of air is often
used as the LEL for wood dust.
PART V: REACTIVITY DATA
Stable under normal conditions.
Avoid contact with strong oxidizing agents and drying oils. Avoid open flame.
Product may ignite at temperatures in excess of 400° F, depending on length
of time of exposure.
Thermal and/or thermal oxidative decomposition of wood can produce irritating
and toxic fumes and gases, including carbon monoxide, hydrogen cyanide,
aldehydes, organic acids, and polynuclear aromatic compounds.
High temperatures and high relative humidity increase the rate of formaldehyde
emissions. Avoid open flames or other ignition source.
In a cool, dry place, away from ignition sources. Provide adequate ventilation.
Not applicable.
PART VI: HEALTH AND HAZARD DATA:
Gaseous formaldehyde may cause temporary irritation or a burning sensation.
Wood dust can cause mechanical irritation.
Both formaldehyde and wood dust from various species of wood may evoke
allergic contact dermatitis in sensitized individuals.
Not likely to occur.
Wood dust and/or formaldehyde may cause nasal dryness and/or irritation.
2
Chronic effects:
Ventilation:
Personal protective
equipment:
Fire prevention:
Coughing, sneezing, wheezing, sinusitis, prolonged colds, and headaches have
also been reported. Both may aggravate preexisting respiratory conditions or
allergies. Wood dust may also cause nasal obstruction.
Depending on species, wood dust may cause dermatitis on prolonged, repetitive
contact. Formaldehyde and/or wood dust may cause respiratory sensitization and/or
irritation. Pre-existing respiratory disorders may be aggravated by exposure.
Prolonged exposure to wood dust has been reported by some observers of European
fumiture workers to be associated with nasal cancer. IARC classifies wood dust as a
carcinogen to humans (Group 1). This classification is based primarily on IARC's
evaluation of increased risk in the occurrence of adenocarcinomas of the nasal cavities
and paranasal sinuses associated with exposure to wood dust. IARC did not find
sufficient evidence to associate cancers of the oropharyrix, lung, lymphatic, and
hematopietic systems, stomach, colon, or rectum with exposure to wood dust. The
National Toxicology Program (NTP) has also listed wood dust as a known human
carcinogen. Wood dust is not listed as a carcinogen by ACGIH or OSHA. A large case
control nasal cancer mortality study in North Carolina, Mississippi, Washington and
Oregon (1962-1977) did not demonstrate an association between nasal cancer and
occupations normally associated with wood dust.
Formaldehyde is listed by IARC as a human carcinogen. NTP includes formaldehyde
in the Annual Report on Carcinogens. Formaldehyde is regulated by OSHA as a
potential cancer agent. Some rats exposed under laboratory conditions to 14 ppm
formaldehyde (a level far exceeding human tolerance limits, and far exceeding that
normally found in the workplace) for two years developed a nasal cancer. The
Universities Associated for Research and Education in Pathology (UAREP) has stated
in a report Epidemiology of a Chronic Occupational Exposure to Formaldehyde,
(December, 1987,) that: `1: For no malignancy in man is there convincing evidence of
a relationship with formaldehyde exposure; and 2: Furthermore, that if a relationship
does exist, the excess risk, in absolute terms, must be small.'
PART VII: PRECAUTIONS AND SAFE HANDLING
Provide adequate ventilation and exhaust to keep airborne contaminant
concentration levels below the OSHA PELs, and to reduce the possible buildup
of formaldehyde gas, particularly when high temperatures and relative humidity
occur. Avoid dusty conditions, and observe same ventilation for wood dust as
indicated for formaldehyde.
Wear goggles or safety glasses when manufacturing or machining any wood
product. Wear NIOSH/MSHA approved respirator when the allowable limits
may be exceeded. Other protective equipment, such as gloves and outer
garments may be needed, depending on dust conditions.
Avoid open flames or other ignition sources. Keep fire extinguisher readily
available.
PART VIII: EMERGENCY AND FIRST AID PROCEDURES
Eyes: Flush with large amounts of water. Remove to fresh air. If irritation persists,
seek medical attention.
Skin: Wash affected area with soap and water. If rash, persistent irritation, or
dermatitis occurs, seek medical attention.
