HomeMy WebLinkAboutPermit D15-0158 - ANDOVER EXECUTIVE PARK - 742 BUILDING REROOFANDOVER EXECUTIVE
PARK - 742
742 INDUSTRY DR
D15-0158
City of Tukwila
Department of Community Development
• 6300 Southcenter Boulevard, Suite #100
Tukwila, Washington 98188
Phone:206-431-3670
Inspection Request Line: 206-438-9350
Web site: http://www.TukwilaWA.eov
DEVELOPMENT PERMIT
Parcel No: 2523049008 Permit Number: D15-0158
Address: 742 INDUSTRY DR Issue Date: 7/20/2015
Permit Expires On: 1/16/2016
Project Name: ANDOVER EXECUTIVE PARK
Owner:
Name:
BLUE DOG PROPERTIES TRUST
Address:
PO BOX 847 C/O THOMSON REUTERS
PTS, CARLSBAD, WA, 92018
Contact Person:
Name:
STEVE STONE
Address:
9500 AURORA AVE N , SEATTLE, WA,
98103
Contractor:
Name:
TECTA AMERICA SEATTLE LLC
Address:
9500 AURORA AVE N , SEATTLE, WA,
98103
License No:
TECTAAS905DH
Phone: (206) 522-5436
Phone: (425) 881-9190
Expiration Date:
Lender:
Name: NCPW ANDOVER EXECUTIVE PARK
Address: 810 NW MARSHALL#300, PORTLAND,
OR, 97209
DESCRIPTION OF WORK:
OVER LAY THE EXISTING CAP SHEET ROOF WITH A SINGLE PLY TPO ROOF SYSTEM
Project Valuation: $98,742.00 Fees Collected: $2,559.00
Type of Fire Protection: Sprinklers:
Fire Alarm:
Type of Construction: Occupancy per IBC:
Electrical Service Provided by: TUKWILA FIRE SERVICE Water District: TUKWILA
Sewer District: TUKWILA SEWER SERVICE
Current Codes adopted by the City of Tukwila:
International Building Code Edition:
2012
National Electrical Code:
2014
International Residential Code Edition:
2012
WA Cities Electrical Code:
2014
International Mechanical Code Edition:
2012
WAC 296-466:
2014
Uniform Plumbing Code Edition:
2012
WA State Energy Code:
2012
International Fuel Gas Code:
2012
Public Works Activities:
Chan nelization/Striping:
Curb Cut/Access/Sidewalk:
Fire Loop Hydrant:
Flood Control Zone:
Hauling/Oversize Load:
Land Altering: Volumes: Cut: 0 Fill: 0
Landscape Irrigation:
Sanitary Side Sewer: Number: 0
Sewer Main Extension:
Storm Drainage:
Street Use:
Water Main Extension:
Water Meter: No
Permit Center Authorized Signature: 1/19 6' Date: l
I hearby certify that I have read and examined this permit and know the same to be true and correct. All
provisions of law and ordinances governing this work will be complied with, whether specified herein or not.
The granting of this permit does not presume to give authority to violate or cancel the provisions of any other
state or local laws regulating construction or the performance of work. I am authorized to sign and obtain this
development permit and agree to the conditions attached to this permit.
Signature: Date:
Print Name:
This permit shall become null and void if the work is not commenced within 180 days for the date of issuance, or if
the work is suspended or abandoned for a period of 180 days from the last inspection.
PERMIT CONDITIONS:
1: 'BUILDING PERMIT CONDITIONS'
2: Work shall be installed in accordance with the approved construction documents, and any changes made
during construction that are not in accordance with the approved construction documents shall be
resubmitted for approval.
3: All permits, inspection record card and approved construction documents shall be kept at the site of work
and shall be open to inspection by the Building Inspector until final inspection approval is granted.
4: All construction shall be done in conformance with the Washington State Building Code and the
Washington State Energy Code.
S: Remove all demolition rubble and loose miscellaneous material from lot or parcel of ground, properly cap
the sanitary sewer connections, and properly fill or otherwise protect all basements, cellars, septic tanks,
wells, and other excavations. Final inspection approval will be determined by the building inspector based
on satisfactory completion of this requirement.
6: VALIDITY OF PERMIT: The issuance or granting of a permit shall not be construed to be a permit for, or an
approval of, any violation of any of the provisions of the building code or of any other ordinances of the City
of Tukwila. Permits presuming to give authority to violate or cancel the provisions of the code or other
ordinances of the City of Tukwila shall not be valid. The issuance of a permit based on construction
documents and other data shall not prevent the Building Official from requiring the correction of errors in
the construction documents and other data.
