The URL can be used to link to this page

Home My WebLink AboutPermit PL15-0051 - COLIN ROBINSON FOR T-MOBILE - SOUTHCENTER PLACE / TYPE 2 WIRELESS FACILITYWIRELESS FACILITY TYPE 2 Parent Project: PL15-0051 APPROVED This File: L15-0059 City of Tukwila Allan Ekberg, Mayor Department of Community Development - Jack Pace, Director NOTICE OF DECISION JANUARY 21, 2016 TO: Colin Robinson Centerline Solutions (obo T-MOBILE) 8210 154th Avenue NE Redmond, WA 98052 crobinson@centerlinesolutions.com This letter serves as a notice of decision and is issued pursuant to TMC 18.104.170 on the following project and permit approval. I. PROJECT INFORMATION Project File Number: L15-0059, PL15-0051 Applicant: Colin Robinson, Centerline Solutions (obo T-MOBILE) Type of Permit Applied for: Type 2 Wireless Telecommunications Facilities Permit Project Description: Approval of a Type II Wireless Telecommunication Facilities Permit to upgrade existing antennas, RRU radios, cabinet equipment, and associated cabling on an existing non -concealed building mounted wireless facility. No ground disturbance or expansion of the existing cabinet platform is proposed. Location: Tax Lot NO: 2623049021. This wireless facility is located at 16400 Southcenter Parkway, Tukwila, WA 98188. Associated Files: D15-0308 Comprehensive Plan Designation/Zoning District: Tukwila Urban Center/ Tukwila Urban Center - Regional Center (TUC -RC) II. DECISION SEPA Determination: The City SEPA Responsible Official has previously determined that this application does not require a SEPA threshold determination because it is categorically exempt. Tukwila City Hall • 6200 Southcenter Boulevard • Tukwila, WA 98188 • 206-433-1800 • Website: TukwilaWA.gov Page 2 1/21/2016 \\tukdata2k12\DCD Common$\Users\Laura\Wireless Facilities\L15-0059\L15-0059 SC Wireless NOD v2.docx Decision on Substantive Permit: The City Community Development Department has determined that the application for a Type 2 Wireless Communications Facility does comply with applicable City and state code requirements and has approved that application with the following conditions: 1. Revise Note on Site Plan Sheet A3.0 to state that it is a requirement for antennas and ancillary equipment to be painted to match the existing structure. 2. A business license is required as listed in TMC 18.58.070(2). Corresponding building permit shall not be issued until business license is issued. INFORMATIONAL ITEMS 1. The applicant is required to install emergency shut -down switch for Fire Department use. This can be a condition of approval of the corresponding building permit, D15-0308. Contact the Tukwila Fire Marshal at (206)575-4407 with any questions regarding this requirement. III. YOUR APPEAL RIGHTS The Decision on this Permit Application is a Type 2 decision pursuant to Tukwila Municipal Code §18.104.010. Other land use applications related to this project may still be pending. No administrative appeal of a DNS or an EIS is permitted. One administrative appeal to the City Hearing Examiner of the Decision on the Permit itself is permitted. If an MDNS was issued, any person wishing to challenge either the conditions which were imposed by the MDNS decision or the failure of the Department to impose additional conditions in the MDNS must raise such issues as part of the appeal to the Hearing Examiner. A party who is not satisfied with the outcome of the Hearing Examiner appeal process may file an appeal in King County Superior Court from the Hearing Examiner's decision. IV. PROCEDURES AND TIME FOR APPEALING In order to appeal the Community Development Director decision on the Permit Application, a written notice of appeal must be filed with the Department of Community Development within 14 days of the issuance of this decision. The requirements for such appeals are set forth in Tukwila Municipal Code ch. 18.116. All appeal materials shall be submitted to the Department of Community Development. Appeal materials MUST include: 1. The name of the appealing party. 2. The address and phone number of the appealing party` and if the appealing party is a corporation, association or other group, the address and phone number of a contact person authorized to receive notices on the appealing party's behalf. Phone: 206-433-1800 • Email: Mayor@TukwitaWA.gov • Website: TukwilaWA.gov Page 3 `J 1/21/2016 \\tukdata2k12\DCD Common$\Users\Laura\Wireless Facilities\L15-0059\L15-0059 SC Wireless NOD v2.docx 3. A statement identifying the decision being appealed and the alleged errors in the decision, including any specific challenge to an MDNS. 4. The Notice of Appeal shall identify (a) the specific errors of fact or errors in application of the law in the decision being appealed; (b) the harm suffered or anticipated by the appellant, and (c) the relief sought. The scope of an appeal shall be limited to matters or issues raised in the Notice of Appeal. 5. Appeal fee of $602 plus retainer. V. APPEAL HEARINGS PROCESS Any administrative appeal regarding the Permit shall be conducted as a closed record hearing before the Hearing Examiner based on the information presented to the Community Development Director, who made the original decision. No new evidence or testimony will be permitted during the appeal hearing. Parties will be allowed to present oral argument based on the information presented to the Community Development Director before their decision was issued. The Hearing Examiner's decision on the appeal is the City's final decision. Any party wishing to challenge the Hearing Examiner's decision on this application must file an appeal pursuant to the procedures and time limitations set forth in RCW ch. 36.70C. An appeal challenging a DNS, an MDNS or an EIS may be included in such an appeal. If no appeal of the Hearing Examiner's decision is properly filed in Superior Court within such time limit, the Decision on this permit will be final. The City's decision to issue a DNS, an MDNS or an EIS is final for this permit and any other pending permit applications for the development of the subject property. VI. INSPECTION OF INFORMATION ON THE APPLICATION Project materials including the application, any staff reports, and other studies related to the permits are available for inspection at the Tukwila Department of Community Development, 6300 Southcenter Blvd., Suite 100, Tukwila, Washington 98188 from Monday through Friday between 8:30 a.m. and 5:00 p.m. The project planner is Laura Benjamin, who may be contacted at 206-433-7166 or via email at laura.benjamin@tukwilawa.gov for further information. Property owners affected by this decision may request a change in valuation for their property tax purposes. Contact the King County Assessor's Office for further information regarding property tax valuation changes. Department of Community Development City of Tukwila Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov l • J eitq of J uPIwi&t Department Of Community Development AFFIDAVIT OF DISTRIBUTION I, Laura Benjamin, HEREBY DECLARE THAT: Notice of Application X Notice of Decision Notice of Public Hearing Notice of Public Meeting Determination of Non- Significance Mitigated Determination of Non - Significance Short Subdivision Agenda Determination of Significance & Scoping Notice Notice of Application for Shoreline Mgmt Permit Shoreline Mgmt Permit Board of Appeals Agenda Packet Board of Adjustment Agenda Packet Official Notice Notice of Action Other: Was mailed to each of the addresses listed/attached on this 21 st day of January, 2016 Project Name: SE04000B Southcenter Place Project Number: L15-0059 Associated File Number (s): PL15-0051 Mailing requested by: La ra Benjamin Mailer's signature 1.2----___. W:\USERS\LAURA\AFFIDAVIT OF DISTRIBUTION.DOC Colin Robinson (Applicant) crobinson@centerlinesolutions.com WA State Department of Ecology - SEPA Unit sepaunit@ecy.wa.gov King County Assessor's Office Accounting Division 500 Fourth Avenue, Room 709A Seattle, WA 98104 W:\USERS\LAURA\AFFIDAVIT OF DISTRIBUTION.DOC •7 \ i City of Tukwila Allan Ekberg, Mayor Department of Community Development— Jack Pace, Director NOTIFICATION: FILE NUMBER: APPLICANT: PROPERTY OWNER: REQUEST: LOCATION: ASSOCIATED PERMITS: SEPA DETERMINATION: COMPREHENSIVE PLAN DESIGNATION: ZONE DESIGNATION: STAFF: ATTACHMENTS: STAFF REPORT TO THE DIRECTOR PREPARED JANUARY 21, 2016 Notification is not required for a Type II land use application. L15-0059, PL15-0051 Colin Robinson, Centerline Solutions (obo T-MOBILE) Legacy Partners Commercial Approval of a Type II Wireless Telecommunication Facilities Permit to upgrade existing antennas, RRU radios, cabinet equipment, and associated cabling on an existing non -concealed building mounted wireless facility. No ground disturbance or expansion of the existing cabinet platform is proposed. Tax Lot NO: 2623049021. This wireless facility is located at 16400 Southcenter Parkway, Tukwila, WA 98188. Electrical permits issued through the City of Tukwila will be required for service alteration for any other electrical service work this is anticipated but not noted on the plans, per article 85.13 (B), Washington electrical code. A building permit is required for the scope of work stated on the submitted plans. Building permit application D15-0308 received at time of this application. Exempt Tukwila Urban Center Tukwila Urban Center — Regional Center (TUC -RC) Laura Benjamin, Assistant Planner Project Plans for Permit L15-0059 Tukwila City Hall • 6200 Southcenter Boulevard • Tukwila, WA 98188 • 206-433-1800 • L4 ebsite: TukwilaWA.gov Page 2 1/21/2016 W:\Users\Laura\Wireless Facilities\L15-0059\L15-0059 SC Wireless SR.docx FINDINGS Vicinity/Site Information Project Description The applicant is requesting approval of a Type II Wireless Telecommunication Facilities [WCF] Permit to replace and add equipment on an existing non -concealed building mounted facility at 16400 Southcenter Parkway. The project includes: • Removal of 2 existing panel antennas and addition of three new panel antennas. • Addition of 1 FRIG RRU radio. • Addition of 1 FXFC RRU radio. • Addition of cabinet equipment including 6 diplexers, 2 FSMF, 2 FBBC, and 1 ESMB. The existing non -concealed building mounted cellular facility extends beyond the roofline. The proposed modifications do not alter the existing height and is below the 85 foot maximum height without incentives in the TUC -RC. Existing Development This non -concealed building mounted wireless facility is located on the Legacy Southcenter Place, an office building located in the Southcenter (Tukwila Urban Center) area. Surrounding Land Uses The subject property is zoned TUC -RC. The surrounding parcels to the south and east are zoned Tukwila Urban Center — Pond (TUC-P). The property fronts Southcenter Parkway. To the west of Southcenter Parkway, the parcels are zoned Tukwila Urban Center — Commercial Corridor (TUC -CC). To the north, across Strander Boulevard, the properties are also zoned TUC -RC. BACKGROUND In 2006, the City adopted a Wireless Facilities Chapter (TMC 18.71) to the Zoning Code. The chapter provides specific location and design requirements for the placement of WCF within the City of Tukwila. The WCF being modified was originally approved by the City in 1998 (L98-0016) through a conditional use permit. In 1998 the WCF was approved for modifications (L98-0023) through a conditional use permit. In 2008 the WCF was approved for modifications (L08-047) through a Type 2 Wireless Facilities permit. Location Selection Tukwila Municipal Code (TMC) provides a hierarchy of appropriate locations within the City. Generally, co - locations and utilizing existing structures are favored over the development of new standalone WCF within the City. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov �i Page 3 1/21/2016 W:\Users\Laura\Wireless Facilities\L15-0059\L15-0059 SC Wireless SR.docx TABLE A Type of Permit Required, Based on Type of Wireless Communication Facility ZONING (1) TYPE OF FACILITY RESIDENTIAL COMMERCIAL INDUSTRIAL Transmission Tower co -location Type 1 Type 1 Type 1 Adding antennas to an existing tower Type 1(2) Type 1(2) Type 1(2) Utility pole co -location Type 2 Type 2 Type 2 Concealed building attached Type 2(3) Type 2(3) Type 2(3) Non -concealed building attached Type 2 Type 2 Type 1 New tower or waiver request Type 4 Type 4 Type 4 (1) Zoning for any private/public property or right-of-way Residential — LDR, MDR, or HDR Commercial — O, MUO, RCC, NCC, RC, RCM, TUC, C/LI or TVS Industrial - LI, HI, MIC/L, or MIC/H (2) Provided the height of the tower does not increase and the square footage of the enclosure area does not increase. (3) An applicant may request to install a non -concealed building attached facility, under TMC Section 18.58.150. The applicant is replacing antennas and radios and installing new cabinet equipment to an existing non - concealed building mounted wireless facility. This decision does not require the use of any new facilities for placement of the new antennas, radios, and cabinet equipment. The proposed new cabinet equipment will be located on an existing platform. Design Standards The City provides specific design standards for the placement of WCF within the City of Tukwila. The table below indicates if the applicant's proposal complies with required standards. Table 1 (See TMC 18.58.070 for further details) General Requirements Project does comply Project does not comply Not Applicable Notes 1. Generators or other devices which will create noise must comply with TMC 8.22 regarding noise. X The applicant has not proposed a new generator. 