The URL can be used to link to this page

Home My WebLink AboutPermit PG16-0017 - HABIT BURGER - FLOOR DRAINS, VENT PIPES, LINES, SINKS ETCIfor4l 61110 8 : tl" 1 17025SOUTHCENTER PKWY PG16-0017 City of Tukwila • Department of Community Development • 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Inspection Request Line: 206-438-9350 Web site: http://www.TukwilaWA.gov PLUMBING/GAS PIPING PERMIT Parcel No: 2623049070 Permit Number: PG16-0017 Address: 17025 SOUTHCENTER PKWY Issue Date: 4/26/2016 Permit Expires On: 10/23/2016 Project Name: HABIT BURGER Owner: 2012 Name: KTM GROUP LLC Address: 2810 EASTLAKE AVE E , SEATTLE, WA, WA Cities Electrical Code: 98102 Contact Person: 2012 Name: ANDREW PAROLINE Address: 3617 SW CHARLESTOWN ST, SEATTLE, WA State Energy Code: WA, 98126 Contractor: 2012 Name: TUMYA PLUMBING CONTRACTOR, LLC Address: 5817 73 LN SW, OLYMPIA, WA, 98512 License No: TUMYAPC880JR Lender: Name: Date: Address: Phone: (206) 719-0339 Phone: (360) 878-0601 Expiration Date: 4/19/2018 DESCRIPTION OF WORK: INSTALL FLOOR DRAINS, VENT PIPES, WASTE LINES, SUPPLY LINES, GREASE TRAP, MOP SINKS, HAND WASHING SINKS, BACKFLOW PREVENTORS TOTAL FOUR (4) RPPAs ARE GOING TO BE INSTALLED. Valuation of Work: $19,750.00 Fees Collected: $455.14 Water District: TUKWILA Sewer District: TUKWILA SEWER SERVICE Current Codes adopted by the City of Tukwila: 71 International Building Code Edition: 2012 National Electrical Code: 2014 International Residential Code Edition: 2012 WA Cities Electrical Code: 2014 International Mechanical Code Edition: 2012 WAC 296-46B: 2014 Uniform Plumbing Code Edition: 2012 WA State Energy Code: 2012 International Fuel Gas Code: 2012 Permit Center Authorized Signature: Date: I hearby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances governing this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating construction or the performance of work. I am authorized to sign and obtain this development permit and agree to the conditions attached to this permit. Signature: Date: GLl'o?� " �/ (o Print Name: This permit shall become null and void if the work is not commenced within 180 days for the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. PERMIT CONDITIONS: 1: ***PLUMBING/GAS PIPING PERMIT CONDITIONS*** 2: No changes shall be made to applicable plans and specifications unless prior approval is obtained from the Tukwila Building Division. 3: All permits, inspection records and applicable plans shall be maintained at the job and available to the plumbing inspector. 4: All plumbing and gas piping systems shall be installed in compliance with the Uniform Plumbing Code and the Fuel Gas Code. 5: No portion of any plumbing system or gas piping shall be concealed until inspected and approved. 6: All plumbing and gas piping systems shall be tested and approved as required by the Plumbing Code and Fuel Gas Code. Tests shall be conducted in the presence of the Plumbing Inspector. It shall be the duty of the holder of the permit to make sure that the work will stand the test prescribed before giving notification that the work is ready for inspection. 7: No water, soil, or waste pipe shall be installed or permitted outside of a building or in an exterior wall unless, adequate provision is made to protect such pipe from freezing. All hot and cold water pipes installed outside the conditioned space shall be insulated to minimum R-3. 8: Plastic and copper piping running through framing members to within one (1) inch of the exposed framing shall be protected by steel nail plates not less than 18 guage. 9: Piping through concrete or masonry walls shall not be subject to any load from building construction. No plumbing piping shall be directly embedded in concrete or masonry. 10: All pipes penetrating floor/ceiling assemblies and fire -resistance rated walls or partitions shall be protected in accordance with the requirements of the building code. 11: Piping in the ground shall be laid on a firm bed for its entire length. Trenches shall be backfilled in thin layers to twelve inches above the top of the piping with clean earth, which shall not contain stones, boulders, cinderfill, frozen earth, or construction debris. 12: The issuance of a permit or approval of plans and specifications shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the Plumbing Code or Fuel Gas Code or any other ordinance of the jurisdiction. 13: The applicant agrees that he or she will hire a licensed plumber to perform the work outlined in this permit. 14: All new plumbing fixtures installed in new construction and all remodeling involving replacement of plumbing fixtures in all residential, hotel, motel, school, industrial, commercial use or other occupancies that use significant quantities of water shall comply with Washington States Water Efficiency ad Conservation Standards in accordance with RCW 19.27.170 and the 2006 Uniform Plumbing Code Section 402 of Washington State Amendments 15: The grease interceptor shall be installed per manufacturer's specifications. 16: RPPA backflows shall be installed per manufacturer's specifications. Upon installation all RPPAs shall be tested by a certified tester and passing backflow test reports submitted to Public Works Inspector. Thereafter RPPAs shall be tested on annual basis at owner's expense and backflow test reports forwarded to Tukwila Water Department, 600 Minkler Blvd, Tukwila, WA 98188, phone 206 433-1860, fax: 206 575- 3404. PERMIT INSPECTIONS REQUIRED Permit Inspection Line: (206) 438-9350 2000 GAS PIPING FINAL 8004 GROUNDWORK 1900 PLUMBING FINAL 9002 ROUGH -IN GAS PIPING 8005 ROUGH -IN PLUMBING 9001 UNDERGROUND CITY OF TUKW. Community Development Department Pernfit Center • 6300,5outheenter Blvd., .Suite 100 Tulovila, Tf7A 98188 http:Hww Nvj'uk\vilaWA. eov SITE LOCATION Plumbing/Gas rermit No. Project No. _ Date Application Accepted: _ Date Application Expires: W,I( (For office use on v) PLUMBING / GAS PIPING PERMIT APPLICATION Applications and plans must be complete in order to be accepted for plan review. Applications will not be accepted through the mail or by fax. **Please Print** King Co Assessor's Tax No.: Site Address: 17025 Southcenter Parkway Suite Number: Floor: l Tenant Name: Habit Burger New Tenant: ® .....Yes ❑ ..No PROPERTY OWNER Name: Metro Property Services Address: 2810 Eastlake Ave E City: Seattle State: WA zip: 98102 CONTACT PERSON — person receiving all project convrlunication Name: Andrew Paroline Address: 3617 SW Charlestown st City: Seattle State: WA Zip: 98126 Phone: (206) 719-0339 Fax: Email: andy@parolineassociates.com Valuation of Project (contractor's bid price): $. Scope of Work (please provide detailed information): 19,750 PLUMBING CONTRACTOR INFORMATION Company Name: TBD Address: City: State: Zip: Phone: Fax: Contr Reg No.: Exp Date: Tukwila Business License No.: Install floor drains, vent pipes, waste lines, supply lines, grease trap, mop sinks, hand washing sinks, backflow preventors per plan Building Use (per Int'l Building Code): Occupancy (per Int'1 Building Code): Utility Purveyor: Water: Tukwila 2012 M Sewer: Tukwila H:\Applications\Fomts-Applications On Line\2011 Applications\Plumbing Pemut Application Revised 8-9.1 Ldocs Revised: August 2011 Page I of 2 bh Indicate type of plumbing fixtures and/c is piping outlets being installed and the quantity- velow: Fixture Type Qty Bathtub or combination batlu/shower 1 Dishwasher, domestic with l independent drain 1 ShoNver, single head trap 1 Sinks 3 Rain water system — per drain (inside building) Grease interceptor for commercial kitchen (>750 gallon capacity) 1 Each additional medical 1 gas inlets/outlets greater than 5 Atmospheric -type vacuum breakers not included in laxvii sprinkler backflow protections (1-5 Fixture Type Qty Bidet Drinking fountain or water 1 cooler(per head) l Lavatory 1 Urinal 1 Water heater and/or vent 1 Repair or alteration of water piping and/or water treabnent equipment Backflow protective device other than abnospheric- 1 type vacuum breakers 2 1 inch (51 nun) diameter or smaller Atmospheric -type vacuum breakers not included in lawn sprinkler backflow rotections over 5 Fixtw•e Type Qty Clothes \vasher, domestic 1 Food -waste grinder, l commercial Wash fountain Water closet 1 Industrial waste treattnent interceptor, including trap and vent, except for kitchen type ease interceptors Repair or alteration of 1 drainage or vent piping Backflow protective device other than atmospheric -type vacuum breakers over 2 inch 51 111111) diameter Gas piping outlets 1 Fixture Type Qty Dental unit, cuspidor Floor drain 1 Receptor, indirect waste l Building sewer and each trailer park sewer Each grease trap 1 (connected to not more than 4 fixtures - <750 gallon capacity Medical gas piping system serving 1-5 inlets/outlets for a specific gas Each lawn sprinkler system on any one meter including backflow protection devices PERMIT APPLICATION NOTES - Value of Construction — In all cases, a value of constriction amount should be entered by the applicant. This figure will be reviewed and is subject to possible revision by the Pen -nit Center to comply with current fee schedules. Expiration of Plan Review — Applications for which no pernut is issued within 180 days following the date of application shall expire by limitation. The Building Official may grant one extension of time for an additional period not to exceed 180 days. The extension shall be requested in waiting and justifiable cause demonstrated. Section 103.4.3 International Plumbnig Code (current edition). I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE S,&&TE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING OWNER OR AUTHOR N Signature: a Print Name: Andrew Paroline Mailing Address: 3617 SW Charlestown ST Date: 02/12/2016 Day Telephone: (206) 719-0339 Seattle WA 98126 City State Zip 1-1:\Applioatioms\Forms-Applications On Line\2011 Applieations\Plumbing Permit Application Revised 8-9-1 Ldoex Revised: August 2011 Page 2 of 2 I'll Date Paid: Friday, July 08, 2016 Paid By: BRIAN WIGEN Pay Method: CREDIT CARD A61378 Printed: Friday, July 08, 2016 3:02 PM 1 of 1 (!rp SYSTEMS DESCRIPTIONS PermitTRAK ACCOUNT QUANTITY PAID $367.61 PG16-0017 Address: 17025 SOUTHCENTER PKWY Apn: 2623049070 $367.61 GAS $97.50 PERMIT ISSUANCE BASE FEE R000.322.100.00.00 0.00 $32.50 PERMIT FEE R000.322.100.00.00 0.00 $65.00 PLUMBING $252.60 PERMIT ISSUANCE BASE FEE R000.322.100.00.00 0.00 $32.50 PERMIT FEE R000.322.100.00.00 0.00 $220.10 TECHNOLOGY FEE $17.51 TECHNOLOGY FEE TOTALPAID BY RECEIPT:.. 307 R000.322.900.04.00 0.00 $17.51 $367.61 Date Paid: Tuesday, April 26, 2016 Paid By: TUMYA PLUMBING CONTRACTOR, LLC Pay Method: CHECK 5622 Printed: Tuesday, April 26, 2016 11:46 AM 1 of 1 (rr1/q(�1 SYSTEMS DESCRIPTIONS PermitTRAK PAID $1,382.94 D16-0040 Address: 17025 SOUTHCENTER PKWY Apn: 2623049070 $1,015.69 DEVELOPMENT $1,015.69 PLAN CHECK FEE R000.345.830.00.00 0.00 $1,015.69 EL16-0143 Address: 17025 SOUTHCENTER PKWY Apn: 2623049070 $152.03 ELECTRICAL $152.03 PLAN CHECK FEE R000.345.832.00.00 0.00 $152.03 M16-0027 Address: 17025 SOUTHCENTER PKWY Apn: 2623049070 $127.69 MECHANICAL $127.69 PLAN CHECK FEE R000.322.102.00.00 0.00 $127.69 PG16-0017 Address: 17025 SOUTHCENTER PKWY Apn: 2623049070 $87.53 GAS $24.38 PLAN CHECK FEE R000.322.103.00.00 0.00 $24.38 PLUMBING $63.15 PLAN CHECK FEE R000.322.103.00.00 TOTAL FEES ' .:: 0.00 $63.15 $1,382.94 Date Paid: Friday, February 12, 2016 Paid By: PAROLINE ASSOCIATES Pay Method: CREDIT CARD 712161 Printed: Friday, February 12, 2016 3:16 PM 1 of 1 CR SYSTEMS INSPECTION RECORD (q)r((0) Retain a copy with permit �Gj -" N-WSPN1L9"flN0. PERMIT N0. CITY OF TUKWILA BUILDING/�/WV4, P 6300 Southcenter Blvd., #100, Tukwila. WA 98188 / / `� , 3670!" '(� Permit Inspection Request Line (206) 438-9350/-,M Project: - Type of Inspection: b Inspector: C Date: �6; `( REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Address: �� o� 50,E Date Called: Special Instructions: 1 ate Want d: a.m. —71 "o O p.m. Requester: Phone No: Project: - Type of Inspection: b Inspector: C Date: �6; `( REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit INS CTION N0. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Project: Type -,of Inspection: Ad re s: / 7Q Z5 Date Called: Special Instructions: Date Wanted* �` a.m. (Q p.m. Requester: Phone No: Approved per applicable codes.a Corrections required prior to approval. COMMENTS: Inspector: Date: El REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit rG 4- ()o ( 71 INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Po' 991( f Type of Inspe ti@n: c / (0(j k(* Date Called: Special Instructions:ate r,41 Wanted- a.m. c .? " j(p p.m. I Requester: Phone No: ❑ Approved per applicable codes. El Corrections required prior to approval. Inspector Date: 7 (� REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd.. Suite 100. Calt to schedule reinspection. /"M INSPECTION RECORD Retain a copy with permijF6k6-W(7 t IN CTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Pr 'ecl f I V,(� TYPe of�n�s�pect n: � O e`od f� Acid : (0At V i Date Called: Special Instructions:at W t / a.m. r — p.m. Requester: Phone No: nApproved per applicable codes. l__J Corrections required prior to approval. Lt Inspector: Date:/ REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit 1 6_ �� I CTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Pr ec . 1�. Type of spectio Ac�lldsfeb' 5 r0 tr POLry ctte Called: Special Instructions: Dae W nted. r a.m. 0 p.m. Requester: Phone No: Approved per applicable codes. IRCorrections required prior to approval. REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. PG I& - 00 7. INSPECTION RECORD Retain a copy with permit I CTION N0. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 .1 Pt - Pr cr i Typ inspection. ,, Address: f 0� Sew �-1 V Dale Called: Special Instructions: � ' ACfate a� — � a.m. �(�j p.m. Requester: Phone No: (Inspector: 9 � IDate: �'- 2-3 —/Z REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. Cc*114- INSPECTION RECORD Retain a copy with permit I P6 16 �® 1 CTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 FlApproved per applicable codes. LJ Corrections required prior to approval. L IInspector: yr (Date: S-- fC(—l4 ❑ REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. 9, 12 INSPECTION RECORD Z Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Pr 'ect: Type of Inspection: "bit- 6 fl 14')a Address:L �� ate Catl . O Z� 6 tC Special Instructions: 0 to Want a.m. —1 p.m. Requester: Phone No: Approved per applicable codes. UCorrections required prior to approval. COMMENTS: O h r vc— W/ H-7 —o 12 rso- a - C-"!-< L , a A LOC'_. rtj SLI r o if" Lt/Or I- I a IIn5I7pCtOr: �UdCe,�— ❑ REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit If(, lb -00(7 I PECTION N0, PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Pr j ct:. fib' Type of Inspection: � r- r Address: 7®L SUI W -fv PY Kw Date Call Special Instructions: DatWanted: a.m. _ -13 / p.m. Requester. X04 Ph e '>6o -- Q (inspector: f-� I Date: / � _ / b REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. FREDERICK J. GOGLIA ARCHITECT, NCARB, ISP June 28, 2016 CORREC ION City of Tukwila LTR# Department of Community Development KE"16`10N 01 Attn: Mr. Bill Rambo 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 PFAW RECEIV*-D Ph: 206-431-3670 rILLA CITY OF TU KWILA RE: Habit Burger JUN 3o 2016 Plumbing/Gas Piping Permit Application Number PG 16-0017 17025 Southcenter Pkwy Tukwila, WA PERMIT CENTER ArcV Project: 150684 This letter is in response to the comments dated June 17th, 2016. Please find below the comments and their respective responses. (General note) Plan Submittals: (Min. size 11 x1 7 to maximum size of 2436; all sheets to be the same size. New revised plan sheets shall be the same size sheets as those previously submitted). (If applicable) "STAMP and SIGNATURES" "Every page of a plan set must contain the seal/stamp, signature of the licensee(s) who prepared or who had direct supervision over the preparation of the work, and date of signature. Specifications that are prepared by or under the direct supervision of a licensee shall contain the seal/stamp, signature of the licensee and the date of signature. If the "specifications" prepared by a licensee are a portion of a bound specification document that contains specifications other than that of an engineering or land surveying nature, the licensee need only seal/stamp that portion or portions of the documents for which the licensee is responsible." It shall not be required to have each page of "specifications" (calculations) to be stamped and signed; Front page only will be sufficient. (WAC 196-23-010 & 196-23-020. (Building Review Notes) 1. The revision shows a new sump pump installation where it shall be pumping to another sump pump located down line of this proposed pump installation. Provide sizing calculations with manufacturers installation and specification for the new pump to include sizing specifications of the downstream pump to verify that the downstream pump shall be sufficient to handle the total demand of the new pump with any other fixtures connected to this drain system. Response: Plumbing drawing P200 has been updated with the requested pump sizing information. The existing sewage ejector pump serving the Habit Burger tenant space also serves the balance of the tenant spaces in both the north and south buildings. That pump system (wet well, twin ejector pumps, controller and discharge to the public sewer system) is owned, operated and maintained by the landlord of the shopping center. We have advised the landlord and the maintenance contractor the landlord employs to oversee the operation of the pump system (Utilities Service Company — of the sewage flow generated by Habit Burger (56.34 GPM maximum) and they have not notified ArcVision that their system will be adversely impacted by that sewage flow. It is our understanding that they have concluded that their system is capable of accepting and discharging Habit Burger's 1950 Craig Road Suite 300 • St. Louis, MO 63146-4106 • Phone (314) 415-2400 • Fax (314) 415-2300 sewage flow, in addition to all other flows from tenants served by the system without issue. PW - PG DEPARTMENT: Joanna Spencer - 206-431-2440 1. Applicant or owner shall fill out attached King County Non -Residential Sewer Use Certification form. Please list all the new plumbing fixtures to be installed. Do not list the fixtures to be replaced in kind. Back page of your permit application is attached for reference. Response: See attached filled out form. 2. Submit pump cut sheet and spec including pump maintenance requirements. Response: See attached cut sheets. If you have any questions, comments or need any additional information regarding this letter please contact Julia Test at our office at any time (817) 391-3970. Sincerely, Frederick J. Gogl' Architect, NCARB, ISP CC: File J:\Clients\Zales\ 140649\Docs 1950 Craig Road Suite 300 • St. Louis, MO 63146-4106 * Phone (314) 415-2400 9 Fax (314) 415-2300 rILM TiG[&-cot7 ,g County ,partment or Naturai Resources and Parks Iastewater Treatment Division ,on -Residential aewer Use Certification e To be completed for all new sewer connections, reconnections or change of use of existing connections. o This form does not apply to repairs or replacements of existing sewer connections within five years of disconnect. Please Print or Type Property Street Address ilk 11 City Stare ZIP _— owners Name Subdivision Name Lot # Subdiv. #—___ Block # Building Name FAA & Vt �1.tt � (it applicable) 0 Owners Phone Number (with Area Code) P_.�..c) �.. - Prapraty contact prone umber (will Area Coda) Owner's Mailing Address A. Fixture units Fixture Units x Number of Fixtures = Total Fixture Units Kind of Fixture ^^� Pixtum Ueda Public Private No, of Amos Public Private fbtture units Bathtub and Shower 4 4 _ Shower, per head 2 2 Dishwasher 2 2 Drinking fountain (each head) 1 .5 Hose bibb (interior) 2.5 1 2.5 Clotheswasher or laundry tub 4 2 Sink, bar or lavatory 2 1 Sink, Clinic flushing 8 8 _ Sink, kitchen 3 2 _Sink, other (service) 3 1.5 _ Slnk, witsh fountain, circle spray 4 3 Urinal, flush valve,1 GPF 5 2 ; Urinal, flush valve, >1 GPF 6 2 Urinal, waterless 0 0 Water closet, tank or valve, 1.6 GPF 6 3 t Water closer, tank or valve, >1.6 GPF 8 4 Total Fixture Units Les a,-,, I Residential Customer Equivalent (RCE) 20 fixture units equal 1.0 RCE Total No. of Fixture Units = i1 RCE 20 EFor King County Use Only Account # No. of RCEs Monthly Rate Property Tax ID Party to be Billed (If different from owner) City or Sewer District ^i) w1,1A Date of Connection Side Sewer Permit # Please report any demolitions of preexisting building on this property. Credit for a demolition may be given under some circumstances. Demolition of pre-existing building? OYes PlNo Was building on Sanitary Sewer? gYos O No Was Sewer connected before 211/90? RYes O No Sewer disconnect date: Type of building demolished?- Request emolished? Request to apply demolition credit to multiple buildings? O Yes No B. poser Wastewater Flow (in addition to Fixture Units identified in Section A) Type of Facility/Process: i T �'.ORRCTIQN Estimated Wastewater Discharge: LTR# Gallons/days Residential Customer Equivalents (RCE): 187 gallons per day equals 1.0 RCE Total Discharge (gal/day) ` RCE 187 C. Total Residential Customer Equivalents: (add A & B) RECEIVED A CiTY OF TUKWILA } B JUN 30 2016 RCE PERMIT CENTER Pursuant to King County Code 28.84, all sewer customers who establish a new service which uses metropolitan sewage facilities shall he subject to a capacity charge, The amount of the charge is established annually by the kng tpurity Council at a rate per month per residential customer or residential customer equivalent for a period of fifteen years. The purpose of the charge is to reCoVer costs of providing sewage treatment capacity for new sewer customers. All future billings can be prepaid at a discounted amount. All future billings can be prepaid at a discounted amount. Questions regarding the capacity charge or this form should be referred to Ming County's Wastewater Treatment Division at 206-684.1740. l certify that the information given is correct. l understand that the capacity charge levied will be based on this information and any deviation will require resubmission of corrected data for determination of a revised capacity charge. Signature of OwnerlRepresentative Date Print Name of Owner/Representative _ io69 (nev, 9!4)7) white — Kinn Couniv Yellow — Local Sewer Aaenev Pink— Sewer cusromer , k-aKing County _PG I„ ` O0 Department of Natural Resources and Parks Wastewater Treatment Division Non -Residential Sewer Use Certification • To be completed for all new sewer connections, reconnections or change of use of existing connections. • This form does not apply to repairs or replacements of existing sewer connections within five years of disconnect. Please Print or Type Property Street Address -1441wi % City State ZIP 509 �� Z LG Owner's Name Subdivision Name Subdiv Building Name Lot # Block # (if applicable) Owner's Phone Number (with Area Code) c2alo ) 41oa OS4 � Property Contact Phone Number (with Area Code) J Owner's Mailing Addre � 14, A. Fixture Units Fixture Units x Number of Fixtures = Total Fixture Units Kind of Fixture Fixture Units Public Private No. of Fixtures Total Public Private Fixture units Bathtub and Shower 4 4 Q Shower, per head 2 2 lj Dishwasher 2 2 Drinking fountain (each head) 1 .5 Hose bibb (interior) 2.5 1 2.5 Q Clotheswasher or laundry tub 4 2 Sink, bar or lavatory 2 1 Sink, Clinic flushing 8 8 Sink, kitchen 3 2 Sink, other (service) 3 1.5 Z Sink, wash fountain, circle spray 4 1 3 Urinal, flush valve, 1 GPF 5 2 / f Urinal, flush valve, >1 GPF 6 2 Urinal, waterless 0 0 Q Water closet, tank or valve, 1.6 GPF 6 3_3 3 Water closet, tank or valve, >1.6 GPF 8 4 Total Fixture Units % 1 Residential Customer Equivalent (RCE) 20 fixture units equal 1.0 RCE Total No. of Fixture Units = RCE 20 For King County Use Only Account # No. of RCEs Monthly Rate Property Tax ID # N77 Party to be Billed (if different from owner) City or Sewer District /{e,4 Date of Connection IvA Side Sewer Permit # Please report any demolitions of pre-existing building on this property. Credit for a demolition may be given under some circumstances. Demolition of pre-existing building? ❑ Yes CI No Was building on Sanitary Sewer? Fles ❑ No Was Sewer connected before 2/1/90? ❑ Yes ❑ No Sewer disconnect date: Type of building demolished?_ AI Request to apply demolition credit to multiple buildings? ❑ Yes ❑ No B. Other Wastewater Flow (in addition to Fixture Units identified in Section A) Type of Facili_ty//�P�r/o�cess: Estimated Wastewater Discharge: Gallons/days Residential Customer Equivalents (RCE): 187 gallons per day equals 1.0 RCE Total Discharge (gal/day) _ RCE 187 C. Total Residential Customer Equivalents: (add A & B) AD B _ RCE .SUN 24 20% PERMNT Pursuant to King County Code 28.84, all sewer customers who establish a new service which uses metropolitan sewage facilities shall be subject to a capacity charge. The amount of the charge is established annually by the King County Council at a rate per month per residential customer or residential customer equivalent for a period of fifteen years. The purpose of the charge is to recover costs of providing sewage treatment capacity for new sewer customers. All future billings can be prepaid at a discounted amount. All future billings can be prepaid at a discounted amount. Questions regarding the capacity charge or this form should be referred to King County's Wastewater Treatment Division at 206-684-1740. 1 certify that the information given is correct. I u derstand that the capacity charge levied will be based on this information and any deviation will require resubmission of corre d data for determination of a revised capacity charge. Signature of Owner/Representative ,)Date Print Name of Owner/Representati 1058 (Rev. 9/07) White — Kino Countv Yellow — Local Sewer Aoencv Pink — Sewer Customer .c�agimxM ` "' R 12 SUBMERSIBLE GRINDER PUMP I � F 1 -- -7, , - F--- I�� lb -0017 TECHNECAL BROCHURE BRGS2012 R3 CORREG LTR#= I xylem branl� Wastewater FEATURES Design: Capable of grinding domestic sewage in individual residential applications. Cutter System: Anti -roping design. Two blade rotary cutter is threaded to shaft. Stationary cutter ring is reversible for extended service. Impeller: Silicon bronze, semi -open, non -overloading two -vane design with pump -out vanes for mechanical seal protection. Balanced for smooth operation. Casing: Cast iron, volute type for high efficiency. Adaptable for guide rail system. Motor: Fully submerged in oil -filled chamber. High grade turbine oil surrounds motor for more efficient heat dissipation, permanent lubrication of bearings and mechanical seal, and protection against outside environment. Motor Shaft: 300 series stainless steel, short overhang for minimum shaft deflection. Designed for Continuous Operation: Pump ratings are within the motor manufacturer's recommended working limits, can be operated continuously without damage when fully submerged. Designed for high head residential sewage applica- tions where a gravity system is not practical. Ideal for pressure sewage systems. Pump: • Capacities: to 41 GPM • Total heads: to 95' TDH • Discharge: 1%" NPT • Temperature: 104°F (40'C) maximum continuous, 140°F (60°C) maximum intermittent • Single mechanical seal: silicon carbide rotary/silicon carbide stationary, 300 series stainless steel metal parts, BUNA-N elastomers • Fasteners: 300 series stainless steel • Rotating cutter and cutter ring: 440 C hardened stainless steel PHG 2 BE Bearings: Upper and lower ball bearings for precision positioning of parts and to carry all radial and thrust loads. Mechanical Seal: Hardfaced Silicon carbide for longer life, stainless steel metal parts, BUNA-N elastomers. Power Cable: Severe duty rated, oil and water resistant. Epoxy seal on motor end provides secondary moisture barrier in case of outer jacket damage and to prevent oil wicking. O -Ring: Assures positive sealing against contaminants and oil leakage. Paint: Electro -coat paint process protects all casting surfaces. May be used with optional guide rail. See Fittings or Pump Removal Systems. AGENCY LISTINGS Q Tested to UL 778 and CSA 22.2 108 Standards By Canadian Standards Association File #LR38549 (UD Underwriters Laboratories Motor: • Single phase: 2 HP, 60 Hz, 3450 RPM, 208/230 V, capacitor start with on winding thermal protector. No external capacitor kits required. • Class F insulation • Shaft: 300 series stainless steel threaded design • Bearings: ball bearings upper and lower Power Cord with bare lead ends: • Use for connections in a control panel or junction box • Standard length 20', 14/3 STOW • Optional lengths of 30', 50' and 100' Power Cord with 230 V NEMA three prong grounding plug: • P suffix equals a 20' long cord with plug • PS suffix equals a 30' long cord with plug • Allows direct connection to piggyback type float switch Im Wastewater METERS FEET NP Volts Phase 110 Operation Discharge Impeller Diameter Maximum MODEL: RGS2012 Power Cord Weight Number DiSCH: 1V/4" NPT 3450 15 � SPEED: 3450 RPM Size 30 100 �-, `` (lbs.) 90 "t 208/230 25 3450 Manual 1 r/" 5.69" 80 59 20' with Bare Leads 75 70 20' with 230 V Plug 20 20' with 230 V Plug a Automatic 40 s and Float 76 RGS2012PS Manual 30' with 230 V Plug O 15 50 40, 10 30 20 5 10 0 00 U.S. 5 10 15 20 25 30 35 40 45 GPM 0 2.5 5.0 7.5 10.0 m -/hr CAPACITY = A 11/4" minimum discharge pipe requires a minimum flow of 10 gpm to maintain a 2 ft./sec. scouring velocity. Flows less than 10 gpm will allow solids to settle in the pipe. MODEL INFORMATION Order NP Volts Phase RPM Operation Discharge Impeller Diameter Maximum LRA Power Cord Weight Number 1 3450 15 59 70 Size (inches) Amps (lbs.) RGS2012 "t 208/230 1 3450 Manual 1 r/" 5.69" 15 59 20' with Bare Leads 75 RGS2012P 20' with 230 V Plug 20' with 230 V Plug RG52012PA Automatic and Float 76 RGS2012PS Manual 30' with 230 V Plug A non -stock pump may be special ordered with optional legs by adding an "L" suffix to the Order Number. Example: RGS2012L, RGS2012SL, RGS2012PSL, etc. See "L" List Adder in price book. MOTOR DATA HP Volts Phase RPM Maximum Amps P LRA Full Load Motor Efficiency cY Resistance Power Cable Fuse/ Circuit Breaker Start Line -Line 2 208/2.30 1 3450 15 59 70 2.47 1.1 14/3 30 PAGF3 APPLICATION DATA Minimum Casing Thickness -/j 6 Casing Corrosion Allowance ''/h" Maximum Working Pressure 50 PSI Maximum Submergence 50 feet Minimum Submergence Fully submerged for continuous operation 6 " below top of motor for intermittent operation Maximum Environmental Temperature 40°C (104°F) continuous operation 60°C (140°F) intermittent operation Maximum Number of Evenly Distributed Starts per hour 10 Bearings B-10 life of 30,000 hours min. Minimum Basin Size Simplex - 24" x 36" Fiberglass Duplex - 36" z 36" Fiberglass 1'/a" Minimum Discharge Pipe Diameter Requires a minimum flow of 10 gpm to maintain a 2 ft./sec. scouring velocity 2" Maximum Discharge Pipe Diameter Requires a minimum flow of 21 gpm to maintain a 2 ft./sec. scouring velocity Ball Bearing - upper Single row ball - SKF 6203-2Z Ball Bearing - lower Single row ball - SKF 6204-2Z Mechanical Seal Silicon carbide/silicon carbide; Type 16 O -Ring - motor cover BONA -N, AS 568A-166 WOMMIUMMM Pov;e-Cable -type 14/3 STOW, single phase with bare leads 14/3 STOW, with 230 V NEMA three prong grounding plug Motor Cover _ Gray cast iron - ASTM A48, Class 30 Bearing Housing Gray cast iron - ASTM A48, Class 30 Seal Housing Gray cast iron - ASTM A48, Class 30 Casing _ Gray cast iron - ASTM A48, Class 30 Impeller Cast silicon bronze - ASTM B584 C87600 Motor Shaft AISI 300 series stainless steel Motor Design NEMA 48 frame, oil filled with Class F insulation Motor Overload Protection On winding thermal protector - auto reset External Hardware 300 series stainless steal Impeller Type Semi -opened with pump out vanes on back shroud Cutter i Two blades; type 440C hardened stainless steel Oil Capacity - motor chamber 88 gallons CUTTER R ASSEM Y 2 -Blade Rotating Cutter DIMENSIONS (All dimensions are in inches. Do not use for construction purposes.) %a 1'/a NPT 8%a I yi DISCHARGE i 18'/2 �j i b''h *Optional pump legs are recommended for poly or fiberglass basin STAN- 3%z I installations where the pumps contact the basin floor. The order DAR D 3 i. number for a package of (3) three optional pump legs is 4K639. FEET -..... xylem Let's Solve Water Xylem Inc. 2881 East Bayard Street Ext., Suite A Seneca Falls, NY 13148 Phone: (866) 325-4210 Fax: (888) 322-5877 www.gouldswater-tech nology.corn i_ a rec,tere,i trac evidrk of GouHs Pumps, Inc. a,-, is k_ .^ ;mcler P-er; 2C16 Xylen Inc Bi GS%''12 R.? , 2J16 Reversible Cutter Ring , Wastewater Pump/ Control Kit Order No. Description Simplex SIMRGSKTN4* (1) RGS2012 2HP, 230 V, single phase, pump (1)S10020 Simplex outdoor control panel (3) A2D23W Mechanical level switch 41<639 Cast iron pump leg (set of 3) Duplex DUPRGSKTN4* (2) RGS2012 2 HP, 230 V, single phase, pump ! oF•eerKv�pawab (3) A2D23W Mechanical level switch 30 41<639 Cast iron pump leg (set of 3) * For indoor panel delete suffix "N4", SIMRGSKT includes a S1 0020N1 panel. DUPGRSKT includes a D10020N1 panel. PUMP AND CONTROL DATA GRINDER PUMP PACKAGES A complete simplex or duplex installation consists of a simplex or duplex pump kit AND a simplex or duplex basin kit. Choose the simplex or duplex basin kit from the chart on the following pages to best suit your installation needs and make sure it is included in your order. Both pump/control kit and basin kit must be ordered for a complete, installation. Component HP Volts Phase RPM Maximum Amps LRA Full Load Resistance Power Motor Efficiency Start Line -Line Cable Fuse/Weight Circuit Breaker (lbs.) RGS2012 2 208/230 1 3450 15 59 70 2.47 1.1 14/3 30 75 S10020 Simplex Outdoor N4X Panel 20 Maximum Amps S10020N1 Simplex Indoor N1 Panel 20 Maximum Amps D10020 Duplex Outdoor N4X Panel 20 Maximum Amps D100201\11 Duplex Indoor N1 Panel 20 Maximum Amps METERS FEET MODEL: kb5412 I OISC.H: 1 '1.` NPT t ,'.=PEED: 3450 RPM 30 100 ..........� 90 23 ^3¢. 80 a B eD 10 20 s 10 o 04 _ 0 1L- s :7 nx <;- Ss a=, :a U.S. GPM 0 2.5 L0 )S CAPACITY —j A 114" minimum dl"heq. pipe r.q.ir>. a m:-.imum Sow of 10 gpm to -;ma a 2 (IJ—'.' '-'mg -1-ity. Flows Icf .hen 10 gpm will 4— solids:. settle in the Pipe. PAGE 2 TYPICAL INSTALLATION SOLID FIBERGLASS COVER 3" NPTTHREADED VENT FLANGE FIELD INSTALLED 304 STAINLESS STEEL FLOAT BRACKET WITH (3) GRIPS 1 %z" ELECTRICAL GROMMET WITH I h" PVC PIPE ELEV 4" INLET GROMMET FIELD INSTALLED INV. ELEV I$1 HIGH ELEV IF LEVEL ELEV ALARM qi-........ PUMP UN ELEV PUMP OFF ELEV V FIBERGLASS ANTI -FLOAT ROUND FLANGE BRASS QUICK DISCONNECT GATE VALVE W7x19 STAINLESS STEEL LIFTING CABLE V 304 STAINLESS STEELVALVE EXTENSION HANDLE INDUSTRIAL ENAMELED STEEL DISCHARGE COUPLING 4 INV. ELEV BALLCHECK VALVE DISCHARGE PIPE \\\ CAST FF:ON PUMP LEGS V Wastewater BASIN KIT (Each, pump kit requires one of the following basin kits to complete the Residential Pump Package.) * Basins are not pre -drilled for 1.5" electrical grommet or for 4" inlet grommet. Parts are shipped loose. Installer must drill holes for grommets. Guide Rail Equipped Basin Installation (pump is suspnded-by.its discharge) Simplex Duplex , • 24" diameter fiberglass basin with integral anti- • 36dia eter fiberglass basin with integral anti - floatation ring. floatation ring. • Stainless steel hardware. • Grass green solid fiberglass cover. • 1.5" electrical grommet. • 4" inlet grommet. * • Brass quick disconnect coupling. • Schedule 40 galvanized steel discharge pipe. • Cast iron ball type check valve. • Bronze gate valve. • %4" stainless steel pump lifting cable • Pump slide rail system complete with PVC guide pipe and integral stainless steel guide bracket for those installations requiring a guide rail type system s "M Ve S4UGR48 Kit No Discharge Piping (SS) Slide Rail Basin Dia. Basin Depth "A" Dim. 54UGR48 1.25" Stainless 24" 48" (tall) 20" steel guide bracket and S4UGR84 1.25" PVCp gueide 24" 84" (tall) 42" Pipe • Stainless steel hardware. • Grass green solid fiberglass cover. • 1.5" electrical grommet. • 4" inlet grommet * • (2) Brass quick disconnect couplings. • Schedule 40 galvanized steel discharge pipes. • (2) Cast iron ball type check valves. • (2) Bronze gate valves. • (2) 1/4" stainless steel pump lifting cables. • Pump slide rail system complete with dual pipe stainless steel guide rail system assembly for those installations requiring a guide rail type system. Kit No. Discharge Piping (SS) Slide Rail Basin Dia. Basin I Depth "A" Dim. D4UGR48 1.25" Stainless 36" 48" (tall) 20" steel guide bracket and D4UGR84 1.25" PVC guide 36" 84" (tall) 42" Pipe 'Ba IIj PAGE 3 FILE TECHNICAL BROCHURE BRGS2012 REVIEWED FOR CODE COMPLIANCE APPROVED JUL 01 2016 Q Ci of Tukwila BUILDING DIVISION REVISION NO, . 'I ^:. - 12 ,.. mss, 0 CORRECTION SUBMERSIBLE GRINDER PUMP LTR# --J—, RECEIVED CITY OF `I`UKWILA JUN 2 4 2016 PERMIT CENTER GOU LDS G1 6... oo 1 40 ZVER TECHNOLOGY 7 a xylem brand Wastewater FEATURES Design: Capable of grinding domestic sewage in individual residential applications. Cutter System: Anti -roping design. Two blade rotary cutter is threaded to shaft. Stationary cutter ring is reversible for extended service. Impeller: Silicon bronze, semi -open, non -overloading two -vane design with pump -out vanes for mechanical seal protection. Balanced for smooth operation. Casing: Cast iron, volute type for high efficiency. Adaptable for guide rail system. Motor: Fully submerged in oil -filled chamber. High grade turbine oil surrounds motor for more efficient heat dissipation, permanent lubrication of bearings and mechanical seal, and protection against outside environment. Motor Shaft: 300 series stainless steel, short overhang for minimum shaft deflection. Designed for Continuous Operation: Pump ratings are within the motor mandfacturer's recommended working limits, can be operated continuously without damage when fully submerged. APPLICATIONS Designed for high head residential sewage applica- tions where a gravity system is not practical. Ideal for pressure sewage systems. SPECIFICATIONS �::a i,tiac Pump: • Capacities: to 41 GPM • Total heads: to 95' TDH • Discharge: 1'/4" NPT • Temperature: 104°F (40°C) maximum continuous, 140°F (60°C) maximum intermittent • Single mechanical seal: silicon carbide rotary/silicon carbide stationary, 300 series stainless steel metal parts, BUNA-N elastomers • Fasteners: 300 series stainless steel • Rotating cutter and cutter ring: 440 C hardened stainless steel per= 1) Bearings: Upper and lower ball bearings for precision positioning of parts and to carry all radial and thrust loads. Mechanical Seal: Hardfaced Silicon carbide for longer life, stainless steel metal parts, BUNA-N elastomers. Power Cable: Severe duty rated, oil and water resistant. Epoxy seal on motor end provides secondary moisture barrier in case of outer jacket damage and to prevent oil wicking. O -Ring: Assures positive sealing against contaminants and oil leakage. Paint: Electro -coat paint process protects all casting surfaces. May be used with optional guide rail. See Fittings or Pump Removal Systems. AGENCY LISTINGS C• Tested to UL 778 and CSA 22.2 108 Standards By Canadian Standards Association us File #LR38549 ULUnderwriters Laboratories Motor: • Single phase: 2 HP, 60 Hz, 3450 RPM, 208/230 V, capacitor start with on winding thermal protector. No external capacitor kits required. • Class F insulation • Shaft: 300 series stainless steel threaded design • Bearings: ball bearings upper and lower Power Cord with bare lead ends: • Use for connections in a control panel or junction box • Standard length 20', 14/3 STOW • Optional lengths of 30', 50' and 100' Power Cord with 230 V NEMA three prong grounding plug: • P suffix equals a_ 20' long , Mrd with plug • PS suffix equals a 30' long cord withplug f -Allows direct connection to piggyback type float switch METERS FEET 1 d 20 10 5 0 2.5 5.0 7.5 10.0 m3/hr CAPACITY = A 11/4" minimum discharge pipe requires a minimum flow of 10 gpm to maintain a 2 ft./sec. scouring velocity. Flows less than 10 gpm will allow solids to settle in the pipe. MODEL INFORMATION Order HP Volts Phase RPM Operation Discharge Impeller DiameterMaximum Fuse/ Circuit Breaker 1 LRA Power Cord Weight Number 1 3450 15 59 70 2.47 Size (inches) Ams (lbs.) RGS2012 2 208/230 1 3450 Manual 11/4" 5.69" 15 59 20' with Bare Leads 75 RGS2012P 20' with 230 V Plug RGS2012PA Automatic 20'with Plug and Float 76 RGS2012PS Manual 30' with 230 V Plu A non -stock pump may be special ordered with optional legs by adding an "L" suffix to the Order Number. Example: RGS2012L, RGS2012SL, RGS2012PSL, etc. See "L" List Adder in price book. MOTOR DATA HP Volts Phase RPM Maximum Amps LRA Full Load Motor Efficiency. Resistance Power Cable Fuse/ Circuit Breaker 1 Start Line -Line 2 208/230 1 3450 15 59 70 2.47 0.6 14/3 30 aer.F z APPLICATION DATA Minimum Casing Thickness %4" Casing Corrosion Allowance Ys" Maximum Working Pressure 50 PSI Maximum Submergence 50 feet Gray cast iron - ASTM A48, Class 30 Fully submerged for continuous Minimum Submergence operation 6" below top of motor for Motor Shaft AISI 300 series stainless steel intermittent operation Maximum Environmental 40°C (104°F) continuous operation Temperature 60°C (140°F) intermittent operation Maximum Number of Evenly 10 Distributed Starts per hour Cutter Bearings B-10 life of 30,000 hours min. Minimum Basin Size Simplex - 24" x 36" Fiberglass Duplex- 36" x 36" Fiberglass 11/4" Minimum Discharge Requires a minimum flow of Pipe Diameter 10 gpm to maintain a 2 ft./sec. scouring velocity 2" Maximum Discharge Requires a minimum flow of 21 gpm to maintain a 2 ft./sec. Pipe Diameter scouring velocity STANDARD PARTS Ball Bearing - upper Single row ball - SKF 6203-2Z Ball Bearing - lower Single row ball - SKF 6204-2Z Mechanical Seal Silicon carbide/silicon carbide; Type 16 O -Ring - motor cover BUNA-N, AS 568A-166 DIMENSIONS (All dimensions are in inches. Do not use for construction purposes.) 181/2 Q 11/4 NPT F DISCHARGE STAN- DARD FEET lem Lets Solve Water CONSTRUCTION DETAILS Power Cable - type 14/3 STOW, single phase with bare leads 14/3 STOW, with 230 V NEMA three prong grounding plug Motor Cover Gray cast iron - ASTM A48, Class 30 Bearing Housing Gray cast iron - ASTM A48, Class 30 Seal Housing Gray cast iron - ASTM A48, Class 30 Casing Gray cast iron - ASTM A48, Class 30 Impeller Cast silicon bronze - ASTM 8584 C87600 Motor Shaft AISI 300 series stainless steel Motor Design NEMA 48 frame, oil filled with Class F insulation Motor Overload Protection On winding thermal protector - auto reset External Hardware 300 series stainless steel Impeller Type Semi -opened with pump out vanes on back shroud Cutter Two blades; type 440C hardened stainless steel Oil Capacity - motor chamber .88 gallons CUTTER ASSEMBLY 2 -Blade Rotating Cutter 14D 61/2 * Optional pump legs are recommended for poly or fiberglass basin installations where the pumps contact the basin floor. The order number for a package of (3) three optional pump legs is 4K639. Xylem, Inc. 2881 East Bayard Street Ext., Suite A Seneca Falls, NY 13148 Phone: (866) 325-4210 Fax: (888) 322-5877 www.xyleminc.com/brands/gouldswatertechnology Goulds is a registered trademark of Goulds Pumps, Inc. and is used under license. 0 2012 Xylem Inc. BRGS2012 March 2012 Reversible Cutter Ring I i Standard Optional Foot Pump Legs Order No. 4K639 (Set of 3) FILE REVISION,No.,�--L. INSTRUCTION MANUAL IM038R06 REVIEWED FOR CODE COMPLIANCE APPROVED JUL 01 2016 Ci f Tukwila BUILD G DIVISION CORRECTION LTR#_--�._, i n g,,j.e.,-P-h ase i n g I e .4 eaGri*nder-Pump INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS 6-,4-0017 RECEIVED CITY OF TUKWILA JUN 24 2016 PERMIT CENTER GOULDS WATER TECHNOLOGY a xylem brand Table of Contents SUBJECT PAGE SafetyInstructions........................................................................................................................................................3 Pre -Installation Checks.................................................................................................................................................3 Liftingof Pump............................................................................................................................................................ 3 Optional Guide Rail or Lift -Out System...................................................................................................................... 3 Piping........................................................................................................................................................................... 4 Wiringand Grounding................................................................................................................................................. 4 Selecting and Wiring Pump Control Panels and Switches ...........................................................................................4-5 Installation................................................................................................................................................................... 5 Operation.................................................................................................................................................................. 5-6 FloatSwitch and Panel Chart...................................:.................................................................................................... 6 EngineeringData..................................:.......................................................................................................................7 Insulation Resistance Readings..................................................................................................................................... 8 Typical Installations and Simplex Wiring Diagrams....................................................................................................8-9 Troubleshooting.........................................................................................................................................................10 LimitedWarranty.................:.....................................................................................................................................11 Pump Model Number: Pump Serial Number: Control Model Number: Dealer - Dealer Phone No. Date of Purchase: Installation: Current Readings at Startup: 10 Amps: Volts: t 6 �"r SAFETY INSTRUCTIONS TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR MAJOR PROPERTY DAMAGE, READ AND FOLLOW ALL SAFETY INSTRUCTIONS IN MANUAL AND ON PUMP. THIS MANUAL IS INTENDED TO ASSIST IN THE INSTALLATION AND OPERATION OF THIS UNIT AND MUST BE KEPT WITH THE PUMP. This is a SAFETY ALERT SYMBOL. When you see this symbol on the pump or in the manual, look for one of the fol- lowing signal words and be alert to the potential for personal injury or property damage. . • Warns of hazards that WILL cause serious personal injury, death or major property damage. AWARNING Warns of hazards that CAN cause serious personal injury, death or major property damage. Warns of hazards that CAN cause per- sonal injury or property damage. NOTICE: INDICATES SPECIAL INSTRUCTIONS WHICH ARE VERY IMPORTANT AND MUST BE FOLLOWED. THOROUGHLY REVIEW ALL INSTRUCTIONS AND WARNINGS PRIOR TO PERFORMING ANY WORK ON THIS PUMP. MAINTAIN ALL SAFETY DECALS. AWARNING All electrical work must be performed by a qualified technician. Always follow the National Electrical Code (NEC), or the Canadian Electrical Code, as well as all local, state and provincial codes. Code questions should be directed to your local electrical inspector. Failure to follow electrical codes and OSHA safety standards may result in personal injury or equipment damage. Failure to follow manufacturer's installation instructions may result in electrical shock, fire hazard, personal injury or death, damaged equipment, provide unsatisfactory performance, and may void manu- facturer's warranty. AWARNING Standard units are not designed for use in swimming pools, open bodies of water, hazardous liquids, or where flammable gases exist. These fluids and gases may be present in containment areas. Tank or wetwell must be vented per local codes. Only pumps specifically Listed for Class 1, Division 1 are allowable in hazardous liquids and where flammable gases may exist. See specific pump catalog bulletins or pump nameplate for all agency Listings. AWARNING Disconnect and lockout electrical power before installing or servicing any electrical equipment. Many pumps are equipped with automatic thermal overload protection which may allow an over- heated pump to restart unexpectedly. Open all cartons and inspect for shipping damage. Report any damage to your supplier or shipping carrier immedi- ately. Important: Always verify that the pump nameplate Amps, Voltage, Phase, and HP ratings match your control panel and power supply. Many of our sewage pumps are oil -filled. If there are any signs of oil leakage or if the unit has been stored for an extended period check the oil level in the motor dome and the seal housing, if so equipped. Check the motor cover oil level through the pipe plug on top of the unit. The motor chamber oil should just cover the motor. Do not overfill, leave room for expansion! If low, refill with an ASTM 150 turbine oil. Replace the plug. Oil is available in 5 gallon cans through our distributors. You can also source oil locally at motor repair shops. Typical oil brands are: Shell Turbo 32, Sunoco Sunvis 932, Texaco Regal R&O 32, Exxon Nuto 32 and Mobil DTE Light. Check the strain relief nut on power cable strain assem- blies. Power cables should be torqued to 75 in. lbs. for #16 cables and 80 in. lbs. for all other cable assemblies. Warranty does not cover damage caused by connecting pumps and controls to an incorrect power source (volt- age/phase supply). Record the model numbers and serial numbers from the pumps and control panel on the front of this instruction manual for future reference. Give it to the owner or affix it to the control panel when finished with the installation. AWARNING DO NOT LIFT, CARRY OR HANG 40 PUMP BY THE ELECTRICAL �27\ CABLES. DAMAGE TO THE ELECTRICAL CABLES CAN CAUSE 60i SHOCK, BURNS OR DEATH. Hazardous voltage can shock, burn or cause death. Lift the pump with an adequately sized chain or cable at- tached to the lifting eye bolt. DO NOT damage electrical and sensor cables while raising and lowering unit. In many effluent and sewage basins or lift stations it is advisable to install the pump on a guide rail system or on a lift -out adapter to facilitate installation and removal for inspection and/or service. Most codes do not allow personnel to enter a wetwell without the correct protective equipment and training. Guide rails are designed to allow easy removal of the pump without the need for entry into the wetwell or need to disturb piping. The guide rail or lift -out adapter should locate the pump opposite the influent opening preventing stagnate areas where solids can settle. The basin or pit must be capable of supporting the weight of the pump and guide rail. The pit floor must be flat. NOTICE: FOLLOW THE INSTRUCTIONS THAT ARE PROVIDED WITH THE GUIDE RAIL ASSEMBLY. Discharge piping should be no smaller than the pump discharge diameter and kept as short as possible, avoiding unnecessary fittings to minimize friction losses. Install an adequately sized check valve to prevent fluid backflow. Backflow can allow the pump to "turbine" backwards and may cause premature seal and/or bearing wear. If the pump is turning backwards when it is called on to start the increased torque may cause damage to the pump motor and/or motor shaft and some single-phase pumps may actually run backwards. Install an adequately sized gate valve AFTER the check valve for pump, plumbing and check valve maintenance. Important — Before pump installation. If pumping waste water containing solids, drill a 3/16" (4.8mm) relief hole in the discharge pipe. It should be located within the wetwell, 2" (51mm) above the pump discharge but below the check valve. The relief hole allows any air to escape from the casing. Allowing liquid into the casing will insure that the pump can start when the liquid level rises. Unless a relief hole is provided, a bottom intake pump could "air lock" and will not pump water even though the impeller turns. All piping must be adequately supported, so as not to impart any piping strain or loads on the pump. The pit access cover must be of sufficient size to allow for inspection, maintenance and crane or hoist service. WI NG AND GROUNDING Important notice: Read Safety Instructions before proceeding with any wiring. AUse only stranded copper wire to pump/motor and ground. The ground wire must be at least as large as the power supply wires. Wires should be color coded for ease of maintenance and troubleshooting. AInstall wire and ground according to the National Electrical Code (NEC), or the Canadian Electrical Code, as well as all local, state and provincial codes. AInstall an all leg disconnect switch where required by code. ADisconnect and lockout electrical power before performing any service or installation. AThe electrical supply voltage and phase must match all equipment requirements. Incorrect voltage or phase can cause fire, motor and control damage, and voids the warranty. AAll splices must be waterproof. If using splice kits follow manufacturer's instructions. AWARNING Select the correct type and NEMA grade junction box for the application and loca- tion. The junction box must insure dry, safe wiring connections. A WARNING Seal all controls from gases present which may damage electrical components. AWARNING FAILURE TO PERMANENTLY Hazardous GROUND THE PUMP, MOTOR AND voltage CONTROLS BEFORE CONNECTING TO POWER CAN CAUSE SHOCK, BURNS OR DEATH. 9 ,,, i 1 FLOAT SWITCH TYPES There are two types of float switches available for use with 2 HP, single phase grinder pumps; single action con- trol switches and wide angle mechanical switches. Single action control switches can only be connected through a control panel. Connecting them directly to a pump will cause rapid cycling and may burn up the mo- tor, and/or the motor start switch and/or the float switch. If using single action switches with a control panel please see the Float Switch and Panel Section. Model A2G33 wide angle pump float switches can be hard wired directly to the pump. Wide angle switches can operate the pump via connection to a control panel. The tether length or distance from the switch body to the piv- ot point controls the On and Off points and the amount pumped in one cycle. The pivot point is where the float is attached to the discharge pipe. See Figures 1 and 2. SETTING THE FLOAT SWITCHES There are no absolute rules for where to set the float switches, it varies from job to job. Suggested Rules to Follow: All floats should be set below the Inlet pipe! Off Float: Best: set so the water level is always above the top of the pump (motor dome). Next Best: set so the wa- ter level is not more than 6" below the top of the pump. On Float: set so the volume of water between the On and Off floats allows two (2) HP and .larger pumps to run a minimum of 2 minutes. Basin literature states the gallons of storage per inch of basin height. Lag/Alarm Float(s): should be staggered above the Off and On floats. Try to use most of the available storage provided by the basin, save some space for reserve stor- age capacity. See Diagrams and Charts in Float Switch Chart Section. PANEL WIRING DIAGRAMS Our control panels are shipped with instructions and wir- ing diagrams. Use those instructions in conjunction with this IOM. Electrical installation should be performed only by qualified technicians. Any problem or questions pertaining to another brand control must be referred to that control supplier or manufacturer. Our technical people have no technical schematics or trouble shooting information for other companies' controls. ALARMS We recommend the installation of an alarm on all Waste- water pump installations. Many standard control panels come equipped with alarm circuits. If a control panel is not used, a stand alone high liquid level alarm is avail- able. The alarm alerts the owner of a high liquid level in the system so they can contact the appropriate service personnel to investigate the situation. SINGLE PHASE PUMPS AWARNING PLUG -CONNECTED UNITS MUST BE CONNECTED TO A PROPERLY GROUNDED, GROUNDING TYPE RECEPTACLE. ON NON -PLUG UNITS, DO NOT RE- MOVE CORD AND STRAIN RELIEF. Hazardous voltage DO NOT CONNECT CONDUIT TO can shock, burn or PUMP. i.cause death. Pumps with bare lead power cords can be hard -wired to a float switch, wired to a 10 contactor, a Simplex controller or a Duplex controller. Always verify that the float switch is rated for the maximum run amperage, maximum starting amperage, and the HP rating on the pump. Single-phase wastewater pumps contain on -wind- ing overloads, unless noted on the pump nameplate. See Figure 1. SINGLE PHASE CONTROL PANELS: Control panels are available as Simplex (controls 1 pump) or Duplex (controls 2 pumps). Our standard control panels are available with many standard features and can be built with our most popular options. We also custom build panels which offer many more design op- tions than the standard panels. Custom control panels are available in many different configurations. Custom panel quote requests may be forwarded to Customer Service through any authorized distributor. Our standard duplex panels feature a solid-state printed circuit board design with standard high level alarm cir- cuits. Other standard features are: an auxiliary dry alarm contact for signaling a remote alarm and float switch po- sition indicator lights. Most standard panels are in stock for immediate delivery. STANDARD PUMP INSTALLATION Connect the pump(s) to the guide rail pump adapters or to the discharge piping. Guide rail bases should be anchored to the wetwell floor. Complete all wiring per the control panel wiring dia- grams and NEC, Canadian, state, provincial and/or local codes. 7n� DO NOT PLACE HANDS IN PUMP SUCTION WHILE CHECKING MOTOR ROTATION. TO DO SO WILL CAUSE SEVERE PERSONAL INJURY. Lower the pump(s) into the wetwell. Hazardous Machinery Check to insure that the floats will operate freely and will not contact the piping. Connect the piping per local codes and the drawings in Typical Drawings Section. OPERATION Once the piping connections are made and checked you can run the pumps. Hard Wired Float Switch Operation — Turn circuit break- er or fused disconnect to On. Test the pump by filling the wetwell until the pump goes On. If the pumps run but fail to pump, they are probably air locked, drill the relief holes per the instructions in the Piping Section. Check the operating range to insure a minimum two min- ute run time and that the pump goes Off in the correct position. Control Panel Operation — Fill the wetwell with clear water. Use the pump H -O -A (Hand -Off -Automatic) switches in Hand to test the pumps. If they operate well in Hand proceed to test Automatic operation. If the pumps run but fail to pump, they are probably air locked, drill the relief holes per the instructions in the Piping Section. Place Control Panel switch(es) in Automatic position and thoroughly test the operation of the ON, OFF, and Alarm floats by filling the wetwell with clear water. Important: Failure to provide a Neutral from the power supply to a 10, 230 volt Control Panel will not allow the panel control circuit to operate. The Neutral is necessary to complete the 115 volt control circuit. Check voltage and amperage and record the data on the front of this manual for future reference. Compare the amperage readings to the pump nameplate maximum amperage. If higher than nameplate amperage investigate cause. Operating the pump off the curve, i.e. with too little head or with high or low voltage will increase am- perage. The motor will operate properly with voltage not more than 10% above or below pump nameplate ratings. Performance within this range will not necessarily be the same as the published performance at the exact rated nameplate frequency and voltage. Correct the problem before proceeding. Reset the Alarm circuit, place pump switch(es) in the Automatic position and Control Switch in ON position. The system is now ready for automatic operation. Explain the operation of the pumps, controls and alarms to the end user. Leave the paperwork with the owner or at the control panel if in a dry, secure location. . MIN e � 7 f. 4 � Irma 11 The purpose of this chart is to show the required switch quantities and the function of each switch in a typical wastewater system. The quantities required vary de- pending on the switch type, single-action or wide-angle. Switch quantities also vary by panel type: simplex with and without alarms, and duplex with alarms. Duplex Panels using single-action switches: Three Float Panel Wiring Inlet SW1 Bottom Pumps Off SW2 Middle 1st Pump On Alarm S\ SW3 Top 2nd Pump & Alarm On Pump On SW: Four Float Panel Wiring _0 SW1 Bottom Pumps Off SW2 2nd Pump Off SV 1st Pump On SW3 3rd 2nd Pump On SW4 Top Alarm On Duplex Panels using wide-angle switches: Three Float Panel Wirine SW1 Bottom SW2 Top Four Float Panel Wiring SW1 Bottom SW2 Middle SW3 Top 1st Pump On/Both Off 2nd Pump & Alarm On 1st Pump On/Both Off 2nd Pump On Alarm On Simplex Panel using single-action switches: Simplex Panel with Alarm SW1 Bottom Pump Off SW2 Middle Pump On SW3 Top Alarm On/Off Simplex Panel with No Alarm SW1 Bottom Pump Off SW2 Top Pump On Simplex Panel using wide-angle switches: Simplex Panel with Alarm SW1 Bottom Pump On/Off SW2 Top Alarm On/Off Simplex Panel with No Alarm SW1 Pump On/Off Inlet Alarm Lag Pump I SW3 Lead Pump SW2 Pump SW Simplex T Duplex rge rge ENGINEERING DATA Engineering data for specific models may be found in your catalog and on our website (address is on the cover). Control panel wiring diagrams are shipped with the control panels. Please use the control panel drawings in conjunction with this instruction manual to complete the wiring. PUMP OPERATION Minimum Submergence Maximum Fluid Temperature Continuous Continuous 104° F 40° C Duty Fully Submerged Operation Intermittent Intermittent 140° F 60° C Duty 6" Below Top of Motor Operation A2G33 - Hard Wired Determining Pumping Range Figure 1 Wide -Angle Float Switch Piggyback Pump plug switch plug Yrr I Pumpin range i Figure 2 Pumping Range (inches) Figure 3 Single -Action Float Switch "Typical" Installation 8"(20.3 =)TURN ON LEVEL Figure 4 WEIGHT —7 6"(15.3 an) (15.3—) INSULATION SISTANCE READINGS Normal Ohm and Megohm Values between all leads and ground MotorCondition of Ohm Value Megohm A new motor (without drop cable). 20,000,000 (or more) 20 (or more) A used motor which can be reinstalled in well. 10,000,000 (or more) 10 (or more) New motor. 2,000,000 (or more) 2 (or more) Motor in good condition. 500,000 - 2,000,000 .5-2 Insulation damage, locate and repair. Less than 500,000 Less than .5 Insulation resistance varies very little with rating. Motors of all HP, voltage and phase ratings have similar values of insulation resistance. Insulation resistance values above are based on readings taken with a megohmmeter with a 500V DC output. Readings may vary using a lower voltage ohmmeter, consult factory if readings are in question. INFLUENT SERVICE POLE CONTROL PANEL ("l _/_ ALARM LIGHT z- HINGEDACCESS DOOR tkfflw:Lfl-� MERCURYSWITCH HIGH LEVELALARM (OPTIONAL) MERCURYSWITCH GUIDE RAIL M R Y F SIMPLEX INFLUENT SERVICE POLE CONTROL VENT PANEL _ VALVE I C OPERATING (, J ROD INLET HUB —DISCHARGE MERCURY SWITCH HIGH LEVELALARM (OPTIONAL) CHECKVALVE LOWER PUMPGUIDE MERCURYSWITCH ALARM LIGHT r— HINGEDACCESS DOOR GUIDE RAIL b 1 DUPLEX VENT VALVE OPERATING ROD DISCHARGE CHECK VALVE LOWER PUMP GUIDE S _ £ Simplex Single Phase Wiring Diagram S10020 115/230 VAC (FOR 115 VAC, USE TERMINALS L1 AND N, JUMP L2 AND N). SINGLE PHASE, 60 Hz r-- si I 1 I I 1 PUMP _ I I 1 NOTE: WHEN USING SEPARATE 115 VAC CONTROL POWER SUPPLY, REMOVE GN i J1 JUMPER (J7) FROM TERMINALS (0) AND LL1). CONNECT 15 AMP MAX. 6 _ _ PROTECTED 115 VAC SUPPLY TO TERMINALS (LL1) AND (N) WITH / LL1 THE NEUTRAL OF THE SUPPLY TO (N). A 230 VOLT SYSTEM CONTROL REQUIRES A 4 WIRE ON-OFF POWER SUPPLY LINE L1, L2, d AND GND. WITHOUT A NEUTRAL THE CONTROL CIRCUIT WILL NOT WORK. RUN HAND S1 -AUX O OFF o- 4r_.,"o- I 3 /AUTO 1 OFF FLOAT ON FLOAT 1 1 I ALARM FLOAT J1---_ R1 C-l HIGH LEVEL ALARM DRY CONTACTS R2 FLASH 00 00 00 00 00 L1 L2 LL1 N 1 2 3 4 5 6 T1 T2 0 O FOR 115 VAC OPERTION, I I 1 USE TERMINALS L1 AND N, I I 1 JUMP TERMINALS L2 AND N. 1 I 1 1 1 I I I I 1 I 1 I I I 1 1 I I I 115/230 VAC©� I I SINGLE PHASE - - - - - - J 60 Hz t-------------1 1 1 1 1 I I I I 1 I 1 1 I I I I I I I I 1 I I 1 I I I I I I I I I 1 1 I 1 I I I I 1 I I I I I 1 I I I I I I I IR1 I I I 1 I 1 I 11° DRY CONTACTS I I I I I I I I 1 6 1 ALARM FLOAT O I 1 1 I 1 1 ON FLOAT[ PUMP 1 I OFF FLOAT Pi TROUBLESHOOTING AWARNING FAILURE TO DISCONNECT AND LOCKOUT ELECTRICAL Hazardous POWER BEFORE ATTEMPTING ANY SERVICE CAN CAUSE voltage SHOCK, BURNS OR DEATH. SYMPTOM PROBABLE CAUSE RECOMMENDED ACTION MOTOR NOT RUNNING Motor thermal protector tripped. Allow motor to cool. Insure minimum pump NOTE: If circuit breaker submergence. Clear debris from casing and impeller. "OPENS" repeatedly, Open circuit breaker or blown fuse. Determine cause, call a qualified electrician. DO NOT reset. Call qualified electrician. a) Manual operation b) Automatic operation NOTE: Check the pump in manual mode first to confirm operation. If pump operates, the automatic control or wiring is at fault. If pump does not operate, see above. Pump impeller binding or jammed. Power cable is damaged. Inadequate electrical connection in control panel. No neutral wire connected to control panel. Inadequate electrical connection in control panel. Defective liquid level switch. Insufficient liquid level to Liquid level cords tangled. Check motor amp draw. If two or more times higher than listed on pump nameplate, impeller is locked, motor bearings or shaft is damaged. Clear debris from cutter, casing and impeller, consult with dealer. Resistance between power leads and ground should read infinity. If any reading is incorrect, call a qualified electrician. Inspect control panel wiring. Call a qualified electrician. With switch disconnected, check continuity while activating liquid level switch. Replace switch, as required. Allow liquid level to rise 3" to 4" (76 mm - 101 mm) activate controls. above turn -on level. Untangle cords and insure free operation. PUMP WILL NOT Liquid level cords tangled. Untangle cords and insure free operation. TURN OFF Pump is air locked. Shut off pump for approximately one minute, then restart. Repeat until air lock clears. If air locking persists in a system with a check valve, a 3/,6" (4.8 mm) hole may be drilled in the discharge pipe approximately 2" (51 mm) above the discharge connection. Influent flow is matching pump's Larger pump may be required. discharge capacity. LITTLE OR NO LIQUID Check valve installed backwards, Check flow arrow on valve and check valve DELIVERED BY PUMP plugged or stuck closed. operation. Excessive system head. Pump inlet plugged. Improper voltage or wired incorrectly. Pump is air locked. Impeller is worn or damaged. Consult with dealer. Inspect and clear as required. Check pump rotation, voltage and wiring. Consult with qualified electrician. See recommended action, above. Inspect impeller, replace as required. Liquid level controls defective Inspect, readjust or replace as required. or improperly positioned. PUMP CYCLES Discharge check valve inoperative. Inspect, repair or replace as required. CONSTANTLY Sewage containment area too small. Consult with dealer. Liquid level controls defective or improperly positioned. Influent excessive for this size Inspect, readjust or replace as required. Consult with dealer. LIMITED CONSUMER WARRANTY For goods sold for personal, family or household purposes, Seller warrants the goods purchased hereunder (with the exception of membranes, seals, gaskets, elastomer materials, coatings and other "wear parts" or consumables all of which are not warranted except as otherwise provided in the quotation or sales form) will be free from defects in material and workmanship for a period of one (1) year from the date of installation or eighteen (18) months from the product date code, whichever shall occur first, unless a longer period is provided by law or is specified in the product documentation (the "Warranty"). Except as otherwise required by law, Seller shall, at its option and at no cost to Buyer, either repair or replace any product which fails to conform with the Warranty provided Buyer gives written notice to Seller of any defects in material or workmanship within ten (10) days of the date when any defects or non-conformance are first manifest. Under either repair or replacement option, Seller shall not be obligated to remove or pay for the removal of the defective product or install or pay for the installation of the replaced or repaired product and Buyer shall be responsible for all other costs, including, but not limited to, service costs, shipping fees and expenses. Seller shall have sole discretion as to the method or means of repair or replacement. Buyer's failure to comply with Seller's repair or replacement directions shall terminate Seller's obligations under this Warranty and render this Warranty void. Any parts repaired or replaced under the Warranty are warranted only for the balance of the warranty period on the parts that were repaired or replaced. The Warranty is conditioned on Buyer giving written notice to Seller of any defects in material or workmanship of warranted goods within ten (10) days of the date when any defects are first manifest. Seller shall have no warranty obligations to Buyer with respect to any product or parts of a product that have been: (a) repaired by third parties other than Seller or without Seller's written approval; (b) subject to misuse, misapplication, neglect, alteration, accident, or physical damage; (c) used in a manner contrary to Seller's instructions for installation, operation and maintenance; (d) damaged from ordinary wear and tear, corrosion, or chemical attack; (e) damaged due to abnormal conditions, vibration, failure to properly prime, or operation without flow; (f) damaged due to a defective power supply or improper electrical protection; or (g) damaged resulting from the use of accessory equipment not sold or approved by Seller. In any case of products not manufactured by Seller, there is no warranty from Seller; however, Seller will extend to Buyer any warranty received from Seller's supplier of such products. Goulds Water Technology Policy Concerning Online Sales to Consumers. Homeowners using the Internet to locate information regarding residential water systems, residential wastewater systems, controls and tanks may discover several sites offering a direct -to -consumer purchasing opportunity. Residential water and wastewater systems are mission critical applications and are designed to be installed by qualified professionals. Goulds Water Technology has an extensive nationwide network of distributors and dealers, including authorized resellers. For a complete view of Goulds Water Technology recognized distributors, dealers and authorized resellers, please refer to our locator at: http://goulds.com/sales-service/ No warranty is offered on Goulds Water Technology equipment purchased over the Internet, including web -based options from unauthorized retailers. This policy is necessary to ensure that Goulds Water Technology equipment is installed properly, in compliance with applicable laws, rules and codes, in a manner that addresses safety concerns and the proper performance of Goulds Water Technology equipment. THE FOREGOING WARRANTY IS PROVIDED IN PLACE OF ALL OTHER EXPRESS WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE (1) YEAR FROM THE DATE OF INSTALLATION OR EIGHTEEN (18) MONTHS FROM THE PRODUCT DATE CODE, WHICHEVER SHALL OCCUR FIRST. EXCEPTAS OTHERWISE REQUIRED BY LAW, BUYER'S EXCLUSIVE REMEDYAND SELLER'S AGGREGATE LIABILITY FOR BREACH OF ANY OF THE FOREGOING WARRANTIES ARE LIMITED TO REPAIRING OR REPLACING THE PRODUCTAND SHALL IN ALL CASES BE LIMITED TO THE AMOUNT PAID BYTHE BUYER FOR THE DEFECTIVE PRODUCT. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY OTHER FORM OF DAMAGES, WHETHER DIRECT, INDIRECT, LIQUIDATED, INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY OR SPECIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LOSS OF PROFIT, LOSS OF ANTICIPATED SAVINGS OR REVENUE, LOSS OF INCOME, LOSS OF BUSINESS, LOSS OF PRODUCTION, LOSS OF OPPORTUNITY OR LOSS OF REPUTATION. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. To make a warranty claim, check first with the dealer from whom you purchased the product or visit www.xyleminc.com for the name and location of the nearest dealer providing warranty service. )cyte m Xylem Inc. Let's Solve Water 2881 East Bayard Street Ext., Suite A Seneca Falls, NY 13148 Phone: (866) 325-4210 Fax: (888) 322-5877 www.gouldswatertechnology.com Goulds is a registered trademark of Goulds Pumps, Inc. and is used under license. ® 2016 Xylem Inc. IM038 Revision Number 6 February 2016 MANUAL DE INSTRUCC16N IM038R06 B o m b a t rtt-U- Tad' o ra BUILT IN THE 'r M -0 -mo • ' USA ENGINEERED, ASSEMBLED & TESI selio unico INSTRUCCIONES DE INSTALACION, FUNCIONAMIENTO Y MANTENIMIENTO yl ` GOULDS A° ER TECHNOLOGY a xylem brand Indice i14,AIc1 PAGINA Instruccionesde seguridad......................................................................................................................................... Verificaciones preliminares a la instalaci6n................................................................................................................. Levantamientode la bomba....................................................................................................................................... Riel de guia o sistema de levantamiento opcional...................................................................................................... Tuberfas..................................................................................................................................................................... Alambrado y conexi6n a tierra.................................................................................................................................. Selecci6n y cableado de los interruptores y paneles de control de la bomba............................................................... Instalaci6n................................................................................................................................................................. Operaci6n................................................................................................................................................................. Tabla del panel a interruptores de flotador................................................................................................................. 14 14 14 14 15 15 15 16 17 18 Datosde ingenieria..................................................................................................................................................... 19 Lecturas de resistencia de la instalaci6n...................................................................................................................... 20 Instalaciones tipicas y diagramas de cableado de la bomba de diseno simple............................................................... 21 Identificaci6n y resoluci6n de problemas.................................................................................................................... 22 Garandalimitada........................................................................................................................................................ 23 Numero de modelo de la bomba: Numero de serie de la bomba: Numero de modelo del control: Agente: No. telef6nico del agente: Fecha de compra: , Instalaci6n: Lecturas actuales en el momento de la puesta en marcha: 10 Amperios: Voltios: — INSTRUCCIONES DE SEGURIDAD PARA EVITAR LESIONES PERSONALES GRAVES O AUN FATALES Y SERIOS DANOS MATERIALES, LEA Y SIGA TODAS LAS INSTRUCCIONES DE SE- GURIDAD EN EL MANUAL YEN LA BOMBA. ESTE MANUAL HA SIDO CREADO COMO UNA GWA PARA LA INSTALAC16N Y OPERAC16N DE ESTA UNIDAD Y SE DEBE CONSERVAR JUNTO A LA BOMBA. Este es un SIMBOLO DE ALERTA DE SEGURIDAD. Cuando vea este sfmbolo en la bomba o en el manual, busque una de las siguientes palabras de sefial y este alerta a la probabilidad de lesiones personales o dafios materiales. Advierte los peligros que CAUSARAN graves lesiones personales, la muerte o dafios materiales mayores. AnnvEumaA Advierte los peligros que PUEDEN causar graves lesiones personales, la muerte o dafios materiales mayores. Advierte los peligros que PUEDEN causar lesiones personales o danos materiales. AVISO: INDICA INSTRUCCIONES ESPECIALES QUE SON MUY IMPORTANTES Y QUE SE DEBEN SEGUIR. EXAMINE BIEN TODAS LAS INSTRUCCIONES Y ADVERTENCIAS ANTES DE REALIZAR CU- ALQUIER TRABAJO EN ESTA BOMBA. MANTENGA TODAS LAS CALCOMANIAS DE SEGURIDAD. AADVEi►MW Todo el trabajo el6ctrico debe ser realizado por un t6cnico calificado. Siempre siga el C6digo E16ctrico de EE.UU. (NEC) o el C6digo El6ctrico Canadiense, ademis de todos los c6digos locales, estat- ales y provinciales. Las preguntas acerca del c6digo deben ser dirigidas al inspector el6ctrico local. Si se hace caso omiso a los c6digos el6ctricos y normas de seguridad de OSHA, se pueden producir lesiones personales o dafios al equipo. Si se hace caso omiso a las instrucciones de in- stalaci6n del fabricante, se puede producir electrochoque, peligro de incendio, lesiones personales o aun la muerte, dafios al equipo, rendimiento insatisfactorio y podrfa anularse la garantfa del fabricante. AADWRTENW Las unidades estindar no estin disefiadas para usarse en albercas, masas abiertas de agua, lfquidos peligrosos o donde existan gases inflam- ables. Estos fluidos y gases podrfan estar presentes en areas de contenci6n. El tanque o pozo debe ser ventilado de acuerdo con los c6digos locales. En lugares con lfquidos inflamables o donde pudiese haber gases inflamables s6lo deben usarse bombas especf- fica-mente clasificadas para ireas de Clase 1, Divisi6n 1. Consulte los boletines de catdlogos de bombas especificas o la placa de identi ficaci6n de la bomba con respecto a las listas de agencias. AAMRiMw Desconecte y bloquee la corriente el6ctrica antes de instalar o dar servicio a cualquier equipo el6ctrico. Muchas bombas estin equipadas con protecci6n automitica contra la sobrecarga t6rmica, la cual podrfa permitir que una bomba demasiado caliente rearranque inesperadamente. Abra todas las cajas a inspeccione el equipo para determi- nar si se ocasionaron dafios durante el envfo. Notifique cualquier dafio a su proveedor o a la compafifa de trans- porte de inmediato. Importante: Siempre verifique que las clasificaciones de corriente, tensi6n, fase y potencia en la placa de identi- ficaci6n de la bomba correspondan con las del panel de control y fuente de alimentaci6n. Muchas de nuestras bombas para alcantarillado estin Ilenas con aceite. Si hay alguna sepal de fuga de aceite o si la unidad estuvo almacenada durante largo tiempo, verifique el nivel de aceite en la cupula del motor y la caja del sello, en caso de haberla. Verifique el nivel de aceite de la cubierta del motor a trav6s del tap6n de la tuberfa en el extremo superior de la unidad. El aceite en la cimara del motor debe cubrir apenas el motor. iNo Ilene en exceso, deje espacio para expansi6n! Si el nivel esti bajo, agregue aceite para turbinas ASTM 150. Reinstale el tap6n. Puede obtenerse aceite en latas de 5 galones de nuestros distribuidores. Tambi6n puede obtener aceite a nivel local en talleres de reparaci6n de motores. Las marcas tfpicas de aceite son: Shell Turbo 32, Sunoco Sunvis 932, Texaco Regal R&O 32, Exxon Nuto 32 y Mobil DTE Light. Inspeccione la tuerca de alivio de tensi6n en los conjun- tos de protecci6n contra drones de los cables de aliment- aci6n. Torsi6n de los cables de alimentaci6n: 75 pulg.-lbs. para cables #16 y 80 pulg.-lbs. para todos los otros tipos de cable. La garantfa no cubre dafios causados por conectar bom- bas y controles a la fuente de energfa incorrecta (fuente . de tensi6n/fase). Anote los numeros de modelos y numeros de serie de las bombas y del panel de control en la secci6n delantera de este manual de instrucciones para referencia futura. Entregue el manual al propietario o adjuntelo al panel de control una vez finalizada la instalaci6n. �: 11 d • is ; AArvearENcu► NO LEVANTE NI TRANSPORTE 0 NI CUELGUE LA BOMBA DE LOS CABLES ELECTRICOS. EL DANO A LOS CABLES ELE,CTRICOS PUEDE PRODUCIR ELECTROCHOQUE, 01 QUEMADURAS O AUN LA MUERTE. Un vokaje peogroso puede producir golpesel§ dm, quemadwas o M mueft. Levante la bomba con una cadena o cable de tamafio adecuado conectado al perno de ojo de levantamiento. NO dare los cables el6ctricos o de los sensores al subir y bajar la unidad. RIEL DE GdA 0 SISTEMA DE LEVANTAMMNTO OPCIONAL En muchos estanques de efluente y aguas negras o estaciones de levantamiento se recomienda instalar la bomba en un sistema de riel de gufa o sobre un adapta- dor de levantamiento para facilitar la instalaci6n y retiro para inspeccion y/o servicio. La mayorfa de los codigos no permite que el personal entre al pozo sin el equipo de protecci6n y la capacitation correctos. Los rieles de gufa estan disefiados para facilitar el retiro de la bomba sin necesidad de entrar al pozo o perturbar la tuberfa. El riel de gufa o el adaptador de levantamiento debe situar la bomba opuesta a la abertura para el lfquido de entrada, evitando las areas estancadas donde pudiesen asentarse solidos. El estanque o fosa debe ser capaz de soportar el peso de la bomba y del riel de gufa. El piso de la fosa debe ser plano. AVISO: SIGA LAS INSTRUCCIONES INCLUIDAS CON EL CONJUNTO DEL RIEL DE GUTA. La tuberfa de descarga no debe ser mas pequefia que el diametro de descarga de la bomba y debe mantenerse to mas corta posible, evitando los accesorios innecesarios para reducir al mfnimo las perdidas por friction. Install an adequately sized check valve to prevent fluid backflow. El contraflujo puede hater que la bomba "gire" en direction inversa, produciendo un desgaste prematuro del sello y/o del cojinete. Si la bomba gira en sentido inverso al arrancar, el aumento de torsion puede dafiar el motor y/o el eje del motor de la bomba y algunas bombas monofasicas hasta podrfan funcionar en sentido inverso. Instale una vilvula de compuerta de tamafio adecuado DESPUES de la valvula de retencion para facilitar el mantenimiento de la bomba, las tuberfas y la valvula de retencion. .. Importante — antes de instalar la bomba. Si se va a bombear agua residual con solidos, perfore un orificio de alivio de 3/16 pulg. (4.8 mm) en la tuberfa de descarga. Debe situarse dentro del pozo, a 2 pulg. (51 mm) sobre la descarga de la bomba, pero debajo de la vdlvula de retencion. El orificio de alivio permite el escape de aire de la carcasa. Al permitir que entre lfquido a la carcasa se asegura que la bomba pueda arrancar cuando el nivel de lfquido aumente. A menos que se proporcione un orificio de alivio, una bomba de toma inferior podrfa "obstruirse con aire" y no bombear agua, a pesar de que el impulsor gire. Todas las tuberfas deben estar apoyadas correctamente, de modo que no se apliquen esfuerzos o cargas de las tuberfas a la bomba. La cubierta de acceso a la fosa debe ser de tamafio su- ficiente para permitir realizar el servicio de inspeccion, mantenimiento y levantamiento con grua o montacargas. Aviso importante: Lea las instrucciones de seguridad antes de proseguir con el cableado. Use unicamente alambre trenzado de cobre para la bomba/motor y la conexion a tierra. El alambre de conexion a tierra debe ser al menos del mismo tamafio que los alambres de la fuente de aliment- acion. Los alambres deben codificarse con colores para facilitar el mantenimiento y la identification y resolution de problemas. AInstale los cables y la conexion a tierra de acuerdo con el Codigo Electrico de EE.UU. (NEC) o el C6- digo Electrico Canadiense, ademas de los codigos locales, estatales.y provinciales. AInstale un desconectador de todos los circuitos donde el c6digo to requiera. ADesconecte y bloquee la corriente electrica antes de instalar o dar servicio. ALa tension y fase de la fuente de alimentation debe corresponder con todos los requerimientos del equipo. La tension o fase incorrecta puede pro- ducir incendio, dafio al motor o a los controles y anula la garantfa. ATodos los empalmes debe ser impermeables. Si utiliza juegos de empalme, siga las instrucciones del fabricante. AAwERmc:L4 Seleccione una Caja de conexiones NEMA del tipo correcto para la aplicaci6n y ubicaci6n. La caja de conexiones debe ga- rantizar conexiones de cableado seguras y setas. A,auvmrF.Naa Selle todos los controles de los gases presentes que pudiesen dafiar los compo- nentes electricos. AIwvWMNCIA LA FALLA DE CONECTAR A TIERRA PERMANENTEMENTE LA BOMBA, Tension EL MOTOR Y LOS CONTROLES, peligrosa ANTES DE CONECTAR LA CORRIENTE ELECTRICA PUEDE CAUSAR ELECTROCHOQUE, QUEMADURAS O LA MUERTE. IS =11 i �- E k, �; TIPOS DE INTERRUPTORES DE FLOTADOR Hay dos tipos de interruptores de flotador disponibles para usarse con las bombas trituradoras monofasicas de 2 caballos de fuerza: interruptores de control de action simple a interruptores mecanicos de Angulo amplio. Los interruptores de control de accion simple, solo pueden conectarse a traves de un panel de control. Si se conectan directamente a una bomba, se producira un ciclado ripido y se podrfa quemar el motor y/o el interruptor de arranque del motor y/o el interruptor de flotador. Si se utilizan interruptores de accion simple con un panel de control, consulte la Seccion del Panel e Interruptor de flotador. Los interruptores de bomba de flotador de Angulo amplio Modelo A2G33 se pueden conectar directamente a la bomba. Interruptores de Angulo amplio pueden operar la bomba mediante una conexion al panel de control. La longitud de la atadura o la distancia desde el cuerpo del interruptor al punto de pivote controla los puntos de En- cendido y Apagado y la cantidad bombeada en un ciclo. El punto de pivote es donde el flotador esti conectado a la tuberfa descarga. Ver las Figuras 1 y 2. INSTALACION DE LOS INTERRUPTORES DE FLOTADOR No hay reglas absolutas acerca de d6nde instalar los interruptores de flotador, varfa de trabajo a trabajo. Reglas sugeridas a seguir: Mdos los flotadores deben instalarse debajo de la tuberfa de entrada! Flotador de apagado: Primera preferencia: instilelo de manera que el nivel del agua quede siempre sobre el extremo superior de la bomba (cupula del motor). Segunda preferencia: instilelo de manera que el nivel del agua quede a no mis de 6 pulg. por debajo del extremo superior de la bomba. Flotador de encendido: instilelo de manera que el volumen de agua entre los flotadores de encendido y apagado que las bombas de dos (2) caballos de fuerza y mayores funcionen al menos 2 minutos. La literatura sobre estanques establece los galones de almacenaje por pulgada de altura del estanque. Flotador(es) de retardo/alarma: deben escalonarse sobre los flotadores de apagado y encendido. Trate de utilizar la mayorfa del almacenaje disponible ofrecido por el estanque, ahorre espacio para la capacidad de almacenaje de reserva. Consulte los diagramas y tablas en la Secci6n de Tablas de Interruptores de Flotador. DIAGRAMAS DE CABLEADO DEL PANEL Nuestros paneles de control se envfan con instrucciones y diagramas de cableado. Utilice dichas instrucciones en conjunto con este manual de instrucciones (IOM). La instalaci6n el6ctrica debe ser realizada por t6cnicos calificados unicamente. Cualquier problema o preguntas con respecto al control de otras marcas debe dirigirse a ese proveedor o al fabricante del control. Nuestro per- sonal t6cnico no tiene diagramas esquemiticos t6cnicos o informaci6n de identificaci6n y resoluci6n de problemas de los controles de otras compafifas. ALARMAS Recomendamos la instalaci6n de una alarma en todas las bombas para aguas residuales. Muchos paneles de control estindar vienen equipados con circuitos de alarma. Si no se usa un panel de control, se ofrece una alarma por alto nivel de lfquido independiente. La alarma alerta al propietario acerca de una situaci6n de alto nivel de lfquido en el sistema, de manera que pueda comunicarse con el personal de servicio apropiado para que investigue la situaci6n. BOMBAS MONOFASICAS AADvFRTmaA LAS UNIDADES CON ENCHUFE DEBEN CONECTARSE A UN TOMACORRIENTES TIPO TIERRA CONECTADO CORRECTAMENTE A TIERRA. 400f EN EL CASO DE UNIDADES SIN ENCHUFE, NO QUITE EL CABLE a�u&op �� NI EL PROTECTOR CONTRA quemadumolamuerte. TIRONES. NO CONECTE EL TUBO- CONDUCTO A LA BOMBA. Las bombas con cables de alimentaci6n con conductores desnudos pueden conectarse directamente a un inter- ruptor de flotador, cablearse a un contactador de 1 fase, a un controlador simple o doble. Siempre verifique que el interruptor de flotador est6 clasificado para el ampe- raje de funcionamiento miximo, amperaje de arranque miximo y la capacidad nominal de potencia de la bomba. Las bombas monofisicas para aguas residuales contienen sobrecargas de devanado de encendido, a menos que se especifique to contrario en la placa de identificaci6n de la bomba. Ver la Figura 1. PANELES DE CONTROL MONOFASICOS: Los paneles de control pueden ser simples (controlan 1 bomba) o dobles (controlan 2 bombas). Nuestros paneles de control se ofrecen con muchas caracterfsticas estindar y pueden construirse con nuestras opciones mis popu- lares. Tambi6n construimos paneles de acuerdo con las especificaciones del cliente, los cuales ofrecen muchas mis opciones que los paneles. Los paneles de control construidos de acuerdo con las especificaciones del cli- ente se ofrecen en muchas configuraciones diferentes. Las solicitudes de cotizaciones para paneles a la medida pu- eden enviarse a Servicio a los Clientes mediante nuestro distribuidor autorizado. Nuestros paneles dobles presentan un disefio de tablero de circuito impreso de estado s6lido con circuitos de alar- mas de alto nivel estindar. Otras caracterfsticas estindar son: un contacto de alarma Seco auxiliar para sefializar una alarma remota y luces indicadoras de posici6n del interruptor de flotador. La mayorfa de los paneles se mantienen en inventario para entrega inmediata. INSTALACION DE BOMBA ESTANDAR Conecte la(s) bomba(s) a los adaptadores de riel de gufa o a la tuberfa de descarga. Las bases del riel de gufa deben anclarse al piso del pozo. Todas las conexiones deben realizarse de acuerdo con los diagramas de cableado del panel de control, el c6digo el6ctrico de EE.UU., el c6digo canadiense y los c6digos estatales, provinciales y/o locales. • . NO COLOQUE LAS MANOS EN LA SUCCION DE LA BOMBA MIEN- TRAS VERIFICA LA ROTACI6N DEL MOTOR. EL HACERLO PRODUCIRA GRAVES LESIONES PERSONALES. Baje la(s) bomba(s) al pozo. Inspec- cione para verificar que los flotadores Maqulnaria peligroea. funcionen libremente y que no hagan contacto con la tuberfa. Conecte las tuberfas de acuerdo con los c6digos locales y los dibujos en la Secci6n de Dibujos Tfpicos. Una vez que se hayan hecho y verificado las conexiones de las tuberfas, se pueden poner en funcionamiento las bombas. Flotador de conexi6n directs — Gire el cortacircuitos o el desconectador con fusible a la posici6n de Encendido. Pruebe la bomba llenando el pozo hasta que la bomba se active. Si las bombas funcionan pero no bombean, probablemente est6n obstruidas con aire; perfore los orificios de alivio de acuerdo con las instrucciones en la Secci6n de Tuberfas. Verifique el intervalo de operaci6n para asegurar dos tiempo de funcionamiento mfnimo de un minuto y que la bomba se apague en la posici6n correcta. Operaci6n del panel de control.— Llene el pozo con agua limpia. Utilice los interruptores H-O-A (manual — apagado — au- tomitico) de la bomba en la posici6n manual para probar las bombas. Si funcionan bien en la posici6n manual, pruebe la posici6n automatica. Si las bombas funcionan pero no bombean, probablemente esten obstruidas con aire; perfore los orificios de alivio de acuerdo con las instrucciones en la Secci6n de Tuberias. Coloque el (los) interruptor(es) del panel de control en la posici6n automatica y pruebe minuciosamente el funcio- namiento de los flotadores de ENCENDIDO, APAGADO y alarma Ilenando el pozo con agua limpia. Importante: Si no se proporciona un neutro desde la Fuente de alimentaci6n a un panel de control monofasico de 230 voltios, el circuito de control del panel no operara. Es necesario el neutro para completar el circuito de control de 115 voltios. Verifique la tensi6n y la corriente y anote los datos en la secci6n delantera de este manual para referencia futura. Compare las lecturas de amperaje con el amperaje maxi- mo indicado en la placa de identificaci6n de la bomba. Si es mas alto que el amperaje de la placa de identificaci6n, investigue la causa. Si la bomba se hace funcionar fuera de la curva; es decir, con demasiado poca carga o con tensi6n alta o baja, aumentari el amperaje. El motor funcionara correctamente con tensi6n no mis de un 10% por encima o por debajo de las clasificaciones en la placa de identificaci6n de la bomba. El rendimiento dentro de este rango no sera necesariamente igual al rendimiento publicado a la frecuencia y tensi6n exactas indicadas en la placa de identificaci6n. Corrija el problema antes de continuar. Reposicione el circuito de alarma, coloque el (los) interruptor(es) de la bomba en posici6n automatica y el interruptor de control en la posici6n de encendido. Ahora la unidad esta lista para la operaci6n automatica. Explique la operaci6n de las bombas, controles y alarmas al usuario final. Entregue la documentaci6n al propietario o dejela en un lugar seco y seguro en el panel de control. El prop6sito de esta tabla es mostrar las cantidades de interruptores requeridas y la funci6n de cada interruptor en un sistema de aguas residuales tipicas. Las cantidades requeridas varian dependiendo del tipo de interruptor: de acci6n simple o de Angulo amplio. Las cantidades de interruptores varian tambien de acuerdo con el tipo de panel: simple con y sin alarmas y doble con alarmas. Paneles dobles utilizando interruptores de acci6n simple: Cableado del panel de tres flotadores SW1 Fondo Bombas apagadas SW2 Medio Primera bomba encendida SW3 Extremo superior Segunda bomba y alarma encendidas Cableado del panel de cuatro flotadores 2 SW1 Fondo Bombas apagadas SW2 Segundo Primera bomba encendida SW3 Tercero Segunda bomba encendida SW4 Extremo superior Alarma encendida Paneles dobles utilizando interruptores de Angulo amplio: Cableado del panel de tres flotadores SW1 Fondo Primera bomba encendida/ ambas apagadas SW2 Extremo superior Segunda bomba y alarma encendidas Entrada Alarma SN Bomba encendid SW2 Bomba apaga SW1 ga Cableado del nanel'de cuatro flotadores SW1 Fondo Primera bomba encendida/ ambas apagadas SW2 Medio Segunda bomba encendida SW3 Extremo superior Alarma encendida Paneles simples utilizando interruptores de acci6n simple: Panel simple con alarma OO SW1 Fondo SW2 Medio SW3 Extremo superior Panel simple sin alarma SW1 Fondo SW2 Extremo superior Bomba apagada Bomba encendida Alarma encendida/apagada Bomba apagada Bomba encendida Paneles simples utilizando interruptores de Angulo amplio: Panel simple con alarma SW1 Fondo SW2 Extremo superior Panel simple sin alarma SW1 Ala Bomba sea encendida Bomba p encendic Bomba sW1 Bomba encendida/apagada Alarma encendida/apagada Bomba encendida/apagada Simple O Doble 2 ga DATOS DE INGENMRIA Los datos de ingenieria para modelos especificos pueden encontrarse en su catalogo y en nuestro sitio Web (direccion en la cubierta). Los diagramas de cableado del panel de control se envfan con los paneles de control. Utilice los dibujos del panel de control junto con este manual de instrucciones para completar el cableado. OPERACION DE LA BOMBA Sumersion minima Temperatura maxima del fluido Servicio continuo Sumergida totalmente Operacion continua 104° F - 40° C 6 pulp. por debajo del Operacion Senricio intermitente extremo superior del motor intermitente 140° F 60° C A2G33- Cableado directo Determinacion del rango de bombeo raja de Instalaci6n de coneziones fuente cableado direct de para aplicadones alimen- de120Vo 3m taci6n 230V. Negro tBlanco Co'nedordel cable :Z: bomba Figure 1 Interruptor de flotador de angulo amplio Enchufe de los Taplin de la bomba interruptores — `% flen t5ndem Rango de bombeo Figure 2 Rango de bombeo (pulgadas) Figure 3 Interruptor de flotador de accion simple Instalacion "tipica" Figure 4 0 cm) Valores normales en ohmios y mepohmios entre todos los conductores y tierra La resistencia del aislamiento varia muy poco con la clasificacion. Los motores de todas las clasificaciones de potencia, tension y fase tienen valores similares de resistencia de aislamiento. Los valores de resistencia de aislamiento anteriores estan basados en lecturas obtenidas con un megaohmio- metro con salida de 500 V CC. Las lecturas pueden variar utilizando un ohmiometro de tension mas baja; con- sulte con la fabrica si tiene dudas acerca de las lecturas. CONEXIONES E PMAIAC16N TIPICA LIQUIDO ENTRANTE POSTE DE SERVICIO - PANEL DE CONTROL CUBO DE -' ENTRADA INTERRUPTOR DE — MERCURI01 ALARMA POR NIVEL(OPCIONAL) INTERRUPTOR DE - MERCURIO LUZ DE ALARMA PUERTA DE ACCESO ABISAGRADA RIELDE ORIFICIO DE VENTILACION VARILLA DE MANDO DE LA VALVULA - DESCARGA L(QUIDO ENTRANTE POSTE DE SERVICIO PANEL DE CONTROL CUBO DEENTRADA INTERRUPTOR DE _ MERCURIO 1 ALARMA POR NIVEL(OPCIONAL) INTERRUPTOR DE .eroriioin VALVULA DE RETENCION GU(A INFERIOR DE LABOMBA DE ALARMA - PUERTA DE ACCESO ABISAGRADA \ ORIFICIO DE (� 11 VENTILACIbN RIELDE \ '"xVARILLADE GU(A MANDO DE LA VALVULA DESCARGA isr / VALVULA DE RETENCION x ' GU(A ° INFERIOR DE LA BOMBA DOBLE O � r �r � o DE ALARMA - PUERTA DE ACCESO ABISAGRADA \ ORIFICIO DE (� 11 VENTILACIbN RIELDE \ '"xVARILLADE GU(A MANDO DE LA VALVULA DESCARGA isr / VALVULA DE RETENCION x ' GU(A ° INFERIOR DE LA BOMBA DOBLE Diagrama de cableado de unidad simple monobsica S10020 115/230 VCA (PARA 115 VCA, UTILICE LOS TERMINALES L1 Y N, CONECTE EN PUENTE L2 Y N). MONOFASICA, 60 Hz I I I I 1 1 I I 51 -AUX APAGADO 51 I L1 I I I I I I I - ' BOMBA ITE -MA I J1 NOTA: CUANDO USE UNA FUENTE DE ALIMENTAC16N DE CONTROL DE FLOTADOR DE DE 115 VCA SEPARADA, RETIRE EL PUENTE (J1) DE LOS ENCENDIDO TERMINALES (L1) Y (LL1). CONECTE LA FUENTE DE ALIMENTA06N / LL1 DE 115 VCA PROTEGIDA DE 15 AMP. mAx. A LOS TERMINALES (1-1-1) Y (N) CON EL NEUTRO DE LA FUENTE A (N). UN SISTEMA DE 230 VOLTIOS CONTROL REnUIERE UNA FUENTE DE ON-OFF ALIMENTAC16N TETRAFILAR CON LINEA L1, L2, N Y TIERRA SIN NEUTRO, EL CIRCUITO DE CONTROL NO FUNCIONAR . J1 FUNCIONAMIENTO 1 I i I --��{4 FLOTADOR DE ALARMA R1 c "I CONTACTOSSECOS DE ALARMA DE ALTO NIVEL DESTELLO DESTELLADOR ALTO R2 0 0 0 0 0 .0 0 0 0 0 0 0 L1 L2 LL1 N 1 2 3 4 5 6 T1 T2 0 0 0 0 0 0 0 0 0 0 0 0 9PARA 115 VCA, UTILICE I I I LOS TERMINALES L1 Y N, 1 1 I CONECTE EN PUENTE L2 Y N I 1 1 I I I I I I I 1 I I I I I I 115/230 VCAB\- - I I MONOFSICA \ - - - -- - -_ - - I 60 Hz t- - - - - -_ 1 1 1 1 I I 1 I MANUAL I I I I 1 1 I I 51 -AUX APAGADO I I I I I 1 I I 1 1 I I 1 1 I 1 I 1 I 1 1 1 I R1 I o lr o- � O- 3 � AUiOMb.TICO 1 FLOTADOR DE FLOTADOR DE APAGADO ENCENDIDO 1 I i I --��{4 FLOTADOR DE ALARMA R1 c "I CONTACTOSSECOS DE ALARMA DE ALTO NIVEL DESTELLO DESTELLADOR ALTO R2 0 0 0 0 0 .0 0 0 0 0 0 0 L1 L2 LL1 N 1 2 3 4 5 6 T1 T2 0 0 0 0 0 0 0 0 0 0 0 0 9PARA 115 VCA, UTILICE I I I LOS TERMINALES L1 Y N, 1 1 I CONECTE EN PUENTE L2 Y N I 1 1 I I I I I I I 1 I I I I I I 115/230 VCAB\- - I I MONOFSICA \ - - - -- - -_ - - I 60 Hz t- - - - - -_ 1 1 1 1 I I 1 I I I I I I I 1 1 I I I 1 I I I I I 1 I I 1 1 I I 1 1 I 1 I 1 I 1 1 1 I R1 I I 1 I I I I I 1 I I 1 CONTACTOS I I 1 I I I 1 1 SEGOS 1 J 1 1 I I 1 1 Qv 1 I I 6 1 FLOTADOR I 1 1 I DE ALARMA o 1 I I I 1 FLOTADOR I 1 SOMBA 1 C DE 1 I ENCENDIDOI 1 FLOTADOR I 1 DEAPAGADO I 11 1 AADVEWMNcu► LA FALLA DE DESCONECTAR Y BLOQUEAR LA CORRIENTE ELECTRICA ANTES DE Tensi6n INTENTAR CUALQUIER SERVICIO, PUEDE CAUSAR ELECTROCHOQUE, QUEMADURAS O peligrosa LA MUERTE. SINTOMA CAUSA PROBABLE ACC16N RECOMENDADA EL MOTOR NO Se dispar6 el protector Deje que se enfrfe el motor. Asegure la sumersi6n ESTA FUNCIONANDO termico del motor minima de la bomba. Limpie los residuos de la NOTA: Si el cortacircuitos se carcasa y el impulsor. "ABRE" repetidamente, NO Cortacircuitos abierto o fusible quemado. Determine la causa, llame a un electricista calificado. to reposition. Dame a un electricista calificado. Impulsor de la bomba rozando o atascado. Determine el consumo de corriente del motor. Si es dos veces mas alto que el indicado en la plata de a) Operaci6n manual El cable de ahmentaci6n esti dafiado. identificaci6n de la bomba, el impulsor esti trabado, los Conexiones electricas inadecuadas cojinetes del motor o el eje esti dafiado. Limpie los en el panel de control. residuos de cutter, la carcasa y el impulsor, consulte con el agente. b) Operaci6n automatica NOTA: Inspection la bomba en modo manual primero para confirmar el funcionamiento. Si la bomba funciona, el control automitico o el cableado esti defectuoso Si la bomba No hay alambre neutro conectado al panel de control. Conexiones el6ctricas inadecuadas en el panel de control. Interruptor de nivel de liquido defectuoso para activar los controles. Nivel de liquido insuficiente para activar los controles. La resistencia entre los conductores de alimentaci6n y tierra debe indican infinito. Si alguna lectura es incorrecta, llame a un electricista calificado. Inspeccione las conexiones del panel de control. Llame a un electricista calificado. Con el interruptor desconectado, verifique la continuidad mientras activa el interruptor de nivel de Rquido. Reemplace el interruptor, seg6n se requiera. Deje que el nivel de hquido aumente de 3 a 4 pulgadas (76 mm —101 mm) sobre el nivel de activaci6n. no funciona, vea arriba. Cordones de los senores de nivel Desenrede los cordons y asegure el de liquido enredados. funcionamiento libre. LA BOMBA NO Cordones de los senores de nivel Desenrede los cordons y asegure el SE APAGA de liquido enredados. funcionamiento fibre. La bomba esti atascada con aire. Apague la bomba durante aproximadamente un minuto y arranquela nuevamente. Repita hasta que se despeje la obstrucci6n de aire. Si la obstrucci6n de aire persiste en un sistema con tubo con valvula de retenci6n, puede perforarse un agujero de 3/16 ping. (4.8 mm) en el tubo de descarga aproximadamente a 2 pulgadas (51 mm) de la conexi6n de descarga. EI flujo de liquido entrante coincide Podrfa requerirse una bomba mas grande. con la capacidad de descarga de la bomba. LA BOMBA ENTREGA La vilvula de retenci6n esti instalada Verifique la flecha de flujo en la valvula y POCO O NADA invertida, esti obstruida o atascada verifique el funcionamiento de esta. DE LIQUIDO en posici6n cerrada Carga excesiva del sistema. Entrada a la bomba obstruida Tensi6n incorrecta, o conectada incorrectamente. La bomba esti atascada con aire. EI impulsor esti gastado o dafiado. Consulte con el agente. Inspection y despeje, segdn sea requerido. Verifique la rotaci6n, la tensi6n y las conexiones de la bomba. Consulte con un electricista calificado. Consulte la acci6n recomendada, arriba Inspection el impulsor, reemplacelo segun sea necesario. Los controles de nivel de liquido estin Inspection, reajuste o reemplace, defectuosos o intalados incorrectamente. seg6n sea requerido. LA BOMBA CICLA La valvula de retenci6n de la Inspection, repare o reemplace, CONSTANTEMENTE descarga no funciona segun sea requerido. El area de contenci6n de aguas Consulte con el agente. negras es demasiado pequefia Los controles de nivel de liquido estan Inspection, reajuste o reemplace, defectuosos o instalados incorrectamente. seg6n sea requerido. Cantidad excesiva de liquido entrante Consulte con el agente. para una bomba de este tamafio. GARANTIA LIMITADA DEL CONSUMIDOR Para mercaderia vendida para fines personales, familiares o de vivienda, el Vendedor garantiza clue la mercaderia vendida conforme al presente (a excepci6n de membranas, sellos, juntas, materiales de elast6mero, recubrimientos y otras "piezas de desgaste' o consumibles, clue no est6n bajo garantia salvo clue se especificlue to contrario en el presupuesto o formulario de ventas) estar6n libres de defectos en los materiales o mano de obra durante un (1) ano a partir de la fecha de instalaci6n o dieciocho (18) meses desde el c6digo de fecha del producto, de los anteriores el clue ocurra primero, salvo la ley o la documentaci6n del producto (la "Garantia") especifiquen un periodo mayor. Salvo clue la ley establezca to contrario, el Vendedor debe, segun su opci6n y sin costo para el Comprador, reparar o reemplazar cualquier producto clue no cumpla con la Garantia; siempre y cuando el Comprador le avise por escrito al Vendedor de cualquier defecto en el material o mano de obra en un plazo de diez (10) dias desde la fecha de la primera manifestaci6n del defecto o incumplimiento. Bajo la opci6n de reparaci6n o reemplazo, el Vendedor no estar6 obligado a remover o pagar por la remoci6n del producto defectuoso, o instalar o pagar por la instalaci6n del