PERMIT INSPECTIONS REQUIRED
Permit Inspection Line: (206) 438-9350
1700 BUILDING FINAL"
0103 PRE-REROOF
CITY OF TUKWILA Building Permit No. �7 "
CommunityDevelopment Department
' Public Works Department Project No.
• Permit Center
6300 Southcenter Blvd., Suite 100 Date Application Accepted:
" Tukwila, WA 98188 Date Application Expires:
http://www.TukwilaWA.p,ov
oI o 1ce use ont
CONSTRUCTION PERMIT APPLICATION
Applications and plans must be complete in order to be accepted for plan review.
Applications will not be accepted through the mail or by fax.
*Please Print"
SITE LOCATION
Site Address: 742 Industry Dr Tukwila W` jA
Tenant Name: W O__
PROPERTY OWNER
Name: Blue Dog Properties
Address: PO Box 847 C/O Thomson Reuters
City: PTS, Carlsbad State: WA Zip: 92018
CONTACT PERSON — person receiving all project
communication
Name: Steve Stone
Address: 9500 Aurora Ave N
City: Seattle State: WA Zip: 98103
Phone: (206) 455-7459 Fa": (206) 522-5472
Email: sstone@tectaamerica.com
GENERAL CONTRACTOR INFORMATION
Company Name: Tecta America Seattle LLC
Address: 9500 Aurora Ave N
City: Seattle State: WA Zip: 98103
Phone: (206) 522-5436 Fax: (206) 522-5472
COntr Reg NO.: TECTAAS905DH Exp Date: 07/01/2017
Tukwila Business License No.: &kL _ d q l? q5__7
King Co Assessor's Tax No.:
Suite Number: Floor:
New Tenant: ❑ .....Yes O..No
ARCHITECT OF RECORD
Company Name: N/A
Architect Name:
Address:
City: State: Zip:
Phone: Fax:
Email:
ENGINEER OF RECORD
Company Name: N/A
Engineer Name:
Address:
City: State: Zip:
Phone: Fax:
Email:
LENDER/BOND ISSUED (required for projects $5,000 or
greater per RCW 19.27.095)
Name: NCPW Andover Executive Park LL
Address: 810 NW Marshall #300
City: Portland State: OR Zip: 97209
H:\Appliefftiom\Forms-ApplicatiomOnLine\2011 ApplicationsTermil Application Revised - 8-9-11.docx
Revised: August 2011 Page I of 4
bh
BUILDING PERMIT INFORMATIOI, — 206-431-3670
Valuation of Project (contractor's bid price): $ 98,742 Existing Building Valuation:
Describe the scope of work (please provide detailed information):
Over -lay the existing cap sheet roof with a single -ply TPO roof system
Will there be new rack storage? ❑..... Yes Q].. No If yes, a separate permit and plan submittal will be required.
Provide All Building Areas in Square Footage Below
Existing
Interior Remodel
Addition to
Existing
Structure
New
Type of
Construction per
IBC
Type of
Occupancy per
IBC
I' Floor
2nd Floor
3'd Floor
Floors thru
Basement
Accessory Structure*
Attached Garage
Detached Garage
Attached Carport
Detached Carport
Covered Deck
Uncovered Deck
PLANNING DIVISION:
Single family building footprint (area of the foundation of all structures, plus any decks over 18 inches and overhangs greater than 18 inches)
*For an Accessory dwelling, provide the following:
Lot Area (sq ft): Floor area of principal dwelling: Floor area of accessory dwelling:
*Provide documentation that shows that the principal owner lives in one of the dwellings as his or her primary residence.
Number of Parking Stalls Provided: Standard: Compact: Handicap:
Will there be a change in use? El ....... Yes ❑....... No If "yes", explain:
FIRE PROTECTION/HAZARDOUS MATERIALS:
❑ ....... Sprinklers ❑ ....... Automatic Fire Alarm ❑ .......None ❑ .......Other (specify)
Will there be storage or use of flammable, combustible or hazardous materials in the building? ❑ ....... Yes ❑ .......No
If `yes', attach list of materials and storage locations on a separate 8-112"x II " paper including quantities and Material Safety Data Sheets.
SEPTIC SYSTEM
❑ .......On -site Septic System — For on -site septic system, provide 2 copies of a current septic design approved by King County Health
Department.