2.Business License Requirement X T-MOBILE is in the process of applying for a business license. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov Page 4 1/21/2016 W:\Users\Laura\Wireless Facilities\L15-0059\L15-0059 SC Wireless SR.docx 3. Only safety signage must be placed on the WCF. X The applicant does not propose any signage. 4. Accommodations for parking for maintenance personal must be provided. X Parking is not affected by this modification. 5. Towers shall either maintain a galvanized steel finish or be painted a neutral color so as to reduce its visual obtrusiveness. X The applicant has not proposed a new tower. The existing facility is a non -concealed building mounted facility and does not include a tower. 6. The design of all buildings and ancillary structures shall use materials, colors, textures, screening, and landscaping that will blend the tower facilities to the natural setting and built environment. X No new buildings or structures are proposed. 7. Antennas shall have the same color scheme as the structure they are located on. X No change to the color of the existing antennas and equipment is proposed. The current equipment color blends with the color of the building walls. New antennas and radios shall be painted to match the walls. 8. WCF poles and towers shall only have safety lights if required by a government agency. X No lighting is proposed. 9. No advertising is permitted on WCF X No advertising is proposed. 10. Each service provider shall be limited to an equipment enclosure of 360 square feet. X No change to the existing equipment enclosure is proposed. Table 2 (See TMC 18.58.110 for additional information) Adding Antennas to Existing Project Project Not Notes WCF Tower -Specific does does Applicable Development Standards comply not comply Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov \_/ Page 5 1/21/2016 W:\Users\Laura\Wireless Facilities\L15-0059\L15-0059 SC Wireless SR.docx 1. The proposed facility must meet the height requirements of the applicable zoning category. If the building where the facility is located is at or above the maximum height requirements, the antennas are permitted to extend a maximum of 3 feet above the existing roof line. X No proposed changes to the height of the facility. The facility current extends 17 feet above the roofline and is below the 85 foot height maximum for the TUC -RC zone. 2. Antennas shall be painted to match the color scheme of the building(s). X The antennas and radios are to be painted to match the building walls. 3. Feed lines and cables should be located below the parapet of the rooftop. If the feed lines and cables must be visible, they must be painted to match the color scheme of the building(s). X All cables will follow existing routes along the roof top, below the parapet. 4. If cabinet equipment cannot be located within the building where the wireless communication facilities will be located, then it must be located on the rooftop of the building. If screening is required, then the proposed screening must be consistent with the existing building in terms of color, style, architectural style and material. If the cabinet equipment is to be located on the ground, the equipment must be fenced with a 6-foot-tall fence and materials shall be used to screen the equipment from view. X Proposed cabinet equipment will be placed on the existing steel platform. The plans do not propose an expansion of the existing steel platform. There are no proposed changes to the height of the cabinet. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov Page 6 1/21/2016 W:\Users\Laura\Wireless Facilities\L15-0059\L15-0059 SC Wireless SR.docx CONCLUSIONS 1. The proposed modifications to the existing WCF will not significantly alter the conditions that currently exist and will not be materially detrimental to the public welfare or injurious to property or improvements in the vicinity. 2. As demonstrated in Tables 1 and 2, the project meets all applicable development standards for a Type 2 WCF. 3. The proposed modifications will not alter the surrounding land uses in terms of traffic and pedestrian circulation, building or site design. 4. The proposed project is in keeping with the goals and policies of the Comprehensive Land Use Policy Plan. RECOMMENDATIONS The recommendation to the Director of Community Development is to approve this application for a Type I Wireless Telecommunication Facility permit as applied for by Centerline Solutions for T-MOBILE with the following conditions: 1. Revise Note on Site Plan Sheet A3.0 to state that it is a requirement for antennas and ancillary equipment to be painted to match the existing structure. 2. A business license is required as listed in TMC 18.58.070(2). Corresponding building permit shall not be issued until business license is issued. INFORMATIONAL ITEMS 1. The applicant is required to install emergency shut -down switch for Fire Department use. This can be a condition for approval of the corresponding building permit, D15-0308. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov 0400 City of Tukwila Department of Community Development File Number L15-0059, PL15-0051 LAND USE PERMIT ROUTING FORM TO: II Building Planning ❑I Public Works I❑I Fire Dept. Police Dept. 101 Parks/Rec Project: SE04000B Southcenter Place Address: 16400 Southcenter Parkway Date transmitted: 12/21/2015 Response requested by: 1/11/2015 Staff coordinator: Laura Benjamin Date response received: REVIEWERS: Please specify how the attached plans conflict with your ADOPTED development regulations, including citations. Be specific in describing the types of changes you want made to the plans. When referencing codes, please identify the actual requirement and plan change needed. The Planning Division review does not supplant each department's ability to administer its own regulations and permits. However, project consistency at the Planning review stage is important to minimize significant later design changes. More than minimal design changes require further Planning Commission review, even if alteration is required to satisfy a City requirement. This further review is typically a minimum 60-day process. Requirements based on SEPA (e.g., not required by an adopted development regulation) MUST identify the impact being mitigated, the policy basis for requiring mitigation, and the method used to calculate the mitigation required. Calculations of project impacts and the mitigation required (e.g., water capacity, road level of service analyses, or turning analyses) may be required of the applicant. COMMENTS (Attach additional comment sheets and/or support materials as needed.) Ab uu,au4e.(4_43- of +4-1s Plan check date: Z, _ IS Comments prepared by: Update date: 0400 City of Tukwila Department of Community Development ECEIVF DEC 212015 TUKVVII PUBLIC WORKS File Number L15-0059, PL15-0051 LAND USE PERMIT ROUTING FORM TO: ID Building I❑I Planning S Public Works ID Fire Dept. ID Police Dept. Parks/Rec Project: SE04000B Southcenter Place Address: 16400 Southcenter Parkway Date transmitted: 12/21/2015 Response requested by: 1/11/2015 Staff coordinator: Laura Benjamin Date response received: REVIEWERS: Please specify how the attached plans conflict with your ADOPTED development regulations, including citations. Be specific in describing the types of changes you want made to the plans. When referencing codes, please identify the actual requirement and plan change needed. The Planning Division review does not supplant each department's ability to administer its own regulations and permits. However, project consistency at the Planning review stage is important to minimize significant later design changes. More than minimal design changes require further Planning Commission review, even if alteration is required to satisfy a City requirement. This further review is typically a minimum 60-day process. Requirements based on SEPA (e.g., not required by an adopted development regulation) MUST identify the impact being mitigated, the policy basis for requiring mitigation, and the method used to calculate the mitigation required. Calculations of project impacts and the mitigation required (e.g., water capacity, road level of service analyses, or turning analyses) may be required of the applicant. COMMENTS (Attach additional comment sheets and/or support materials as needed„) have n� cmuwtet,;;9s Plan check date: V2-1 7:2A t Comments prepared by: Update date: 0400 TO: City of Tukwila Department of Community Development File Number L15-0059, PL15-0051 LAND USE PERMIT ROUTING FORM Building $ Planning Public Works Fire Dept. Police Dept. Parks/Rec Project: SE04000B Southcenter Place Address: 16400 Southcenter Parkway Date transmitted: 12/21/2015 Response requested by: 1/11/2015 Staff coordinator: Laura Benjamin Date response received: REVIEWERS: Please specify how the attached plans conflict with your ADOPTED development regulations, including citations. Be specific in describing the types of changes you want made to the plans. When referencing codes, please identify the actual requirement and plan change needed. The Planning Division review does not supplant each department's ability to administer its own regulations and permits. However, project consistency at the Planning review stage is important to minimize significant later design changes. More than minimal design changes require further Planning Commission review, even if alteration is required to satisfy a City requirement. This further review is typically a minimum 60-day process. Requirements based on SEPA (e.g., not required by an adopted development regulation) MUST identify the impact being mitigated, the policy basis for requiring mitigation, and the method used to calculate the mitigation required. Calculations of project impacts and the mitigation required (e.g., water capacity, road level of service analyses, or turning analyses) may be required of the applicant. COMMENTS (Attach additional comment sheets and/or support materials as needed.) Comnrert- 1,14-_-1 Plan check date: Comments Update date: prepared by: Teri Svedahl From: Teri Svedahl Sent: Friday, December 11, 2015 3:01 PM To:'crobinson@centerlinesolutions.com' Subject: SE04000B Southcenter Place Wireless Facility application Colin — Thank you for coming in today to submit for the Type II Wireless land use application — file # L15- 0059. As discussed, the fee for Type II is $1760.85. This can be confirmed on the City website under Planning Division and Land Use permits and fee schedule. The check submitted for payment was in the amount of $620.55 — this is the fee for a Type I. There is a balance owing of $1140.30 You can mail in the payment to my attention at the address below. Please reference file L15-0059 to expedite processing of payment and to continue review of your permit application. Sincerely, Teri, svedahl„ Adwc.%vastrative <support Teclivt,iciah, City of Tukwila Department of Community Development 6300 Southcenter Blvd, Ste 100 Tukwila WA 98188 Please be aware all City email is subject to public disclosure i `'CENTERLINE DEC 112015 Community Development December 11, 2015 Department of Community Development 6300 Southcenter Blvd., #100 Tukwila, WA 98188 Re: T-Mobile Wireless Communications Facility (WCF) T-Mobile Site Name: SE04000B South Center Place Site Address: 16400 South Center Parkway Tukwila, WA 98188 Parcel Number: 2623049021 To Whom It May Concern: Oh behalf of T-Mobile, Centerline Solutions is pleased to submit a Type II Zoning Application and Building Permit Application for a modification of an existing non concealed building attached wireless communications facility. The proposed modification consists of changes to the existing rooftop site. The modifications will consist of the removal of 2 existing panel antennas, addition of 3 new panel antennas, addition of 1 FRIG RRU, 1 FXFC RRU, 6 Diplexers and 2 FSMF, 2 FBBC and 1 ESMB within the existing cabinet. Please find enclosed: Application Checklist WCF Application Form Building Permit Application Form Construction Drawings Structural Analysis NIER Study Photo Simulations Check number 0003213286 for $620.55 and Check number 0003213285 $824.42 This modification meets the Tukwila Municipal Code §18.58 requirements for a Type II Wireless Modification. This modification is exempt from SEPA per WAC 197-11-800 (25) (a)(i). The site does not include any sensitive areas per NWMaps.net and all equipment is on the roof. No generator is located at the site and none is proposed. The site is unscreened so a screening board is not applicable. The site is on a rooftop so a landscaping plan is not applicable. Antennas will be painted to match the building with a neutral color. A letter from a radio frequency engineer is attached. The facility is not located within a residential zone, it is zoned TUC. 8210 154th Avenue NE, Suite 120 Redmond, WA 98052 'CENTERLINE 18.58.070 General Requirements. The following shall apply to all wireless communication facilities regardless of the type of facility: 1. Noise — Any facility that requires a generator or other device which will create noise must demonstrate compliance with TMC Chapter 8.22, "Noise". A noise report, prepared by an acoustical engineer, shall be submitted with any application to construct and operate a wireless communication facility that will have a generator or similar device. The City may require that the report be reviewed by a third party expert at the expense of the applicant. Applicant Response: This site does not include a generator and none is proposed. 