Inhalation: Remove to fresh air. Get medical advice if persistent irritation, severe coughing,
or breathing difficulty occurs.
Ingestion: Not applicable.
3
PART IX: SPILL, LEAK, STORAGE, AND DISPOSAL
Pick up, vacuum, or sweep spills for recovery and/or disposal. Avoid creating dusty conditions. Provide good
ventilation where dust conditions cannot be avoided during cleanup. Place recovered wood dust in a container
for proper disposal. Store in well ventilated area as product will emit small amounts of formaldehyde. Dispose
in accordance with Federal, State, and Local regulations. Disposal is the responsibility of the generator.
PART X: KEY TO COMMONLY USED ACRONYMS
ACGIH: American Conference of Government and Industrial Hygienists
EPA: Environmental Protection Agency
HUD: US Department of Housing and Urban Development
IARC: International Agency for Research on Cancer
LEL: Lowest explosion limit
Mg/m3: Milligrams per cubic meter
MSDS: Material Safety Data Sheet
NTP: National Toxicology Program
OSHA: Occupational Safety and Health Administration
PEL: Permissible exposure limit
PPM: Parts per million
STEL: Short term exposure limit
TLV: Threshold limit value
TWA: Time weighted average
PART XI: USER RESPONSIBILITY
Important: This information is offered in good faith. It is believed to be accurate and has been compiled from
sources believed to be reliable. It is offered for your consideration, investigation, and verification. Columbia
Forest Products makes no warranty of any kind, expressed or implied, concerning the accuracy or
completeness of the information and data herein. Furthermore, Columbia Forest Products will not be liable for
claims relating to any party's use of, or reliance on information and data contained herein, regardless of whether
it is claimed that the information and data are inaccurate, incomplete, or otherwise misleading.
It is the responsibility of the user to comply with local, state, and/or federal regulations concerning the storage,
use, processing, and disposal of the product or subsequently generated waste. It is the responsibility of the
user to ensure that this MSDS is the most current version.
IMPORTANT FOOTNOTE
CONCERNING OSHA PELS FOR WOOD DUST
In AFL-CIO v. OSHA 965 F. 2d 962 (11th Cir. 1992), the court overtumed OSHA's 1989 Air Contaminants Rule, including the
specific PELs for wood dust that OSHA had established at that time. The 1989 PELs were: TWA - 5 u.W 3: STE.. (15 min, j
- 10.0 mo/m3 Call soft and hard woods except Westem red cedar); Westem red cedar TWA-2.5 mile.
Wood dust is now officially regulated as an organic dust under the Particulates Not Otherwise Regulated (PNOR) or Inert or
Nuisance Dust categories at PELs noted under PART II of this MSDS. However, a number of states have incorporated
provisions of the 1989 standard in their state plans. Additionally, OSHA has announced that it may cite companies under the
OSH Act General Duty Clause under aoorooriate circumstances for non-compliance with the 1989 PELS,
4
valspar
if it matters, we're on it:
Material Safety Data Sheet
PRODUCT AND COMPANY IDENTIFICATION
Product Identification
Product ID:
Product Name:
Product Use:
Print date:
Revision Date:
NAW1322
LUSTER LAC PREM W LAC 275
Paint product.
25/May/2013
25/May/2013
Company Identification
The Valspar Corporation
PO Box 1461
Minneapolis, MN 55440
Manufacturer's Phone: 1-612-851-7000
24-Hour Medical Emergency 1-888-345-5732
Phone:
2. HAZARDS IDENTIFICATION
Primary Routes of Exposure:
Inhalation
ingestion
Skin absorption
Eye Contact:
• Severe eye irritation
Skin Contact:
• Causes skin irritation.
• May cause defatting of the skin.
• Harmful if absorbed through skin.
Ingestion:
• Irritation of the mouth, throat, and stomach.
• Harmful if swallowed.
• Aspiration hazard if swallowed - can enter lungs and cause damage.
Product ID: NAW1322
Page 1 / 8
Inhalation:
• Causes respiratory tract irritation.
• Harmful by inhalation
Target Organ and Other Health Effects:
• Causes headache, drowsiness or other effects to the central nervous system.