H:VApplications%Fortm-Applications On Line\2011 ApplicationsTermit Application Revised - 8-9-11.docx
Revised: August 2011 Page 2 of 4
bh
PERMIT APPLICATION NOTES —
Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject
to possible revision by the Permit Center to comply with current fee schedules.
Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation.
The Building Official may grant one or more extensions of time for additional periods not exceeding 90 days each. The extension shall be
requested in writing and justifiable cause demonstrated. Section 105.3.2 International Building Code (current edition).
I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER
PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT.
BUILDING OWNER
Print Name:
Day Telephone:
Date: 6 -ZS is'
Mailing Address:
City stag zip
H:\Applications\Forms-Applications On line\201 1 ApplicationsTermit Application Revised - 8-9-I l.docz
Revised: August 2011
Page 4 of 4
DESCRIPTIONS ACCOUNT QUANTITY PAID
PermitTRAK $5,946.66
D15-0158 Address: 742 INDUSTRY DR Apn: 2523049008 $2,559.00
DEVELOPMENT $2,483.87
PERMIT FEE
R000.322.100.00.00
0.00
$1,502.65
PLAN CHECK FEE
R000.345.830.00.00
0.00
$976.72
WASHINGTON STATE SURCHARGE
B640.237.114
0.00
$4.50
TECHNOLOGY FEE $75.13
TECHNOLOGY FEE
R000.322.900.04.00
0.00
$75.13
D15-0159 Address: 564 INDUSTRY DR Apn: 0223400010 $1,441.34
DEVELOPMENT $1,399.08
PERMIT FEE
R000.322.100.00.00
0.00
$845.20
PLAN CHECK FEE
R000.345.830.00.00
0.00
$549.38
WASHINGTON STATE SURCHARGE
B640.237.114
0.00
$4.50
TECHNOLOGY FEE $42.26
TECHNOLOGY FEE
R000.322.900.04.00
0.00
$42.26
D15-0160 Address: 630 INDUSTRY DR Apn: 2523049008 $1,946.32
DEVELOPMENT $1,889.21
PERMIT FEE
R000.322.100.00.00
0.00
$1,142.25
PLAN CHECK FEE
11000.345.830.00.00
0.00
$742.46
WASHINGTON STATE SURCHARGE
6640.237.114
0.00
$4.50
TECHNOLOGY FEE $57.11
TECHNOLOGY FEE R000.322.900.04.00 0.00 $57.11
TOTAL' . .
Date Paid: Friday, June 26, 2015
Paid By: STEVE GRINAKER
Pay Method: CREDIT CARD 08327G
Printed: Friday, June 26, 2015 9:06 AM 1 of 1
CPSYS7EM5
J
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO. PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670
Permit Inspection Request Line (206) 438-9350
Pr jecr
o t/ff- � /� F_
Type �Igsglectio�
(GaC
Address:
Z_ c:
Date Calle .
Special Instructions: f
d
I�1.1`'op
Date Wanted: a.m.
— p.m.
Requ ter:
Phone No:
Inspector: Date: r ` C--
u REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be
paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection.
t
INSPECTION RECORD
Retain a copy with permit
INSPECTION NO. PERMIT NO.
CITY OF TUKWILA BUILDING DIVISION
6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670
Permit Inspection Request Line (206) 438-9350
Pr 'ect: t
Type of Inspection:
Address.
7
Date Called:
Special Instructions: I
Date Wanted: a.m.
" p.m.
Requester:
Phone No:
Approved per applicable codes. E Corrections required prior to approval.
IInspector 4 IDate:
REINSMECTION FEE REQUIRED. Prior to next inspection, fee must be
paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection.
AS
$ PARATE PERMIT
REQUIRED FOR:
armed *A
Mectrical
Gfii=►umbing
was "
CiV of Tukwila
REVISIONS
No changes shall be made to the scope
Of work ti►ithout prior approval of
I ukivila Building Division.
hDji= Pia``i3ians will require a new plan submittal
end may include additional plan review fees.
a,
FILE COPY
Permit No. " 0.1
S
Plan review approval is subjea to en= Wd moons.
