Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Home
My WebLink
About
Permit PG17-0078 - BOBA LUST - PLUMBING, GREASE TRAP, RPPA
BOBA LUST 319 TUKWILA PKWY PGI 7-0078 Parcel No: Address: City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Inspection Request Line: 206-438-9350 Web site: http://www.TukwilaWA.Rov PLUMBING/GAS PIPING PERMIT 0223000010 319 TUKWILA PKWY Project Name: BOBA LUST Permit Number: PG17-0078 Issue Date: Permit Expires On: 7/31/2017- 1/27/2018- Owner: /31/20171/27/2018' Owner: Name: Address: Contact Person: Name: Address: Contractor: Name: Address: License No: Lender: Name: Address: BETA HOLDINGS LTD 18827 BOTHELL WAY NE , BOTHELL, WA, 98011 VICTOR PHAM 13057 56TH AVE S , TUKWILA, WA, 98178 OWNER AFFIDAVIT - VICTOR PHAM I// /!1 Phone: (206) 218-2891 Phone: Expiration Date: DESCRIPTION OF WORK: 1) IDENTIFY EXISTING DRAINAGE & PLUMBING PROFILE. 2) MODIFY & INSTALL NEW PLUMBING ACCORDING TO THE EQUIPMENT SCHEDULE. INCLUDES INSTALLATION OF A GREASE TRAP AND RPPA ON SINK/ICE MACHINE COLD WATER SUPPLY. Valuation of Work: $0.00 Water District: TUKWILA Sewer District: TUKWILA Fees Collected: $287.63 Current Codes adopted by the City of Tukwila: International Building Code Edition: International Residential Code Edition: International Mechanical Code Edition: Uniform Plumbing Code Edition: International Fuel Gas Code: 2015 2015 2015 2015 2015 National Electrical Code: WA Cities Electrical Code: WAC 296-46B: WA State Energy Code: Permit Center Authorized Signature: Date: 2014 2014 2014 2015 1 hearby certify that I have read and examined this permit and know the same to be true and correct. All provisions of law and ordinances governing this work will be complied with, whether specified herein or not. The granting of this permit does not presume to give authority to violate or cancel the provisions of any other state or local, laws regulating construction or the performance of work. I am authorized to sign and obtain this development permit and agree to the conditions attached to this permit. Signature: Print Name: U�'�✓ Dater/5 /// This permit shall become null and void if the work is not commenced within 180 days for the date of issuance, or if the work is suspended or abandoned for a period of 180 days from the last inspection. PERMIT CONDITIONS: 1: ***PLUMBING/GAS PIPING PERMIT CONDITIONS*** 2: No changes shall be made to applicable plans and specifications unless prior approval is obtained from the Tukwila Building Division. 3. All permits, inspection records and applicable plans shall be maintained at the job and available to the plumbing inspector. 4: All plumbing and gas piping systems shall be installed in compliance with the Uniform Plumbing Code and the Fuel Gas Code. 5: No portion of any plumbing system or gas piping shall be concealed until inspected and approved. 6: All plumbing and gas piping systems shall be tested and approved as required by the Plumbing Code and Fuel Gas Code. Tests shall be conducted in the presence of the Plumbing Inspector. It shall be the duty of the holder of the permit to make sure that the work will stand the test prescribed before giving notification that the work is ready for inspection. 7: No water, soil, or waste pipe shall be installed or permitted outside of a building or in an exterior wall unless, adequate provision is made to protect such pipe from freezing. All hot and cold water pipes installed outside the conditioned space shall be insulated to minimum R-3. 8: Plastic and copper piping running through framing members to within one (1) inch of the exposed framing shall be protected by steel nail plates not less than 18 gauge. 9: Piping through concrete or masonry walls shall not be subject to any load from building construction. No plumbing piping shall be directly embedded in concrete or masonry. 10: All pipes penetrating floor/ceiling assemblies and fire -resistance rated walls or partitions shall be protected in accordance with the requirements of the building code. 11: Piping in the ground shall be laid on a firm bed for its entire length. Trenches shall be backfilled in thin layers to twelve inches above the top of the piping with clean earth, which shall not contain stones, boulders, cinderfill, frozen earth, or construction debris. 12: The issuance of a permit or approval of plans and specifications shall not be construed to be a permit for, or an approval of, any violation of any of the provisions of the Plumbing Code or Fuel Gas Code or any other ordinance of the jurisdiction. 13: The applicant agrees that he or she will hire a licensed plumber to perform the work outlined in this permit. 14: All new plumbing fixtures installed in new construction and all remodeling involving replacement of plumbing fixtures in all residential, hotel, motel, school, industrial, commercial use or other occupancies that use significant quantities of water shall comply with Washington States Water Efficiency ad Conservation Standards in accordance with RCW 19.27.170 and the 2006 Uniform Plumbing Code Section 402 of Washington State Amendments 15: The grease interceptor shall be installed per manufacturer's specifications. 16: Applicant shall call 206 433-0179 minimum 24 hors in advance to schedule the RPPA backflow inspection The Reduced Pressure Backflow Preventer shall be installed per manufacturer's specification and shall be tested by a certified tester. Copy of the backflow test report shall be submitted to the Public Works Inspector. Thereafter the backflow shall be tested annually by a certified backflow tester and copy of the test report shall be forwarded to Tukwila Water Dept., 600 Minkler Blvd, Tukwila, WA 98188, phone 206 433-1860, fax 206 575-3404. PERMIT INSPECTIONS REQUIRED Permit Inspection Line: (206) 438-9350 8004 GROUNDWORK 1900 PLUMBING FINAL 8005 ROUGH -IN PLUMBING CITY OF TUK LA Community Development Department Permit Center 6300 Southcenter Blvd., Suite 100 Tukwila, WA 98188 http://www.TukwilaWA.gov Plumbing/Gas .Permit No. ?/-7-0°7( Project No. Date Application Accepted: 0&//q/i7 Date Application Expires: II -10/(7 (For gfce use only) PLUMBING / GAS PIPING PE MIT APPLICATION Applications and plans must be complete in order to be accepted for plan review. Applications will not be accepted through the mail or by fax. **Please Print** SITE LOCATION j/ Ttii3O 4 „ /24 Site Address: Tenant Name: PROPERTY OWNER Name: \ / y "/ Address: / 3051 i7 ---'i $ City. 4 State: Vorip:78/ /Phone:emcv1 Name lin Contr Reg No.60 17e '7 �/ Exp Date: learlie- `4W64 Addre 4 �� 7 ll ill /1./1^fes` � . City: State Zip: 14.1 o CONTACT PERSON — person receiving all project. communicati%n Name: \ / y "/ Address: / 3051 i7 ---'i $ City. 4 State: Vorip:78/ /Phone:emcv1 F Email: Valuation of Project (contractor's bid price): S, pe of Work (plea�, provide detailed information): King Co Assessor's Tax No.: Suite Number: Floor: l.