producto reemplazado o reparado y el Comprador sera responsable de todos los dem6s costos, clue incluyen, entre otros, costos de servicio, tarifas de envio y gastos. EI m6todo o el medio de reparaci6n o reemplazo ser6 a total discreci6n del Vendedor. Si el Comprador no cumple con las instrucciones de reparaci6n o reemplazo del Vendedor, esto rescindir6 las obligaciones del Vendedor conforme a la presente Garantia y anular6 la misma. Cualquier parte reparada o reemplazada bajo la Garantia est6 bajo garantia solo por el saldo del periodo de garantia sobre las partes reparadas y reemplazadas. La Garantia est6 condicionada a clue el Comprador le avise por escrito al Vendedor de cualquier defecto en el material o la mano de obra de la mercaderia bajo garantia en un plazo de diez (10) dias desde la fecha de la primera manifestaci6n del defecto. EI Vendedor no tendr6 obligaciones de garantia hacia el Comprador respecto de cualquier producto o partes de un producto clue: (a) hayan sido reparados por terceros clue no sean el Vendedor o sin la aprobaci6n escrita del Vendedor; (b) hayan estado sujetos a usos indebidos, aplicaciones indebidas, negligencia, alteraciones, accidentes o danos fisicos; (c) hayan sido usados de una manera contraria a las instrucciones del Vendedor para la instalaci6n, operaci6n y mantenimiento; (d) hayan sido danados por desgaste, corrosion o ataque quimico habituales; (e) hayan sido danados por condiciones anormales, vibraci6n, falta de cebado correcto u operaci6n sin flujo; (f) hayan sido danados por suministro el6ctrico defectuoso o protecci6n el6ctrica indebida; o (g) hayan sido danados por el use de equipos accesorios no vendidos ni aprobados por el Vendedor. En el caso de productos no fabricados por el Vendedor, no habr6 Garantia del Vendedor; sin embargo, el Vendedor transferir6 al Comprador toda Garantia recibida del proveedor del Vendedor para dichos productos. Politica de Goulds Water Technology sobre ventas an linea a clientes. Los propietarios clue utilizan Internet para encontrar informaci6n sobre sistemas de agua residenciales, sistemas residenciales de aguas residuales, controles y tanclues, pueden descubrir varios sitios clue ofrecen oportunidades de compra directa al consumidor. Los sistemas de aqua y de aguas residuales residenciales son aplicaciones criticas y su diseno es tal clue deben ser instalados por profesionales calificados. Goulds Water Technology posee una extensa red nacional de vendedores y distribuidores, clue incluye revendedores autorizados. Para ver una lista completa de vendedores, revendedores y distribuidores autorizados por Goulds Water Technology, consulte nuestro localizador en: http://goulds.com/sales-service/ No se ofrece ninguna garantia sobre el equipo de Goulds Water Technology adquirido por medio de Internet y esto incluye las opciones basadas en la red a trav6s de distribuidores minoristas no autorizados. Esta politica es necesaria para garantizar clue el equipo de Goulds Water Technology se instale de manera adecuada, en cumplimiento con las leyes, reglas y c6digos aplicables, de manera clue se aborden las preocupaciones de seguridad y el rendimiento apropiado del equipo de Goulds Water Technology. LA GARANTIA ANTERIOR SE FORMULA EN LUGAR DE TODA OTRA GARANTIA EXPRESA. TODAS LAS GARANT(AS IMPL(CITAS, INCLUYENDO, ENTRE OTRAS, LAS GARANT(AS IMPL(CITAS DE COMERCIABILIDAD YAPTITUD PARA UN FIN EN PARTICULAR, SE LIMITAN A UN (1) ANO A PARTIR DE LA FECHA DE INSTALAC16N O DIECIOCHO (18) MESES DESDE EL CODIGO DE FECHA DEL PRODUCTO, DE LOS ANTERIORES EL QUE OCURRA PRIMERO. EXCEPTO SEGON LO DISPUESTO POR LA LEY EN SENTIDO CONTRARIO, EL RECURSO EXCLUSIVO DEL COMPRADOR Y LA RESPONSABILIDAD TOTAL DEL VENDEDOR POR INCUMPLIMIENTO DE CUALQUIERA DE LAS ANTERIORES GARANT(AS SE LIMITAN A REPARAR O REEMPLAZAR EL PRODUCTO Y EN TODOS LOS CASOS SE LIMITARAN AL MONTO PAGADO POR EL COMPRADOR POR EL PRODUCTO DEFECTUOSO. EN NINGUN CASO EL VENDEDOR SERA RESPONSABLE DE CUALQUIER OTRO TIPO DE DANOS Y PERJUICIOS, YA SEAN DIRECTOS, INDIRECTOS, LIQUIDADOS, INCIDENTALES, CONSECUENTES, PUNITIVOS, EJEMPLARES O ESPECIALES, LOS QUE INCLUYEN, ATITULO ENUNCIATIVO Y NO LIMITATIVO, LUCRO CESANTE, PtRDIDA DE AHORROS O INGRESOS ANTICIPADOS, P�RDIDA DE INGRESOS, PtRDIDA DE NEGOCIOS, PtRDIDA DE PRODUCCION, PtRDIDA DE OPORTUNIDADES O PtRDIDA DE REPUTACI6N. Algunos estados no permiten limitaciones sobre la extensi6n de una garantia implicita, por to clue las limitaciones anteriores pueden no corresponder para usted. Algunos estados no permiten la exclusi6n o limitaci6n de danos y perjuicios incidentales o consecuentes, por to clue las exclusiones anteriores pueden no corresponder para usted. La presente garantia le otorga derechos legates especificos, y usted tambi6n puede tener otros derechos clue pueden variar dependiendo del estado. Para realizar un reclamo de garantia, primero verifique con el representante a quien le compr6 el producto o visite xxx.xyleminc.com para buscar el nombre y ubicaci6n del representante m6s cercano clue ofrezca servicio de garantia. t xyem Let's Solve Water Xylem Inc. 2881 East Bayard Street Ext., Suite A Seneca Falls, NY 13148 Telefono: (866) 325-4210 Fax: (888) 322-5877 www.gouldswatertechnology.com Goulds es una marca registrada de Goulds Pumps, Inc. y se utiliza bajo licencia. ® 2016 Xylem Inc. IM038 Revisi6n Numero 6 Febrero 2016 MANUEL D'UTILISATION IM038R06 Pompe di'laceratri-c- mon-ophasee (-b"r'oyeuse) a simple BUILT IN THE USA garniture mecanique ASSEMBLED & TESTED DIRECTIVES D'INSTALLATION, NET WENTRETIEN GOULDS WATERTECHNOLOGY �Y a xylem brand Table des coati SUJET PAGE Consignesde s6curit6..................................................................................................................................................26 Verifications avant installation.....................................................................................................................................26 Levagede la pompe.....................................................................................................................................................26 Systeme de levage optionnel a rail de guidage ou a adaptateur coulissant.....................................................................27 Tuyauterie...................................................................................................................................................................27 Cablageet mise a la terre.............................................................................................................................................27 S61ection et cablage des contacteurs et des tableaux de commande..............................................................................27 Installation..................................................................................................................................................................28 Miseen marche..........................................................................................................:................................................ 29 Tableaux de commande et fonction des contacteurs a flotteur......................................................................................30 Donn6estechniques.....................................................................................................................................................31 Valeurs de resistance d'isolement du moteur................................................................................................................32 Installations types et sch6mas de cablage monophas6s pour pompe simple...................................................................32 Diagnosticdes anomalies.............................................................................................................................................34 Garantielimit6e...........................................................................................................................................................36 n is Num6ro de modele de la pompe : Num6ro de s6rie de la pompe : N° de modele du tableau de commande : D6taillant : No de t616phone du d6taillant Date d'achat : d'installation : Courant (1 0) mesur6 au d6marrage Intensit6 (A) Tension (V) CONSIGNES DE SECURITE AFIN DE PREVENIR LES BLESSURES GRAVES OU MORTELLES ET LES DOMMAGES MATERI- ELS IMPORTANTS, LIRE ETSUIVRE TOUTES LES CONSIGNES DE SECURITE FIGURANT DANS LE MANUEL ET SUR LA POMPE. LE PRESENT MANUEL A POUR BUT DE FACILITER VINSTALLATION ET L'UTILISATION DE LA POMPE ET DOIT ETRE CONSERVE PRES DE CELLE-Cl. Le symbole ci-contre est un SYMBOLE DE SECURITE employe pour signaler A& les mots-indicateurs dont on trouvera la description ci-dessous. Sa presence cert A attirer 1'attention afin d'eviter les bles- sures et les dommages materiels. Previent des risques qui VONT causer des blessures graves, la mort ou des dommages materiels importants. AAVFxnssr Previent des risques qui PEUVENT causer des blessures graves, la mort ou des dommages materiels importants. AATTENTION Previent des risques qui PEUVENT causer des blessures ou des dommages materiels. AVIS: SERT A ENONCER LES DIRECTIVES SPECI- ALES DE GRANDE IMPORTANCE QUE L'ON DOIT SUIVRE. LIRE SOIGNEUSEMENT CHAQUE DIRECTIVE ET AVERTISSEMENT AVANT D'EFFECTUER TOUT TRAVAIL SUR LA POMPE. N'ENLEVER AUCUNE DECALCOMANIE DE SECURITE. AAvwnz8a r I Uinstallation electrique doit etre entiere- ment effectuee par un technicien qualifie. Il faut toujours suivre les prescriptions du code provin- cial ou national de 1'e1ectricite et les reglements locaux. Adresser toute question relative au code a un inspecteur en electricite. Le non -respect du code et des politiques de sante et de securite au travail peut entrainer des blessures et des dommages materiels. Einobservation des directives d'installation fournies par le fabricant peut se traduire par un choc electrique, un incendie, des blessures ou la mort, ainsi que par des dommages materiels, des perfor- mances non satisfaisantes et I'annulation de la garantie du fabricant. Amamsmw r Les pompes standard ne sont pas conques pour les piscines, Peau libre, les liquides dangereux ni les endroits pouvant contenir des gaz inflammables. Ces fluides peuvent etre presents dans les installations de confinement (puits collecteurs, reservoirs ou fosses humides). On doit aerer ces installations suivant les codes locaux. Seules les pompes de classe 1, division 1, peuvent ser- vir dans les liquides dangereux et les endroits pouvant contenir des gaz inflammables. Le nom des organismes de normalisation pertinents figure sur la plaque signaletique de la pompe ou dans les feuillets du catalogue decrivant les pompes en question. jAAvmmsseffxrj Verrouiller la source de courant en position ouverte avant de prodder a Pinstallation ou a Fcntretien de tout dispositif electrique. Le protecteur thermique de certains moteurs de pompe coupe le courant lorsqu'il y a surcharge thermique et le retablit automatiquement, redemarrant ainsi la pompe inopinement. AMICATIONS AVANT INSTALLATION Ouvrir tous les cartons et verifier si le materiel est endommage. Signaler immediatement tout dommage au fournisseur ou au transporteur. Important: on doit toujours verifier si les valeurs nominates inscrites sur la plaque signaletique (intensite, tension, puissance et nombre de phases) conviennent au tableau de commande et a la source de courant. Le compartiment moteur d'un bon nombre de nos pompes a eaux d'egout est rempli d'huile isolante. ST y a des traces d'huile sur la pompe ou si cette derniere a ete entreposee longtemps, verifier le niveau d'huile du compartiment et, si la pompe en est dotee, du logement de garniture. Enlever le bouchon de l'orifice de remplissage du compartiment moteur (sur le dessus de celui-ci), puis verifier le niveau d'huile par 1'orifice. Uhuile devrait seulement recouvrir le moteur. Ne pas trop en mettre pour que Thuile puisse se dilater! Si le niveau d'huile est bas, utiliser de Thuile pour turbines ASTM 150, puis remettre le bouchon. On peut se procurer de Thuile isolante .en contenants de 5 gallons US chez nos distributeurs. On peut aussi en acheter chez un reparateur de moteurs electriques. Les marques d'huiles types sont: Shell Turbo 32, Sunoco Sunvis 932, Texaco Regal R&O 32, Exxon Nuto 32 et Mobil DTE Light. Verifier si 1'ecrou presse-garniture du serre-cable d'alimentation est suffisamment serre. Le couple de serrage est de 75 lbf•po pour les cables de calibre 16 et de 80 lbf-po pour tout autre cable. La garantie ne couvre pas les dommages dus au branchement de la pompe et du tableau de commande a une source de courant dont la tension ou le nombre de phases sont inappropries. Inscrire a titre documentaire les numeros de serie et de mod& de la pompe et du tableau de commande dans les Informations pour le proprietaire, en premiere page. Une fois Pinstallation achevee, remettre le manuel au proprietaire ou Pattacher au tableau de commande. AAvEmssEmEw NE PAS LEVER, TRANSPORTER 0 NI SUSPENDRE LA POMPE PAR LE CABLE D'ALIMENTATION : UENDOMMAGEMENT DU CABLE POURRAIT CAUSER UN CHOC ELECTRIQUE, DES BRULURES OU Les tensions dangereuses LA MORT. peuvent causer un choc Elect que, des brulures et b mor, Lever la pompe par son boulon a oeil ou sa poignee avec un filin ou une chane de grosseur appropriee. NE PAS endommager les cables d'alimentation et de capteur pen- dant la manutention de la pompe. sywkw DE LEvAGE wynoma A RAM ISE GuiDAGE OU A ADAPrATEup. couLissANT Dans le cas de bon nombre de cuves a effluents et de postes de relevement d'eaux d'egout, it est conseille de monter la pompe sur un rail de guidage ou avec un adaptateur coulissant pour pouvoir descendre, retirer, inspecter et entretenir celle-ci plus facilement. La plupart des codes n'autorisent pas le personnel a entrer dans une fosse humide sans la formation ni 1'equipement protecteur appropries. Le rail et 1'adaptateur sont con�us pour faciliter la mise en place et la sortie de la pompe, et ce, sans disjoindre la tuyauterie. Le rail et Padaptateur devraient etre places de fagon a ce que la pompe soit face a Porifice d'arrivee de Pinfluent pour empecher la formation de zones de stagnation et, ainsi, de depots. Le fond du puits collecteur ou de la cuve doit etre plat et suffisamment resistant pour supporter le poids de la pompe et du rail de guidage. AVIS: SUIVRE LES DIRECTIVES FOURNIES AVEC LE RAIL DE GUIDAGE. Afin de reduire les pertes de charge (par frottement) au minimum, la tuyauterie de refoulement devrait etre aussi courte que possible et depourvue d'accessoires et de rac- cords superflus. Son diametre devrait etre au moins egal a celui de 1'orifice de refoulement de la pompe. Prevenir le retour du liquide: poser sur le tuyau de refoulement un clapet de non-retour de calibre adequat. Le retour du liquide peut entramer la «rotation en sens inverse» de la pompe, causant ainsi 1'usure prematuree des garnitures mecaniques et des roulements et produi- sant, au moment du demarrage, un couple accru pouvant abimer le moteur ou Parbre de pompe, ou les deux, et meme forcer certaines pompes monophasees a continuer a tourner en sens inverse. Poser EN AVAL (apres) du clapet de non-retour un robi- net-vanne de calibre approprie pour permettre Pentretien de la pompe, de la tuyauterie et du clapet. Important : avant d'installer la pompe, percer un troupurgeur d'air dans le tuyau de refoulement a environ 51 mm (2 po) au-dessus de l'orifice de refoulement de la pompe, mais avant le clapet de non-retour et a 1'interieur de la fosse humide. Le diametre du trou sera de 4,8 mm (3116 PO) pour les eaux usees contenant des solides. On permettra ainsi au liquide d'entrer dans la pompe par gravite, surtout si Porifice d'aspiration est situe en dessous, et previendra la formation de poches d'air qui empecheraient le pompage du liquide meme si la roue de la pompe tourne. La tuyauterie doit etre supportee correctement pour n'appliquer sur la pompe aucune charge pouvant la deformer. Couvercles et trappes de visite doivent etre assez grands pour permettre Pinspection et 1'entretien de la pompe ainsi que 1'emploi d'un dispositif de levage. BLAGE ET MISE Avis important : lire les Consigns de sicuriti avant de prodder au cdblage. AN'utiliser que du fil torsade en cuivre pour la mise A la terre et 1'alimentation du moteur. Le calibre du fil de terre doit etre au moins egal a celui des fils d'alimentation du moteur, et les fils devraient tous etre chromocodes pour faciliter Pentretien et le diagnostic des anomalies. APoser le fil de terre et les autres fils suivant les prescriptions du code provincial ou national de 1'e1ectricite. AInstaller un sectionneur tout conducteur si le code 1'exige. AVerrouiller la source de courant en position ouverte avant de proceder a Pinstallation ou a 1'entretien de la pompe. ALe nombre de phases et la tension d'alimentation doivent convenir a tout 1'equipement. Un nombre de phases et une tension inappropries annulent la garantie et peuvent causer un incendie et des dom- mages au moteur et au tableau de commande. AChaque jonction de fils doit etre etanche. Si Pon emploie un necessaire de jonction (<< kit o), suivre les directives du fabricant. AAvau u5Em;1 Choisir la boite de jonction du type et de la classe NEMA convenant au type et au lieu d'utilisation. La boite doit assurer une jonction de fils sure et etanche. AAv5mssmBw Stancher les commandes afin d'empecher les gaz d'en deteriorer les composants. AAvmnssEMENT OMETTRE LA MISE A LA TERRE Tension PERMANENTE DE LA POMPE, DU danger e 1 MOTEUR ET DES COMMANDES AVANT LE BRANCHEMENT A LA SOURCE DE COURANT PEUT CAUS- ER UN CHOC ELECTRIQUE, DES BROLURES OU LA MORT. CONTACTEURS A FLOTTEUR TYPES Deux types de contacteurs a flotteur sont utilises avec les pompes dilaceratrices monophasees de 2 hp: commande A simple effet et mecanique a grand deplacement angulaire. Les contacteurs a commande simple effet tels ne peuvent etre relies a la pompe que par le tableau de commande, sinon ils accelereront le fonctionnement cyclique (de- marrage-arret), risquant ainsi de bruler le moteur, son contacteur de demarrage ou le contacteur a flotteur, ou les trois. Avant d'utiliser un contacteur a flotteur a simple effet, connecte a un tableau de commande, voir la section Tableaux de commande et fonction des contacteurs d flot- teur. Les contacteurs a la pompe a flotteur a grand deplacement angulaire modele A2G33 peuvent etre branches par raccordement fixe directement a la pompe. Modeles de ce type de contacteur peuvent etre relies a la pompe par le tableau de commande. La longueur du cable du contacteur, c'est-a-dire la distance entre son point pivot et le boitier du contacteur, constitue la plage de pompage (niveaux demarrage-arret) et regit donc la quantite de liquide pompee a chaque cycle. Voir les figure 1 et 2. REGLAGE DES CONTACTEURS A FLOTTEUR Il n'existe pas de regle absolue pour le reglage des con- tacteurs a flotteur, lequel peut varier d'une installation a Pautre. Regles suggerees : Tous les contacteurs a flotteur devraient etre places sous Porifice d'arrivee de Finfluent! Contacteur d'arret: (1- choix) — le regler pour que le niveau du liquide soit toujours au-dessus du comparti- ment moteur. (2e choix) — le regler pour que le niveau du liquide ne puisse etre a plus de 6 po sous le dessus du compartiment moteur. Contacteur de demarrage : le regler pour que la plage de pompage permette aux pompes de deux (2) hp et plus de fonctionner pendant au moins deux (2) minutes. Le catalogue donne la capacite de chaque cuve en gallons US par pouce de hauteur. Contacteur(s) de pompe secondaire et d'alarme: s'il n'y en a qu'un, le placer plus haut que les contacteurs d'arret et de demarrage, et, s'il y en a deux, on devrait en outre les decaler (v. les illustrations dans la section Tableaux de commande et fonction des contacteurs d flotteur). Essayer d'utiliser tout Fespace de stockage disponible de la cuve, mais prevoir un espace de reserve. SCHEMAS DE CABLAGE DES TABLEAUX DE COMMANDE Des directives et des schemas de cablage sont fournis avec nos tableaux de commande. Utiliser les directives en question conjointement avec celles du present manuel. Uinstallation electrique ne doit etre effectuee que par des techniciens qualifies. Adresser toute question relative aux autres marques de tableau de commande au fournisseur ou au fabricant de ces marques. Notre personnel tech- nique ne dispose pas des schemas ni des informations de depannage des autres marques. DISPOSITIFS D'ALARME Il est recommande de poser un dispositif d'alarme dans toute installation a pompe(s) a eaux usees. De nombreux tableaux de commande standard en sont munis. S'il n'y a pas de tableau de commande, on peut employer un dispositif d'alarme niveau haut, autonome, qui se declenchera si le liquide atteint un niveau trop eleve, avertissant ainsi le personnel d'entretien, qui apportera alors les correctifs appropries. POMPES MONOPHASEES AAS„ E„ff LES POMPES CONNECTEES PAR FICHE DOIVENT L'ETRE A UNE PRISE AVEC TERRE MISE A LA TERRE CORRECTEMENT. S'IL S'AGIT D'UNE POMPE SANS FICHE, NE PAS ENLEVER LE COR - Lm tensions dangereuses DON D'ALIMENTATION NI SON peuvent causer un choc €lectrique, des bnilures SERRE-CABLE NI CONNECTER UN et lamort CONDUIT ALA POMPE. Les pompes dont le bout des fils du cordon d'alimentation est denude peuvent etre branchees par raccordement fixe a un contacteur a flotteur, a un con- tacteur ordinaire monophase ou a un tableau de com- mande pour pompe simple ou double. On doit toujours s'assurer que le contacteur a flotteur convient a l'intensite de marche, a l'intensite maximale au demarrage et a la puissance nominales de la pompe. Sauf indication contraire sur la plaque signaletique, les pompes mono- phasees pour eaux usees sont munies d'une protection d'enroulement contre les surcharges. Voir les figure 1. TABLEAUX DE COMMANDE MONOPHASES Les tableaux de commande viennent en deux versions: pour pompe simple ou pour pompe double. Nos tableaux standard offrent de nombreuses fonctions standard aux- quelles on peut ajouter les options les plus populaires. En outre, nous fournissons des tableaux sur demande dont les fonctions sont beaucoup plus nombreuses que celles des tableaux standard. Les tableaux faits sur demande sont of- ferts en versions variees. On peut adresser toute demande de prix pour ce type de tableau au service a la clientele (Customer Service) par Pentremise d'un distributeur agree. Nos tableaux de commande pour pompe double pos- sedent un circuit imprime muni d'un circuit d'alarme niveau haut standard. Il existe d'autres accessoires standard : contacts _d'alarme secs auxiliaires signalant les alarmes a distance et voyants indicateurs de position pour contacteurs a flotteur. La plupart des tableaux sont en stock et prets a livrer. INSTALLATION DE POMPE(S) STANDARD Fixer a la ou aux pompes le raccord rapide pour le rail de guidage, l'adaptateur coulissant ou la tuyauterie de , refoulement. Le pied d'assise du rail devrait etre assujetti au fond de la fosse humide par des boulons d'ancrage. Effectuer le cablage selon les schemas de cablage des tab- leaux de commande, les prescriptions du code provincial ou national de 1'e1ectricite et les reglements locaux. 7EVITER LES BLESSURES GRAVES: NE PAS S'INTRODUIRE LA MAIN DANS L'ORIFICE D'ASPIRATION DE LA POMPE PENDANT LA VERIFICA- TION DU SENS DE ROTATION. Descendre la ou les pompes dans la fosse humide. Equipements dangereux S'assurer que les contacteurs a flotteur peuvent bouger librement, mais sans pouvoir atteindre la tuyauterie. Installer les ensembles d'evacuation conformement aux codes, aux reglements locaux et aux illustrations de la section Installations types. MISE EN MARCEE Une fois le raccordement de la tuyauterie acheve et veri- fie, on peut mettre la ou les pompes en marche. Contacteurs a flotteur a raccordement fixe — mettre le disjoncteur ou le sectionneur a fusible(s) en circuit. Essayer la pompe en remplissant d'eau la fosse humide jusqu'a ce que la pompe demarre. Si le debit de la pompe est faible ou nul, it y a probablement une poche d'air dans la pompe. Percer alors un trou-purgeur d'air selon les indications de la section Tuyauterie. Verifier la duree de fonctionnement de la pompe pour s'assurer qu'elle est d'au moins two minutes et que la plage de pompage est correcte. Verification du fonctionnement du tableau de commande — remplir d'eau la fosse humide. Essayer d'abord la pompe en mode manuel en pla�ant le commutateur «Hand -Off -Auto» (manuel-arret-au- tomatique) du tableau de commande a Hand. Si la pompe fonctionne bien, Pessayer en mode automatique. Si le debit de la pompe est faible ou nul, c'est qu'il y a probablement presence d'air dans la pompe. Percer alors un trou-purgeur d'air selon les indications de la section Tuyauterie. Faire fonctionner la pompe en mode automatique (Auto) et verifier minutieusement le fonctionnement des con- tacteurs de demarrage, d'arret et d'alarme en remplissant d'eau la fosse humide. Important: omettre de brancher le fil neutre de la source de courant a tout tableau de commande alimente en courant monophase de 230 V empechera le circuit de commande du tableau de fonc- tionner. Le neutre est necessaire pour alimenter (115 V) le circuit de commande. Mesurer 1'intensite et la tension du courant au demar- rage et les inscrire a titre documentaire dans les Informa- tions pour le proprietaire, en premiere page. Comparer Pintensite mesuree a Pintensite maximale indiquee sur la plaque signaletique de la pompe. Si Pintensite mesuree est superieure, en chercher la cause. Uutilisation de la pompe hors de sa courbe de performances, c. -a -d. avec une hauteur de charge trop faible ou avec une basse ou une haute tension, augmentera l'intensite du courant. Le moteur fonctionnera correctement si sa tension d'alimentation se situe dans les limites suivantes : tension nominale figurant sur la plaque signaletique ± 10 %. Les performances obtenues dans ces limites ne seront pas necessairement identiques a celles de la courbe de per- formances correspondant a la tension et a la frequence nominales exactes inscrites sur la plaque signaletique. Apporter les correctifs necessaires avant de continuer. Rearmer le dispositif d'alarme, puis mettre la pompe en mode automatique (Auto) et le circuit de commande du tableau sous tension (interrupteur «Control On -Off» a On). Le systeme est maintenant pret a fonctionner automatiquement. Expliquer le fonctionnement de la pompe et des dis- positifs de commande et d'alarme a Putilisateur, puis lui laisser la documentation ou Pattacher au tableau de com- mande s'il est installe dans un endroit sec, ferme. TABLEAUX DE COMMANDE ET FONCMON DIES coNTAcTiEuRs A FLoTrEuR L'objet de la presente section est d'indiquer le nombre de contacteurs a flotteur requis et le role de chacun dans les systemes d'evacuation des eaux usees types. Le nombre varie selon le type de contacteur : a simple effet ou a grand deplacement angulaire, mais aussi selon le type de tableau de commande: pour pompe simple avec ou sans alarme ou pour pompe double avec alarme. Tableaux de commande pour pompe double a contacteurs a simple effet Trois contacteurs a flotteur SW1 Inferieur Pompes hors fonction SW2 Intermediaire 11e pompe en fonction SW3 Superieur 2e pompe et alarme en fonction Quatre contacteurs a flotteur 2 SW1 Inferieur Pompes hors fonction SW2 Deuxieme (du bas) 11t pompe en fonction SW3 Troisieme (du bas) 2e pompe en fonction SW4 Superieur Alarme en fonction Tableaux de commande pour pompe double a contacteurs a grand deplacement angulaire Trois contacteurs a flotteur SW1 Inferieur 11e pompe en fonction ou les deux hors fonction SW2 Superieur 2e pompe et alarme en fonction Quatre contacteurs a flotteur SWI Inferieur 1- pompe en fonction ou les deux hors fonction SW2 Intermediaire 2e pompe en fonction SW3 Superieur Alarme en fonction Tableaux de commande pour pompe simple a contacteurs a simple effet Trois contacteurs a flotteur avec alarme O SW1 Inferieur Pompe hors fonction SW2 Intermediaire Pompe en fonction SW3 Superieur Alarme en fonction ou hors fonction Deux contacteurs a flotteur sans alarme SW1 Inferieur Pompe hors fonction SW2 Superieur Pompe en fonction Tableaux de commande pour pompe simple a contacteurs a grand deplacement angulaire Deux contacteurs a flotteur avec alarme SW1 Inferieur Pompe en fonction ou hors fonction SW2 Superieur Alarme en fonction ou hors fonction Un contacteur a flotteur sans alarme SWI Pompe en fonction ou hors fonction Entree Alarme (SV Pompe en fonction (S Pompe hor fonction (S' Entn Alarme 2e pomp fonction ( 1 re pomp fonction (! Pompe fonctior Systeme a pompe simple T ement Systeme a pompe double ?ment DONAES TECHMQUES On trouvera les donn6es techniques sur des mod6les particuliers dans le catalogue et 6 I'adresse du site Web inscrite au bas de la premiere page. Les sch6mas de cablage des tableaux de commande sont fournis avec ces derniers. Ten servir conjointement avec les directives du pr6sent manuel pour effectuer le cablage. SERVICE DE LA POMPE Hauteur d'immersion minimale Temperature maximale du liquide Service continu Immersion totale Service continu 40 °C (104 °F) Service intermittent 6 po sous le dessus Service intermittent 60 °C (140 °F) du compartiment moteur Raccordement fixe de I'A2G33 Determination de la plage de pompage BoTte de Raccordement jonction Sourcede RxepourPorn pes courant fonctionnant en 120 ou 230 V Cc= I o, mi Noir Blanc Cbnnetleur du c8ble C! c Pom e Figure 1 Contacteur a flotteur a grand d6placement angulaire Fiche de Fiche -prise la pompe` du contacteur f_ —'Plage de Figure 2 Figure 3 Installation type a contacteur a flotteur a simple effet NIVEAU DE DWARRAGE: 20,3 cm (B po) Figure 4 POIDS -T 15,3 cm (6 po) 15,3 cm (6 po) Valeurs normalement mesur6es on ohms et on mdgohms entre chaque fill et le fill de terre kat du moteur et des fills Valleurs en ohms Valleurs en mdgohms ans cable d'alimentation 20 000 000 (et plus) 20 (et plus) "Moteurreutilisable en fosse 10 000 000 (et plus) 10 (et plus) r. , • willr, , Moteur neuf 2 000 000 (et plus) 2 (et plus) Moteur en bon etat 500 000 A 2 000 000 0,562 Isolation endommagee (la reparer) Moins de 500 000 Moins de 0,5 La valeur de resistance d'isolement varie tres peu d'un moteur A I'autre, peu importent la puissance, la tension d'alimentation et le nombre de phases du moteur. Les valeurs de resistance d'isolement ci-dessus sont tirees de mesures prises avec un megohmmetre et une tension de sortie de 500 V c.c. Les valeurs mesurees peuvent varier si I'on utilise un ohmmetre avec une tension moindre. Communiquer avec le personnel technique de I'usine en pareil cas. INFLUENT POTEAU D'AMENEE DE COURANT — TABLEAU DE COMMANDE BRIDE D'ENTREE CONTACTEUR A MERCURE—ALARME NIVEAU HAUT(EN OPTION) CONTACTEURS A MERCURE VOYANT D'ALARME sz-- TRAPPE DE VISITE A CHARNIERE , o INFLUENT i �--------� , o POTEAU D'AMENEE DE VOYANT D'ALARME COURANT TRAPPE DE VISITE A CHARNINE WENT TABLEAU / EVENT DE COMMANDE _—I^ RAIL DE `'' C. -` KAILUtWI �t "` �TIGEDE TILE DE MAN( UVRE MANCEUVRE DU ROBINET " DU ROBINET' BRIDE D'ENTREE " REFOULEMENT CONTACTEURA s MERCURE —ALARME NIVEA REFOULEMENT ' HAUT(EN OPTION) CLAPET DE CONTACTEURS A CLAPET DE NON-RETOUR MERCURE NON-RETOUR GUIDE DE GUIDE DE POMPE f , POMPE INFERIEUR ''�� INFERIEUR �� POMPE SIMPLE POMPE DOUBLE INSTALLATIONS Schemas de cablage monophases S10020 pour pompe simple TENSION DE 115/230 V c.a. (POUR 115 V c.a., UTILISER L1 ET N ET RELIER L2 ET N AVEC UN FIL) COURANT MONOPHASE DE 60 Hz 51 1 nl- I 1 1 POMPE I I I I 1I NOW: SI LON EMP LOIE UNE SOURCE DE COURANT DE 115 V c.a. SEPARES TERRE I Jt POUR LE CIRCUIT DE COMMANDE, ENLEVER LE FIL J1 RELIANT L1 ET LL1. LA SOURCE DOITTRE MUNIED U NE PROTECTION MAXIMALE DE LL1 15 A. LA CONNECTER LL1 ET N, LE NEUTRE SUR N. LES SYSTEMES FONCTIONNANT EN CIRCUIT DE COMMANDE 230 V REQUIERENT UN SOUS TENSION OU HORS TENSION CABLE D'ALIMENTATION 4 FILS (L7, L2, N ET TERRE). SANS LE NEUTRE (N), LE CIRCUIT DE COMMANDE DU TABLEAU NE POURRATRE MIS SOUS TENSION. MANUEL S1 (AUX.) ARRET , 0 51 -rii- -p o -o- 3 AUTOMATIOUE 1 lbw CONTACTEUR CONTACTEUR DEARRtT DEDtMARRAGE CLIGNOTANT NNEAU HAUT 1 CUGNDIRIR � I Rt AVERTISSEUR CONTACTEUR DE ALARME R2 SONORE LESSAI CONTACTS SECS POUR ff SILENCE R2 ALARME NIVEAU HAUT R2 J1 0 0 0 0 0 0 0 0 0 0' L7 L2 LL1 N 1 2 3 4 5 6 T1 T2 0 0 0 0 0 0 0 0 0 0 0 0 O POUR 115 V c.a., UTILISER I I 1 L1 ET N ET RELIER L2 ET N I I 1 AVEC UN FIL. 1 I I I I I I I I I I 1 1 I I I I I 1 I 115/230 V c.a.O MONOPHASE — — 60 Hz t_____—_ — — — — _ 1 1 1 1 1 I I 1 I 1 ► 1 ► 1 ► 1 1 I I I I 1 I I I I I 1 I I I 1 I I I 1 1 I I 1 I I I 1 I I I Rt' 1 I I 1 1 1 I I I 1 I I I I 1 1 I 1 0 CONTACTS I I I 1 1 I 11 SECS I I I I I I I QQQ I I I 6 1 CONTACTEUR I I I IDEALARME O I 1 I 1 POMPE I j 1 COMACfEUR I I � DEDEMARRAGEI I I CONTACTEUR I DE ARRET DIAGNOSTIC AAVEMSEMENT OMETTRE DE VERROUILLER LA SOURCE DE COURANT EN POSITION OUVERTE AVANT Tension D'EFFECTUER TOUT TRAVAIL D'ENTRETIEN SUR LA POMPE PEUT CAUSER UN CHOC dangereuse ELECTRIQUE, DES BRULURES OU LA MORT. ANOMALIES CAUSES PROBABLES CORRECTIFS RECOMMANUS NON-FONCTIONNEMENT DU MOTEUR NOTA: si le disjoncteur ne cesse de s'« OUVRIR », NE PLUS le rearmer. S'adresser A un electricien. a) Mode manuel Protecteur thermique du moteur declenche Disjoncteur ouvert ou fusible saute Roue bloquee ou grippee Cable d'alimentation endommage Mauvaise connexion dans le tableau de commande Laisser le moteur refroidir. Verifier si la hauteur &immersion est suffisante. Enlever les debris du corps de pompe et de la roue. En determiner la cause et s'adresser a un electricien. Mesurer le courant (A) consomme par le moteur. Si l' intensite est au moins deux fois plus elevee que celle qui figure sur la plaque signaletique de la pompe, la roue est grippee, ou bien les roulements ou 1'arbre du moteur sont endommages. Enlever les debris du corps de pompe et de la roue. Consulter le detaillant. DEBIT DE REFOULEMENT Clapet de non-retour pose a 1'envers, Verifier l'orientation de la fleche sur le clapet de non- FAIBLE OU NUL obstruct ou coince en position fermee retour et le fonctionnement de ce dernier. Hauteur de charge trop elevee du systeme Consulter le detaillant. Entree de pompe obstruee Inspecter et degager 1'entree au besoin. Connexions ou tension Verifier le sens de rotation de la pompe, la tension et inapproprictes le cablage. Consulter un electricien. Poche d'air dans la pompe Voir le correctif recommande pertinent ci-dessus. Roue usee ou endommagee Inspecter la roue et la remplacer au besoin. Contacteurs a flotteur Inspecter, regler ou remplacer les contacteurs au besoin. defectueux ou mal places CYCLE DE Clapet de non-retour defectueux Inspecter, reparer ou remplacer le clapet au besoin. La valeur de resistance mesuree entre les fils b) Mode automatique Fil neutre non connecte au d'alimentation et le fil de terre devrait etre infinie. Contacteurs a flotteur tableau de commande Si elle n'est pas appropriee, appeler un electricien. Mauvaise connexion dans le Inspecter le cablage du tableau de commande. a celui de la pompe tableau de commande Appeler un electricien. Contacteur a flotteur defectueux Debrancher le contacteur a flotteur et en verifier la NOTA : verifier si la pompe continuite en 1'actionnant. Le remplacer au besoin. peut fonctionner en mode manuel d'abord. Si oui, la commande