Approval of construction dmmwb dtres not author
the violation of any adopted 006 or wdna . Receipt
Of approved Field is adMwledggd:
BY;����
Date:
City of Tukwila
BUILDING DIVISION
REVi'EWED FOR
CODE COMPLIANCE
APPROVED
JUL 15 2015
A-7 ij"
City of Tukwila
BUILDING DIVISION
r
Ln
0
0
C-
4F
N
w
0
0
(i
Q
cr
_J
03
w
WX
N
Z
Lu
W F"
N
U
LU,! O
Z
~
cc
W
U
a
;EViE—WED FOR
DE COMPLIANCE
APPROVED
JUL 15 2015
City of Tukwila
lLDINIG DiVISIG
o n anv�lle
Ffeec[cVac!�<el eJrodasticJ
Meets or exceeds the requirements of ASTM D 6878
Features and Components
Integral Polyester Fleece Backing- In -line application of fleece
allows for stronger bond for polyester backing that gives more
flexibility in varying substrates for mechanically fastened or
adhered systems.
One of the Widest Melt Windows: Promotes better welds over a
wider variety of speeds and temperatures, and leads to a softer,
more flexible and workable sheet
Reinforced fabric scrim layer and top -ply thickness: Lends to
durable physical properties including:
• Long-term weathering, UV resistance and heat -aging properties
• High breaking and tearing strength
Optimized TPO formulation: delivers high-performance ozone
resistance, cool roof reflectivity and overall weather resistance.
21
Ij
Polyolcl n Ve�r,brane
t� 0 TM
"iWiPLIAZCE
side PN
JUL 15 2015
r�3�UILDIf���D1VISlt���
Colors
Grey I White I Tan* R C E I VE D
*Grey and tan are special order only. CITY QF'TUKWILA
JUN 2 S 2015
System Compatibility This product maybe used as a component in the following systems. Please reference product application for specific installaprimRMJnTin(".TER
d d
Do not use with Multi -Ply systems U+ Compatible with the selected Single Ply systems above
Key. HA = Hot Applied CA = Cold Applied HW = Heat Weldable SA = Self Adhered MF = Mechanically Fastened FA = Fully Adhered BA = Ballasted
Energy and the Environment
Standard
Reflecti '
Emissi '
CRRC®
Initial
0.77
0.87
3 Yr. Aged
0.70
0.86
CA Title 24
Pass
0.77
0.87
ENERGY STAR®
Initial
0.78
0.87
3 Yr. Aged
0.68
Not Tested
LEED®
SRI
101
Recycled Content
Post -consumer 0%
Post-industrial: 5 /o
Results shown are for the initial reflectivity and emittance forwhite membranes unless
otherwise indicated; emissivity values for California Title 24 are tested per ASTM C 1371;
LEED emissivity values are tested per ASTM E 408.
Peak Advantage° Guarantee Information
Product Guarantee Term
J M TPO FB 115 15 or 20 years
Codes and Approvals
�TuS
$SIFr
FM
C rdl.mw.e.ca,mr
.,PROVED produq Control Approved
Installation/Application
&no
Fully Adhered Mechanically Hot Air Weld
Fastened
Refer to JM TPO application guides and detail drawings
for instructions.
Packaging and Dimensions
Roll Width
10' (3.05 m)
Roll Length
100' (30.48 m)
Roll Coverage
1000 ftz (92.9 mz)
Rolls per Pallet
6
Pallet Weight
2,303 lb (1,045 kg)
Pallets per Truck*
16
Producing Location
Scottsboro, AL
*Assumes 48' flatbed truck and does not reflect pallets of accessories or impact of mixed sizes.
D 15-0158
Refer to the Safety Data Sheet and product label prior to using this product
The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at
www.im.coMroofing. RS-136;i9 1-15 (Replaces 10.14)
r
r-1 r r•
Fleece Backed Thermoplastic Pol olefin Membrane
P Y
Meets or exceeds the requirements of ASTM D 6878
Tested Physical Properties
o
Breaking Strength, min, Ibf (N)
D 751
220 (976)
499 (2,220)
450 (2,002)
Elongation at Break, min %
D 751
15
29
27
Tearing Strength, min, Ibf (N)
D 751
45 (200)
91(404)
146 (649)
Factory Seam Strength, min, Ibf (N)
D 751
66 (290)
171(761)
Thickness, min, in.