( t New Tenant: Yes ❑.. No PLUMBING CONTRACTOR INFORMATION Company Name: rvr,,_ %./..fid J Addrx ey. C SW' A'S--- A..' _.,1P;7 City,_: Q jeo� I� State " Zi9�� ;�j� ZIJ Phok F ,®7/..- Contr Reg No.60 17e '7 �/ Exp Date: learlie- Tukwila Business Zcense No.: Building Use (per Int'l Building Code): Occupancy (per Int'] Building Code): Utility Purveyor: Water: H:\Applications\Forms-Applications On Line\2011 Applications\Plumbing Permit Application Revised 8-9-11.docx Revised: August 2011 bh Sewer: Page 1 of 2 Indicate type of plumbing fixtures anc, ,as piping outlets being installed and the qua;_ below: Fixture Type Qty Bathtub or combination bath/shower i Dishwasher, domestic with independent drain / Shower, single head trap Sinks, t Rain water system — per drain (inside building) Grease interceptor for commercial kitchen (>750 gallon capacity) / Each additional medical gas inlets/outlets greater than 5 Atmospheric -type vacuum breakers not included in lawn sprinkler backflow protections (1-5) Fixture Type Qty Bidet i Drinking fountain or water cooler (per head) / Lavatory Urinal Water heater and/or vent Repair or alteration of drainage or vent piping / Repair or alteration of water piping and/or water treatment equipment Backflow protective device other than atmospheric - type vacuum breakers 2 . inch (51 mm) diameter or smaller Atmospheric -type vacuum breakers not included in lawn sprinkler backflow protections over 5 IT APPLo ATION NOTES - Fixture Type Qty Clothes washer, domestic i Food -waste grinder, commercial / Wash fountain Water closet Industrial waste treatment interceptor, including trap and vent, except for kitchen type grease interceptors ' Repair or alteration of drainage or vent piping Backflow protective device other than atmospheric -type vacuum breakers over 2 inch (51 mm) diameter Gas piping outlets Fixture Type Qty Dental unit, cuspidor i Floor drain / Receptor, indirect waste Building sewer and each trailer park sewer Each grease trap (connected to not more than 4 fixtures - <750 gallon capacity Medical gas piping system serving 1-5 inlets/outlets for a specific gas Each lawn sprinkler system on any one meter including backflow protection devices Value of Consfr'uction'- In all cases, a value of construction amount should be entered by the applicant. This figure will be reviewed and is subject -to possible revision by the Permit Center to comply with current fee schedules. Expiration of Plan Review — Applications for which no permit is issued within 180 days following the date of application shall expire by limitation. The Building Official may grant one extension of time for an additional period not to exceed 180 days. The extension shall be requested in writing and justifiable cause demonstrated. Section 103.4.3 Intemational Plumbing Code (current edition). I HEREBY CERTIFY THAT I HAVE READ AND EXAMINED THIS APPLICATION AND KNOW THE SAME TO BE TRUE UNDER PENALTY OF PERJURY BY THE LAWS OF THE STATE OF WASHINGTON, AND I AM AUTHORIZED TO APPLY FOR THIS PERMIT. BUILDING OWNER 0 • I UTHORIZED AGENT: Signature: ,././ 6 Print Name: Date: Day Telephone: Mailing Address: ty H:\Applications\Forms-Applications On Line \2011 Applications\Plumbing Permit Application Revised 8-9-11.docx Revised: August2011 bh State Zip Page 2 of 2 DESCRIPTIONS PermitTRAK ACCOUNT QUANTITY PAID $509.36 EL17-0469 Address: 319 TUKWILA PKWY Apn: 0223000010 $221.73 Credit Card Fee $6.46 Credit Card Fee R000.369.908.00.00 0.00 $6.46 ELECTRICAL $205.02 PERMIT FEE MULTI-FAM/COMM R000.322.101.00.00 0.00 $205.02 TECHNOLOGY FEE $10.25 TECHNOLOGY FEE R000.322.900.04.00 0.00 $10.25 PG17-0078 Address: 319 TUKWILA PKWY Apn: 0223000010 $287.63 Credit Card Fee $8.38 Credit Card Fee R000.369.908.00.00 I 0.00 I $8.38 PLUMBING $268.51 PERMIT FEE R000.322.100.00.00 0.00 $181.66 PERMIT ISSUANCE BASE FEE R000.322.100.00.00 0.00 $33.15 PLAN CHECK FEE R000.322.103.00.00 0.00 $53.70 TECHNOLOGY FEE $10.74 TECHNOLOGY FEE TOTAL FEES PAID BY RECEIPT: R11751 R000.322.900.04.00 R 0.00 $10.74 $509.36 Date Paid: Monday, June 19, 2017 Paid By: VICTOR PHAM Pay Method: CREDIT CARD 052601 Printed: Monday, June 19, 2017 4:26 PM 1 of 1 A SYSTEMS Rachelle Ripley From: Lee Sipe Sent: Wednesday, February 21, 2018 7:53 AM To: Rachelle Ripley Subject: RE: PG 17-0078 I can't find this report either. I remember I finalized this one. Lee From: Rachelle Ripley Sent: Friday, February 16, 2018 3:03 PM To: Lee Sipe <Lee.Sipe@TukwilaWA.gov> Subject: PG17-0078 Hi Lee, Do you have a copy of an inspection report for PG17-0078, plumbing final on 10/24/17. Thanks, Rachelle Ripley Permit Technician City of Tukwila 6300 Southcenter Bl, Suite 100 I Tukwila, WA 98188 T: 206.433.7165 I F: 206.431.3665 Rachelle.Ripley@TukwilaWA.gov I http://www.TukwilaWA.gov INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 Pr 'e+4 Lct: tSC7f i T e of Inspection: (J 4 - h,1 �� r't'Ia9Ak2 Address: ')(1 7-1/40iiA AliAdV Date Called: Special Instructions: Date Wa e rzii Request : Phone No: 1 Approved per applicable codes. LJ Corrections required prior to approval. COMMENTS: OK 1.O vG /1 pz1cir i1Sl ' Inspector: Date: REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. cp INSPECTION RECORD Retain a copy with permit INSPECTION NO. PERMIT NO. CITY OF TUKWILA BUILDING DIVISION 6300 Southcenter Blvd., #100, Tukwila. WA 98188 (206) 431-3670 Permit Inspection Request Line (206) 438-9350 l7- 0076 Prrect: �/� :.,a74 Type of Inspection: Address: -3ig 1)'&4 0404 Date Called: Special Instructions: Date Waj t /% /% a.m. pm. :II Request Phone No: Approved per applicable codes. Li Corrections required prior to approval. COMMENTS:..,/.. co 7k rvP0A/Aix/N� 1- - Inspector: Date: REINSPECTION FEE REQUIRED. Prior to next inspection, fee must be paid at 6300 Southcenter Blvd., Suite 100. Call to schedule reinspection. tC 1.I\ ;e I j, \ 4jj\ • Y2,14\ 3411 V :.0 0 n • 0 /0 0 0 0 DomesT-Ic 14O V/CoLotPec+Rc._ WATE4. PIPING %5OMeTR'C. REVIEWED FOR CODE COW.PLIANCE APPROVED JUL 2 7 2.fl17 City of Tukwila BUILDING DIVISION 7- 007 CA 18 2017 SO GALLON WATER NEATER W/ GtRc. PvtdtP. REctg.c. PUMP W%CHEc.K VAL-VES ANO ISOLATt0N VALVES. HAND SINK b- COMPAP:CME.NT SINK sitAK SINK SINk IIGE MACEItNE. (COLD WATe. )PPI„' WRAP. e-01-4 . wt_►sT!