The URL can be used to link to this page

Home My WebLink AboutPermit PL18-0028 - AT&T WIRELESS - WIRELESS FACILITYAT&T WIRELESS 0040000315 PARENT FILE PL18-0028 THIS. FILE L18-0036 WIRELESS FACILITY/TYPE 1 )City of Tukwila Department of Community Development - Jack Pace, Director June 15, 2018 NOTICE OF DECISION TO: Drew Parker, Mastec Network Solutions (OBO AT&T Wireless) Ark Via Nelle, LLC King County Assessor, Accounting Division Agencies with Jurisdiction All Parties of Record Allan Ekberg, Mayor This letter serves as a notice of decision and is issued pursuant to TMC 18.104.170 on the following project and permit approval. I. PROJECT INFORMATION Project File Number: L18-0036; PL18-0028 Applicant: Drew Parker, Mastec Network Solutions (OBO AT&T Wireless) Type of Permit Applied for: Type 1 Wireless Facilities Permit Project Description: The applicant is proposing modifying the existing building mounted wireless communications facility by removing three (3) existing panel antenna, three (3) existing TMAS, relocating three (3) existing antennas and three (3) existing RRHS. They will also install three (3) panel antenna, three (3) RRHS, three (3) 4C BCEM Cards and three (3) Cordex Rectifiers. The project also qualifies as an Eligible Facilities Modification under § 6409 of the FCC's Spectrum Act, which requires the City to approve any eligible facilities request for a modification of an existing tower or base station that does not substantially change the physical dimensions of such tower or base station. This proposal is not considered a substantial change under the Tukwila Municipal Code 18.58.200.7, and falls within the guidelines for an eligible facilities modification. Location: Parcel 0040000315-located at 3516 South 146th Street, Tukwila WA 98168 Associated Files: PL18-0028 Comprehensive Plan High Density Resedential (HDR) Designation/Zoning District: Tukwila City Hall • 6200 Southcenter Boulevard • Tukwila, WA 98188 • 206-433-1800 • Website: TukwilaWA.gov II. DECISION SEPA Determination: The City SEPA Responsible Official has determined that this application does not require a SEPA threshold determination because it is categorically exempt. Decision on Substantive Permit: The Community Development Director has determined that the application for a Wireless Telecommunication Facility does comply with applicable City and state code requirements and has approved this application with the following condition. III. YOUR APPEAL RIGHTS The Decision on this Permit Application is a Type 1 decision pursuant to Tukwila Municipal Code §18.104.010. Other land use applications related to this project may still be pending. No administrative appeal of a DNS or an EIS is permitted. One administrative appeal to the City Hearing Examiner of the Decision on the Permit itself is permitted. If an MDNS was issued, any person wishing to challenge either the conditions which were imposed by the MDNS decision or the failure of the Department to impose additional conditions in the MDNS must raise such issues as part of the appeal to the Hearing Examiner. A party who is not satisfied with the outcome of the Hearing Examiner appeal process may file an appeal in King County Superior Court from the Hearing Examiner's decision. IV. PROCEDURES AND TIME FOR APPEALING To appeal the Community Development Director decision on the Permit Application, a written notice of appeal must be filed with the Department of Community Development within 14 days of the issuance of this Decision. The requirements for such appeals are set forth in Tukwila Municipal Code Ch. 18.116. All appeal materials shall be submitted to the Department of Community Development. Appeal materials MUST include: 1. The name of the appealing party. 2. The address and phone number of the appealing party; and if the appealing party is a corporation, association or other group, the address and phone number of a contact person authorized to receive notices on the appealing party's behalf. 3. A statement identifying the decision being appealed and the alleged errors in the decision, including any specific challenge to an MDNS. 4. The Notice of Appeal shall identify (a) the specific errors of fact or errors in application of the law in the decision being appealed; (b) the harm suffered or anticipated by the appellant, and (c) the relief sought. The scope of an appeal shall be limited to matters or issues raised in the Notice of Appeal. 5. Appeal fee per the current fee schedule, additional hourly charges may apply. In addition, all hearing examiner costs will be passed through to the appellant. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov V. APPEAL HEARINGS PROCESS Any administrative appeal regarding the Permit shall be conducted as a closed record hearing before the Hearing Examiner based on the information presented to the Community Development Director, who made the original decision. No new evidence or testimony will be permitted during the appeal hearing. Parties will be allowed to present oral argument based on the information presented to the Community Development Director before their decision was issued. The Hearing Examiner's decision on the appeal is the City's final decision. Any party wishing to challenge the Hearing Examiner's decision on this application must file an appeal pursuant to the procedures and time limitations set forth in RCW Ch. 36.70C. An appeal challenging a DNS, an MDNS or an EIS may be included in such an appeal. If no appeal of the Hearing Examiner's decision is properly filed in Superior Court within such time limit, the Decision on this permit will be final. The City's decision to issue a DNS, an MDNS or an EIS is final for this permit and any other pending permit applications for the development of the subject property. VI. INSPECTION OF INFORMATION ON THE APPLICATION Project materials including the application, any staff reports, and other studies related to the permits are available for inspection at the Tukwila Department of Community Development, 6300 Southcenter Blvd., Suite 100, Tukwila, Washington 98188 from Monday through Friday between 8:30 a.m. and 5:00 p.m. The project planner is Jonathan Joseph, who may be contacted at 206-431-3662 for further information. Property owners affected by this decision may request a change in valuation for their property tax purposes. Contact the King County Assessor's Office for further information regarding property tax valuation changes. Depament of ommunity Development City Tukwila Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov City of Tukwila Allan Ekberg, Mayor Department of Community Development - Jack Pace, Director NOTIFICATION: FILE NUMBER: APPLICANT: PROPERTY OWNER: REQUEST: LOCATION: ASSOCIATED PERMITS: SEPA DETERMINATION: COMPREHENSIVE PLAN DESIGNATION: ZONE DESIGNATION: STAFF: ATTACHMENTS: Staff Report PREPARED June 15, 2018 Notification is not required for a Type 1 land use application. L18-0036; PL18-0028 Drew Parker, Mastec Network Solutions (OBO AT&T Wireless) Ark Via Nelle, LLC Approval of a Type 1 Wireless Telecommunications Facilities Permit to modify the existing building mounted concealed wireless communications facility by removing three (3) existing panel antenna, three (3) existing TMAS, relocating three (3) existing antennas and three (3) existing RRHS. They will also install three (3) panel antenna, three (3) RRHS, three (3) 4C BCEM Cards and three (3) Cordex Rectifiers. Parcel 0040000315-located at 3516 South 146th Street, Tukwila WA 98168 Electrical permits issued through the City of Tukwila will be required for service alteration for any other electrical service work that is anticipated but not noted on the plans, per article 85.12 (B), Washington electrical code. Building and mechanical permits are required for scope of work stated on the submitted plans. Exempt High Density Residential (HDR) High Density Residential (HDR) Jonathan Joseph, Planning Intern Project Plans for Permit L18-0036 Tukwila City Hall • 6200 Southcenter Boulevard • Tukwila, WA 98188 • 206-433-1800 • Website: TukwilaWA.gov Page 2 FINDINGS Vicinity/Site Information Project Description The applicant is proposing modifying the existing building mounted wireless communications facility by removing three (3) existing panel antenna, three (3) existing TMAS, relocating three (3) existing antennas and three (3) existing RRHS. They will also install three (3) panel antenna, three (3) RRHS, three (3) 4C BCEM Cards and three (3) Cordex Rectifiers. The project also qualifies as an Eligible Facilities Modification under § 6409 of the FCC's Spectrum Act, which requires the City to approve any eligible facilities request for a modification of an existing tower or base station that does not substantially change the physical dimensions of such tower or base station. This proposal is not considered a substantial change under the Tukwila Municipal Code 18.58.200.7, and falls within the guidelines for an eligible facilities modification. Existing Development This telecommunications facility is preexisting. Surrounding Land Uses The property is zoned high Density Residential (HDR). Surrounding parcels are zoned within the HDR zone. The parcel east of this parcel is zoned Neighborhood Commercial Center (NCC) zone. South 146th Street is south of this parcel. Background In 2006, the City adopted a Wireless Facilities Chapter (TMC 18.71) to the Zoning Code. The chapter provides location and design requirements for the placement of WCF within the City of Tukwila. In 2016 the city adopted amendments to this ordinance in compliance with the Federal Spectrum Act. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov Page 3 Location Selection Tukwila Municipal Code (TMC) provides a hierarchy of appropriate locations within the City. Generally, co - locations and utilizing existing structures are favored over the development of new standalone WCF within the City. TABLE. A Type of Ruud IRisgiutred, Based on Type of Wheless Communication Facility Zoning(1) Typo of Facility Residential Commercial tindusliial Adding antennas to an castihg tower or utikty lols Type WI Type 1¢J Type 1Qi IEigibEE facilities mollification Type 1 Type 1 Type 1 Ubhity pale co 1oc ation Type 2 Type 2 Type 2 Concealed b nng attached Type 2a► Typo 20} Type 1 tkion.concealed budding attached Type 2' } Typo 2 Type 1 Niew tom or height adjustment rat Type 3 't Type 3 Type 3 (1) Zoning for any private/public property or right-of-way Residential — LDR, MDR, or