2. Business license requirement — Any person, corporation or entity that operates a wireless communication facility within the City shall have a valid business license issued annually by the City. Any person, corporation or other business entity which owns a tower also is required to obtain a business license on an annual basis. Applicant Response: A business license application is pending. 3. Signage — Only safety signs or those mandated by other government entities may be located on wireless communication facilities. No other types of signs are permitted on wireless communication facilities. Applicant Response: Acknowledged. Only signs mandated by government entities will be located on the WCF. 4. Parking — Any application must demonstrate that there is sufficient space for temporary parking for regular maintenance of the proposed facility. Applicant Response: The site is located on top of an office building surrounded by ample parking. 5. Finish — A tower shall either maintain a galvanized steel finish or, subject to any applicable standards of the FAA or FCC, be painted a neutral color so as to reduce its visual obtrusiveness. TITLE 18 — ZONING Produced by the City of Tukwila, City Clerk's Office Page 18-217 Applicant Response: Not applicable — this is a building mounted facility rather than a tower mounted facility. Antennas will be painted with a neutral color. 6. Design —The design of all buildings and ancillary structures shall use materials, colors, textures, screening and landscaping that will blend the tower facilities with the natural setting and built environment. Applicant Response: Antennas will be painted to match the existing building. No new building proposed. 8210 154th Avenue NE, Suite 120 Redmond, WA 98052 CENTERLINE 7. Color — All antennas and ancillary facilities located on buildings or structures other than towers shall be of a neutral color that is identical to or closely compatible with the color of the supporting structure so as to make the antenna and ancillary facilities as visually unobtrusive as possible. Applicant Response: Antennas will be painted to match the building in a neutral color. 8. Lighting — Towers shall not be artificially lighted unless required by the FAA, FCC or other applicable authority. If lighting is required, the reviewing authority shall review the lighting alternatives and approve the design that would cause the least disturbance to the surrounding areas. No strobe lighting of any type is permitted on any tower. Applicant Response: No lighting is proposed or required by the FAA or FCC. 9. Advertising — No advertising is permitted at wireless communication facility sites or on any ancillary structure or facilities equipment compound. Applicant Response: There is no existing or proposed advertising. 10. Equipment Enclosure — Each applicant shall be limited to an equipment enclosure of 360 square feet at each site. However, this restriction shall not apply to enclosures located within an existing commercial, industrial, residential or institutional building. Applicant Response: The equipment is on the roof of a building, there is no Equipment Enclosure. 18.58.110 Non -concealed Building Mounted Development Requirements. The following requirements shall apply: 1. Height — The proposed facility must meet the height requirements of the applicable zoning category. If the building where the facility is located is at or above the maximum height requiirements, the antennas are permitted to extend a maximum of 3 feet above the existing roof line. Non -concealed building mounted facilities shall not qualify as "Rooftop Appurtenances" under TMC 18.50.080. Applicant Response: The existing facility meets the 85' TUC -RC height limit and no height increase is proposed. 2. Antenna aesthetics — The first preference for any proposed facility is to utilize flush -mounted antennas. Nonflushmounted antennas may be used when their visual impact will be negated by the scale of the antennas to the building. "Shrouds" are not required unless they provide a better visual appearance than exposed antennas. Antennas shall be painted to match the color scheme of the building(s). Applicant Response: The antennas will be painted to match the color scheme of the building. Please see attached photo sims. 8210 154th Avenue NE, Suite 120 Redmond, WA 98052 'CENTERLINE 3. Feed lines and coaxial cables — Feed lines and cables should be located below the parapet of the rooftop. If the feed lines and cables must be visible, they must be painted to match the color scheme of the building(s). Applicant Response: All cables will be located below the parapet of the rooftop. 4. Cabinet equipment — If cabinet equipment cannot be located within the building where the wireless communication facilities will be located, then it must be located on the rooftop of the building. If the equipment can be screened by placing the equipment below the parapet walls, no additional screening is required. If screening is required, then the proposed screening must be consistent with the existing building in terms of color, style, architectural style and material. If the cabinet equipment is to be located on the ground, the equipment must be fenced with a 6-foot-tall fence and materials shall be used to screen the equipment from view. Barbed wire may be used in the TVS, LI, HI, MIC/L, and MIC/H zones. (Ord. 2135 §1 (part), 2006) Applicant Response: The cabinets are located on the rooftop of the building. No new cabinets are proposed. Please see the attached photo simulations. If you have any questions or inquiries regarding this application please feel free to contact me. Thank you, Colin Robinson Zoning Specialist 8210 154th Avenue NE, Suite 120 Redmond, WA 98052 8210 154th Avenue NE, Suite 120 Redmond, WA 98052 P C99VF DEC 1I �01� E T E R L I N E Community Development RF Safety and NIER Analysis Report RECEE WF", 12/08/2015 DEC 212015 TUKVvtu-, Site: SE04000B PUBLIC WORKS Prepared for: T-Mobile Prepared for: T-Mobile, Site: SE04000B Table of Contents Certification 3 Executive Summary 4 Introduction 6 Site Details 6 Predictive Analysis Details 9 Conclusions and Recommendations 13 Appendix A: FCC Compliance and RF Safety Policies 14 Appendix B: Overview of RoofView® Functions and Assumptions 16 References 18 Limited Warranty 18 Centerline Solutions, Inc. Proprietary and Confidential Page 2 of 18 Prepared for: T-Mobile, Site: SE04000B Certification This report, prepared by Centerline Solutions, LLC for T-Mobile, is intended to document compliance and evaluate power density levels as outlined in the report. The computations, analysis, and resulting report and conclusions were based on applicable FCC guidelines and regulations for maximum permissible exposure to humans consistent with FCC OET Bulletin 65, Edition 97-01. Additionally, Centerline Solutions, LLC certifies that the assumptions are valid and that the data used within Centerline Solutions' control are accurate, including information collected as part of Centerline Solutions' field surveys. Centerline Solutions, LLC does not however certify the accuracy or correctness of any data provided to Centerline Solutions, LLC for this analysis and report by T-Mobile or other third parties working on behalf of T-Mobile. I certify that the attached RF exposure analysis and report is correct to the best of my knowledge, and all calculations, assumptions and conclusions are based on generally acceptable engineering practices: EXPIRES 2/22/2016 Patrick A. Kearns, P.E. 12/08/2015 Centerline Solutions, Inc. Proprietary and Confidential Page 3 of 18 Prepared for: T-Mobile, Site: SE04000B Executive Summary This report provides the results of an RF power density analysis performed for T-Mobile at Site SE04000B. Current Site Configuration: Three sector site operating with technology including GSM in PCS band (1900 MHz), UMTS in PCS (1900 MHz band), UMTS in AWS (2100 MHz), LTE in AWS band (2100 MHz), and LTE in the 700 MHz band. Proposed Site Configuration: Modification in the current Gamma sector configuration and applying a sector split. Four sector site operating with technology including GSM in PCS band (1900 MHz), UMTS in PCS (1900 MHz band), UMTS in AWS (2100 MHz), LTE in AWS band (2100 MHz), and LTE in the 700 MHz band. Scope of Work: The proposed physical modifications will result in replacing antennas and radio hardware at this site. Rooftop Equipment Modifications: • Removal of (3) existing panel antennas • Addition of (3) panel antennas • Addition of (1) FRIG • Addition of (1) FXFC • Addition of (8) Diplexer • Addition of (2) FSMF (2) FBBC, & (1) ESMB in (E) cabinet Site Description: • Site Type and Height- Rooftop, elevation of 73.0 ft. AGL • Equipment Location- Adjacent to the antennas. • Other Antennas- There are 8 Verizon antennas and a microwave dish. Also, there are several satellite dishes. • Access- The only access to the site is through the locked door leading to the rooftop. • Study Reference Location- This study examines the power density environment at ground, rooftop, and penthouse levels from ALL sources of RF radiation, except for those antennas specifically excluded as described in the Introduction section. • Existing Signage- There are blue RF signs and a yellow RF guideline sign placed at the interior side of the door that leads to the rooftop of the building. Also, there are barriers with blue Notice signs around Verizon's antennas. Centerline Solutions, Inc. Proprietary and Confidential Page 4 of 18 Prepared for: T-Mobile, Site: SE04000B • RF Environment- For purposes of evaluating compliance with FCC OET Bulletin 65, the area on the ground level is considered to be an uncontrolled/public environment. However, the areas on the rooftop and penthouse levels are considered to be controlled/occupational environments. Analysis: The analysis of the RF power density at this site indicates that emissions on the ground will not exceed the FCC's MPE limit for General Public environments. T-Mobile's contribution to the rooftop level exposures is calculated to be less than 28.2% of the FCC MPE limit for Occupational/Controlled environments. The rooftop level exposures near Verizon's Beta sector antennas are calculated to be less than 122.9% of the FCC MPE limit for Occupational/Controlled environments. However, Verizon has mitigated the risk of accidental exposure by placing barriers and RF signs. Conclusion and Recommendations: • The results of the analysis indicate that the power density levels at the ground will not exceed the FCC MPE General Population limit with the proposed antenna plan. • The results of the analysis indicate that the power density levels on the main building rooftop contributed by T-Mobile will not exceed the FCC MPE Occupational limit with the proposed antenna plan. • The results of the analysis indicate that the power density levels on the north penthouse (Penthouse 2) may exceed the FCC MPE Occupational limit with the proposed antenna plan. However, Penthouse 2 is not generally accessible. • Centerline Solutions recommends placing blue RF signs on the wall of the south penthouse (Penthouse 1), adjacent to the antennas of the Gamma sector. In addition, Centerline Solutions recommends placing yellow RF signs near the top of the roof and on each side of the north penthouse (Penthouse 2). See Exhibits 5 and 6 for recommended signage locations. • By taking the above mentioned recommended actions, this site will operate in general compliance with the FCC's OET Bulletin 65. Centerline Solutions, Inc. Proprietary and Confidential Page 5 of 18 Prepared for: T-Mobile, Site: SE04000B Introduction The purpose of this analysis and report is to evaluate the cumulative power density levels of all antennas located on the building rooftop and identify any areas of concern that require mitigation. This report also assesses the rooftop's compliance with FCC OET Bulletin 65; "Guidelines for Human Exposure to Radio -frequency Electromagnetic Fields". As part of this