_arrt- P(Q.CN`G_-14s�ltcs --- 2' 0 TO SQA N i TA RY SEWER P O C r I rvrmen For COM -i I Miii-2 .IANOU Y1�ll. 2 7 2U1? City of Tukwila 8UI i . INO DIVISION CITEKWILA 13 2017 PERMITJUL CENTER 0 2° FLOOR ORMN W/ PRIMER 0 2" FLOOR S►NK HANG SINK N.J/CLEAlialr @ WALL 0 .1" FLOOtk Sit`i1t . { INYE RC,.EPTC}P.) Q St N K W/ CI.E.ANOJT wPLL 0 3u Ft -000 .LE.aNOUT O SINK w /cLENNo.UT &. WI LL °I `=' .. " Ft-n0E. Da N wLaz N1E.k D G 1d5.PNG 0.000 Verizon LTE deVv�Y�Ui https://mail.goor- •om/ /scs/mail-static/ /js/k=gmail.main.en.HFK 1:54 PM apollovalves.com /*64IND BACKFLOW PREVENTION CATALOG I Reduced Pressure Backflow Preventers RP 4A Sizes 1/2", 314:1:1-1(4;1-112:2" FACTORY CODE REDUCED PRESSURE PRINCIPLE The Apollo" Series RP 4A Reduced Pressure Principle Backtlow Preventer is desig maximum protection against backflow caused by either back -pressure or backsipt substances that are hazardous. The durable but economical device is easily maint line with modular check cartridge assemblies that require no special tools. It consist independently acting spring-loaded check valves with an automatic differential located between the check valves. All testcocks are mounted at the top of the ui easy access during repair and maintenance when unit is installed in tight places. FEATURES • Maximum protection against • UL Classified (less shut -offs) back-pressure/back-siphonage • Approved by the Foundation Modular check valve cartridges w/easily Cross -Connection Control ant replaced parts Hydraulic Research at the • Reversible/removable chloramine- University of Southern Califon resistant silicone seat discs • Standard with full port ball • Low head pressure loss stainless steel handles • Top mounted test cocks - Corrosion resistant • Threaded testcock protectors • Maximum working pressure 1 • Internal sensing passage • Operating temperature range • ASSE 1013 • Horizontal installation approv • CSA 864.4 1/2" through 2" • Lead -Free option • Designed, cast, manufacturec • NSF 61/8/G/372 and tested in South Carolina, • Federal Public Law 111-380 • 5 year, domestic warranty AW WA CS11 MATERIALS Pm Material Body and Caps Bronze ((84400, LF C89836) BV Shut -offs, Tretcocks Bronze C84400 or (87800 Lead Free Springs 300 Series 5S Seat Discs Chloramine -resistant Silicone Diaphragm Nitrite and Nylon Check Modules Glass -Filled PPO 0 -rings t:hioramine-resistantEPDM Ball Valve Handles Stainless Steel Contact local water authorities for installation/servicerequirements. 4A IX) 2x Y -STRAINER x SIZE Ax SHUT-OPPVALYES x OPTIONS (CAN BE COMBINED) 4A = Non -Lead Free 0= Standard 3= 1/2' 2= w/balvalves (Standard) F =SAE threaded test cocks (standard 4AIF = lead Free 1= WithY-Strainer 4= 3/4" 4= w/union ball valves (3/4%2") L =lever handle (3/4"&1"only) (Shipped loose) 5= 1" 11. =Locking lever handles 6= 1-1/4" PR=Press Connection 7= 1-1/2" P =Push Connection 8= 2" Example: 4A 21S RILL = V' Reduced Pressure Bc Preventer with strainer, union ball vah locking lever handles RECEIVED CITY OFTUKWtLQ �0��%C�N JUL 24 2017 LTR# ba(AVA(D-\-___ P6-1 t3- (tptg REVIEWED FOR CODE COMPLIANCE APPROVED JUL 2'7 2011 City of Tukwila BUILDING DIVISION p RmixacERT 141 Customer Service 1704) 841-6000 Cb n� D/_ 1/1 flfllQ) I 4G_1036.PNG •0000 Verizon LTE 22 1:54 PM apollovalves.com https://mail.goog1' ':om/ /scs/mail-static/ /js/k=gmail.main.en.HFK 1 * 64%x' www.apollovalves.com Customer Service (704) 841-6000 1Ao F0E My BACKFLOW PREVENTION CATALOG Reduced Pressure Backflow Preventers B A • DIMENSIONS OP-4412— Model Mo, w RP4412 RP4*34 RP4434 RP441 RP441 RP44114- RP44114 RPM112 linter/No. 4420342F 4420342F 4420442F 4420442f 4420542F 44205421 4420642 44 206 42 4420742 Size 1/2' 1Smm. 3/4 20mm. 1' 2Smm. 1.1/4' 32 mm. 14/2' See Page 61 For Flow Cul RP44112 11442 RP4 4420742 4420842 4420 40mm. 2 50�n A• 10-7/8 276 12-5/8 321 14-5/8 8 7.3/8 187 8-1/2 216 9-1/2 C 7.1/8 181 7.3/8 187 8 0 2.7/8 73 3-1/8 79 3-1/4 3-1/4 83 3-1/2 89 4 3.7/8 98 3-7/8 98 4 i WEIGHTS lbs. kg lbs. kg tbs. Net Wt. 6.9 3.1 8.2 3.7 11.7 'For Union Ball Valve, Press, and Push connection dimensions, see submittal sheets. 1A cZo'Yalves it'''''""")Customer Service (704) 841-6000 371 241 203 83 100 100 kg 5.3 17.1/2 11-3/4 9-7/8 5-1/8 4-1/2 5-3/8 lbs. 13.6 For additional information, submittal sheets and manuals, visit uwsv.apollovalves.com 445 18 298 11-5/8 251 9-7/8 130 5-1/8 114 4-1/2 137 5-3/8 RI. lbs. 6.2 17.4 457 295 251 130 114 137 20-1/8 12-3/4 11 5-7/8 5 6 51' 32, 271 14! 12; 151 kg. tbs. 7.9 243 &ADA \Adt\--\-- ,GB1 20/25 GPM grease interceptor RECEIVED JUL 17 2017 TUKWILA PUBLIC WORKS Specification and Submittal SUBMITTAL Standard CORRECTION LTR# Location: indoor Installation: above/below grade Flow Rates / Grease Capacities: 20 GPM (1.3 L/s) / 70 lbs. (31.8 kg) 25 GPM (76 L/s) / 64.9 lbs. (29.4 kg) Liquid Capacity: 10 gal. (37.9 L) Approval Weight: 39 lbs. (17.7 kg) Connections: 3" (75 mm) FPT inlet/outlet with 3" x 2" (75 mm x 50 mm) FPT fittings Cover: bolted gas/water tight polypropylene with 450 Ib. load rating, or 1,000 lb. when unit is buried with FCR1 riser Signature: Date: Specifying Engineer: Options EIVED F TUKWILA JUL 13 2017 PERMIT CENTER FCR1 (x1): > 2-1/8" -12" field cut riser U FCR1 (x2): > 12" - 24" field cut risers CCI: membrane clamping collar kit (requires FCR1 riser) PP1: pumpout port kit Engineering Firm: Company: G 17- 007f$ SCHIER %.� LIFETIME GUARANTEED Coo. GREASE INTERCEPTORS MODEL NUMBER: GB1 PART 5:4060-001-01 DESCRIPTION: 20/25 GPM Polyethylene Grease Interceptor DWG BY: B. Karrer 9500 Woodend Road I Edwardsville, KS 66111 J Tel: 913-951-3300 1 www.schierproducts.com DATE: 4/18/2017 REV: ECO: © Copyright 2017 Schier, All Rights Reserved page 1 of 3 SPECIAL PRECAUTIONS For All Schier Great Basin- Grease Interceptor Installations Installation Instructions Installation instructions and additional components are located inside the interceptor. Read all instructions prior to installation. This interceptor is intended to be installed by a licensed plumber in conformance with all local codes. When Installing Interceptor Inside If your dishwashing sink(s) discharges into a floor drain/sink (drain), you must regulate the flow into the drain to avoid an overflow of water onto the kitchen floor. This can be done by installing a valve or flow restriction cap on the sink piping that discharges into the drain. See drawing below for guidance. For detailed guidance on indirect connections, go to: http://webtooms.schierproducts.com/Tech nicai_Data/Indirect_Connections.pdf Fernco or similar rubber flow restriction end cap Hydrostatic Slabs (or Pressure Slabs) When instated under a hydrostatic slab (slab designed to withstand upward lift, usually caused by hydrostatic pressure) interceptor must be enclosed in a watertight concrete vault. Failure to follow this guidance voids your warranty. concrete slab subject to hydrostatic pressure watertight concrete vault High Temperature Kitchen Water If water is entering the interceptor at excessive temperature (over 140° F), a