The URL can be used to link to this page

Home My WebLink AboutPermit PG17-0014 - SYKART INDOOR RACING - WATER HEATER, BATHROOM, WATER LINES, GREASE TRAPSYKART INDOOR RACING 17450 WEST VALLEY HWY PGI 7-0014 Parcel No: Address: City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Inspection Request Line: 206-438-9350 Web site: http://www.TukwilaWA.gov PLUMBING/GAS PIPING PERMIT 2523049020 17450 W VALLEY HWY Project Name: SYKART INDOOR RACING Permit Number: PG17-0014 Issue Date: 2/24/2017 Permit Expires On: 8/23/2017 Owner: Name: Address: Contact Person: Name: Address: Contractor: Name: Address: License No: Lender: Name: Address: ALCO INVESTMENT COMPANY PO BOX 3546 , SEATTLE, WA, 98124 LUKE VASQUEZ 17450 WEST VALLEY HWY , TUKWILA, WA, 98188 AFFIDAVIT - TODD BAKER 1 II Phone: (206) 226-3771 Phone: Expiration Date: DESCRIPTION OF WORK: REPLACE WATER HEATER, ADD PRIVATE BATHROOM. NEW WATER LINES AND DRAINAGE FOR KITCHEN INCLUDES INSTALLATION OF A GREASE TRAP. Valuation of Work: $5,000.00 Water District: RENTON Sewer District: RENTON Fees Collected: $363.99 Current Codes adopted by the City of Tukwila: International Building Code Edition: International Residential Code Edition: International Mechanical Code Edition: Uniform Plumbing Code Edition: International Fuel Gas Code: 2015 2015 2015 2015 2015 National Electrical Code: WA Cities Electrical Code: WAC 296-46B: WA State Energy Code: 2014 2014 2014 2015 Permit Center Authorized Signature: - • '04 Date:) ---;c1,14,4 I hearby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances governing this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local laws regulating construction or the performance of work. I am authorized to sign and obtain this development permit and agree to the conditions attached to this permit. Signature: Print Name: 1277/3/c/1-- Date: ---,)t7/—/ This permit shall become null and void if the work is not commenced within 180 days for the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. PERMIT CONDITIONS: 1: ***PLUMBING/GAS PIPING PERMIT CONDITIONS*** 2: No changes shall be made to applicable plans and specifications unless prior approval is obtained from the Tukwila Building Division. 3: All permits, inspection records and applicable plans shall be maintained at the job and available to the plumbing inspector. 4: All plumbing and gas piping systems shall be installed in compliance with the Uniform Plumbing Code and the Fuel Gas Code. 5: No portion of any plumbing system or gas piping shall be concealed until inspected and approved. 6: All plumbing and gas piping systems shall be tested and approved as required by the Plumbing Code and Fuel Gas Code. Tests shall be conducted in the presence of the Plumbing Inspector. It shall be the duty of the holder of the permit to make sure that the work will stand the test prescribed before giving notification that the work is ready for inspection. 7: No water, soil, or waste pipe shall be installed or permitted outside of a building or in an exterior wall unless, adequate provision is made to protect such pipe from freezing. All hot and cold water pipes installed outside the conditioned space shall be insulated to minimum R-3. 8: Plastic and copper piping running through framing members to within one (1) inch of the exposed framing shall be protected by steel nail plates not less than 18 guage. 9: Piping through concrete or masonry walls shall not be subject to any load from building construction. No plumbing piping shall be directly embedded in concrete or masonry. 10: All pipes penetrating floor/ceiling assemblies and fire -resistance rated walls or partitions shall be protected in accordance with the requirements of the building code. 11: Piping in the ground shall be laid on a firm bed for its entire length. Trenches shall be backfilled in thin layers to twelve inches above the top of the piping with clean earth, which shall not contain stones, boulders, cinderfill, frozen earth, or construction debris. 12: The issuance of a permit or approval of plans and specifications shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the Plumbing Code or Fuel Gas Code or any other ordinance of the jurisdiction. 13: The applicant agrees that he or she will hire a licensed plumber to perform the work outlined in this permit. 14: All new plumbing fixtures installed in new construction and all remodeling involving replacement of plumbing fixtures in all residential, hotel, motel, school, industrial, commercial use or other occupancies that use significant quantities of water shall comply with Washington States Water Efficiency ad Conservation Standards in accordance with RCW 19.27.170 and the 2006 Uniform Plumbing Code Section 402 of Washington State Amendments 15: grease trap shall be installed and maintained per manufacturer's specifications. PERMIT INSPECTIONS REQUIRED Permit Inspection Line: (206) 438-9350 2000 GAS PIPING FINAL 8004 GROUNDWORK 1900 PLUMBING FINAL 9002 ROUGH -IN GAS PIPING 8005 ROUGH -IN PLUMBING 9001 UNDERGROUND CITY OF TUKW 1 Community Development Department Permit Center 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 http://www.Tukwi IaWA.gov Plumbing/Gas germit No. ((' OD t/ Project No. Date Application Accepted: (/I Date Application .Expires:l i' (For o e use only) PLUMBING / GAS PIPING PERMIT APPLICATION Applications and plans must be complete in order to be accepted for plan review. Applications will not be accepted through the mail or by fax. **Please Print** SITE LOCATION / ��// King Co Assessor's Tax No.: Site Address: / �Y�a (/Gt-<l 1212r q t �• `� j)7_ `� 1 Gc�/�GC Suite Number: Floor: Tenant Name: ..#/,(,174 -yj/oo-T a.e/j (e,* (�L New Tenant: ❑ Yes a'No PROPERTY OWNER Company Name: 4Ct�,. Name: Aka (%/12 �Q Phone:20 , _Zz -3777% Fax: (-(Z.- & /". F!%3 Address: < On // o - 35 1 Zip: City: Gf/ /4..._S City: $A # e e State: 04_ Zip: fg/z / CONTACT PERSON - person receiving all project communication Company Name: 4Ct�,. Name: /ll<e tiet S t. e City: � Stat : (Zip: 8 8, Phone:20 , _Zz -3777% Fax: (-(Z.- & /". F!%3 Address:/7 . 41( Tukwila Business License No.: -0/ 00 ,524/ / Zip: City: Gf/ /4..._S g% g, Phone: z0'6 -Z219-3 L7/ Fax: L/2.5'- Z5-/- 7,y.3 Email: PLUMBING CONTRACTOR INFORMATION Company Name: 4Ct�,. Address:/.. / 9 ` r / /L , l/l/ V�� l�T(/�' City: � Stat : (Zip: 8 8, Phone:20 , _Zz -3777% Fax: (-(Z.- & /". F!%3 Contr Reg No.: - Exp Date: Tukwila Business License No.: -0/ 00 ,524/ / Valuation of Project (contractor's bid price): $ 400. 00 Scope of Work (please pr vide detailed information): jiU� %2� QGCGC. / tf ckeJ /22:77/7/ .e(L) GliGc ///2(5 rc�� Building Use er Int'I Building Code): Occupancy (per Intl Building Code): Utility Purveyor: Water: H:\Applications\Forms-Applications On Line\2011 Applications\Plumbing Permit Application Revised 8-9-11.docx Revised: August 2011 bh Sewer: 01) ,CPj(7�YP Page 1 of 2 Indicate type of plumbing fixtures and/o piping outlets being installed and the quanti. low: Fixture Type Qty Bathtub or combination bath/shower • Dishwasher, domestic with independent drain Shower, single head trap I l Sinks I Rain water system — per drain (inside building) j Grease interceptor for commercial kitchen (>750 gallon capacity) 1 Each additional medical gas inlets/outlets greater than 5 Atmospheric -type vacuum breakers not included in lawn sprinkler backflow protections (1-5) Fixture Type Qty Bidet Drinking fountain or water cooler (per head) Lavatory Urinal f Water heater and/or vent j Repair or alteration of drainage or vent piping 1 Repair or alteration of water piping and/or water treatment equipment Backflow protective device other than atmospheric - type vacuum breakers 2 inch (51 mm) diameter or smaller Atmospheric -type vacuum breakers not included in lawn sprinkler backflow protections over 5 Fixture Type Qty Clothes washer, domestic Food -waste grinder, commercial Wash fountain Water closet f Industrial waste treatment interceptor, including trap and vent, except for kitchen type grease interceptors j Repair or alteration of drainage or vent piping I Backflow protective device other than atmospheric -type vacuum breakers over 2 inch (51 mm) diameter Gas piping outlets Fixture Type Qty Dental unit, cuspidor Floor drain Receptor, indirect waste Building sewer and each trailer park sewer Each grease trap (connected to not more j than 4 fixtures - <750 gallon capacity l Medical gas piping system serving 1-5 inlets/outlets for a specific gas Each lawn sprinkler system on any one meter including backflow protection devices PERMIT APPLICATION NOTES - Value of Construction — In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject to possible revision by the Permit Center to comply with current fee schedules. Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation. The Building Official may grant one extension of time for an additional period not to exceed 180 days. The extension shall be requested in writing and justifiable cause demonstrated. Section 103.4.3 International Plumbing Code (current edition). I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING OWNER OR Signature - Print ,11 : 1 AGENT: 1 /z" Z Day- Te ///lephone: 2db ` Z Z '377 P41/9 fe/cf7 City State Zip Date: //ov// Mailing Address: /7Z4c7 P.�t ic47 H:\Applications\Forms-Applications On Line\2011 Applications\Plumbing Permit Application Revised 8-9-11.docx Revised: August 2011 bh Page 2 of 2 Cash Register Receipt City of Tukwila DESCRIPTIONS ACCOUNT QUANTITY PAID PermitTRAK $2,343.03 D16-0331 Address: 17450 W VALLEY HWY Apn: 2523049020 $1,315.16 DEVELOPMENT $1,252.75 PERMIT FEE R000.322.100.00.00 0.00 $1,248.25 WASHINGTON STATE SURCHARGE B640.237.114 0.00 $4.50 TECHNOLOGY FEE $62.41 TECHNOLOGY FEE R000.322.900.04.00 0.00 $62.41 M17-0012 Address: 17450 W VALLEY HWY Apn: 2523049020 $663.88 MECHANICAL $638.35 PERMIT ISSUANCE BASE FEE R000.322.100.00.00 0.00 $33.15 PERMIT FEE R000.322.100.00.00 0.00 $477.53 PLAN CHECK FEE R000.322.102.00.00 0.00 $127.67 TECHNOLOGY FEE $25.53 TECHNOLOGY FEE 1 R000.322.900.04.00 0.00 $25.53 PG17-0014 Address: 17450 W VALLEY HWY Apn: 2523049020 $363.99 GAS $82.88 PERMIT FEE R000.322.100.00.00 0.00 $66.30 PLAN CHECK FEE R000.322.103.00.00 0.00 $16.58 PLUMBING $267.11 PERMIT FEE R000.322.100.00.00 0.00 $180.54 PERMIT ISSUANCE BASE FEE R000.322.100.00.00 0.00 $33.15 PLAN CHECK FEE R000.322.103.00.00 0.00 $53.42 TECHNOLOGY FEE $14.00 TECHNOLOGY FEE TOTAL FEES PAID BY RECEIPT: R10573 R000.322.900.04.00 0.00 $14.00 $2,343.03 Date Paid: Tuesday, January 24, 2017 Paid By: SYKART INDOOR RACING CENTER Pay Method: CHECK 5019 Printed: Tuesday, January 24, 2017 4:27 PM 1 of 1 CRSYSTEMS INSPECTION NO. INSPECTION RECORD Retain a copy with permit RI7c.iIf PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Project: nType of Inspe on: Address: V� % iNR,, 760 - ValD !:� 1 � FryteAL Special Instructions: Date Wanted: V 7 -- 1_ (18—p.m. Requester: Phone No: _ 2-64-2 -3771 Approved per applicable codes. Corrections required prior to approval. COMMENTS: s P/ P ' 71 ATV/41l5/)Cs AMi., Inspector: Date: REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be, paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit PO7-oor'f PERMIT N4. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Project: c / Toa`t Type of Inspection: Ci7 fV t S r F ddre s l%SSD tilt Vii, (J Date Calfed: Special Instructions: J Date Wanted: %a.m. Lif^I �_2- �C�./�%/� .L r.'.