• Contains glycol ether which has been shown to cause blood effects damage in laboratory animals.
• Kidney injury may occur.
• Liver injury may occur.
• Spleen damage may occur.
• Blood disorders
This product contains ingredients that may contribute to the following potential chronic health effects:
• Notice: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain
and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be
harmful or fatal.
• Prolonged exposure over TLV may produce pneumoconiosis.
Carcinogens:
• Possible cancer hazard. Contains material which may cause cancer based on animal data.
3. COMPOSITION / INFORMATION ON HAZARDOUS INGREDIENTS
ingredient Name
CAS -No.
DIMETHYL KETONE -
`EXEMPT SOLVENT
67-64-1
TITANIUM DIOXIDE
13463-67-7
Approx.
Weight %
50-55
5-10
Chemical Name
Acetone
Titanium dioxide
PROPRIETARY RESIN
5-10
PROPRIETARY RESIN
ETHYLENE GLYCOL
MONOBUTYL ETHER
111-76-2
5-10
2-Butoxyethanol
PROPRIETARY INERT
5-10
PROPRIETARY INERT
BUTYL ACETATE
123-86-4
1-5
n-Butyl acetate
PROPRIETARY ADDITIVE 1 - 5
PROPRIETARY ADDITIVE
If this section is blank there are no hazardous components per OSHA guidelines.
4. FIRST AID MEASURES
Eye Contact:
In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. If easy to do, remove contact
lenses. If medical assistance is not immediately available, flush an additional 15 minutes. Get medical attention
immediately.
Skin Contact:
Remove contaminated clothing and shoes Wash off immediately with plenty of water for at least 15 minutes. Get medical
attention, if symptoms develop or persist.
Product ID: NAW1322
Page 2 / 8
Ingestion:
Rinse mouth with water. Give one or two glasses of water. Only induce vomiting at the instruction of medical personnel,
Never give anything by mouth to an unconscious person. Do NOT induce vomiting. If vomiting occurs, keep head lower
than hips to prevent aspiration. Get medical attention immediately.
Inhalation:
Move injured person into fresh air and keep person calm under observation. Get medical attention immediately.
Medical conditions aggravated by exposure:
Any respiratory or skin condition.
5. FIRE FIGHTING MEASURES
Flash point (Fahrenheit): 1
Flash point (Celsius): -17
Lower explosive limit (%): 1
Upper explosive limit (%): 13
Autoignition temperature: not determined
Sensitivity to impact: no
Sensitivity to static discharge: Subject to static discharge hazards. Please see bonding
and grounding information in Section 7.
Hazardous combustion products: See Section 10.
Unusual fire and explosion hazards:
None known.
Extinguishing media:
Carbon dioxide, dry chemical, foam and/or water fog.
Fire fighting procedures:
Firefighters should be equipped with self-contained breathing apparatus and turn out gear. Keep containers and
surroundings cool with water spray.
6. ACCIDENTAL RELEASE MEASURES
Action to be taken if material is released or spilled:
Ventilate the area. Avoid breathing dust or vapor. Use self -containing breathing apparatus or airmask for large spills in a
confined area. Wipe, scrape or soak up in an inert material and put in a container for disposal. See section 7, "Handling
and Storage", for proper container and storage procedures. Remove all sources of ignition. Soak up with inert absorbent
material. Use only non -sparking tools. Avoid contact with eyes.
7. HANDLING AND STORAGE
Precautions to be taken in handling and storage:
Keep away from heat, sparks and open flame. - No smoking. Keep container closed when not in use. Do not store above
120 degrees F, (49 degrees C). Based on flash point and vapor pressure, suitable storage should be provided in
accordance with OSHA regulation 1910.106, Ontario OH&S regulation 851 section 22. Empty containers may contain
product residue, including flammable or explosive vapors. Do not cut, puncture or weld on or near container. All label
warnings must be observed until the container has been commercially cleaned or reconditioned. If the product is used
near or above the flashpoint, an ignition hazard may be present. Activities, uses, or operations which liberate vapor (such
as mixing or free fall of liquids) may also present an ignition hazard. Please ensure containers and other interconnected
equipment are properly bonded and grounded at all times.