drain water tempering valve (DTV) must be instated. Most state and local plumbing codes prohibit water above 140° F being discharged into the sanitary sewer. Water above 140° F will weaken or deform PVC Schedule 40 pipe, poly drainage fixtures Eke interceptors and erode the coating of cast iron (leading to eventual failure). Failure to follow this guidance voids your warranty. High Water Table Installations Interceptors and risers are not designed to withstand water table height in excess of the top of the unit when buried (see figure). If it is possible for this to occur, install the interceptor and risers in awater-tight concrete vault or backfill with concrete or flowable fill (wet concrete and flowable backfill should be poured in stages to avoid crushing the interceptor). At risk areas include but are not limited to tidal surge areas, floodplains and areas that receive storm water. Failure to follow this guidance voids your warranty. Models G8-50, GB -75, and GB -250 that are direct buried in high water table scenarios must be installed with model AK1 anchor kit or warranty is void. max water table height for direct burial al• I{� ti 11111 • r li!IF I;fI,,G i1�ipY+l'a?D?ifi� �?� 1i: 6Yi;;rhllli,' -1;YG 1111 SCHIER " LIFETIME GUARANTEED %I. - GREASE INTERCEPTORS MODEL NUMBER: GB1 PART u: 4060-001-01 DESCRIPTION: 20/25 GPM Polyethylene Grease Interceptor DWG BY: B. Karrer 9500Woodend Road ( Edwardsville, KS 66111 I Tel: 913-951-3300 I www.schierproducts.com DATE: 4/18/2017 REV: ECO: CO Copyright 2017 Schier, AU Rights Reserved page 2 of 3 SPECIFICATION Motes 1. 3" FPT inlet/outlet with 3"x2" FPT fittings. 2. Unit weight -39lbs. (wet weight 123 lbs.) 3. Capacities - Liquid:10 gal. @20 GPM- Grease: 70 lbs. (9.6 gal.) ©25 GPM -Grease: 64.9 lbs. (8.9 gal.) 4. Built-in flow control. 5. For gravity drainage applications only. 6. Do not use for pressure applications. 7. Cover placement allows full access to tank for proper maintenance. 8. Vent not required unless per local code. 9. Engineered inlet and outlet diffusers are removable to inspect/clean piping. 10.Integral air relief / anti -siphon. Engineer Specification Guide Schier Great BasinTM grease interceptor model # GB1 shall be lifetime guaranteed and made in USA of seamless, rotationally -molded polyethylene. Interceptor shall be furnished for above or below grade installation. Interceptor shall be certified to ASME A112.14.3 (type C) and CSA 8481.1, with field cut riser system, built-in flow control, built-in test caps and three outlet options. Interceptor flow rate shall be 20 or 25 GPM. Interceptor grease capacity shall be 70 lbs. © 20 GPM or 64.9 lbs. @ 25 GPM. Cover shall provide water/gas-tight seal and have minimum 450 lbs. load capacity. Certified Performance Great Basin'"' hydromechanical grease interceptors are third party performance -tested and listed by IAPMO to ASME #A112.14.3 and CSA 13481.1 grease interceptor standards and greatly exceed requirements for grease separation and storage. They are compliant to the Uniform Plumbing Code. the National Standard Plumbing Code, the National Plumbing Code of Canada, and the International Plumbing Code. 2T Outlet 'A° (Optional) 23° Outlet "C" (Optional) 9-3/8' Shown with optional pumpout port kit A Outlet '8' (Standard) Outlet foot must face this direction in all configurations TOP VIEW Q. of 3' FPT inlet and outlet 12" 5' 11 7" }-- 0 21-1/2" Cover See Note #10 Engineered inlet and outlet diffuser 5-3/4' invert* Static water line *61/4' invert when using 3"x2° fittings SECTION A -A rlSCHIER LIFETIME GUARANTEED C.4,GREASE INTERCEPTORS MODEL NUMBER: GB1 PART tt: 4060-001-01 DESCRIPTION: 20/25 GPM Polyethylene Grease Interceptor DWG BY: B. Karrer 9500 Waodend Road 1 Edwardsville, KS 66111 1 Tel: 913-951-3300 i wwwschierproducts.com DATE: 4/18/2017 REV: ECO: © Copyright 2017Schier, All Rights Reserved page 3 of 3 July 21, 2017 City of Tukwila Department of Community Development VICTOR PHAM 13057 56TH AVE S TUKWILA, WA 98178 RE: Correction Letter # 2 PLUMBING/GAS PIPING Permit Application Number PG17-0078 BOBA LUST - 319 TUKWILA PKWY Dear VICTOR PHAM, Allan Ekberg, Mayor Jack Pace, Director This letter is to inform you of corrections that must be addressed before your development permit can be approved. All correction requests from each department must be addressed at the same time and reflected on your drawings. I have enclosed comments from the following departments: PW - C DEPARTMENT: Joanna Spencer at 206-431-2440 if you have questions regarding these comments. • 1) Note #7 on the Domestic Hot/Cold Water Piping Isometric plan calls for an RPPA backflow. Please specify backflow size/ manufacturer/model number and submit a cut sheet. Circle the RPPA to be installed. Please note that the RPPA shall be a WA State Dept. of Health approved backflow. Please address the comments above in an itemized format with applicable revised plans, specifications, and/or other documentation. The City requires that two (2) sets of revised plan pages, specifications and/or other documentation be resubmitted with the appropriate revision block. In order to better expedite your resubmittal, a 'Revision Submittal Sheet' must accompany every resubmittal. I have enclosed one for your convenience. Corrections/revisions must be made in person and will not be accepted through the mail or by a messenger service. If you have any questions, I can be reached at (206)433-7165. Sincerely, Rachelle Ripley Permit Technician File No. PG17-0078 6?01) cn„}tiromtor Rn,i%a,,nrd Quan.#11111 Tnl.,.,an IAL mob:« s . nQIQQ - Dl ..... . "MK 477 ?4'71 — ')/14" A I 7 -3ttc June 23, 2017 City of Tukwila Department of Community Development VICTOR PHAM 13057 56TH AVE S TUKWILA, WA 98178 RE: Correction Letter # 1 PLUMBING/GAS PIPING Permit Application Number PG17-0078 BOBA LUST - 319 TUKWILA PKWY Dear VICTOR PHAM, Allan Ekberg, Mayor Jack Pace, Director This letter is to inform you of corrections that must be addressed before your development permit can be approved. All correction requests from each department must be addressed at the same time and reflected on your drawings. I have enclosed comments from the following departments: BUILDING - PG DEPARTMENT: Allen Johannessen at 206-433-7163 if you have questions regarding these comments. • (GENERAL NOTE) PLAN SUBMITTALS: (Min. size 11x17 to maximum size of 24x36; all sheets shall be the same size. New revised plan sheets shall be the same size sheets as those previously submitted.) (If applicable) "STAMP AND SIGNATURES" "Every page of a plan set must contain the seal/stamp, signature of the licensee(s) who prepared or who had direct supervision over the preparation of the work, and date of signature. Specifications that are prepared by or under the direct supervision of a licensee shall contain the seal/stamp, signature of the licensee and the date of signature. If the "specifications" prepared by a licensee are a portion of a bound specification document that contains specifications other than that of an engineering or land surveying nature, the licensee need only seal/stamp that portion or portions of the documents for which the licensee is responsible." It shall not be required to have each page of "specifications" (calculations) to be stamped and signed; Front page only will be sufficient. (WAC 196-23-010 & 196-23-020) (BUILDING REVIEW NOTES) The fixtures specified for this permit indicates install of floor drain, water heater, sinks, and a grease interceptor. 