automatique ou Liquide trop bas pour Laisser le liquide monter de 76 a 101 mm (3 a 4 po) le cablage sont defectueux. actionner les commandes au-dessus du niveau de demarrage. Dans la negative, voir les Cables de contacteur a Demeler les cables de contacteur a flotteur et s'assurer indications ci-dessus. flotteur enchevftres que les contacteurs peuvent bouger librement. NON -ARF& DE Cables de contacteur Demeler les cables de contacteur a flotteur et s'assurer LA POMPE a flotteur enchevetres que les contacteurs peuvent bouger librement. Poche d'air dans la pompe Arreter la pompe pendant environ une minute, puis la remettre en marche. Mpeter ('operation jusqu'a ce que la poche d'air s'elimine. Si le probleme persiste et que le tuyau de refoulement comporte un clapet de non-retour, on peut percer un trou-purgeur d'air de 4,8 mm 0116 Po) de diarnkre dans le tuyau a environ 51 mm (2 po) en aval de 1'orifice de refoulement de la pompe. Debit de ('influent egal E faut peut-etre une pompe plus puissante. A celui de la pompe DEBIT DE REFOULEMENT Clapet de non-retour pose a 1'envers, Verifier l'orientation de la fleche sur le clapet de non- FAIBLE OU NUL obstruct ou coince en position fermee retour et le fonctionnement de ce dernier. Hauteur de charge trop elevee du systeme Consulter le detaillant. Entree de pompe obstruee Inspecter et degager 1'entree au besoin. Connexions ou tension Verifier le sens de rotation de la pompe, la tension et inapproprictes le cablage. Consulter un electricien. Poche d'air dans la pompe Voir le correctif recommande pertinent ci-dessus. Roue usee ou endommagee Inspecter la roue et la remplacer au besoin. Contacteurs a flotteur Inspecter, regler ou remplacer les contacteurs au besoin. defectueux ou mal places CYCLE DE Clapet de non-retour defectueux Inspecter, reparer ou remplacer le clapet au besoin. FONCTIONNEMENT Installation de confinement des Consulter le detaillant. REPETE SANS AFJ& eaux d'egout trop petite Contacteurs a flotteur Inspecter, regler ou remplacer les contacteurs au besoin. defectueux ou mal places Debit de l'influent superieur Consulter le detaillant a celui de la pompe �� t GARANTIE LIMITEE DU CONSOMMATEUR Pour les biens vendus a des fins personnelles, familiales ou domestiques, le Vendeur garantit que les biens achet6s ci-apr6s (avec 1'exception des membranes, joints, joints d'6tanch6it6, mat6riaux blastomeres, rev6tements et autres «pieces d'usure» ou consommables qui ne sont pas garantis sauf si autrement indiqu6 dans la proposition ou le formulaire de ventes) seront exempts de tout d6faut de mat6riaux ou de fabrication pour une p6riode de un (1) an a partir de la date d'installation ou 18 (18) moil a partir du code de date du produit, selon la premiere 6ventualit6, a moins qu'une p6riode plus longue soit pr6vue par la loi ou spdcifi6e dans la documentation du produit (la ((Garantie))). Sauf mention contraire dans la loi, le Vendeur devra, a sa discr6tion et sans frais pour I'Acheteur, soit r6parer soit remplacer tout produit qui ne se conforme pas avec la Garantie en autant que I'Acheteur donne un avis 6crit au Vendeur de tous d6fauts de mat6riaux ou de fabrication en dedans de dix (10) jours de la date lorsque tous d6fauts ou non conformit6 se manifeste. Que ce soit pour une r6paration ou un remplacement, le Vendeur ne sera pas oblig6 d'enlever ou de payer pour le retrait du produit d6fectueux ou d'installer ou de payer pour ('installation du produit remplac6 ou r6par6 et I'Acheteur sera responsable de tous les autres coots, incluant mais sans s'y limiter, les touts de service, les frais et les d6penses de transport . Le Vendeur aura une absolue discr6tion en ce qui concerne la m6thode ou les moyens de r6paration ou de remplacement. Le non -respect de I'Acheteur de se conformer aux directives de r6paration ou de remplacement du Vendeur mettra fin aux obligations du Vendeur sous cette Garantie et annulera cette Garantie. Toutes les pieces r6par6es ou remplac6es sous la Garantie sont garanties seulement pour le restant de la p6riode de garantie sur les pieces qui ont 6t6 r6par6es ou remplac6es. La Garantie est conditionnelle 6 ce que I'Acheteur donne un avis 6crit au Vendeur de tous d6fauts dans les mat6riaux ou la fabrication des biens garantis en dedans de dix (10)jours de la date lorsque tous d6fauts se sont manifest6s. Le Vendeur n'aura aucune obligation de garantie a I'Acheteur en ce qui a trait 6 tout produit ou toutes pieces qui ont 6t6 : (a) r6par6s par des tiers autre que Ie Vendeur ou sans ('approbation 6crite du Vendeur; (b) sujets 6 une mauvaise utilisation, un usage impropre, une alt6ration, un accident, ou dommage physique; (c) utilis6s de maniere contraire aux instructions du Vendeur pour ('installation, le fonctionnement ou 1'entretien; (d) endommag6s par I'usure ordinaire, la corrosion, ou une attaque chimique; (e) endommag6s 6 cause de conditions anormales, de vibrations, d'un manque dans une mise en service appropri6e, ou d'un fonctionnement sans d6bit; (f) endommag6s 6 cause d'une alimentation 61ectrique d6fectueuse ou de protection 6lectrique inappropri6e; ou (g) endommag6s suite a ('utilisation d'accessoires non vendus ou approuv6s par le Vendeur. Dans tous les cas de produits non fabriqu6s par le Vendeur, it n'y a aucune garantie de la part du Vendeur; toutefois, le Vendeur prolongera 6 I'Acheteur toute garantie reque du fournisseur du Vendeur de tels produits. Politique de Goulds Water Technology concernant les venter an ligne aux clients. Les propri6taires de maison utilisant ('Internet pour trouver des informations concernant les systemes d'eau r6sidentielle, les syst6mes d'eaux us6es r6sidentielles, les commandes et les r6servoirs peuvent d6couvrir plusieurs sites offrant la possibilit6 de faire des achats directs. Les systemes d'eau et d'eaux us6es r6sidentielles sont des applications trios importantes conques pour etre install6es par des professionnels qualifi6s. Goulds Water Technology dispose d'un vaste r6seau national de distributeurs et de concession nai res ainsi que de revendeurs agrees. Pour obtenir une liste compl6te des distributeurs reconnus ainsi que des concessionnaires et des revendeurs agr66s de Goulds Water Technology, veuillez consulter notre localisateur a : http://goulds.com/sales-service/ Aucune garantie nest offerte sur 1'6quipement Goulds Water Technologie achet6 sur ('Internet, incluant les options bashes sur le Web provenant de d6taillants non autorisds. Cette politique est n6cessaire afin d'assurer que 1'6quipement de Goulds Water Technology est correctement install6, conform6ment aux lois, reglements et codes en vigueur, de maniere qui couvre les pr6occupations de s6curit6 et la bonne performance de 1'6quipement de Goulds Water Technology. LA GARANTIE QUI PRECEDE EST FOURNIE A LA PLACE DE TOUTES AUTRES GARANTIES EXPRESSES. TOUTES LES GARANTIES IMPLICITES, Y COMPRIS MAIS SANS S'Y LIMITER LES GARANTIES IMPLICITES DE VALEUR MARCHANDE ET D'ADAPTABILITE POUR UN BUT PARTICULIER, SONT LIMITEES A UN (1) AN DE LA DATE DE UINSTALLATION OU DIX-HUIT (18) MOIS DU CODE DE DATE DU PRODUIT, SELON LA PREMIERE EVENTUALITE. SAUF LORSQU'AUTREMENT REQUIS PAR LA LOI, UUNIQUE RECOURS DE UACHETEUR ET LA RESPONSABILITE GLOBALE DU VENDEUR POUR VIOLATION DE TOUTES GARANTIES QUI PRECEDENT SONT LIMITES A LA REPARATION OU AU REMPLACEMENT DU PRODUIT ET NE SERONT EN AUCUN CAS LIMITES AU MONTANT PAYE PAR UACHETEUR POUR LE PRODUIT DEFECTUEUX. DANS AUCUN CAS LE VENDEUR NE SERA RESPONSABLE DE TOUTE AUTRE FORME DE DOMMAGES, OWLS SOIENT DIRECTS, INDIRECTS, LIQUIDES, ACCESSOIRES, PUNITIFS, EXEMPLAIRES OU DOMMAGES SPECIAUX, INCLUANT MAIS SANS S'Y LIMITER LA PERTE DE PROFIT, LA PERTE D'ECONOMIES OU DE REVENUS ANTICIPES, LA PERTE DE REVENU, LA PERTE COMMERCIALE, LA PERTE DE PRODUCTION, LA PERTE D'OPPORTUNITE OU LA PERTE DE REPUTATION. Certaines provinces ne permettent pas de limiter la durde des garanties implicites, par cons6quent la limite ci-dessus peut ne pas.sappliquer 6 vous. Certaines provinces ne permettent pas 1'exclusion ou la limite de dommages accessoires ou indirects, par cons6quent les exclusions ci-dessus peuvent ne pas sappliquer 6 vous. Cette garantie vous confere des droits juridiques sp6cifiques, et vous pouvez 6galementjouir d'autres droits qui peuvent varier d'une juridiction 6 I'autre. Pour faire une r6clamation de garantie, v6rifier d'abord avec le concessionnaire o6 vous avez achet6 le produit ou visiter www.xyleminc.com pour le nom et 1'emplacement du concessionnaire le plus pr6s qui offre un service de garantie. )cyte m Xylem Inc. Let's Solve Water 2881 East Bayard Street Ext., Suite A Seneca Falls, NY 13148 T616phone: (866) 325-4210 T616copie: (888) 322-5877 www.gouldswatertechnology.com Goulds est une marque d6pos6e de Goulds Pumps, Inc. et est utilise sous le permis. ® 2016, Xylem Inc. IM038 Revision numbro 6 Frier 2016 p F-11 GRUNDFOSV% Submittal Data PROJECT: UNIT TAG: QUANTITY: TYPE OF SERVICE: REPRESENTATIVE: SUBMITTED BY: DATE: ENGINEER: APPROVED BY: DATE: CONTRACTOR: ORDER NO.: DATE: H [ft] 30 25 20 15 10 5 0 P17 16% 00 1'07 'rsMa SIRE TION Z# iH ] EHt11E0 U KV41LA 242016 rRM7ER GRUNDFOSV% 6.700 — 6 28 I 7.5 0 0.75 X 8 Submittal Data 16%1a6Der1aIs: Pump housing: DIN W. -Nr. ASTM A48 CLASS25B Impeller: DIN W. -Nr. ASTM A48 CLASS25B Motor: DIN W. -Nr. ASTM A48 CLASS25B 160x240 217 Company name: A/ Created by: G R U N ®F0.S��` Phone: Date: 6/24/2016 Position Count Description 1 SLV.30.A40.18.EX.4.61J Product photo could vary from the actual product Product No.: 96971945 Non -self -priming, single -stage, centrifugal pump designed for handling wastewater, process water and unscreened raw sewage. The pump is designed for intermittent and continous operations in submerged installation. The efficient SuperVortex impeller provides passage of long fibres and solids up to 3 1/8 in and is suitable for wastewater with a dry matter content of up to 5 %. A unique stainless-steel clamp assembling system enables quick and easy disassembly of the pump from the motor unit for service and inspection. No special tools are required. Pipework connection is via a ANSI flange. The pump is explosion -proof. Controls: Moisture sensor: with moisture sensors Water -in -oil sensor: without water -in -oil sensor Liquid: Pumped liquid: any viscous fluid Maximum liquid temperature: 104 °F Density: 62.29 Ib/ft' Technical: Type of impeller: Super Vortex Maximum particle size: 3 1/8 in Primary shaft seal: SIC/SIC Secondary shaft seal: CARBON/CERAMICS Approvals on nameplate: CSA Curve tolerance: ANSI/HI 11.6:2012 Grade 3B Materials: Pump housing: DIN W. -Nr. ASTM A48 CLASS25B Impeller: DIN W. -Nr. ASTM A48 CLASS25B Motor: DIN W. -Nr. ASTM A48 CLASS25B Installation: Maximum ambient temperature: 104 °F Flange standard: ANSI Pump inlet: 80 Pump outlet: 100 Maximum installation depth: 65.62 ft Frame range: B Electrical data: Power input - P1: 1.7 kW Printed from Grundfos Product Center [2016.04.035] 3l7 Company name: Created by: �r�•• R U N D �O . �`!'` Phone: V Date: 6/24/2016 Position Count Description Rated power - P2: 1.743 HP Main frequency: 60 Hz Rated voltage: 3 x 208-230/460 V Voltage tolerance: +10/-10% Max starts per. hour: 20 Rated current: 6.9-6.4 A Rated speed: 1750 rpm Motor efficiency at full load: 76.2% Motor efficiency at 3/4 load: 74.4% Motor efficiency at 1/2 load: 69.6% Number of poles: 4 Start. method: star/delta Enclosure class (IEC 34-5): IP68 Insulation class (IEC 85): H Length of cable: 33 ft Cable type: SEOOW 600V Others: Net weight: 206 Ib Printed from Grundfos Product Center [2016.04.035] an Company name: Created by: FQ 5 N Phone: G R U N D Date: 6/24/2016 96971945 SLV.30.A40.18.EX.4.61J 60 Hz eta NPSH [ft] Printed from Grundfos Product Center [2016.04.035] 5/7 Company name: A / Created by: G R U N D FO S SIA Phone: General information: Product name: SLV.30.A40.18.EX.4.61J ....... .......... ........... Product No.: 96971945 -�- __... _... _ ...— Price: On request Technical: ANSI _ _ .............. ......... Max flow: ......... - 304 US gpm Head max: .... 28.22 ft _1111. Type of impeller: _ Super Vortex Maximum particle size: 3 1/8 in Primary shaft seal: SIC/SIC Secondary shaft seal CARBON/CERAMICS Approvals on nameplate: CSA Curve tolerance: ANSI/HI 11.6:2012 Grade 3B Materials: ANSI Pump housing: DIN W. -Nr. ASTM A48 Pump outlet: CLASS25B Impeller: __1111.. .. _............._.... DIN W. -Nr. ASTM A48 Inst dry/wet:SUBMERGED CLASS25B .....____.... _................ Motor. ........... _ 1111..._ .................. DIN W. -Nr. ASTM A48 _. .._.-... Frame range. CLASS25B Installation: Maximum ambient temperature: 104 °F Flange standard: ANSI ...._.............. . _......... Pump inlet: ... _1111 80 Pump outlet: ......... 100 ....... Maximum installation depth: ......... 65.62 ft Inst dry/wet:SUBMERGED 3 x 208-230/460 V ...... ........ ......... Installation: --__--------.------- ------- VERTICAL _. .._.-... Frame range. __.. -_- .-_- ........... 1111._ B Liquid: Pumped liquid: any viscousI fluid ......1111... ......... Maximum liquid temperature: 104 °F __.......__._.......__ ...................... Density: 62.29 Ib/ft' Electrical data: Power input - P1: ....._._................................................. 1.7 kW ......... Rated power - P2: 1.743 HP _ __._.._ _1111.. Main frequency: 11 .. 60 Hz Ra11 ted voltage: 3 x 208-230/460 V ...... ........ ......... Voltage tolerance: +10/-10% Max starts per. hour: 20 Rated current: 6.9-6.4 A Rated speed:1750 _ .......... ... _1111 rpm Motor efficiency at full load: 76.2% Motor efficiency at 3/4 load: 74.4 _1111._ _.._ Motor efficiency at 1/2 load: ................ _ 69.6% Numbe1.r of poles: 4 .........111.1 Start. method: ........... star/delta Enclosure class (IEC 34-5): _1111.. IP68 ..1111. .1__1_...1 Insulation class (IEC 85): .............. H .1-1.1...1 ..... _ Length of cable: _ - ... _.. ........... _1111.._ ............ 33 ft - 1111 ... 1111-... . Cable type. 111 .1-11.1.1 .... _....... .. SEOOW 600V 1-111. 1111 Controls: Date: 6/24/2016 P [HF ta it JPSH [ftl Printed from Grundfos Product Center [2016.04.035] sl7 Company name: Created by: G R V N D F®S:t Phone: 's" . Additional 1/0: External Moisture sensor: with moisture sensors Water -in -oil sensor: without water -in oil sensor ........... Others: Net weight: 206 Ib Date: 6/24/2016 Printed from Grundfos Product Center [2016.04.035] 7/7 FILO 510020 NEMA 4X OUTDOOR TYPICAL GUIDE RAIL BASIN KIT CONTROL PANEL GRINDER PACKAGES CODE TECHNICAL BROCHURE BGPGS R1 FEATURES Pump: Capacities: to 41 GPM, Total Heads: to 95' TDH Discharge: 11/4" NPT Temperature: 104° F continuous, 140° F intermittent. Single mechanical seal: silicon carbide rotary/silicon carbide stationary, 300 series stainless steel metal parts, BUNA-N elastomers. Rotating cutter and cutter ring: 440 C stainless steel, hardened to 55 - 60 Rockwell C. Motor: Single phase: 2 HP, 60 Hz, 3450 RPM, 208/230V, capacitor start with on winding thermal protector. Class F insulation Shaft: 300 series stainless steel threaded design. Bearings: ball bearings upper and lower. Power cord: 20 feet standard 14/3 STOW. See BRGS2012 pump bulletin for additional data. AGENCY LISTINGS cCTested to UL 778 and CSA 22.2 108 Standards SR• By Canadian Standards Association L us File #LR38549 RECEIVED � CITY OF 1"IiKVJILA COJUN 24 2016 RRE TION LTR# PERMIT CENTER JUL O 1 2016 Cif f Tukwila �/� � �BUI ING DIVISION RECEIVED N 2 8 2016 TUKWILA PUBLIC WORKS GOULDS VVATER TECHNOLOGY a xylem brand Pump/Control Kit Order No. Description Simplex SIMRGSKTN4* (1) RGS2012 2HP, 230 V, single phase, pump (1) S10020 Simplex outdoor control panel (3)A2D23W Mechanical level switch 41<639 Cast iron pump leg (set of 3) Duplex DUPRGSKTN4* (2) RGS2012 2 HP, 230 V, single phase, pump (1) D10020 Duplex outdoor control panel (3)A2D23W Mechanical level switch 4K639 Cast iron pump leg (set of 3) * For indoor panel delete suffix "N4", SIMRGSKT includes a S1 0020N1 panel. DUPGRSKT includes a D10020N1 panel. PUMP AND CONTROL DATA GRINDER PUMP PACKAGES A complete simplex or duplex installation consists of a simplex or duplex pump kit AND a simplex or duplex basin kit. Choose the simplex or duplex basin kit from the chart on the following pages to best suit your installation needs and make sure it is included in your order. Both pump/control kit and basin kit must be ordered for a complete installation. Component HP Volts Phase RPM Maximum Amps LRA Full Load Motor Efficiency Resistance Start Line' Line Power Fuse/ Weight Cable Circuit (lbs.) Breaker RGS2012 2 1 208/230 1 1 3450 15 59 70 2.47 1 0.6 14/3 30 75 510020 Simplex Outdoor WX Panel 20 Maximum Amps S10020N1 Simplex Indoor N1 Panel 20 Maximum Amps D10020 Duplex Outdoor WX Panel 20 Maximum Amps D10020N1 Duplex Indoor N1 Panel 20 Maximum Amps METERS 30 rt 2s 20 x is to 0 2.5 S•o 7.5 too ms/hs CAPAC17Y m A 1'/: minimum discharge pipe requires a minimum flow of 10 gam to maintain a 2 ftisec, scouring w:locity. Flows less than 10 gpm will allow solids to settle in the pipe. PAGE 2 TYPICAL INSTALLATION SOLID FIBERGLASS COVER 3" NPTTHREADED VENT FLANGE FIELD INSTALLED 304 STAINLESS STEEL FLOAT BRACKET WITH (3) GRIPS 11k" ELECTRICAL GROMMET WITH 1'k" PVC PIPE ELEV 4" INLET GROMMET FIELD INSTALLED INV. ELEV A HIGH ELEV' LEVEL ELEV 0 ALARM PUMP ON hELEV PUMP OFF ELEV 8 FIBERGLASS 0— A{JTI-FLOAT ROUND FLANGE" Ll BRASS QUICK DISCONNECT GATE VALVE /a"7x19 STAINLESS STEEL LIFTING CABLE -X"304 STAINLESS STEELVALVE EXTENSION HANDLE INDUSTRIAL ENAMELED STEEL DISCHARGE COUPLING 4- INV. ELEV BALL CHECK VALVE J 11 DISCHARGE PIPE '�. CAST IRON x;+. i "�9r • .PUMP LEGS � ,•.gf:' .. a b�' is Wastewater BASIN KITS (Each pump kit requires one of the following basin kits to complete the Residential Pump Package.) * Basins are not pre -drilled for 1.5" electrical grommet or for 4" inlet grommet. Parts are shipped loose. Installer must drill holes for grommets. Guide Rail Equipped Basin Installation (pump is suspended by its discharge) Simplex Duplex • 24" diameter fiberglass basin with integral anti- • 36" diameter fiberglass basin with integral anti - floatation ring. floatation ring. • Stainless steel hardware. • Stainless steel hardware. • Grass green solid fiberglass cover. • Grass green solid fiberglass cover. • 1.5" electrical grommet. * • 1.5" electrical grommet. • 4" inlet grommet. * • 4" inlet grommet. * • Brass quick disconnect coupling. • (2) Brass quick disconnect couplings. • Schedule 40 galvanized steel discharge pipe. • Schedule 40 galvanized steel discharge pipes. • Cast iron ball type check valve. • (2) Cast iron ball type check valves. • Bronze gate valve. • (2) Bronze gate valves. •'/4" stainless steel pump lifting cable 9(2)1/4" stainless steel pump lifting cables. • Pump slide rail system complete with PVC guide • Pump slide rail system complete with dual pipe pipe and integral stainless steel guide bracket for stainless steel guide rail system assembly for those those installations requiring a guide rail type system. installations requiring a guide rail type system. r 1p �4 _001 S4UGR48 Kit No. Discharge Piping (SS) Slide Rail Basin Dia. Basin Depth "A" Dim. Stainless S4UGR48 1.25" steel guide 24" 48" (tall) 20" bracket and PV S4UGR84 1.25" pipeide 24" 84" (tall) 42" D4UGR48 Kit No. Discharge Piping (SS) Slide Rail Basin Dia. Basin Depth A" Dim. Stainless D4UGR48 1.25" steel guide 36" 48" (tall) 20" bracket and PV de D4UGR84 1.25" pipe 36" 84" (tall) 42" PAGE 3 BASIN KITS (Each pump kit requires one of the following basin kits to complete the Residential Pump Package.) * Basins are not pre -drilled for 1.5" electrical grommet or for 4" inlet grommet. Parts are shipped loose. Installer must drill holes for grommets. Non -Guide Rail Equipped Basin Installation (pump stands on its own feet) Simplex • 24" diameter fiberglass basin with integral anti - floatation ring. • Stainless steel hardware. • Grass green solid fiberglass cover. • 1.5" electrical grommet. • 4" inlet grommet. * • Brass quick disconnect coupling with stainless steel pull rod. • Schedule 80 PVC discharge pipe. • PVC ball type check valve. • PVC gate valve. • 1/4" stainless steel pump lifting cable. S4NGRD48 Duplex • 36" diameter fiberglass basin with integral anti - floatation ring. • Stainless steel hardware. • Grass green solid fiberglass cover. • 1.5" electrical grommet. • 4" inlet grommet. * • (2) brass quick disconnect couplings with stainless steel pull rods. • Schedule 80 PVC discharge pipes.. • (2) PVC ball type check valves. • (2) PVC gate valves. • 1/4" stainless steel pump lifting cable. A A f i -i 1 f ' 3 D4NGRD48 Krt No. Piping (PVC) Discharget24" Basin Diam. Basin Depth "A" Dim. S4NGRD48 1.25"48" 36" (tall) 20" S4NGRD84 1.25"84" 36" (tall) 42" S2NGRD48 2.00"48" 36" (tall) 20" S2NGRD84 2.00"84" 1 36" 1 (tall) 1 42" ylem Let's Solve Water Kit No. Discharge Piping (PVC) Basin Diam. Basin Depth `A" Dim. D4NGRD48 1.25" 36" 48" (tall) 20" D4NGRD84 1.25" 36" 84" (tall) 42" D2NGRD48 2.00" 36" 48" (tall) 20" D2NGRD84 2.00" 1 36" 1 84" (tall) 1 42" Xylem, Inc. 2881 East Bayard Street Ext., Suite A Seneca Falls, NY 13148 Phone: (866) 325-4210 Fax: (888) 322-5877 www.xyleminc.com/brands/gouldswatertechnology Goulds is a registered trademark of Goulds Pumps, Inc. and is used under license. ® 2012 Xylem Inc. BGPGS R1 April 2012 Job Name - Job Location Engineer — Approval — Series LF009 Reduced Pressure Zone Assemblies Sizes: t/4" — 3" (8 — 80mm) Series LF009 Reduced Pressure Zone Assemblies are designed to protect potable water supplies in accordance with national plumbing codes and water authority requirements. This series can be used in a variety of installations, including the prevention of health hazard cross - connections in piping systems or for containment at the service line entrance.The LF009 features Lead Free' construction to comply with Lead Free' installation requirements. This series features two in-line, independent check valves, captured springs and replaceable check seats with an intermediate relief valve. Its compact modular design facilitates easy maintenance and assem- bly access. Sizes '/4" — 1 " (8 — 25mm) shutoffs have tee handles. Features • Single access cover and modular check construction for ease of maintenance • Top entry - all internals immediately accessible • Captured springs for safe maintenance • Internal relief valve for reduced installation clearances • Replaceable seats for economical repair • Lead Free' cast copper silicon alloy body construction for durability '/4" — 2" (8 — 50mm) • Fused epoxy coated cast iron body 2'/2" and 3" (65 and 80mm) • Ball valve test cocks — screwdriver slotted '/4" — 2" (8 — 50mm) • Large body passages provides low pressure drop • Compact, space saving design • No special tools required for servicing Specifications A Reduced Pressure Zone Assembly shall be installed at each potential health hazard location to prevent backflow due to backsiphonage and/ or backpressure. The assembly shall consist of an internal pressure differential relief valve located in a zone between two positive seating check modules with captured springs and silicone seat discs. Seats and seat discs shall be replaceable in both check modules and the relief valve. There shall be no threads or screws in the waterway exposed to line fluids. Service of all internal components shall be through a single access cover secured with stainless steel bolts. Body and shutoffs shall be constructed using Lead Free' cast copper silicon alloy materials. Lead Free' reduced pressure zone assembly shall comply with state codes and standards, where applicable, requiring reduced lead content. The assembly shall also include two resilient seated isolation valves, four resilient seated test cocks and an air gap drain fitting. The assem- bly shall meet the requirements of: USC; ASSE Std. 1013; AWWA Std. C511; CSA B64.4. Shall be a Watts Series LF009. ES-LF009 Contractor Approval Contractor's P.O. No. RECEReprIVED MAR 21 2016 CORRECTION TUKWILA LTR# PUBLIC WORKS 00• APR 13 p • Test Cock No. 3 2016 est Cock No. 4 Ball Type Test Cocks Test Cock TS of Tukwila I NG DIVISION First CheckCheck %B�/1 Module�u .f �� :,fi e; �Q \C Module A.i'sam *I_..... Assembly .■ Ir �■c R.P. Zone— Relief _ Relief Valve Assembly f Water Outlet RECEIVED CITY C1:= WKWILA Now Available WattsBox Insulated Enclosur`/A R 17 2016 For more information, send for literature ES -WB. PERMIT CENTER Inquire with governing authorities for local installation requirements NOTICE The information contained herein is not intended to replace the full product installation and safety information available or the experience of a trained product installer. You are required to thoroughly read all installation instructions and product safety information before begin- ning the installation of this product. "The wetted surface of this product contacted by consumable water contains less than 0.25% of lead by weight. Watts product specifications in U.S. customary units and metric are approximate and are provided for reference only. For precise measurements, please contact Watts Technical Service. Watts reserves the right to change or modify product design, construction, specifications, or materials with- XXIWAM out prior notice and without incurring any obligation to make such changes and modifications on Watts products previously or subsequently sold. 1(7 1 &.4- 0 l I Available Models: 1/4" - 2" (8 - 50mm) Suffix: QT - quarter -turn ball valves S - strainer LF - without shutoff valves PC - internal polymer coating Prefix: U - union connections Available Models: 21/2" - 3" (65 - 80mm) Suffix: NRS - non -rising stem resilient seated gate valves OSY - UL/FM outside stem and yoke resilient seated gate valves S -FDA - FDA epoxy coated strainer QT -FDA - FDA epoxy coated quarter -turn ball valves LF - without shutoff valves Note: The installation of a drain line is recommended. When install- ing a drain line, an air gap is necessary (see ES -AG). Materials: 1/4" - 2" (8 - 50mm) Lead Free' cast copper silicon alloy body construction, silicone rubber disc material in the first and second check plus the relief valve. Replaceable polymer check seats for first and second checks. Removable stainless steel relief valve seat. Stainless steel cover bolts. Standardly furnished with NPT body connections. Model LF009QT furnished with quarter -turn, full port, resilient seated, Lead Free' cast copper silicon alloy body ball valve shutoffs. Materials: 2'/2" and 3" (65 - 80mm) • (FDA approved) Epoxy coated cast iron unibody with plastic seats • Relief valve with stainless steel seat and trim • Lead Free cast copper silicon alloy body ball valve test cocks Air Gaps and Elbows Pressure / Temperature Sizes 1/4" - 2" (8 - 50mm) Suitable for supply pressure up to 175psi (12 bar). Water temperature: 33°F -180°F (0.5° - 75°C). Sizes 21/2" and 3" (65 and 80mm) are suitable for supply pressures up to 175psi (12.1 bar) and water temperature at 110°F (43°C) continuous, 140°F (60°C) intermittent. Standards USC ASSE No. 1013 AWWA C511 CSA B64.4 IAPMO File No. 1563. H55E 0 S P ® UPC Approvals ASSE, AWWA, CSA, IAPMO Approved by the Foundation for Cross -Connection Control and Hydraulic Research at the University of Southern California. Approval models QT, PC, NRS, OSY. UL Classified 21/2" and 3" (65 and 80mm) with OSY gate valves. 3/4" - 2" (20-50mm) without shutoff valves (-LF) (except LF009M3LF) MODEL DRAIN OUTLET DIMENSIONS for 909, 009 and 993 sizes A B in. mm in. mm in. mm lbs. kgs. 909AGA /4"-/i' 009, '/z 13 2% 60 3'/e 79 0.625 0.28 1/4" 009M2/M3 909AGC 1/411-1" 009/909, 1 25 3'/4 83 4% 124 1.5 0.68 1"-11/2" 009M2 909AGF 1'/4"-2" 009M1, 2 51 4% 111 61% 171 3.25 1.47 11/4"-3" 009/909, 2" 009M2 4"4"993 909AGK 4"-6" 909, 3 76 61% 162 9% 244 6.25 2.83 8"-10" 909M1 909AGM 8"-10" 909 4 102 7% 187 111/4 286 15.5 7.03 909ELA 1/4"—'/2" 009 1/4" 009M2/M3 - - - - - - - - 909ELC 1/4"-1" 009/909 - - 2% 60 2% 60 0.38 0.17 • 909ELF 11/4"-2" 009M1, - - 355% 92 3% 92 2 0.91 11/4"-2" 009/909, 2" 009M2 4"-" 993 • 909ELH 2'/2"-3" 009/909 - - - - - - - - Vertical Dimensions and Weight: 1/4" - 2" (8 - 50mm) LF009 LF009 1/4" — 2" Dimensions and Weight: 2'/2" and 3" (65 and 80mm) LF009 � U � Ni N L E ---------- M ---------- -------------------- A STRAINER SIZE DIMENSIONS i M N Nit in. mm in. mm in. mm in. mm lbs. kgs. 21/2 65 10 254 61/2 165 93/4 248 28 12.7 3 80 10'/a 257 7 178 10 254 34 15.4 tClearance for servicing C open 0 0 Uo 0 R Watts G-4000 Series QT — Ball Valves Capacity Performance as established by an independent testing laboratory. kPa psi %" (8mm) LF0090T 138 20 117 17 96 14 76 11 55 8 35 5 0 .25 .60 .75 1 1.17 gpm AP 0 .95 1.9 2.9 3.8 4.5 Ipm kPa psi 3/s" (10mm) LF009QT 138 20 117 17 96 14 76 11 55 8 35 5 0 .25 .50 .75 1 1.25 1.50 2.5 3.1 gpm AP 0 .95 1.9 2.9 3.8 4.8 5.7 9.4 11.8 Ipm kPa psi 207 30 165 24 124 18 83 12 (20mm) LF009M3QT 41 6 0 0 [111 1111111111 [111 11 11 FM 0 2 6 10 14 18 22 26 30 34 38 42 46 gpm AP 07.6 23 38 53 68 84 99 114 129 144 160175 Ipm 7.5 15 fps 2.3 4.6 mps 1- (25mm) LF009M20T kPa psi 207 30 172 25 138 20 103 15 69 10 35 5 00 0 5 10 20 30 40 50 60 70 80 gpm AP 0 19 38 76 114 152 190 228 266 304 Ipm 7.5 15 fps 2.3 4.6 mps INWATM A Watts Water Technologies Company `Typical maximum system flow rate (7.5 feet/sec., 2.3 meters/sec.) kPa psi 1'/a" (32mm) LF009M2QT 172 25 138 20 103 15 69 10 35 5 0 0 APO10 20 30 40 50 60 70 80 gpm 0 38 76 114 152 190 228 266 304 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps kPa psi 1'/z" (40mm) LF009M20T 207 30 172 25 138 20 103 15 69 10 35 5 0 0 0 10 20 30 40 50 60 70 80 90 100 110 120 gpm AP 0 38 76 114 152 190 228 266 304 342 380 418 456 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps kPa psi 2" (50mm) LF009M20T 207 30 172 25 138 20 103 15 69 10 35 5 0 0 �P 0 20 40 60 80 100 120 140 160 180 200 gpm 0 76 152 228 304 380 456 532 608 684 760 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps kPa psi 2'1" (65mm) LF009 172 25 138 20 103 15 69 10 35 5 0 0 0 25 50 75 100 125 150 175 200 225 250 gpm AP 0 05 10- 295 380 475 570 665 760 885 950 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps '/z" (15mm) LF0090T kPa psi 172 25 138 20 138 20 103 15 44 6910 103 15 35 5 69 10 0 AP 25 50 75 100 125 150 175 200 225 250 275 300 325 gpm 35 5 95 190 285 380 475 570 665 760 855 950 104511401235 Ipm 5 7.5 10 0 1 2.5 5 7.5 10 12.5 15 gpm 1.5 2.3 3.0 OP 0 3.8 9.5 19 28.5 38 47.5 57 Ipm 5 7.5 15 fps 1.5 2.3 4.6 mps kPa psi 207 30 165 24 124 18 83 12 (20mm) LF009M3QT 41 6 0 0 [111 1111111111 [111 11 11 FM 0 2 6 10 14 18 22 26 30 34 38 42 46 gpm AP 07.6 23 38 53 68 84 99 114 129 144 160175 Ipm 7.5 15 fps 2.3 4.6 mps 1- (25mm) LF009M20T kPa psi 207 30 172 25 138 20 103 15 69 10 35 5 00 0 5 10 20 30 40 50 60 70 80 gpm AP 0 19 38 76 114 152 190 228 266 304 Ipm 7.5 15 fps 2.3 4.6 mps INWATM A Watts Water Technologies Company `Typical maximum system flow rate (7.5 feet/sec., 2.3 meters/sec.) kPa psi 1'/a" (32mm) LF009M2QT 172 25 138 20 103 15 69 10 35 5 0 0 APO10 20 30 40 50 60 70 80 gpm 0 38 76 114 152 190 228 266 304 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps kPa psi 1'/z" (40mm) LF009M20T 207 30 172 25 138 20 103 15 69 10 35 5 0 0 0 10 20 30 40 50 60 70 80 90 100 110 120 gpm AP 0 38 76 114 152 190 228 266 304 342 380 418 456 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps kPa psi 2" (50mm) LF009M20T 207 30 172 25 138 20 103 15 69 10 35 5 0 0 �P 0 20 40 60 80 100 120 140 160 180 200 gpm 0 76 152 228 304 380 456 532 608 684 760 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps kPa psi 2'1" (65mm) LF009 172 25 138 20 103 15 69 10 35 5 0 0 0 25 50 75 100 125 150 175 200 225 250 gpm AP 0 05 10- 295 380 475 570 665 760 885 950 Ipm 5 7.5 10 15 fps 1.5 2.3 3.0 4.6 mps USA: Tel: (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com Canada: Tel: (905) 332-4090 • Fax: (905) 332-7068 • wwwmatts.ca ES-LF009 1406 © 2014 Watts 3" (80mm) LF009 kPa psi 172 25 138 20 103 15 44 6910 35 5 0 0 0 AP 25 50 75 100 125 150 175 200 225 250 275 300 325 gpm 0 95 190 285 380 475 570 665 760 855 950 104511401235 Ipm 5 7.5 10 fps 1.5 2.3 3.0 mps USA: Tel: (978) 688-1811 • Fax: (978) 794-1848 • www.watts.com Canada: Tel: (905) 332-4090 • Fax: (905) 332-7068 • wwwmatts.ca ES-LF009 1406 © 2014 Watts City of Tukwila Allan Ekberg, Mayor Department of Community Development . Jack Pace, Director June 17, 2016 ANDREW PAROLINE 3617 SW CHARLESTOWN ST SEATTLE, WA 98126 RE: Correction Letter # 1 to Revision #1 PLUMBING/GAS PIPING Permit Application Number PG16-0017 HABIT BURGER - 17025 SOUTHCENTER PKWY Dear ANDREW PAROLINE, This letter is to inform you of corrections that must be addressed before your development permit can be approved. All correction requests from each department must be addressed at the same time and reflected on your drawings. I have enclosed comments from the following departments: BUILDING DEPARTMENT: Allen Johannessen at 206-433-7163 if you have questions regarding these comments. (GENERAL NOTE) PLAN SUBMITTALS: (Min. size 1 Ix17 to maximum size of 2406; all sheets shall be the same size. New revised plan sheets shall be the same size sheets as those previously submitted.) (If applicable) "STAMP AND SIGNATURES" "Every page of a plan set must contain the seal/stamp, signature of the licensee(s) who prepared or who had direct supervision over the preparation of the work, and date of signature. Specifications that are prepared by or under the direct supervision of a licensee shall contain the seal/stamp, signature of the licensee and the date of signature. If the "specifications" prepared by a licensee are a portion of a bound specification document that contains specifications other than that of an engineering or land surveying nature, the licensee need only seal/stamp that portion or portions of the documents for which the licensee is responsible." It shall not be required to have each page of "specifications" (calculations) to be stamped and signed; Front page only will be sufficient. (WAC 196-23-010 & 196-23-020) (BUILDING REVIEW NOTES) 1. The revision shows a new sump pump installation where it shall be pumping to another sump pump located down line of this proposed pump installation. Provide sizing calculations with manufactures installation and specification for the new pump to include sizing specifications of the downstream pump to verify that the downstream pump shall be sufficient to handle the total demand of the new pump with any other fixtures connected to this drain system. PW DEPARTMENT: Joanna Spencer at 206-431-2440 if you have questions regarding these comments. • 1) Applicant or owner shall fill out attached King County Non -Residential Sewer Use Certification form. Please list all the new plumbing fixtures to be installed. Do not list the fixtures to be replaced in kind. Back page of your permit application is attached for reference. 2) Submit pump cut sheet and spec including pump maintenance requirements.. Please address the comments above in an itemized format with applicable revised plans, specifications, and/or other documentation. The City requires that two 2 sets of revised plan pages, specifications and/or other documentation be resubmitted with the appropriate revision block. In order to better expedite your resubmittal, a 'Revision Submittal Sheet' must accompany every resubmittal. I have enclosed one for your convenience. Corrections/revisions must be made in person and will not be accepted through the mail or by a messenger service. 