� Requester: Phone No: Approved per applicable codes. JCorrections required prior to approval. COMMENTS: 4�s pipe FIA-Tc1C-- (04141601 u.r) C1C1- ga)46;12 is ,�� ,� rte, \./(4,( ve_ 1_0 -/ Ca ' o/c c.p/OL REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Project: sKT � r G:L�rprAc:4 Ty f Inspectip n: -LA � 141 bi n% 6,mL Address: Ti.W. tlfEj '11-tay c a t) Date Called: 2 4LC p1 nid,,,l 6-X/-t_irr at-Ao;s Specialnstructions: 0Phone Date Wanted: a.m. Requester: No: G/ -E, — /-tGv' �i�,_ Ls � 7- Approved per applicable codes. corrections required prior to approval. COMMENTS: r•- PLc.eri-r.6 ( Aunt_ — pico -t- -/1 y /1 A) .. Q4 a Elim r'`... 2 4LC p1 nid,,,l 6-X/-t_irr at-Ao;s 66,460rim t A " W'� / Jo `—CpV v r 3, Slfcurer ct1 drzte< lrn/J re,_. G/ -E, — /-tGv' �i�,_ Ls � 7- rr(� S 1CCd at tS ftp lnspeactr: ^ ' n 4.*10Date443mtai_ s( EINS�'�AN FEE R QUPrioRED. rto n�5c tceckomust be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule r spection. L 1/-12-Z,0/ INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 PCQ 17-001 Y Pro'e gType KZ —rT" C �,��0O of Inspection: C� reast �' � Date Called: Special Instruct' s: 1:7q56 � �--C.� � ` ' 'c. t� 4,,Jv \\\/// �'V Date Wanted: �I /z'zo/� a.m. Requester: Cro:►s /—�N\ 51. Phone Q — 3 7 9 ? 7�Dro �n0 Cp proved per applicable pplicable codes. Corrections required prior to approval. ��< _mak-ePpk• - Inspector: ,...8 cry Date: 4, ar, REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 5outhcenter Bdvd., #100, Tukwila: WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Project: • ay '.i/i'" MOteg gfed4/6 Type of Inspection: OVA6O/JD Address: /7$56 w wI-Lry MO/ Date Called: Special Instructions: A -AI Date Wanted: //i$ V7 a.m. p.m. Requester: Phone No: Approved per applicable codes. LJ Corrections required prior to approval. COMMENTS: � r -44:5S PLIC -5/C 64."-- , A RriNSP frau ' Inspector: Date: //6,....)7 REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. INSPECTION NO. INSPECTION RECORD Retain a copy with permit PERMIT N0. ezv/ CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Project: Yi1, ;i ,' ti OobR. R1)& Type of Inspection: 6040 iiJIiRp: Address: 1745 i4J. V410 m -y Date Called: Special Instructions: Y Date Wanted: /l-6 • / 7 a.m. p.m. Requester: Phone No: EiApproved per applicable codes. Corrections required prior to approval. COMMENTS: Inspector: Date: //'10--/ 7 REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 P6..17_00111 Project: $ iND0OR WN& Type of Inspection: Rove --/1 -iN -s P, Ali - Address: 17456 Int VA LEy Date Called: Special Instructions: Date Wanted: iii—/ –/ 7 m� p.m. Requester: Phone No: ❑ Approved per applicable codes. 1J Corrections required prior to approval. COMMENTS: c) f <. -- 5' n// , LJ6// / ( Inspector: Date: "1 –/7 REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be , paid at 6300 Southcenter Blvd.. Suite 100. Catt to schedule reinspection.' INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 Permit Inspection Request Line (206) 438-9350 (206) 431-3670 Project: 5/KA er /,, ACIA/er Tv� e of Inspection: i, 4 - iA) a 1/X46/ WC Address: 1 7460 111/1/A1265-/ / Date Called: Special Instructions: Date Want ed: ��s 7p.m. m. Requester PhoneNo: _ C� 67o�/- Z o& Approved per applicable codes. D Corrections required prior to approval. COMMENTS: Inspector: �l��`7 �" i Date//� REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Btvd., Suite 100. Call to schedule reinspection. INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd.., #100, Tukwila: WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 RIS- 04/Li Project: gYkAp(� � �f�//� j�/ Te h of II./�nsp7e-cytionyam4vw► ] y Address: /74g0 v/ VAu, )i Date Called: Special Instructions: Date Wante d s///7 p.m. Requester: lvk6 Phone No: Ze6.- zzo- 377 / Approved per applicable codes. ElCorrections required prior to approval. COMMENTS: t Jul � 2414.a . 77V S1 U Ar6- A-r— c.rx p 'mild; - i. Th/L&'r A 6 ci S'�di oilErt GIA t$ ?_ 1O RomaLfal Inspector: Actiivt Date:.. REINSPECTION FEE REQUIRED. Prior to next inspection. fee must be paid at 6300 Southcenter Blvd.. Suite 100. Call to schedule reinspection.; BACKFLOW ASSEMBLY TEST REPORT FOX PLUMBING & NESTING 206-767-3311 CUSTOMER/ €ACILITYNNAME' Sykart Indoor 1 cmgccnter;,. G9"Wr,:109WNER NAME K WATER PURVEYOR �? TRENTON PUI NEW CONSTRUCTION ❑Y ®N ASSEMBLY / CUSTOMER ID# PHONE NUMBER ( ) - FAX NUMBER ( ) PURVEYOR CONTACT NAME Mick Holte SERVICE ADDRESS / METER NUMBER 17450 W Valley Hwy CUSTOMER / OWNER / CONTACT MAILING ADDRESS PURVEYOR EMAIL ADDRESS backflow@rentonwa.gov CITY / STATE Tukwila WA ZIP CODE 98188-5511 CITY / STATE ZIP CODE CUSTOMER EMAIL ADDRESS FOR CC chris@junotavern.com 'ASSEMBLY MANUFACTURER P. WATTS`,.. MODEL; LF009t SERIAL NUMBE 15066 RPBTYPES A 1/2' DOWNSTREAM HAZARO TYPE'or PROCESS D SHWASHER ; LOCATION OF ASSEMBLY NE corner of upstairs bar, upper assembly CONFINED SPACE OYES NO INSTALLATION TYPE ® New 0 Existing 0 Replacement PREVIOUS MAKE / MODEL / SIZE / SERIAL NUMBER DETECTOR READ N/A DOH / USC APPROVED ® YES ❑ NO ORIENTATION H CORRECT INSTALLATION ® YES ❑ NO WATER UNE PRESSURE 75 PSIG VALVE POSITIONS PRIOR TO TESTING SOV#1 DON ZOFF SOV#2 DON ZOFF INITIALTESTRESULT T AFTER REPAIRS GLEANING RPBA CHECK VALVE #1 CLOSED TIGHT LEAKED RELIEF VALVE OPENED AT FAILED TO OPEN CHECK VALVE #2 CLOSED TIGHT LEAKED ACTUAL PRESSURE DROP ACROSS CHECK VALVE #1 PASSED TEST CLEAN / REPAIR: 0 see remarks APPROVED AIR GAP 3.9 PSID El 9.3 PSID ®YES ONO ®YES ONO CHECK VALVE #1 CLOSED TIGHT LEAKED RELIEF VALVE OPENED AT FAILED TO OPEN CHECK VALVE #2 CLOSED TIGHT LEAKED ACTUAL PRESSURE DROP ACROSS CHECK VALVE #1 PASSED TEST PSID PSID OYES ONO APPROVED AIR GAP OYES ONO DCVA CHECK VALVE #I CLOSED TIGHT LEAKED CHECK VALVE #2 CLOSED TIGHT LEAKED PASSED TEST CLEAN / REPAIR: 0 see remarks PSID PSID 0 OYES ONO CHECK VALVE #1 CLOSED TIGHT LEAKED CHECK VALVE #2 CLOSED TIGHT LEAKED PSID PSID PASSED TEST OYES ONO REMARKS E. uipment downstream not yet connected at time of testing. VALVE POSTIONS AFTER TESTING SOV#1 DON ZOFF SOV#2 DON ®OFF TESTER NAME^" #�°:" 'Jason A. Moe EAT CERTIFICATION= TEST MAKE Mid -West ,„ UUGE MODEL 845 5.. GAUGE S_E NUMBER 14)a -Q.51,,:17.99;;,;! GAUGE CALIBRATION DATE; 0.1/0312018 REPAIRED BY N/A COMPANY NAME PHONE NUMBER ( ) - FINAL TEST BY N/A BAT CERTIFICATION TEST GAUGE MAKE GAUGE MODEL COMPANY NAME Fox Plumbing PHONE NUMBER (206) 228-1618 SIGNATURE DATE OF FINAL TEST 01/22/2018 (I HEREBY CERTIFY THAT I PERSONALLY INSPECTED AND FIELD-TESTED THE ABOVE BACKFLOW ASSEMBLY USING WAC 246-290-490 APPROVED, USC 10'" Ed'Uon TEST PROCEDURES AND USED DIFFERENTIAL PRESSURE TEST EQUIPMENT MEETING WAC 246-292-034 REQUIREMENTS FOR THE ABOVE TEST RESULTS WHICH ARE TRUE, COMPLETE AND ACCURATE) BACKFLOW ASSEMBLY TEST REPORT FOX PLUMBING & HEATING 206-767-3311 CUSTOMER / FACRITY NAME Sykart Indoor Racing Center CONTACT / OWNER NAME WATER PURVEYOR RENTON PUBLIC WORKS NEW CONSTRUCTION ASSEMBLY / CUSTOMER ID# PHONE NUMBER ( ) - FAX NUMBER ( ) - PURVEYOR CONTACT NAME Mick Holte ■Y ►ZEN SERVICE ADDRESS / METER NUMBER 17450 W Valley Hw Replacement CUSTOMER / OWNER / CONTACT MAILING ADDRESS PURVEYOR EMAIL ADDRESS backflow@rentonwa.gov CITY / STATE Tukwila WA ZIP CODE 98188-5511 CITY / STATE ZIP CODE - CUSTOMER EMAIL ADDRESS FOR CC chris@junotavern.com ASSEMBLY MANUFACTURER WATTS MODEL LF009QT SERIAL NUMBER 161438 TYPE RPBA SIZE 1/2" DOWNSTREAM HAZARD TYPE or PROPS ICE MAKER LOCATION OF ASSEMBLY NE corner of upstairs bar, lower assembly CONFINED SPACE EYES ONO INSTALLATION TYPE Replacement PREVIOUS MAKE / MODEL / SIZE / SERIAL NUMBER DETECTOR READ N/A ►i1 New • Existing ■ DOH / USC APPROVED 3.9 PSID ORIENTATION H CORRECT INSTALLATION WATER UNE PRESSURE 75 PSIG VALVE POSITIONS PRIOR TO TESTING r YES • NO YES ■ NO SOV#1 MON ►Z@OFF SOV#2 MON ►:DOFF INITIAL TEST RESULTS BAT CERTIFICATION B4536 TEST GAUGE MAKE Mid -West TEST AFTER REPAIRS/CLEANING GAUGE SERIAL NUMBER - 03051790 GAUGE CALIBRATION DATE 01/03/2018 RPBA CHECK VALVE #1 CLOSED TIGHT LEAKED RELIEF VALVE OPENED AT FAILED TO OPEN CHECK VALVE #2 CLOSED TIGHT LEAKED ACTUAL PRESSURE DROPACTUAL ACROSS CHECK VALVE #1 PASSED TEST PHONE NUMBER ( ) - CHECK VALVE #1 CLOSED TIGHT LEAKED RELIEF VALVE OPENED AT FAILED TO OPEN CHECK VALVE #2 CLOSED TIGHT LEAKED PRESSURE DROP ACROSS CHECK VALVE #1 PASSED TEST APPROVED AIR GAP PSID 0 • • • 3.9 PSID DATE OF FINAL TEST 01/22/2018 (I HEREBY CERTIFY THAT I PERSONALLY INSPECTED AND FIELD-TESTED THE ABOVE BACKROW ASSEMBLY USING WAC 246-290-490 APPROVED, USC 101b Ed don TEST PROCEDURES AND USED DIFFERENTIAL PRESSURE TEST EQUIPMENT MEETING WAC 246-292-034 REQUIREMENTS FOR THE ABOVE TEST RESULTS WHICH ARE TRUE, COMPLETE AND ACCURATE) PSID • • @ • • 9.V PSID • ®YES ■ NO EYES ■ NO CLEAN / REPAIR: • see remarks APPROVED AIR GAP OYES • NO ■ YES ■ NO DCVA CHECK VALVE #1 CLOSED TIGHT LEAKED CHECK VALVE #2 CLOSED TIGHT LEAKED PASSED TEST PSID CHECK VALVE #1 CLOSED TIGHT LEAKED CHECK VALVE #2 CLOSED TIGHT LEAKED PASSED TEST PSID PSID • • PSID • • EYES ENO ■YES ■NO CLEAN / REPAIR: ■ see remarks REMARKS Equipment downstream not yet connected at time of testing. VALVE POSTIONS AFTER TESTING SOV#1 MON ►:DOFF SOV#2 ■ON OFF TESTER NAME Jason A. Moe BAT CERTIFICATION B4536 TEST GAUGE MAKE Mid -West GAUGE MODEL 845-5 GAUGE SERIAL NUMBER - 03051790 GAUGE CALIBRATION DATE 01/03/2018 REPAIRED BY N/A COMPANY NAME PHONE NUMBER ( ) - FINAL TEST BY N/A BAT CERTIFICATION TEST GAUGE MAKE GAUGE MODEL COMPANY NAME Fox Plumbing PHONE NUMBER (206) 228-1618 SIGNATURE ._ DATE OF FINAL TEST 01/22/2018 (I HEREBY CERTIFY THAT I PERSONALLY INSPECTED AND FIELD-TESTED THE ABOVE BACKROW ASSEMBLY USING WAC 246-290-490 APPROVED, USC 101b Ed don TEST PROCEDURES AND USED DIFFERENTIAL PRESSURE TEST EQUIPMENT MEETING WAC 246-292-034 REQUIREMENTS FOR THE ABOVE TEST RESULTS WHICH ARE TRUE, COMPLETE AND ACCURATE) 4/2/2018 City of Tukwila Department of Community Development LUKE VASQUEZ 17450 WEST VALLEY HWY TUKWILA, WA 98188 RE: Permit No. PG17-0014 SYKART INDOOR RACING 17450 W VALLEY HWY Dear Permit Holder: Allan Ekberg, Mayor Jack Pace, Director In reviewing our current records, the above noted permit has not received a final inspection by the City of Tukwila Building Division. Per the International Building Code, International Mechanical Code, Uniform Plumbing Cbde and/or the National Electric Code, every permit issued by the Building Division under the provisions of these codes shall expire by limitation and become null and void if the building or work authorized by such permit has not begun within 180 days from the issuance date of such permit, or if the building or work authorized by such permit is suspended or abandoned at any time after the work has begun for a period of 180 days. Your permit will expire on 5/5/2018. Based on the above, you are hereby advised to: 1) Call the City of Tukwila Inspection Request Line at 206-438-9350 to schedule for the next or final inspection. Each inspection creates a new 180 day period, provided the inspection shows progress. -or- 2) Submit a written request for permit extension to the Permit Center at least seven(7) days before it is due to expire. Address your extension request to the Building Official and state your reason(s) for the need to extend your permit. The Building Code does allow the Building Official to approve one extension of up to 180 days. If it is determined that your extension request is granted, you will be notified by mail. In the event you do not call for an inspection and/or receive an extension prior to 5/5/2018, your permit will become null and void and any further work on the project will require a new permit and associated fees. Thank you for your cooperation in this matter. Sincerely, acne Permit Technician )1(1/. File No: PG17-0014 6300 Southcenter Boulevard Suite #100 • Tukwila, Washington 98188 • Phone 206-431-3670 • Fax 206-431-3665 