analysis, the site was visited on 11/17/2015 to perform a complete field survey. The purpose of the survey was to verify antennas located on the building rooftop and identify co -located wireless facilities. The power density simulation performed for this site utilized RoofView® analysis software. All antennas were assigned an operating frequency and transmit power and were deemed to be operating at 100% of their rated output power. The microwave dish antenna located on Verizon's Alpha sector and other satellite dishes were not included in the analysis, as their beamwidth is very narrow, and very little of their radiated energy is propagated to the rooftop level below the antenna. Site Details Address: 16400 South Center Park Way Tukwila, WA 98188 Site type: Building Height: — 73.0 ft. AGL The photographs on the following pages show a view of the existing antennas on the rooftop and RF signage that is present. Centerline Solutions, Inc. Proprietary and Confidential Page 6 of 18 Prepared for: T-Mobile, Site: SE04000B r , • i or I'JORMATlQN ROOF ACCESS Exhibit 1- Photos Centerline Solutions, Inc. Proprietary and Confidential Page 7 of 18 Prepared for: T-Mobile, Site: SE04000B Exhibit 2- Photos (Verizon's sectors) Centerline Solutions, Inc. Proprietary and Confidential Page 8 of 18 Prepared for: T-Mobile, Site: SE04000B Antenna Inventory: The following table contains the technical data used to simulate the power density that may be encountered with all antennas simultaneously operating at full rated power. D Name (MHz) Freq Trans Power Trans Count Other Loss Calc Power Mfg Model (ft) Z(Ground) (ft) Z(Rooftop) (ft) Z(Penthouse) Type (ft) Aper dad Gan BWdth Ptt3r TMA1A L2100 2150.00000 120.0 1 0.5 107.0 Comrficope TMBXX-6516-R2M 76.4 13.6 3.4 DBQuad 4.9 15.35 65;130 TMA2A G1900 1950.00000 20.0 2 0.5 35.7 ComrScope SBNFI1-+1D65B 75.2 12.4 2.2 Hexport 6.1 16.05 66;130 TMA2B U1900 1950.00000 30.0 2 0.5 53.5 ConrrScope SBNI#1D65B 752 12.4 2.2 Hexport 6.1 16.05 66;130 TMA2C U2100 2150.00000 40.0 1 2.0 25.2 ConrrScope SBNF I-1D65B 75.2 12.4 2.2 Hexport 6.1 16.45 63;130 TMA2D L700 730.00000 40.0 1 0.5 35.7 CormScope SBNI#1D65B 75.2 12.4 2.2 Hexport 6.1 12.75 68;130 TMB1A L2100 2150.00000 120.0 1 0.5 107.0 ComrScope TMBXX-6516-R2M 76.4 13.6 3.4 DBQuad 4.9 15.35 65;220 TMB2A G1900 1950.00000 20.0 2 0.5 35.7 CorrrScope SBNI1+10658 75.2 12.4 2.2 Hexport 6.1 16.05 66;220 TMB2B U1900 1950.00000 30.0 2 0.5 53.5 Conrr6cope SBNI-A+1D65B 75.2 12.4 2.2 Hexport 6.1 16.05 66;220 TMB2C U2100 2150.00000 40.0 1 2.0 25.2 ComrScope SBNH-1D65B 75.2 12.4 2.2 Hexport 6.1 16.45 63;220 TMB2D L700 730.00000 60.0 1 0.5 53.5 ComrScope SBNI#1D65B 75.2 12.4 2.2 Hexport 6.1 12.75 68;220 TMC1A G1900 1950.00000 20.0 2 0.5 35.7 ComnScope 1-13XX-3319DS-A2M 76.6 13.8 3.6 Quad 4.8 18.45 35;310 TMC1B U1900 1950.00000 30.0 2 0.5 53.5 CormScope 1-13XX-3319DS-A2M 76.6 13.8 3.6 Quad 4.8 18.45 35;310 TMC1C 12100 2150.00000 120.0 1 0.5 107.0 Corrr6cope I-BXX-33191:6-A2M 76.6 13.8 3.6 Quad 4.8 18.65 34;310 TMC2A U2100 2150.00000 40.0 1 2.0 252 ComrScope DBXNH-6565E-A2M 75.2 12.4 2.2 DBQuad 6.1 16.05 63;340 TMC2B L700 730.00000 60.0 1 0.5 53.5 ConanScope DBXNH-6565E-A2M 75.2 12.4 2.2 DBQuad 6.1 13.05 71;340 TMD1A G1900 1950.00000 20.0 2 0.5 35.7 ComrScope FBXX-3319DS•A2M 76.6 13.8 3.6 Quad 4.8 18.45 35;20 TMO1B U1900 1950.00000 30.0 2 0.5 53.5 ComrScope FBXX-3319D5-A2M 76.6 13.8 3.6 Quad 4.8 18.45 35;20 TMD1C L2100 2150.00000 120.0 1 0.5 107.0 Corm$cope FBXX-3319DS-A2M 76.6 13.8 3.6 Quad 4.8 18.65 34;20 VZA1A L700 730 60 1 2.0 37.86 Anphenol BXA-70063-8CF®N 67.1 4.3 -5.9 X-Pole 7.89 15.45 65;15 VZA4A C850 850 20 8 2.0 101 Arrphenol BXA-70063-8CF®N 67.6 4.8 -5.4 X-Pole 7.89 15.45 65;15 VZA2A L2100 2150 60 2 0.5 107 Anphenol CWWX063X19x00 69.3 6.5 -3.8 X-Pole 6.25 14.85 67;15 VZA3A C1900 1950 16 3 3.0 24.06 Arrphenol CWWX063X19x00 69.3 6.5 -3.8 X-Pole 6.25 15.05 66;15 VZB1A C850 850 20 8 2.0 101 Arrphenol BXA-70063-8CF®1N 67.1 4.3 -5.9 X-Pole 7.89 15.45 65;190 VZB4A L700 730 60 1 2.0 37.86 Arrphenol BXA-70063-8CFB7N 67.6 4.8 -5.4 X-Pole 7.89 15.45 65;190 VZB2A C1900 1950 16 3 3.0 24.06 Anphenol CWWX063X19x00 69.3 6.5 -3.8 X-Pole 6.25 14.85 67;190 VZB3A L2100 2150 60 2 0.5 107 Arrphenol CWWX063X19x00 69.3 6.5 -3.8 X-Pole 6.25 15.05 66;190 Exhibit 3- Antenna Details Predictive Analysis Details For purposes of this analysis, RoofView® was configured to provide an output based on the appropriate MPE limit(s) published in the FCC's guidelines. The antenna information was loaded into RoofView®, an MPE predictive analysis tool by Richard Tell and Associates, Inc. The analysis was run for the ground, building rooftop, and penthouse levels. The following exhibits show the calculated RF emissions at these levels. Exhibit 4 shows the RF emissions at ground level, Exhibit 5 shows the RF emissions at the rooftop level, and Exhibit 6 shows the RF emissions at the penthouse level. The solid green shading indicates that power density levels are expected to be less than 5% of the applicable MPE level in these areas. Other colors are defined in the legends below. Centerline Solutions, Inc. Proprietary and Confidential Page 9 of 18 Prepared for: T-Mobile, Site: SE04000B Ground Ground Level • rruund Greer; <= 5% General Population Limit Blue <= 20% General Population Limit <= 100% General Population Limit Red > 100% General Population Limit Exhibit 4- % MPE General Population Ground Level (Not to scale) Page 10 of 18 Prepared for: T-Mobile, Site: SE04000B North Verizon Rooftop Rooftop Level Green <= 5% Occupational Limit Blue <= 20% Occupational Limit <= 100% Occupational Limit Red > 100% Occupational Limit Exhibit 5- % MPE Occupational Building Rooftop Level (Not to scale) Page 11 of 18 Prepared for: T-Mobile, Site: SE04000B Grourd Penthouse Level f;reeu <= 5% Occupational Limit Blue <= 20% Occupational Limit <= 100% Occupational Limit Red > 100% Occupational Limit Exhibit 6- % MPE Occupational Penthouse Level (Not to scale) Page 12 of 18 Prepared for: T-Mobile, Site: SE04000B Conclusions and Recommendations • The results of the analysis indicate that the power density levels at the ground will not exceed the FCC MPE General Population limit with the proposed antenna plan. • The results of the analysis indicate that the power density levels on the main building rooftop contributed by T-Mobile will not exceed the FCC MPE Occupational limit with the proposed antenna plan. • The results of the analysis indicate that the power density levels on the north penthouse (Penthouse 2) may exceed the FCC MPE Occupational limit with the proposed antenna plan. However, Penthouse 2 is not generally accessible. • Centerline Solutions recommends placing blue RF signs on the wall of the south penthouse (Penthouse 1), adjacent to the antennas of the Gamma sector. In addition, Centerline Solutions recommends placing yellow RF signs near the top of the roof and on each side of the north penthouse (Penthouse 2). See Exhibits 5 and 6 for recommended signage locations. • By taking the above mentioned recommended actions, this site will operate in general compliance with the FCC's OET Bulletin 65. Note: Modifications to the site; and/or increases in channel counts or power levels exceeding those listed in this report will require additional evaluation to determine compliance. Page 13 of 18 Prepared for: T-Mobile, Site: SE04000B Appendix A: FCC Compliance and RF Safety Policies In August of 1997, the FCC published OET Bulletin 65 Edition 97-01 to regulate methods for evaluating compliance with FCC guidelines for human exposure to radiofrequency (RF) electromagnetic fields. The FCC guidelines for human exposure to RF electromagnetic fields incorporate two categories of limits; namely "Controlled" (a.k.a. Occupational) and "Uncontrolled" (a.k.a. General Public). The guidelines offer suggested methods for evaluating fixed RF transmitters to insure that the controlled and uncontrolled limits deemed safe by the FC for human exposure are not exceeded. OET Bulletin 65 recommended guidelines are intended to allow an applicant to "make a reasonably quick determination as to whether a proposed facility is in compliance with the limits." In addition, the guidelines offer alternate supplementary considerations and procedures such as field measurements and more detailed analysis that should be used for multiple emitter situations. These guidelines define RF as emissions in the frequency range of 300 kHz to 100 GHz. The FCC define Maximum Permissible Exposure (MPE) limits within this frequency range based on limits recommended by the National Council on Radiation Protection and Measurement, the Institute of Electrical and Electronics Engineers (IEEE), and by the American National Standards Institute (ANSI). The specific MPE limits defined by the FCC are as follows: Frequency Range [MHz] 0.3 - 3.0 3.0 - 30 30 - 300 300 -1,500 1,500 - 100,000 Limits for Occupational/Controlled Exposure Electric Field Strength (E) [V/m] 614 1842/f 61.4 Magnetic Field Strength (H) [A/m] 1.63 4.89/f 0.163 Power Density (S) [mW/Cm"2] 100* 900/f^2* 1 f/300 5 Averaging Time IEI"2, CHI"2 or S [minutes] 6 6 6 6 6 Frequency Range [MHz] 0.3 - 3.0 3.0 - 30 30 - 300 300 -1,500 1,500 -100,000 Electric Field Strength (E) [V/m] 614 842/f 27.5 Limits for General Population/Uncontrolled Exposure Magnetic Field Power Density Averaging Time IEI"2, Strength (H) [Alm] (S) [mW/Cm"2] IHI"2 or S [minutes] 1.63 100* 30 2.19/f 180/f^2* 30 0.073 0.2 30 f/1500 30 1 30 f = frequency *Plane -wave equivalent power density The FCC states that "Occupational/Controlled limits apply in situations in which persons are exposed as a consequence of their employment provided those persons are fully aware of the potential for exposure and can exercise control over their exposure. Limits for Occupational/Controlled exposure also apply in situations when an individual is transient through a location where Occupational/Controlled limits apply provided he or she is made aware of the potential for exposure." Page 14 of 18 Prepared for: T-Mobile, Site: SE04000B For General Population/Uncontrolled limits, the FCC states that "General Population/ Uncontrolled exposures apply in situations in which the general public may be exposed, or in which persons that are exposed as a consequence of their employment may not fully be aware of the potential for exposure or cannot exercise control over their expos ire." For purposes of this analysis, all limits are evaluated against the Power Density limits. Typical guidelines for determining whether Occupational/Controlled limits can be applied include insuring the environment (such as a rooftop) as limited/controlled access via locked doors or physical barrier that are preferably controlled by a landlord that is aware of the situation and can inform anyone going through the locked door of the existence of the RF emissions. Such notification/awareness is typically accomplished by means of signage on the door, or other access to the area of concern, as well as signage on or near the antennas. Examples of such signs include the following: re.V c • Radio frequency tetds beyond this point may exceed the FCC genera/ public exposure limit. Obey an posted signs and site guidelines fin wetting In radio rntquency environments. CAUTION Beyond this point: Radio frequency fields at this site nay exceed FCC rules for human exposure. Fos your safety, obey ax posted signs and site guidelines for working in radio frequency environments. • Beyond this point Radio frequency fields at this site exceed the FCC rutes for human exposure. Failure lo obey ali posted signs and sae grrid.anes far working In radio frequency environments could result in serious Mrtuty. Standards for when to use each of the above signs for Occupational situations are as follows: No sign required: <20% of Occupational MPE Blue Sign, Notice: 20% to <100% of MPE Yellow Sign, Caution: 100% to <1000% of MPE Red Sign, Warning: >1000% of MPE All MPE references are to the FCC Occupational limits. Page 15 of 18 Prepared for: T-Mobile, Site: SE04000B Appendix B: Overview of RoofView® Functions and Assumptions RoofView® is a tool developed and supported by Richard Tell Associates, Inc. to be used for analysis of RF field levels at telecommunications sites produced by antennas of the type commonly used in cellular, paging, SMR, PCS and two-way radio communications services. Although its name suggests that the tool is only for use in evaluating emissions for roof top applications, it can also be used to evaluate ground level effects of tower facilities. RoofView® allows the user to apply near field, far field, or a combination of near and far field computational methods as desired by the user. For this analysis, near field computations are used for areas within the near field, and far field computations are used beyond the near field. Specific break points are dynamic based on the aperture of the antenna being analyzed. The near field methodology is based on a cylindrical model that assumes the power into an antenna is distributed as a cylinder around the