D 751
+/ 10% from Nominal
0.060 (Nominal)
&
m
Thickness Over Scrim, min, in. (mm)
D 7635
0.015
0.027 (0.686)
g
Water Absorption, max, %
D 471
3.0
0.08
Britdeness Point, max, -40°F
D 2137
No Cracks
Pass
Properties after Heat Aging @ 240°F
D 573
Pass/Fail
Pass
„
Breaking Strength, % (after aging)
D 751
90
>90
>90
a €
Elongation, % (after aging)
D 751
90
>90
>90
m
Tearing Strength, % (after aging)
0751
60
>60
>60
Weight Change, max, % (after aging)
D 751
f1.0
0.25
Unear Dimensional Change, max, % (after 6 hrs @ 158°F)
D 1204
t1.0
<0.2
Accelerated Weathering, min
G 151 & G 155
10,080 kyrn'"nm @ 340 nm
(4,000 hrs @ 0.70 W)
10,080 kYm2
(4,000 hrs)
€
3
Cracking (@7x magnification)
G 155
No Cracks
Pass
1. JM TPO R3115 is comprised of a 60 Ml TPO membrane and an integral fleece bacldng.
The given physical properties are based on the JM TPO 60 Ml membrane.
" MD= Machine Direction
""XMD =Goss -Machine Direction
Note: All data represents tested values.
Supplemental Testing
Dynamic Puncture
D 5635
N/A
Pass @ 27.5 Joules
Static Puncture
D 5602
N/A
Pass @ 44lb (20 kg)
Reflectance
C 1549
N/A
78%
Emittance
C 1371
N/A
0.87
Refer to the Safety Data Sheet and product label prior to using this product
The Safety Data Sheet is available by calling (800) 922-5922 or on the Web at
www.im.conVroofing. RS-8639 1-15 (Replaces 10-14)
SIM"
lohrtsNramnile
717 inn St
ow,rer, co am
00)s22-6M
www{m.,owrn OO&g
Bulletin Number: M10-004
Date: January 13, 2010
Distribution: External
Johns Manville Introduces JM TPO FB 115 and JM TPO FB 135
Fleece -backed Membranes
Single Ply Roofing Systems
Johns Manville is proud to announce the introduction of fleece -backed TPO into the
JM TPO product portfolio. The introduction of fleece -backed membranes enhances
Johns Manville's premier TPO offering and confirms our commitment to our valued
single ply customers.
Membranes
JM TPO FB 135 is a white, 80 mil membrane with an integral fleece backing. It is
available in 10' wide by 50' long rolls.
JM TPO FB 115 is a white, 60 mil membrane with an integral fleece backing. It is
available in 10' wide by 100' long rolls.
JM TPO FB 115 is an SPPI product with up to a six week lead time. Additionally,
projects will be evaluated individually to ensure the performance and quality
standards our customers have come to expect with our existing JM TPO line.
Accessories
Johns Manville also offers accessories for our fleece backed offering. Use the JM
TPO Reinforced Cover Strip for stripping in end laps as well as the JM TPO Curb
Flashing for vertical transitions.
Stocking
Fleece -backed products will be produced, stocked and shipped from our Scottsboro,
Alabama manufacturing facility. In order to ensure the most consistent product and
delivery possible, the Scottsboro facility will be the only location to stock and fill
orders.
Look for expanded product options and innovations in the coming months as we
continue to make our fleece products another successful portion of our TPO portfolio.
Thank you very much for your support and help as we continue to make the best TPO
product on the market even better!
TJ Stock
Product Manager
1/7"
Johns Manville
Description
JM TPO FB 115 thermoplastic polyolefin (TPO) membranes are rein-
forced with a polyester fabric and integral polyester fleece backing.
The membrane is designed for use in mechanically fastened and
fully adhered roofing applications.
Use
Install JM TPO FB 115 Membranes in new, re -roof (tear -off) and re-
cover roof constructions. In re-cover constructions, if the existing
roof is sound, the single ply membrane can eliminate the cost of
disposing the original roof.
Colors
White, Grey* and Tan*
Standard Sizes
Color
White, Grey* and Tan* 10' x 100' (3.05 m x 30.48 m)
*Grey and tan are special order only.
Installation
Since JM TPO FB 115 Membranes are thermoplastic, they can be
rolled out onto the roof substrate and easily welded into one homo-
geneous sheet using hot-air welding procedures.
JM TPO FB 115 Membranes can be mechanically fastened or
adhered t0 the structural roof deck. Application must be in accor-
dance with JM Peak Advantage® Guarantee requirements, build-
ing codes, published standard fastening patterns or adhesives
recommendations. Install JM TPO FB 115 products in accordance
with current JM TPO Applicator Guides or Detail Drawings.
JM TPO FB 11r
Fleece Backed Roofing Membrane
Approvals
JM mechanically fastened and adhered TPO FB 115 roof systems are
classified by UL11(Underwriters Laboratories Inc.) and FM Global
(Factory Mutual). When searching in RoofNav for a specific approval,
be sure to indicate the mil thickness desired, i.e., JM TPO FB.