8. PERSONAL PROTECTIVE EQUIPMENT AND EXPOSURE CONTROLS
Personal Protective Equipment
Product 10: NAW1322
Page 3 / 8
Eye and face protection:
Wear safety glasses or goggles to protect against exposure.
Skin protection:
Appropriate chemical resistant gloves should be worn.
Other Personel Protection Data:
To prevent skin contact wear protective clothing covering all exposed areas.
Respiratory protection:
If exposure cannot be controlled below applicable limits, use the appropriate NIOSH approved respirator such as an air
purifying respirator with organic vapor cartridge and dust/mist filter. Consult the respirator manufacturer's literature to
ensure that the respirator will provide adequate protection. Read and follow all respirator manufacturer's instructions.
Ventilation
Use only in well -ventilated areas. Ensure adequate ventilation, especially in confined areas. Ovens used for curing should
contain a fresh air purge to prevent vapours from accumulating and creating a possible explosive mixture. Where the
product is used in a hazardous classified area, use explosion -proof electrical/ventilating/lighting/equipment.
Exposure Guidelines
OSHA Perrnissible Exposure Limits (PEL's)
Ingredient Name
CAS -No.
Approx.
Weight %
TWA (final)
Ceilings limits (final)
Skin designations
DIMETHYL KETONE-
EXEMPT SOLVENT
67-64-1
50 - 55
1000 ppm TWA
2400 mg/m3 TWA
TITANIUM DIOXIDE
13463-67-7
5 - 10
15 mg/m3 TWA dust
total
ETHYLENE GLYCOL
MONOBUTYL ETHER
111-76-2
5 - 10
240 mg/m3 TWA
50 ppm TWA
prevent or reduce skin
absorption
PROPRIETARY INERT
5 - 10
Respirable. Listed.
Total dust. Listed.
BUTYL ACETATE
123-86-4
1 - 5
150 ppm TWA
710 mglm3 TWA
ACGIH Threshold Limit Value (TLV's)
Ingredient Name
CAS -No.
Approx.
Weight %
TWA
STEL
Ceiling limits
Skin
designations
DIMETHYL KETONE-
EXEMPT SOLVENT
67-64-1
50 - 55
500 ppm TWA
750 ppm STEL
TITANIUM DIOXIDE
13463-67-7
5 - 10
10 mg/m3 TWA
ETHYLENE GLYCOL
MONOBUTYL ETHER
111-76-2
5 -10
20 ppm TWA
PROPRIETARY INERT
5 - 10
2 mg/m3 TWA
particulate matter
containing no
asbestos and <1
crystalline silica,
respirable fraction
BUTYL ACETATE
123-86-4
1 - 5
150 ppm TWA
200 ppm STEL
Product ID: NAW 1322
Page 4 / 8
9. PHYSICAL PROPERTIES
Odor:
Physical State.
pH:
Vapor pressure:
Vapor density (air = 1.0):
Boiling point:
Solubility in water:
Coefficient of water/oil distribution:
Density (Ibs per US gallon):
Specific Gravity:
Evaporation rate (butyl acetate = 1.0):
Flash point (Fahrenheit):
Flash point (Celsius):
Lower explosive limit (%):
Upper explosive limit (%):
Autoignition temperature:
10, STABILITY AND REACTIVITY
Stability:
Conditions to Avoid:
Incompatibility:
Hazardous Polymerization:
Hazardous Decomposition Products:
Sensitivity to static discharge:
11. TOXICOLOGICAL INFORMATION
Normal for this product type.
liquid
not determined
175.1879699 mmHg @ 68°F (20°C)
4.1
132.89°F (56°C)
not determined
not determined
8.47
1.02
5.6
1
-17
1
13
not determined
Stable under normal conditions.
Heat.
Strong oxidizing agents
None anticipated.
Silicon dioxide. Carbon monoxide and carbon dioxide.
Metal oxide fumes. Nitrogen compounds.
Subject to static discharge hazards. Please see bonding
and grounding information in Section 7.
Ingredient Name
CAS -No.
Approx.