aperture of the antenna. Research by Richard Tell Associates, Inc. found that using such a model, along with corrections for height and antenna pattern, is very accurate, if not slightly conservative in estimating RF exposure. FCC Bulletin 65 recognizes the use of the cylindrical model for near field calculations. The following picture and corresponding equation summarizes the computations used by RoofView® on a bin -by -bin basis when the near field method is used: S= 360P 0 BW 2nRh 3 dB Beam (degrees) - eBW Each bin's results are then also adjusted by spatially averaging the portion of a 6 foot tall human that intercepts the aperture over 6 feet. Once the antenna is completely above (or below) the height that corresponds to a 6 foot tall human, the cylindrical results are Page 16 of 18 Prepared for: T-Mobile, Site: SE04000B reduced to 10% of their results and then dissipated inversely in proportion to the square of the distance. Once bins being analyzed fall outside of the near field (as determined by a method and variable that is user -selectable; see below for method and variable used in this analysis), a far -field spatial average is calculated. Spatially averaged power density in the far -field is calculated by reducing the spatially averaged power density inversely, by the square of the distance from the antenna(s). There are several input variables to RoofView® that can impact the results produced when evaluating specific cell sites. Those variables are summarized accordingly: Required Inputs for RoofView® v4.15 Analysis Thresholds >= 0% >= 5% >= 20% >= 100% 'Blue Yellow (Relative to Controlled Limits) Green < 5% < 20% < 100% Standard FCC 1997 Occupational (default) FCC 1997 General Population (as applicable) Model Near/Far Spatial Average Uptime 100% (vary as applicable) Near/Far Field Transition Method X ApHt Near/Far Field Transition At Ht Factor 1.5 Page 17 of 18 Prepared for: T-Mobile, Site: SE04000B References FCC (1997). "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields"; Federal Communications Commission; Office of Engineering and Technology, OET Bulletin 65, Edition 97-01, August. Richard Tell Associates, Inc. (2003). RoofView® User Guide Version 4.15, Richard Tell Associates, Inc., February 10, 2003. Limited Warranty Centerline Solutions, LLC warrants that this analysis was performed in good faith using the methodologies and assumptions covered in this report and that data used for the analysis and report were obtained by Centerline Solutions, LLC employees or representatives via site surveys or research of T-Mobile's available information. In the event that specific third party details were not available, best efforts were made to use assumptions that are based on industry experience of various carriers' standards without violating any confidential information obtained under non -disclosure terms. Centerline Solutions, LLC also warrants that this analysis was performed in accordance with industry acceptable standards and methods. There are no other warranties, express or implied, including but not limited to, the implied warranties of merchantability and fitness for a particular purpose, relating to this agreement or to the services rendered by Centerline Solutions hereunder. In no event shall Centerline Solutions be held liable to T-Mobile, or to any third party, for any indirect, special, incidental, or consequential damages, including but not limited to loss of profits, loss of data, loss of good will, and increased expenses. In no event shall Centerline Solutions be liable to T-Mobile for damages, whether based in contract, tort, negligence, strict liability, or otherwise, exceeding the amount payable hereunder for the services giving rise to such liability. Page 18 of 18 • / \ ._ � COMPLETE APPLICATION CHECKLIST The materials listed below must be submitted with your application unless specifically waived in writing the Department of Community Development. Please contact each Department if you feel that certain items are not applicable to your project and should be waived. Application review will not begin until it is determined to be complete. ADDITIONAL MATERIALS MAY BE REQUIRED. The initial application materials allow project review to begin and vest the applicant's rights. However, the City may require additional information as needed to establish consistency with development standards. City staff are available to answer questions about application materials at 206-431-3670 (Department of Community Development) and 206-433-0179 (Department of Public Works). Check items submitted with application Information Required. May be waived in unusual cases, upon approval of both Public Works and Planning APPLICATION MATERIALS: Items 1-9 are required for ALL Wireless Telecommunication Facilities. 1 1. Application Checklist (1 copy) indicating items submitted with application. ✓ 2. Completed Application Form and drawings (5 copies). ✓ 3. Four sets of plans prepared by a design professional. The plans shall include a vicinity map, site map, architectural elevations, method of attachment, proposed screening, location of proposed antennas, and all other information which accurately depicts the proposed project. Minimum size is 8 1/2" x 11". Plans shall be no greater than 24" x 36". 1 4. Application Fee: See Land Use Fee Schedule. 1 5. Completed and notarized Affidavit of Ownership and Hold Harmless Permission to Enter Property (1 copy attached). 6. SEPA Environmental Checklist. SEPA is not required when the facility: i) Is a microcell and is to be attached to an existing structure that is not a residence or school and does not contain a residence or a school; ii) Includes personal wireless antennas, other than a microcell, and is to be attached to an existing structure (that may be an existing tower) that is not a residence or school and does not contain a residence or school, and the existing structure to which it is to be attached is located in a commercial, industrial, manufacturing, forest or agriculture zone; or iii) Involves constructing a personal wireless tower less than sixty feet in height that is located in a commercial, industrial, manufacturing, forest, or agricultural zone. 1 7. A letter from the applicant describing the proposed project and describing compliance with the City's Code requirements. 8. Sensitive Area studies and proposed mitigation (if required). 9. If an outdoor generator is proposed, a report prepared by an acoustical engineer demonstrating compliance with TMC Chapter 8.22, "Noise". If the application requires a Type 2 review these additional items are needed: 1 10. Four sets of photo simulations that depict the existing and proposed view of the proposed facility; 11. Materials board for the screening material; 12. Landscaping plan; 1 13. Letter from a radio frequency engineer that demonstrates that the facility meets Federal requirements for allowed emissions; 14. If the facility is located within a residential zone, a report from a radio frequency engineer explaining the need for the proposed wireless communication facility at that location. Additionally, the applicant shall provide detailed discussion on why the wireless communication facility cannot be located within a commercial or industrial zone. \\deptstore\City Common\Teri\Revisions In Progress\Wreless Communication Facility-Jan2011.docx • Check items submitted with application Information Required. May be waived in unusual cases, upon approval of both Public Works and Planning If the application requires a Type 3 review these additional items are needed: 15. A narrative responding to the criteria at TMC Section 18.58.060. 16. The radio frequency engineer report shall include a discussion of the information required under TMC Section 18.58.070. The report shall also explain why a tower must be used instead of any of the other location options outlined in Table A. 17. Engineering Plans for the proposed tower. 18. A vicinity map depicting the proposed extent of the service area. 19. A graphic simulation showing the appearance of the proposed tower and ancillary structures and ancillary facilities from five points within the impacted vicinity. Such points are to be mutually agreed upon by the Director of DCD and applicant. All plans and photo simulations shall include the maximum build -out of the proposed facility. 20. Evidence of compliance with Federal Aviation Administration (FAA) standards for height and lighting and certificates of compliance from all affected agencies. 21. Evidence that the tower has been designed to meet the minimum structural standards for wireless communication facilities for a minimum of three providers of voice, video or data transmission services, including the applicant, and including a description of the number and types of antennas the tower can accommodate. PUBLIC NOTICE MATERIALS: 22. Payment of notice board fee (see Land Use Fee schedule) to FastSigns Tukwila OR provide a 4' x 4' public notice board on site within 14 days of the Department determining that a complete application has been received (see Public Notice Sign Specifications Handout). 23. Pay the fee as established by the Land Use Fee Schedule for generating mailing labels; OR provide an excel spreadsheet of mailing labels for all property owners and tenants (residents and businesses) within 500 feet of the subject property. Each unit in multiple family buildings e.g. apartments, condos, trailer parks --must be included. Once your project is assigned to a planner, you will be required to provide an electronic copy of the mailing label spreadsheet in the following format: Name, Street Address, City St Zip, with each of these fields as an individual column: Name Street Address City, St, Zip Mr. Smith 1234 Park Ave S Tukwila WA 98188 PLEASE NOTE: Regardless of whether you pay the City to generate the mailing labels or you provide them, there is an additional fee for postage and material as listed under Public Notice Mailing Fee on the Land Use Fee Schedule. Payment of this fee is due prior to issuance of the decision and you will receive a separate bill for this fee. 24. If providing own labels, include King County Assessor's map(s) which shows the location of each property within 500 ft. of the subject lot. \\deptstore\City Common\Teri\Revisions In Progress\Wireless Communication Facility-Jan2011.docx r SE04000B South Center Place CITY OF TUKWILA Department of Community Development 6300 Southcenter Boulevard, Tukwila, WA 98188 Telephone: (206) 431-3670 AFFIDAVIT OF OWNERSHIP AND HOLD HARMLESS PERMISSION TO ENTER PROPERTY STATE OF WASHINGTON -Gc.sJ ipty DEC 112015 Community Development ss COUNTY OF KING The undersigned being duly sworn and upon oath states as follows: 1. I am the current owner of the property which is the subject of this application. 2. All statements contained in the applications have been prepared by me or my agents and are true and correct to the best of my knowledge. 3. The application is being submitted with my knowledge and consent. 4. Owner grants the City, its employees, agents, engineers, contractors or other representatives the right to enter upon Owner's real property, located at 16400 Southcenter Parkway Tukwila, WA 98188 for the purpose of application review, for the limited time necessary to complete that purpose. 5. Owner agrees to hold the City harmless for any loss or damage to persons or property occurring on the private property during the City's entry upon the property, unless the loss or damage is the result of the sole negligence of the City. 6. Non -responsiveness to a City information request for ninety (90) or more days, shall be cause to cancel the application(s) without refund of fees. EXECUTED at Itt e vC.c Flo..{ (city), jf/`4- (state), on D rn11,c. 1 C] , 20 15 tc,kcA 5 3 12ccd��ccf (Print Name) (Address) 2$3S 8"2 .1 /Jtv-t 5 2GC, 2Ce (ao(Qo (Phone Number) (Signature) 7//K `-_—� ✓l On this day personally appeared before me i c hc.)1(1`) ,T to me known to be the individual who executed the foregoing instrument and acknowledged that he/she signed the same as his/her voluntary act and deed for the uses and purposes mentioned therein. SUBSCRIBED AND Sl�(t t114IT(ft FORE ME ON THIS [Li DAY OF MCC Of f , 20 4'j 43/65 F-ta\o s NOTARY UB IC in and r the Sta f Washington otc+'ac-) _,', jet — NOTARY' 1 = residing at incip e idle' 1 tvA it zi N .5 PUBLIC, /, 9'•!�E 12 2z°b>" dcptstorelCity Common\Ter \Revtbfb taljjt SWtrelus Communication Facility-1an2011.docx My Commission expires on % 1 a - 301 g' Name: CITY OF TUKWILA Department of Community Development 6300 Southcenter Boulevard, Tukwila, WA 98188 Telephone: (206) 431-3670 fECE VED DEC 112015 Commnity Developument WIRELESS TELE- COMMUNICATION FACILITIES APPLICATION FOR STAFF USE ONLY Permits Plus Type: P-WIRE Planner: File Number: L l_ —/6 ei Application Complete Date: Project File Number: ,pL / ('y 5 f Application Incomplete Date: Other File Numbers: NAME OF PROJECT/DEVELOPMENT: SE04000B South Center Place BRIEF DESCRIPTION OF PROJECT: Modify existing wireless communications facility CIRCLE TYPE - TYPE 1 ■ TYPE 2 TYPE 3 (PUBLIC HEARING NOTICE RQD) LOCATION OF PROJECT/DEVELOPMENT: Give street address or, if vacant, indicate lot(s), block and subdivision, access street, and nearest intersection. 