1. Provide a specific plumbing -plan diagram of all new plumbing supply and DWV. Include an isometric plumbing diagram specifying all elements and fixtures served by the supply and DWV. Specify point of connection, and specifically show drain vented to the roof. Plumbing that is existing, not to be altered, please indicate. 2. Provide manufactures specifications for the grease interceptor and show it sized to handle the fixtures served. Show how it is vented. 3. Show the floor drain trap is provided with a trap primer. Note: In response to these corrections for this permit -plan -review, other corrections may be needed. PW - PG DEPARTMENT: Joanna Spencer at 206-431-2440 if you have questions regarding these comments. • 1. Please submit specifications for the proposed grease interceptor including installation and maintenance requirements. Please address the comments above in an itemized format with applicable revised plans, specifications, and/or other documentation. The City requires that two (2) sets of revised plan pages, specifications and/or other documentation be resubmitted with the appropriate revision block. 6300 Southcenter Boulevard Suite #100 • Tukwila Washington 98188 • Phone 206-431-3670 • Fax 206-431-3665 In order to better expedite your resubmittal, a 'Revision Submittal Sheet' must accompany every resubmittal. I have enclosed one for your convenience. Corrections/revisions must be made in person and will not be accepted through the mail or by a messenger service. If you have any questions, I can be reached at (206)433-7165. Sincerel', , Rachelle Ripley Permit Technician File No. PG17-0078 6300 Southcenter Boulevard Suite #100 • Tukwila Washington 98188 • Phone 206-431-3670 • Fax 206-431-3665 PERMIT COORD COPY PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG17-0078 PROJECT NAME: BOBA LUST SITE ADDRESS: 319 TUKWILA PKWY DATE: 07/26/17 Original Plan Submittal Revision # before Permit Issued X Response to Correction Letter # 2 Revision # after Permit Issued DEPARTMENTS: Building Division n 339 QNv& i('i 11 Public Works il;l Fire Prevention Structural Planning Division ❑ Permit Coordinator PRELIMINARY REVIEW: Not Applicable (no approval/review required) DATE: 07/27/17 Structural Review Required REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: Approved Corrections Required DUE DATE: 08/24/17 ❑ Approved with Conditions ❑ Denied (corrections entered in Reviews) (ie: Zoning Issues) Notation: n REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg ❑ Fire ❑ Ping ❑ PW ❑ Staff Initials: 12/18/2013 PERMIT COORD COPY PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG17-0078 PROJECT NAME: BORA LUST SITE ADDRESS: 319 TUKWILA PKWY Original Plan Submittal X Response to Correction Letter # . 1 DATE: 07/13/17 Revision # before Permit Issued Revision # after Permit Issued AtAJG Building Division [. j Public Works Fire Prevention Structural Planning Division ❑ Permit Coordinator PRELIMINARY REVIEW: Not Applicable (no approval/review required) DATE: 07/18/17 Structural Review Required REVIEWER'S INITIALS: DATE: APPROVALS OR CORRECTIONS: Approved Corrections Required DUE DATE: 08/15/17 ❑ Approved with Conditions ❑ ❑ Denied ❑ (corrections entered in Reviews) (ie: Zoning Issues) Notation: & y\o e c i „ REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg Fire ❑ Ping ❑ PW 27 Staff Initials: 12/18/2013 PERMIT COORD COPY PLAN REVIEW/ROUTING SLIP PERMIT NUMBER: PG17-0078 PROJECT NAME: BOBA LUST SITE ADDRESS: 319 TUKWILA PKWY DATE: 06/19/17 X Original Plan Submittal Revision # before Permit Issued Response to Correction Letter # Deferred Submittal # after Permit Issued DEPARTMENTS: cg '2J j1 Building Division VAL cels h Public Works Fire Prevention Structural Planning Division ❑ ❑ Permit Coordinator n PRELIMINARY REVIEW: Not Applicable ri (no approval/review required) REVIEWER'S INITIALS: DATE: 06/20/17 Structural Review Required DATE: APPROVALS OR CORRECTIONS: Approved DUE DATE: 07/18/17 Approved with Conditions n Corrections Required Denied (corrections entered in Reviews) Notation: (ie: Zoning Issues) REVIEWER'S INITIALS: DATE: Permit Center Use Only CORRECTION LETTER MAILED: Departments issued corrections: Bldg Fire 0 Ping ❑ PW L'J Staff Initials: I� Y 12/18/2013 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Web site: http://www.TukwilaWA.gov REVISION SUBMITTAL Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Date: / )3 /i)JTh Plan Check/Permit Number: (7, r4- Doi ❑ Response to Incomplete Letter # Response to Correction Letter # ❑ Revision # after Permit is Issued ❑ Revision requested by a City Building Inspector or Plans Examiner ❑ Deferred Submittal # Project Name: Bobo( LA/01 'l -171b\) ,t. Project Address: 3 V1 ,.)y1i4', q13.1 to 5 Contact Person: V L(AW a1Y1/1; Phone Number: Summary of Revision: RECEIVED CITY OF TUKWILA JUL 13 2017 PERMIT CENTER Sheet Number(s): "Cloud" or highlight all areas of revision including date of revision Received at the City of Tukwila Permit Center by: Entered in TRAKiT on 7 ( ( 7 W:\Permit Center \Templates\Forms\Revision Submittal Form.doc Revised: August 2015 City of Tukwila REVISION SUBMITTAL Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, Washington 98188 Phone: 206-431-3670 Web site: http://www.TukwilaWA.gov Revision submittals must be submitted in person at the Permit Center. Revisions will not be accepted through the mail, fax, etc. Plan ChecklPermit Number: -P61 I1- 0016 Response to Incomplete Letter # Response to Correction Letter # Revision # after Permit is Issued Revision requested by a City Building Inspector or Plans Examiner Deferred Submittal # Project Name: bA Project Address: moi liatAA. WW1 Contact Person: V1C1Y 1 r ' Phone Number: Summary of Revision: RECEIVED CITY OF TUKWILI JU1. 2 4 2017 Sheet Number(s): _ PERMIT CENTER "Cloud" or highlight all areas of revision including date of revision Received at the City of Tukwila Permit Center by: N (lab .