Weight %
NIOSH - Selected LD50s and LC5Os
DIMETHYL KETONE-
EXEMPT SOLVENT
67-64-1
50 - 55
= 5800 mg/kg Oral L050 Rat
TITANIUM DIOXIDE
13463-67-7
5 - 10
> 10000 mg/kg Oral LD50 Rat
PROPRIETARY RESIN
5 - 10
> 5 g/kg Oral LD50 Rat
ETHYLENE GLYCOL
MONOBUTYL ETHER
111-76-2
5 - 10
= 2.21 mg/L Inhalation LC50 Rat 4 h
= 220 mg/kg Dermal LD50 Rabbit
= 2270 mg/kg Dermal LD50 Rat
= 450 ppm Inhalation LC50 Rat 4 h
= 470 mg/kg Oral LD50 Rat
BUTYL ACETATE
123-86.4
1 - 5
= 10768 mg/kg Oral LD50 Rat
= 390 ppm Inhalation LC50 Rat 4 h
> 17600 mg/kg Dermal LD50 Rabbit
Mutagens(Teratogens/Carcinogens:
Possible cancer hazard. Contains material which may cause cancer based on animal data.
Product ID: NAW1322
Page 5 / 8
Contains T102 which is listed by IARC as a possible human carcinogen (Group 2B) based on animal data. Neither long
term animal studies, nor human epidemiology studies of workers exposed to TIO2 provide an adequate basis to conclude
T102 is carcinogenic. T1O2 is not classified as a carcinogen by NTP, U.S. OSHA, or the U.S. EPA.
Ingredient Name
CAS -No.
Approx.
Weight %
IARC Group 1 - Human
Evidence
IARC Group 2A - Limited
Human Data
IARC Group 2B -
Sufficient Animal Data
TITANIUM DIOXIDE
13463-67-7
5 - 10
Monograph 47 (1989)
Ingredient Name
CAS -No.
Approx.
Weight %
OSHA - Hazard
Communication
Carcinogens
OSHA - Specifically
Regulated Carcinogens
ACGIH Carcinogens
TITANIUM DIOXIDE
13463-67-7
5 - 10
Present
ETHYLENE GLYCOL
MONOBUTYL ETHER
111-76-2
5 - 10
A3 Confirmed Animal
Carcinogen with
Unknown Relevance to
Humans
12. ECOLOGICAL DATA
No information on ecology is available.
13. DISPOSAL CONSIDERATIONS
Disposal should be made in accordance with federal, state and local regulations.
14. TRANSPORTATION INFORMATION
U.S. Department of Transportation
UN ID Number (msds): UN1263
Proper Shipping Name: PAINT
Hazard Class: 3
Packing Group: II
U.S Hazmat and/or International DG shipment exceptions
The supplier may apply one of the following exceptions: Combustible Liquid, Consumer Commodity, Limited Quantity,
Viscous Liquid, Does Not Sustain Combustion, or others, as allowed under 49CFR Hazmat Regulations. Please consult
49CFR Subchapter C to ensure that subsequent shipments comply with these exceptions.
Reportable Quantity Description:
International Air Transport Association (IATA):
UN/ID No: UN1263
Proper shipping name: Paint
Hazard Class: 3
Packing Group: 11
International Maritime Organization (IMO):
UN/ID No: UN1263
Proper shipping name: PAINT
Hazard Class: 3
Packing Group: 11
Marine Pollutant No
15. REGULATORY INFORMATION
Product ID: NAW 1322
Page 6 / 8
15. REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS:
Ingredient Name
CAS -No.
Approx.
Weight %
SARA 302
SARA 313
CERCLA RQ in lbs.
DIMETHYL KETONE-
EXEMPT SOLVENT
67-64-1
50 - 55
5000
ETHYLENE GLYCOL
MONOBUTYL ETHER
111-76-2
5 - 10
YES
BUTYL ACETATE
123-86-4
1 - 5
5000
SARA 311/312 Hazard Class:
Acute: yes
Chronic: yes
Flammability: yes
Reactivity: no
Sudden Pressure: no
U.S. STATE REGULATIONS:
Right to Know:
The specific chemical identity of a component may be withheld as a trade secret under 34 Pennsylvania Code, Chapter
317.