16400 South Center Pliacearkway Tukwila, WA 98108 LIST ALL TAX LOT NUMBERS (this information may be found on your tax statement). 2623049021 DEVELOPMENT COORDINATOR : The individual who: • has decision making authority on behalf of the owner/applicant in meetings with City staff, • has full responsibility for identifying and satisfying all relevant and sometimes overlapping development standards, and • is the primary contact with the City, to whom all notices and reports will be sent. Colin Robinson Tom, T_ ,41. e Address: 8210 154th Ave NE Redmond, WA 98052 Phone: (425) 533-2665 FAX: E-mail: Robinson@centerlinesolutions.com Signature: 17ry --- Date: 12 - 1, - 20, S \\deptstore\City Common\Teri\Revisions In Progress\Wireless Communication Facility-Jan201 l.docx • APPROX. PHOTO LOCATION %. APPROX. PROPOSED ANTENNA LOCATIONS 5 iii ig j r� n(,T�;is Existing �C EN TER LINE CE vE DEC 112015 Community Development obi le SOUTH CENTER PLACE Looking South (N) T-MOBILE PANEL ANTENNAS. TYP OF (1) PER SECTOR, TOTAL OF (3), MOUNTED ON (E) WALL PIPE MOUNTS -SEE NOTES Proposed 4/S..00 NOTES: 1. PM/GC TO VERIFY PAINTING REQUIREMENTS WITH JURISDICTION PRIOR TO ORDERING SUPPORT STRUCTURES, ATTACHMENTS, ANTENNAS, AND OTHER APPURTENANCES. 2. VISUAL IMPACTS WILL BE AFFECTED BY LOCATION AND VISIBILITY OF OBSERVER. THIS DOCUMENT IS FOR PLANNING AND INFORMATION PURPOSES ONLY AND IS CONCEPTUAL. THIS IS SOLELY THE PHOTOGRAPHER'S INTERPRETATION OF THE PROPOSED DEVELOPMENT. 1 ,ce !► APP. W PI�° ®, El ® \ bile CO LOCATICDEC 112015 0PROP. EROXsEoelmomntS O U T H CENTER PLACE o ANTENNA LOCATIONS W Existing Looking East (N) T-MOBILE PANEL ANTENNAS, TYP OF (1) PER SECTOR, TOTAL OF (3), MOUNTED ON (E) WALL PIPE MOUNTS NOT VISIBLE FROM THIS LOCATION -SEE NOTES 2 Proposed / /5.00.00641 NOTES: 1. PM/GC TO VERIFY PAINTING REQUIREMENTS WITH JURISDICTION PRIOR TO ORDERING SUPPORT STRUCTURES, . ATTACHMENTS, ANTENNAS, AND OTHER APPURTENANCES. CENTERLINE 2. VISUAL IMPACTS WILL BE AFFECTED BY LOCATION AND VISIBILITY OF OBSERVER. THIS DOCUMENT IS FOR PLANNING AND INFORMATION PURPOSES ONLY AND IS CONCEPTUAL. THIS IS SOLELY THE PHOTOGRAPHER'S INTERPRETATION OF THE PROPOSED DEVELOPMENT. Existing • APPROX. PHOTO LOCATION APPROX. PROPOSED ANTENNA LOCATIONS "03 DEC 112015 Community Development EN TER LINi T• obile SOUTH CENTER PLACE Looking Northeast (N) T-MOBILE PANEL ANTENNAS, TYP OF (1) PER SECTOR, TOTAL OF (3), MOUNTED ON (E) WALL PIPE MOUNTS NOT VISIBLE FROM THIS LOCATION •SEE NOTES 3 Proposed ( /se. CQ S'9 NOTES: 1. PM/GC TO VERIFY PAINTING REQUIREMENTS WITH JURISDICTION PRIOR TO ORDERING SUPPORT STRUCTURES, ATTACHMENTS, ANTENNAS, AND OTHER APPURTENANCES. 2. VISUAL IMPACTS WILL BE AFFECTED 8Y LOCATION AND VISIBILITY OF OBSERVER. THIS DOCUMENT 1S FOR PLANNING AND INFORMATION PURPOSES ONLY AND IS CONCEPTUAL. THIS IS SOLELY THE PHOTOGRAPHER'S INTERPRETATION OF THE PROPOSED DEVELOPMENT. Existing . i 1 i L APPROX. DEC 111015 •PHOTO Community/ LOCATION Developrnent *. APPROX. PROPOSED ANTENNA LOCATIONS I-r L_ 1 : i l L i I� CENTERLINE T la 13 obile e� SOUTH CENTER PLACE Looking Southwest (N) T-MOBILE PANEL ANTENNAS, TYP OF (1) PER SECTOR, TOTAL OF (3), MOUNTED ON (E) WALL PIPE MOUNTS NOT VISIBLE FROM THIS LOCATION -SEE NOTES • Proposed tJ5»tZ7 ? 4 NOTES: 1. PM/GC TO VERIFY PAINTING REQUIREMENTS WITH JURISDICTION PRIOR TO ORDERING SUPPORT STRUCTURES, ATTACHMENTS, ANTENNAS, AND OTHER APPURTENANCES. 2. VISUAL IMPACTS WILL BE AFFECTED BY LOCATION AND VISIBILITY OF OBSERVER. THIS DOCUMENT IS FOR PLANNING AND INFORMATION PURPOSES ONLY AND IS CONCEPTUAL. THIS IS SOLELY THE PHOTOGRAPHER'S INTERPRETATION OF THE PROPOSED DEVELOPMENT. Tr UQ SOUTH CENTER PLACE 16400 SOUTHCENTER PARKWAY TUKWILA, WA 98188 SITE ID: SE04000B CONSTRUCTION DRAWINGS PROJECT SUMMARY THIS PROJECT INCLUDES THE FOLLOWING SCOPE OF WORK PROPOSED MODIFICATION OF AN EXISTING UNMANNED TELECOMMUNICATIONS FACILITY. MODIFICATIONS TO ROOFTOP EQUIPMENT INCLUDE"': " REMOVAL OF (2) EXISTING PANEL ANTENNAS (TMBXX-6516-R2M, GAMMA SECTOR ONLY) " ADDITION OF (1) NEW PANEL ANTENNAS (DBXNH-6565E-A2M, GAMMA SECTOR ONLY) • ADDITION OF (2) NEW PANEL ANTENNAS (HBXX-3319DS-A2M, GAMMA SECTOR ONLY) • ADDITION OF (1) FRIG AND (1) FXFC (GAMMA SECTOR ONLY) • ADDITION OF (6) DIPLEXERS (ECC1920-VPUB, GAMMA SECTOR ONLY) • ADDITION OF (2) FSMF, (2) FBBC, & (1) ESMB IN (E) CABINET ALL OTHER EXISTING EQUIPMENT TO REMAIN, SEE FJNAL EQUIPMENT EIVENTORY TABLE ON A4.0 FOR COMPLETE SPECIFICATIONS. PROJECT VICINITY & AERIAL MAPS SITE INFORMATION SITE NAME: SITE ID: SITE ADDRESS: LATITUDE: LONGITUDE: SOURCE: PARCEL NUMBER: ZONING CLASSIFICATION: JURISDICTION: TOP OF (E) PENTHOUSE: OCCUPANCY GROUP: CONSTRUCTION TYPE: SOUTHCENTER PLACE SE04000B 16400 SOUTHCENTER PARKWAY TUKWILA, WA 98188 47°27'19.0" N (47.455278) 122°15'42.0" W (122.261667) 1A 2623049021 TUC CITY OF TUKWILA 73.0' AGL U I I-B DRIVING DIRECTIONS FROM T-MOBILE BOTHELL OFFICE 1. TAKE RAMP LEFT FOR 1-405 SOUTH TOWARD RENTON (24.2 MI) 2. TAKE RAMP RIGHT FOR 1-5 NORTH TOWARD SOUTHCENTER BLVD & MALL (0.3 MI) 3. TURN RIGHT ONTO SOUTHCENTER BLVD (0.3 MI) 4. TURN RIGHT ONTO 61ST AVE S (0.1 MI) 5. TURN RIGHT ONTO SOUTHCENTER PKWY (0.6 MI) 6. ARRIVE AT 16400 SOUTHCENTER PKWY, TUKWILA, WA 98188 ESTIMATED DISTANCE: ESTIMATED TIME: 26.0 MILES 30 MINUTES 6.05° GOVERNING CODES IBC-2012, INTERNATIONAL BUILDING CODE W/ LOCAL AMENDMENTS NEC-2008, NATIONAL ELECTRICAL CODE A.D.A. COMPLIANCE INSTALLATION IS UNMANNED AND NOT FOR HUMAN HABITATION. HANDICAP ACCESS IS NOT REQUIRED PER A.DA. PROJECT CONTACTS DRAWING INDEX APPLICANT T-MOBILE 19807 NORTH CREEK PKWY N BOTHELL, WA 98011 PROPERTY OWNER LEGACY PARTNERS COMMERCIAL 4000 E THIRD AVE, SUITE 600 FOSTER CITY, CA 94404 PROJECT CONSULTANT CENTERLINE SOLUTIONS 8218 154TH AVE NE REDMOND, WA 98052 RICK STOCKMANN PH: 425.890.1437 SITE ACQUISITION CONSULTANT CENTERLINE SOLUTIONS 8218 154TH AVE NE REDMOND, WA 98052 RICK STOCKMANN PH: 425.890.1437 ZONING & PERMITTING CONSULTANT CENTERLINE SOLUTIONS 8218 154TH AVE NE REDMOND, WA 98052 RICK STOCKMANN PH: 425.890.1437 CONSTRUCTION MANAGER CENTERLINE SOLUTIONS 8218 154TH AVE NE REDMOND, WA 98052 RICK YOUNG PH: 425.954.8613 RF ENGINEER T-MOBILE 19807 NORTH CREEK PKWY N BOTHELL, WA 98011 GLENN DIME STRUCTURAL ENGINEER VECTOR STRUCTURAL ENGINEERS 9138 S STATE STREET, SUITE 101 SANDY, UT 84070 ROGER T. ALWORTH, S.E. PH: 801.990.1775 RECEIVED DEC 112015 Community Development SHEET T1.0 GN1.0 A1.0 A1.1 A2.0 A3.0 A4.0 A5.0 A6.0 RF1.0 DESCRIPTION TITLE SHEET GENERAL NOTES OVERALL SITE PLAN ENLARGED ROOF PLAN ENLARGED EQUIPMENT PLAN ELEVATIONS ANTENNA DETAILS & PLANS ANTENNA & EQUIPMENT DETAILS CONSTRUCTION DETAILS RF DETAILS Know what's below. CaII before you dig. THE INFORMATION CONTAINED IN THIS SET OF DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO T-MOBILE SERVICES IS STRICTLY PROHIBITED. SIGN OFF OF FINAL CONSTRUCTION DRAWINGS REVIEWERS SHALL CLEARLY PLACE INITIALS ADJACENT TO EACH REDLINE NOTE AS DRAWINGS ARE BEING REVIEWED CONSULTANT SIGNATURE DATE SITE ACQUISITION PERMITTING CONSULTANT RF ENGINEER: CONST. MNGR. OPS MNGR. PROJECT MNGR. REGULATORY REV. DEV. MNGR. T. It obi1e- ,i( CENTERLINE WLdeaAMraAs v • Il • I Il ■ • R • af+ z4� iU d 11/12/15 EXP. 1/27/16 CPM PROJECT NO.: 8856 PRELIMINARY NO. DATE D/C DESCRIPTION 0 10-22-15 MS/MS 90% CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT SUBMITTAL NO. DATE D/C DESCRIPTION 1 11-11-15 MS/MS BP SUBMITTAL SITE NAME: SOUTHCENTER PLACE SITE ID: SE04000B SITE ADDRESS: 16400 SOUTHCENTER PARKWAY TUKWILA, WA 98188 SHEET TIRE TITLE SHEET SHEET NO. T1.0 4/5---vosasT GENERAL NOTES 1. THE FACILITY IS AN UNOCCUPIED SPECIALIZED MOBILE RADIO FACILITY. 2. PLANS ARE NOT TO BE SCALED AND ARE INTENDED TO BE A GRAPHIC REPRESENTATION OF THE FINAL INSTALLATION. THE WORK SHALL INCLUDE FURNISHING MATERIALS, EQUIPMENT, APPURTENANCES AND LABOR NECESSARY TO COMPLETE ALL INSTALLATIONS AS INDICATED ON THE DRAWINGS. 3. PRIOR TO THE SUBMISSION OF BIDS, THE CONTRACTOR SHALL VISIT THE JOB SITE AND BE RESPONSIBLE FOR ALL CONTRACT DOCUMENTS, FIELD CONDITIONS, AND DIMENSIONS AND CONFIRMING THAT THE WORK MAY BE ACCOMPLISHED AS SHOWN PRIOR TO PROCEEDING WITH CONSTRUCTION. ANY DISCREPANCIES ARE TO BE BROUGHT TO THE ATTENTION OF THE PROJECT MANAGER. 4. THE CONTRACTOR SHALL RECEIVE, IN WRITING, AUTHORIZATION TO PROCEED BEFORE STARTING WORK. 5. THE CONTRACTOR SHALL INSTALL ALL EQUIPMENT AND MATERIALS IN ACCORDANCE WITH MANUFACTURERS RECOMMENDATIONS UNLESS SPECIFICALLY OTHERWISE INDICATED OR WHERE LOCAL CODES OR REGULATIONS TAKE PRECEDENCE. 6. ALL WORK PERFORMED AND MATERIALS INSTALLED SHALL BE IN STRICT ACCORDANCE WITH APPLICABLE CODES, REGULATIONS, AND ORDINANCES. CONTRACTOR SHALL GIVE ALL NOTICES AND COMPLY WITH ALL LAWS, ORDINANCES, RULES, REGULATIONS, AND LAWFUL ORDERS OF ANY PUBLIC AUTHORITY BEARING ON THE PERFORMANCE OF THE WORK. MECHANICAL AND ELECTRICAL SYSTEMS SHALL BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE MUNICIPAL AND UTILITY COMPANY SPECIFICATIONS AND LOCAL AND STATE JURISDICTIONAL CODES, ORDINANCES, AND APPLICABLE REGULATIONS. 7. THE CONTRACTOR SHALL SUPERVISE AND DIRECT THE WORK USING BEST SKILLS AND ATTENTION. THE CONTRACTOR SHALL BE SOLELY RESPONSIBLE FOR ALL CONSTRUCTION MEANS, METHODS, TECHNIQUES, SEQUENCES, AND PROCEDURES AND FOR COORDINATING ALL PORTIONS OF THE WORK UNDER THE CONTRACT INCLUDING CONTACT AND COORDINATION WITH THE PROJECT MANAGER AND WITH LANDLORD'S AUTHORIZED REPRESENTATIVE. 8. PROVIDE A PORTABLE FIRE EXTINGUISHER WITH A RATING OF NOT LESS THAN 2-A OR 2-A10BC WITHIN 5 FEET OF TRAVEL DISTANCE TO ALL PORTIONS OF THE PROJECT AREA DURING CONSTRUCTION. 9. THE CONTRACTOR SHALL PROVIDE SITE FOREMAN WITH A CELLULAR PHONE, AND KEEP SAME ON SITE WHENEVER ANY PERSONNEL ARE ON SITE. 10. DETAILS ARE INTENDED TO SHOW END RESULT OF DESIGN. MINOR MODIFICATIONS MAY BE REQUIRED TO SUIT JOB DIMENSIONS OR CONDITIONS, AND SUCH MODIFICATIONS SHALL BE INCLUDED AS PART OF THE WORK. 11. THE CONTRACTOR SHALL MAKE NECESSARY PROVISIONS TO PROTECT EXISTING IMPROVEMENTS, PAVING, CURBS, GALVANIZED SURFACES, ETC., AND UPON COMPLETION OF WORK, REPAIR ANY DAMAGE THAT OCCURRED DURING CONSTRUCTION TO THE SATISFACTION OF THE PROJECT MANAGER AND/OR LANDLORD. 12. ON A DAILY BASIS: KEEP GENERAL AREA CLEAN, HAZARD FREE, AND DISPOSE OF ALL DIRT, DEBRIS, RUBBISH, AND REMOVE EQUIPMENT NOT SPECIFIED AS REMAINING ON THE PROPERTY. LEAVE PREMISES IN CLEAN CONDITION AND FREE FROM PAINT SPOTS, DUST OR SMUDGES OF ANY NATURE. 13. CONTRACTOR TO PROVIDE COMPLETE SET OF AS -BUILT DRAWINGS WITHIN 10 WORKING DAYS OF PROJECT COMPLETION. 14 WHERE A CONSTRUCTION DETAIL IS NOT SHOWN OR NOTED, THE DETAIL SHALL BE THE SAME AS FOR OTHER SIMILAR WORK. 15. ASTM SPECIFICATIONS NOTED ON THE DRAWINGS SHALL BE OF THE LATEST REVISION. 16 IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO LOCATE ALL EXISTING UTILITIES WHETHER SHOWN HEREON OR NOT AND TO PROTECT THEM FROM DAMAGE. THE CONTRACTOR SHALL BEAR ALL EXPENSE OF REPAIR OR REPLACEMENT IN CONJUNCTION WITH THE EXECUTION OF THIS WORK. 17. ALL ITEMS REMOVED OR DAMAGED DURING CONSTRUCTION WORK WILL BE REPLACED OR REPAIRED TO MATCH EXISTING. 18. ALL ELEMENTS OF EXISITNG STRUCTURE TO REMAIN INDISTURBED, UNO. EXISTING STRUCTURE IS ASSUMED TO BE IN GOOD CONDITION, FREE OF DAMAGE OR DETEREORATION. CONTRACTOR TO VERIFY ALL ELEMENTS OF EXISTING STRUCTURE AFFECTED BY THIS MODIFICATION AND NOTIFY FOR IF ANY DAMAGE, DETEREORATION, OR DISCREPANCIES BETWEEN THE EXISTING CONDITIONS AND THOSE DEPICTED ON THESE CONSTRUCTION DRAWINGS ARE FOUND. SPECIAL INSPECTION 1. IF REQUIRED, SPECIAL INSPECTIONS SHALL BE PERFORMED BY AN INDEPENDENT SPECIAL INSPECTOR. 2. THE SPECIAL INSPECTOR SHALL PROVIDE A COPY OF THEIR REPORT TO THE OWNER, ARCHITECT, STRUCTURAL ENGINEER, CONTRACTOR, AND BUILDING OFFICIAL AS EACH TEST IS COMPLETED. 3. ANY MATERIAL WHICH FAILS TO MEET THE PROJECT SPECIFICATIONS SHALL IMMEDIATELY BE BROUGHT TO THE ATTENTION OF THE ARCHITECT AND THE STRUCTURAL ENGINEER. SPECIAL INSPECTION TESTING REQUIREMENTS APPLY EQUALLY TO ALL BIDDER DESIGNED COMPONENTS. 4. INSPECTION FOR PREFABRICATED CONSTRUCTION SHALL BE THE SAME AS FOR THE MATERIAL USED IF THE CONSTRUCTION TOOK PLACE ON SITE. CONTINUOUS INSPECTION WILL NOT BE REQUIRED DURING PREFABRICATION IF THE APPROVED AGENCY CERTIFIES THE CONSTRUCTION AND FURNISHES EVIDENCE OF COMPLIANCE. 5. THE SPECIAL INSPECTOR SHALL SUBMIT A FINAL REPORT CERTIFYING THAT ALL WORK REQUIRING SPECIAL INSPECTION WAS, TO THE BEST OF THE SPECIAL INSPECTOR'S KNOWLEDGE IN CONFORMANCE WITH THE APPROVED PERMIT PLANS AND SPECIFICATIONS AND THE APPLICABLE WORKMANSHIP PROVISIONS. STRUCTURAL NOTES GENERAL STRUCTURAL NOTES: 1. WHERE A CONSTRUCTION DETAIL IS NOT SHOWN OR NOTED, THE DETAIL SHALL BE THE SAME AS FOR OTHER SIMILAR WORK. 2. NOTES AND DETAILS ON DRAWINGS SHALL TAKE PRECEDENCE OVER GENERAL NOTES. 