Enerqy and the Environment
CRRC®
Initial Reflectivity:0.77 Emissivity:0.87
California
Pass Reflectivity:0.77 Emissivity:0.87
Title 24
ENERGY
Initial Reflectivity:0.78
STAR®
3 Yr. Aged Reflectivity: 0.68
Cleaned 3 Yr. No
LEED®
SRI of 101 as tested by ASTM E 1980.
Recycled Content:
Postconsumer:0% Postindustrial:0%
Producing Locations: Scottsboro, AL
Results shown are for the initial reflectivity and emittance for white membranes unless
indicated; emissivity values for California Title 24 are tested per ASTM C 1371; LEED
emissivity values are tested per ASTM E 408.
JIM Peak Advantage Guarantees
Enhanced guarantees are now available on certain systems for
wind and puncture. Consult your local sales representative for
more information aboutthe new Single Ply Guarantee Charges
Requirements Guide for specific guarantee terms and costs.
Product Mechanically Fastened or Fully Adhered
JM TPO FB 115 15 or 20 year
JM TPO FB 115 Membranes meet or exceed all of the requirements of ASTM D 6878.1
Tested Physical Properties
Property
ASTM ASTM
Test Method Requirements
60 Mil
Overall Sheet Thickness D 751 >0.039 in. 0.0 mm) 0.060 in. (1.52 mm)
Thickness of Coating Over Fabric Weather Side D 6878 >0.012 in. (.305 mm) 0.027 in. (.69 mm)
Breaking Strength
D 751
Elongation at Reinforcement Break
D 751
Tearing Strength
D 751
Brittleness Point
D 2137
Ozone Resistance (no cracks) D 1149
Heat Aging (Pass/Fail) D 573
** MD: Machine Direction
XMD: Cross Machine Direction
UM TPO FB 115 is comprised of a 60 Mil TPO membrane and an integral fleece backing
The given physical properties are based on the JM TPO 60 Mil membrane.
M D** XM D**
>220 Ibf (978 N) 325.83 Ibf (1,449.36 N) 335.73lbf (1,493.40 N)
>15% 42.41% 34.93%
>55 Ibf (245 N) 89.8 Ibf (339.45 N) 184.6 Ibf (821.14 N)
-40°C (-40°F) Pass @ -40°C (-40*F)
0 rating
Pass Pass
RS-8639 12-09 (Replaces 11-09)
Johns Manville
JM TPO FB 115"m (Cont'd)
Fleece Backed Roofing Membrane
JM TPO FB 115 Membranes meet or exceed all of the requirements of ASTM D 6878?
Tested Physical Properties
Property ASTM ASTM
Test Method Requirements j 60 Mil
MD** XMD**
Post Heat Aged Breaking Strength D 751 >90% 328.14lbf (1,459.64 N) 334.16 Ibf (1,486.42 N)
retained values
Post Heat Aged Elongation at Reinforcement Break D 751 >90% 39.10% 35.14%
retained values
Post Heat Aged Tearing Strength
D 751
>60% 1
77.1 Ibf (342.96 N)
245.0 Ibf (1,089.81N)
retained values I
Post Heat Aged Weight Change
D1204
±1%max.
<0I%
Post Heat Aged Linear Dimension Change
D 6878
±1% max.
<0.1%%
Water Absorption
D 471
±3.0% max.
02.20%
Factory Seam Strength
D 751
>66 Ibf (294 N)
140.48 Ibf (624.89 N)
Post Xenon Visual Inspection
D 6878
Pass
Pass
** MO: Machine Direction
XMD: Cross Machine Direction
UM TPO FB 115 is comprised of a 60 Mil TPO membrane and an
integral fleece backing.
The given physical properties
and supplemental testing are based on the JM TPO 60 Mil
membrane.
Supplemental Testinq
Property
ASTM
Test Method
ASTM
Requirements
60 Mil
Dynamic Puncture
D 5635
N/A
27.5 Joules
Static Puncture
D 5602
N/A
Pass @ 44lb (20 kg)
Reflectance
C 1549
N/A
80.78%
Emittance
C 1371
N/A
0.86
Refer to the Material Safety Data Sheet prior to using JM TPO
FB 115. Material Safety Data Sheet is available by calling
(800) 922-5922 or on the Web at www.im.com/roofing.
RS-8639 12-09 (Replaces 11-09)
-.