Pennsylvania Right To Know:
BUTYL ACETATE 123-86-4
PROPRIETARY ADDITIVE Trade Secret
PROPRIETARY INERT Trade Secret
TITANIUM DIOXIDE 13463-67-7
PROPRIETARY RESIN Trade Secret
ETHYLENE GLYCOL MONOBUTYL ETHER 111-76-2
DIMETHYL KETONE- EXEMPT SOLVENT 67-64-1
Additional Non -Hazardous Materials
PROPRIETARY RESIN Trade Secret
Rule 66 status of product Not photochemically reactive.
INTERNATIONAL REGULATIONS - Chemical Inventories
US TSCA Inventory:
All components of this product are in compliance with U.S. TSCA Chemical Substance Inventory Requirements.
Canada Domestic Substances List:
All components of this product are listed on the Domestic Substances List.
16. OTHER INFORMATION
HMIS Codes
Health:
Flammability:
Reactivity:
PPE:
Product ID: NAW1322
2'
3
1
X - See Section 8 for Personal Protective Equipment (PPE).
Page 7 / 8
•
Abbreviations:
OSHA - Occupational Safety and Health Administration, IARC - International Agency for Research on Cancer, NIOSH -
National Institute of Occupational Safety and Health, NTP - National Toxicology Program, ACGIH - American
Conference of Governmental Industrial Hygienists, SCAQMD - South Coast Air Quality Management District, TSCA -
Toxic Substances Control Act, IATA - International Air Transport Association, IMO - International Maritime Organization,
DOT - Department of Transportation, NA - Not applicable, NOT ESTAB - Not established, N.A.V. - Not available, RQ -
Reportable quantity, WT - Weight, MG/CU M - Milligrams per cubic meter, G/L - Grams per liter, MM - Millimeters,
MPPCF - Millions of particles per cubic foot, PPM - parts per million, PPT - parts per thousand, TCC/PM - Tag closed
cup / Pensky-Martens, PB - Lead, PEL - Permissible exposure level, TWA - Time Weighted Average, STEL - Short term
exposure limit, C - Celsius, F - Fahrenheit.
Disclaimer:
The data on this sheet represent typical values. Since application variables are a major factor in product performance, this
information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information.
UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES NO WARRANTIES, EXPRESS OR
IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT INFRINGEMENT. VALSPAR WILL NOT BE
LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this
product is the replacement of the defective product, or a refund of its purchase price, at our option. This MSDS contains
additional information required by the state of Pennsylvania.
Preparation Information:
Prepared By:
Print date:
Revision Date:
Product ID: NAW1322
Regulatory Affairs Department
25/May/2013
25/May/2013
Page 8 / 8
DUNCAN DESIGN GROUP
1350 Manufacturing St. I Ste. 103 J Dallas, TX 75207
office: 214.748.4400 ext. 101 fax: 214.358.4401
RESPONSE TO: CITY OF TUKWILA PERMIT CORRECTION LETTER #1
Potato Corner — 2800 Southcenter Mall, Space #9077, Tukwila, WA (K-1082)
Plumbing/Gas Piping PG14-0135
Development Application #: D14-0263
October 6, 2014
Comments from- Allen Johannessen / BUILDING DEPARTMENT.
The following numbers correspond with the city reviewers comments
1. Building Type changed to Type II — Please find correction on Cover Sheet
2. Non Combustible materials — Please see notes on Cover Sheet and attached data sheets for all
materials used.
3. Please refer to comments from MEP Consultant and revised sheet P1.
4. Please see attached manufacturer's installation and owner's manual for the Auto Fryers.
5. Please see Sheet LP1 for dimensions and clearances between other Kiosks.
Comments from- Al Metzler / FIRE DEPARTMENT.
The following numbers correspond with the city reviewers comments
1. Please see attached manufacturer's installation and owner's manual for the Auto Fryers.
Comments from- Al Metzler/ PG DEPARTMENT.