� a, ,Ni Lu1U `I .1 Entered in TRAKiT on W:\Permit Center \Templates\Forms\Revision Submittal Formdoc Revised: August 2015, CITY OF TUKWILA Department of Community Development 6300 Southcenter Boulevard, Tukwila, WA 98188 Telephone: (206) 431-367o FAX (206) 431-3665 E-mail: tukplanPci.tukwila.wa.us Permit Center/Building Division 206 431-3670 Public Works Department 206 433-0179 Planning Division 206 431-3670 AFFIDAVIT IN LIEU OF CONTRACTOR REGISTRATION STATE OF WASHINGTON) ) ss. COUNTY OF KING hAii is K [please print name] , states as follows: PERMIT NO: 1. I have made application for a permit from the City of Tukwila, Washington. 2. I understand that state law requires that all building construction contractors be registered with the State of Washington. The exceptions to this requirement are stated under Section 18.27.090 of the Revised Code of Washington, a copy of which is printed on the reverse side of this Affidavit. I have read or am familiar with RCW 18.27.090. 3. I understand that prior to issuance of a permit for work which is to be done by any contractor, the . City of Tukwila must verify either that the contractor is registered by the State of Washington, or that one of the exemptions stated under RCW 18.27.090 applies. 4. In order to provide verification to the City of Tukwila of my compliance with this requirement, I hereby attest that after reading the exemptions from the registration requirement of RCW 18.27.090, I consider the work authorized under this permit to be exempt under number , and will therefore not be performed by a registered contractor. 5. I understand that the licensing provision of RCW 19.28.161 through 19.28.271 shall not apply to persons making electrical installations on their own property or to regularly employed employees working on the premises of their employer. The proposed electrical work is not for the construction of a new building for rent, sale or lease. I understand that I may be waiving certain rights that I might otherwise have under state law in any decision to engage an unregistered contractor to perform construction work. Owner/O `per's Agent* Signed and sworn to before me this day of J u.t NOTAR PUBLIC ii and for ,209'1. Residing at Name as commissioned: My commission expires: 18.27.090 Exemptions. The registration provisions of this chapter do not apply to: 1. An authorized representative of the United States government, the state of Washington, or any incorporated city, town, county, township, irrigation district, reclamation district, or other municipal or political corporation or subdivision of this state; 2. Officers of a court when they are acting within the scope of their office; 3. Public utilities operating under the regulations of the utilities and transportation commission in construction, maintenance, or development work incidental to their own business; 4. Any construction, repair, or operation incidental to the discovering or producing of petroleum or gas, or the drilling, testing, abandoning, or other operation of any petroleum or gas well or any surface or underground mine or mineral deposit when performed by an owner or lessee; 5. The sale of any finished products, materials, or articles of merchandise that are not fabricated into and do not become a part of a structure under the common law of fixtures; 6. Any construction, alteration, improvement, or repair of personal property performed by the registered or legal owner, or by a mobile/manufactured home retail dealer or manufacturer licensed under chapter 46.70 RCW who shall warranty service and repairs under chapter 46.70 RCW; 7. Any construction, alteration, improvement, or repair carried on within the limits and boundaries of any site or reservation under the legal jurisdiction of the federal government; 8. Any person who only furnished materials, supplies, or equipment without fabricating them into, or consuming them in the performance of, the work of the contractor; 9. Any work or operation on one undertaking or project by one or more contracts, the aggregate contract price of which for labor and materials and all other items is less than five hundred dollars, such work or operations being considered as of a casual, minor, or inconsequential nature. The exemption prescribed in this subsection does not apply in any instance wherein the work or construction is only a part of a larger or major operation, whether undertaken by the same or a different contractor, or in which a division of the operation is made into contracts of amounts less than five hundred dollars for the purpose of evasion of this chapter or otherwise. The exemption prescribed in this subsection does not apply to a person who advertises or puts out any sign or card or other device which might indicate to the public that he or she is a contractor, or that he or she is qualified to engage in the business of contractor; 10. Any construction or operation incidental to the construction and repair of irrigation and drainage ditches of regularly constituted irrigation districts or reclamation districts; or to farming, dairying, agriculture, viticulture, horticulture, or stock or poultry raising; or to clearing or other work upon land in rural districts for fire prevention purposes; except when any of the above work is performed by a registered contractor; 11. An owner* who contracts for a project with a registered contractor, except that this exemption shall not deprive the owner of the protections of this chapter against registered and unregistered contractors. The exemption prescribed in this subsection does not apply to a person who performs the activities of a contractor for the purpose of leasing or selling improved property he or she has owned for less than twelve months; 12.