3. NO PIPES, DUCTS, SLEEVES, CHASES, ETC., SHALL BE PLACED IN SLABS, BEAMS, OR WALLS UNLESS SPECIFICALLY SHOWN OR NOTED, NOR SHALL ANY STRUCTURAL MEMBER BE CUT FOR PIPES, DUCTS, ETC., UNLESS OTHERWISE NOTED. CONTRACTOR SHALL OBTAIN PRIOR APPROVAL FOR INSTALLATION OF ANY ADDITIONAL PIPES, DUCTS, ETC. 4. CONTRACTOR AGREES THAT HE SHALL ASSUME SOLE AND COMPLETE RESPONSIBILITY FOR JOB SITE CONDITIONS DURING THE COURSE OF CONSTRUCTION OF THIS PROJECT INCLUDING SAFETY OF ALL PERSONS AND PROPERTY; THAT THIS REQUIREMENT SHALL APPLY CONTINUOUSLY AND NOT BE LIMITED TO NORMAL WORKING HOURS; AND THAT THE CONTRACTOR SHALL DEFEND, INDEMNIFY AND HOLD T-MOBILE AND THE ARCHITECT/ENGINEER HARMLESS FROM ANY AND ALL LIABILITY, REAL OR ALLEGED, IN CONNECTION WITH THE PERFORMANCE OF WORK ON THIS PROJECT, EXCEPTING FOR LIABILITY ARISING FROM THE SOLE NEGLIGENCE OF T-MOBILE OR THE ARCHITECT/ENGINEER. 5. THE CONTRACT DRAWINGS AND SPECIFICATIONS REPRESENT THE FINISHED STRUCTURE. THEY DO NOT INDICATE THE METHOD OF CONSTRUCTION. THE CONTRACTOR SHALL PROVIDE ALL MEASURES NECESSARY TO PROTECT THE STRUCTURE, WORKERS, AND PEDESTRIANS DURING CONSTRUCTION. SUCH MEASURES SHALL INCLUDE, BUT NOT BE LIMITED TO BRACING, SHORING FOR LOADS DUE TO CONSTRUCTION EQUIPMENT, TEMPORARY STRUCTURES, AND PARTIALLY COMPLETED WQRK, ETC. OBSERVATION VISITS TO THE SITE BY THE ARCHITECT/ENGINEER SHALL NOT INCLUDE INSPECTION OF SUCH ITEMS. 6. ASTM SPECIFICATIONS NOTED ON THE DRAWINGS SHALL BE OF THE LATEST REVISION. 7. CONSTRUCTION MATERIALS SHALL BE SPREAD OUT IF PLACED ON FRAMED FLOOR OR ROOF. LOAD SHALL NOT EXCEED THE DESIGN LIVE LOAD PER SQUARE FOOT. PROVIDE ADEQUATE SHORING/BRACING WHERE STRUCTURE HAS NOT ATTAINED DESIGN STRENGTH. 8. IT SHALL BE THE RESPONSIBILITY OF THE CONTRACTOR TO LOCATE ALL EXISTING UTILITIES WHETHER SHOWN HEREON OR NOT AND TO PROTECT THEM FROM DAMAGE. THE CONTRACTOR SHALL BEAR ALL EXPENSE OF REPAIR OR REPLACEMENT IN CONJUNCTION WITH THE PROSECUTION OF THIS WORK. 9. DIMENSIONS SHALL TAKE PRECEDENCE OVER SCALES SHOWN ON DRAWINGS. 10. THESE NOTES SHALL BE CONSIDERED A PART OF THE WRITTEN SPECIFICATIONS. 11. ALL ITEMS REMOVED DURING CONSTRUCTION WORK (I.E., DRYWALL, PLYWOOD, CEILING PANELS, ETC.) SHALL BE REPLACED TO MATCH EXISTING. THE FOLLOWING REQUIREMENTS SHALL BE MET FOR SPECIAL INSPECTION: A. THE SPECIAL INSPECTOR SHALL BE UNDER THE SUPERVISION OF A REGISTERED PROFESSIONAL ENGINEER. B. THE SPECIAL INSPECTOR SHALL FURNISH INSPECTION REPORTS TO THE ARCHITECT/ENGINEER, AND OTHER DESIGNATED PERSONS. ALL DISCREPANCIES SHALL BE BROUGHT TO THE IMMEDIATE ATTENTION OF THE CONTRACTOR FOR CORRECTION; THEN, IF UNCORRECTED, TO THE PROPER DESIGN AUTHORITY AND THE BUILDING OFFICIAL. C. THE SPECIAL INSPECTOR SHALL SUBMIT A FINAL REPORT SIGNED BY BOTH HE AND HIS SUPERVISOR STATING WHETHER THE WORK REQUIRING SPECIAL INSPECTION WAS IN CONFORMANCE WITH THE APPROVED PLANS AND SPECIFICATIONS AND THE APPLICABLE WORKMANSHIP PROVISIONS OF THE CODE. D. COMPLY WITH ALL CITY SPECIAL INSPECTION REQUIREMENTS. STANDARD STRUCTURAL STEEL NOTES: 1. ALL METAL WORK SHALL BE IN ACCORDANCE WITH THE SPECIFICATION GALVANIZED ASTM A123-A123M-02 UNLESS NOTED OTHERWISE. 2. STRUCTURAL TUBING MEMBERS SHALL CONFORM TO ASTM A500, GRADE A OR A501. 3. ALL WELDING SHALL BE DONE USING E70XX ELECTRODES AND WELDING SHALL CONFORM TO AISC AND AWS D1.1 WHERE FILLET WELD SIZES ARE NOT SHOWN, PROVIDE THE MINIMUM SIZE PER TABLE J2.4 IN THE AISC "MANUAL OF STEEL CONSTRUCTION", 14TH EDITION. 4. BOLTED CONNECTIONS SHALL USE BEARING TYPE GALV. ASTM A307 BOLTS (5/8" DIA. UNO) AND SHALL HAVE A MINIMUM OF TWO BOLTS U.N.O AND SHALL INCLUDE HEAVY -HEX NUTS AND STANDARD CUT WASHERS. @@��qq IImo�TSfi.. 5. NON-STRUCTURAL CONNECTIONS FOR HANDRAIL, LADDERS AI�[iSLIVYIR'' DIA GALVANIZED ASTM A307 BOLTS U.N.O. dd LanISM. 6. ALL STRUCTURAL PIPE ASTM A53, TYPE E OR S, GRADE B. DEC 112015 SPECIAL INSPECTION: 1. IF REQUIRED, SPECIAL INSPECTIONS SHALL BE PERFORMED BY AN ►pIUEPI�I$I itOtCIAL INSPECTOR PER CODE FOR THE FOLLOWING ITEMS: 1 eVe Opfleflt A. CONTINUOUS DURING THE INSTALLATION OF EXPANSION AND/OR ADHESIVE ANCHORS: INSPECT HOLE SIZE, DEPTH, CLEANLINESS, AND INSTALLATION PER ICC REPORT. B. PERIODIC FOR HIGH STRENGTH BOLT INSTALLATIONS (A325). DRAWING ABBREVIATIONS AFF ABOVE FINISH FLOOR LF LINEAR FEET AGL ABOVE GRADE LEVEL MAX MAXIMUM AWG AMERICAN WIRE GAUGE MECH MECHANICAL AC AIR CONDITIONING MFR MANUFACTURER ADJ ADJUSTABLE MGR MANAGER APPROX APPROXIMATELY MIN MINIMUM AZ AZIMUTH MISC MISCELLANEOUS BLDG BUILDING MTL METAL CM CONSTRUCTION MANAGER MTZL METALIZE(D) CAB CABINET MW MICROWAVE CL CENTERLINE NEC NATIONAL ELECTRICAL CODE CLG CEILING NIC NOT IN CONTRACT CLR CLEAR NTS NOT TO SCALE CO COPPER N/A NOT APPLICABLE CONC CONCRETE OC ON CENTER COND CONDUIT OD OUTSIDE DIAMETER CONST CONSTRUCTION OP OVERHEAD POWER CONT CONTINUOUS OT OVERHEAD FIBER CPM CASCADIA PM OPP OPPOSITE D/C DRAFTER/CHECKER PL PROPERTY LINE DEMO DEMOLISH PLYWD PLYWOOD DIA DIAMETER PM PROJECT MANAGER DIM DIMENSION PROJ PROJECT DN DOWN PROP PROPERTY DTL DETAIL PT PRESSURE TREATED DWG DRAWING RO ROUGH OPENING EA EACH ROW RIGHT OF WAY ELECT ELECTRICAL RRU REMOTE RADIO UNIT ELEV ELEVATION REQ REQUIRED EQ EQUAL SBTC SOLID BARE TINNED COPPER EQUIP EQUIPMENT SF SQUARE FEET EXT EXTERIOR SHT SHEET FIN FINISH SPEC SPECIFICATION FLR FLOOR SO SQUARE FT FOOT, FEET SS STAINLESS STEEL GA GAUGE STL STEEL GALV GALVANIZED STRUCT STRUCTURE, STRUCTURAL GC GENERAL CONTRACTOR TOC TOP OF CONCRETE GWB GYPSUM WALL BOARD TOM TOP OF MASONRY GR GRADE THRU THROUGH GRND GROUND TNND TINNED HVAC HEATING, VENTING 8 AIR CONDITIONING UBC UNIFORM BUILDING CODE HORIZ 'HORIZONTAL UG UNDERGROUND HT HEIGHT UNO UNLESS NOTED OTHERWISE IBC INTERNATIONAL BUILDING CODE UP UNDERGROUND POWER ID INSIDE DIAMETER OF UNDERGROUND FIBER IN INCH VIF VERIFY IN FIELD INSUL INSULATION VERT VERTICAL INT INTERIOR WP WATERPROOF JBOX JUNCTION BOX W/ WITH LB(S) POUND(S) W/O WITHOUT m •Mobile - 4 CENTERLINE AdhdigWLdatNew rb / ■ 11 • 1 rl ■ ■ R • CPM PROJECT NO.: 8856 PRELIMINARY NO. DATE D/C DESCRIPTION 0 10-22-15 MS/MS 90% CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT BUBMTTAL NO. DATE D/C DESCRIPTION 1 11-11-15 MS/MS BP SUBMITTAL SITE NAME: SOUTHCENTER PLACE SITE ID: S E04000 B SITE ADDRESS: 16400 SOUTHCENTER PARKWAY TUKWILA, WA 98188 SHEET TITLE GENERAL NOTES SHEET NO. GN1.0 ,g.c10s9 1 J T-MOBILE PROJECT AREA BUILDING (TYP) SEE SHEET A4.0 STRANDER BLVD I PARCEL #: 2623049021 r T-MOBILE PROJECT AREA SEE SHEET A2.0 INGRESS/EGRESS FROM STRANDER BLVD (E) ADJACENT PROPERTY LINE (TYP) (E) SUBJECT PROPERTY LINE (TYP) DRAWING LEGEND - - - SUBJECT PROPERTY LINE - - ADJACENT PROPERTY LINE COAX COAX ROUTE HYBRID HYBRID CABLE ROUTE EXISTING FENCE ® ELEVATION MARKER ArkDETAIL REFERENCE ® SECTION MARKER COMMON ABBREVIATIONS (E) EXISTING (N) NEW ABBREVIATIONS CONTINUED (TYP) TYPICAL ONSHEETGN1.0 NOTE: SITE PLAN DERIVED FROM; EXISTING DRAWINGS, GIS, AERIAL IMAGES AND SITE PHOTOS. /56--e05.9 RECEVE DEC 112015 Community Development S 1 OVERALL SITE PLAN SCALE: 1" = 40'-0" (11 X17) SCALE: 1" = 20'-0" (22X34) 0' 20' 40' 80' T • -Mobile >CENTERLINE Aahhdig NLelars'Woods e/\ / ■ A • 1 A ■ ■ R • CPM PROJECT NO.: 8856 PRELJMINARY NO. DATE D/C DESCRIPTION 0 10-22-15 MS/MS 90% CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT SUBMITTAL NO. DATE D/C DESCRIPTION _ 1 11-11-15 MS/MS BP SUBMITTAL SITE NAME: SOUTHCENTER PLACE SITE ID: SE04000B SITE ADDRESS: 16400 SOUTHCENTER PARKWAY TU KW ILA, WA 98188 SHEET TITLE ENLARGED ROOF PLAN SHEET NO. A1.1 (E) T-MOBILE ANTENNAS, TYP OF (2) IN GAMMA SECTOR ONLY, TO BE REMOVED (E) T-MOBILE DIPLEXER (TYP OF 2 PER SECTOR, 6 TOTAL) TO REMAIN (E) PENTHOUSE BETA SECTOR GAMMA SECTOR r • (E) T-MOBILE FXFB (RRU) (TYP OF 1 PER SECTOR, 3 TOTAL) TO REMAIN (E) T-MOBILE TMA (TYP OF 2 PER SECTOR, 6 TOTAL) TO REMAIN (E) ROOFTOP VENT, TYP. (E) T-MOBILE FRLB MOUNTED BEHIND ANTENNA ON (E) PIPE MOUNT (TYP OF 1 PER SECTOR, 3 TOTAL) ALPHA SECTOR DEC 112015 Community Development (E) T-MOBILE ROOFTOP MOUNTED EQUIPMENT BELOW (E) T-MOBILE FRIG (RRU) (TYP OF 1 PER SECTOR, 3 TOTAL) TO BE RELOCATED (E) PENTHOUSE VENT, TYP. (E) T-MOBILE COVP (TYP OF 1 PER SECTOR, 3 TOTAL) TO REMAIN (E) T-MOBILE PANEL ANTENNAS, TYP OF (4) TO REMAIN w 16.05° S DRAWING LEGEND - - - - - SUBJECT PROPERTY LINE - - ADJACENT PROPERTY LINE COAX COAX ROUTE HYBRID HYBRID CABLE ROUTE - EXISTING FENCE ArkELEVATION MARKER ink DETAIL REFERENCE ® SECTION MARKER COMMON ABBREVIATIONS (E) EXISTING (N) NEW ABBREVIATIONS CONTINUED (TYP) TYPICAL ON SHEET GN1.0 (N) T-MOBILE PANEL ANTENNAS (TYP OF 2) MOUNTED ON (E) WALL PIPE MOUNTS; SUITABILITY OF MOUNT FOR FINAL LOADING CONFIGURATION TO BE VERIFIED BY OTHERS PRIOR TO INSTALLATION (N) T-MOBILE DIPLEXERS, TYP OF (3), (6 TOTAL), TO BE MOUNTED BEHIND (N) HBXX MODEL ANTENNAS (N) T-MOBILE FXFC, MOUNTED ON (E) PLATFORM W/ (E) FXFB UNIT BETA SECTOR 50 etc? 4, .'‘P 44•&,. GAMMA SECTOR i (N) T-MOBILE PANEL ANTENNAS (TYP OF 1) MOUNTED ON (N) WALL PIPE MOUNT, SEE 1/A6.0 (N) T-MOBILE FRIG (RRU) MOUNTED BEHIND (N) ANTENNA ON (N) PIPE MOUNT BELOW (E) FRIG 4. (E) T-MOBILE FXFB (RRU) (TYP OF 1 PER SECTOR, 3 TOTAL) TO REMAIN • (E) T-MOBILE TMA (TYP OF 2 PER SECTOR, 6 TOTAL) TO REMAIN • ♦ L (N) T-MOBILE DIPLEXERS, TYP OF (3), (6 TOTAL), TO BE MOUNTED BEHIND (N) HBXX MODEL ANTENNAS (E) T-MOBILE COVP (TYP OF 1 PER SECTOR, 3 TOTAL) TO REMAIN (E) T-MOBILE PANEL ANTENNAS, TYP OF (4) TO REMAIN ALPHA SECTOR (E) PENTHOUSE; CAPACITY TO SUPPORT THE PROPOSED LOADING CONFIGURATION TO BE ANALYZED BY OTHERS LfS OO59 (E) T-MOBILE FRLB MOUNTED BEHIND ANTENNA ON (E) PIPE MOUNT (TYP OF 1 PER SECTOR, 3 TOTAL) w 6.05° S 1 ENLARGED ROOF PLAN - EXISTING SCALE: 1/8" = 1'-0" (11X17) SCALE: 1/4" = 1'-0" (22X34) 0' 4' 8' 16' 111 1 ENLARGED ROOF PLAN - FINAL SCALE: 1/8" = 1'-0" (11X17) SCALE: 1/4" = 1-0" (22X34) 0' 4' 8' 16' i i T • •Mobile- 0'CENTERL1NE Mincing WLdnsNaleals ■ A • I A ■ ■ R • CPM PROJECT NO.: 8856 PRELIMINARY NO. DATE D/C 0 10-22-15 MS/MS DESCRIPTION 90% CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT SUBMITTAL NO. 1 DATE 11-11-15 D/C MS/MS DESCRIPTION BP SUBMITTAL SITE NAME: SOUTHCENTER PLACE SITE ID: SE04000B SITE ADDRESS: 16400 SOUTHCENTER PARKWAY TUKWILA, WA98188 SHEET TITLE OVERALL SITE PLAN SHEET NO. Al .0 ROUTE OF (12) (E) T-MOBILE (7/8") COAX (E) T-MOBILE ANTENNAS & ANCILLARY EQUIPMENT; SEE SHEET A4.0 HYBRID (E) T-MOBILE HI -CAP HYBRID FIBER ROUTED W/ (E) COAX (50 LF, 50 LF & 75 LF) HYBRID HYBRID ' HYBF ID COAX HYBRID - COAX E) T-MOBILE PURCELL CABINET TO REMAIN (1) (E) RECTIFIER IN (E) PDU 1 (E) T-MOBILE COVP AT EQUIP. (TYP. OF 3) TO REMAIN W S 1 (E) ENLARGED EQUIPMENT PLAN SCALE: 1 /2"= 1'-0" (11X17) SCALE: 1" = 1'-0" (22X34) 0' 1' 2' 4' IM i ROUTE OF (12) (E) T-MOBILE (7/8") COAX (N) T-MOBILE ANTENNAS & ANCILLARY EQUIPMENT; SEE SHEET A4.0 HYBR COAX HYBRID HYBRID FIECEVED DEC 112015 Community Development (E) T-MOBILE HI -CAP HYBRID FIBER ROUTED W/ (E) COAX (50 LF, 50 LF & 75 LF) HYBRID (E) T-MOBILE PURCELL CABINET TO REMAIN (1) (E) RECTIFIER IN (E) PDU (E) T-MOBILE COVP AT EQUIP. (TYP. OF 3) TO REMAIN WITHIN (E) T-MOBILE CABINET, 7 INSTALL THE FOLLOWING EQUIPMENT: " (2) FSMF • (2) FBBC • (1) ESMB REPLACE U1900 SYSTEM MODULE W/: "(1) FSMF " (1) FBBC 16.05° 2 (N) ENLARGED EQUIPMENT PLAN SCALE: 1/2"=1'-0" (11X17) SCALE: 1" =1'-0" (22X34) 0' 1' 2' 4' ■ i� --Mobile- 4)CENTERLINE Aden ig Maker N m* \ V / ■ n • I Il R e ae 11/12/15 EXP. 1/27/16 CPM PROJECT NO.: 8856 PRELIMINARY NO. DATE D/C DESCRIPTION 0 10-22-15 MS/MS 90% CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT SUBMITTAL NO. DATE D/C DESCRIPTION 1 11-11-15 MS/MS BP SUBMITTAL SITE NAME: SOUTHCENTER PLACE SITE ID: SE04000B SITE ADDRESS: 16400 SOUTHCENTER PARKWAY TUKWILA, WA98188 SHEET TITLE ENLARGED EQUIPMENT PLAN SHEET NO. A2.0 (E) T-MOBILE PANEL ANTENNAS IN GAMMA SECTOR, TOTAL OF (2), TO BE REMOVED (E) T-MOBILE ANTENNA TIP HEIGHT ® ® ® iYYY 1� 10� i �y T��JJJ 111e� 81.3' \ (E) T-MOBILE PANEL ANTENNAS IN ALPHA AND (E) T-MOBILE ANTENNA RAD CNTR. BETA SECTOR, TOTAL OF (4), TO REMAIN I� C E N T E R L I N E *Mindy t44d‘sANt•cnb 78.3' 8 78.8' \ At (E) TOP OF PENTHOUSE C li �t1 T-MOBILE FRLB MOUNTED BEHIND 73.0' —_,_— r (E) ANTENNA ON (E) PIPE MOUNT (TYP :) OF 1 PER SECTOR, 3 TOTAL) "� /t (E) TOP OF ROOF )11 n Pn •IIIRS '4'62.8' -- --- T-MOBILE BTS EQUIPMENT TO REMAIN � I i (E) _ _ (E) T-MOBILE FRIG (RRU) (TYP OF 1 �" PER SECTOR, 3 TOTAL) TO REMAIN 1 j I I 1 j (E) T-MOBILE COVP (TYP OF 1 PER SECTOR, 3 TOTAL) TO REMAIN • L rt _ \ BUILDING (E) T-MOBILE DIPLEXER (TYP OF 2 PER SECTOR, 6 TOTAL) TO REMAIN I I I I I , I r i (E) 1. ''�r° 1 (E) T-MOBILE TMA (TYP OF 2 PER L _ SECTOR, 6 TOTAL) TO REMAIN a- ! ✓ " d r y� � 'i (E) T-MOBILE FXFB (RRU) (TYP OF 1 PER SECTOR, 3 TOTAL) TO REMAIN (E) GRADE 0.0' AGL i I SCALE: 1"=2o'-0"(„X,7) o' ,o' 20' 40'� 1 EXISTING NE ELEVATION SCALE: 1" = 10'-0" (22X34) III III 11/12/15 EXP. 1/27/16 T-MOBILE PANEL ANTENNAS IN GAMMA (NOTES: (N) T-MOBILE ANTENNA TIP HEIGHT (N) SECTOR ONLY (TYP OF 3) MOUNTED ON (E) (E) T-MOBILE ANTENNA TIP HEIGHT ,� CPM PROJECT NO.: 8856 81.3' Ain (N) T-MOBILE ANTENNA RAD CNTR. \ & (N) WALL PIPE MOUNTS (E) T-MOBILE / ANTENNA 81.3' 1 RAD CNTR. di • IF REQUIRED, PAINT TO MATCH ANTENNAS AND ANCILLARY EQUIPMENT TO MATCH - THE EXISTING STRUCTURE WITH NON -REFLECTIVE PAINT AS REQ'D. CONTRACTOR PRELIMINARY NO. DATE D/C DESCRIPTION 78,3 & 78.8 TO VERIFY COLOR AND FINISH WITH LANDLORD AND/OR JURISDICTION. 