The following numbers correspond with the city reviewers comments
1. Please refer to comments from MEP Consultant .
City of Tukwila
Department of Community Development
September 04, 2014
WILLIAM MILLHOLLIN
1026 SW 151 ST
BURIEN, WA 98166
RE: Correction Letter # 1
DEVELOPMENT Permit Application Number D14-0263
POTATO CORNER - 2800 SOUTHCENTER MALL - K-1082
Dear WILLIAM MILLHOLLIN,
Jim Haggerton, Mayor
Jack Pace, Director
This letter is to inform you of corrections that must be addressed before your development permit can be approved. All
correction requests from each department must be addressed at the same time and reflected on your drawings. I have
enclosed comments from the following departments:
BUILDING DEPARTMENT: Allen Johannessen at 206-433-7163 if you have questions regarding these comments.
• (GENERAL NOTE)
PLAN SUBMITTALS: (Min. size 11x17 to maximum size of 24x36; all sheets shall be the same size. New revised
plan sheets shall be the same size sheets as those previously submitted.)
(If applicable) Structural Drawings and structural calculations sheets by a registered engineer shall have a current
signed stamp -seal. Architectural design sheets and documents by a registered architect shall also have a current
signed stamp -seal.
(BUILDING REVIEW NOTES)
1. On the front sheet the Building Type shall be changed to Type II.
2. Combustible kiosks or other structures shall not be located within the mall unless constructed of any of the
following materials:
* a. Fire -retardant -treated wood complying with Section IBC 2303.2.
* b. Foam plastics having a maximum heat -release rate not greater than 100 kilowatts (105 Btu/h) when tested in
accordance with the exhibit booth protocol in UL 1975.
* c. Aluminum composite material (ACM) having a flame spread index of not more than 25 and a smoke -
developed index of not more than 450 when tested as an assembly in the maximum thickness intended for use in
accordance with ASTM E 84 or UL 723.
The plan already does specify FRT wood for framing purposes. Please specify, on the plans, other type of materials
to be used for this Kiosk to show the Kiosk shall comply with code requirements as indicated above. Provide
manufacturers data sheets for specifications of the above mentioned materials as they apply. (IBC 402.11)
3. ihe_planshows.a_grease_trap_to_be_located_belowlhe_ loor. This most likel_y_wouldsesultin_cutting through a
structural slab. Therefore a structural design by an engineer shall be required. Provide the engineers specifications
and details for this installation.
4. Provide manufacturers installation and owner's manual for the Auto Fryers.
5. On the site plan provide dimensions for the location of this kiosk and clearances between other kiosks.
FIRE DEPARTMENT: Al Metzler at 206-971-8718 if you have questions regarding these comments.
• Cooking appliances that produce grease -laden vapors typically require a class 1 hood with fire protection. Please
provide the manufacturers data sheets for the auto fryers to determine if fire protection requirements are met.
6300 Southcenter Boulevard Suite #100 • Tukwila Washington 98188 • Phone 206-431-3670 • Fax 206-431-3665
Please address the comments above in an itemized format with applicable revised plans, specifications, and/or other
documentation. The City requires that four (4) sets of revised plan pages, specifications and/or other documentation be
resubmitted with the appropriate revision block.
In order to better expedite your resubmittal, a 'Revision Submittal Sheet' must accompany every resubmittal. I have
enclosed one for your convenience. Corrections/revisions must be made in person and will not be accepted through the mail
or by a messenger service.
If you have any questions, I can be reached at 206-431-3655.
Sincerely,
/
"----icii0 'c---40...t.