I m
1"17
Johns Manville
Description
JM TPO FB 135 thermoplastic polyolefin (TPO) membranes are rein-
forced with a polyester f a bric and integral polyester fleece backing.
The membrane is designed for use in mechanically fastened and
fully adhered roofing applications.
Use
Install JM TPO FB 135 Membranes in new, re -roof (tear -off) and re-
cover roof constructions. In re-cover constructions, if the existing
roof is sound, the single ply membrane can eliminate the cost of
disposing the original roof.
Colors
White, Grey* and Tan*
Standard Sizes
Color
White, Grey* and Tan* 10' x 100' (3.05 m x 30.48 m)
* Grey and tan are special order only.
Installation
Since JM TPO FB 135 Membranes are thermoplastic, they can be
rolled out onto the roof substrate and easily welded into one homo-
geneous sheet using hot-air welding procedures.
JM TPO FB 135 Membranes can be mechanically fastened or
adhered to the structural roof deck. Application must be in accor-
dance with JM Peak Advantage° Guarantee requirements, build-
ing codes, published standard fastening patterns or adhesives
recommendations. Install JM TPO FB 135 products in accordance
with current JM TPO Applicator Guides or Detail Drawings.
JM TPO FB 13r
Fleece Backed Roofing Membrane
Approvals
JM mechanically fastened and adhered TPO FB 135 roof systems are
classified by UL® (Underwriters Laboratories Inc.) and FM Global
(Factory Mutual). When searching in RoofNav for a specific approval,
be sure to indicate the mil thickness desired, i.e., JM TPO FB.
Enerqy and the Environment
CRRC°
Initial Reflectivity:0.77 Emissivity:0.87
California
Pass Reflectivity:0.77 Emissivity:0.87
Title 24
ENERGY
Initial Reflectivity:0.78
STAR®
3 Yr. Aged Reflectivity: 0.68
Cleaned 3 Yr. No
LEED®
SRI of 101 as tested by ASTM E 1980.
Recycled Content:
Postconsumer:0% Postindustrial:0%
Producing Locations: Scottsboro, AL
Results shown are for the initial reflectivity and emittance for white membranes unless
indicated; emissivity values for California Title 24 are tested per ASTM C 1371; LEED
emissivity values are tested per ASTM E 408.
JIM Peak Advantage Guarantees
Enhanced guarantees are now available on certain systems for
wind and puncture. Consult your local sales representative for
more information aboutthe new Single Ply Guarantee Charges
Requirements Guide for specific guarantee terms and costs.
Product Mechanically Fastened or Fully Adhered
JM TPO FB 135 15 or 20 year
JM TPO FB 135 Membranes meet or exceed all of the requirements of ASTM D 6878?
Tested Physical Properties
Property ASTM ASTM
Test Method Requirements
80 Mil
Overall Sheet Thickness
Thickness of Coating Over Fabric Weather Side
Breaking Strength
Elongation at Reinforcement Break
Tearing Strength
Brittleness Point
Ozone Resistance (no cracks)
Heat Aging (Pass/Fail)
D 751
D 6878
D 751
D 751
D 751
D 2137
D 1149
D 573
>0.039 in. (1.0 mm)
>0.012 in. (.305 mm)
>220 Ibf (978 N)
>15%
>55 Ibf (245 N)
-40°C (-40°F)
Pass
0.081 in. (2.05 mm)
0.035 in. (.889 mm) ±10%
MD**
XMD**
372lbf (1,655 N)
374lbf (1,664 N)
38.53%
35.75%
81.9 Ibf (364 N)
2141bf (952 N)
Pass Q -40*C (-40°F)
0 rating
Pass
** MD: Machine Direction
XMD: Cross Machine Direction
UM TPO FB 135 is comprised of a 80 Mil TPO membrane and an integral fleece backing.
The given physical properties are based on the JM TPO 80 Mil membrane.
RS-8644 11-09 (New)
Johns Manville
/ "117
JM TPO FB 135' (Cont'd)
Fleece Backed Roofing Membrane
NIMEMEMM
JM TPO FB 135 Membranes meet or exceed all of the requirements of ASTM D 6878?
Tested Physical Properties
Property
ASTM
ASTM
80 Mil
Test Method
Requirements
MD**
XMD**
Post Heat Aged Breaking Strength
D 751
>90%
361 Ibf (1,606 N)
378 Ibf (1,681 N)
retained values
Post Heat Aged Elongation at Reinforcement Break
D 751
>90%
36.67%
34.29%
retained values
Post Heat Aged Tearing Strength
D 751
>60%
80.4 Ibf (357.64 N)
192.6 Ibf (856.73 N)
retained values
Post Heat Aged Weight Change
D1204
±1%max.