9/29/2017 City of Tukwila Department of Community Development LUKE VASQUEZ 17450 WEST VALLEY HWY TUKWILA, WA 98188 RE: Permit No. PG17-0014 SYKART INDOOR RACING 17450 W VALLEY HWY Dear Permit Holder: Allan Ekberg, Mayor Jack Pace, Director In reviewing our current records, the above noted permit has not received a final inspection by the City of Tukwila Building Division. Per the International Building Code, International Mechanical Code, Uniform Plumbing Code and/or the National Electric Code, every permit issued by the Building Division under the provisions of these codes shall expire by limitation and become null and void if the building or work authorized by such permit has not begun within 180 days from the issuance date of such permit, or if the building or work authorized by such permit is suspended or abandoned at any time after the work has begun for a period of 180 days. Your permit will expire on 11/26/2017. Based on the above, you are hereby advised to: 1) Call the City of Tukwila Inspection Request Line at 206-438-9350 to schedule for the next or final inspection. Each inspection creates a new 180 day period, provided the inspection shows progress. -or- 2) Submit a written request for permit extension to the Permit Center at least seven(7) days before it is due to expire. Address your extension request to the Building Official and state your reason(s) for the need to extend your permit. The Building Code does allow the Building Official to approve one extension of up to 180 days. If it is determined that your extension request is granted, you will be notified by mail. In the event you do not call for an inspection and/or receive an extension prior to 11/26/2017, your permit will become null and void and any further work on the project will require a new permit and associated fees. Thank you for your cooperation in this matter. Sincerely, rA Rachelle Ripley Permit Technician File No: PG17-0014 6300 Southcenter Boulevard Suite #100 • Tukwila, Washington 98188 • Phone 206-431-3670 • Fax 206-431-3665 February 15, 2017 VIA EMAIL AND US MAIL Mr. Luke Vasquez General Manager SyKart Indoor Racing Center, LLC 17450 West Valley Highway Tukwila, WA 98188 Denis Law Mayor Public Works Department - Gregg Zimmerman, P.E., Administrator RE: PLUMBING/GAS PIPING Permit Application Number PG17-0014 SYKART INDOOR RACING —17450 W VALLEY HWY Dear Mr.Vasquez The City of Renton has reviewed your proposed addition of a new lounge/snack bar for the SyKart Indoor Racing Center, LLC located at 17450 West Valley Highway. Based upon the proposed use, the City of Renton recommends installing a grease trap for this application. We suggest a 70 gallon grease trap but defer to the City of Tukwila, plumbing requirements, for approval of sizing. If you have any questions regarding the City of Renton's recommendation, please contact me by phone at 425-430-7206 or email at mbenoit@rentowa.gov. Sincerely, Michael A. Benoit WasteWater Utility RECEIVED CITY OF TUKWILA FEB 2 1 2017 PERMIT CENTER cOriFIE PCftOOt4 H:\File:Sys\WWP WasteWater\WWP-03-0000 Correspondence.-Wastewater\MikeB\SyKart Indoor.doc\MABcv 1055 South Grady Way, Renton, WA 98057 • rentonwa.gov Non -Residential Sewer Use Certification kg King County Department of Natural Resources and Parks Wastewater Treatment Division • To be completed for all new sewer connections, reconnections or change of use of existing connections. • This form does not apply to repairs or replacements of existing sewer connections within five years of disconnect. Please Print or Type 9-1/sa A f Property Street Address City #/6," i Com: Owners Name 41/ _ WA eekState / Subdivision Name Subdiv. # t. Building Name . S KCE12.71— �,c j—. it plicable) t ) Own is Phone ;Armin!! NAM lea Cede) ) Piopcny Contact Phone Number with Area Code) Owner's Mailing Address Lot # __ Block # fal 24 (AM q8/C�+ Property Tax ID # Party to be Billed (if different from owner) 5• City or Sewer District .ett7IfT.Frstsvettilal Date of Connection Side Sewer Permit # /"4c--/ 7 - Please report any demolitions of pre-existing building on this property. Credit for a demolition may be given under some circumstances. Demolition of pre-existing building? ❑Yes INo Was building on Sanitary Sewer? :•i Yes LI No Was Sewer connected before 2/1/90? l es ❑No Sewer disconnect date Type of building demolished Request to apply demolition credit to multiple buildings? ❑Yes ❑ No A. Fixture Units Fixture Units x Number of Fixtures = Total Fixture Units Kind of Fixture fixture Units No. o) fixtures total ._ Fixture Units Public Private Public Private Bathtub and Shower4 _ ------ Shower, per head `._.._... �2 .r 4 _. Z_.._. __.__.__ _ _ _ ___ Dishwasher 2 2 Drinking fountain (each head) 1 .5 Hose Bibb (interior) 2.5 2.5 Clotheswasher or laundry tub 4 2 _ _ / / Sink, bar or lavatory Sink, Clinic flushing 8 8 Sink, kitchen 3 2 Sink, other (service) 3 1.5 3 Sink, wash fountain, circle spray 43 _ 2 2 0 Urinal, flush valve, 1 GPF 5 6 Urinal, flush valve, >1 GPF Urinal, waterless 0 Water closet, tank or valve, 1.6 GPF 6 3 Water closet, tank or valve, >1.6 GPF 8 4 Total Fixture Units ____/_ Residential Customer Equivalent (RCE) 20 fixture units equal 1.0 RCE Total No. of Fixture Units_ I 9 5 I RCE J B. Other Wastewater Flow (in addition to Fixture Units identified in Section A) Type of Facility/Process: Estimated Wastewater Discharge: Gallons/days Residential Customer Equivalents (RCE): 187 gallons per day equals 1.0 RCE Total Discharge (gal/day) _ 187 RCE C. Total Residential Customer Equivalents: (add A & B) RECEIVED jj CITY OF TUKWILA B _ _ FEB 2 1 2017 PERMIT CENTER RCE COF T N c� .The am ntofdte Pursuant to King County Code 28.84, all sewer customers who establish a new service which use metropolitan sewage facilities shall be subject to a ca charge is established annually by the King County Council at a rate per month per residential customer or residential customer equivalent for a period of fifteen years. The purpore71171M1rrfIrterover costs of providing sewage treatment capacity for new sewer customers. The charge is collected quarterly. All future billings can be prepaid at a discounted amount. Questions regarding the capacity charge or this form should be referred to King County's Wastewater Treatrnent Division at 206-477-5533. I certify that the information given is correct. I understand that the capacity charge levied will be b require resubmission of corrected data for determination of a revised capacity charge. Signature of Owner/Representative Print ., Owner/Representative----- 1858 (Revs. 4/15) t is infimati Date i� Z�/ 7- White — King County Yellow — Local Sewer Agency Piny — Sewer Customer CITY OF RENTON APPLICATION FIR SEWER SavFCE `" d >✓ he o& make eppliiellan tar Sewer Service She p tweed at No. j;7l/SC___p7V Y • en Lot ESO... .--- �' AQdlttoT D•r' The ewer is le be head tor_,....., : ,fir,.. it.?F ±{''; ....,...,.. atf! ......___—•-•.-�cet to pall i'iltes now or Mitts b etteet tot £u± !ureic and cap wlth au Um tu1aa and Some et .+ tom In Oral:ems too >» algae; radlading wit pea et Web Service and tat it of plumtsla j !b1ueee, Eft et ....kr, Bewtr Lala 4.--..��...�.::7 _..r��.t......,.. ='' ...ge4r!g. 14I 44t S-.1 ..- -1- j Z. •. 1; ..._. i. t.iii • a 4 . .- , �} I • `h 1•ll .t V V 1— --• T N • M. 1 APPLICATION FOR SEWER SERVICE Doto..I, j., 1$. ..ria...,.... 0, i! ht sby Matte Opl'eatirn far Sewer S+' yes for the promisee 3 No. �I .e J 04_476- op k.4} ct property g r Tho Sewer Is to he u for.— ...:.. ......... ....,[',.?:.,�"�-. .G .F. -,.....purposes, and _._.. '... ee to p$?' the rates neer or hereafter in effect kr such service Rid comply oath allAc roles find rah rittlon n; xtt forth Sn Ordinance to be adopted reggragg the ill oL st4eh ,ter:ice sn<S the cars of plumbing ftAinitsi, t Signed. . " . _, ` ..„.A 'x3.1.t.1 "* .-„ _'.. P Lf• sin a+ #?Spc r mind h SCwer Laic! bp. , ,,'-i4.. ' 2,- f a/ jai 5 < C V From: Joanna Spencer[mailto:Joanna.Spencer{aTukwilaWA.gov] Sent: Wednesday, December 07, 2016 10:49 AM To: Abdoul Gafour Cc: Joanna Spencer Subject: Sykart Indoor Racing Center @ 17450 W Valley Hwy D16-0331 Good Morning, They have applied for a TI which includes installation of commercial kitchen and lounge and they will cook & serve food to their customers. Whenever there is food prep, PW requires installation of a grease trap/interceptor inside. Since it is Renton sewer, what's you take? They haven't applied for a plumbing permit yet.Is it Renton water as well. Please advise. Best, Joanna Spencer Development Engineer Public Works Department 6300 Southcenter Blvd, Suite 100, Tukwila, WA 98188-2544 Phone: 206 431-2440 Fax: 206 431-3665 4 414 Joanna Spencer From: David Christensen <Dchristensen@Rentonwa.gov> Sent: Wednesday, December 07, 2016 11:46 AM To: Joanna Spencer Cc: Richard Moreno; Abdoul Gafour Subject: RE: Sykart Indoor Racing Center @ 17450 W Valley Hwy D16-0331 Joanna, Renton will require that grease traps or interceptors be installed in a commercial kitchen. We would want to know the number of seats, and what time they serve meals to help us decide whether or not we will require an interceptor versus traps. If it is an interceptor, they will permit the installation through our public works permit counter. If we determine traps are acceptable, we would look to your plumbing inspectors to ensure the correct devices are installed in accordance with the plumbing code. Thanks, for the heads up on this. Dave Christensen Wastewater Utility Engineering Manager 425.430.7212 From: Abdoul Gafour Sent: Wednesday, December 07, 2016 10:59 AM To: David Christensen Cc: 'Joanna Spencer'; Richard Moreno Subject: FW: Sykart Indoor Racing Center @ 17450 W Valley Hwy D16-0331 Hi Joanna, I am forwarding your request to Dave Christensen, the City's wastewater engineering manager. Dave will provide you with the City's requirements and information regarding the installation of the grease trap, permit and inspection. Thanks for keeping us in the loop. Abdoul Gafour Water Utility Engineering Manager City of Renton Public Works 1055 S Grady Way Renton, WA 98057 425430-7210 agafourPrentonwa.gov 1 P611 -DO) 1/4 4% o 4 ../ t 1 a 2 2�4 January 31, 2017 City of Tukwila Department of Community Development LUKE VASQUEZ 17450 WEST VALLEY HWY TUKWILA, WA 98188 RE: Correction Letter # 1 PLUMBING/GAS PIPING Permit Application Number PG17-0014 SYKART INDOOR RACING - 17450 W VALLEY HWY Dear LUKE VASQUEZ, Allan Ekberg, Mayor Jack Pace, Director This letter is to inform you of corrections that must be addressed before your development permit can be approved. All correction requests from each department must be addressed at the same time and reflected on your drawings. I have enclosed comments from the following departments: PW - PG DEPARTMENT: Joanna Spencer at 206-431-2440 if you have questions regarding these comments. 1) Since water and sewer services are provided by City of Renton, applicant shall submit plans to Mr. Dave Christen, Renton Wastewater Utility Engineering Manager, phone 425 430-7212, so Renton can make a determination if an outside grease interceptor or a trap shall be required. Proposed number of seats and what time meals are going to be served information shall be provided. If Renton determines that an interceptor is required applicant shall obtain a permit from City of Renton Public Works. If Renton determines that grease trap is acceptable it will be permitted under Tukwila Plumbing Permit. See attached Renton email. 2) If grease trap is acceptable, please include grease trap cut sheet/installation & maintenance manual. 