* Any person working on his or her own property, whether occupied by him or her or not, and any person working on his or her personal residence, whether owned by him or her or not but this exemption shall not apply to any person who performs the activities of a contractor on his or her own property for the purpose of selling, demolishing, or leasing the property; 13. An owner* who performs maintenance, repair, and alteration work in or upon his or her own properties, or who uses his or her own employees to do such work; 14. A licensed architect or civil or professional engineer acting solely in his or her professional capacity, an electrician certified under the laws of the state of Washington, or a plumber certified under the laws of the state of Washington or licensed by a political subdivision of the state of Washington while operating within the boundaries of such political subdivision. The exemption provided in this subsection is applicable only when the person certified is operating within the scope of his or her certification; 15. Any person who engages in the activities herein regulated as an employee of a registered contractor with wages as his or her sole compensation or as an employee with wages as his or her sole compensation; 16. Contractors on highway projects who have been prequalified as required by RCW 47.28.070, with the department of transportation to perform highway construction, reconstruction, or maintenance work; 17. A mobile/manufactured home dealer or manufacturer who subcontracts the installation, set-up, or repair work to actively registered contractors. This exemption only applies to the installation, set-up, or repair of the mobile/manufactured homes that were manufactured or sold by the mobile/manufactured home dealer or manufacturer; 18. An entity who holds a valid electrical contractor's license under chapter 19.28. RCW that employs,a certified journeyman electrician; a.certified residential specialty electrician, or an electrical traineemeeting the,, requirements of chapter 19.28 RCW to perform plumbing work that is incidentally,.directly, and immediately appropriate to the like'.in-kindreplacement of a household appliance or other small household utilization equipment that requires limited electric -power and limited waste and/or water connections. -An electrical trainee must be supervised by a certified electrician while performing plumbing work. * Per Washington State Department of Labor and Industries lessee has been interpreted to be equivalent to owner for purposes of exemptions. EQUIPMENT Sc1 U L E ITEMS PROVIDED BY OWNER/TENNANT AND INSTALLED BY GENERAL CONTRACTOR. 1` OP SINK 17ETAIL. QTY No. DESCRIPTION MANUFACTURER & MODELS MOP SINK rETAIL. 1 1 BLENDER 1 BLENDTEC STEALTH 875 wattage -1800.0 watts 120v/50/60/1 -ph 1 2 Ice -O -Matic /Day Nugget Ice Maker w/ 510 -Ib Bin GEM0650AB55PS 770 -Ib 110v VERIFY H2O REQUIREMENTS AND DRAIN 1 3 SANDWICH PREP TABLES KOOL-IT KSTM-60-2-60 115/60/1-ph19.5 amps 1 4 2x Secura 8100MC 1800W Portable Induction Cooktop Countertop Burner, Gold 115v/60/1-ph6 amps A 1 5 Avantco 48" Narrow -Glass Door Back Bar Cooler Stainless Steel Top and LED Lighting UBB-24-486 120 Volts 15 amps 1 6 Paragon spin magic 5,cotton candy machine 115V 8 Amps 1 7 1 DOOR REACH—;IN REFRIGERATOR Adcraft USRF-1D/19 U -Star 19 Cu Ft 1200 watt 120V 10 Amps 1 8 1 DOOR REACH IN FREEZER Adcraft U -star USFZ 1d 1 door reach in freezer 115v/60/1 -ph 9.4 amps 1 9 HANDSINK 9x9 ' John Boos PBHS-W-0909 Hand Sink, Wall Mount, 115v/60/1 -ph 8.3 amps 1 10 3—COMP POT SINK 68.5"x25.5"w/DRAIN BOARD AND SHELVES John Boos E3S8-1620-12R18 Sink 1 11 18x27 SS SHELVING UNIT J013 NO: }CXXX 1 12 2 Gal Hot Water Dispenser 200 Degrees Fahrenheit punn 02500.0001 120v/60/1 -ph 1800w 15 amps 2 13 Autocut Manual Hand Towel Roll Dispensers - Smoke #JSD-53006-5-1 5 14 30x30 SS TABLE 4 15 3.5 gallon Narrow Iced Tea Dispenser Bunn 39600.0001 TDO -N-3.5 3.5 Gallon 1 16 Ice Bin, 24in.x2lin., Sin. Backsplash, 12in. deep, Insulated Chest Krowne 21-242100 Series, 1 17 GREASE INTERCEPTOR 1 18 \JOT USED 1 19 LIQUID SOAP DISPENSER 1 20 MOP SINK WITH SHELVES ABOVE . 1 21 50 GALLON HOT WATER TANK 1 22 EMPLOYEES LOCKER 1 23 Tabletop Napkin Dispensers - Black Pearl SAN JAMAR, 1 24 1 COMP SINK -24" wide x 24" front -to -back x 14" deep compartment John Boos E1S8-24-14-X Sink 25 FRP 2 FRP fil ti HALL SHEI`F FRP HALL 47\_. MOUNTED HOT HATER TANK FRP 55 TBL. 3-GOMPARTNT POT/DISH SINK a) I CP v CREASE FRP INTERCEPTOR MOP SINK 1() SEISMIC STRAPPING 0 fi 5/8" GYP.BD, 2x4 HOOP STUD, 5/8" EXTERIOR GRADE PLYWD. I/2" 'HONDERBOARD', FRP FINISH, SEE PLAN AND NOTE FOR HT. AND LOCATION. HONDERBOARD/FRP FINISH TO BE SILICONE SEALED TO IN LIP r MOP BASIN TO BE BONDED/SILIGC SEALED TO PLYWOOD PER MFR. RECOMMENDATIONS. WEST WALL SCALE: 1/2" - 1'0" Om TOP OF PLYWOOD mil BACKING EL: IO2° ock TOP OF PLATFORM EL:g6" BOTT. OF PLYWOOD mILJ BACKING EL: 86° PLATFORM SHELVING; 24" DEEP WIRE SHELVING W/ MATCHING: WALL MOUNT BRACKETS, SEE EQUIPMENT PLAN AND SCHEDULE FOR COUNT, SIZE, AND LOCATION. PACKAGE IS PART OF OWNERS EQUIPMENT PACKAGE INSTALLED BY THE GENERAL CONTRACTOR. MON G.G. TO ANCHOR WALL BRKTS. W/ #10 PHILLIPS HEAD SCREW (2'9 5/81' PLYWOOD BACKING IN LIEU 5/8" GYP. BOARD INSTALLED BY THE G.G. STUD WALL FRAMING FRP WALL FINISH MATERIAL---- MOP ATERIALi ALL FOOD BUST BE STOKED 6° FROM FLOOR FILE COPY Permit No. VT6P-- Plan review P3provaI is subject to errors and omissions. Approval of construction documents does not authorize the violation of any adopted code or ordinance. Receipt of approved Field Co• and condi ions i acknowledged: By: Date: 7 City of Tukwila BUILDING DIVISION II ExIeTNc -,4NEL II I/ HOT W4`ER TANK ON PLATFC f -O R 11-0P SI XiST1IN .RESTROOM OFFICE/ STORAGE RM SHELVING UNIT Ui1.111 II II lilt 11 0 0 11111111111111111111111 FRP FRP FRP FRP 1 PAPER TOWEL DISPENE SOAP DISPENSER ER IGE MAKER HAND SINK FRIG FREEZER FRP FRP EAST WALL SC,ALE:1/2" - 1'0" LTH JEP1FO NOTES 1. An indirect waste drain is required for the food preparation sink. three -compartment sink, mechanical dishwasher, Ice machine, pop dispenser, running water dipper well, steam table, walk-in refrigeration, and any equipment in which food is placed. 2.If the establishment continues to be in operation during the remodel, dust barriers must be installed to ensure that food protection and safety are not compromised. the food service establishment will be required to discontinue operations If any disruption in water, electrical, or sewer service occurs, due to the remodel. Wandwash facilities must be leapt accessible and functional during all hours of food service establishment operation. 3.A horizontal separation of at least 16 inches or a vertical partition of 16 inches in height is required between the food preparation sink and all other sinks and/or sources of contamination. 4.14ot water must be available to all handwash sinks within IS seconds. the hot water for the facility must not be used at any plumbing fixture for a minimum of 6 hours prior to the preoperational inspection. This is required so that proper testing of the 15 -second time requirement for hot water availability can be completed. S.AII food service equipment, both new and used, must be listed by the National Sanitation Foundation (NSF) or equivalent for its intended use. Used and new refrigeration must be capable of holding potentially hazardous food at 411 or below. 