<1%
Post Heat Aged Linear Dimension Change
D 6878
±1% max.
<0%
Water Absorption
D 471
±3.0% max.
1.4%
Factory Seam Strength
D 751
>66 Ibf (294 N)
96.33 Ibf (428.50 N)
Post Xenon Visual Inspection
D 6878
Pass
Pass
** MD: Machine Direction
XMD: Cross Machine Direction
UM TPO FB 135 is comprised of a 80 Mil TPO membrane and an integral
fleece backing. The
given physical properties and supplemental testing are based on the JM TPO 80 Mil
membrane.
Supplemental Testing
Property
ASTM
Test Method
ASTM
Requirements
80 Mil
Dynamic Puncture
D 5635
N/A
35 Joules
Static Puncture
D 5602
N/A
Pass @ 44Ib (20 kg)
Reflectance
C 1549
N/A
81.52%
Emittance
C 1371
N/A
0.86
Refer to the Material Safety Data Sheet prior to using JM TPO
FB 135. Material Safety Data Sheet is available by calling
(800)922-5922 or on the Web at www.im.com/roofing.
RS-8644 11-09 (New)
PERMIT COORD COPY
PLAN REVIEW/ROUTING SLIP
PERMIT NUMBER: D15-0158
DATE: 06/26/15
PROJECT NAME: ANDOVER EXECUTIVE PARK - 742
SITE ADDRESS: 742 INDUSTRY DR
X Original Plan Submittal Revision # before Permit Issued
Response to Correction Letter # Revision # after Permit Issued
DEPARTMENTS:
h4 "& -411
Building Division
Public Works ❑
PRELIMINARY REVIEW:
Not Applicable ❑
(no approval review required)
REVIEWER'S INITIALS:
APPROVALS OR CORRECTIONS:
Approved ❑
Corrections Required ❑
(corrections entered in Reviews)
Notation:
REVIEWER'S INITIALS:
inIA- -�- I + IT
revention U Planning Division ❑
Structural ❑ Permit Coordinator ❑
DATE: 06/30/15
Structural Review Required ❑
DATE:
DUE DATE: 07/28/15
Approved with Conditions e
Denied ❑
(ie: Zoning Issues)
DATE:
Permit Center Use Only
CORRECTION LETTER MAILED:
Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials:
12/18/2013
TECTA AMERICA SEATTLE LLC-
Page 1 of 3
Washington State Department of
,y ; Labor & Industries
TECTA AMERICA SEATTLE LLC
Home Inicio en Espanol Contact Search L&i ��� 1:�Inl�
A-Z Index Help bfy Secure I: `.1
Safety Claims & Insurance Workplace Rights Trades & Licensing
Owner or tradesperson 9500 AURORA AVE N
Principals SEATTLE, WA98103
p 206-522-5436
KRUSE, ERIN JANEANE KING County
GRINAKER, MANAGER
REGINELLI, DAVID R, MANAGER
GRINAKER, KEVIN R, MANAGER
SMITH, BRYNNE E, MANAGER
(End: 06/02/2015)
GRINAKER, STEVEN LYLE, MANAGER
(End: 06102/2015)
KRACHT, TODD N, PARTNER/MEMBER
(End: 06/24/2013)
SONTACRONE,MARK
F, PARTNER/MEMBER
(End: 06/24/2013)
FORBES, STEPHEN A, MANAGER
(End: 06/24/2013)
Doing business as
TECTA AMERICA SEATTLE LLC
WA UBI No. Business type
602 730 183 Limited Liability Company
License
Verify the contractor's active registration / license / certification (depending on trade) and any past violations.
Construction Contractor Active.
..... _ ...................... _........................................
Meets current requirements.
License specialties
GENERAL
License no.
TECTAAS905DH
Effective — expiration
03/08/2010— 07/01/2017
Bond
................
XL SPECIALTY INS CO
$12,000.00
Bond account no.
US00069035SU15A
Received by L&I
Effective date
05/13/2015
06/22/2015
Expiration date
Until Canceled
Bond history
Insurance
...1.........................
https:Hsecure.Ini.wa.gov/verify/Detail.aspx?UBI=602730183&LIC=TECTAAS905DH&SAW= 7/20/2015