3) Due to addition of new plumbing fixture unit's applicant shall submit executed King County Non -Residential Sewer Use Certification Form. List only new fixture units and not the one replaced in kind. Please address the comments above in an itemized format with applicable revised plans, specifications, and/or other documentation. The City requires that two (2) sets of revised plan pages, specifications and/or other documentation be resubmitted with the appropriate revision block. In order to better expedite your resubmittal, a 'Revision Submittal Sheet' must accompany every resubmittal. I have enclosed one for your convenience. Corrections/revisions must be made in person and will not be accepted through the mail or by a messenger service. If you have any questions, I can be reached at (206) 433-7165. Sincerely, Rachelle Ripley Permit Technician File No. PG17-0014 6300 Southcenter Boulevard Suite #100 • Tukwila Washington 98188 • Phone 206-431-3670 • Fax 206-431-3665 PERMIT COORD COPY PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG17-0014 DATE: 02/22/17 PROJECT NAME: SYKART INDOOR RACING CENTER SITE ADDRESS: 17450 W VALLEY HWY Original Plan Submittal Revision # before Permit Issued X Response to Correction Letter # 1 Revision # after Permit Issued DEPARTMENTS: Building Division JA oNvi7j Public Works n Fire Prevention Structural Planning Division ❑ Permit Coordinator PRELIMINARY REVIEW: Not Applicable n (no approval/review required) REVIEWER'S INITIALS: DATE: 02/22/17 Structural Review Required DATE: 4 APPROVALS OR CORRECTIONS: Approved Corrections Required DUE DATE: 03/23/17 Approved with Conditions n ❑ Denied (corrections entered in Reviews) Notation: (ie: Zoning Issues) REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping 111 PW ❑ Staff Initials: 12/18/2013 PERMIT COORD COPD PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG17-0014 DATE: 01/25/17 PROJECT NAME: SYKART INDOOR RACING CENTER SITE ADDRESS: 17450 W VALLEY HWY X Original Plan Submittal Response to Correction Letter # Revision # before Permit Issued Revision # after Permit Issued DEPARTMENTS: Pr's GNU 10) Building Divisio Public Works ��lfl1 Fire Prevention Structural n Planning Division ❑ Permit Coordinator PRELIMINARY REVIEW: Not Applicable ❑ (no approval/review required) DATE: 01/26/17 Structural Review Required REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: DUE DATE: 02/23/17 Approved Approved with Conditions Corrections Required ❑ Denied ❑ (ie: Zoning Issues) (corrections entered in Reviews) Notation: REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW 1Yr Staff Initials: 12/18/2013 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Web site: http://www.TukwilaWA.gov REVISION SUBMITTAL Revision submittals must be submitted in person at the. Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: 2/A0/-7 ❑ Response to Incomplete Letter # N. Response to Correction Letter # .� ❑ , Revision # after Permit is Issued ❑. Plan Check/Permit Number: PCS / ' — 0a/4/ Revision requested by a City Building Inspector or Plans Examiner ❑ Deferred Submittal # Project Name: syk4tj" _A/ %O! iedqeiN9 66.j 7 /2 Project Address: /-7-L/• L&) ()AU y may, %G(k l/f,,4 IAJA q8'/re Contact Person: Zit,_ 1.1 v`QU Phone Number: 2-1/7 - 22.6 -3 °?-7/ Summary of Revision: "d%/ IS.SEED {.mac T W/'!M/ G!YY C P__�M /11611.,0111 6c(T .rde 7 eA L ,s6We CL r6e-fi c4- co, jI. Sheet Number(s): P2 .0 "Cloud" or highlight all areas of revision including date of revision Received at the City of Tukwila Permit Center by: ❑ Entered in TRAKiT on W:\Pcrmit Center \Templates\Forms\Revision Submittal Form.doc Revised: August 2015 CITY OF TUKWILA Department of Community Development 6300 Southcenter Boulevard, Tukwila, WA 98188 Telephone: (206) 431-367o FAX (206) 431-3665 E-mail: tukplan@ci.tukwila.wa.us Permit Center/Building Division 206 431-3670 Public Works Department 206 433-0179 Planning Division 206 431-3670 AFFIDAVIT IN LIEU OF CONTRACTOR REGISTRATION STATE OF WASHINGTON) ) ss. COUNTY OF KING -Todd /3 �— [please print name] , states as follows: PERMIT NO: VCiri °°1 11 1. I have made application for a permit from the City of Tukwila, Washington. 2. I understand that state law requires that all building construction contractors be registered with the State of Washington. The exceptions to this requirement are stated under Section 18.27.090 of the Revised Code of Washington, a copy of which is printed on the reverse side of this Affidavit. I have read or am familiar with RCW 18.27.090. 3. I understand that prior to issuance of a permit for work which is to be done by any contractor, the City of Tukwila must verify either that the contractor is registered by the State of Washington, or that one of the exemptions stated under RCW 18.27.090 applies. 4. In order to provide verification to the City of Tukwila of my compliance with this requirement, I hereby attest that after reading the exemptions from the registration requirement of RCW 18.27.090, I consider the work authorized under this permit to be exempt under number / 3, and will therefore not be performed by a registered contractor. 5. I understand that the licensing provision of RCW 19.28.161 through 19.28.271 shall not apply to persons making electrical installations on their own property or to regularly employed employees working on the premises of their employer. The proposed electrical work is not for the construction of a new building for rent, sale or lease. I understand that I may be waiving certain rights that I might otherwise have under state law in any decision to engage an unregistered contractor to perform construction work. • Owner/Owner s Agent* Signed and sworn to,,before me this day of 60 , 2011 . NOTARY ' UBLIC n and Residing at the State of Washington Name as commissioned My commission expires: P. - 18.27.090 Exemptions. The registration provisions of this chapter do not apply to: 1. An authorized representative of the United States government, the state of Washington, or any incorporated city, town, county, township, irrigation district, reclamation district, or other municipal or political corporation or subdivision of this state; 2. Officers of a court when they are acting within the scope of their office; 3. Public utilities operating under the regulations of the utilities and transportation commission in construction, maintenance, or development work incidental to their own business; 4. Any construction, repair, or operation incidental to the discovering or producing of petroleum or gas, or the drilling, testing, abandoning, or other operation of any petroleum or gas well or any surface or underground mine or mineral deposit when performed by an owner or lessee; 5. The sale of any finished products, materials, or articles of merchandise that are not fabricated into and do not become a part of a structure under the common law of fixtures; 6. Any construction, alteration, improvement, or repair of personal property performed by the registered or legal owner, or by a mobile/manufactured home retail dealer or manufacturer licensed under chapter 46.70 RCW who shall warranty service and repairs under chapter 46.7o RCW; 7. Any construction, alteration, improvement, or repair carried on within the limits and boundaries of any site or reservation under the legal jurisdiction of the federal government; 8. Any person who only furnished materials, supplies, or equipment without fabricating them into, or consuming them in the performance of, the work of the contractor; 9. Any work or operation on one undertaking or project by one or more contracts, the aggregate contract price of which for labor and materials and all other items is less than five hundred dollars, such work or operations being considered as of a casual, minor, or inconsequential nature. The exemption prescribed in this subsection does not apply in any instance wherein the work or construction is only a part of a larger or major operation, whether undertaken by the same or a different contractor, or in which a division of the operation is made into contracts of amounts less than five hundred dollars for the purpose of evasion of this chapter or otherwise. The exemption prescribed in this subsection does not apply to a person who advertises or puts out any sign or card or other device which might indicate to the public that he or she is a contractor, or that he or she is qualified to engage in the business of contractor; 10. Any construction or operation incidental to the construction and repair of irrigation and drainage ditches of regularly constituted irrigation districts or reclamation districts; or to farming, dairying, agriculture, viticulture, horticulture, or stock or poultry raising; or to clearing or other work upon land in rural districts for fire prevention purposes; except when any of the above work is performed by a registered contractor; 11. An owner* who contracts for a project with a registered contractor, except that this exemption shall not deprive the owner of the protections of this chapter against registered and unregistered contractors. The exemption prescribed in this subsection does not apply to a person who performs the activities of a contractor for the purpose of leasing or selling improved property he or she has owned for less than twelve months; 12.* Any person working on his or her own property, whether occupied by him or her or not, and any person working on his or her personal residence, whether owned by him or her or not but this exemption shall not apply to any person who performs the activities of a contractor on his or her own property for the purpose of selling, demolishing, or leasing the property; 13. An owner* who performs maintenance, repair, and alteration work in or upon his or her own properties, or who uses his or her own employees to do such work; 14. A licensed architect or civil or professional engineer acting solely in his or her professional capacity, an electrician certified under the laws of the state of Washington, or a plumber certified under the laws of the state of Washington or licensed by a political subdivision of the state of Washington while operating within the boundaries of such political subdivision. The exemption provided in this subsection is applicable only when the person certified is operating within the scope of his or her certification; 15. Any person who engages in the activities herein regulated as an employee of a registered contractor with wages as his or her sok compensation or as an employee with wages as his or her sole compensation; 16. Contractors on highway projects who have been prequalified as required by RCW 47.28.070, with the department of transportation to perform highway construction, reconstruction, or maintenance work; 17. A mobile/manufactured home dealer or manufacturer who subcontracts the installation, set-up, or repair work to actively registered contractors. This exemption only applies to the installation, set-up, or repair of the mobile/manufactured homes that were manufactured or sold by the mobile/manufactured home dealer or manufacturer; 18. An entity who holds a valid electrical contractor's license under chapter 19.28 RCW that employs a certified journeyman electrician, a certified residential specialty electrician, or an electrical trainee meeting the requirements of chapter 19.28 RCW to perform plumbing work that is incidentally, directly, and immediately appropriate to the like -in-kind replacement of a household appliance or other small household utilization equipment that requires limited electric power and limited waste and/or water connections. An electrical trainee must be supervised by a certified electrician while performing plumbing work. Per Washington State Department of Labor and Industries lessee has been interpreted to be equivalent to owner for purposes of exemptions. PLUMBING GENERAL NOTES 1. COMPLETE INSTALLATION OF THE MECHANICAL SYSTEM SHALL BE PER THE STATE OF WASHINGTON BUILDING, MECHANICAL ENERGY, FIRE, PLUMBING AND HEALTH CODES AND REGULATIONS AS ADOPTED BY LOCAL JURISDICTIONS. 