78.3' & 78.5' \ i / • PRIOR TO MATERIALS PROCUREMENT CONTRACTOR SHALL FIELD VERIFY 0 10-22-15 MS/MS 90% CD REVIEW E TOP OF PENTHOUSE /I. { ) "- CONDITION OF STRUCTURE AT PROPOSED MOUNTING LOCATION TO ENSURE EXISTING CONDITIONS ARE SUITABLE AT SPECIFIED ELEVATION. 1 11-11-15 MS/MS CLIENT COMMENT `r 73.0' I � r (E) T-MOBILE PANEL BETA SECTOR, ANTENNAS IN ALPHA TOTAL OF (4), TO REMAIN AND •NEW ANTENNAS SHALL NOT EXCEED EXISTING TIP HEIGHT U.N.O. • RETURN ALL USED EQUIPMENT AND HARDWARE TO T-MOBILE WAREHOUSE. SUBMITTAL • �:= � s• • ALL CLIMBING PATHS ON TOWER/MONOPOLE TO REMAIN FREE & CLEAR OF NO. DATE D/C DESCRIPTION ( MOUNTS, EQUIPMENT, ETC. (E) TOP OF ROOF .11A (E) T-MOBILE FRLB MOUNTED BEHIND 1 11-11-15 MS/MS BP SUBMITTAL 62.8' ANTENNA ON (E) PIPE MOUNT (TYP (N) T-MOBILE FRIG (RRU) MOUNTED BEHIND (N) ANTENNA ON (N) PIPE MOUNT 1 OF 1 PER SECTOR, ' i (E) T-MOBILE FXFB 3 TOTAL) I ' 1 (RRU) (TYP OF 1 i ( j SITE NAME; PER SECTOR, 3 TOTAL) TO REMAIN SOUTHCENTER PLACE SITE ID: (E) T-MOBILE BTS EQUIPMENT TO REMAIN (N) T-MOBILE FXFC, MOUNTED ON (E) 11 T- - PLATFORM W/ (E) FXFB UNIT ... - - _ S E04000 B SITE (N) T-MOBILE DIPLEXERS, TYP OF (6), (8 I TOTAL), TO BE MOUNTED BEHIND (N) HBXX MODE (STING ANTENNAS (3 NEW 8 1 EXISTING PER ANTENNA) ; � I 1 I L ;_ 1 � - _T__ I �� V �J 5q SOUTHCADDFtEENTER 16400 SOUTHCENTER PARKWAY TUKWI A 98188 4/ (E) T-MOBILE FRIG (RRU) (TYP OF 1 PER SECTOR, 3 TOTAL) TO REMAIN T-MOBILE T PER i I r I �'��.� V �f � SHEET THEE ELEVATIONS (E) OR, , 3TOTAL) VP SECTOR, 3 TTO REMAIN L) (E) T-MOBILE DIPLEXER (TYP OF 2 PER SECTOR, 6 TOTAL) TO REMAIN (E) T-MOBILE TMA (TYP OF 2 PER SECTOR, 6 TOTAL) TO REMAIN DEC 112015 Develoo UnComey pment SHEET NO. A3 . 0 SCALE: 1" = 20'-0" (11X17) 0' 10' 20' 40' 2 FINAL NE ELEVATION SCALE: 1"=10'-0"(22X34) al E GAMMA SECTOR sM01 ANTENNA SCHEDULE - FINAL CONFIGURATION y '; a S 7 ,c Cy m �x 5��2 q o1 (E) T-MOBILE FRIG (RRU) (TYP OF 1 T,? PER RELOCATED R, 3 TOTAL) TO BE o O w °', S./3 (E) T-MOBILE COVP (TYP OF 1 PER SECTOR, 3 T-MOBILE ANTENNAS, TYP OF (2) IN / '•. ;-' TOTAL) TO REMAIN GAMMA SECTOR ONLY, TO BE REMOVED (E).�� (E) T-MOBILE DIPLEXER (TYP OF 2 PER (E) T-MOBILE FXFB (RRU) (TYP OF 1 SECTOR, 6 TOTAL) TO REMAIN PER SECTOR, 3 TOTAL) TO REMAIN ' ,�: (E) T-MOBILE TMA (TYP OF 2 PER 6' SECTOR, 6 TOTAL) TO REMAIN 9‘ay )y 706, 70 Se (E) PENTHOUSE; CAPACITY O° TO SUPPORT THE 6�®.• PROPOSED LOADING �p�'ry� ' "' CONFIGURATION TO BE }' ,`ti ANALYZED BY OTHERS (E) T-MOBILE PANEL �� Q'S` ANTENNAS, TYP OF (4) TO Q 16.05° �0� 0 ✓� REMAIN d`o . N Ztr i)- y�6' TN MN 0� (E) T-MOBILE FRLB MOUNTED BEHIND ti B}' ALPHA SECTOR SECTOR POS. EXIST. / NEW MNFR. ANTENNA MODEL PORT DIMENSIONS (L x W x D) WEIGHT (LBS) CENTERLINE Adwxig W5•f•ttAM•ab Al EXISTING ANDREW TMBXX-6516-R2M QUAD 59.0" x 11.9" x 6.3" 34.6 ALPHA A2 EXISTING COMMSCOPE SBNHH-1D656 HEX 72.6" x 11.9" x 7.1" 40.6 B1 EXISTING ANDREW TMBXX-6516-R2M QUAD 59.0" x 11.9" x 6.3" 34.6 BETA B2 EXISTING COMMSCOPE SBNHH-1D65B HEX 72.6" x 11.9" x 7.1" 40.6 Cl NEW COMMSCOPE HBXX-3319DS-A2M QUAD 57.0" x 22.2" x 4.9" 38.1 n CTOR ■ • i n ■ ■ R • GAMMA C2 NEW COMMSCOPE DBXNH-6565E-A2M QUAD 72.7" x 11.9" x 7.1" 46.3 DELTA D3 NEW COMMSCOPE HBXX-3319DS-A2M QUAD 57.0" x 22.2" x 4.9" 38.1 *TOWER - FINAL EQUIPMENT INVENTORY SCOPE QTY. TECHNOLOGY MNFR. MODEL DIMENSIONS (L X W X D) WEIGHT (LBS) (E) TO REMAIN (2) ANTENNA ANDREW TMBXX-6516-R2M 59.0" x 11.9" x 6.3" 34.6 REMOVE (E) (1) ANTENNA ANDREW TMBXX-6516-R2M 59.0" x 11.9" x 6.3" (34.6) (E) TO REMAIN (2) ANTENNA COMMSCOPE SBNHH-1 D656 72.6" x 11.9" x 7.1" 40.6 / " 11/12/15 I. ,« i - j� .� _� ° i ( a �p T !k'.Y$S y A ' EXP. 1/27/16 REMOVE (E) (1) ANTENNA COMMSCOPE SBNHH-1 D65B 72.6" x 11.9" x 7.1" (40.6) ADD (N) (1) ANTENNA COMMSCOPE DBXNH-6565B-A2M 72.7" x 11.9" x 7.1" 46.3 ADD (N) (2) ANTENNA COMMSCOPE HBXX-3319DS-A2M 57.0" x 22.2" x 4.9" 38.1 (E) TO REMAIN (3) RRU NOKIA FXFB 19.3" x 22.0" x 5.2" 55.0 ANTENNA ON (E) PIPE MOUNT (TYP '60 W E (E) TO REMAIN (3) RRU NOKIA FRIG 23.8" x 17.2" x 7.5" 59.9 4- BETA SECTOR ��' OF 1 PER SECTOR, 3 TOTAL) ./,x d0°QA, ADD (N) (1) RRU NOKIA FRIG 23.8" x 17.2" x 7.5" 59.9 SA ADD (N) (1) RRU NOKIA FXFC 19.3" x 22.0" x 5.2" 55.0 SCALE: NTS (11X17) (E) TO REMAIN (3) COVP RAYCAP CR100-1076R06 20.2" x 19.0" x 7.0" 15.0 2 EXISTING ANTENNA PLAN SCALE: NTS (22X34) (E) TO REMAIN (6) TMA ANDREW DU (DUAALL AWSWS/PCSCS) 9.4" x 7.3" x 3.5" 13.9 (N) T-MOBILE PANEL ANTENNAS (TYP OF 1) OAMMA SECTOR 0 2 MOUNTED ON (N) WALL PIPE MOUNT,' SEE 1/A6.0 7� CPM PROJECT NO.: 8856 PRELIMINARY (E) TO REMAIN (6) DIPLEXER COMMSCOPE ECC1920-VPUB 7.6" x 7.3" x 2.6" 7.9 �� (N) T-MOBILE FRIG (RRU) MOUNTED BEHIND (N) ANTENNA y><y ON (N) PIPE MOUNT BELOW (E) RELOCATED FRIG �y " c�-4,-+ �905,ft /5- ` x) �I v(L (N) T-MOBILE PANEL ANTENNAS (TYP OF 2) ?QMOUNTED ON (E) WALL PIPE MOUNTS;(E) SUITABILITYOF MOUNT FOR FINAL LOADING CONFIGURATION TO BE VERIFIED BY • OTHERS PRIOR TO INSTALLATION (E) T-MOBILE COVP (TYP NO. DATE D/C DESCRIPTION ADD (N) (6) DIPLEXER COMMSCOPE ECC1920-VPUB 7.6" x 7.3" x 2.6" 7.9 0 10-22-15 MS/MS 90%CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT SUBMITTAL *GROUND - FINAL EQUIPMENT INVENTORY NO. DATE D/C DESCRIPTION QTY. TECHNOLOGY MNFR. MODEL DIMENSIONS X W X D) WEIGHT, (LBS) 1 11-11-15 MS/MS BPSCOPE TO REMAIN (3) COVP RAYCAP RNSNDC-7771-PF-48 18.85" x 16.08" x 5.83" 19.0 SITE NAME: Fi Ea. C F !7 �.. 1 .•.. O DEC 112015 SOUTHCENTER PLACE SITE ID: �-- (N) T-MOBILE DIPLEXERS, TYP OF (3), (6 OF 1 PER SECTOR, 3 K. TOTAL), TO BE MOUNTED BEHIND (N) �'\ TOTAL) TO REMAIN (E) T-MOBILE FXFB (RRU) (TYP OF 1 HBXX MODEL ANTENNAS PER SECTOR, 3 TOTAL) TO REMAIN (N) T-MOBILE M W/ (E) FXDFB UNIT (E) T-MOBILE TMA (TYP OF 2 PER F SECTOR, 6 TOTAL) TO REMAIN glo`s6,I y�-��'/ , �sSB /, "'O° (E) PENTHOUSE; CAPACITY �L� TO SUPPORT THE ^ti° PROPOSED LOADING .i_54.0 CONFIGURATION TO BE fit' orl' ANALYZED BY OTHERS (E) T-MOBILE PANEL ANTENNAS, TYP OF (4) TO tr, 4' REMAIN �� co° ��ry0 FT TN (E) T-MOBILE FRLB MOUNTED BEHIND Ay�eG ALPHA SECTOR 8.05° N MN SE04000B $ ADDRESS:ITE • THE "TOWER" AND "GROUND" REFERENCES REFER TO NOMENCLATURE REFLECTED IN THE PLUMBINy V�� RAM AND DO NOT NECESSARILY REFER TO ACTUAL LOCATION OF EQUIPMENT. L `�-,e GROUND EQUIPMENT NOTE �7 'J�1'h, ON TbT RF1.0 SHEET oilmen 16400 SOUTHCENTER PARKWAY TUKWILA, WA98188 • NEW FBBC TO BE INSTALLED IN EXISTING FCOA CABINET (QUANTITIES MAY VARY). ALL OTHER BASEBAND MODULES ARE ASSUMED TO BE EXISTING. ANTENNA NOTES: SHEET TITLE ANTENNA DETAILS & PLANS • REFERENCE OWNERS MANUAL FOR CONNECTION AND MOUNTING INFORMATION FOR AMPLIFIER IF REQUIRED. • CONTRACTOR SHALL VERIFY FINAL ANTENNA AZIMUTHS W/ CLIENT REPRESENTATIVE PRIOR TO COMMENCING INSTALLATION. • PRIOR TO MATERIALS PROCUREMENT CONTRACTOR SHALL FIELD VERIFY SUITABILITY OF ANTENNA MOUNT AT SPECIFIED ELEVATION. • IF REQUIRED, PAINT TO MATCH ANTENNAS AND ANCILLARY EQUIPMENT TO MATCH THE EXISTING STRUCTURE WITH NON -REFLECTIVE PAINT AS REQ'D. CONTRACTOR TO VERIFY COLOR AND FINISH WITH LANDLORD AND/OR JURISDICTION. • RETURN ALL UNUSED EQUIPMENT TO T-MOBILE WAREHOUSE. SHEET NO. y0t�' ANTENNA ON (E) PIPE MOUNT (TYP `ss W ./P � BETA SECTOR 0OF 1 PER SECTOR, 3 TOTAL) ``��Q,Q E A4.0 O ?� S EQUIPMENT SCALE: NTS (11X17) SCALE: NTS (11X17) 3 FINAL ANTENNA PLAN SCALE: NTS (22X34) 1 ANTENNA AND ANCILLARY SCALE: NTS (22X34) TOP FRONT 1- _ w _ EPT SIDE ANTENNA DATA MECHANICAL SPECIFICATIONS MANUFACTURER HEIGHT WIDTH DEPTH WEIGHT COMMSCOPE 72.7 IN 11.9 IN 7.1 IN 46.3 LBS PART # CONNECTORS STANDARD MOUNTING HARDWARE DBXNH-6565B-A2M (4) 7-16 DIN FEMALE INCLUDED FRONT 1- _ 0 w _ SIDE ANTENNA DATA MECHANICAL SPECIFICATIONS MANUFACTURER HEIGHT WIDTH DEPTH WEIGHT COMMSCOPE 57.0 IN 22.2 IN 4.9 IN 38.1 LBS PART# CONNECTORS STANDARD MOUNTING HARDWARE HBXX-3319DS-A2M (4) 7-16 DIN FEMALE INCLUDED TOP FRONT WIDTH 1- _ 0 w DEPTH NSN FRLB LTE 700 / BAND 12 (REMOTE RADIO UNIT) HEIGHT: 15.75" WIDTH: 15.75" DEPTH 5.9" WEIGHT: 59.52 LBS SIDE 1 ANTENNA DETAIL SCALE: NTS (11X17) SCALE: NTS (22X34) 2 ANTENNA DETAIL SCALE: NTS (11X17) SCALE: NTS (22X34) 3 FRIG (RRU) DETAIL SCALE: NTS (11X17) SCALE: NTS (22X34) TOP FRONT WIDTH 1- w _ fEPTHT NOIUA FXFC (REMOTE RADIO UNIT) HEIGHT: 19.3" WIDTH: 22.0" DEPTH 5.2" WEIGHT: 55.0 LBS SIDE TOP FRONT WIDTH ECC1920-VPUB (DIPLEXER) HEIGHT: 7.6" WIDTH: 7.3" DEPTH 2.6" WEIGHT: 7.9 LBS SIDE RECEIVED DEC 112015 Community Development Lis% Q O f 4 FXFC (RRU) DETAIL SCALE: NTS (11X17) SCALE: NTS (22X34) 6 DIPLEXER DETAIL SCALE: NTS (11X17) SCALE: NTS (22X34) 7 NOT USED SCALE: NTS (11X17) SCALE: NTS (22X34) ° T. ° 'Mobile 4CENTERLINE Aolhcbq WailmAYMabl *ECTOR e;- + ' CV AL P .'M [ T y • °.,' o 11/12/15 EXP. 1/27/16 CPM PROJECT NO.: 8856 PRELIMINARY NO. DATE D/C DESCRIPTION 0 10-22-15 MS/MS 90% CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT SUBMN TAL NO. DATE D/C DESCRIPTION 1 11-11-15 MS/MS BP SUBMITTAL _ SITE NAME: SOUTHCENTER PLACE SITE ID: SE04000B SITE ADDRESS: 16400 SOUTHCENTER PARKWAY TUKWILA, WA 98188 SHEET TITLE ANTENNA AND EQUIPMENT DETAILS SHEET NO. A5.0 NOTES: - SUITABILITY OF PLATFORM / MOUNT(S) FOR FINAL LOADING CONFIGURATION TO BE VERIFIED BY OTHERS PRIOR TO INSTALLATION. NO WORK SHALL COMMENCE WITHOUT THE APPROVED STRUCTURAL TOWER / ANTENNA / MOUNT ANALYSIS REPORT (SIGNED AND SEALED) TO BE PROVIDED UNDER SEPARATE COVER. CONTRACTOR PRIOR TO CONSTRUCTION SHALL REVIEW THE APPROVED TOWER / ANTENNA / MOUNT ANALYSIS REPORT SUPPLIED BY T-MOBILE AND MODIFY, IF REQUIRED, ALL APPLICABLE MEMBERS AS INDICATED IN CERTIFIED STRUCTURAL REPORT PRIOR TO INSTALLATION ON STRUCTURE. (N) T-MOBILE FRIG MOUNTED BEHIND ANTENNA ON (E) PIPE MOUNT (TYP OF 1 PER SECTOR, 3 TOTAL) (N) T-MOBILE PANEL ANTENNA (TYP OF 1) MOUNTED ON (N) WALL PIPE MOUNTS (N) T-MOBILE DIPLEXER (TYP OF 3) TO BE MOUNTED BEHIND (N) ANTENNA (N) 3" STD. MIN. ANTENNA PIPE (2) (N) VALMONT PART #WWM01 OR APPROVED EQUAL STANDOFF BRACKETS OR (E) MICROWAVE TOWER SERVICE PART #M222 ADJUSTABLE WALL MOUNTS WITH (4) 1/2" ALL -THREAD RODS W/ 4" MIN. EMBED., W/ SIMPSON "EPDXY -TIE" GROUT, TYP. TOP AND BOTTOM (E) MIN. 10" THICK CONCRETE WALL (VERIFY) 2 NOT USED SCALE: NTS (11X17) SCALE: NTS (22X34) L/5Oa5 7 RECEVED DEC 112015 Community Development 1 ANTENNA MOUNTING DETAIL SCALE: NTS (11X17) SCALE: NTS (22X34) 3 NOT USED SCALE: NTS (11X17) SCALE: NTS (22)(34) ob11e - ®® ,< ►CENTERLINE Advancing Mikes N tNatb ECTOR ■ n • I It ■ ■ R • 11/12/15 EXP. 1/27/16 CPM PROJECT NO.: 8856 PRELIMINARY NO. DATE D/C DESCRIPTION 0 10-22-15 MS/MS 90% CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT SUBMITTAL NO. DATE D/C DESCRIPTION 1 11-11-15 MS/MS BP SUBMITTAL SITE NAME: SOUTHCENTER PLACE SITE ID: SE04000B SITE ADDRESS: 16400 SOUTHCENTER PARKWAY TUKWILA, WA 98188 SHEET TITLE CONSTRUCTION DETAILS SHEET NO. A6.0 • RFDS V. 7 - SECTOR SPLIT Alpha & Bea (Only Alpha Is shcwn) NSN Configuration 705J (N_705JRUSh 4spiit 012) u21a0 vat Split — 2015 4-paw paw SAeS eo h Koot l op ,t -_U ...:ont epusu& t't:S Sp.ctnsrr, Fit;; .Nava! Split to Support LT! Spectrum m=15 MHZ 1 Fod o Monde pe+r aac:or iA•.bm.a vd....y Aw».+w iuxm n6 `m z. w;run d,ns r-__.• I'--1-- :w A1•.3 •.n"" m • rv,».Jxr-0 NOTES: 1. ALL COAXIAL CABLE CONNECTIONS TO BE WEATHERPROOFED. 2. CONTRACTOR TO DIP CABLES AND JUMPERS WHERE NECESSARY. 3. TAGGING: m ALL COAXIAL CABLES TO BE MARKED WITH COLOR CODED TAPE TO INDICATE THE ANTENNA SECTOR. • COLORED ELECTRICAL TAPE SHALL MARK EACH END OF CABLE AND EACH END OF JUMPERS AS CLOSE TO EACH END AS POSSIBLE. (NOT TO INTERFERE WITH WATERPROOFING.) 4. COAXIAL CABLE SPECIFICATIONS REQUIRE CABLE SUPPORT EVERY 3'-0" ON CENTER. CONTRACTOR SHALL SUPPLY SUPPORTS AS REQUIRED TO MEET THIS REQUIREMENT. 5. VERTICAL CONNECTIONS SHALL BE TAPED FROM THE BOTTOM UP SO OVERLAP MOVES WATER AWAY FROM CONNECTION (SEE STEP 4). 6. PROVIDE HEAT SHRINK IN PLACE OF TAPE FOR QUAD POLES & TMAS. 7. ALL ANTENNAS & COAXIAL ANTENNA CABLE TO BE FURNISHED BY T-MOBILE AND INSTALLED BY CONTRACTOR. 8. COAX SHALL BE TAGGED WITH COLOR CODING AT (2) PLACES USING 1" WIDE WEATHERPROOF COLORED VINYL TAPE AT THE FOLLOWING LOCATIONS: #1 - AT ANTENNA CONNECTION #2 -AT ENTRY TO EQUIPMENT CABINET 9. RUN COAXIAL CABLE WITH MINIMUM 12" SLACK & 12" FROM EDGE OF EQUIPMENT CABINETS, ACROSS WAVE GUIDE BRIDGE (IF APPLICABLE), UP TO TOWER LEG (IF APPLICABLE), AND DISTRIBUTE TO EACH ANTENNA DEVICE. FURNISH AND INSTALL A MINIMUM OF (3) GROUND KITS PER COAXIAL CABLE. VERIFY NUMBER OF ANTENNAS, CABLE, AND CABLE DIAMETER WITH T-MOBILE CONSTRUCTION MANAGER. RECFiVED DEC 112015 Community Development 1 RF DETAILS - ANTENNA & ANCILLARY EQUIPMENT PLUMBING DIAGRAM T —Mobile <>CENTERLINE *heady Maims Mao& )\f s n e i n e s R s ' a F .' A . 11/12/15 EXP. 1/27/16 CPM PROJECT NO.: 8856 PRELIMINARY NO. DATE D/C DESCRIPTION 0 10-22-15 MS/MS 90% CD REVIEW 1 11-11-15 MS/MS CLIENT COMMENT SUBMITTAL NO. DATE D/C DESCRIPTION 1 11-11-15 MS/MS BP SUBMITTAL SITE NAME: SOUTHCENTER PLACE SITE ID: SE04000B SITE ADDRESS: 16400 SOUTHCENTER PARKWAY TUKWILA, WA 98188 SHEET TITLE RF DETAILS SHEET NO. RF1.0