Bill Rambo
Permit Technician
File No. D14-0263
6300 Southcenter Boulevard Suite #100 • Tukwila Washinnton 98188 • Phone 206-431-3670 • Fax 206-431-3665
PERMIT COORD COPY
PLAN REVIEW/ROUTING SLIP
PERMIT NUMBER: D14-0263 DATE: 10/08/2014
PROJECT NAME: POTATO CORNER
SITE ADDRESS: 2800 SOUTHCENTER MALL, K-41 *
Original Plan Submittal
X Response to Correction Letter # 1
Revision # before Permit Issued
Revision # after Permit Issued
DEPARTMENTS:
kT hug- `o't'-tr' M
Building Division gm
Public Works
AtA
Fire Prevention
Structural
Planning Division
Permit Coordinator
PRELIMINARY REVIEW:
Not Applicable
(no approval/review required)
DATE: 10/14/14
Structural Review Required
REVIEWER'S INITIALS: DATE:
APPROVALS OR CORRECTIONS:
Approved
Corrections Required
(corrections entered in Reviews)
DUE DATE: 11/11/14
Approved with Conditions X
Denied
(ie: Zoning Issues)
Notation:
REEVIEWER'S INITIALS:
DATE:
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
12/18/2013
PERMIT COORD COPY
PLAN REVIEW/ROUTING SLIP
PERMIT NUMBER: D14-0263
PROJECT NAME: POTATO CORNER
DATE: 08/12/14
SITE ADDRESS: 2800 SOUTHCENTER MALL — K-1082
X Original Plan Submittal
Response to Correction Letter #
Revision # before Permit Issued
Revision # after Permit Issued
DEPARTMENTS:
Cowf-
g
Buildin Division
Public Works
Cowl- +4441
Fire Prevention
Structural
IJ \k
Planning Division
Permit Coordinator
o111}.19
PRELIMINARY REVIEW:
Not Applicable ❑
(no approval/review required)
DATE: 08/14/14
Structural Review Required
REVIEWER'S INITIALS: DATE:
APPROVALS OR CORRECTIONS:
Approved
Corrections Required
Approved with Conditions
Denied
(corrections entered in Reviews) (ie: Zoning Issues)
DUE DATE: 09/11/14
Notation:
REVIEWER'S INITIALS:
DATE:
Permit Center Use Only n , r
CORRECTION LETTER MAILED: 4 9
Departments issued corrections: Bldg- Fire Ping ❑ PW 0 Staff Initials:
ttit
12/18/2013
City of Tukwila
REVISION.
SUBNIITTAL
Department of Community Development
6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone: 206-431-3670
Web site: http://www.TukwilaWA.gov
Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through
the mail, fax, etc.
Date: 10/08/2014 Plan Check/Permit Number: D14-0263
(— Response to Incomplete Letter #
Response to Correction Letter # 1
Revision # after Permit is Issued
Revision requested by a City Building Inspector or Plans Examiner
Project Name: Potato Corner
Project Address: 2800 Southcenter Mall #K-1082
Contact Person: William Millhollin
Summary of Revision:
Please see attached
RECEIVED
CI4V OF itjgwi1
OCT 0 8 2014
PERMJT comp
Phone Number: (206) 601-7043
Sheet Number(s): "Cover" (Page 1) - Plumbing page (P1) - Site View (LP1)
"Cloud" or highlight all areas of revision including date of revision
Received at the City of Tukwila Permit Center by:
14/ Entered in Permits Plus on /0/0V
H:\Applications\FonwApplications On Line \2010 Applications\7.2010 - Revision Submittal doe
Revised: May 2011
WESTMARK CONSTRUCTION INC
Page 1 of 3
a5hington State 'Departiiient of
abor & Industries
WESTMARK CONSTRUCTION INC
Owner or tradesperson
JOHNSON, WARD M
Principals
JOHNSON, WARD M, PRESIDENT
FRANK, THOMAS A, VICE PRESIDENT
JOHNSON, BRIAN
CHRISTOPHER, SECRETARY
JOHNSON, JOY, SECRETARY
(End: 03/11/2011)
JOHNSON, W GLENN, TREASURER
(End: 03/23/2011)
Doing business as
WESTMARK CONSTRUCTION INC
WA UBI No.
600 040 824
6102 N 9TH ST STE 400
TACOMA, WA98406-2036
253-564-4620
PIERCE County
Business type
Corporation
License
Verify the contractor's active registration / license / certification (depending on trade) and any past violations.
Construction Contractor Active.
Meets current requirements.
License specialties
GENERAL
License no.
WESTMCI012D3
Effective — expiration
03/23/1999— 03/30/2015
Bond
Safeco Ins Co of America
Bond account no.
69S001376
Received by L&I
05/08/2012
Bond history
$12,000.00
Effective date
04/20/2012
Expiration date
Until Canceled
Insurance
https://secure.lni.wa.gov/verify/Detail.aspx?UBI=600040824&LIC=WESTMCI012D3&SAW= 11/26/2014