2. ALL EQUIPMENT/FIXTURES SHALL BE THE CAPACITY AND TYPES AS SHOWN ON THE PLUMBING SCHEDULE AND SHALL BE THE LISTED MANUFACTURER AND MODEL NUMBER OR SHALL BE AN EQUAL APPROVED BY THE OWNER/ENGINEER. 3. THE CONTRACTOR SHALL SUBMIT MINIMUM OF SIX COPIES OF EQUIPMENT/FIXTURE SUBMITTALS FOR APPROVAL. 4. CONTRACTOR IS TO BRING UP THE DISCREPANCIES AND ITEMS WHICH ARE NOT SPECIFICALLY CALLED FOR OR SHOWN BUT ARE REQUIRED FOR A COMPLETE MECHANICAL SYSTEM AND AFFECT HIS CONTRACT PRIOR TO ENTERING AND SIGNING THE CONTRACT; AFTER AWARDING THE CONTRACT ALL SUCH ITEMS REQUIRED FOR A COMPLETE, SYSTEM READY FOR THE OWNER'S BENEFICIAL USE SHALL BE FURNISHED AND INSTALLED INCLUDING ALL SUCH DISCREPANCY ITEMS MENTIONED ABOVE, AT NO ADDITIONAL COST TO THE OWNER AND PER LOCAL CODES. MANUFACTURER'S RECOMMENDATIONS AND APPLICABLE STANDARDS WITH THE ARCHITECT/ENGINEER'S APPROVAL. 5. ALL EQUIPMENT/FIXTURES SUPPLIED FOR THESE SPECIFICATIONS SHALL BE FREE FROM DEFECTS IN MATERIAL, WORKMANSHIP, AND TITLE, AND SHALL BE OF THE KIND AND QUALITY DESCRIBED HEREIN. IF IT APPEARS WITHIN ONE YEAR FROM DATE OF FINAL ACCEPTANCE THAT EQUIPMENT DOES NOT MEET THE WARRANTIES ABOVE, THE CONTRACTOR SHALL IMMEDIATELY CORRECT ANY DEFECT AND SHALL RESTORE THE SYSTEM TO THE ORIGINAL SATISFACTORY CONDITIONS AT HIS EXPENSE. THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF OTHER WARRANTIES, WHETHER WRITTEN, ORAL, IMPLIED OR STATUTORY. NO WARRANTY OF MERCHANT ABILITY OF FITNESS FOR PURPOSE SHALL APPLY. (THE WARRANTY SHALL START FROM THE TIME OF ARCHITECT/ENGINEER'S FINAL ACCEPTANCE.) 6. ENTIRE INSTALLATION:, OF ALL EQUIPMENT, FIXTURES, PIPING, PLUMBING AND RELATED ACCESSORIES SHALL BE PER BASIC OWNERS' STANDARDS. MECHANICAL CONTRACTOR IS TO FAMILIARIZE HIMSELF WITH THESE STANDARDS. 7. COORDINATE WITH THE STRUCTURAL ENGINEER TO PROVIDE STRUCTURAL SUPPORT FOR ALL EQUIPMENT. 8. COORDINATE THE CONSTRUCTION SCHEDULE WITH THE ARCHITECT AND PERFORM ALL REQUIRED WORK IN STRICT ACCORDANCE WITH THE OWNER'S SCHEDULE. 9. PLUMBING CONTRACTOR SHALL PAY FOR AND OBTAIN ALL REQUIRED PERMITS AND CERTIFICATES REQUIRED BY THE AUTHORITIES HAVING JURISDICTION. 10. ADJUST ALL EQUIPMENT AND PERFORM A COMPLETE WATER -BALANCING AND PUT ALL PLUMBING SYSTEMS IN OPERATION. 11. AIR-CONDITIONING UNIT COIL WITHOUT INTERNAL TRAP SHALL HAVE A P -TRAP (3" MIN. SEAL) FOR THE CONDENSATE PAN. DISCHARGE CONDENSATE DRAIN TO ROOF DRAIN. 12. PLUMBING CONTRACTOR SHALL VISIT THE SITE TO DETERMINE THE EXACT IMPACT OF THE NEW CONSTRUCTION FOR THE PLUMBING SYSTEM AND SHALL INCLUDE IN HIS BID ALL THE WORK WHICH MIGHT NOT BE SPECIFICALLY MENTIONED BUT ARE REQUIRED FOR A COMPLETE PLUMBING SYSTEM READY FOR OWNER'S BENEFICIAL USE. 13. COLD WATER LINES WITH OVER 70-80 PSIG PRESSURES REQUIRE PRESSURE REDUCING VALVE AND STRAINER. 14. SCOPE OF WORK: THE CONTRACTOR SHALL INCLUDE IN HIS BID ALL THE COST RELATED TO INSTALLING NEW PIPING TO ALL NEW FIXTURES AS SHOWN AND AS REQUIRED BY THE UNIFORM PLUMBING CODE AND THE LOCAL JURISDICTIONS. ALL PLUMBING SYSTEM (PIPING, FIXTURES, EQUIPMENT, ETC.) INSIDE THE BUILDING SHALL BE NEW AND CONNECT TO NEW SANITARY AND NEW WATER PIPES OUTSIDE THE BUILDING. THE CONTRACTOR SHALL INCLUDE IN HIS BID ALL THE COST RELATED TO INVESTIGATING THE ROUTING OF SITE UTILITY PIPES IN ORDER TO MAKE NEW CONNECTIONS FOR THE NEW FIXTURES. (THE PIPE ROUTING AND CONNECTIONS MAY NOT BE SPECIFICALLY SHOWN ON THE DRAWINGS) THE CONTRACTOR SHALL INCLUDE IN HIS BID ALL THE COSTS REQUIRED FOR ALL THE PIPING TO MEET THE PIPE SIZES PER THE UNIFORM PLUMBING CODES TABLES -6-4 & 7-5. 15. SEE ARCHITECTURAL DRAWINGS AND SPECIFICATIONS FOR ADDITIONAL SCOPE OF WORK, INSTRUCTION TO BIDDERS AND EXACT LOCATION OF ALL FIXTURES. 16. PLUMBING CONTRACTOR SHALL INSTALL ALL HOT AND COLD WATER PIPING WITHIN THE HEATED AREAS FOR FREEZE PROTECTION. 17. COORDINATE EXACT LOCATION OF ALL EQUIPMENT, FIXTURES, PIPING, ETC. AND PENETRATIONS WITH THE ARCHITECTURAL STRUCTURAL AND AT SITE. 18. ALL APPLICABLE CODES AND LOCAL JURISDICTION REGULATIONS SHALL SUPERSEDE THE CONSTRUCTION DOCUMENTS IF THEY ARE MORE STRINGENT. 19. INSTALL ALL TRAP ARMS SUCH THAT THE MAXIMUM LENGTH WILL NOT EXCEED THE CODE REQUIREMENTS. 20. ALL FIXTURES REQUIRING PLUMBING SHALL BE CONNECTED TO BUILDING WASTE, VENT, COLD WATER AND HOT WATER SYSTEM AS REQUIRED BY THE CODES. 21. INSTALL CLEANOUTS PER THE 2009 UPC -SECTION 707 AND AS REQUIRED BY LOCAL JURISDICTIONS. 22. PIPE MATERIAL: COLD WATER & HOT WATER COPPER "L" (ABOVE GROUND)(LEAD FREE) COLD WATER & HOT WATER COPPER "K"(UNDERGROUND)(LEAD FREE) WASTE AND VENT CAST IRON, DWV COPPER, ABS. NOTE: JOINTS AND METHOD OF CONNECTIONS SHALL BE PER THE 2003 UPC -CHAPTER #14, ASTM STANDARDS AND MANUFACTURERS RECOMMENDATIONS FOR EACH PIPE TYPE AND APPLICATIONS. 23. PIPE INSULATION: COLD WATER - 1/2" INSULATION WITH VAPOR BARRIER JACKETS. HOT WATER - 1/2" INSULATION WITH VAPOR BARRIER JACKETS. FOR RUNOUTS UP TO 12 FEET AND 1" INSULATION FOR ALL PIPING UP TO 2" DIAMETER. UNDERGROUND PIPING WITH 1/2" CLOSED CELL FOAM INSULATION. RAIN LEADER & OVERFLOW 7 1/2" INSULATION WITH VAPOR BARRIER JACKETS. 24. PIPE HANGERS AND SUPPORTS: PIPE HANGERS AND SUPPORTS SHALL BE IN STRICT ACCORDANCE WITH THE 2003 UPC -SECTION -314 AND PIPE MANUFACTURERS RECOMMENDATIONS. ALL PIPES SHALL BE SEISMICALLY RESTRAINED PER LATEST EDITION OF S.M.A.C.N.A. SEISMIC RESTRAINT MANUAL AND AS REQUIRED BY LOCAL JURISDICTION. 25. THE CONTRACTOR SHALL INCLUDE ALL EXCAVATION AND BACKFILLING REQUIRED FOR UNDERGROUND WORK IN HIS BID UNLESS OTHER ARRANGEMENTS ARE MADE WITH THE GENERAL CONTRACTOR PRIOR TO BIDDING. (COORDINATE WITH SITE/CIVIL ENGINEER). 26. DOMESTIC HOT WATER SYSTEM SHALL BE SET FOR 120T OR AS REQUIRED BY LOCAL JRSD. 27. ALL WATER LINES SHALL BE STERILIZED IN ACCORDANCE WITH THE A.W.W.A. STANDARDS AND LOCAL REGULATIONS. 28. WATER SUPPLY LINE TO AIR/WATER STATION SHALL HAVE BACK FLOW PREVENTIONS AS REQUIRED BY THE JURISDICTIONS. 29. WATER HEATER RELIEF SHALL BE PIPED TO OUTSIDE. 30. ALL MATERIALS USED SHALL BE NEW AND BEAR U.L. LABEL WHEN REQUIRED. 31. FINAL AS BUILT DRAWINGS SHALL BE SUBMITTED TO ENGINEER/OWNER. 32. ALL OPENINGS AND PENETRATIONS THROUGH ROOF AND/OR WALLS SHALL BE PROPERLY SEALED, WEATHERTIGHT, AND AESTHETICALLY ACCEPTABLE. 33. ALL CUTTING AND PATCHING REQUIRED FOR INSTALLATION OF NEW EQUIPMENT, FIXTURES AND PIPING TO BE BY CONTRACTOR. 34. INSTALL AIR CHAMBERS BEHIND EACH OUTLET OR WADE-SHOKSTOPS FOR EACH FIXTURE. GROUP FOR WATER HAMMER ARRESTORS. GENERAL SPECIFICATIONS A. IT IS THE INTENT OF THESE SPECIFICATIONS TO PROVIDE A MECHANICAL SYSTEM COMPLETE, FULLY ADJUSTED, AND READY TO USE. B. INSPECTION: PRIOR TO ALL WORK OF THIS DOCUMENT, CAREFULLY INSPECT THE INSTALLED WORK OF ALL OTHER TRADES AND -VERIFY THAT ALL SUCH WORK IS COMPLETE TO THE POINT WHERE THIS INSTALLATION MAY PROPERLY COMMENCE. VERIFY THAT THE WORK MAY BE COMPLETED IN STRICT ACCORDANCE WITH ALL PERTINENT CODES AND REGULATIONS, THE APPROVED SHOP DRAWINGS, AND THE MANUFACTURERS' RECOMMENDATIONS. C. DISCREPANCIES: IN THE EVENT OF DISCREPANCY, IMMEDIATELY NOTIFY THE ARCHITECT/ENGINEER. DO NOT PROCEED IN AREAS OF DISCREPANCY UNTIL ALL SUCH DISCREPANCIES HAVE BEEN FULLY RESOLVED. D. INSPECTION: CHECK EACH PIECE OF EQUIPMENT IN THE SYSTEM FOR DEFECTS, VERIFYING THAT ALL PARTS ARE PROPERLY FURNISHED AND INSTALLED, THAT ALL ITEMS FUNCTION PROPERLY, AND THAT ALL ADJUSTMENTS HAVE BEEN MADE. E. GENERAL: DO NOT ALLOW OR CAUSE ANY OF THE WORK OF THIS SECTION TO BE COVERED UP OR ENCLOSED UNTIL IT HAS BEEN INSPECTED, VIEWED AND ACCEPTED BY THE LANDLORD/ARCHITECT/ ENGINEER AND BY ALL OTHER AUTHORITIES HAVING JURISDICTIONS. F. DO ALL THINGS NECESSARY TO COOPERATE WITH OTHER TRADES IN ORDER THAT ALL SYSTEMS IN THE WORK MAY BE INSTALLED IN THE BEST ARRANGEMENTS. COORDINATE AS REQUIRED WITH ALL OTHER TRADES TO SHARE SPACE IN COMMON AREAS AND TO PROVIDE THE MAXIMUM OF ACCESS TO EACH SYSTEM. G. IT IS THE INTENT OF THESE SPECIFICATIONS THAT ALL WORK, INCLUDING THE INSIDE OF EQUIPMENT, FIXTURES, PIPING, DUCTWORK, ETC. BE LEFT IN A CLEAN CONDITION. ALL CONSTRUCTION DIRT SHALL BE REMOVED FROM MATERIAL SITE AND EQUIPMENT. H. IT IS THE INTENTION OF THESE SPECIFICATIONS AND DRAWINGS TO CALL FOR FINISHED WORK, TESTED, AND READY FOR OPERATION. WHEREVER THE WORK "PROVIDE" IS USED, IT SHALL MEAN "FURNISH AND INSTALL COMPLETE AND READY TO USE." MINOR DETAILS NOT USUALLY SHOWN OR SPECIFIED, BUT NECESSARY FOR THE PROPER INSTALLATION AND OPERATION, SHALL BE INCLUDED IN THE WORK, THE SAME AS IF HEREIN SPECIFIED OR SHOWN. I. THE CONTRACTOR SHALL GIVE ALL NECESSARY NOTICES, OBTAIN ALL PERMITS AND PAY ALL GOVERNMENT SALES TAXES, FEES AND OTHER COSTS, INCLUDING UTILITY CONNECTIONS OR EXTENSIONS, IN CONNECTION WITH HIS WORK; FILE ALL NECESSARY PLANS, PREPARE ALL DOCUMENTS AND OBTAIN ALL NECESSARY APPROVALS OF ALL GOVERNMENTAL DEPARTMENTS HAVING JURISDICTION; OBTAIN ALL REQUIRED CERTIFICATES OF INSPECTION OF HIS WORK AND DELIVER SAME TO THE ARCHITECT BEFORE REQUEST FOR ACCEPTANCE AND FINAL PAYMENT FOR WORK. J. THE CONTRACTOR SHALL INCLUDE IN THE WORK, WITHOUT EXTRA COST TO THE OWNER, ANY LABOR, MATERIALS, SERVICES, APPARATUS, DRAWINGS, IN ORDER TO COMPLY WITH ALL APPLICABLE LAWS, ORDINANCES, RULES AND REGULATIONS, WHETHER OR NOT SHOWN ON DRAWINGS AND/OR SPECIFIED. K. SURVEYS AND MEASUREMENTS: THE CONTRACTOR SHALL BASE ALL MEASUREMENTS, BOTH HORIZONTAL AND VERTICAL, FROM ESTABLISHED BENCH MARKS. ALL WORK SHALL AGREE WITH THESE ESTABLISHED LINES AND LEVELS. VERIFY ALL MEASUREMENTS AT SITE AND CHECK THE CORRECTNESS OF SAME AS RELATED TO THE WORK. L. DRAWINGS: DRAWINGS ARE DIAGRAMMATIC AND INDICATE THE GENERAL ARRANGEMENT OF SYSTEMS AND WORK INCLUDED IN THE CONTRACT. DRAWINGS ARE NOT TO BE SCALED. THE ARCHITECTURAL DRAWINGS AND DETAILS SHALL BE EXAMINED FOR EXACT LOCATION OF FIXTURES AND EQUIPMENT. WHERE THEY ARE NOT DEFINITELY LOCATED, THIS INFORMATION SHALL BE OBTAINED FROM THE ARCHITECT. M. PROTECTION: THE CONTRACTOR SHALL BE RESPONSIBLE FOR WORK AND EQUIPMENT UNTIL FINALLY INSPECTED, TESTED, AND ACCEPTED; HE SHALL PROTECT WORK AGAINST THEFT, INJURY OR DAMAGE; AND SHALL CAREFULLY STORE MATERIAL AND EQUIPMENT RECEIVED ON SITE WHICH ARE NOT IMMEDIATELY INSTALLED. HE SHALL CLOSE OPEN ENDS OF WORK WITH TEMPORARY COVERS OF PLUGS DURING STORAGE AND CONSTRUCTION TO PREVENT ENTRY OF OBSTRUCTING MATERIAL. N. THE CONTRACTOR SHALL FURNISH ALL SCAFFOLDING, RIGGING, HOISTING, AND SERVICES NECESSARY FOR ERECTION AND INSTALLATION OF THE MECHANICAL SYSTEM. 