6300 Southcenter Boulevard Suite #100 • Tukwila Washington 98188 • Phone 206-431-3670 • Fax 206-431-3665 If you have any questions, I can be reached at 206-431-3655. Sincerely, �* I �11 11 �i � �' Bill Rambo Permit Technician File No. PG 16-0017 6300 Southcenter Boulevard Suite #100 • Tukwila Washington 98188 • Phone 206-431-3670 e Fax 206-431-3665 FREDERICIIrJ. GOGLIA ARCHITECT, NCARB, ISP March 16, 2016 City of Tukwila Department of Community Development Attn: Mr. Bill Rambo 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 Ph: 206-431-3670 RE: Habit Burger Plumbing/Gas Piping Permit Application Number PG 16-0017 17025 Southcenter Pkwy Tukwila, WA ArcV Project: 150684 F4 16 - a n& -}--- This letter is in response to the comments dated March 8t", 2016. Please find below the comments and their respective responses. PW - PG DEPARTMENT: Joanna Spencer - 206-431-2440 1. PLUMBING FIXTURE SCHEDULE table on sheet P100 lists three backflows, BFP1, BFP2 and RPBFB. Please submit backflow cut sheets and circle devices to be installed. Please make sure these backflows are WA State Department of Health approved backflows. Response: Revise plumbing sheet P100 to comply with this comment. See attached cut sheets. 2. Show backflow location on the Water Diagram. Response: Revised plumbing sheet P400 to comply with this comment. 3. Per Mike Cusick, PE, Public Works Senior Water & Sewer Engineer items shown in red shall be tied to the grease waste line; see attached. Response: Revised plumbing sheets P200 and P400 to comply with this comment. If you have any questions, comments or need any additional information regarding this letter please contact Julia Test at our office at any time (817) 391-3970. Sincerely, )(ederick J. Goglil Architect, NCARB, ISP CC: File J:\Clients\Zales\ 140649\Docs CORRECTION LTR#� RECEIVED CITY OF i"t KWILA MAR 17 2016 PERMIT CENTER PC7 1 (04- D 0 11 1950 Craig Road Suite 300 • St. Louis, MO 63146-4106 e Phone (314) 415-2400 9 Fax (314) 415-2300 City of Tukwila Allan Ekberg, Mayor Department of Community Development Jack Pace, Director June 17, 2016 ANDREW PAROLINE 3617 SW CHARLESTOWN ST SEATTLE, WA 98126 RE: Correction Letter # 1 to Revision #1 PLUMBING/GAS PIPING Permit Application Number PG 16-0017 HABIT BURGER - 17025 SOUTHCENTER PKWY Dear ANDREW PAROLINE, This letter is to inform you of corrections that must be addressed before your development permit can be approved. All correction requests from each department must be addressed at the same time and reflected on your drawings. I have enclosed comments from the following departments: BUILDING DEPARTMENT: Allen Johannessen at 206-433-7163 if you have questions regarding these comments. (GENERAL NOTE) PLAN SUBMITTALS: (Min. size 11x17 to maximum size of 2406; all sheets shall be the same size. New revised plan sheets shall be the same size sheets as those previously submitted.) (If applicable) "STAMP AND SIGNATURES" "Every page of a plan set must contain the seal/stamp, signature of the licensee(s) who prepared or who had direct supervision over the preparation of the work, and date of signature. Specifications that are prepared by or under the direct supervision of a licensee shall contain the seal/stamp, signature of the licensee and the date of signature. If the "specifications" prepared by a licensee are a portion of a bound specification document that contains specifications other than that of an engineering or land surveying nature, the licensee need only seal/stamp that portion or portions of the documents for which the licensee is responsible." It shall not be required to have each page of "specifications" (calculations) to be stamped and signed; Front page only will be sufficient. (WAC 196-23-010 & 196-23-020) (BUILDING REVIEW NOTES) 1. The revision shows a new sump pump installation where it shall be pumping to another sump pump located down line of this proposed pump installation. Provide sizing calculations with manufactures installation and specification for the new pump to include sizing specifications of the downstream pump to verify that the downstream pump shall be sufficient to handle the total demand of the new pump with any other fixtures connected to this drain system. PW DEPARTMENT: Joanna Spencer at 206-431-2440 if you have questions regarding these comments. • 1) Applicant or owner shall fill out attached King County Non -Residential Sewer Use Certification form. Please list all the new plumbing fixtures to be installed. Do not list the fixtures to be replaced in kind. Back page of your permit application is attached for reference. 2) Submit pump cut sheet and spec including pump maintenance requirements.. Please address the comments above in an itemized format with applicable revised plans, specifications, and/or other documentation. The City requires that two 2 sets of revised plan pages, specifications and/or other documentation be resubmitted with the appropriate revision block. In order to better expedite your resubmittal, a'Revision Submittal Sheet' must accompany every resubmittal. I have enclosed one for your convenience. Corrections/revisions must be made in person and will not be accepted through the mail or by a messenger service. 6300 Southcenter Boulevard Suite #100 9 Tukwila Washington 98188 • Phone 206-431-3670 a Fax 206-431-3665 City of Tukwila Allan Ekberg, Mayor Department of Community Development Jack Pace, Director March 08, 2016 ANDREW PAROLINE 3617 SW CHARLESTOWN ST SEATTLE, WA 98126 RE: Correction Letter # l PLUMBING/GAS PIPING Permit Application Number PG16-0017 HABIT BURGER - 17025 SOUTHCENTER PKWY Dear ANDREW PAROLINE, This letter is to inform you of corrections that must be addressed before your development permit can be approved. All correction requests from each department must be addressed at the same time and reflected on your drawings. I have enclosed comments from the following departments: PW - PG DEPARTMENT: Joanna Spencer at 206-431-2440 if you have questions regarding these comments. • 1) PLUMBING FIXTURE SCHEDULE table on sheet P100 lists three backflows, BFP1, BFP2 and RPBFB. Please submit backflow cut sheets and circle devices to be installed. Please make sure these backflows are WA State Department of Health approved backflows. 2) Show backflow location on the Water Diagram. 3) Per Mike Cusick, PE, Public Works Senior Water & Sewer Engineer items shown in red shall be tied to the grease waste line; see attached. Please address the comments above in an itemized format with applicable revised plans, specifications, and/or other documentation. The City requires that two 2 sets of revised plan pages, specifications and/or other documentation be resubmitted with the appropriate revision block. In order to better expedite your resubmittal, a 'Revision Submittal Sheet' must accompany every resubmittal. I have enclosed one for your convenience. Corrections/revisions must be made in person and will not be accepted through the mail or by a messenger service. If you have any questions, I can be reached at (206)431-3655. Sincerely, Bill Rambo Permit Technician File No. PG 16-0017 6300 Southcenter Boulevard Suite #100 • Tukwila Washin,eton 98188 • Phone 206-431-3670 • Fax 206-431-3665 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Web site: http://www.TukwilaWA.p_ov REVISION SUBMITTAL Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: 3c� Plan Check/Permit Number: PG i OU ❑ Response to Incomplete Letter # RECEIVED Response to Correction Letter # /A, CITY OF TUKWILA 0 Revision #_ after Permit is Issued JUN 3 0 2016 ❑ Revision requested by a City Building Inspector or Plans Examiner ❑ Deferred Submittal # PERMIT CENTER Project Name: 6h; + �u _rG e ✓ Project Address: l"7 0 a S <10(- h &-411-(< ✓ L-1) � Contact Person: P�n(A jn (into_Phone Number: Summary of Revision: PI A m F ME Sheet Number(s): P 2a0 "Cloud" or highlight all areas of revision including date of revision Received at the City of Tukwila Permit Center by: Entered in TRAKiT on Q "-30 W.Termit CenterUemplatesTorms\Revision Submittal Form. doc Revised: August 2015 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Web site: http://ww,v.TukwilaAVA.gov REVISION SUBMITTAL Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: &- �`7-Plan Check/Permit Number: R6 //,0- w ❑ Response to Incomplete Letter # RECEIVED Response to Correction Letter # CITY OF TUKWILA Revision # J— after Permit is Issued JUN 2 -4 2016 ❑ Revision requested by a City Building Inspector or Plans Examiner ❑ Deferred Submittal # PERMIT CENTER Project Name: Project Addre: Contact Person: Summary of Revision: Phone Number: -ZL-J& �qj 7 '03V Sheet Number(s): "Cloud" or highlight all areas of revision including date of revision Received at the City of Tukwila Permit Center by: 0 Entered in TRAKiT on WAPermit CenterUemplatesTorms\Revision Submittal Form. doc Revised: August 2015 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Web site: http://www.Tukwi]aWA.gov REVISION SUBMITTAL Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: V Plan Check/Permit Number: F6 ❑ Response to Incomplete Letter # Response to Correction Letter # Revision # -A— after Permit is Issued ❑ Revision requested by a City Building Inspector or Plans Examiner ❑ Deferred Submittal # Project Name: Toe H -g pU i,q e -l- r, Project Address: Ccz) - e- 04 r e- re -(-7,' 1?07-5 .Soli to ce , 4e,- Pf rlcw Contact Person:__ PAio �i`o C Phone Number: Z06 719'=o3-39 Summary of Revision: U INS (4'n assoc( -fc / U�ovS� 50 � 1-h 1 t�, Dv C +0 �o � � � -�t� j ,`� fill ��,` � s�c�' our � P14� s fiv C��iu wt`fi1, & UP -J (f- l y Co J e , P 1-e - s -c Sze t-��. �� C loS-e.e/ 5, RECEIVED CITY OF TUKWILA PERMIT CENTER Sheet Number(s): Z U U "Cloud" or highlight all areas o) 7-10 , f L/U0 , F-1q0 revision including date of revision Received at the City of Tukwila Permit Center by:/� d] Entered in TRAKiT on V" , WAPermit CenterUemplatesTormsTevision Submittal Form.doc Revised: August 2015 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Web site: hiip://wA,,�Nr.Tukwi]aWA.gov REVISION SUBMITTAL Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: ' 7 (6 Plan Check/Permit Number: -Pq 1 G — UU ( -7 ❑ Response to Incomplete Letter # a Response to Correction Letter # ❑ Revision # after Permit is Issued ❑ Revision requested by a City Building Inspector or Plans Examiner ❑ Deferred Submittal # Project Name: %` -f- 9CJ roar 6-r 11 Project Address: C / 176 ZS Svvt�i Cel4e r P -2r jc r,J� Contact Person: llcl �� r0 ,l,le Phone Number: Z 0 6 719-0,53-7 Summary of Revision: See LA R Sheet Number(s): "Cloud" or highlight all areas of revision including data4iCzevision Received at the City of Tukwila Permit Center by: N— Entered in TRAKiT on W:Termit Centeffemplates\Forms\Revision Submittal Form. doc Revised: August 2015 PERMIT COORD COPS PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG16-0017 DATE: 06/24/16 PROJECT NAME: HABIT BURGER SITE ADDRESS: 17025 SOUTHCENTER PKWY Original Plan Submittal Revision # before Permit Issued X Response to Correction Letter # 1 X Revision # 1 after Permit Issued DEPARTMENTS: ,�? But ding Division Fire Prevention ❑ Planning Division ❑ Public Works Structural ❑ Permit Coordinator PRELIMINARY REVIEW: DATE: 06/28/16 Not Applicable ❑ Structural Review Required ❑ (no approval/review required) REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: DUE DATE: 07/26/16 Approved ❑ Approved with Conditions ❑f Corrections Required ❑ Denied ❑ (corrections entered in Reviews) (ie: Zoning Issues) Notation: REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: 12/18/2013 PERMIT COORD COPY PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG16-0017 DATE: 06/10/16 PROJECT NAME: HABIT BURGER SITE ADDRESS: 17025 SOUTHCENTER PKWY Original Plan Submittal Response to Correction Letter # Revision # before Permit Issued X Revision # 1 after Permit Issued DEPARTMENTS: Building Division Fire Prevention ❑ Planning Division ❑ Ji s tory 6.1 (0 Public Works Structural ❑ Permit Coordinator ❑ PRELIMINARY REVIEW: DATE: 06/14/16 Not Applicable ❑ Structural Review Required ❑ (no approval/review required) REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: DUE DATE: 07/12/16 Approved ❑ Approved with Conditions ❑ Corrections Required ❑ Denied ❑ (corrections entered in Reviews) (ie: Zoning Issues) Notation: REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: & Departments issued corrections: Bldg--- Fire ❑ Ping ❑ PW'�J— Staff Initials: IV 12/18/2013 PERMIT COORD COPY PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG16-0017 DATE: 03/17/16 PROJECT NAME: HABIT BURGER SITE ADDRESS: 17025 SOUTHCENTER PKWY Original Plan Submittal Revision # before Permit Issued X Response to Correction Letter # 1 Revision # after Permit Issued DEPARTMENTS: Building Division ❑ �)s 4wc Public Works PRELIMINARY REVIEW: Not Applicable ❑ (no approval/review required) REVIEWER'S INITIALS: APPROVALS OR CORRECTIONS: Approved ❑ Corrections Required ❑ (corrections entered in Reviews) Notation: REVIEWER'S INITIALS: Fire Prevention ❑ Planning Division ❑ Structural ❑ Permit Coordinator a DATE: 03/22/16 Structural Review Required ❑ DATE: DUE DATE: 04/19/16 Approved with Conditions Denied ❑ (ie: Zoning Issues) DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: 12/18/2013 PERMIT COORD COPY PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG16-0017 DATE: 02/17/16 PROJECT NAME: HABIT BURGER SITE ADDRESS: 17025 SOUTHCENTER PKWY X Original Plan Submittal Revision # before Permit Issued Response to Correction Letter # Revision # after Permit Issued DEPARTMENTS: Building Division Fire Prevention ❑ Planning Division ❑ uJ Cir � Public Works Structural ❑ Permit Coordinator ❑ PRELIMINARY REVIEW: DATE: 02/18/16 Not Applicable ❑ (no approval/review required) REVIEWER'S INITIALS: APPROVALS OR CORRECTIONS: Structural Review Required ❑ DATE: DUE DATE: 03/17/16 Approved ❑ Approved with Conditions ❑ Corrections Required �— Denied ❑ (corrections entered in Reviews) (ie: Zoning Issues) Notation: REVIEWER'S INITIALS: DATE: Permit Center Use Only Q� I CORRECTION LETTER MAILED: v� t Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW [ Staff Initials: 12/18/2013 PROJECT NAME: ` "10 e r PERMIT NO: -GCS SITE ADDRESS: S .56g I ORIGINAL ISSUE DATE: REVISION LOG REVISION DATE RECEIVED STAFF ISSUED DATE STAFF NO. INITIALS INITIALS Summary of Revision: hew s �� o-%) vrNo i v`d+in_a av44� mfj I P Received REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Summary of Revision: Received by: (please print) REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Summary of Revision: Received by: (please print) REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Summary of Revision: Received by: (please print) REVISION NO. DATE RECEIVED STAFF INITIALS ISSUED DATE STAFF INITIALS Summary of Revision: Received by: (please print) REVISION NO. DATE RECEIVED STAFF ISSUED DATE INITIALS STAFF INITIALS Summary of Revision: Received by: (please mint) TUMYA PLUMBING CONTRACTOR, LLC OnWashington State Department of abor & 'Industries Page 1 of 2 Home Espahol coIltaet A-7. Index Help my I.,&l Safety & Health Claims & Insurance Workplace Rights Trades & Licensing TUMYA PLUMBING CONTRACTOR, LLC Owner or tradesperson Principals GOULD, DEBBIE LYNNE, PARTNER/MEMBER Gould, Bryan Michael, PARTNER/MEMBER Doing business as TUMYA PLUMBING CONTRACTOR, LLC WA UBI No. 603 185 567 License 5817 73rd Lane SW OLYMPIA, WA 98512 360-878-0601 THURSTON County Business type Limited Liability Company Verify the contractor's active registration / license / certification (depending on trade) and any past violations. Construction Contractor Active. Meets current requirements. License specialties $1,000,000.00 PLUMBING License no. TUMYAPC880JR Effective date Effective — expiration 02/03/2015 04119/2012— 04/19/2018 Expiration date Bond ................ 02/03/2017 Wesco Insurance Co $6,000.00 Bond account no. 46wb045862 Received by L&I Effective date 04/08/2014 04/19/2014 Expiration date Until Canceled Bond history Insurance Security National Insurance $1,000,000.00 Policy no. NA107513601 Received by L&I Effective date 01/25/2016 02/03/2015 Expiration date 02/03/2017 Insurance history Savings N ....._..._.._.. _... o savings accounts during the previous 6 year period. Lawsuits against the bond or savings No lawsuits against the bond'6 rsavings accounts during the previous 6 year period. L&I Tax debts bUS-OqqO77 https://secure.lni.wa.gov/verify/Detail.aspx?UBI=603185567&LIC=TUMYAPC880JR&SAW= 4/26/2016 TO EXISTING LIFT STATION I / EX 4 ELEVATION: 2: BELOW UNDEF OF FLOOR AE i �•�� TO Nil W �fl scar? va - r -W A �1� , 1� r e ' k i4wl � 111 will WiR GRINDER PUMP PACKAGES: PUMP WITH FLOAT PACKAGE - #DUPRGSKTN4 EXISTING CLEANOUT 36" DIAMETER x 48" DEEP BASIN PACKAGE - #D4NGRD48 ELEVATION: 19" BELOW UNDERSIDE OF FLOOR ABOVE ALARM PANEL - CENTRIPRO MODEL A6-2012 PROVIDE WITH NEMA 3R ENCLOSURE, ALARM CIRCUITS: 1) HIGH OR LOW LEVEL ALARM CIRCUIT. 2) GUARANTEED PUMP SUBMERGENCE CIRCUIT WITH LOW LEVEL ALARM (OVERRIDES MANUAL AND AUTOMATIC OPERATION OF PUMPS). 3) EXTRA SET OF DRY CONTACTS (USED FOR SIGNAL REMOTE ALARM DEVICE). ALARM DEVICE, HORN (101 db ® 10 ft.), NEMA 3R. REMOTE ALARM LIGHT IN SEPARATE NEMA1 ENCLOSURE (REQUIRES 115V SUPPLY). CONVIENCE OUTLET (115V GFI) WITH CIRCUIT BREAKER PROTECTION, MOUNTED INTERNALLY. GREASE TRAP CALCULATIONS 3 COMPARTMENT SINK (20) S.S. SANITARY SEWER LINE 18 * 24 * 14 = 6048 GREASE WASTE LINE T.M.V. THERMOSTATIC MIXING VALVE 6048 * 3 = 18144 VENT LINE T.P.R.V. TEMP. PRESSURE RELIEF VALVE 18144 / 231 = 78.5455 GAS LINE +P.O.C. POINT OF CONNECTION 78.545 * 75% = 58.9091 GA L. COLD WATER LINE B.F.P. BACK FLOW PREVENTER MOP BASIN (GC -6) HOT WATER LINE 24 * 24 * 10 = 5760 TEMPERED WATER LINE LAV. LAVATORY 5760 / 231 = 24.9351 FILTERED WATER LINE UR. URINAL SHUT-OFF VALVE 24.935 * 75% = 18.7013 GAL. WATER CLOSET IJACKFLOW PREVENTER 2HANDSINKS121) GLASS RACK 12 * 10 * 5 = 600 A.F.F. ABOVE FINISHED FLOOR 600 / 231 = 2.5974 CAST IRON BELOW FINISHED FLOOR 2.5974 * 75% = 1.94805 GAL. COLD WATER M WATER METER H.W. HOT WATER PREP SINK (22) WATER HEATER 18 * 20 * 14 = 5040 E.C.O. EXTERIOR CLEAN-OUT 5040 / 231 = 21.8182 FILTER WATER F.C.O. FLOOR CLEAN-OUT 21.818 * 75% = 16.3636 GAL. FLOOR SINK W.C.O. WALL CLEAN-OUT F.D. TOTAL CAPACITY M.S. MOP SINK 58.909 + 18701 + 0 + 16.3636364F -=T93.97 GAL. F.F.D. FUNNEL FLOOR DRAIN F.E.S. 93.974 GPM FOR 1 MINUTES K.F.D. 'rITCHEN FLOOR DRAIN 46.987 GPM FOR 2 MINUTE HAND SINK R.F.D. REVISIONS changes shall be --made to the-, scope of 4vork without prior approval of Tuktivila Building Division. Revision, will require a new plan submittal i may include additional plan review fees. I 1. REFER TO RISER DIAGRAM ON SHEET P400 FOR PIPE SIZES. 2. REFER TO PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR KEYED NOTES O AND O . 3. INDIRECT WASTE PIPES EXCEEDING 5 FEET, BUT LESS THAN 15 FEET IN LENGTH SHALL BE DIRECTLY TRAPPED, BUT SUCH TRAPS NEED NOT BE VENTED PER SECTION 803.1 OF THE 2013 CALIFORNIA PLUMBING CODE, �veov kn final insye�m�� h�l� Vol pumps @ll�acilry {v a%w �uu -Wt, dowgsf�ram Puy'" KAS & cagaei�ry� LU luaa.5- Ing CopyPermit Ift Flan review appfoval is subject to errom and omissions. Ap rovai of construction documents dogs not auIlhodza the vic iaJon of arty ndoptod coda or ordinance. REccipt of approvod Flaid Cand co aitions is acknowledged: r3y: Date. 71YY� M./ ■ .I.rl �lll,��"�A� City of Ttakw a BUILDING DIVISION LINE TYPES SS SANITARY PIPING GW GREASE WASTE PIPING CONDENSATE PIPING VENT PIPING O NEW HAND SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW PREP SINK. ROUTE 1 1/2" COPPER -WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW ICE MAKER WITH BIN. ROUTE INDIRECT'. WASTE TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW URINAL. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW MOP SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. ONEW 3 COMP SINK. ROUTE 1 1/2", COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW CARBONATOR/SODA RACK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. n8 NEW SODA MACHINE W/ICE MAKER ABOVE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATIO ECEIVED PLUMBING SYMBOLS S.S. SANITARY SEWER LINE T.P. TRAP PRIMER G.W. GREASE WASTE LINE T.M.V. THERMOSTATIC MIXING VALVE V VENT LINE T.P.R.V. TEMP. PRESSURE RELIEF VALVE LAVATORY. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. GAS LINE +P.O.C. POINT OF CONNECTION FLOOR DRAIN. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. COLD WATER LINE B.F.P. BACK FLOW PREVENTER HOT WATER LINE G.I./T. GREASE INTERCEPTOR/TRAP TEMPERED WATER LINE LAV. LAVATORY FILTERED WATER LINE UR. URINAL SHUT-OFF VALVE W.C. WATER CLOSET IJACKFLOW PREVENTER G.R. GLASS RACK V.T.R. VENT THRU ROOF A.F.F. ABOVE FINISHED FLOOR C.I. CAST IRON BELOW FINISHED FLOOR C.W. COLD WATER M WATER METER H.W. HOT WATER .H. WATER HEATER T.W. TEMPERED WATER E.C.O. EXTERIOR CLEAN-OUT F.W. FILTER WATER F.C.O. FLOOR CLEAN-OUT F.S. FLOOR SINK W.C.O. WALL CLEAN-OUT F.D. FLOOR DRAIN M.S. MOP SINK H.D. HUB DRAIN S.S. SCULLERY SINK F.F.D. FUNNEL FLOOR DRAIN F.E.S. FABRICATED ECONOMY SINK K.F.D. 'rITCHEN FLOOR DRAIN H.S. HAND SINK R.F.D. RESTROOM FLOOR DRAIN U.B.S. UNDER BAR SINK E.M. ELECTRICAL METER U.B.H.S. UNDER BAR HAND SINK G.M. GAS METER I.C.C. ICE CREAM CABINET �veov kn final insye�m�� h�l� Vol pumps @ll�acilry {v a%w �uu -Wt, dowgsf�ram Puy'" KAS & cagaei�ry� LU luaa.5- Ing CopyPermit Ift Flan review appfoval is subject to errom and omissions. Ap rovai of construction documents dogs not auIlhodza the vic iaJon of arty ndoptod coda or ordinance. REccipt of approvod Flaid Cand co aitions is acknowledged: r3y: Date. 71YY� M./ ■ .I.rl �lll,��"�A� City of Ttakw a BUILDING DIVISION LINE TYPES SS SANITARY PIPING GW GREASE WASTE PIPING CONDENSATE PIPING VENT PIPING O NEW HAND SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW PREP SINK. ROUTE 1 1/2" COPPER -WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW ICE MAKER WITH BIN. ROUTE INDIRECT'. WASTE TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW URINAL. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW MOP SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. ONEW 3 COMP SINK. ROUTE 1 1/2", COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW CARBONATOR/SODA RACK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. n8 NEW SODA MACHINE W/ICE MAKER ABOVE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATIO ECEIVED 13 1 1/4" CONDENSATE DRAIN FROM RTU -1, RTU -2 AND MAU-1 DOWN IN WALL AND TERMINATE INTO MOP BASIN WITH CODE APPROVED AIR GAP. 14 NEW FLOOR SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 15 NEW WALL CLEAN-OUT. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 16 PROVIDE 4" CONDUIT FOR SODA LINES IN WALL. 17 4" GREASE WASTE TO GALLON GREASE INTERCEPTOR, FURNISHED AND INSTALLED BY LANDLORD. SEE PROJECT CIVIL DRAWINGS FOR ADDITIONAL DETAILS AND LOCATION. r 18 EXTEND AND CONNECT NEW 1 1/4 FORCED MAIN FROM GRINDER PUMP TO EXISTING SANITARY SEWER PIPING.Sp VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FIELD....W W _...._z 1 L_....... 1 g NEW 3 VENT UP AND CONNECT TO LANDLORD CAPPED 4 VENT THRU ROOF. CONTRACTOR TO PROVIDE VENT PIPING ��[,--�" •; �•-.�.-.-..•....,. EXTENSIONS TO ENSURE VENT PIPING IN HIGHER THAN PARAPET. ENSURE VENT THRU ROOF IS AT LEAST 10'-0" I=! O AWAY FROM ALL OUTSIDE AIR INTAKES. FIELD VERIFY LOCATION. ~ -- Wi � ,..:,. 10 O20 ROUTE CONDENSATE DRAIN FROM COOLER AND FREEZER TO FLOOR SINK. SEE RISER DIAGRAM FOR ADDITIONAL INFORMATION. C-) C5: I .� 21 NEW GAS WATER HEATER INSTALLED ON CONCRETE CURB. SEE ARCHITECTURAL DRAWINGS FOR CURB DETAILS. SEE W s =x PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL WATER HEATER INFORMATION. _........ ................ .............._......,........ 22 WATER FILTER SYSTEM. REFER TO EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. 23 ROUTE SODA LINES WITHOUT CONDUIT FROM BAG -N -BOX OVERHEAD AND DROP IN .NEARBY WALL WITH CONDUIT AT ! SODA DISPENSER. COORDINATE DROP IN FIELD WITH SODA VENDOR. FIELD VERIFY LOCATION. i z 1 101- 1 lL1 1/2" DRAIN UP THRU ROOF TO MAU-1. COORDINATE LOCATION THE MECHANICAL CONTRACTOR.., I � I ojM:E iCO 25 1/2"CW FROM TRAP PRIMER. SEE WATER RISER DIAGRAM AND PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL 1C) ! Q INFORMATION. Ic `= C_1t=�� I , :; f fl@ 26 TRAPZILLA MODEL #TZ -1826 100 GPM INTERIOR GREASE INTERCEPTOR. MOUNT 18 INCHES BELOW SUBFLOOR WITH n. o. ; I W .......A... -..... -..r.....• rr.. ........'........ ..... COLLAR EXTENSIONS TO SUBFLOOR. USE TRAPZILLA COVER MODEL #FTCA-22. SEE SHEET P420 FOR DETAILS. SEE I 3 STRUCTURAL DRAWINGS FOR MOUNTING FRAME. �� ^� ,Q 27 Cn ALL PIPING UNDER SUBFLOOR TO BE HUNG FROM SUBFLOOR IN CRAWLSPACE. o o o W 28 DROP SANITARY PIPING DOWN TO AVOID STRUCTURAL BEAM. FIELD VERIFY LOCATION. SLOPE PIPE AT 1/8" PER I TO CONNECT WITH EXISTING SANITARY MAIN. SEE RISER DIAGRAM ON SHEET P400 FOR ADDITIONAL INFORMATION. 29 DUPLEX SEWAGE GRINDER PUMPS AND BASIN IN CRAWL SPACE. SEWAGE EJECTOR TO BE GOULD MODEL RGS2012, 41 o GPM ® 30' TDH, 1 1/4- NPT DISCHARGE, 2HP, 208/23OV/1 PH, 3450 RPM, PROVIDE 36" DIAMETER SUMP BASIN x U N 48" DEEP AND ASSOCIATED CHECK VALVES. PROVIDE POLY LIFT ROPE FOR PULLING OF SUMP PUMPS. PROVIDE O CENTRIPRO CONTROL PANEL MODEL A6-2012 LOCATED WITHIN SIGHT IN CRAWL. LOW VOLTAGE AUXILIARY ALARM IN Y �— SPACE LOCATION PER HABIT BURGER. ACCESS TO PUMP AND PIT THROUGH "JOINT CRAWLSPACE ACCESS PANEL". �I _ N 30 1 1/4" SUMP DISCHARGE. INSTALL TO UNDERSIDE OF STRUCTURAL BEAMS. CITY OF TUKWILA gU NEW ICE TEA BREWER. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 10 NEW WATER CLOSET. REFER TO PLUMBING FIXTURE SCHEDULE FOR INFORMATION. JUN 10 2016 11 NEW LAVATORY. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. PERMIT CENTER 12 NEW FLOOR DRAIN. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 13 1 1/4" CONDENSATE DRAIN FROM RTU -1, RTU -2 AND MAU-1 DOWN IN WALL AND TERMINATE INTO MOP BASIN WITH CODE APPROVED AIR GAP. 14 NEW FLOOR SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 15 NEW WALL CLEAN-OUT. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 16 PROVIDE 4" CONDUIT FOR SODA LINES IN WALL. 17 4" GREASE WASTE TO GALLON GREASE INTERCEPTOR, FURNISHED AND INSTALLED BY LANDLORD. SEE PROJECT CIVIL DRAWINGS FOR ADDITIONAL DETAILS AND LOCATION. r 18 EXTEND AND CONNECT NEW 1 1/4 FORCED MAIN FROM GRINDER PUMP TO EXISTING SANITARY SEWER PIPING.Sp VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FIELD....W W _...._z 1 L_....... 1 g NEW 3 VENT UP AND CONNECT TO LANDLORD CAPPED 4 VENT THRU ROOF. CONTRACTOR TO PROVIDE VENT PIPING ��[,--�" •; �•-.�.-.-..•....,. EXTENSIONS TO ENSURE VENT PIPING IN HIGHER THAN PARAPET. ENSURE VENT THRU ROOF IS AT LEAST 10'-0" I=! O AWAY FROM ALL OUTSIDE AIR INTAKES. FIELD VERIFY LOCATION. ~ -- Wi � ,..:,. 10 O20 ROUTE CONDENSATE DRAIN FROM COOLER AND FREEZER TO FLOOR SINK. SEE RISER DIAGRAM FOR ADDITIONAL INFORMATION. C-) C5: I .� 21 NEW GAS WATER HEATER INSTALLED ON CONCRETE CURB. SEE ARCHITECTURAL DRAWINGS FOR CURB DETAILS. SEE W s =x PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL WATER HEATER INFORMATION. _........ ................ .............._......,........ 22 WATER FILTER SYSTEM. REFER TO EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. 23 ROUTE SODA LINES WITHOUT CONDUIT FROM BAG -N -BOX OVERHEAD AND DROP IN .NEARBY WALL WITH CONDUIT AT ! SODA DISPENSER. COORDINATE DROP IN FIELD WITH SODA VENDOR. FIELD VERIFY LOCATION. i z 1 101- 1 lL1 1/2" DRAIN UP THRU ROOF TO MAU-1. COORDINATE LOCATION THE MECHANICAL CONTRACTOR.., I � I ojM:E iCO 25 1/2"CW FROM TRAP PRIMER. SEE WATER RISER DIAGRAM AND PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL 1C) ! Q INFORMATION. Ic `= C_1t=�� I , :; f fl@ 26 TRAPZILLA MODEL #TZ -1826 100 GPM INTERIOR GREASE INTERCEPTOR. MOUNT 18 INCHES BELOW SUBFLOOR WITH n. o. ; I W .......A... -..... -..r.....• rr.. ........'........ ..... COLLAR EXTENSIONS TO SUBFLOOR. USE TRAPZILLA COVER MODEL #FTCA-22. SEE SHEET P420 FOR DETAILS. SEE I 3 STRUCTURAL DRAWINGS FOR MOUNTING FRAME. �� ^� ,Q 27 Cn ALL PIPING UNDER SUBFLOOR TO BE HUNG FROM SUBFLOOR IN CRAWLSPACE. o o o W 28 DROP SANITARY PIPING DOWN TO AVOID STRUCTURAL BEAM. FIELD VERIFY LOCATION. SLOPE PIPE AT 1/8" PER I TO CONNECT WITH EXISTING SANITARY MAIN. SEE RISER DIAGRAM ON SHEET P400 FOR ADDITIONAL INFORMATION. 29 DUPLEX SEWAGE GRINDER PUMPS AND BASIN IN CRAWL SPACE. SEWAGE EJECTOR TO BE GOULD MODEL RGS2012, 41 o GPM ® 30' TDH, 1 1/4- NPT DISCHARGE, 2HP, 208/23OV/1 PH, 3450 RPM, PROVIDE 36" DIAMETER SUMP BASIN x U N 48" DEEP AND ASSOCIATED CHECK VALVES. PROVIDE POLY LIFT ROPE FOR PULLING OF SUMP PUMPS. PROVIDE O CENTRIPRO CONTROL PANEL MODEL A6-2012 LOCATED WITHIN SIGHT IN CRAWL. LOW VOLTAGE AUXILIARY ALARM IN Y �— SPACE LOCATION PER HABIT BURGER. ACCESS TO PUMP AND PIT THROUGH "JOINT CRAWLSPACE ACCESS PANEL". �I _ N 30 1 1/4" SUMP DISCHARGE. INSTALL TO UNDERSIDE OF STRUCTURAL BEAMS. ci illy, W14'rmill, EIR11,=1e;i TO EXISTING LIFT STATION EX 4 ELEVATION: 2! BELOW UNDEf OF FLOOR AE EXISTING CLEANO ELEVATION: 19" BELOW UNDERSIDE OF FLOOR ABOVE ,m 1 1, 1 ,, 1 `k.'' r _ � 1 i s �1 PPMR11 FLOW CALCULATIONS: GREASE INTERCEPTOR: WATER CLOSET (3 ® 1.28): LAVATORY (2 Q .5 GPM): URINAL (1 CSD .125 GPM): 50 GPM 3.84 GPM 1.0 GPM 0.5 GPM TOTAL GPM; 56.34 GPM TOTAL HEAD: 30' LENGTH TO CONNECT TO SEWER: 85' PUMP WITH FLOAT PACKAGE - #DUPRGSKTN4 36" DIAMETER K 48" DEEP BASIN PACKAGE - #D4NGRD48 ALARM PANEL - CENTRIPRO MODEL A6-2012 PROVIDE WITH NEMA 3R ENCLOSURE, ALARM CIRCUITS: 1) HIGH OR LOW LEVEL ALARM CIRCUIT. 2) GUARANTEED PUMP SUBMERGENCE CIRCUIT WITH LOW LEVEL ALARM (OVERRIDES MANUAL AND AUTOMATIC OPERATION OF PUMPS). 3) EXTRA SET OF DRY CONTACTS (USED FOR SIGNAL REMOTE ALARM DEVICE). ALARM DEVICE, HORN (101 db ® 10 ft.), NEMA 3R. REMOTE ALARM LIGHT IN SEPARATE NEMA1 ENCLOSURE (REQUIRES 115V SUPPLY). CONVIENCE OUTLET (115V GFI) WITH CIRCUIT BREAKER PROTECTION, MOUNTED INTERNALLY. GREASE TRAP CALCULATIONS PLUMENING SYMBOLS 3 COMPARTMENT SINK (20) SANITARY SEWER LINE T.P. TRAP PRIMER 18 * 24 * 14 = 6048 REVS .CODE C AN JUL city BUILDI -------V------- 6048 * 3 = 18144 T.P.R.V. 18144 / 231 = 78.5455 - - - - - - - - 78.545 * 75% = 58.9091 GAL. *P.O.C. MOP BASIN (CC -6) 24 * 24 * 10 = 5760 COLD WATER LINE 5760 / 231 = 24.9351 BACK FLOW PREVENTER 24.9351*1 75% = 18.7013 GAL. HOT WATER LINE 2 HAND SINKS(21) 12 * 10 * 5 = 600 - - - - - 600 / 231 = 2.5974 LAV. 2.5974 * 75% = 1.94805 GAL. - • - • - • - - - FILTERED WATER LINE PREP SINK (22) 18 * 14 = 5040 5040 / 21.8182 J7516.3636 W.C. 21.818 * GAL. BACKFLOW PREVENTER G.R. GLASS RACK TOTAL CA PACITY VENT THRU ROOF A.F.F. ABOVE FINISHED FLOOR 58.909 + 13.701 + 0 1 + 116.3636364 11 93.97 GAL. C.W. COLD WATER I M I WATER METER 93.974 GPMFOR 1 MINUTES HOT WATER W.Tr WATER HEATER 46.987 GPM FOR 2 MINUTE TEMPERED WATER E.C.O. EXTERIOR CLEAN-OUT WED FOR JMPLIANCE ROVED 0 7 BIB )f Tukwila IG DIVISION CORRECTION LTR# NOTE: 1. REFER TO RISER DIAGRAM ON SHEET P400 FOR PIPE SIZES. 2. REFER TO PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR KEYED NOTES O AND 0. 3. INDIRECT WASTE PIPES EXCEEDING 5 FEET, BUT LESS THAN 15 FEET IN LENGTH SHALL BE DIRECTLY TRAPPED, BUT SUCH TRAPS NEED NOT BE VENTED PER SECTION 803.1 OF THE 2013 CALIFORNIA PLUMBING CODE, UNE TYPES SS SANITARY PIPING GW GREASE WASTE PIPING - CD - CD CD — CD - CONDENSATE PIPING --------------------- VENT PIPING -7.,1 z i i c i -t,,- +1 O NEW HAND SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O2 NEW PREP SINK. ROUTE 1 1/2" COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. �3 NEW ICE MAKER WITH BIN. ROUTE INDIRECT WASTE TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 4O NEW URINAL. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW MOP SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. ONEW 3 COMP SINK. ROUTE 1 1/2" COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW CARBONATOR/SODA RACK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. U8 PLUMENING SYMBOLS S.S. SANITARY SEWER LINE T.P. TRAP PRIMER G.W GREASE WASTE LINE T.M.V. THERMOSTATIC MIXING VALVE -------V------- VENT LINE T.P.R.V. TEMP. PRESSURE RELIEF VALVE - - - - - - - - GAS LINE *P.O.C. POINT OF CONNECTION - - COLD WATER LINE B.F.P. BACK FLOW PREVENTER — - - - - — HOT WATER LINE G.I./T. CREASE INTERCEPTOR/TRAP - - - - - TEMPERED WATER LINE LAV. LAVATORY - • - • - • - - - FILTERED WATER LINE UR. URINAL SHUT-OFF VALVE W.C. WATER CLOSET BACKFLOW PREVENTER G.R. GLASS RACK V.T.R. VENT THRU ROOF A.F.F. ABOVE FINISHED FLOOR C.I. CAST IRON QU. BELOW FINISHED FLOOR C.W. COLD WATER I M I WATER METER H.W. HOT WATER W.Tr WATER HEATER T.W. TEMPERED WATER E.C.O. EXTERIOR CLEAN-OUT F.W. FILTER WATER F.C.O. FLOOR CLEAN-OUT F.S. FLOOR SINK W.C.O. WALL CLEAN-OUT F.D. FLOOR DRAIN M.S. MOP SINK H.D. HUB DRAIN S.S. SCULLERY SINK F.F.D. FUNNEL FLOOR DRAIN F.E.S. FABRICATED ECONOMY SINK K.F.D. KITCHEN FLOOR DRAIN H.S. HAND SINK R.F.D. RESTROOM FLOOR DRAIN U.B.S. UNDER BAR SINK E.M. ELECTRICAL METER U.B.H.S. UNDER BAR HAND SINK G.M. GAS METER I.C.C. ICE CREAM CABINET UNE TYPES SS SANITARY PIPING GW GREASE WASTE PIPING - CD - CD CD — CD - CONDENSATE PIPING --------------------- VENT PIPING -7.,1 z i i c i -t,,- +1 O NEW HAND SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O2 NEW PREP SINK. ROUTE 1 1/2" COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. �3 NEW ICE MAKER WITH BIN. ROUTE INDIRECT WASTE TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 4O NEW URINAL. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW MOP SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. ONEW 3 COMP SINK. ROUTE 1 1/2" COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW CARBONATOR/SODA RACK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. U8 NEW SODA MACHINE W/ICE MAKER ABOVE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. RECEIVED O NEW ICE TEA BREWER. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. CITY OF TUKWILA 10 NEW WATER CLOSET. REFER TO PLUMBING FIXTURE SCHEDULE FOR INFORMATION. JUN 30 2016 11 NEW LAVATORY. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. PERMIT CENTERNEW 12 FLOOR DRAIN. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 13 1 1/4" CONDENSATE DRAIN FROM RTU -1, RTU -2 AND MAU-1 DOWN IN WALL AND TERMINATE INTO MOP BASIN WITH CODE APPROVED AIR GAP. 14 NEW FLOOR SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 15 NEW WALL CLEAN-OUT. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 16 PROVIDE 4" CONDUIT FOR SODA LINES IN WALL. 17 4" GREASE WASTE TO GALLON GREASE INTERCEPTOR, FURNISHED AND INSTALLED BY LANDLORD. SEE PROJECT CIVIL DRAWINGS FOR ADDITIONAL DETAILS AND LOCATION. 18 EXTEND AND CONNECT NEW 1 1/4" FORCED MAIN FROM GRINDER PUMP TO EXISTING SANITARY SEWER PIPING. VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FIELD. 19 NEW 3" VENT UP AND CONNECT TO LANDLORD CAPPED 4" VENT THRU ROOF. CONTRACTOR TO PROVIDE VENT PIPING EXTENSIONS TO ENSURE VENT PIPING IN HIGHER THAN PARAPET. ENSURE VENT THRU ROOF IS AT LEAST 10'-0" AWAY FROM ALL OUTSIDE AIR INTAKES. FIELD VERIFY LOCATION. 20 ROUTE CONDENSATE DRAIN FROM COOLER AND FREEZER TO FLOOR SINK. SEE RISER DIAGRAM FOR ADDITIONAL INFORMATION. 21 NEW GAS WATER HEATER INSTALLED ON CONCRETE CURB. SEE ARCHITECTURAL DRAWINGS FOR CURB DETAILS. SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL WATER HEATER INFORMATION. 