6.Used equipment ie subject to onsite inspection to determine acceptability for use in the proposed food service establishment. Used equipment must be clean, in proper operating condition, and in good repair. Used refrigeration must be capable of holding potentially hazardous foods at a temperature of 41°F or below 1. Extra wall protection is required on walla behind all sinks, Including restroom handwash sinks, and food preparation counters and tables. A 16 -Inch high backeplash of plastic laminate, fiberglass -reinforced plastic or equal le acceptable. A backsplash higher than 16 inches is required on the wall behind counter top equipment tallier than 16 inches. Floor to ceiling protection 18 required on the wall behind dishwashers. Wall protection behind mop sinks must cover the entire splash zone. Plastic coated hardboard is not acceptable. B.AII floors in the kitchen, food preparation, food service, Food storage, and dleivaahing areas must be surfaced with a durable, nonabsorbent, easily cleanable material. Expansion joints, seams, saw cute and the like in concrete floors in all areas, including customer seating areae, must be filled and sealed 60 as to provide a smooth and cleanable surface. 9.The ceiling above the food preparation areas must be nonperforated, nonabsorbent, smooth and easily cleanable. 10. All light fixtures in food preparation and storage areas must be provided with coves or shatterproof bulbs. 1I.Plumbing must meet state and local codes. 12.The ventilation system shall be installed and operated to meet applicable building, mechanical and fire codes. OFFICE/ STORAGE 1 3 4-12 SACK OF KITCHEN x 0 (E1 FD 193ELOW KITCHEN/ SERVICE 0 ID IN iNG AREA NAPKENSTRAW,TRASH COUNTER 13) REVISIONS No changes shall he made to the scope of work without prior approval of Tukwila Building Division. NOTE: Revisions will require a new plan submittal and may include additional plan review fees APA COMPLIANT COUNTER CErA;iA i E I`'; I MIT Q1JitE.0FOR: i 'Mccrianicat 51 E!ectrlcat Kmbing s Piping City of Tukwila BUILDING DIViSION NO CHANGES WILL 15E MADE UJITNOUT I-IEALTN DEPARTMENT APPROVAL PUBLIC I-IEALTH k7 KiNG COUNTY WEALTH !DEPARTMENT INSPECTION REQUIRED UFON COMPLETION OF WORK PRiOR TO OPENING r- 6 1` OP SINK 17ETAIL. z 0 0 ti 0 0 A MOP SINK rETAIL. II_ = I II -I/2 I -O II_ = I II I-1/2 I -O ALL FOOD BUST BE STOKED 6° FROM FLOOR FILE COPY Permit No. VT6P-- Plan review P3provaI is subject to errors and omissions. Approval of construction documents does not authorize the violation of any adopted code or ordinance. Receipt of approved Field Co• and condi ions i acknowledged: By: Date: 7 City of Tukwila BUILDING DIVISION II ExIeTNc -,4NEL II I/ HOT W4`ER TANK ON PLATFC f -O R 11-0P SI XiST1IN .RESTROOM OFFICE/ STORAGE RM SHELVING UNIT Ui1.111 II II lilt 11 0 0 11111111111111111111111 FRP FRP FRP FRP 1 PAPER TOWEL DISPENE SOAP DISPENSER ER IGE MAKER HAND SINK FRIG FREEZER FRP FRP EAST WALL SC,ALE:1/2" - 1'0" LTH JEP1FO NOTES 1. An indirect waste drain is required for the food preparation sink. three -compartment sink, mechanical dishwasher, Ice machine, pop dispenser, running water dipper well, steam table, walk-in refrigeration, and any equipment in which food is placed. 2.If the establishment continues to be in operation during the remodel, dust barriers must be installed to ensure that food protection and safety are not compromised. the food service establishment will be required to discontinue operations If any disruption in water, electrical, or sewer service occurs, due to the remodel. Wandwash facilities must be leapt accessible and functional during all hours of food service establishment operation. 3.A horizontal separation of at least 16 inches or a vertical partition of 16 inches in height is required between the food preparation sink and all other sinks and/or sources of contamination. 4.14ot water must be available to all handwash sinks within IS seconds. the hot water for the facility must not be used at any plumbing fixture for a minimum of 6 hours prior to the preoperational inspection. This is required so that proper testing of the 15 -second time requirement for hot water availability can be completed. S.AII food service equipment, both new and used, must be listed by the National Sanitation Foundation (NSF) or equivalent for its intended use. Used and new refrigeration must be capable of holding potentially hazardous food at 411 or below. 6.Used equipment ie subject to onsite inspection to determine acceptability for use in the proposed food service establishment. Used equipment must be clean, in proper operating condition, and in good repair. Used refrigeration must be capable of holding potentially hazardous foods at a temperature of 41°F or below 1. Extra wall protection is required on walla behind all sinks, Including restroom handwash sinks, and food preparation counters and tables. A 16 -Inch high backeplash of plastic laminate, fiberglass -reinforced plastic or equal le acceptable. A backsplash higher than 16 inches is required on the wall behind counter top equipment tallier than 16 inches. Floor to ceiling protection 18 required on the wall behind dishwashers. Wall protection behind mop sinks must cover the entire splash zone. Plastic coated hardboard is not acceptable. B.AII floors in the kitchen, food preparation, food service, Food storage, and dleivaahing areas must be surfaced with a durable, nonabsorbent, easily cleanable material. Expansion joints, seams, saw cute and the like in concrete floors in all areas, including customer seating areae, must be filled and sealed 60 as to provide a smooth and cleanable surface. 9.The ceiling above the food preparation areas must be nonperforated, nonabsorbent, smooth and easily cleanable. 10. All light fixtures in food preparation and storage areas must be provided with coves or shatterproof bulbs. 1I.Plumbing must meet state and local codes. 12.The ventilation system shall be installed and operated to meet applicable building, mechanical and fire codes. OFFICE/ STORAGE 1 3 4-12 SACK OF KITCHEN x 0 (E1 FD 193ELOW KITCHEN/ SERVICE 0 ID IN iNG AREA NAPKENSTRAW,TRASH COUNTER 13) REVISIONS No changes shall he made to the scope of work without prior approval of Tukwila Building Division. NOTE: Revisions will require a new plan submittal and may include additional plan review fees APA COMPLIANT COUNTER CErA;iA i E I`'; I MIT Q1JitE.0FOR: i 'Mccrianicat 51 E!ectrlcat Kmbing s Piping City of Tukwila BUILDING DIViSION NO CHANGES WILL 15E MADE UJITNOUT I-IEALTN DEPARTMENT APPROVAL PUBLIC I-IEALTH k7 KiNG COUNTY WEALTH !DEPARTMENT INSPECTION REQUIRED UFON COMPLETION OF WORK PRiOR TO OPENING r- 6 a t3 E F_ 1; fD 0Ii7 0 cQ ce,nom J O z 0 0 ti 0 0 A 1._ A V X DRAWN: M CHECK: CFI' J013 NO: }CXXX I. 1 T E R PIRSCHER C DA ARCHITECTS GDA + PIrscher Architects 23114 100 AVE NI EDMONDS, WASHINGTON, 418020 (206)368-1668 Q SCALE: 1/411_1I_0ll RECEIVED CITY OF TUKWILA JUN 19 2017