0. CONTRACTOR SHALL LOCATE ALL EQUIPMENT WHICH MUST BE SERVICED, OPERATED, OR MAINTAINED IN FULLY ACCESSIBLE POSITIONS. P. THIS CONTRACTOR SHALL PROVIDE ALL CUTTING AND PATCHING NECESSARY TO INSTALL THE WORK SPECIFIED IN THIS SECTION. PATCHING SHALL MATCH ADJACENT SURFACES. Q. NO STRUCTURAL MEMBERS SHALL BE CUT WITHOUT THE APPROVAL OF THE ARCHITECT, AND ALL SUCH CUTTING SHALL BE DONE IN A MANNER DIRECTED BY HIM. R. THIS CONTRACTOR SHALL PROVIDE AND LOCATE ALL SLEEVES AND INSERTS REQUIRED BEFORE THE FLOORS AND WALLS ARE BUILT, OR SHALL BE RESPONSIBLE FOR THE COST OF CUTTING AND PATCHING REQUIRED FOR PIPES WHERE SLEEVES AND INSERTS WERE NOT INSTALLED, OR WHERE INCORRECTLY LOCATED. THE CONTRACTOR SHALL DO ALL DRILLING REQUIRED FOR THE INSTALLATION OF HIS HANGERS. S. SLEEVES SHALL BE PROVIDED FOR ALL MECHANICAL PIPING PASSING THROUGH CONCRETE FLOOR SLABS AND CONCRETE, MASONRY, TILE AND GYPSUM WALL CONSTRUCTION. T. ALL INSULATION SHALL HAVE A COMPOSITE (INSULATION, JACKET OR FACING, AND ADHESIVE) FIRE HAZARD RATING AS TESTED BY ASTM E-84, NFPA 255, OR UL 723, NOT TO EXCEED 25 FLAME SPREAD & 50 SMOKE DEVELOPED. ACCESSORIES SUCH AS COATINGS, TAPES, AND ADHESIVES SHALL HAVE THE SAME COMPONENT RATINGS. ALL INSULATING MATERIALS OR THEIR CONTAINERS SHALL HAVE A LABEL INDICATING COMPLIANCE WITH THE ABOVE RATING. REFERENCE STANDARDS: NFPA D-255, A.S.T.M. E-84, UL -723, ASHRAE 90-75 AND THE STATE ENERGY CODE. ACCEPTABLE MANUFACTURERS: CERTAINTEED, OWENS-CORNING, KNAUF AND MANVILLE. U. THE CONTRACTOR SHALL PROVIDE THE OWNER WITH A COMPLETE OPERATING AND MAINTENANCE MANUAL AND ONE SET OF MYLAR REPRODUCIBLES SHOWING ALL AS -BUILT CONDITIONS. THE MANUALS SHALL INCLUDE ALL MANUFACTURER'S SPECIFICATIONS, OPERATION, MAINTENANCE, INSTRUCTIONS, WARRANTY, LOCAL SOURCE OF SUPPLY FOR SPARE PARTS AND SERVICES, ETC. V. PROVIDE WEATHER-PROOF FLASHING AT ALL DUCT, PIPE, ETC. MECHANICAL PENETRATIONS THROUGH THE BUILDING WALLS AND ROOF. FLASHING SHALL BE DESIGNED AND INSTALLED PER SMACNA AND SHALL BE GUARANTEED WEATHER PROOF FOR THE DURATION OF THE GUARANTEE. PLUMBING FIXTURE CONNECTION SCHEDULE DESIG.: ITEM: TRAP: WASTE: VENT: CW: HW: P1 WATER CLOSET 3" 3" 2" 1/2" - P3 LAVATORY 1-1/4" 1-1/2" 1-1/2" 1/2" 1/2" FD FLOOR SINK 2" 2" 1-1/2" - - [ VENT / G / GAS PIPE NOTES: (1) ALL FIXTURES SHALL COMPLY WITH THE WATER CONSERVATION ACT REQUIREMENTS. (2) COORDINATE WITH ARCHITECTURAL FOR EXACT LOCATION OF ALL PLUMBING FIXTURES. (3) NO UNDERGROUND WASTE PIPING LESS THAN 2". (4) FLOOR DRAINS SHALL HAVE TRAP PRIMERS. H.W. CIRCULATING PUMP SCHEDULE PLUMBING LEGEND HWCP-1 AND HWCP-2 SYMBOL ,DESCRIPTION SYMBOL DESCRIPTION MODEL: COLD WATER PIPE TYPE: COLD WATER CW - CiHOT WATER PIPE RPM: FILTERED WATER HOT WATER -F- - - - - OW WASTE/SOIL PIPE PHASE: HOT WATER (140T) HOT WATER RETURN -140°F - O VENT PIPE -HWR- (1) ALL BRONZE PUMP, 125 PSI MIN. RATED. [ VENT / G / GAS PIPE WASTE, SANITARY RL RAIN LEADER PIPE WASTE, GREASE GW P1 PLUMBING FIXTURE TAG RAIN LEADER RL 0 PLAN NOTE #1 GAS (±2PSIG) -MPG WH -1 WH #1 (EQUIP. TAG) GAS (7 IN-W.C.) G ® FFD' FLOOR DRAIN W/ FUNNEL CONDENSATE co LLJ FS FLOOR SINK GATE VALVE 04 :•: FD FLOOR DRAIN 7` N ` / COLD WATER PEX ®GD ' GARAGE DRAIN 7- `.. HOT WATER PEX ®PD PLANTER DRAIN [®] CW MANIFOLD PEX/WIRSBO ®DD DECK DRAIN HW MANIFOLD PEX/WIRSBO l®] ®RD/OF ROOF/OVERFLOW DRAIN 0 BALANCING/SHUT-OFF VALVE ®AD AREA DRAIN BALL VALVE El FCC FLOOR CLEANOUT mWCO WALL CLEANOUT PRESSURE GAUGE El GOO . GRADE CLEANOUT -III UNION 0.5" 1/2" PIPE SIZE -- SR SUDS RELIEF 0.75" 1" 3/4" PIPE SIZE 1" PIPE SIZE zis-R--1 RELIEF VALVE 1.25" 1-1/4" PIPE SIZE -I I I- VTR VENT THROUGH ROOF 1.5" 1-1/2" PIPE SIZE 2" 2" PIPE SIZE it VTR VENT THRU ROOF 2.5" 2-1/2" PIPE SIZE 3" 3" PIPE SIZE BURIED PIPE ,' 0- o- PIPE ELBOW UP PIPE ELBOW DOWN -- CHECK VALVE -o- PIPE TEE UP „gf_ REDUCED PRESSURE PIPE TEE DOWN RPBP BACKFLOW PREVENTER A PRV o -7e- PRESSURE REDUCING VALVE HOSE BIBB (WALL HYDRANT) H.W. CIRCULATING PUMP SCHEDULE DESIGNATION: HWCP-1 AND HWCP-2 ZONE: KITCHEN AND BATHROOM MANUFACTURER:. TACO MODEL: 110 TYPE: INLINE G.P.M.: 5 HEAD (FT -H20): 7 RPM: 1725 MOTOR: 3 -SPEED VOLTAGE: 115 PHASE: 1 WEIGHT (LBS): - REMARKS: (1) (1) ALL BRONZE PUMP, 125 PSI MIN. RATED. REVISIONS No changes sh?!l b r1 .de to the scope of work witho;.:i prior approval of Tukwila Building Division NOTE: Revisions will rquire a ns.,7 pian submittal and may include additional plan revisw fees FILE C:17-7 6 74;1r Nue /261 Lk"' Pian rsv:ciw to subject to mom and c:: !:::!e . \pproval ©f construction uction documents does not C.0 ::v iia tha violation of any adopted code or ordinance. Recopt of approved Field Copy and conditions is acknowledged: By: Data: 2./2'7'/J7 City of Tukwila BUILDING DIVISION SEPAP1 ;Tl_ Ermcchanical SEIcctrical 0 Plumbing Leas City of TPiping(`wFkwjlaf� `' BUILD3i' `, DiVISION RECEIVED JAN 2 6 2017 TUKWILA PUBLIC WORKS RECEIVED CITY OF TUKWILA JAN 242017 PERMIT CENTER REVIEWED FOR PLIANCE VED SHEET INDEX A� RC P1.0 LEGEND, GENERAL NOTES AND DETAILS t FEB 2 A P2.0 PLUMBING PLAN, DETAILS " . P3.0 SPECIFICATIONS PK.) City of T BUILDING t 2017 ukwila !VISION ABOSSEIN ENGINEERING L. L. C MECHANICAL - ELECTRICAL CIVIL - LEED - STRUCTURAL FIRE PROTECTION 2100 112TH AVE. NE BELLEVUE, WA 98004 OFFICE: (425) 462-9441 FAX: (425) 462-9451 EMAIL: CService@abossein.com WEBSITE: www.abossein.com 17450 W. VALLEY HWY TUKWILA, WASHINGTON 98188 • Cn w 0 z a 44 Cip QI w wa z wA c AL) ZU) W -to PERMIT SET DATE: 01/20/2016 JOB NO. 216152 NO. DATE REVISION Den's Law Mayou CONNECT 2" GAS TO EXISTING GAS LINE. CONTRACTOR TO VERIFY LOCATION AND SIZE OF GAS LINE BEFORE INSTALLING. COORDINATE WITH PSE FOR TOTAL METER SIZE & VERIFY SERVICE LOAD FOR NEW ADDITION Public Warks Department -Gregg Zimmerman, P.E., Administrator ABOSSEIN ENGINEERING L.L.0 Mr, Luke Vasquez General Hlanager SyKart Indoor Racing Center, LLC 11450 West Valley Highway Tukwila, WA 98188 MECHANICAL - Fi.FCTRICAL CIVIL - LEED - STRUCTURAL FIRE PROTECTION RE: PLUMBING/GAS PIPING Perrnit Application Number PG17-0014 SYIiART INDOOR RACING —17450 W VALLEY HWY CONNECT ;1 "CW TO EXISTING 1 "CW OR LARGER 2100 112TH AVE. NE BELLEVUE, WA 98004 OFFICE: (425) 462-9441 FAX: (425) 462-9451 Dear Mr, Vasquez: The City of Renton has reviewed your proposed addition of a new lounge/snack bar for the SyKart Indoor Racing center, LLC located at 17450 West Valley Highway, Based upon the proposed use, the City of Renton recommends Installing a grease trap for tills. application We suggest 070 gallon grease trap but defer to this City of Tukwila, plumbing requirements, for approval of sizing. If you have any questions regarding the City of Renton's recommendation, please contact me by phone at 42S-430-7206 or email at mbenoit0rentowa.eov. CONNECT 2)"V TO EXISTING V RISER EMAIL: CService@abossein.com MOP SINK WEBSITE: www.abossein.com LW V v 'v'..'v..L� WM/ \L' 'vv HAFi1e5y\WWP. Via steWaterjWWP-D3-1:000Cor rasp r encs K'asthwate13seSkSyl4artiirdeer.ttosImAecv 1055 South Grady Way, Renton, WA 55057 + rentotme.gov FLOW CONTROL VALVE WD Series Tag: FJ91 Cart'rl`i ld Base Interceptor SPIFCIPICA IOhN Watts Dral sa WD Sart= PDI Cere.d massed or floor mounted.paxy nolo ad Steal grease interceptor with goalceted epoxy coated lli 18kldproof cover secured with hex head canter belt(s), removable bele aassmbly, dnap seal trop with dstinout, external cast iron flaw control fiking, and no hub f skindard) g nnir.^tlons. I "-----Ili401 a C tYf#kj 1 WWI naoeon Suffix Flaw Rase i5e t One) Description Lbs 4 7 10 13 2c to 23 SO 4 ON 7 GAMh 100114 2s nedS 23O M 23 OM ID ON E C C G C 8 1 Hem SUWLX Options ISetect One Mare) Description a -lc bD 0 SMD 410 Raw 8 Cry tames nosi12Jtftl7,bs)T 1i. ee' W elP><tftkw al Uee d,d :osmcisra h, C c ` E E 126MBH TO MAKE UP M AIR UNIT FOR KITCHEN — — i — — CONTRACTOR—TO VERIFY LOCATION AND SIZE BEFORE INSTALLING (568CFH)/ " (105CFH) (343CFH) i Number Rote Lbs se BoCenter T err 8 1 Hem WD4 4 a 2'S) 74d4'i107/ mien 18+1428 irects51 1I'271 W2.7 7 Id 2';S`) 3l/2'i716) 3i/2'13p) 1a+14371 is,os0i 12'325) va2.13 10 70 3';3') 3.1/2•)718) 34/7'511 418/4'1932 141Si) 174222) W015 13 70 VA') 104/2'1 ) i.1/'3'1 22 t#S9j 1S '2$1) ids '40000 23 40 7'784 11.11l'10 7 3.1/:++20) :vista 1S2/4'j4L3 12' 2a') W1313 :3 so Tye tram blf7';1.41 :i'i38a 1a1/a'14ip1 16.1/a't$r8J WD.13 33 70 3'761 tease) 3';137) 32'82 111'14373 14'$483) 100 I rilDM 11 91400) 3.1.12. 11,22 321113/ 22 157) 214/313461 Win Ttu Msrrrada, cortalrai WI- le rink i sIdad in rapt= tie *11 Domini Irek!I and iskti ai o 2o1 'Wade a tin siQsder ce sf as talali preatet Mar, bob k lig RIa hi 211 pVf"`t^ t. t (105CFH) 1.25" (238CFH) Job Same Contractor Job LocsiIon Contra:tor's P.C. No. Engineer AamDMA ramrr22memlLti =innAMIN Millaaf a-arrsara,4kotatarielItir.Fir nubs miasrrnada3snemixt lExanemgal says.l rstan,smrNllmamrt.xnsav7pedalM . ditd31324131.1piddS2131, MUNI ri&Hsi few Mei fel 1t2Ls'rMad a';a7121011le IUD Ldi re trnoMsWan mix* Dr attinsdanIDdG IJ5h iii: ono 350,4531 a Fan 3. #LM22 . Yattaoam A Watts water 7brhnnlppks Company Oman Dr (20. 2324030+ Fax o35i 032.7325 ■ Wsasna WWI Aauala3: i>it' T,' 51.12314= 2 Fal P;~ 121-1000-M21 • Wady= ®•W2-WDSERIES LEA 11342 22015 Watts NEW T.I. FLOOR PLAN - PLUMBING SCALE: 1/4'-1'-0' RECEIVED CITY OF TUKWILA FEB 2 1 2017 2" VENT, ROUTE IN WALL BRACKET MANIFOLD TO WALL, 18" ON CENTERS GAS MANIFOLD. SEE PLAN OR RISER FOR SIZE GAS SHUTOFF VALVE FOR EACH PIECE OF EQUIPMENT BY CONTRACTOR EQUIPMENT CONNECTION. VERIFY SIZE WITH EQUIPMENT SUPPLIER VENTED WASTE GREASE TRAP FLOW CONTROL FITTING WITH UNIONS FOR REMOVAL AND SERVICE FLOW Il�l•lil PERMIT CENTER 90' ELBOW CONTRACTOR SHALL PROVIDE AND INSTALL DORMONT, HOSEMASTER (OR EQUAL) QUICK DISCONNECTS AND HORIZONTAL LOOP SMARTSWIVELS, FLEXIBLE GAS CONNECTOR AND A RESTRAINING DEVICE FOR EACH PIECE OF EQUIPMENT. SEE PLAN OR RISER FOR SIZE REGULATOR W/VENT TO OUTSIDE (OR VENTLESS REGULATOR PER LOCAL JRSD.) NOTE: SEE PLANS FOR SIZE AND REQUIREMENTS GAS PIPING DROP AND SHUTOFF VALVE GAS SOLENOID VALVE AND BY—PASS-----.. INTERCONNECT VV/HOOD EXHAUST FANS FURNISHED BY HOOD SUPPLIER, INSTALLED BY PLUMBING CONTRACTOR. BYPASS PIPING IF REQUIRED INDIRECT WASTE '0 X 2 MIN. AIRGAP FINISHED FLOOR FLOW CONTROL ASSEMBLY WALL FACE BEHIND EQUIPMENT FULL SIZE DIRT LEG (6" MIN.) WITH THREADED CAP. INSTALL WITH AMPLE CLEARANCE TO REMOVE CAP. GREASE TRAP DETAIL SCALE: NONE DIRT LEG DETAIL FURNISH AND INSTALL A 1/4 TURN MANUAL SHUTOFF VALVE IN AN ACCESSIBLE LOCATION OR AS REQUIRED BY CODE. GROUT AND FLOORING BAS FLOOR SINK SHALL BE EASILY AND FULLY ACCESSIBLE FOR CLEANING. MOUNT FLOOR SINK FLUSH TO FINISHED FLOOR ONLY AT THE CUSTOMER SIDE. RAISE FLOOR SINK PER DETAIL ABOVE AT THE OPERATION SIDE. REVIEWED F CODE COMPLIAi CE APPROVED HALF EXPO D ''''pp 5 GR0F B IPD4AT2�11 / & FINISHED FLOOR City of Tukwil f jI DING DIVI' 0.25". �)I„ ilei I.- FLOOR TROUGH/GRATE FLUSHED WiTH FINISHED FLOOR PERMIT SET DATE: 01/20/2016 JOB NO. 216152 2/17/17 REVISION GREASE TRAP GREASE HOOD AUTO GAS SHUTOFF NO SCALE NO SCALE NO SCALE NO SCALE li SPECIFICATIONS PLUMBING SPECIFICATIONS - DIVISION #22 PART 1.00 GENERAL 1.01 LOCAL CONDITIONS: VISIT AND INSPECT THE PREMISES TO ASCERTAIN THE EXISTING CONDITIONS BEFORE SUBMITTING A BID. NO EXTRA PAYMENT WILL BE ALLOWED FOR THE LACK OF KNOWLEDGE OF THESE CONDITIONS. 1.02 CODES: STRICTLY COMPLY WITH ALL APPLICABLE LOCAL, STATE, AND FEDERAL CODES AND REGULATIONS. IMC - Mechanical Code - 2012 UPC - Plumbing Code - 201.2 PCC - WASHINGTON STATE ENERGY CODE -COMMERCIAL WASHRAE 1.03 STANDARDS: THE FOLLOWING PUBLICATIONS (LATEST EDITION) FORM A PART OF THESE REQUIREMENTS TO THE EXTENT INDICATED BY THE REFERENCES THERETO: NFPA PAMPHLET 54 NFPA PAMPHLET 90A 1.04 PLANS AND SPECIFICATIONS: THE PLUMBING DRAWINGS ARE DIAGRAMMATIC IN CHARACTER INTENDED TO CONVEY THE SCOPE OF WORK AND INDICATE THE GENERAL ARRANGEMENT OF EQUIPMENT, PIPING, ETC., AND APPROXIMATE SIZES AND LOCATIONS OF EQUIPMENT AND OUTLETS. DETERMINE THE EXACT LOCATION OF THE ELEMENTS OF THE SYSTEM FROM STRUCTURE AND FROM THE EQUIPMENT, NOT FROM THE DRAWINGS. DO NOT SCALE DRAWINGS FOR MEASUREMENTS NOR USE AS SHOP DRAWINGS. 1.05 PROVIDE ALL ITEMS, EQUIPMENT, MATERIALS, OPERATIONS, OR METHODS LISTED, MENTIONED OR SCHEDULED ON THE DRAWINGS, AND/OR HEREIN INCLUDING ALL INCIDENTALS AND ACCESSORIES NECESSARY AND REQUIRED FOR INSTALLATION OR MOUNTING, OR NORMALLY SUPPLIED BY COMMON PRACTICE WHETHER SPECIFICALLY MENTIONED OR NOT, TO PROVIDE COMPLETE AND PROPERLY FUNCTIONING SYSTEMS. 