22 WATER FILTER SYSTEM. REFER TO EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. 23 ROUTE SODA LINES WITHOUT CONDUIT FROM BAG -N -BOX OVERHEAD AND DROP IN NEARBY WALL WITH CONDUIT AT SODA DISPENSER. COORDINATE DROP IN FIELD WITH SODA VENDOR. FIELD VERIFY LOCATION. 24 1 1/2" DRAIN UP THRU ROOF TO MAU-1. COORDINATE LOCATION THE MECHANICAL CONTRACTOR. 25 1 /2"CW FROM TRAP PRIMER. SEE WATER RISER DIAGRAM AND PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. 26 TRAPZILLA MODEL #17-1826 100 GPM INTERIOR GREASE INTERCEPTOR. MOUNT 18 INCHES BELOW SUBFLOOR WITH COLLAR EXTENSIONS TO SUBFLOOR. USE TRAPZILLA COVER MODEL #FTCA-22. SEE SHEET P420 FOR DETAILS. SEE STRUCTURAL DRAWINGS FOR MOUNTING FRAME. 27 ALL PIPING UNDER SUBFLOOR TO BE HUNG FROM SUBFLOOR IN CRAWLSPACE. 28 DROP SANITARY PIPING DOWN TO AVOID STRUCTURAL BEAM. FIELD VERIFY LOCATION. SLOPE PIPE AT 1/8- PER FOOT TO CONNECT WITH EXISTING SANITARY MAIN. SEE RISER DIAGRAM ON SHEET P400 FOR ADDITIONAL INFORMATION. 29 DUPLEX SEWAGE GRINDER PUMPS AND BASIN IN CRAWL SPACE. SEWAGE EJECTOR TO BE GOULD MODEL RGS2012, 41 GPM ® 30' TDH, 1 1/4- NPT DISCHARGE, 2HP, 208/23CV/1PH, 3450 RPM, PROVIDE 36- DIAMETER SUMP BASIN x 48" DEEP AND ASSOCIATED CHECK VALVES. PROVIDE POLY LIFT ROPE FOR PULLING OF SUMP PUMPS. PROVIDE CENTRIPRO CONTROL PANEL MODEL A6-2012 LOCATED WITHIN SIGHT IN CRAWL. LOW VOLTAGE AUXILIARY ALARM IN SPACE LOCATION PER HABIT BURGER. ACCESS TO PUMP AND PIT THROUGH "JOINT CRAWLSPACE ACCESS PANEL". 30 1 1/4" SUMP DISCHARGE. INSTALL TO UNDERSIDE OF STRUCTURAL BEAMS. �C =1=1=1= x � �I� U C 3 i i � Q i Zj C)I � I (' W cn ��Nol ....... Q. CL 12: m i,.,.. W 3 - ��., g3 ......�...1ry....., �..... �...�. ! co CO i. Q 7z N?O N I fn M?co co W t o C) 01 �1.._.._............ co O o x as U C7 i CD m \ 0 Z CL o U I CV I M M N PATIO HEATER 50 MBH ••� 11 TMV-1 12 10 I 10 WC -1 _ .�.:% .... 4.;x;{3 IL o ...E Y a o 1 (I — i — A. 15A�l FD Kr' J� 1 1 ; � ��`•. ( �€ 1I 15 14 ! I a E .....:....... EQ .i _ _ E €( 1 Ean :. �-- -......... :€ I E i E is 8 LAY 4 48(+)24 48 (+)24 i 1 ul�I i i �t D 0 't3 131 1 � � I00 I E L- 13`I I 1 I -0 _ N 15 I 15 14 15 E D 1I1 / 6 6.4 f; — I I 1 ( j SHUT—OFF VALVE 1 I j3 E ;•••'; � � ^ � � � I � � � IN CEILING SPACE I 18 19 38 , TMV-1 12 f� ....................................... 3 k TMV-1 12 In N �II MATER + GAS SUPPLY PLAN - 1 2 1 2 TMV_ 1 12 PLUMBING BING S BOLS S.S. �.......� E TRAP PRIMER G W. GREASE WASTE LINE T.M.V. THERMOSTATIC MIXING VALVE -------V------- VENT LINE 1 2 TMV_ 1 12 PLUMBING BING S BOLS S.S. �.......� T.P. TRAP PRIMER G W. GREASE WASTE LINE T.M.V. THERMOSTATIC MIXING VALVE -------V------- VENT LINE T.P.R.V. TEMP. PRESSURE RELIEF VALVE NG GAS LINE +P.O.C. POINT OF CONNECTION — — COLD WATER LINE B.F.P. BACK FLOW PREVENTER — — — — — — ........ G.I./T. 1 2 TMV_ 1 12 WATER CALCULATIONS - PLUMBING BING S BOLS S.S. SANITARY SEWER LINE T.P. TRAP PRIMER G W. GREASE WASTE LINE T.M.V. THERMOSTATIC MIXING VALVE -------V------- VENT LINE T.P.R.V. TEMP. PRESSURE RELIEF VALVE NG GAS LINE +P.O.C. POINT OF CONNECTION — — COLD WATER LINE B.F.P. BACK FLOW PREVENTER — — — — — — HOT WATER LINE G.I./T. GREASE INTERCEPTOR/TRAP — — — — — TEMPERED WATER LINE LAV. LAVATORY — — — — — — FILTERED WATER LINE UR. URINAL — — — — — — — — — HOT WATER RECIRCULATION\ W.C. WATER CLOSET 3 SHUT—OFF VALVE G.R. GLASS RACK 2 BACKFLOW PREVENTER A.F.F. ABOVE FINISHED FLOOR V.T.R. VENT THRU ROOF B.F.F. BELOW FINISHED FLOOR C.I. CAST IRON Fm -1 WATER METER C.W. COLD WATER . • WATER HEATER H.W. HOT WATER E.C.O. EXTERIOR CLEAN—OUT T.W. TEMPERED WATER F.C.O. FLOOR CLEAN—OUT F.W. FILTER WATER W.C.O. WALL CLEAN—OUT F.S. FLOOR SINK M.S. MOP SINK F.D. FLOOR DRAIN S.S. SCULLERY SINK H.D. HUB DRAIN F.E.S. FABRICATED ECONOMY SINK F.F.D. FUNNEL FLOOR DRAIN H.S. HAND SINK K.F.D. KITCHEN FLOOR DRAIN U.B.S. UNDER BAR SINK R.F.D. RESTROOM FLOOR DRAIN U.B.H.S. UNDER BAR HAND SINK E.M. ELECTRICAL METER I.C.C. ICE CREAM CABINET G.M. GAS METER C WATER CALCULATIONS - HABIT BURGER PLUMBING FIXTURE QTY. WATER SUPPLY F.U. EACH WATER SUPPLY F.U. TOTAL LAVATORY 2 1 2 WATER CLOSET (FLUSH VALVE) 3 8 24 URINAL 1 5 5 3 -COMP SINK 1 4 4' MOP BASIN 1 3 3 1 BOWL PREP SINK 1 1.5 1.5 HAND SINK 4 1.5 6 WATERTO SODA/ICE 1 3 3 DUMP SINK 1 2 2 GAS PIPING SIZED PER TABLE 1216.2(1) OF THE 2012 UNIFORM PLUMBING CODE TOTAL LENGTH FROM METER TO PATIO HEATER = 300' TOTAL M t\O 50.5 (BASED ON TABLE A2.1,2012 UNIFORM PLUMBING CODE) 11/2" GAS LINE CALC. EQUIPMENT TAG MBH DISTANCE TO METER GAS LINE CONNECTION SIZE RTU -1 180 124' 3/4" RTU -2 224 172' 1-1/4" MAU-1 226 146' 1-1/4" FRYER (3 @ 80) 240 198' 3/4" CHAR BROILER 105 197' 3/4" GRIDDLE (2 @ 90) 180 220' 3/4" PATIO HEATER (2 @ 50) 100 249' 1/2" WATER HEATER 120 144' 11/4" TOTAL MBH 1375 GAS PIPING SIZED PER TABLE 1216.2(1) OF THE 2012 UNIFORM PLUMBING CODE TOTAL LENGTH FROM METER TO PATIO HEATER = 300' WATER/GAS SUPPLY KEYED NOTES O O NEW GAS WATER HEATER. SEE PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR ADDITIONAL INFORMATION. SET WATER TEMP. FOR 125'F. MAX. 2 1/2" COLD WATER AND 1/2- HOT WATER LINE DOWN INSIDE WALL TO HAND SINK. Q4 03 1/2" COLD AND HOT WATER LINE DOWN INSIDE WALL TO THREE COMPARTMENT SINK FAUCET AND 1/2- COLD AND HOT WATER LINES DOWN TO BELOW SINK FOR CHEMICAL FEED SYSTEM. 4 PROVIDE 1/2" COLD WATER CONNECTION FROM WATER FILTER TO ICE MAKER WITH BIN. O 1/2" COLD AND HOT WATER DOWN INSIDE WALL TO MOP SINK. O 1/2" COLD AND HOT WATER DOWN INSIDE WALL TO PREP SINK. O 1/2" FILTERED WATER DOWN IN WALL TO CARBONATOR. O 2 1/2" GAS PIPE UP THRU ROOF. SEE MEP100 FOR CONTINUATION. 9O 1/2" FILTERED WATER LINE DOWN INSIDE WALL AND BASE CABINET SPACE TO ICE MAKER AND TEA BREWER. CONTRACTOR TO PROVIDE APPROVED BACKFLOW PROTECTION DEVICE. SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. 10 1" COLD WATER INSIDE WALL TO WATER CLOSET. 11 1/2" COLD WATER AND 1/2" HOT WATER LINE DOWN INSIDE WALL TO LAVATORY. NEW THERMOSTATIC MIXING VALVE (TMV-1) SUPPLIED AND INSTALLED BY PLUMBING 12 CONTRACTOR BELOW SINK AND LAVATORIES AT LOCATIONS INDICTED. SET WATER TEMPERATURE FOR 1057 MAXIMUM. CIRCULATING HOT WATER TO RUN TO THE HOT WATER INLET OF TMV — SEE RISER DIAGRAM ON SHEET P400. SEE DETAIL 9/P410 FOR ADDITIONAL INFORMATION. 13 ROUTE 3/4" COLD WATER DOWN IN WALL TO WATER FILTER. FIELD VERIFY LOCATION. 14 3/4" COLD WATER INSIDE WALL TO URINAL. 15 ROUTE 1/2" COLD WATER PIPING BELOW FLOOR FROM TRAP PRIMER TO FLOOR DRAINS. FIELD VERIFY LOCATION. 16 CONNECT TO LANDLORD VALVED AND CAPPED 1 1/2" COLD WATER LINE IN CRAWL SPACE. FIELD VERIFY EXACT LOCATION PRIOR TO INSTALLATION OF SUB METER AND REMOTE READER. TENANT'S CONTRACTOR TO FURNISH AND INSTALL A SUB WATER METER W/REMOTE READER IN CEILING SPACE. COORDINATE LOCATION OF REMOTE READER WITH LANDLORD. 17 NEW 1 1/2" GAS DOWN TO GAS HEADER FOR COOKING EQUIPMENT. 18 PROVIDE MANUAL EMERGENCY GAS SHUT—OFF VALVE IN 2" GAS RISER DOWN TO COOKING EQUIPMENT. REFER TO GAS RISER DIAGRAM ON SHEET P400 FOR RISER FOR INFORMATION. PROVIDE AUTOMATIC EMERGENCY GAS SHUT—OFF VALVE IN 2" GAS RISER AND TIE INTO 19 ANSUL FIRE SUPPRESSION SYSTEM. REFER TO SHEET MECHANICAL HOOD DRAWINGS AND GAS RISER DIAGRAM ON SHEET P400 FOR INFORMATION. 20 1 1/4" MANIFOLD CONNECTION TO FRYERS, 3 FRYERS 0 80 CFH EACH. 21 3/4" GAS LINE TO GRIDDLE (90.0 MBH). TYPICAL OF 2 22 NEW HOT WATER RECIRCULATION WATER PUMP WITH INTEGRATED TIMER AND AQUASTAT. SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. SET TIMER FOR ON AT 8:30 A.M. AND OFF AT 11:00 P.M. DAILY. 23 NEW 1/2"CW WITH VALVE UP TO MAU-1 ON ROOF. COORDINATE LOCATION WITH MECHANICAL CONTRACTOR AND OWNERS REPRESENTATIVE. 24 3/4" GAS LINE DOWN TO CHAR ROCK BROILER (105 MBH). 25 NEW 1 1/2" GAS DOWN TO GAS HEADER FOR COOKING EQUIPMENT. 26 NEW 3/4"HW UP TO ITEM #78 ON ROOF. COORDINATE LOCATION WITH MECHANICAL CONTRACTOR AND OWNERS REPRESENTATIVE. 27 NG STUB UP. CONTRACTOR TO FURNISH AND INSTALL PATIO HEATER (50 MBH). PROVIDE DIRT LEG AND SHUTOFF VALVE WITH LOCKABLE HANDLE IN ACCORDANCE WITH LOCAL CODE. 28 NG DROP TO BELOW FLOOR INTO CRAWL SPACE, SEE GAS RISER DIAGRAM ON SHEET P400. 29 1 1/4" GAS PIPING DROP TO BELOW GRADE. SEE GAS RISER DIAGRAM ON SHEET P400. 30 1 1/4" GAS PIPE DOWN TO WATER HEATER (120 MBH). 31 NEW 1-1/2" WATER METER. LOCATE IN ACCESSIBLE LOCATION ABOVE CEILING. COORDINATE EXACT LOCATION OF SUB METER AND REMOTE READER WITH LANDLORD. 32 NEW 1-1/2" BACKFLOW PREVENTOR. SEE PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR ADDITIONAL INFORMATION. DRAIN INTO FLOOR DRAIN. FIELD VERIFY EXACT LOCATION. NOTE: 1. REFER TO RISER DIAGRAM ON SHEET P400 FOR PIPE SIZES. 2. REFER TO PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR KEYED NOTES O AND O . 3. REFER TO SHEET FOOD SERVICE DRAWINGS FOR PLUMBING ROUGH—IN INFORMATION. LINE TYPES: NATURAL GAS PIPING COLD WATER PIPING — — — — — — — FILTERED COLD WATER PIPING — — — — — — — — 110 DEG HOT WATER PIPING — — — — — — — — — 125 DEG HOT WATER PIPING — — — — — — HOT WATER RETURN PIPING — — — — — — — — — — — UNDER SLAB WATER PIPING REVIEW®F SCE CQMPLA City 4t -ru"lla 5upwG CNISION RECEIVED CITY OF TUKWILA JUN 10 2016 PERmrr CENTER VU 5 0 Mo M t\O co (D Lo in O Q cq ? ��Q 0 a�W C c_> NN CONTRACTOR FURNISHED AND INSTALLED SUB—WATER METER WITH REMOTE READER, COORDINATED WITH LANDLORD 1/21' 1 /2" LAY dol dop / 1/291 1 /2 „ r' �` " < \� 7 v` I.e\ ` 111/4" 3/4 ` 1 1/2" Y TP .� . ` r 6 0000`� WC) 3/41, `\ ` 1 /2,/ 1/211 ' 1 `.— 1 1/211 � LAV 1 1/2 %%% I II % r � 1 1/2 _ , 2 3 7 r' do' ' 1 1 2" ` 1/2"CW UP TO BFP 1 00 dop / _�``� MAU-1 ON ROOF /.• 3/4" 3/4" �#0 ` 1 1/2- 00 3/4" /'' .1, : ` 1 1 /211 /,/ -' //' 1 1 /2" 1 I f 16 ..I 3/4 ' 1 /' r . j/' .000 1 1 /2" I /'' 1 /2" 00 .0 1 1/4" 1 1/2 / ' 1 1/4"100 10 10 16 1 BFP-1 1/211 / 3/4" ./� /�REDUCED PRESSURE ' ' ' 1 1/4 �\ BACKFLOW PREVENTER / '• r /• 1 1/4" -r ;�/ 1 1/4" 1/2" (RPBFP) 1 45 .' `. �\ 1 /211 " r' ''�� ` `�` 1 1/4" I 1 1/2 -rte,/ ��16 ALARM PANEL WITHIN . a. 1/211 100 J`'•� / 1,/ /,r - 1 1/2°' SIGHT OF OV of BASIN BFP-2 6 i 0 / J ` ' 1" 1/2 TP 6.5 .. `�� 0.-< .0 / " DUPLEX SEWAGE 11 .�/ �� 1 1/4 12 II „ GRINDERS AND 1/211 in ��-3/4 14 �/, - '% 12 1 1/4" �I I I 1/2 5 SUMP BASINS �" J dop 3/49 1 r ' ` `. 111 �_ 1„ � Ie 37 1 /1 1, / • r 3/4„ 1 /2» r 6 FCO 7 1/2 00.0 1 1/4" I 11 6 7 -TE 00" ` 3/4„ 81 1 I 1/29f 6 00� rtop 00 �,• 5 7 //�, top .0 14 � 1» n r dop�� r 1/2" 1/2" V VIYIIV\VIVI\ IV 1..-IJVI\L /"�L UNDERGROUND WATER PIPING TO BE PROPERLY INSULATED 1/21' NOTE: ALL NEW WATER SUPPLY LINES ARE TO BE INSULATED C2 WATER RISER D 1 /2"CW FROM TRAP PRIMER- -1/2"V 3"- 1-1/2"V WCO 2'V AQQ--\ 3" 2'V D -1/2"V 3» F�4 >410 GREASE INTERCEPTOR 1 1 /2"SS _` WCO 2-1/2"V ;�N .LAY 2'V 1-1 /2'v--, FD 4Q 2, 2 3 3'j . ,1 / � 3" 2" 3" .100 rAj IISS u 4 3 2" 1/2 V UP, 1-1 " 3" VTR 2-1/ �-1 1/4" FORCED MAIN =� 2 1 /2'v 2"V UNDERFLOOR ` 1 1 9, FD TO EXISTING LIFT STATION ELEVATION: 25-1/2" BELOW UNDERSIDE OF FLOOR ABOVE EXISTING 4"SS _. 3" Wc 2-1 /2'N 1 1/4t FORCED MAIN 3" 2-1/2 —1/2 LAV \v FLOOR PENETRATION (TYPICAL) 1-1/2"V 211 SS 2'v- \ 2' VENT DERFLOOR 2"V 5411 FCO 9 op", ` 1-1/2' 1-1 /2"V 3" rr Gw 3 A ,' 311 �\ FS 2'v J T� ~ �� 3„ 3» �14 3" WCOv � �_-� If-" ` 15 2'v 2„ .r 1 /1 ``� FS G 31' )o 81 21f 211 3" r 3 WCO �' 31' WCO r- 3" 1-1/2"V 3 3" FD AQ NOTE: ALL NEW VENT PIPING PASSING THROUGH CEILING PLENUM AREA SHALL BE CAST IRON. fill P�l III! a m r 'b, OVA �lplp0%jf. aur 01206 3" FS 1, -AC -0 3" J 'WCO 2'V ELEVATION: 19" BELOW UNDERSIDE OF FLOOR ABOV 0 EXISTING ECO 3 RECEIVED CITY OF TUKWILA JUN 10 2016 PERMIT CENTER KEYED NOTES �1 1 1/2" DOWN TO WATER HEATER. O21 1 /2" FROM WATER HEATER. O3 1 /2"FW DOWN TO CARBONATOR. O4 CONNECT TO EXISTING WATER MAIN IN CRAWL SPACE. COORDINATE EXACT LOCATION IN FIELD. O5 1/2" COLD AND 1/2" HOT WATER DOWN TO CHEMICAL FEED SYSTEM. O 1/2" COLD WATER BELOW FLOOR TO FLOOR DRAIN. O THERMOSTATIC MIXING VALVE (TMV-1) BELOW FIXTURE. SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. �8 EXISTING 1 1/2"CW INSTALLED BY LANDLORD. U9 1/2" COLD WATER BELOW FLOOR FROM TRAP PRIMER. 10 EXTEND AND CONNECT NEW SANITARY PIPING TO EXISTING 4" SANITARY SEWER INSTALLED BY LANDLORD. VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FI ELD. 11 NEW 3" VENT PIPING UP, 4" VENT THRU ROOF. 12 EXTEND AND CONNECT NEW GREASE WASTE PIPING TO EXISTING 4" GREASE WASTE. VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FIELD. 13 LANDLORD INSTALLED 3" GAS PIPE TO LANDLORD INSTALLED GAS METER AT METER BANK. CONTRACTOR SHALL VERIFY EXACT GAS METER LOCATION, VERIFY METER HAS THE CAPACITY TO DELIVER A 945 MBH TOTAL DEMAND LOAD. 14 NEW 3/4"HW UP TO ITEM #78 ON ROOF. COORDINATE LOCATION WITH MECHANICAL CONTRACTOR AND OWNERS REPRESENTATIVE. 15 SEE DETAIL 12/P410 FOR ROUTING OF VENT PIPING IN HALF WALL. 16 1 1 /2" TO AND FROM RPZ BACKFLOW PREVENTER. 17 DELETED. 18 DELETED. 1 PATIO HEATER 50 MBH i -t w i rr.L.. (50 MBH) I ISEE DETAIL 4, THIS SHEET FOR CONTINUATION. 3"G ® 7" W.C. % (1375 MBH) > ON ROOF d' 3" CSD 7" W.C. (1375 MBH) ON ROOF 2-1/2" ® 7" W.C. (630 MBH) ON ROOF REDUCER MIN. 60 PSI RATED LINE SHUT-OFF VALVE - SEE GAS RISER DIAGRAM FOR CONTINUATION - 2 1/2" ® 7" W.C. (745 MBH) ON ROOF ROOF PENETRATION 2 1/2- ® 7" W.C. (745 MBH) 2-1/2" ® 7" W.C. (625 MBH) POUNDS TO INCHES LINE REGULATOR ADJUSTABLE UP TO AT LEAST 10" W.C., INLET RATED AT MIN. 60 PSIG 1 kit I C3 I I � GAS METER WITH NEW SERVICE AT METER BANK 1375 TOTAL MBH y, Y I NEW GAS SERVICE 0 2 PSI r RECEIVED CITY OF TUKWILA JUN 10 2016 PERMIT CENTER flEtv`lSlkj N GENERAL A. THE GENERAL CONDITIONS OF THE GENERAL SPECIFICATIONS, ALONG WITH ALL APPLICABLE INSTRUCTIONS TO BIDDERS SHALL FORM A PART OF THIS SECTION OF THE SPECIFICATIONS. B. REFERENCE IS MADE TO REQUISITES FOR BIDDERS AND CONTRACTORS UNDER OTHER SECTIONS OF THESE SPECIFICATIONS, WHICH SHALL BE CONSIDERED BINDING, UNLESS OTHERWISE NOTED UNDER THIS SECTION. SCOPE EACH CONTRACTOR SHALL THOROUGHLY ACQUAINT HIMSELF WITH THE CONSTRUCTION DETAILS, BOTH AS ON TENANT CONSTRUCTION DRAWINGS AND LANDLORD'S AS REFERRED TO, BEFORE SUBMITTING HIS BID AS NO ALLOWANCES WILL BE MADE BECAUSE OF THE CONTRACTOR'S UNFAMILIARITY WITH THESE DETAILS. ALL PERFORMANCE OF CONSTRUCTION SHALL BE AS REQUIRED BY THE PACE OF THE GENERAL CONSTRUCTION. INSPECTION OF SITE ALL PROPOSALS SHALL PRECLUDE THAT CONTRACTOR IS FAMILIAR WITH JOB SITE CONDITIONS AND UTILITY LOCATIONS AND THE LACK OF SPECIFIC INFORMATION ON THE DRAWINGS SHALL NOT RELIEVE THE CONTRACTOR OF ANY RESPONSIBILITY. PERMITS ALL PERMITS AND LICENSES NECESSARY FOR THE PROPER EXECUTION OF THE WORK SHALL BE SECURED AND PAID FOR BY THE SUBCONTRACTOR INVOLVED. CODE REQUIREMENTS ALL WORK UNDER THIS CONTRACT SHALL COMPLY WITH THE PROVISIONS OF THE SPECIFICATIONS, DRAWINGS OR AS DIRECTED BY THE OWNER, AND SHALL SATISFY ALL APPLICABLE CODES, ORDINANCES, OR REGULATIONS OF THE GOVERNING BODIES, WHETHER SO SHOWN OR NOT, AND ALL MODIFICATIONS REQUIRED BY SUCH AUTHORITIES SHALL BE MADE BY THE CONTRACTOR WITHOUT ANY ADDITIONAL COST TO THE OWNER. MATERIALS AND WORKMANSHIP A. ALL MANUFACTURED ARTICLES, MATERIALS, AND EQUIPMENT SHALL BE APPLIED AS RECOMMENDED BY THE MANUFACTURERS, AND UNLESS OTHERWISE SPECIFIED SHALL BE NEW, AND FREE FROM ANY DEFECTS. ALL LIKE MATERIALS USED SHALL BE OF THE SAME MANUFACTURE AND QUALITY UNLESS OTHERWISE SPECIFIED. B. ALL WORK UNDER THIS CONTRACT SHALL BE PERFORMED BY COMPETENT WORKMEN AND EXECUTED IN A NEAT AND WORKMANLIKE MANNER. WORK SHALL BE PROPERLY PROTECTED DURING CONSTRUCTION, AND ON COMPLETION, THE INSTALLATION SHALL BE THOROUGHLY CLEANED AND ALL DEBRIS PRESENT AS A RESULT OF THIS CONTRACT SHALL BE REMOVED FROM THE PREMISES, DO NOT JUST ABANDON. CODES AND REGULATIONS EACH SUBCONTRACTOR SHALL COMPLY WITH ALL LAWS, ORDINANCES, RULES AND REGULATIONS BEARING ON THE CONDUCT OF THE WORK AS DRAWN OR SPECIFIED. IF A SUBCONTRACTOR OBSERVES THAT THE DRAWINGS AND SPECIFICATIONS ARE AT A VARIANCE, HE SHALL PROMPTLY NOTIFY THE GENERAL CONTRACTOR AND THE TENANT IN WRITING. IF ANY SUBCONTRACTOR PERFORMS ANY WORK KNOWING IT TO BE CONTRARY TO LAWS, ORDINANCES, RULES AND REGULATIONS AND WITHOUT GIVING SUCH NOTICE, THE SUBCONTRACTOR SHALL BEAR ALL COSTS ARISING THEREFROM. PROTECTION OF WORK AND PROPERTY A. EACH SUBCONTRACTOR SHALL CONTINUOUSLY MAINTAIN ADEQUATE PROTECTION OF ALL HIS WORK FROM DAMAGE AND SHALL PROTECT THE OWNER'S PROPERTY FROM INJURY OR LOSS ARISING FROM HIS WORK. HE SHALL MAKE GOOD ANY SUCH DAMAGE, INJURY, OR LOSS, EXCEPT SUCH AS MAY BE DIRECTLY DUE TO CAUSES BEYOND HIS CONTROL AND NOT TO HIS FAULT OR NEGLIGENCE. HE SHALL ADEQUATELY PROTECT ADJACENT PROPERTY AS WELL. B. EACH SUBCONTRACTOR SHALL TAKE ALL NECESSARY PRECAUTIONS FOR THE SAFETY OF THEIR EMPLOYEES ON THE WORK AND SHALL COMPLY WITH ALL PROVISIONS OF FEDERAL, STATE AND LOCAL BUILDING CODES AND SAFETY LAWS TO PREVENT ACCIDENTS OR INJURY TO PERSONS ON OR ADJACENT TO THE PREMISES WHERE THE WORK IS BEING PERFORMED. EACH SUBCONTRACTOR SHALL MAINTAIN ALL INSURANCE REQUIRED TO PROTECT HIMSELF, OWNER AND TENANT FOR THE DURATION OF THE WORK AGAINST PROPERTY DAMAGE AND PUBLIC LIABILITY. CHANGES IN THE WORK THE TENANT, WITHOUT INVALIDATING THE CONTRACT, MAY ORDER EXTRA WORK OR MAKE CHANGES BY ALTERING, ADDING TO OR DEDUCTING FROM THE WORK, THE CONTRACT SUM BEING ADJUSTED ACCORDINGLY. COOPERATION ALL WORK UNDER THESE SPECIFICATIONS SHALL BE ACCOMPLISHED IN CONJUNCTION WITH OTHER CONTRACTORS AND TRADES OF THIS PROJECT IN A MANNER WHICH WILL ALLOW EACH CONTRACTOR AND TRADE ADEQUATE TIME AT THE PROPER STAGE OF CONSTRUCTION TO FULFILL HIS CONTRACTS. REFERENCE SHALL BE MADE TO THE OWNER FOR INSTRUCTIONS SHOULD ANY QUESTIONS ARISE BETWEEN TRADES AS TO THE PLACING OF LINES, DUCTS, CONDUITS, FIXTURES, OR EQUIPMENT, OR SHOULD IT APPEAR DESIRABLE TO REMOVE ANY GENERAL CONSTRUCTION WHICH WOULD AFFECT THE APPEARANCE OR STRENGTH OF THE STRUCTURE. SUBSTITUTION OF MATERIALS MANUFACTURER'S NAMES ARE LISTED HEREIN TO ESTABLISH A STANDARD. THE PRODUCTS OF OTHER MANUFACTURERS WILL BE ACCEPTABLE, IF IN THE OPINION OF THE OWNER OR OWNERS REPRESENTATIVE THRU A SUBMITTAL PROCESS, THE SUBSTITUTE MATERIAL IS OF A QUALITY AS GOOD OR BETTER THAN THE MATERIAL SPECIFIED, AND WILL SERVE WITH EQUAL EFFICIENCY AND DEPENDABILITY, THE PURPOSE FOR WHICH THE ITEMS SPECIFIED WERE INTENDED. SHOP DRAWINGS SHOP DRAWINGS AND CATALOG DATA ON ALL MAJOR ITEMS OF EQUIPMENT AND SYSTEMS, AND SUCH OTHER ILLUSTRATIVE MATERIAL AS MAY BE CONSIDERED NECESSARY BY THE TENANT, SHALL BE SUBMITTED BY THIS CONTRACTOR IN ADEQUATE TIME TO PREVENT DELAY AND CHANGES DURING CONSTRUCTION. DRAWINGS AND SPECIFICATIONS A. THE DRAWINGS SHOW DIAGRAMMATICALLY THE LOCATIONS OF THE VARIOUS LINES, DUCTS, CONDUITS, FIXTURES, AND EQUIPMENT AND THE METHOD OF CONNECTING AND CONTROLLING THEM. IT IS NOT INTENDED TO SHOW EVERY CONNECTION IN DETAIL AND ALL FITTINGS REQUIRED FOR A COMPLETE SYSTEM. B. SHOULD ANY CHANGES BE DEEMED NECESSARY BY THE CONTRACTOR IN ITEMS SHOWN ON CONTRACT DRAWINGS, THE SHOP DRAWINGS, DESCRIPTIONS, AND THE REASON FOR THE PROPOSED CHANGES SHALL BE SUBMITTED TO THE OWNER FOR APPROVAL. RESPONSIBILITY A. THE CONTRACTOR WILL BE HELD RESPONSIBLE FOR THE SATISFACTORY AND COMPLETE EXECUTION OF ALL WORK INCLUDED IN HIS CONTRACT. HE SHALL PRODUCE COMPLETE FINISHED OPERATING SYSTEMS AND PROVIDE ALL INCIDENTAL ITEMS REQUIRED AS PART OF HIS WORK, REGARDLESS OF WHETHER SUCH ITEM IS PARTICULARLY SPECIFIED OR INDICATED. GENERAL PROVISIONS 1. SCOPE: PROVIDE ALL LABOR, MATERIAL, AND EQUIPMENT IN ACCORDANCE WITH THESE SPECIFICATIONS AND THE ACCOMPANYING DRAWINGS TO PROVIDE A COMPLETE AND PROPERLY OPERATING PLUMBING SYSTEM FOR THE BUILDING. OBTAIN WATER, SEWER, GAS TAPS, AND ANY OTHER REQUIRED UTILITIES AND EXTEND SERVICE FROM SAME TO BUILDING AS SHOWN ON DRAWINGS. VISIT THE SITE FOR UNDERSTANDING OF THE WORK TO BE DONE BEFORE SUBMITTING BID. COORDINATE THIS WORK WITH THE WORK OF THE OTHER TRADES ON THE PROJECT. ALL PLUMBING IS TO BE ROUGHED IN WHILE THE BUILDING IS BEING CONSTRUCTED AT SUCH TIMES AS NOT TO DELAY THE GENERAL CONTRACTOR ON THE BUILDING. 2. GENERAL REQUIREMENTS: COMPLY WITH ALL FEDERAL, STATE, AND LOCAL REQUIREMENTS, CODES, RULES, AND ORDINANCES GOVERNING WORK OF THIS CHARACTER. PAY FOR AND OBTAIN NECESSARY CONSTRUCTION PERMITS AND CERTIFICATES OF INSPECTION. A. DRAWINGS: THE LOCATION OF THE PIPING RUNS ARE APPROXIMATE AND THE CONTRACTOR MUST MAKE ANY NECESSARY CHANGES IN THE PIPING RUNS, ETC., AT NO ADDITIONAL COST TO THE OWNER. OUTLET LOCATIONS ARE CRITICAL AND MUST BE LOCATED EXACTLY ACCORDING TO THE PLUMBING PLAN. COORDINATE THIS WORK WITH THE INSTALLERS OF EQUIPMENT FURNISHED AND INSTALLED BY OTHERS. REFER TO THE OTHER DRAWINGS FOR DETAILS OF THE BUILDING CONSTRUCTION AND THE OTHER MECHANICAL, ELECTRICAL, AND EQUIPMENT FEATURES. B. COORDINATION AND WORKMANSHIP: SCHEDULE THIS WORK SO THAT IT WILL BE PROPERLY COORDINATED WITH ALL OTHER TRADES. WORKMANSHIP SHALL BE IN ACCORDANCE WITH THE BEST PRACTICE FOR THE CLASS OF WORK INVOLVED. WORKMANSHIP SHALL ALLOW THE APPLIANCE TO OPERATE AS INTENDED AND BE INSTALLED TO BEST PROTECT THE PUBLIC AND OPERATORS FROM INJURY OR DAMAGE, AND TO PRESENT A NEAT, PLEASING, AND ORDERLY APPEARANCE. ' MATERIALS- AND PERFORMANCE 1. MATERIALS: i ALL MATERIALS SHALL BE NEW AND OF THE QUALITY INDICATED BY THE SPECIFIED BRAND NAMES. SUBSTITUTIONS OF MATERIAL OF EQUAL QUALITY BY OTHER FIRST-LINE MANUFACTURERS MAY BE ACCEPTABLE PROVIDED A LIST OF SUCH SUBSTITUTIONS IS APPROVED IN WRITING. A SUBSTITUTIONS LIST SHALL BE SUBMITTED IN TRIPLICATE WITHIN FIVE (5) DAYS AFTER THE CONTRACT IS LET. 2. BACKFILLING: PERFORM ALL NECESSARY EXCAVATING AND BACKFILLING REQUIRED FOR THIS INSTALLATION. PREPARE A PROPER BED OF SAND OR GRAVEL OR EQUIVALENT IN ROCK SCREENINGS SO AS TO ELIMINATE SHIMMING AND VOID SPACES UNDER ANY OF THE UTILITY SERVICE PIPES. BENDING OF ANY HARD PIPE WILL NOT BE PERMITTED. WHERE A CHANGE IN DIRECTION IS NECESSARY ON PRESSURE PIPES, "COMPATIBLE" COUPLINGS OR EQUAL SHALL BE USED AND BENDS MAY NOT EXCEED 90 DEGREES. ALL EXCAVATION BELOW THE BOTTOM OF FOOTINGS SHALL BE BACKFILLED WITH 2000 PSI CONCRETE. OTHER BACKFILL SHALL CONSIST OF 2-3" OF SAND OR ROCK SCREENINGS AND EARTH TO A FINAL LEVEL EQUAL TO ITS ORIGINAL CONDITION. IN THE EVENT THE BACKFILL SHOULD SETTLE BEFORE THE FINAL TOP SURFACE IS APPLIED, APPLY- ADDITIONAL BACKFILL TO SUSTAIN THE ORIGINAL LEVEL. CARE SHOULD BE TAKEN TO MINIMIZE THE DUST LEVEL WHEN EXCAVATING AND BACKFILLING SO AS TO COMPLY WITH FEDERAL AND STATE E.P.A. REGULATIONS RELATING TO THIS TYPE OF WORK (FUGITIVE DUST). 3. PIPING INSTALLATION: CLEAN -OUTS MUST BE INSTALLED ON MINIMUM DROP LINES EVEN THOUGH NOT SHOWN ON THE BLUEPRINTS. USE REDUCING FITTINGS IN MAKING REDUCTIONS IN SIZE OF PIPE. REAM ALL PIPE AFTER CUTTING, THEN TURN PIPES ON END AND KNOCK OUT ALL LOOSE DIRT AND SCALE BEFORE INSTALLING. MAKE CHANGES IN HORIZONTAL DIRECTION OF SOIL AND WASTE PIPES WITH LONG RADIUS FITTINGS OR WITH 'Y" BRANCHES AND 1/8 OR 1/16 BENDS. CONNECT SOIL STACKS AT BASE TO HORIZONTAL RUNS WITH 'Y" CONNECTIONS. WATER SUPPLY PIPES TO FIXTURES AND WASTE PIPES FROM FIXTURES SHALL BE CENTERED IN THE PROPER PLACE RELATIVE TO THE CENTER LINE OF THE FIXTURE. NO OFFSETS WILL BE ALLOWED. ALL PIPES SHALL BE RUN MECHANICALLY STRAIGHT AND SQUARE WITH BUILDING LINES, EXCEPT FOR REQUIRED PITCH ON HORIZONTAL LINES, AND ALL CHANGES IN DIRECTION SHALL BE MADE WITH FITTINGS. WATER PIPING TO BE ROUTED IN WALLS, UNDER THE FLOOR SLAB, AND ABOVE SUSPENDED CEILINGS AS NOTED. WHERE WATER LINES ARE ROUTED UNDER THE FLOOR SLAB, NO MECHANICAL JOINTS SHALL BE MADE UNDER THE SLAB EXCEPT AS LISTED BELOW. WATER PIPING SHALL BE INSTALLED NOT TO EXERT VERTICAL NOR HORIZONTAL STRESSES ON THE SEATING OF UNIONS. UNIONS SHALL BE COPPER TYPE NIBCO # 733 OR EQUAL. PROVIDE AIR CHAMBER TYPE WATER HAMMER ARRESTORS OR ACCEPTABLE FACTORY MANUFACTURED SUBSTITUTES AT ALL WATER ROUGH -IN LOCATIONS. NO WAX, PUTTY, OR VARNISH WILL BE PERMITTED. CRACKED FITTINGS SHALL BE REMOVED AND REPLACED WITH NEW FITTINGS. MAKE THREADED JOINTS IN BRASS PIPE AND FITTINGS WITH PIPE THREADING TO THE SHOULDER OF THE FITTINGS. NO SLIP JOINTS OR COUPLING JOINTS IN BRASS PIPE WILL BE PERMITTED, EXCEPT ON THE FIXTURE SIDE OF THE TRAP. 4. NATURAL GAS PIPING: FOR ABOVEGROUND INSTALLATIONS, ALL FITTINGS TO BE JOINED WITH TEFLON TAPE SEAL OR OTHER SUITABLE SEAL AND MADE IN CONFORMANCE WITH THE BEST PRACTICES OF AGA AND NFPA 54. UNIONS SHALL BE CAST BLACK IRON AND INSTALLED IN A MANNER SUCH THAT NO STRESS WILL BE PLACED ON THE MALE-FEMALE SEALING SURFACES. PROPER ALIGNMENT WILL BE MADE AT TIME OF INSTALLATION. ALL JOINTS AND CONNECTIONS SHALL BE THOROUGHLY CLEANED OF OIL, THREAD CUTTINGS AND RESIDUALS TO ACCEPT ENAMEL PAINT. ROUGH OR SHARP EXPOSED THREAD SURFACES SHALL BE FILED SMOOTH. 5. WATER PIPE: JOINTS SHALL BE CLEANED AND DEBURRED AS RECOMMENDED BY THE MANUFACTURER AND FEDERAL, STATE, AND LOCAL CODES AND SOLDERED AS LISTED BELOW. FLUX SHALL BE NON -CORROSIVE. ABOVE GRADE - WHERE FITTINGS ARE SOLDERED BOTH FITTINGS AND TUBING SHALL BE CLEANED AS DESCRIBED ABOVE. UNDER NO CIRCUMSTANCES SHALL DISSIMILAR METALS COME INTO DIRECT CONTACT WITH COPPER TUBING; E.G., GALVANIZED STRAPPING, HANGERS, OR CLAMPS TO SECURE THE TUBING. BELOW GRADE, OR FLOOR SLAB ON EARTH OR STONE FILL - HIGH TEMPERATURE, SOLDER, 1200 DEG. F OR GREATER MELTING POINT. NOTE: WATER PIPE TO BE PROPERLY SECURED AND ALIGNED SO AS NOT TO EXERT VERTICAL OR HORIZONTAL STRESSES ON THE SEATING OF THE MATING (MALE AND FEMALE) SURFACES OF THE UNIONS. A. MATERIALS - UNDERGROUND: TYPE "L" COPPER TUBE, SOFT TEMPER B. MATERIALS - ABOVEGROUND: TYPE "L" COPPER TUBE, HARD DRAWN. % C. INSULATION: INSULATION FOR HOT, COLD AND HOT WATER RECIRC. PIPING SHALL BE 1/2" (1" ON 1ST 8 FT. FROM HEATER) THICK ARMAFLEX UL LABELED OR FIBERGLASS 25 WITH ASJ/SSL FOIL/VINYL JACKET OR EQUAL. INSULATE ALL PIPING AND FITTINGS. 6. GAS PIPING A. UNDERGROUND GAS PIPING: ASTM A53, SCHEDULE 40 BLACK STEEL PIPE WITH LONG RADIUS STEEL WELDING FITTINGS INCLUDING CATHODIC PROTECTION OR POLYETHYLENE AS APPROVED BY LOCAL GAS COMPANY AND AUTHORITY HAVING JURISDICTION. B. GAS PIPING ABOVE GROUND: ASTM A53, SCHEDULE 40 BLACK STEEL WITH 125 POUND BLACK MALLEABLE IRON SCREWED FITTINGS. INSTALL MOISTURE TRAPS ON HVAC UNITS, WATER HEATER, AND KITCHEN EQUIPMENT. C. GAS PIPING COMPOUND AT JOINTS; IN COMPLIANCE WITH NFPA BULLETIN #54 AND LOCAL APPLICABLE CODES AND SUITABLE FOR NATURAL GAS SERVICE. 7. WASTE PIPING: INSTALL HORIZONTAL DRAIN AND WASTE PIPES WITH 1/4"/FT. SLOPE. MATERIALS: SOIL, WASTE AND VENT PIPING SHALL BE PVC SCH. 40 PIPING FOR SANITARY WASTE IN LIEU OF CAST IRON WHERE ALLOWED BY AUTHORITY HAVING JURISDICTION. PIPING SHALL NOT BE EXPOSED IN PLENUMS OR THE OPEN CEILING AREA IN THE DINING ROOM, CAST IRON - HUB TYPE WITH NEOPRENE JOINTS - WITH STAINLESS STEEL CONNECTORS WHEN PVC IS NOT ALLOWED PER LOCAL CODE. ALTERNATE BID ITEM CAST IRON NO HUB AND FITTINGS, WRAPPED WITH 3 MIL. PLASTIC, OR A.B.S. PIPING, BELOW SLAB OR GRADE ONLY, IF APPROVED BY LOCAL ADMINISTRATIVE AUTHORITY. INDIRECT WASTE PIPING TO BE IN COOLER/FREEZER, 3 COMPARTMENT SINK AND PREP SINK TO BE COPPER LINES FOR INDIRECT CONNECTION TO FLOOR SINK, CONDENSATE PIPING TO BE PVC. 8. PIPE SLEEVES/ESCUTCHEONS: PROVIDE CHROME -PLATED ESCUTCHEONS ON ALL PIPES PASSING THROUGH WALLS, FLOORS, OR CEILINGS OF FINISHED ROOMS. ESCUTCHEONS TO BE BEATON & CADWELL, #10, 40, 6A OR EQUIVALENT WITH SET -SCREWS. PROVIDE ESCUTCHEONS ON ALL WASTE LINES FROM PLUMBING FIXTURES, WHETHER THROUGH WALLS, FLOORS, AND WHETHER CONCEALED BEHIND COUNTERS OR EXPOSED. PIPE SLEEVES SHALL BE PROVIDED WHEN PIPES PENETRATE FOUNDATION AND SHALL BE 1" LARGER THAN PIPE, SEAL SLEEVE W/CAULKING. 9. PLUMBING FIXTURES: FURNISH AND INSTALL PLUMBING FIXTURES AS SHOWN ON DRAWINGS WITH ALL ACCESSORIES AND TRIM AS LISTED. ALL FIXTURES SHALL BE PROTECTED THROUGH THE COURSE OF THE CONSTRUCTION. ANY FIXTURE DAMAGED SHALL. BE REPLACED WITHOUT ADDITIONAL EXPENSE TO THE OWNER. 10. CONNECTION TO OTHER FIXTURES: CONNECT BUILDING SERVICE PIPING, INCLUDING BUT NOT LIMITED TO WATER, DRAIN, AND GAS PIPES TO FOOD SERVICE EQUIPMENT AS INDICATED IN EQUIPMENT SPECIFICATIONS. PROVIDE BACKFLOW PROTECTION ON ICE MACHINES AND BEVERAGE EQUIPMENT SUPPLY CONNECTIONS. 11. TESTS: A. DRAINAGE AND VENT PIPING - DRAINAGE AND VENT PIPING SHALL BE TESTED BEFORE THE PLUMBING FIXTURES ARE INSTALLED BY CAPPING THE OPENINGS AND FILLING THE ENTIRE SYSTEM WITH WATER AND ALLOWING IT TO STAND THUS FILLED NOT LESS THAN ONE (1) HOUR. INSPECT WATER LEVEL TO DETERMINE IF PIPING IS TIGHT. B. WATER PIPING - THE WATER SUPPLY PIPING LINES SHALL BE TESTED BEFORE THE PLUMBING FIXTURES ARE CONNECTED BY FILLING THE ENTIRE SYSTEM WITH POTABLE WATER AND APPLYING HYDROSTATIC PRESSURE OF 100 PSI AND ALLOWING TO STAND FOR NOT LESS THAN FOUR (4) HOURS AT THIS PRESSURE TO PROVE PLUMBING INTEGRITY. C. GAS PIPING - IN LIEU OF LOCAL REQUIREMENTS, GAS PIPING SHALL BE FILLED WITH COMPRESSED AIR TO 150 PSI AND HELD FOR A PERIOD OF FOUR (4) HOURS. EACH JOINT SHALL BE CHECKED BY LIQUID SOAP OR SPECIAL LIQUID CHEMICAL FOR LEAKS. NOTE: REMOVE ALL GAS VALVES AND PROTECT FROM DAMAGE BEFORE TESTING SYSTEM. 12. DISINFECTION OF POTABLE WATER SYSTEM: ALL SYSTEMS SHALL BE INITIALLY FLUSHED TO PURGE DELETERIOUS MATTER AND CONTINUE UNTIL POTABLE WATER APPEARS AT POINTS OF OUTLETS. UPON COMPLETION OF INSTALLATION AND INITIAL FLUSH, DISINFECT THE WATER SYSTEM PER PROCEDURE OF LOCAL JURISDICTION OR IF NONE SPECIFIED, BY FILLING IT WITH SOLUTION CONTAINING 50 PARTS PER MILLION OF CHLORINE AND ALLOW IT TO STAND FOR NOT LESS THAN TWENTY FOUR (24) HOURS BEFORE FLUSHING THOROUGHLY TO PURGE CHLORINE AND RETURNING/PUTTING IN TO SERVICE. ALTERNATELY USE.200 PPM FOR 3 HRS STANDING TIME. FURNISH CLEAN WATER SAMPLES TO THE LOCAL AUTHORITY FOR TESTING AFTER THE LINES HAVE BEEN DISINFECTED. THIS PROCEDURE TO BE IN ACCORDANCE WITH STATE PLUMBING CODE. 13. CLEANUP: CLEAN ALL PLUMBING FIXTURES AND EQUIPMENT THOROUGHLY BEFORE FINAL INSPECTION, LEAVING ALL READY FOR USE. 14. GUARANTEE: MATERIALS AND WORKMANSHIP SHALL BE GUARANTEED FOR ONE (1) YEAR FROM DATE OF FINAL ACCEPTANCE. DEFECTIVE WORK AND ALL DAMAGES CAUSED THEREBY WHICH MAY OCCUR DURING THE TERM OF THE AFOREMENTIONED GUARANTEE WILL BE REPAIRED AND/OR REPLACED AT NO EXPENSE TO THE OWNER. 15. OWNER'S MANUAL: PROVIDE THE OWNER, AT THE COMPLETION OF THIS CONTRACT, WITH AN "OWNER'S MANUAL" SO LABELED. THE MANUAL SHALL CONSIST OF A THREE-RING LOOSE-LEAF BINDER CONTAINING ALL PRINTED MATTER SUCH AS: GUARANTEE CARDS, CLEANING INSTRUCTIONS, NOTICES TO OWNER, OPERATING MANUALS, AND MAINTENANCE INSTRUCTIONS THAT MAY BE CONTAINED IN THE SHIPPING CARTONS OR..EQUIPMENT HOUSINGS. S v f C, PLUMBING FIXTURE o%.oHEDULE FIXTURE DATA CONNECTION DATA MARK DESCRIPTION CW HW WASTE' GAS 2.1 EVAPORATOR COIL - COOLER 1" INDIRECT DRAIN PLAN FIXTURE QTY. MFG. PROVIDED SOIL VENT TRAP INDIRECT WATER 2" COLD HOT TW FILTER TAG 6.4 BY SIZE SIZE WASTE 6.5 HOSE BIBB FOR CHEMICAL DISPENSER 1/2" @ 48" A.F.F. AMERICAN 7 BAG -N -BOX 1/2" @ 24" A.F.F. 9 WATER HEATER ADA COMPLIANT, ELONGATED BOWL, VITEROUS CHINA, 1.28 GPF, WC -1 WATER CLOSET 2 STANDARD GENERAL 4" 2" INTEGRAL ----- 1/2" --- --- ___ SEAT: BEAMIS #1955C OPEN FRONT, WHITE. TRIP LEVER TO BE 12.1 HANDICAPPED 1/2" @ 16" A.F.F. 2857.128 CONTRACTOR 14 SELF CONTAINED ICE MAKER (BOH) 1/2" @ 66" A.F.F. 3/4" INDIRECT DRAIN 15 ON THE WIDE SIDE OF STALL. SLOAN ROYAL WES-111 DUAL 3/4" INDIRECT DRAIN 16 3 COMPARTMENT SINK 11/2" TYPE "M" COPPER TO FS 17 PRE-RINCE UNIT W/FAUCET 1/2" @ 16" A.F.F. FLUSH 24 AMERICAN 240 MBH 25 CHAR -ROCK BROILER 4" CENTERS WALL MOUNTED, AMERICAN STANDARD MODEL LAV LAVATORY 2 STANDARD GENERAL 1-1/2" 1-1/2" 1 -1/2" ----- 1/2" --- 1/2" ___ 1,340M.119 METERING FAUCET, .5 GPM, 0.083 GPC, PROVIDED 11/2" @ 14" A.F.F. 0356.421 CONTRACTOR HAND SINK FAUCET 1/2" @ 16" A.F.F. 1/2" @ 16" A.F.F. 38 WALL MTD HAND SINK WITH MECHANICAL MIXING VALVE, PROVIDE AMERICAN STANDARD 11/2" @ 16" A.F.F. 38.1 LOW LEAD FAUCET 1/2" @ 16" A.F.F. 1/2" @ 16" A.F.F. 45 ICE TEA 1/2"FCW 0 24" A.F.F. 605P.400 4" DECK PLATE 46 SODA DISPENSER 1/2" FCW @ 24" A.F.F. AMERICAN SEPARATE 1" INDIRECT DRAIN 46.1 ICE MACHINE (FOH) 1/2" FCW @ 60" A.F.F. SEPARATE 1" INDIRECT DRAIN 46.4 ADA COMPLIANT, VITREOUS CHINA, LOW CONSUMPTION (0.125 UR URINAL 1 STANDARD GENERAL 2" 1 1/2" 2"----- 3/4" --- --- --_ GPF), SIPHON JET ACTION, 3/4" INLET SPUD, 2" OUTLET. SLOAN 11/2" @ 8" A.F.F. 81.1 6590.503 CONTRACTOR 1/2"1 1RWRFED ROYAL FLUSHOMETER MODEL 186-0.125 HIGH EFFICIENCY MANUAL FLUSH VALVE, .125 GPF FD FLOOR DRAIN 11 J.R. SMITH GENERAL 3" 1 1/2" 3" ----- --- --- --- -__ WITH BRONZE STRAINER, DOUBLE DRAINAGE FLANGE, WEEP 2005 SERIES CONTRACTOR HOLES AND TRAP PRIMER WATTS GENERALCAST IRON BODY WITH WHITE PORCELAIN COATED INTERIOR, WITH FS FLOOR SINK 6 3" 1 1/2" 3" ----- --- --- --- -- ALUMINUM DOME BOTTOM STRAINER AND LOOSE SET PORCELAIN FS -740 CONTRACTOR ENAMEL COATED CAST IRON HALF GRATE. HOLD CENTER LINE OF FLOOR SINK 14" FROM WALL. TRAP PRECISION GENERAL MODEL #PR50OAUS, ALL BRONZE TRAP PRIMER WITH REMOVABLE TP PRIMER 11 PLUMBING CONTRACTOR ___ -__ ___ _____ 1/2„ __- ___ --- OPERATING PARTS, INTEGRAL PRODUCTS VACUUM BREAKER GASKETED ACCESS COVER AND CHROME PLATED. THERMOSTATIC WATER MIXING VALVE MODEL e480-00, INTEGRAL COMBINATION CHECK STOPS WITH STRAINERS, TEMPERATURE TMV-1 THERMOSTATIC 7 POWERS GENERAL ___ ___ ___ _____ 1/2" 1/2" 1/2" _ RANGE: 80 TO 140 DEG., FLOW CAPACITY OF A MINIMUM OF .5 MIXING VALVE CONTRACTOR IN IN OUT GPM TO MAX 12 GPM, BRONZE BODY, INTEGRAL FILTER WASH, CHECK VALVES, ADJUSTMENT CAP WITH LOCKING FEATURE, 0.5 GPM MINIMUM FLOW. WALL J.R. SMITH GENERAL CAST IRON CAULKING FERRULE WITH BRASS RAISED HEAD PLUS WCO CLEANOUT 14 4420 SERIES CONTRACTOR VARIES --- --- ----- --- --- --- --- POLISHED NICKEL ALLOY OR STAINLESS STEEL COVER PLATE. SECURE WITH SCEW SPIGOT CONNECTION. FCO FLOOR 4 J.R. SMITH GENERAL „ 4 ___ ___ ___ _ ___ ___ ___ ___ LEVELEZE COATED CAST IRON BODY WITH ADJUSTABLE HOUSING, CLEANOUT 4020 SERIES CONTRACTOR SATIN NICKEL ALLOY TOP AND INSIDE CAULK CONNECTION. OWNER GAS WATER HEATER, MODEL BTH-120, 120,000 BTH, 60 GALLON, WH WATER 1 A. 0. SMITH FURNISHED _-- -_- ___ ----- 1 1/2" 1 1/2" --- --- 173 GPH RECOVERY 0 80 DEG. TEMP RISE, SET OUTLET WATER HEATER CONTRACTOR TEMPERATURE AT 125' F.. PIPE T&P FULL SIZE TO NEAREST DRAIN. INSTALLED PROVIDE A. 0. SMITH EXPANSION TANK, MODEL ST -25-V. OWNER GRUNDFOS MODEL UP -15 -29 -SF -T, SET PUMP TO PROVIDE A CP1 RECIRCULATION 1 GRUNDFOS FURNISHED___ ___ __- ----- 1/2" ___ ___ ___ MAXIMUM OF 2 GPM THRU THE SYSTEM AT 10 FT. HEAD PLUS PUMP CONTRACTOR PIPING . LOSSES, INTEGRATED TIMER; 115V, .022 AMPS, 25 WATTS, INSTALLED 1/25 HP. BACKFLOW 1 PREVENTER GENERAL MODEL LF009QT, BRONZE BODY CONSTRUCTION, QUARTER TURN BFP1 SODA MACHINE WATTS CONTRACTOR ___ ___ ___ ----- 1/2" --- --- --- BALL VALVES, USC APPROVED. CERTIFIED TEST PREFORMED BEFORE / CARBONATOR TURN OVER TO HABIT BURGER. BACKFLOW LF007QT, DUAL CHECK BACKFLOW PREVENTER, BRONZE BODY BFP2 PREVENTER 1 WATTS GENERAL ___ ___ ___ _____ 1/2" __- --- --- CONSTRUCTION, QUARTER TURN BALL VALVES, USC APPROVAL, TEA BREWER CONTRACTOR I CERTIFIED TO ANSI/NSF STANDARD 18. CERTIFIED TEST PREFORMED BEFORE TURN OVER TO HABIT BURGER. RPBFP BOLDING BACKFLOW 1 WATTS GENERAL I MODEL LF009QT, BRONZE BODY CONSTRUCTION, QUARTER TURN PREVENTER CONTRACTOR --_ ___ --- _____ 1 1/2" --- --- --- BALL VALVES, USC APPROVED. CERTIFIED TEST PREFORMED BEFORE TURN OVER TO HABIT BURGER. BRASS VALVE BODY, OVAL METAL WHEEL HANDLE, 3/4" FEMALE #78 POST HYDRANT 1 WOODFORD MODEL Y30GENERAL __- -_- --- ----- 3/4" ___ -__ INLET, 3/4" BRASS MALE HOSE NOZZLE OUTLET, 1" GALVANIZED CONTRACTOR STEEL PIPE, 1/8- DRAIN PIPED TP NEAREST FLOOR SINK AND TERMINATED WITH CODE APPROVED AIR GAP CONTRACTOR NOTE: WATER HEATER, EXPANSION TANK AND DOMESTIC HOT WATER RECIRCULATION PUMP TO BE FURNISHED BY OWNER AND INSTALLED BY THE CONTRACTOR. CONTRACTOR TO FURNISH AND INSTALL ALL PIPING, FITTINGS AND VALVING REQUIRED FOR A COMPLETE AND WORKING SYSTEM. THE CHEMICAL INJECTION SYSTEMS ARE SUPPLIED BY BUTLER CHEMICAL AND THEY UTILIZE ENMESHED AIR GAPS AS A MEANS OF BACKFLOW PREVENTION. IF PRESSURE REQUIRES, BUTLER CHEMICAL WILL SUPPLY A SEPARATE VALVE TO ADJUST THE PRESSURE AS REQUIRED. COPY &,b_.ZMc7 er , at , Pin z ;,�y, , ;_d res :f , suhjsct to errors and c 1 wi �ro dnor^4P' Ike �I"•"1 p'0^�'4(+i: �r iw and, i�.. :�:d,J i:r F, Date: City 014 1-Ilkwila BUILDING DIVISION No chanass shop bo made to the sa of 1"" rlt vv thn!.;t prior opprovol Of la Cttilding Division, iQn, %vial rcquiro a new plan submittal and may in�;ludQ additional plan review tees, I bQDB,CC.IIPLIANCB APPROVED t/A1 TPR 13 2016 __ O EQUIPMENT & FIXTURE SCHEDULE - PLUMBING MARK DESCRIPTION CW HW WASTE' GAS 2.1 EVAPORATOR COIL - COOLER 1" INDIRECT DRAIN 2.4 EVAPORATOR COIL - FREEZER 1" INDIRECT DRAIN 6 JANITORS SINK 2" 6.2 JANITORS SINK - FAUCET W/VAC BRKR 1/2" @ 42" A.F.F. 1/2" @ 42" A.F.F. 6.4 CHEMICAL DISPENSER 6.5 HOSE BIBB FOR CHEMICAL DISPENSER 1/2" @ 48" A.F.F. 7 BAG -N -BOX 1/2" @ 24" A.F.F. 9 WATER HEATER SEE WATER HEATER SCHEDULE 10 WATER FI LTER SYSTEM 3/4" 9 96" A. F. F. 1/2" 1 N DI RECT DRAI N 12 PREP TABLE W/SINK 11/2" TYPE "M" COPPER TO FS 12.1 PREP TABLE FAUCET 1/2" @ 16" A.F.F. 1/2" @ 16" A.F.F. 14 SELF CONTAINED ICE MAKER (BOH) 1/2" @ 66" A.F.F. 3/4" INDIRECT DRAIN 15 ICE BIN 3/4" INDIRECT DRAIN 16 3 COMPARTMENT SINK 11/2" TYPE "M" COPPER TO FS 17 PRE-RINCE UNIT W/FAUCET 1/2" @ 16" A.F.F. 1/2" @ 16" A.F.F. 24 FRYER (3) 240 MBH 25 CHAR -ROCK BROILER 105 MBH 27 GRIDDLE 90 MBH 27.1 GRIDDLE 90 MBH 37 S.S. HAND SINK 11/2" @ 14" A.F.F. 37.1 HAND SINK FAUCET 1/2" @ 16" A.F.F. 1/2" @ 16" A.F.F. 38 WALL MTD HAND SINK 11/2" @ 16" A.F.F. 38.1 LOW LEAD FAUCET 1/2" @ 16" A.F.F. 1/2" @ 16" A.F.F. 45 ICE TEA 1/2"FCW 0 24" A.F.F. 46 SODA DISPENSER 1/2" FCW @ 24" A.F.F. SEPARATE 1" INDIRECT DRAIN 46.1 ICE MACHINE (FOH) 1/2" FCW @ 60" A.F.F. SEPARATE 1" INDIRECT DRAIN 46.4 CARBONATOR 1/2" FCW @ 60" A.F.F. 1" INDIRECT DRAIN 78 HOSE BIBB 1/2" @ ROOF 81 HAND SINK 11/2" @ 8" A.F.F. 81.1 HAND SINK FAUCET 1/2" @ 12" A.F.F. 1/2"1 1RWRFED ,S 1.71AT E PL=P,%IIT _-2U1'1:D FOR: .1echanicd gWccjical ❑ Plumbing ❑ Gas at, • $ '' MAR 2 1 2016 TUKWILA PUBLIC WORKS CORRECTION LTR#--j_�L G RECEIVED CITY OF WK IL. MAR 17 2016 PERPAIT. CENTER ro SCALS 114C T -W zrTO EXISTING LIFT STATION 4-8: X 4"SS Nip ELEVATION: 25-1/2" BELOW SUBFLOOR EXISTING CLEANOUT ELEVATION: 19" BELOW SUBFLOOR GREASE TRAP CALCULATIONS 3 COMPARTMENT SINK (20) 18 * 24 * 14 = 6048 SANITARY SEWER LINE T.P. 6048 * 3 = 18144 G.W. 18144 / 231 = 78.5455 T.M.V. 78.545 * 75% = 58.9091 GAL. -------V------- MOP BASIN (GC -6) 24 * 24 * 10 = 5760 TEMP. PRESSURE RELIEF VALVE 5760 / 231 = 24.9351 - GAS LINE 24.935 * 75% 1 = 18.7013 GAL. POINT OF CONNECTION 2 HANDSINKS (21) 12 * 10 * 5 = 600 BACK FLOW PREVENTER - - - - - 600 / 231 = 2.5974 G.I./T. GREASE INTERCEPTOR/TRAP - - - - 2.5974 * 75% = 1.94805 GAL. LAV. LAVATORY PREP SINK (22) 18 * 20 * 14 = 5040 SHUT-OFF VALVE W.C. 5040 / 231 = 21.81$2 BACKFLOW PREVENTER G.R. GLASS RACK V.T.R. 21.818 * 75% = 16.3636 GAL. A.F.F. ABOVE FINISHED FLOOR TOTAL CAPACITY 58.909 + 118.7011 + 1 0 1 + 116.3636364 11 93.97 GAL. BELOW FINISHED FLOOR 93.974 GPM FOR 1 MINUTES 46.987 GPM FOR 2 MINUTE a°=vlkVVED FOR .CODE COMPLIANCE APPROVED +r APR 13 2016 NOTE: 1. REFER TO RISER DIAGRAM ON SHEET P400 FOR PIPE SIZES. 