1.06 BRING ANY NON -COMPLIANCES WITH ALL APPLICABLE LOCAL, STATE AND FEDERAL CODES AND REGULATIONS, CONFLICTS AND DISCREPANCIES TO THE ENGINEER'S ATTENTION BEFORE SUBMITTING BID. A CORRECT, COMPLETE AND EASILY MAINTAINED SYSTEM IS INTENDED. 1.07 THE CONTRACTOR'S BID WILL BE CONSTRUED AS AN AGREEMENT TO COMPLETE THE WORK WITHOUT ADDITIONAL COST TO THE OWNER. WHERE CONFLICTS BETWEEN PLANS AND SPECIFICATIONS OR CONFLICTING INFORMATION ON THE PLANS OCCURS, THE CONFLICTS SHALL BE REPORTED TO THE ARCHITECT PRIOR TO BIDDING. THE MORE COSTLY ALTERNATIVE SHALL BE INCLUDED IN THE BID PRICE. 1.08 MAKE NO CHANGES IN THE WORK SPECIFIED, UNLESS SUCH CHANGES ARE AUTHORIZED IN WRITING BY THE OWNER, ARCHITECT AND/OR ENGINEER. NO CHARGES FOR EXTRA WORK WILL BE PAID UNLESS SUCH EXTRA WORK HAS BEEN AUTHORIZED AND THE AUTHORIZATION CONTAINS A STATEMENT OF THE WORK TO BE ACCOMPLISHED AND THE CHARGES TO BE MADE FOR THE WORK. 1.09 THE INFORMATION PRESENTED ON THESE DRAWINGS IS DIAGRAMMATIC IN NATURE. IT DOES NOT NECESSARILY REPRESENT ALL FITTINGS, HANGERS, ETC. REQUIRED FORA COMPLETE WORKING SYSTEM. PROVIDE ALL MATERIALS AND LABOR FOR COMPLETELY FINISHED AND OPERATIONAL SYSTEMS. 1.10 REFER TO LATEST ARCHITECTURAL DRAWINGS FOR: EXACT WALL LOCATIONS, DIMENSIONS, AND PLUMBING FIXTURE LOCATIONS AND REQUIREMENTS. 1.11 CONTRACTOR SHALL NOTIFY THE ENGINEER OF ANY ALTERATIONS REQUIRED BY THE OWNER, ARCHITECT, OR FIELD CONDITIONS. 1.12 ALL EQUIPMENT SHALL BE NEW, SHALL COMPLY WITH SPECIFICATIONS ON DRAWINGS, AND SHALL COMPLY WITH ENERGY CONSERVATION CODE REQUIREMENTS AS ADOPTED BY THE STATE, AS WELL AS LOCAL JURISDICTIONAL WITHDING N. SUBMIT DATA FOR APPROVAL PRIORATO ORDERING ING STATE, SITTOL SHALL INCLUDE ENERGY CODE COMPLIANCE CERTIFICATION. 1.13 THE CONTRACTOR SHALL REFER TO ALL OTHER DRAWINGS, INCLUDING: ARCHITECTURAL, STRUCTURAL, MECHANICAL, ELECTRICAL, AND FOOD SERVICE, FOR ALL COORDINATION AND REFERENCE DATA. COORDINATE INSTALLATION WITH WORK OF OTHER TRADES. 1.14 DURING BID PERIOD: INVESTIGATE AND VERIFY EXISTING CONDITIONS, EXACT LOCATIONS, ELEVATIONS, AND CHARACTERISTICS OF EXISTING UTILITIES AND PIPING. BRING ANY DISCREPANCIES TO ATTENTION OF ARCHITECT AS SOON AS POSSIBLE. 1.15 REVIEW ELECTRICAL LAYOUT, ROUTING OF UNDERGROUND ELECTRICAL UTILITIES INCLUDING POWER AND TELEPHONE, NEW AND EXISTING UNDERGROUND ELECTRICAL CONDUIT LINES, PRIOR TO START OF WORK. 1.16 CONSULT WITH ALL TRADES AND DETERMINE EXTENT OF PLUMBING WORK DURING BID PERIOD. EXTEND ALL SERVICES TO LOCATIONS DESIGNATED AND REQUIRED, FURNISH ALL MATERIALS, AND PAY ALL COSTS NOT FURNISHED BY OTHERS. 1.17 IT IS THE INTENT OF THESE SPECIFICATIONS TO PROVIDE A MECHANICAL SYSTEM COMPLETE, FULLY ADJUSTED, AND READY FOR OWNER'S BENEFICIAL USE. 1.18 IT IS THE INTENTION OF THESE SPECIFICATIONS AND DRAWINGS TO CALL FOR FINISHED WORK, TESTED, AND READY FOR OPERATION. WHEREVER THE WORD "PROVIDE" IS USED, IT SHALL MEAN "FURNISH AND INSTALL COMPLETE AND READY TO USE."MINOR DETAILS NOT USUALLY SHOWN OR SPECIFIED, BUT NECESSARY FOR THE PROPER INSTALLATION AND OPERATION, SHALL BE INCLUDED IN THE WORK, THE SAME AS IF HEREIN SPECIFIED OR SHOWN. 1.19 THE CONTRACTOR SHALL GIVE ALL NECESSARY NOTICES, OBTAIN ALL PERMITS AND PAY ALL GOVERNMENT SALES TAXES, FEES AND OTHER COSTS, INCLUDING UTILITY CONNECTIONS OR EXTENSIONS, IN CONNECTION WITH HIS WORK; FILE ALL NECESSARY PLANS, PREPARE ALL DOCUMENTS AND OBTAIN ALL NECESSARY APPROVALS OF ALL GOVERNMENTAL DEPARTMENTS HAVING JURISDICTION; OBTAIN ALL REQUIRED CERTIFICATES OF INSPECTION OF HIS WORK AND DELIVER SAME TO THE ARCHITECT BEFORE REQUEST FOR ACCEPTANCE AND FINAL PAYMENT FOR WORK. 1.20 THE CONTRACTOR SHALL INCLUDE IN THE WORK, WITHOUT EXTRA COST TO THE OWNER, ANY LABOR, MATERIALS, SERVICES, APPARATUS, DRAWINGS, IN ORDER TO COMPLY WITH ALL APPLICABLE LAWS, ORDINANCES, RULES ANDOF REGULATIONS, WHETHER OR NOT SHOWN ON DRAWINGS AND/OR SPECIFIED. PART 2.00 PRODUCTS 2.01 MATERIALS AND EQUIPMENT SUBSTITUTIONS: THE BID PRICE SHALL BE BASED ON THE MATERIALS, EQUIPMENT AND/OR SERVICES AS SCHEDULED ON THE DRAWINGS AND/OR SPECIFIED HEREIN, AND/OR AS ACCEPTED PRIOR TO BIDDING.MOISTURE 2.02 ACCEPTANCE OF ALTERNATE OR SUBSTITUTE EQUIPMENT IN NO WAY VOIDS MATERIAL OR PERFORMANCE REQUIREMENTS. THE CONTRACTOR SHALL BE RESPONSIBLE FOR THE PERFORMANCE OF PER MATERIAL OR FOR SPECIFIED ITEMS ACCEPTED BY THE ARCHITECT AND/OR ENGINEER BEFORE OR EQUIPMENTP THE SUBSTITUTEDBID TU. CONTRACTORORSPE SHALL BE RESPONSIBLE FOR INCORPORATING TIND ANY SUBSTITUTE FOR EQUIPMENT AFTEIN THE SYSTEM DESIGN. 2.03 CONTRACTOR SHALL PAY FOR ALL EXTRA COSTS BY ANY TRADE FOR CHANGES NECESSITATED BY MATERIAL OR EQUIPMENT SUBSTITUTIONS REGARDLESS OF ACCEPTANCE WITHOUT FURTHER COST TO THE CLIENT. I 2.04 DOMESTIC WATER PIPING ABOVE GROUND SHALL BE TYPE "L" HARD DRAWN COPPER WITH WROUGHT COPPER FITTINGS OR PEX. JOINTS AND CONNECTIONS SHALL BE COMPLETED WITH 95 PERCENT TIN, 5 PERCENT ANTIMONY OR PEX JOINTS. NON-METALLIC PVC "GOLD" (OR EQUAL) MAY BE USED IN -LIEU OF COPPER PIPING IF ITEMIZED AS A "DEDUCT" IN BID AND SUBMITTED FOR THE' OWNER'S CONSIDERATIONS. 2.05 WATER PIPING BELOW GROUND SHALL BE TYPE "K", NON-METALLIC PVC PIPING MATERIAL AS APPROVED PER THE IAPMO AND LOCAL JURISDICTION SHALL BE ACCEPTABLE' 2.06 WASTE AND VENT PIPING SHALL BE SERVICE WEIGHT CAST IRON SOIL PIPE WITH NO HUB FITTINGS. PVC OR APPROVED ABS NON-METALLIC PIPING SHALL BE IN ACCORDANCE WITH THE INTERNATIONAL PLUMBING CODE. ALTERNATES SHALL BE SUBMITTED OWNER AND APPROVED BY THE BUILDING THE INT DEPARTMENT PRIOR PO START CO WORK. ALTERNATES IT PIPING MAY USED FOR UNDERGROUND HOWEVERYTHE ABOVE GROUND PIPING(AND PROPERLY FIRE STOPPED)WHERE APPROVED BY LOCAL JURISDICTION SHALL BE ITEMIZED "DEDUCT" IN BID FOR OWNER'S CONSIDERATIONS. 2.07 INSULATE ALL PIPING, VALVES, AND FITTINGS FOR DOMESTIC COLD, HOT AND RECIRC. LINES WITH (1/2" CW, 1" HW & RECIRC) PRE -FORMED FIBERGLASS INSULATION WITH "K" FACTOR OF 0.30 MAXIMUM AT 200 deg. F. MEAN TEMPERATURE. PROVIDE ALL SERVICE, SELF LAP JACKET, AND VAPOR BARRIER. INSULATE CONDENSATE DRAINS W/\" ARMAFLEX #22 OR "JM" AEROTUBE INSULATION. PROVIDE ADDITIONAL INSULATION IN AREAS SUBJECT TO FREEZING. SEE SPECIFICATION FOR TRACED -LINE INSULATION. 2.08 NO STRUCTURAL MEMBERS SHALL BE CUT WITHOUT THE APPROVAL OF THE ARCHITECT, AND ALL SUCH CUTTING SHALL BE DONE IN A MANNER DIRECTED BY HIM/HER. 2.09 PROVIDE WEATHERPROOF FLASHING AT ALL DUCT, PIPE, ETC., MECHANICAL PENETRATIONS THROUGH THE BUILDING WALLS AND ROOF. FLASHING SHALL BE DESIGNED AND INSTALLED PER SMACNA AND SHALL BE GUARANTEED WEATHER PROOF FOR THE DURATION OF THE GUARANTEE. 2.10 ALL INSULATION SHALL HAVE A COMPOSITE (INSULATION, JACKET OR FACING, AND ADHESIVE) FIRE HAZARD RATING AS TESTED BY ASTM E-84, NFPA 255, OR UL 723, NOT TO EXCEED 25 FLAME SPREAD AND 50 SMOKE DEVELOPED. ACCESSORIES SUCH AS COATINGS, TAPES, AND ADHESIVES SHALL HAVE THE SAME COMPONENT RATINGS. ALL INSULATING MATERIALS OR THEIR CONTAINERS SHALL HAVE A LABEL INDICATING COMPLIANCE WITH THE ABOVE RATING. REFERENCE STANDARDS: NFPA D-255, A.S.T.M. E-84, UL -723, 90-75 AND THE STATE ENERGY CODE (IF APPLICABLE). ACCEPTABLE MANUFACTURERS: CERTAINTEED, OWENS-CORNING, KNAUF AND MANVILLE. 2.11 PIPE MATERIAL: COLD WATER AND HOT WATER COPPER "L" (LEAD FREE) WASTE AND VENT CAST IRON (ABOVE GRADE) NOTE: JOINTS AND METHOD OF CONNECTIONS SHALL BE PER THE IPC -CHAPTER 13, ASTM STANDARDS AND MANUFACTURERS RECOMMENDATIONS FOR EACH PIPE TYPE AND APPLICATIONS. 2.12 PIPE INSULATION: COLD WATER - 1/2" INSULATION WITH VAPOR BARRIER JACKETS. HOT WATER - 1" INSULATION FOR ALL PIPING UP TO 2" DIAMETER. UNDERGROUND PIPING WITH 1" CLOSED CELL FOAM INSULATION. UNLESS NOTED OTHERWISE PART 3.00 EXECUTIONS 3.01 PERMITS AND INSPECTIONS: APPLY AND PAY FOR ALL PERMITS AND CERTIFICATES OF INSPECTION REQUIRED FOR THE WORK, AND AT COMPLETION, PRESENT THE OWNER WITH THE SIGNED CERTIFICATES OF FINAL INSPECTION. 3.02 UTILITIES: CHARGES BY UTILITY COMPANIES FOR PROVIDING SERVICES SHALL BE PAID BY OWNER AND WILL NOT BE A PART OF THIS CONTRACT. THE CONTRACTOR SHALL DO INSTALLATION WORK NORMALLY PROVIDED IN THIS CONTRACT. 3.03 PLACE AND ARRANGE EQUIPMENT, PIPING, CONTROLS, ETC., TO FIT THE SPACE AVAILABLE. INCLUDING ALL OFFSETS IN PIPING, ETC. REQUIRED. 3.04 THE ENGINEER'S CHECK SHALL BE GENERAL, AND DOES NOT RELIEVE THE CONTRACTOR OF FINAL RESPONSIBILITY OF COMPLIANCE TO THE INTENT OF THE PLANS AND SPECIFICATIONS. 3.05 SUPERVISION AND WORKMANSHIP: QUALIFIED SUPERVISION FOR EACH TRADE SHALL BE IN CHARGE OF THE WORK AT ALL TIMES AND SHALL BE ON THE JOB SITE WHENEVER WORK IN THAT TRADE IS BEING ACCOMPLISHED. 3.06 ALL WORK SHALL BE DONE IN A FIRST-CLASS MANNER BY WORKMEN SKILLED IN THE TRADE AFFECTED. 3.07 CLEANING PIPING &EQUIPMENT, TESTING: PLUG ALL NECESSARY OPENINGS OF THE ENTIRE DRAINAGE AND VENTING SYSTEM TO PERMIT THE COMPLETE SYSTEM OR PORTION THEREOF TO BE FILLED WITH WATER TO THE LEVEL OF THE HIGHEST VENT STACK ABOVE THE ROOF ORA VERTICAL STACK MAY BE FILLED WITH WATER TOA HEIGHT OF 10 FT. ABOVE THE HIGHEST HORIZONTAL RUN TO BE TESTED. THE SYSTEM SHALL MAINTAIN THE WATER LEVEL WITHIN 1 IN. WHEN TESTED FOR 30 MIN. WHEN AN AIR TEST IS USED, APPLY A PRESSURE OF NOT LESS THAN 5 PSI WITH A FORCE PUMP AND MAINTAIN AT LEAST 15 MINUTES WITHOUT LEAKAGE WHEN TESTED WITH A MERCURY COLUMN GAUGE. 3.08 CLEAN ALL EQUIPMENT, PIPE, VALVES AND FITTINGS OF GREASE, METAL CUTTINGS, DIRT AND SLUDGE THAT MAY HAVE ACCUMULATED BY OPERATION OF THE SYSTEM FOR TESTING. REPAIR ANY STOPPAGE OR DAMAGE TO PARTS OF THE BUILDING, TO IT'S FINISH OR FURNISHINGS DUE TO THE CONTRACTOR'S FAILURE TO PROPERLY CLEAN THE PIPING SYSTEM WITHOUT COST TO THE OWNER. ADJUST THE HOT WATER SYSTEM FOR UNIFORM FLOW. ADJUST FLUSH VALVES AND OTHER PARTS OF THE SYSTEM FOR QUIET OPERATION. AFTER CLEANING THE POTABLE WATER SYSTEM, OR PART THEROF, FILL WITH A SOLUTION CONTAINING 50 PARTS PER MILLION OF AVAILABLE CHLORINE AND ALLOW TO STAND FOR SIX (6) HOURS BEFORE FLUSHING. 3.09 COMPLETION: OPERATE ALL PLUMBING SYSTEMS, INCLUDING ALL EQUIPMENT FURNISHED UNDER THIS DIVISION TO PROVE THAT ALL COMPONENTS ARE PROPERLY OPERATING AND THAT THE COMPLETE INSTALLATION IS FUNCTIONING SMOOTHLY AND NOISELESSLY TO THE FULL EXTENT OF PLANS AND SPECIFICATIONS. ANY REBALANCING, READJUSTING OF SYSTEM ELEMENTS FOUND NECESSARY WHEN THE SYSTEMS ARE SUBJECT TO ACTUAL OPERATING CONDITIONS SHALL BE DONE BY THE CONTRACTOR AT NO EXTRA COST TO THE OWNER. 3.10 OPERATING INSTRUCTIONS: PROVIDE TYPEWRITTEN OPERATING INSTRUCTIONS IN THE BROCHURE COVERING EACH PIECE OF PLUMBING EQUIPMENT, GIVE NORMAL STARTING AND STOPPING PROCEDURES, ALONG WITH PROPER PARTIES TO CONTACT IN THE EVENT OF EMERGENCY, FAILURE OF EQUIPMENT. OUTLINE OF INSTRUCTIONS AS FOLLOWS: 3.11 AS -BUILT DRAWINGS: SUBMIT AS -BUILT DRAWINGS AT COMPLETION OF WORK TO OWNER. 3.12 GUARANTEE: THE PLUMBING SYSTEM SHALL BE LEFT IN PROPER WORKING ORDER. REPLACE ANY WORK, MATERIAL OR EQUIPMENT PROVIDED UNDER THIS CONTRACT WHICH DEVELOPS DEFECTS WITHIN ONE (1) YEAR FROM DATE OF SUBSTANTIAL COMPLETION WITHOUT ADDITIONAL CHARGES. A NEW ONE (1) YEAR GUARANTEE ON THE AFFECTED ITEM OR ITEMS SHALL BE PROVIDED COMMENCING ON THE DATE OF THE APPROVED REPAIR OR REPLACEMENT. 3.13 CUTTING AND PATCHING: CAREFULLY PERFORM ALL WORK WHERE CUTTING, CHANNELING, CHASING, OR DRILLING OF FLOORS, WALLS, PARTITIONS, CEILINGS OR OTHER SURFACES IS NECESSARY FOR PROPER INSTALLATION OR SUPPORT OF PIPING, OR OTHER PLUMBING EQUIPMENT. 3.14 ANY DAMAGE TO BUILDING, PIPING, EQUIPMENT, PLASTER, WOODWORK OR METAL WORK SHALL BE REPAIRED BY SKILLED MECHANICS OF TRADES INVOLVED, AT NO ADDITIONAL COST TO THE OWNER. 