2. REFER TO PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR KEYED NOTES O AND O . 3. INDIRECT WASTE PIPES EXCEEDING 5 FEET, BUT LESS THAN 15 FEET IN LENGTH SHALL BE DIRECTLY TRAPPED, BUT SUCH TRAPS NEED NOT BE VENTED PER SECTION 803.1 OF THE 2013 CALIFORNIA PLUMBING CODE, LTE TYPES SS SANITARY PIPING GW GREASE WASTE PIPING - CD - CD CD CD - CONDENSATE PIPING --------------------- VENT PIPING O NEW HAND SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW PREP SINK. ROUTE 1 1/2" COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW ICE MAKER WITH BIN. ROUTE INDIRECT WASTE TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW URINAL. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW MOP SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. ONEW 3 COMP SINK. ROUTE 1 1/2" COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. �j NEW CARBONATOR/SODA RACK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. �8 NEW SODA MACHINE W/ICE MAKER ABOVE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW ICE TEA BREWER. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 10 NEW WATER CLOSET. REFER TO PLUMBING FIXTURE SCHEDULE FOR INFORMATION. 11 NEW LAVATORY. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 12 NEW FLOOR DRAIN. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 13 1 1/4" CONDENSATE DRAIN FROM RTU -1, RTU -2 AND MAU-1 DOWN IN WALL AND TERMINATE INTO MOP BASIN WITH CODE APPROVED AIR GAP. 14 NEW FLOOR SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 15 NEW WALL CLEAN-OUT. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 16 PROVIDE 4" CONDUIT FOR SODA LINES IN WALL. 17 4" GREASE WASTE TO GALLON GREASE INTERCEPTOR, FURNISHED AND INSTALLED BY LANDLORD. SEE PROJECT CIVIL DRAWINGS FOR ADDITIONAL DETAILS AND LOCATION. 18 EXTEND AND CONNECT NEW 4" SANITARY PIPING TO EXISTING 4" SANITARY SEWER PIPING. VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FIELD. 1 g NEW 3" VENT UP AND CONNECT TO LANDLORD CAPPED 4" VENT THRU ROOF. CONTRACTOR TO PROVIDE VENT PIPING EXTENSIONS TO ENSURE VENT PIPING IN HIGHER THAN PARAPET. ENSURE VENT THRU ROOF IS AT LEAST 10'-0" AWAY FROM ALL OUTSIDE AIR INTAKES. FIELD VERIFY LOCATION. 20 ROUTE CONDENSATE DRAIN FROM COOLER AND FREEZER TO FLOOR SINK. SEE RISER DIAGRAM FOR ADDITIONAL INFORMATION. 21 NEW GAS WATER HEATER INSTALLED ON CONCRETE CURB. SEE ARCHITECTURAL DRAWINGS FOR CURB DETAILS. SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL WATER HEATER INFORMATION. 22 WATER FILTER SYSTEM. REFER TO EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. 23 ROUTE SODA LINES WITHOUT CONDUIT FROM BAG -N -BOX OVERHEAD AND DROP IN NEARBY WALL WITH CONDUIT AT SODA DISPENSER. COORDINATE DROP IN FIELD WITH SODA VENDOR. FIELD VERIFY LOCATION. 24 1 1/2" DRAIN UP THRU ROOF TO MAU-1. COORDINATE LOCATION THE MECHANICAL CONTRACTOR. 25 1 /2"CW FROM TRAP PRIMER. SEE WATER RISER DIAGRAM AND PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. 26 TRAPZILLA MODEL #TZ -1826 100 GPM INTERIOR GREASE INTERCEPTOR. MOUNT 18 INCHES BELOW SUBFLOOR WITH COLLAR EXTENSIONS TO SUBFLOOR. USE TRAPZILLA COVER MODEL #FTCA-22. SEE SHEET P420 FOR DETAILS. SEE STRUCTURAL DRAWINGS FOR MOUNTING FRAME. 27 ALL PIPING UNDER SUBFLOOR TO BE HUNG FROM SUBFLOOR IN CRAWLSPACE. 28 DROP SANITARY PIPING DOWN TO AVOID STRUCTURAL BEAM. FIELD VERIFY LOCATION. SLOPE PIPE AT 1/8- PER FOOT TO CONNECT WITH EXISTING SANITARY MAIN. SEE RISER DIAGRAM ON SHEET P400 FOR ADDITIONAL INFORMATION. RECEI EnD CITY O `I U IWALA MAR 17 2016 PERMIT CENTER PLUMM SYMWLS S.S. SANITARY SEWER LINE T.P. TRAP PRIMER G.W. GREASE WASTE LINE T.M.V. THERMOSTATIC MIXING VALVE -------V------- VENT LINE T.P.R.V. TEMP. PRESSURE RELIEF VALVE - - - - - - - - GAS LINE *P.O.C. POINT OF CONNECTION WATER LINE B.F.P. BACK FLOW PREVENTER - - - - - - HOT WATER LINE G.I./T. GREASE INTERCEPTOR/TRAP - - - - - TEMPERED WATER LINE LAV. LAVATORY - • - • - • - - - FILTERED WATER LINE UR. URINAL SHUT-OFF VALVE W.C. WATER CLOSET BACKFLOW PREVENTER G.R. GLASS RACK V.T.R. VENT THRU ROOF A.F.F. ABOVE FINISHED FLOOR C.I. CAST IRON BELOW FINISHED FLOOR C.W. COLD WATER Iff. WATER METER H.W. HOT WATER W.H. WATER HEATER T.W. TEMPERED WATER E.C.O. EXTERIOR CLEAN-OUT F.W. FILTER WATER F.C.O. FLOOR CLEAN-OUT F.S. FLOOR SINK W.C.O. WALL CLEAN-OUT F.D. FLOOR DRAIN M.S. MOP SINK H.D. HUB DRAIN S.S. SCULLERY SINK F.F.D. FUNNEL FLOOR DRAIN F.E.S. FABRICATED ECONOMY SINK K.F.D. KITCHEN FLOOR DRAIN H.S. HAND SINK R.F.D. RESTROOM FLOOR DRAIN U.B.S. UNDER BAR SINK E.M. ELECTRICAL METER U.B.H.S. UNDER BAR HAND SINK G.M. GAS METER I.C.C. ICE CREAM CABINET LTE TYPES SS SANITARY PIPING GW GREASE WASTE PIPING - CD - CD CD CD - CONDENSATE PIPING --------------------- VENT PIPING O NEW HAND SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW PREP SINK. ROUTE 1 1/2" COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW ICE MAKER WITH BIN. ROUTE INDIRECT WASTE TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW URINAL. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW MOP SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. ONEW 3 COMP SINK. ROUTE 1 1/2" COPPER WASTE PIPE WITH INDIRECT CONNECTION TO FLOOR SINK. PROVIDE AIR GAP PER CODE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. �j NEW CARBONATOR/SODA RACK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. �8 NEW SODA MACHINE W/ICE MAKER ABOVE. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. O NEW ICE TEA BREWER. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 10 NEW WATER CLOSET. REFER TO PLUMBING FIXTURE SCHEDULE FOR INFORMATION. 11 NEW LAVATORY. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 12 NEW FLOOR DRAIN. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 13 1 1/4" CONDENSATE DRAIN FROM RTU -1, RTU -2 AND MAU-1 DOWN IN WALL AND TERMINATE INTO MOP BASIN WITH CODE APPROVED AIR GAP. 14 NEW FLOOR SINK. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 15 NEW WALL CLEAN-OUT. REFER TO PLUMBING EQUIPMENT SCHEDULE FOR INFORMATION. 16 PROVIDE 4" CONDUIT FOR SODA LINES IN WALL. 17 4" GREASE WASTE TO GALLON GREASE INTERCEPTOR, FURNISHED AND INSTALLED BY LANDLORD. SEE PROJECT CIVIL DRAWINGS FOR ADDITIONAL DETAILS AND LOCATION. 18 EXTEND AND CONNECT NEW 4" SANITARY PIPING TO EXISTING 4" SANITARY SEWER PIPING. VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FIELD. 1 g NEW 3" VENT UP AND CONNECT TO LANDLORD CAPPED 4" VENT THRU ROOF. CONTRACTOR TO PROVIDE VENT PIPING EXTENSIONS TO ENSURE VENT PIPING IN HIGHER THAN PARAPET. ENSURE VENT THRU ROOF IS AT LEAST 10'-0" AWAY FROM ALL OUTSIDE AIR INTAKES. FIELD VERIFY LOCATION. 20 ROUTE CONDENSATE DRAIN FROM COOLER AND FREEZER TO FLOOR SINK. SEE RISER DIAGRAM FOR ADDITIONAL INFORMATION. 21 NEW GAS WATER HEATER INSTALLED ON CONCRETE CURB. SEE ARCHITECTURAL DRAWINGS FOR CURB DETAILS. SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL WATER HEATER INFORMATION. 22 WATER FILTER SYSTEM. REFER TO EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. 23 ROUTE SODA LINES WITHOUT CONDUIT FROM BAG -N -BOX OVERHEAD AND DROP IN NEARBY WALL WITH CONDUIT AT SODA DISPENSER. COORDINATE DROP IN FIELD WITH SODA VENDOR. FIELD VERIFY LOCATION. 24 1 1/2" DRAIN UP THRU ROOF TO MAU-1. COORDINATE LOCATION THE MECHANICAL CONTRACTOR. 25 1 /2"CW FROM TRAP PRIMER. SEE WATER RISER DIAGRAM AND PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. 26 TRAPZILLA MODEL #TZ -1826 100 GPM INTERIOR GREASE INTERCEPTOR. MOUNT 18 INCHES BELOW SUBFLOOR WITH COLLAR EXTENSIONS TO SUBFLOOR. USE TRAPZILLA COVER MODEL #FTCA-22. SEE SHEET P420 FOR DETAILS. SEE STRUCTURAL DRAWINGS FOR MOUNTING FRAME. 27 ALL PIPING UNDER SUBFLOOR TO BE HUNG FROM SUBFLOOR IN CRAWLSPACE. 28 DROP SANITARY PIPING DOWN TO AVOID STRUCTURAL BEAM. FIELD VERIFY LOCATION. SLOPE PIPE AT 1/8- PER FOOT TO CONNECT WITH EXISTING SANITARY MAIN. SEE RISER DIAGRAM ON SHEET P400 FOR ADDITIONAL INFORMATION. RECEI EnD CITY O `I U IWALA MAR 17 2016 PERMIT CENTER _o . PATIO HEATER 50 MBH 6 . i �•—TMV-1 12 WATER CALCULATIONS - PLUINOM, SYMBOLS S.S.- SANITARY SEWER LINE T.P. TRAP PRIMER G.W.— GREASE WASTE LINE T.M.V. THERMOSTATIC MIXING VALVE -------V------- VENT LINE T.P.R.V. TEMP. PRESSURE RELIEF VALVE NC GAS LINE *P.O.C. POINT OF CONNECTION — — COLD WATER LINE B.F.P. BACK FLOW PREVENTER — — — — — — HOT WATER LINE G.I./T. GREASE INTERCEPTOR/TRAP — — — — — TEMPERED WATER LINE LAV. LAVATORY — — — — — — FILTERED WATER LINE UR. URINAL — — — — — — — — — HOT WATER RECIRCULATION\ W.C. WATER CLOSET 3 SHUT—OFF VALVE G.R. GLASS RACK 2 BACKFLOW PREVENTER A.F.F. ABOVE FINISHED FLOOR V.T.R. VENT THRU ROOF B.F.F. BELOW FINISHED FLOOR C.I. CAST IRON ❑M WATER METER C.W. COLD WATER W.H. WATER HEATER H.W. HOT WATER E.C.O. EXTERIOR CLEAN—OUT T.W. TEMPERED WATER F.C.O. FLOOR CLEAN—OUT F.W. FILTER WATER W.C.O. WALL CLEAN—OUT F.S. FLOOR SINK M.S. MOP SINK F.D. FLOOR DRAIN S.S. SCULLERY SINK H.D. HUB DRAIN F.E.S. FABRICATED ECONOMY SINK F.F.D. FUNNEL FLOOR DRAIN H.S.. HAND SINK K.F.D. KITCHEN FLOOR DRAIN U.B.S. UNDER BAR SINK R.F,D. RESTROOM FLOOR DRAIN U.B.H.S. UNDER BAR HAND SINK E.M. ELECTRICAL METER I.C.C. ICE CREAM CABINET G.M. GAS METER WATER CALCULATIONS - HABIT BURGER PLUMBING FIXTURE QTY. WATER SUPPLY F.U. EACH WATER SUPPLY F.U. TOTAL LAVATORY 2 1 2 WATER CLOSET (FLUSH VALVE) 3 8 24 URINAL 1 5 5 3 -COMP SINK 1 4 4 MOP BASIN 1 3 3 1 BOWL PREP SINK 1 1.5 1.5 HAND SINK 2 1.5 3 WATER TO SODA/ICE 1 3 3 DUMP SINK 1 2 2 GAS PIPING SIZED PER TABLE 1216.2(1) OF THE 2012 UNIFORM PLUMBING CODE TOTAL LENGTH FROM METER TO PATIO HEATER = 300' TOTAL 47.5 (BASED ON TABLE A2.1,2012 UNIFORM PLUMBING CODE) 11/2" GAS LINE CALC. EQUIPMENT TAG MBH DISTANCE TO METER GAS LINE CONNECTION SIZE RTU -1 180 124' 3/4" RTU -2 224 172' 1-1/4" MAU-1 226 146' 1-1/4" FRYER (3 @ 80) 240 198' 3/4" CHAR BROILER 105 197' 3/4" GRIDDLE (2 @ 90) 180 220' 3/4" PATIO HEATER (2 @ 50) 100 249' 1/2" WATER HEATER 120 144' 11/4" TOTAL MBH 1375 GAS PIPING SIZED PER TABLE 1216.2(1) OF THE 2012 UNIFORM PLUMBING CODE TOTAL LENGTH FROM METER TO PATIO HEATER = 300' ATERhMS SUP Y KEYED NOTES O ( NEW GAS WATER HEATER. SEE PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR ADDITIONAL INFORMATION. SET WATER TEMP. FOR 125'F. MAX. 2O 1/2" COLD WATER AND 1/2" HOT WATER LINE DOWN INSIDE WALL TO HAND SINK. O3 3/4" COLD AND HOT WATER LINE DOWN INSIDE WALL TO THREE COMPARTMENT SINK FAUCET AND 1/2" COLD AND HOT WATER LINES DOWN TO BELOW SINK FOR CHEMICAL FEED SYSTEM. O4 PROVIDE 1/2" COLD WATER CONNECTION FROM WATER FILTER TO ICE MAKER WITH BIN. O 1/2" COLD AND HOT WATER DOWN INSIDE WALL TO MOP SINK. O 1/2" COLD AND HOT WATER DOWN INSIDE WALL TO PREP SINK. O 1/2" FILTERED WATER DOWN IN WALL TO CARBONATOR. O 2 1/2" GAS PIPE UP THRU ROOF. SEE MEP100 FOR CONTINUATION. O9 1/2" FILTERED WATER LINE DOWN INSIDE WALL AND BASE CABINET SPACE TO ICE MAKER AND TEA BREWER. CONTRACTOR TO PROVIDE APPROVED BACKFLOW PROTECTION DEVICE. SEE PLUMBING FIXTURE SCHEDULE. FOR ADDITIONAL INFORMATION. 10 1" COLD WATER INSIDE WALL TO WATER CLOSET. 11 1/2" COLD WATER AND 1/2" HOT WATER LINE DOWN INSIDE WALL TO LAVATORY. NEW THERMOSTATIC MIXING VALVE (TMV-1) SUPPLIED AND INSTALLED BY PLUMBING 12 CONTRACTOR BELOW SINK AND LAVATORIES AT LOCATIONS INDICTED. SET WATER TEMPERATURE FOR 1057 MAXIMUM. CIRCULATING HOT WATER TO RUN TO THE HOT WATER INLET OF TMV — SEE RISER DIAGRAM ON SHEET P400. SEE DETAIL 9/P410 FOR ADDITIONAL INFORMATION. 13 ROUTE 3/4" COLD WATER DOWN IN WALL TO WATER FILTER. FIELD VERIFY LOCATION. 14 3/4" COLD WATER INSIDE WALL TO URINAL. 15 ROUTE 1/2- COLD WATER PIPING BELOW FLOOR FROM TRAP PRIMER TO FLOOR DRAINS. FIELD VERIFY LOCATION. 16 CONNECT TO LANDLORD VALVED AND CAPPED 1 1/2" COLD WATER LINE IN CRAWL SPACE. FIELD VERIFY EXACT LOCATION PRIOR TO INSTALLATION OF SUB METER AND REMOTE READER. TENANT'S CONTRACTOR TO FURNISH AND INSTALL A SUB WATER METER W/REMOTE READER IN CEILING SPACE. COORDINATE LOCATION OF REMOTE READER WITH LANDLORD. 17 NEW 1 1/2" GAS DOWN TO GAS HEADER FOR COOKING EQUIPMENT. 18 PROVIDE MANUAL EMERGENCY GAS SHUT—OFF VALVE IN 2" GAS RISER DOWN TO COOKING EQUIPMENT. REFER TO GAS RISER DIAGRAM ON SHEET P400 FOR RISER FOR INFORMATION. PROVIDE AUTOMATIC EMERGENCY GAS SHUT—OFF VALVE IN 2" GAS RISER AND TIE INTO 19 ANSUL FIRE SUPPRESSION SYSTEM. REFER TO SHEET MECHANICAL HOOD DRAWINGS AND GAS RISER DIAGRAM ON SHEET P400 FOR INFORMATION. 20 1 1/4" MANIFOLD CONNECTION TO FRYERS, 3 FRYERS @ 80 CFH EACH. 21 3/4" GAS LINE TO GRIDDLE (90.0 MBH). TYPICAL OF 2 22 NEW HOT WATER RECIRCULATION WATER PUMP WITH INTEGRATED TIMER AND AQUASTAT. SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. SET TIMER FOR ON AT 8:30 A.M. AND OFF AT 11:00 P.M. DAILY. 23 NEW 1/2"CW WITH VALVE UP TO MAU-1 ON ROOF. COORDINATE LOCATION WITH MECHANICAL CONTRACTOR AND OWNERS REPRESENTATIVE. 24 3/4" GAS LINE DOWN TO CHAR ROCK BROILER (105 MBH). 25 NEW 1 1/2" GAS DOWN TO GAS HEADER FOR COOKING EQUIPMENT. 26 NEW 3/4"HW UP TO ITEM #78 ON ROOF. COORDINATE. LOCATION WITH MECHANICAL CONTRACTOR AND OWNERS REPRESENTATIVE. 27 NG STUB UP. CONTRACTOR TO FURNISH AND INSTALL PATIO HEATER (50 MBH). PROVIDE DIRT LEG AND SHUTOFF VALVE WITH LOCKABLE HANDLE IN ACCORDANCE WITH LOCAL CODE. 28 NG DROP TO BELOW FLOOR INTO CRAWL SPACE WITH GAS VALVE IN CEILING (DRESSER STYLE 175 OR EQUAL), SEE GAS RISER DIAGRAM ON SHEET P400. 29 1 1/4" GAS PIPING DROP TO BELOW GRADE. SEE GAS RISER DIAGRAM ON SHEET P400. 30 1 1/4" GAS PIPE DOWN TO WATER HEATER (120 MBH). 31 NEW 1-1/2" WATER METER. LOCATE IN ACCESSIBLE LOCATION ABOVE CEILING. COORDINATE EXACT LOCATION OF SUB METER AND REMOTE READER WITH LANDLORD. 32 NEW 1-1/2" BACKFLOW PREVENTOR. SEE PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR ADDITIONAL INFORMATION. DRAIN INTO FLOOR DRAIN. FIELD VERIFY EXACT LOCATION. NOTE: 1. REFER TO RISER DIAGRAM ON SHEET P400 FOR PIPE SIZES. 2. REFER TO PLUMBING FIXTURE SCHEDULE ON SHEET P100 FOR KEYED NOTES O AND O . 3. REFER TO SHEET FOOD SERVICE DRAWINGS FOR PLUMBING ROUGH—IN INFORMATION. LINE TYPES: -ws-ws-ws-ws- REVIEWED FOR BODE CQMPLIAPdCE r' APPROVED APR 13 2016 City of TukvAla BUILDING DIVISION NATURAL GAS PIPING COLD WATER PIPING FILTERED COLD WATER PIPING 110 DEG HOT WATER PIPING 125 DEG HOT WATER PIPING HOT WATER RETURN PIPING UNDER SLAB WATER PIPING RECD 1v,,,=.p CITY O�j: T UKWILA VIAR 17 2016 PERMIT CENTER KEYED NOTES �1 1 1/2" DOWN TO WATER HEATER. �2 1 1/2" FROM WATER HEATER. O 1 /2"FW DOWN TO CARBONATOR. O CONNECT TO EXISTING WATER MAIN IN CRAWL SPACE. COORDINATE EXACT LOCATION IN FIELD. O5 1/2" COLD AND 1/2" HOT WATER DOWN TO CHEMICAL FEED SYSTEM. O6 1/2" COLD WATER BELOW FLOOR TO FLOOR DRAIN. O7 THERMOSTATIC MIXING VALVE IMV -1) BELOW FIXTURE. SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION. O EXISTING 1 1 /2"CW INSTALLED BY LANDLORD. O 1/2" COLD WATER BELOW FLOOR FROM TRAP PRIMER. 10 EXTEND AND CONNECT NEW SANITARY PIPING TO EXISTING 4" SANITARY SEWER INSTALLED BY LANDLORD. VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FIELD. 11 NEW 3" VENT PIPING UP, 4" VENT THRU ROOF. 12 EXTEND AND CONNECT NEW GREASE WASTE PIPING TO EXISTING 4" GREASE WASTE. VERIFY EXACT LOCATION, SIZE DEPTH, DIRECTION OF FLOW AND PIPE MATERIAL OUT IN THE FIELD. 13 LANDLORD INSTALLED 3" GAS PIPE TO LANDLORD INSTALLED GAS METER AT METER BANK. CONTRACTOR SHALL VERIFY EXACT GAS METER LOCATION, VERIFY METER HAS THE CAPACITY TO DELIVER A 945 MBH TOTAL DEMAND LOAD. 14 NEW 3/4"HW UP TO ITEM #78 ON ROOF. COORDINATE LOCATION WITH MECHANICAL CONTRACTOR AND OWNERS REPRESENTATIVE. 15 SEE DETAIL 12/P410 FOR ROUTING OF VENT PIPING IN HALF WALL. 16 1 1/2" TO AND FROM RPZ BACKFLOW PREVENTER. 1 /2„ 1/2's 00 r' .00, 0 `) 1 IAV /00 doo '� 1.0000, 00 1 /2„1 7 wC 1 1/2 1 1/4" 1" �� 1 1/2" � U Y I 1 �� C `� TP ` 1/2„ ` /� 6 0000`WC). 1/2" \ ` 1/29# 1/2's 1 1/2" LAV Q 7 3 B P— /%'00 � ./ � 1 1' i\>l 1 /2 CW UP TO 0 MAU-1 ON ROOF . 3/4" 1/2" �� op %b 3/4 1 1/2 to 40' � 1 1/219 ...00"t / • . �' 1 2 ' / IS r/ '' 1 1 14 /2" / " 1 1 2» / 10 .00. 0,00, ; ` 1/2„ I V• y1 BFP-1 1/2„ /..�'' 1/2„ �� / 1„ / 45 1/2p' �`� �� 1 1/4" 1/29' / � `� `� 16 •� /. /�. / \ TP � �. // 3/4„ 6.5 `.� ' �/ 1 1/4" I FCO aEE-2_/ 1/2�� 1„ 3/4„ i 14 ��/ ��. 1„ 12 1 I 1/2„ 5 3/4" � . 0-00 1 �•�•_ /� 3/4„ Ii 3 1 „ 1/2'p ` . 3/4„ 1 /2'� 6 1 /2 �j," ' / 6 1" 1 1 1 7 1 /2"CW FROM 7 ��'.� 1/2„ 81 1'Z-1 /2 TRAP PRIMER 411,000 ' �' 1 1/2" CONTRACTOR FURNISHED AND INSTALLED SUB—WATER METER WITH REMOTE READER, COORDINATED WITH LANDLORD FLOOR PENETRATION (TYPICAL) �,.,,�TOR TO ENSURE ALL UNDERGROUND WATER PIPING TO BE PROPERLY INSULATED I IN Wlflli�j F, REDUCER MIN. 60 PSI RATED LINE SHUT—OFF VALVE SEE GAS RISER DIAGRAM FOR CONTINUATION I II '`. �I. POUNDS TO INCHES LINE REGULATOR ADJUSTABLE UP TO AT LEAST 10" W.C., INLET RATED AT MIN. 60 PSIG NN I I NN -4- GAS GAS METER WITH NEW�.N SERVICE AT METER `�.I„'i BANK 1375 TOTAL MBH I� • I I I NEW GAS SERVICE @ 2 PSI PArb-n i RL CCAS RISER DIA WwAM NOM ��1 1/2" 16 PATIO HEATER 50 MBH i PATIO HEATER 50 MBH (50 MBH) DROP SANITARY PIPING BELOW STRUCTURAL BEAM 1 1 /2"SS 1 /2"CW FROM TRAP PRIMER GAS SHUT—OFF VALVE (DRESSER STYLE 175 OR EQUAL) IN CEILING SPACE IN ACCESSIBLE LOCATION DROP TO BELOW GRADE �. ! 4" VTRloot TO EXISTING - LIFT STATION FCO. 3"—/ UR TRAP PPIAAFR 3"G @ 7" W.C. (1375 MBH) ON ROOF 2-1/2" @ 7" W.C. (630 MBH) ON ROOF 1/4" @ 7" W.C. (100 MBH) PIPING ROUTED/ J IN CRAWL SPACE\ .0010,1 1/2" @ 7„ W.C. to (224 MBH) RTU -2 Ir0000pON ROOF 224 MBH 2"G @ 7" W.C. (525 MBH) 1 1/2"G @ 7” W.C. (345 MBH) 1"G TO GRIDDLE (90 MBH) 1 ,G TO GRIDDLE (90 MBH) 1"G TO CHAR ROCK BROILER (105 MBH) a� 1 1/4" G TO MANIFOLD FOR 3 FRYERS (240 MBH) ELEVATION: 25-1/2" BELOW SUBFLOOR 4—NN_ ! �Y FLOOR PENETRATION � (TYPICAL) 3" @ 7" W.C. (1375 MBH) ON ROOF (226 MBH) ON ROOF MAU-1 226 MBH EXISTING 4"SS ELEVATION: 19" — BELOW SUBFLOOR li 1 /2"CW FROM TRAP PRIMER 2 1/2" @ 7" W.C. (745 MBH) ON ROOF c1� BUILD ROOF PENETRATION �%`2 1/2" @ 7" W.C. / (745 MBH) 1 1/4" @ 7" W.C. (100 MBH) 2-1/2" @ 7" W.C. (625 MBH) TO EXISTING 'pj I I 1/4"G @ 7" W.C. (120 MBH) WATER HEATER 120 MBH RECEIVED ,EgC I �� E CITYa' �~�i�WILA 1000, AUTOMATIC AND MANUAL EMERGENCY Om SHUT—OFF VALVES CONNECTED TO ANSUL MAR 17 2016 SYSTEM. FURNISHED BY F.S.E. AS PART % OF HOOD AND INSTALLED BY PLUMBER PERMIT CENTER I kl�_l 1/4"G @ 7" W.0 (120 MBH) M TOTAL DEVELOPED LENGTH FROM METER TO PATIO HEATER = 300' ZZZA 18" (457mm) 34 1/2" (86mm) DIA. TOP CLEARANCE REFLECTOR 24" (61Omm) SIDE CLEARANCE Lmm RADIANT EMITTER GRID PILOT LIGHTING HOLE 12" KEEP GREASY (305mm) HANDS OFF HEATER HEAD 100% SAFETY SHUT— OFF CONTROL HEATER HEAD BASE i SLIP COLLAR 3" DIA STEEL POST i itsli (282 mm) 93" (2362mm) 2 (213 4" 4mm) NEC C1 k%2 24V 1 raMlotmei•20YA (SupPRIA by . . Ieutailw) , 12� 2a v. It any or Tho odglnat Wire as supplie d , `f SWklf wllcb with the appliance muni !M repl"j". (,�' it mustpe replaced witb wiring mats• On�mntr del having o temperature rating ohrd- ®I Supplied) tease 105 depreca Centigrade. 1 ' EIlCtrica{ HapMup PAmnO HEATER. SCAM NOW1 ITEMPERED WA 3/8 COMPRESSION CONNECTIONS - 1/2" INTERNAL PIPING ii GAS SHUT—OFF VALVE UNDERGROUND ii VAULT BOX �I GAS SERVICE PIPE CONNECT TO SINK FAUCET COLD WATER TEMPERING MIXING VALVE U 3/8" COMPRESSION TEE HOT WATER STUB OUT IN WALL. 3/8" CHROME TUBING TYP. 1 /2" COLD AND HOT WATER OLD WATER STOP SINK /—CONNECT TO LAVATORY METERING TEMPERED WATERFAUCET — 3/8" COMPRESSION CONNECTIONS\ COLD WATER TEMPERING MIXING VALVE HOT WATER STUB OUT IN WALL. 3/8" CHROME TUBING TYP. 1/2" COLD AND HOT WATER STOP VAL v LAVATORY WATER DRAIN PIPE SHALL BE CUT AT AN INSTALL FLUSHW/ ANGLE AS SHOWN. TYPICAL FINISHED FLOOR INDIRECT DRAIN FROM EQUIPMENT. AIR GAP -r FIN_ FI OOR METAL GRATE TO BE 1/2 WITH 1/2 LEFT OPEN. NOTE: 1. ALL FLOOR SINKS MUST BE FLUSH WITH TILE FLOOR AS SHOWN ABOVE 11; 11q 11111 - ,av CLEANOUT AND ACCESS CLEANOUT TO BE LOCATED COVER. TOP OF COVER IN NON CARPETED AREA TO BE FLUSH w/ TOP WHEN POSSIBLE. OF FLOOR FINISHED FLOOR •. •, e..•d : .. •. I-1 I 1/8 BEND 1/8 BEND IF CLEANOUT OCCURS AT END OF LINE --n ✓ WASTE LINE, LENGTH 19, Kole] MINIMUM 22 GAUGE METAL STRAP MATERIAL INSTALLED WITHIN THE TOP 1/3 OF THE HEATER AND BOTTOM 1/3 OF THE HEATER. DRILL PILOTS ON CENTER LINE OF STUD, INSERT SCREWS THROUGH PUNCHED HOLES IN STRAP. USE MINIMUM 1/4" SCREWS WITH MINIMUM 1 -1/2 - PENETRATION. -1 /2" PENETRATION. USE WASHERS---., BETWEEN SCREWS AND STRAP. THE LOWER STRAP MUST BE A MINIMUM OF 4" ABOVE THE CONTROL UNIT. WALL STUD 4" MINIMUM CONTROL UNIT —1/2" COLD WATER OUTLET TO CARBONATOR 1/2" OUTLET TO ICE TEA ® SODA BAG—N—BOX MAKER &ICE MAKERS— WATTS 009 BACKFLOW PREVENTER � -. DRAIN WITH AIR GAP 3/4" COLD WATER INLET EVERPURE HIGH FLOW CSR TRIPLE — 7FC SYSTEM / PART #EV9329-73 — OWNER SUPPLIED "h 0 IN't4,, .011911%141m� ,$ CHROME WAL AND SCREW MAY EXTEND AS WASTE OR VENT PLUGGED TEE w/ CLEANOUT FLOOR LINE 5LB. LEAD FLASHING SHALL BE FORMED TO CHIPPED CONCRETE WITH A POSITIVE SLOPE TO CLAMP DEVICE. PROVIDE NON— SHRINK SPOUT UNDER LEAD FLASHING AS REQUIRED TO FACILITATE POSITIVE SLOPE (ANY FLASHING MATERIALS OTHER THAN LEAD IS UNACCEPTABLE. MINIMUM WIDTH OF FLASHING SHALL BE 24"). ADJUSTABLE FINISH FLOOR STRAINER SLOPE TO DRAIN 1/2 CW TO TRAP PRIMER a o CAST IRON FLOOR DRAIN CORE DRILL 10% AND 4"0 HOLES THREADED OR CAULK OUTLET 0 UTL=T NOTE: THE GENERAL CONTRACTDR SHALL PROVIDE A ONE PIECE WATER PROOF MEMBRANE FLOOR AND BASE IN THE TOILET ROOM(S). FLOO PRIMER SCAL B NOE PROVIDE EXTENSIONS AS REQUIRED SHEET LEAD FLASHING MOP—IN WITH ROOFING MATERIAL 12" ROOFING--\ (MIN.) SLEEVE ROOF CONSTRUCTION AS REQUIRED NOTE: CONTRACTOR SHALL PROVIDE EXTENSION AS REQUIRED ON VENT PIPE AS TO ENSURE VENT PIPE IS HIGHER THAN PARAPET VENT THRC SCALS NONE TURN LEAD DOWN INTO STACK 2" VENT ROUTED INTO CEILING SPACE 1 1/2" VENT FROM FLOOR DRAIN) HAND SINK (#37) HALF LL ROOF STRUCTURE INCREASE AS REQUIRED I HANGER RG PIPE IINSULATIOf WHERE RE UNISTRUT CHANNEL 1�4'LL�l�1►1t��1:�7►� PROVIDE A SECTION OF HIGH COMPRESSION STRENGTH INSULATION AT EACH HANGER POINT. INSULATION MAY BE HALF ROUND OR FULL ROUND AND EXTENDED 2" BEYOND GALVANIZED SHIELD O EACH WAY SHEET SHIELD (12" LONG) NOTES: 1. ATTACH SUPPORTS FOR ALL PIPING SUSPENDED FROM THE STEEL STRUCTURE TO THE TOP CHORD OF JOISTS OR BEAMS. 2. PROVIDE COPPER OR PLASTIC COATED HANGERS FOR NON—INSULATED COPPER PIPE. TOP OF HALF WALL 1 1/2" VENT FROM 2"V FLOOR DRAIN MINIMUM HEIGHT N FOR VENT PIPING —OX INSTALLATION FLOOD RIM OF SINK 1 1/2" VENT FROM HAND SINK TOP OF WORK SURFACE BEAM BEAM CONNECT CLEVIS HANGER OVERSIZED FOR INSULATION WITH 18" ROLLE SLEEVE FOR SUPPORT 180' - HANGER SPACING AND ROD SIZE PIPE LL: ROD CD GATE VALVE SIZE 1/2#' 70 STRAINER 3, 4" Z VERTICAL PUMP OR AIR RELEASE L21 VALVE 3/81r Q —HOT WATER RECIRCULATION PUMP — 7, T SEE PLUMBING FIXTURE SCHEDULE FOR ADDITIONAL INFORMATION 11 /4" — SWING CHECK VALVE �-' SWING CHECK VALVE 9' —�— PUMP PRIMING HOSE GROUND JOINT UNION, (DIELECTRIC) BIBB T&P RELIEF VALVE TO BE PIPED EXPANSION TANK ON COLD WATER SUPPLY FULL SIZE TO FLOOR DRAIN OR 1/211 FLOOR SINK. TERMINATE WITH CODE APPROVED AIR GAP n 31/2" /2" 13' 1/2's 4" PIPING SHALL BE ROUTED TO 5/8" WATER HEATER IN A MANNER WATER WHICH FACILITATES FUTURE HEATER REMOVAL/REPLACEMENT OF THE WATER HEATER. Cd IP WATER HEATER TO SET ON CONCRETE PAD — SEE ;:.4 :;. •:• ; :.: ;:.. ; ARCHITECTURAL DRAWINGS • ;�'• FOR DETAILS I HANGER RG PIPE IINSULATIOf WHERE RE UNISTRUT CHANNEL 1�4'LL�l�1►1t��1:�7►� PROVIDE A SECTION OF HIGH COMPRESSION STRENGTH INSULATION AT EACH HANGER POINT. INSULATION MAY BE HALF ROUND OR FULL ROUND AND EXTENDED 2" BEYOND GALVANIZED SHIELD O EACH WAY SHEET SHIELD (12" LONG) NOTES: 1. ATTACH SUPPORTS FOR ALL PIPING SUSPENDED FROM THE STEEL STRUCTURE TO THE TOP CHORD OF JOISTS OR BEAMS. 2. PROVIDE COPPER OR PLASTIC COATED HANGERS FOR NON—INSULATED COPPER PIPE. TOP OF HALF WALL 1 1/2" VENT FROM 2"V FLOOR DRAIN MINIMUM HEIGHT N FOR VENT PIPING —OX INSTALLATION FLOOD RIM OF SINK 1 1/2" VENT FROM HAND SINK TOP OF WORK SURFACE BEAM BEAM CONNECT CLEVIS HANGER OVERSIZED FOR INSULATION WITH 18" ROLLE SLEEVE FOR SUPPORT 180' - HANGER SPACING AND ROD SIZE PIPE MAX ROD SIZE SPAN SIZE 1/2#' 70 3/8" 3, 4" 7, 3/81r 1 7, 3/8" 11 /4" 7' 3/8" 1 1/2" 9' 3/8" 2" 10' 3/8" 1/2" 1 2' 1/211 3 /211 31/2" /2" 13' 1/2's 4" 14' 5/8" UIRED RE!/kE D FOR CODE COMPLIANCE APPROVED APR 13 2016 City of TukvAla BUILDING DIVISION CITY Or,- yUKWI ..A NEAR 17 2016 PERMIT CENTER FFn..... .. z . • Interceptor Solids Separator Options �£ w ,hug Top View �aa.� cmj 3URFAC£ Bottom View Side View Isom [3.8 cm] i Material: Diamond Plate Aluminum l STIFFENERS The FTCA-22 Top Cover takes the place of the 22" Diameter Solid Top Cover and is compatible with the TZ -160, Standard Adapter Top Cover, ECA -29 and ECA -18. It provides a durable, non -slip, diamond plate surface (not shown in drawing) for installation in high traffic areas such as a kitchen floor. *Trapzilla units are not rated for vehicle traffic regardless of what top is on the unit. 02014 Thermaco, Inc. - All rights reserved - Patented!Patents Pending - Specifications subject to change without notice Thermaco, Inc. • PO Box 2548 - Asheboro, NC 27204-2548 - Phone: (336) 629-4651 • www.trapzilia.com Tra zilla R Grease Interceptors ill lilt 1 F . 3 ta.t?..,.. a,..«. cj,a,zil TOP VIEW 73.0 in (185.4 cm] TZ -1826 Specifications FEATURES: • Offers a flat grease separation curve. • Constructed of corrosion resistant materials suitable for installation in virtually any location. • Compact footprint. • Includes dual 0-18" extension collars for in -ground installation. SIDE VIEW MAXIMUM COLLAR EXTENSION END VIEW COLLAR FLUSH (TRIMMED) TECHNICAL DATA Materials: Rotationally Molded Polyethylene 31 UPC Maximum Inlet Flow Rating: 100 GPM (6,31 11s) C S C Total Liquid Volume (water only): 274 Gallons (1,037 L) Grease Retention Capacity (ASME certified): 1,82.6 Pounds (828 Kg) - uran++x+,v^xc 248.77 Gallons (941 t-) Solids Rolention Capacity (estimated): 74 gallons (280 L) Inlet/OutIEt Diameter: 4" (102 mm) @2015 Thermaco, Inc. • All rights reservod • Patonted/Patents Pending - Specifications subject to chango without notice 11, Thermaco, Inc. • PO Box 2548 - Asheboro, NC 27204-2548 - (336) 629-4651 - www.trapzilia.coni Suggested Minimum Footprint Dimensions The Trapzilla" requires 6" (15.24 cm) of clear- ance all the way around the lid from walls or other structures to allow for servicing. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown. Make piping connections with rubber "No Hub" connectors. Keep outlet piping as straight as pos- sible. Use only "sweep" connections. Install vent on outlet piping. If installing in conjunction with other Trapzilla products, include cleanout port NOTE: Drawing for reference only. Equip - DON'T ' ' ' Install "P" trap on outlet connectioh Reduce pipe size on outlet piping, ment must be installed in compliance with of tank. (Note: the unit already has all applicable laws, regulations and codes, an internal gas trap), including plumbing codes. Installationshould be performed by a qualified plumber. Job Specification: Grease and oils separator(s) shall be Thermaco Trapzilla hydromechanical grease/oil interceptor system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install — Thermaco Trapzilla Madel No. TZ -1826, linear low-density rotationally molded polyethylene grease and oil separator(s) for below or above -ground installation, shall be PDI -G 101 and ASME A112.14.3 -rated at 100 GPM (6.31 I/s), 1826 pounds (828 Kg) of grease storage capacity with a flat grease separation efficiency curve, crush -resistant cylindrical walls, two fully removable covers for grease and solids removal, integral non - floatation anchor ring for in -ground installation, integral horizontal baffle, laminar inlet flow diverter, integral vessel Vent, separate storage compartments for grease and solids, and including as an integral part of the unit an integral gas trap and a fully removable polyethylene self -positioning keyed cover equipped with sealed thread fasteners. Includes dual -entry extension collar assembly, linear low-density rotationally molded polyethylene for field adjust - ability to optimal installation depth, isD2015 Thermaco, Inc. - All rights reserved - Patented/Patents Pending • Specifications subject to change without notice Thermaco, Inc. - Po Box 2548 - Asheboro, NC 27204-2548 • (336) 629-4651 - www.trapzilla.com WED FOR CODE COMPLIANCE APPROVED APR 13 2016 City of TukMIa BUILDING DIVISION REC,"&-- IVE0 CITY OF WKWILA MAR 17 2016 PERMIT CENTER 10 in [25.4 cm] IIEARANCE FROM ---- --18.0in TOP OF TANS; REQIIIRF.D FOR IID REMOVAL f.......... 18.01" [45.7 cm] MAX EXTENSION 2 in VENT l r _ 13.1 In 14.1 (n 133.3 crrr] [359 cm] M11 �L.FT OUTLET 4 In 4 in Pi PF. SIZE _ —PIPE SIZE 54.3 in [137.8 on] 41.1 m 40.1 [104.5 cm] [101.9 an] c SIDE VIEW MAXIMUM COLLAR EXTENSION END VIEW COLLAR FLUSH (TRIMMED) TECHNICAL DATA Materials: Rotationally Molded Polyethylene 31 UPC Maximum Inlet Flow Rating: 100 GPM (6,31 11s) C S C Total Liquid Volume (water only): 274 Gallons (1,037 L) Grease Retention Capacity (ASME certified): 1,82.6 Pounds (828 Kg) - uran++x+,v^xc 248.77 Gallons (941 t-) Solids Rolention Capacity (estimated): 74 gallons (280 L) Inlet/OutIEt Diameter: 4" (102 mm) @2015 Thermaco, Inc. • All rights reservod • Patonted/Patents Pending - Specifications subject to chango without notice 11, Thermaco, Inc. • PO Box 2548 - Asheboro, NC 27204-2548 - (336) 629-4651 - www.trapzilia.coni Suggested Minimum Footprint Dimensions The Trapzilla" requires 6" (15.24 cm) of clear- ance all the way around the lid from walls or other structures to allow for servicing. READ instruction manual included with system before doing anything. Install unit allowing for the minimum clearances shown. Make piping connections with rubber "No Hub" connectors. Keep outlet piping as straight as pos- sible. Use only "sweep" connections. Install vent on outlet piping. If installing in conjunction with other Trapzilla products, include cleanout port NOTE: Drawing for reference only. Equip - DON'T ' ' ' Install "P" trap on outlet connectioh Reduce pipe size on outlet piping, ment must be installed in compliance with of tank. (Note: the unit already has all applicable laws, regulations and codes, an internal gas trap), including plumbing codes. Installationshould be performed by a qualified plumber. Job Specification: Grease and oils separator(s) shall be Thermaco Trapzilla hydromechanical grease/oil interceptor system(s) as manufactured by Thermaco, Inc., Asheboro, North Carolina as noted on plans. Separator Specifications: Furnish and install — Thermaco Trapzilla Madel No. TZ -1826, linear low-density rotationally molded polyethylene grease and oil separator(s) for below or above -ground installation, shall be PDI -G 101 and ASME A112.14.3 -rated at 100 GPM (6.31 I/s), 1826 pounds (828 Kg) of grease storage capacity with a flat grease separation efficiency curve, crush -resistant cylindrical walls, two fully removable covers for grease and solids removal, integral non - floatation anchor ring for in -ground installation, integral horizontal baffle, laminar inlet flow diverter, integral vessel Vent, separate storage compartments for grease and solids, and including as an integral part of the unit an integral gas trap and a fully removable polyethylene self -positioning keyed cover equipped with sealed thread fasteners. Includes dual -entry extension collar assembly, linear low-density rotationally molded polyethylene for field adjust - ability to optimal installation depth, isD2015 Thermaco, Inc. - All rights reserved - Patented/Patents Pending • Specifications subject to change without notice Thermaco, Inc. - Po Box 2548 - Asheboro, NC 27204-2548 • (336) 629-4651 - www.trapzilla.com WED FOR CODE COMPLIANCE APPROVED APR 13 2016 City of TukMIa BUILDING DIVISION REC,"&-- IVE0 CITY OF WKWILA MAR 17 2016 PERMIT CENTER