3.15 DO NOT CUT, CHANNEL, CHASE OR DRILL MASONRY OR TILE; OR CUT, DRILL OR WELD STRUCTURAL MEMBERS THE BUILDING, ETC., WITHOUT FIRST OBTAINING OWNER'S PERMISSION, IF PERMISSION IS GRANTED, PERFORM THIS WORK IN A MANNER APPROVED BY THE OWNER. 3.16 CAULKING & WATERPROOFING: CAULK AROUND ALL PIPES, ETC. TO PREVENT AIR AND MOISTURE LEAKAGE WITH COMPOUND APPROVED BY ARCHITECT/ENGINEER. 3.17 PROVIDE FLASHINGS WHERE ALL PIPES PIERCE OUTSIDE WALLS OR ROOF AS NECESSARY TO PREVENT ENTRY. 3.18 INSERTS, SLEEVES & BLOCKOUTS: FURNISH AND INSTALL, PRIOR TO CONCRETE POURING OR OTHER CONSTRUCTION, INSERTS, SLEEVES, OR BLACKOUTS IN WALLS, FLOOR SLABS, ROOFS AND PARTITIONS FOR PASSAGE OF ALL WORK INSTALLED UNDER THIS DIVISION. 3.19 PROVIDE GALVANIZED IRON AND STEEL PIPE SLEEVES FOR IRON PIPES. USE COPPER SLEEVES FOR COPPER PIPES. PROVIDE WOOD OR STEEL BLACKOUTS FOR LARGE OPENINGS. SECURE ALL SUCH ITEMS FIRMLY IN POSITION. 3.20 TRENCHING AND BACKFILLING: PERFORM ALL TRENCHING AND BACKFILLING REQUIRED BY WORK PERFORMED UNDER THIS DIVISION. TRENCHING AND BACKFILLING DONE IN ACCORDANCE WITH "EXCAVATING AND GRADING" SPECIFICATIONS AND AS HEREIN SPECIFIED. TRENCHES SHALL BE EXCAVATED TO THE DEPTH REQUIRED FOR THE UTILITIES INVOLVED. THE TRENCH BOTTOM SHALL BE FREE FROM STONES OR SOFT SPOTS. 3.21 BACKFILLING PIPING TRENCHES AS SOON AS PIPING IS TESTED AND APPROVED BY THE OWNER AND BUILDING INSPECTOR. BACKFILL FOR A DEPTH OF 12 IN. OVER THE TOP OF THE PIPING WITH SAND, OR CLEAN EARTH OF SPECIFIED BACKFILL MATERIAL. UNIFORMLY PLACE AND TAMP BACKFILL BY APPROPRIATE METHODS TO ENSURE PROPER ALIGNMENT OF PIPING TO AVOID INJURY TO THE INSTALLED MATERIALS. 3.22 GRADE THE BOTTOM OF TRENCHES TO SECURE THE REQUIRED FALL WITH A UNIFORM PITCH AND ADEQUATE WIDTH TO ENSURE PROPER INSTALLATION OF PIPING. REMOVE DIRT UNDER CAST IRON HUBS SO THAT THE ENTIRE PIPE BARREL RESTS ON FIRM EARTH. BRING OVER -EXCAVATED OR INADEQUATELY COMPACTED GROUND TO THE PROPER LEVEL WITH GRAVEL. 3.23 ACCESS DOORS AND PANELS: FURNISH AND INSTALL ACCESS DOORS OR PANELS AS SHOWN ON THE DRAWINGS AND/OR AS REQUIRED FOR PROPER ACCESS TO ALL CONCEALED EXPANSION JOINTS, VALVES, ETC. IF ACCESS DOOR OR SIZE IS NOT SHOWN, PROVIDE A SIZE APPROPRIATE TO THE CONDITIONS, BUT IN NO CASE LESS THAN 12 IN. X 12 IN. 3.24 PIPING INSTALLATION: ARRANGE AND INSTALL PIPING APPROXIMATELY AS INDICATED, STRAIGHT, PLUMB AND AS DIRECT AS POSSIBLE. FORM RIGHT ANGLES OR PARALLEL LINES WITH BUILDING WALLS. PRIOR TO INSTALLATION, CHECK MECHANICAL DRAWINGS, ARCHITECTURAL, STRUCTURAL, AND ELECTRICAL DRAWINGS FOR INTERFERENCES. WHERE DEPARTURES FROM INDICATED ARRANGEMENTS ARE REQUIRED, VERIFY PROPOSED CHANGES WITH THE ARCHITECT/ENGINEER BEFORE PROCEEDING. COORDINATE WITH ALL TRADES SO THAT PIPES, CONDUITS, DUCTS, ETC., WILL NOT INTERFERE WITH EACH OTHER. 3.25 CUT PIPES ACCURATELY TO MEASUREMENT ESTABLISHED AT THE BUILDING, AND WORK INTO PLACE WITHOUT SPRINGING OR FORCING. PROPERLY CLEAR ALL WINDOWS, DOOR AND OTHER OPENINGS. MAKE CHANGES IN DIRECTION WITH FITTINGS. WHERE CHANGES IN PIPE SIZES OCCUR, USE ONLY REDUCING FITTINGS. CAP AND/OR PLUG OPEN ENDS OF PIPELINES AND OTHER EQUIPMENT DURING INSTALLATION TO KEEP DIRT OR OTHER FOREIGN MATERIAL OUT OF THE SYSTEM. INSTALL HORIZONTAL PIPING AS HIGH AS POSSIBLE WITHOUT SAGS OR HUMPS. KEEP PIPES CLOSE TO WALLS, PARTITIONS, CEILINGS, OFFSET ONLY WHERE NECESSARY TO FOLLOW WALLS AS DIRECTED. LOCATE GROUPS OF PIPES PARALLEL TO EACH OTHER. SPACE PIPING AT DISTANCES TO PERMIT APPLYING FULL INSULATION AND TO PERMIT ACCESS FOR SERVICING VALVES. 3.26 CONCEAL ALL PIPING IN BUILDING CONSTRUCTION OR UNDERGROUND IN FINISHED AREAS. THE PIPING INSTALLATION SHALL NOT CAUSE DELAY IN THE WORK OF OTHER TRADES. ALLOW AMPLE TIME FOR TESTS AND APPROVAL. KEEP FIXTURE BRANCHES CONCEALED TO POINTS ABOVE FLOOR CLOSE TO FIXTURES. EXPOSED PIPE SHALL BE CHROME PLATED. INSTALL CHROMIUM PLATED WALL AND CEILING PLATES ON ALL PIPES PASSING THROUGH WALLS, PARTITIONS, AND FLOORS WHEREVER PIPING IS EXPOSED IN FINISHED PARTS OF THE BUILDING. 3.27 PROVIDE UNIONS OR FLANGES TO ALLOW REMOVAL OF EACH PIEC TO EQUIPMENT OR CONTROL DEVICE. LOCATE BETWEEN SHUT-OFF AND EQUIPMENT. 3.28 LOCATE PIPE SUPPORT HANGERS SPACED ON STRAIGHT RUNS NOT TO EXCEED 6 FT. FOR SIZES UP TO 1-1\2" AND NOT TO EXCEED 10 FT. FOR SIZES 2" AND LARGER. 3.29 PROVIDE LINE SIZE VALVES WHERE INDICATED. VALVES IN HORIZONTAL LINES SHALL BE INSTALLED WITH STEMS HORIZONTAL OR ABOVE THE LINE. ISOLATION VALVES SHALL BE INSTALLED IN WATER LINES CONNECTED TO EACH PIECE OF EQUIPMENT AND AT ANY OTHER POINTS INDICATED. 3.30 JOINTS TAPERED THREADS OF SCREW JOINTS SHALL BE PROPERLY CUT. SEAL SCREWS JOINTS WITH AN APPROVED PIPE JOINT COMPOUND OR TAPE APPLIED TO THE PIPE THREADS AND NOT THE FITTING. 3.31 CUT COPPER TUBING SQUARE AND REMOVE BURRS. CLEAN BOTH INSIDE OF FITTINGS AND OUTSIDE OF TUBING WITH STEEL WOOL BEFORE SWEATING. DO NOT ANNEAL FITTINGS AND TUBING WHEN MAKING CONNECTIONS. USE COMPOSITION LEAD FREE SOLDER FOR ALL JOINTS. 3.32 FIXTURE INSTALLATION: PROVIDE ALL HANGERS NECESSARY TO PROPERLY SECURE FIXTURES TO THE TYPE OF CONSTRUCTION USED. COVER ALL FIXTURES WITH MANILLA PAPER. DO NOT REMOVE UNTIL COMPLETION OF THE WORK. INSTALL SUCH GUARDS AND BOXING AS NECESSARY TO PROTECT FIXTURES AGAINST DAMAGE DURING CONSTRUCTION. PROVIDE STOPS ON THE SUPPLY PIPING TO EACH FIXTURE WHETHER SPECIFIED OR NOT. PROVIDE UNIONS AT EACH FIXTURE TO PERMIT REMOVAL OF THE FIXTURE FOR REPAIR OR REPLACEMENT. ALL EQUIPMENT SHALL BE MOUNTED IN ACCORDANCE WITH MANUFACTURER'S ROUGH -IN MEASUREMENTS UNLESS OTHERWISE NOTED ON THE DRAWINGS. SEAL WATERTIGHT THE JUNCTURE OF A FIXTURE AND THE FLOOR OR WALL. 3.33 PROVIDE VACUUM BREAKERS AND BACK FLOW PREVENTORS AS NECESSARY TO AVOID WATER BEING DRAWN BACK INTO THE WATER -SUPPLY PIPING. INSTALLATION SHALL BE IN FULL COMPLIANCE OF THE REQUIREMENTS OF THE BUILDING DEPARTMENT AND THE LOCAL HEALTH DEPARTMENT. PROVIDE SHOCK ABSORBERS IN THE PIPING SYSTEM AS NECESSARY TO PRECLUDE A WATER HAMMER PROBLEM WITH THE PIPING SYSTEM. 3.34 GAS PIPING INSTALLATION: INSTALLATION SHALL CONFORM TO THE REQUIREMENTS OF NFPA PAMPHLET 54 AND TO LOCAL CODES. PROVIDE A GAS COCK AND UNION AT EACH APPLIANCE AND AT THE BULDING ENTRY. 3.35 PIPE INSULATION: INSULATE ALL HOT, COLD, AND RECIRCULATION PIPING, AS WELL AS ALL FITTINGS AND VALVES, WITH GLASS FIBER INSULATION. NOT REQUIRED FOR RUNOUTS TO FIXTURES, RISERS FEEDING FIXTURES, UNIONS, FLANGES, STRAINERS, FLEXIBLE CONNECTIONS OR EXPANSION JOINTS. APPLY ON PIPING OVER CLEAN AND DRY SURFACES WITH EDGES FIRMLY BUTTED TOGETHER. MAKE CONTINUOUS THROUGH SLEEVES OR OPENINGS IN WALL AND FLOORS. FINISH INSULATION NEATLY AT HANGERS AND SUPPORTS. FOR FITTINGS, PROVIDE ONE COAT CEMENT, PRE -MOLDED GLASS FIBER FITTING COVER AND FINISH WITH GLASS FABRIC EMBEDDED IN FIRE RETARDANT MASTIC. 3.36 KITCHEN EQUIPMENT CONNECTION REQUIREMENTS: PLUMBING CONTRACTOR SHALL PROVIDE ALL ROUGH -IN AND FINAL CONNECTIONS FOR ALL FOOD AND BEVERAGE SERVICE EQUIPMENT. 3.37 PLUMBING CONTRACTOR SHALL ALLOW INSTALLATION OF VALVES, FITTINGS, TRAPS, AND CONTROLS REQUIRED PLUMBI N STUB -OUT POINT AND LOWPOINS FOR INSTALLATION ON THE EQUIPMENT. 3.38 PLUMBING CONTRACTOR SHALL FURNISH AND INSTALL ALL SUPPLIES AND STOPS, TRAPS, VALVES, CONTROLS, AND OTHER ACCESSORIES THAT ARE NOT AN INTEGRAL PART OF THE KITCHEN EQUIPMENT AS REQUIRED TO MAKE CONNECTIONS TO THE EQUIPMENT FOR A COMPLETE AND OPERATING SYSTEM IN COMPLIANCE WITH ALL APPLICABLE CODES AND ORDINANCES. 3.39 ALL INDIRECT DRAIN LINES FROM FOOD SERVICE EQUIPMENT TO THE NEAREST INDIRECT DRAIN SHALL BE FURNISHED AND INSTALLED BY THE PLUMBING CONTRACTOR TO CONFORM WITH ALL APPLICABLE CODES AND ORDINANCES. VERIFY ROUTING OF DRAIN LINES WITH FOOD SERVICE EQUIPMENT CONTRACTOR. PLUMBING CONTRACTOR SHALL INSULATE DRAINS SERVICE FREEZER, ICE BINS, ETC. 3.40 NO KITCHEN FAUCETS WILL BE SUPPLIED UNDER PLUMBING SECTION OF WORK EXCEPT AS SCHEDULED ON THE PLUMBING DRAWINGS. 3.41 CAREFULLY REVIEW ALL PLUMBING AND FOOD SERVICE DRAWINGS WITH REFERENCE TO KITCHEN EQUIPMENT FOR INSTRUCTIONS REGARDING THE INSTALLATION OF PLUMBING SERVICES. REVIEW PLUMBING CONTRACTOR RESPON- SIBILITIES. MAKE ALL REQUIRED CONNECTIONS AND COORDINATE WITH KITCHEN EQUIPMENT SUPPLIER WHERE APPLICABLE. REVIEW THIS PORTION OF THE PLUMBING INSTALLATION WITH THE GENERAL CONTRACTOR AND OWNER'S REPRESENTATIVE PRIOR TO COMMENCEMENT OF WORK. 3.42 PLUMBING CONTRACTOR SHALL PROVIDE SHUT-OFF VALVES AT ALL WATER AND GAS CONNECTIONS TO KITCHEN EQUIPMENT. 3.43 PRIOR TO ROUGH -IN OF ANY FIXTURE OR EQUIPMENT, REVIEW ALL CURRENT ARCHITECTURAL, MECHANICAL, AND KITCHEN WHERE APPLICABLE EQUIPMENT DRAWINGS, EQUIPMENT/FIXTURE ROUGH -IN DRAWINGS AND DATA SHEETS AND CONFER WITH ARCHITECT, MECHANICAL CONTRACTOR, AND KITCHEN EQUIPMENT CONTRACTOR FOR INSTRUCTIONS AND CLARIFICATIONS. 2.44 ALL VENT LINES SHALL BE SLOPED AWAY FROM CONNECTIONS TO STACK AND TOWARD THE FIXTURE IN ORDER TO PREVENT THE ENTRAPMENT OF FLUIDS IN THE VENT LINE. 3.45 ALL DRAINAGE LINES SHALL BE SLOPED AT A MINIMUM OF 1/4 IN. PER LINEAL FOOT. 3.46 PIPE SUPPORTS SHALL BE ADJUSTABLE BAND HANGERS WITH ZINC ELECTROPLATING FOR STEEL PIPE AND COPPER ELECTROPLATING FOR COPPER TUBE. SUPPORT PIPING FROM HANGERS WITH SUPPORTING RODS. UPPER ATTACHMENTS SHALL BE AS RECOMMENDED BY MANUFACTURER FOR SECURING TO EXISTING STRUCTURE. SUPPORT VERTICAL PIPES WITH APPROVED BRACKETS OR CLAMPS. ROD DIAMETERS PER APPLICABLE CODE. SUPPORT GAS PIPING AT 8ft. INTERVALS WITH HANGERS AND SOLID RODS AT EACH HANGER. ALL PIPE HANGERS SHALL BE INSTALLED TO CONFORM TO LOCAL SEIEMIC REQUIREMENTS. INSULATED PIPING SHALL HAVE INSULATION' SHIELD. 3.47 THIS CONTRACTOR SHALL PROVIDE PLUMBING EQUIPMENT, FITTINGS,' AND TRIM WHERE SPECIFIED OR AS REQUIRED FOR COMPLETE INSTALLATION. THIS CONTRACTOR SHALL ROUGH -IN AND CONNECT ALL EQUIPMENT INCLUDING EQUIPMENT FURNISHED BY OTHERS. 3.48 SOIL, WASTE, AND VENT SYSTEMS SHALL BE TESTED AT 10 ft. STATIC HEAD 30 min. WITH NO DROP. POTABLE WATER PIPES, VALVES, AND FITTINGS SHALL BE DISINFECTED, AND HYDROSTATICALLY TESTED AT 100 p.s.i.g. FOR 30 min. WITH NO DROP IN PRESSURE. 3,49 ALL COLD AND HOT WATER SUPPLY LINES SHALL BE RUN CONCEALED ABOVE CEILING AND/OR CONCEALED IN WALLS UNLESS OTHERWISE NOTED. INSTALL ON BUILDING SIDE OF INSULATION AND PROVIDE HEAT TAPE WHERE NECESSARY TO KEEP LINES FROM' FREEZING. I 3.50 FUEL GAS PIPING SHALL CONNECT TO APPLIANCES OR EQUIPMENT WITH GAS COCK, UNION, AND 6 in. DIRT LEG. ALL GAS LINES SHALL BE SUPPORTED 8 ft. ON CENTER. MATERIALS AND INSTALLATION SHALL COMPLY WITH UNIFORM PLUMBING CODE CHAPTER 12. 3.51 PIPING SHOWN ON THE DRAWINGS IS DIAGRAMMATICAL AND SHALL BE COORDINATED WITH ACTUAL JOB CONDITIONS, WORK OF OTHER TRADES, HEALTH DEPARTMENT, BUILDING DEPARTMENT INSPECTION AUTHORITIES. NO ADDITIONAL COST WILL BE ALLOWED FOR RELOCATION DUE TO CONFLICTS WITH OTHER TRADES OR LOCAL CODE REQUIREMENTS. 3.52 PLUMBING CONTRACTOR SHALL VERIFY EXACT LOCATION AND DEPTH' OF ALL UNDERGROUND UTILITIES AND SHALL BE RESPONSIBLE FOR DAMAGE TO ANY PUBLIC OR PRIVATE UTILITIES, WHETHER SHOWN OR NOT HEREON. REVIEW THE ENTIRE INSTALLATION WITH JACKSONS FOOD STORE STORE REPRESENTATIVE PRIOR TO START OF WORK. t:,EVIEVVED FOR CODE COMPLIANCE APPROVED FEB 2 4 2011 City of TukwiTS BUILDING DIVISION RECEIVED CITY OF TUKWILA JAN 2 4 2017 PERMIT CENTER 1 ABOSSEIN GIN EERING L.L.0 MECHANICAL - ELECTRICAL CIVIL - LEED - STRUCTURAL FIRE PROTECTION 2100 112TH AVE. NE BELLEVUE, WA 98004 OFFICE: (425) 462-9441 FAX: (425) 462-9451 EMAIL: CService@abossein.com WEBSITE: www.aboss-in.com 17450 W. VALLEY HWY TUKWILA, WASHINGTON 98188 SPECIFICATIONS PERMIT SET DATE: 01/20/2016 JOB NO. 216152 NO. DATE REVISION 3 OF 3