HDR Commercial — O, MUO, RCC, NCC, RC, RCM, TUC, C/LI or TVS Industrial - LI, HI, MIC/L, or MIC/H (2) Provided the height of the tower does not increase and the square footage of the enclosure area does not increase. (3) An applicant may request to install a non -concealed building attached facility, under TMC Section 18.58.150. The applicant is proposing modifying the existing building mounted wireless communications facility by removing three (3) existing panel antenna, three (3) existing TMAS, relocating three (3) existing antennas and three (3) existing RRHS. They will also install three (3) panel antenna, three (3) RRHS, three (3) 4C BCEM Cards and three (3) Cordex Rectifiers. This site will be a modification to the property and falls within an Eligible Facilities Modification of the Tukwila Municipal Code. Per TMC 18.58.200.7C. Design Standards The City provides specific design standards for the placement of WCF within the City of Tukwila. The table below indicates if the applicant's proposal complies with required standards. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov Page 4 Table 1 (See TMC 18.58.070 for further details) General Requirements Project does comply Project does not comply Not Applicable Notes 1. Generators or other devices which will create noise must comply with TMC 8.22 regarding noise. x . 2.Business License Requirement x 3.Only safety signage must be placed on the WCF. x 4. Accommodations for parking for maintenance personal must be provided. X This modification does not affect parking. 5. Towers shall either maintain a galvanized steel finish or be painted a neutral color so as to reduce its visual obtrusiveness. x 6. The design of all buildings and ancillary structures shall use materials, colors, textures, screening, and landscaping that will blend the tower facilities to the natural setting and built environment. x 7. Antennas shall have the same color scheme as the structure they are located on. x 8. WCF poles and towers shall only have safety lights if required by a government agency. X 9. No advertising is permitted on WCF X No advertising is proposed. 10. Each service provider shall be limited to an equipment enclosure of 360 square feet. x Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov Page 5 Table 2 (See TMC 18.58.100 for further details) Concealed Building Mounted Development Requirements Project Does Comply Project Does Not Comply Not Applicable Notes 1. The proposed facility must meet the height requirements of the applicable zoning category x 2. Are antennas placed in "Rooftop Appurtenances" which includes: church spire, chimney or fake chimney, elevator tower, mechanical equipment room, or other similar appurtenances required to be placed on the roof, but not intended for human occupancy. . x 3. Antennas must be concealed from view. x 4. If screening antennas, screens must be made of the same material and be the same color as the building. x 5. Antennas hall be painted to match the color scheme, of the buildings)/pole x 6. Feed lines and coaxial cables x Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov Page 6 should be located below the parapet of the rooftop 7. Cabinet equipment is located within the building or on the rooftop x 8. If the equipment is cabinet located on the ground, a 6- foot-tall fence surrounds it x 9. If equipment cabinet is on rooftop, screening must be consistent with the existing building. x CONCLUSIONS 1. The proposed modifications to the existing WCF will not significantly alter the conditions that currently exist and will not be materially detrimental to the public welfare or injurious to property or improvements in the vicinity. 2. As demonstrated in Table 1, the project meets all applicable development standards for a Type 1 WCF. 3. The proposed modifications will not alter the surrounding land uses in terms of traffic and pedestrian circulation, building or site design. 4. The proposed project is in keeping with the goals and policies of the Comprehensive Land Use Policy Plan. 5. The project also qualifies as an Eligible Facilities Modification under § 6409 of the FCC's Spectrum Act, which requires the City to approve any eligible facilities request for a modification of an existing tower or base station that does not substantially change the physical dimensions of such tower or base station. RECOMMENDATIONS The recommendation to the Director of Community Development is to approve this application for a Type 1 Wireless Telecommunications Facility permit with the following conditions: 1. Applicant must apply for a business license to operate the wireless communication facility at this location. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov Page 7 INFORMATIONAL ITEMS A City of Tukwila electrical permit is required for service alteration. A building and mechanical permit are required for the site work. Please note that the installation of an emergency power disconnect switch is required for Fire Department use. Contact Don Tomaso at 206-971-8723 to get more information about permit requirements for the power disconnect switch. Phone: 206-433-1800 • Email: Mayor@TukwilaWA.gov • Website: TukwilaWA.gov City of Tukwila Allan Ekberg, Mayor Department of Community Development - Jack Pace, Director Affidavit of Distribution Project Name: AT&T UPGRADES Project Number: PL18-0028 Associated File Number(s): L18-0036 Date Mailed: 6/28/18 Mailing requested by: JONATHAN JOSEPH Mailer's signature: ❑ Board of Adjustment Agenda Packet ❑ Notice of Application for ❑ Board of Appeals Agenda Packet Shoreline Mgmt Permit ❑ Determination of Non -Significance CX Notice of Decision ❑ Determination of Significance & Scoping Notice ❑ Mitigated Determination of Non - Significance ❑ Notice of Action ❑ Notice of Application Parties of Record: ❑ Notice of Public Hearing ❑ Notice of Public Meeting ❑ Official Notice ❑ Other: ❑ Shoreline Mgmt Permit ❑ Short Subdivision Agenda • • CITY OF TUKWILA Department of Community Development 6300 Southcenter Boulevard, Tukwila, WA 98188 Telephone: (206) 431-3670 WIRELESS TELE- COMMUNICATION FACILITIES APPLICATION FOR STAFF USE ONLY Planner: File Number: Lig-0030 Application Complete Date: Project File Number:" 7uy 2 " Application Incomplete Date: Other File Numbers: NAME OF PROJECT/DEVELOPMENT: AT&T Upgrades/SG19/RIVERTON NORTH/LTE 6C BRIEF DESCRIPTION OF PROJECT: AT&T equipment upgrades on existing rooftop cell site. CIRCLE TYPE : TYPE 1 TYPE 2 TYPE 3 Public Hearing Notices and Hearing Examiner Fees Apply. LOCATION OF PROJECT/DEVELOPMENT: Give street address or, if vacant, indicate lot(s), block and subdivision, access street, and nearest intersection. 3516 South 146th Street Tukwila, WA 98168 LIST ALL TAX LOT NUMBERS (this information may be found on your tax statement). 004000-0315 DEVELOPMENT COORDINATOR : The individual who: • has decision making authority on behalf of the owner/applicant in meetings with City staff, • has full responsibility for identifying and satisfying all relevant and sometimes overlapping development standards, and • is the primary contact with the City, to whom all notices and reports will be sent. Name: Drew Parker Address: 1351 E. Irving Park Road Itasca IL. 60143 Phone: 630-634-4932 E-mail: drew.parker@mastec.com Signature: Drew ?atkei' Date: 04/10/2018 RECEWED MAY 02 2018 Community Development WA@SHAREPOINT FOLDER RESTRUCTURE1Reference\APPL1CATIONS - Land Use Apps & Handouts\CURRENT LAND USE APPLICATIONS\DRAFT Wireless Communication FaciGgy.docx COMPLETE APPLICATION CHECKLIST The materials listed below must be submitted with your application. You may request a waiver from items on the checklist that are not applicable to your project. Please discuss this waiver request with City staff either at a pre - application meeting or at the time of application submittal. Application review will not begin until it is determined to be complete. Within 28 days of receiving your application, City staff will determine if it is complete based on the attached checklist. If not complete City staff will mail you a letter outlining what additional information is needed. If you do not submit requested materials within 90 days from the City's request for additional information the City may cancel your application. Check items submitted with application Information Required. - Additional materials may be required. APPLICATION MATERIALS: Items 1-9 are required for ALL Wireless Telecommunication Facilities. x 1. Application Checklist (1 copy) indicating items submitted with application. x 2. Completed Application Form and drawings (5 copies). 3. Four sets of plans prepared by a design professional. The plans shall include a vicinity map, site map, architectural elevations, method of attachment, proposed screening, location of proposed antennas, and all other information which accurately depicts the proposed project. Minimum size is 8 1/2" x 11". Plans shall be no greater than 24" x 36". x-Requested 4. Application Fee: See Land Use Fee Schedule. x 5. Completed and notarized Affidavit of Ownership and Hold Harmless Permission to Enter Property (1 copy attached). N/A 6. SEPA Environmental Checklist. SEPA is not required when the facility: i) Is a microcell and is to be attached to an existing structure that is not a residence or school and does not contain a residence or a school; ii) Includes personal wireless antennas, other than a microcell, and is to be attached to an existing structure (that may be an existing tower) that is not a residence or school and does not contain a residence or school, and the existing structure to which it is to be attached is located in a commercial, industrial, manufacturing, forest or agriculture zone; or iii) Involves constructing a personal wireless tower less than sixty feet in height that is located in a commercial, industrial, manufacturing, forest, or agricultural zone. x-6409a Cover Letter 7. A letter from the applicant describing the proposed project and describing compliance with the City's Code requirements stated in TMC Section 18.58. Include statement whether the proposal is considered a "substantial change" or not as defined by the FCC rules and TMC Section 18.58.200. N/A 8. Sensitive Area studies and proposed mitigation (if required). N/A 9. If an outdoor generator is proposed, a report prepared by an acoustical engineer demonstrating compliance with TMC Section 8.22, "Noise". If the application requires a Type 2 review these additional items are needed: 10. Four sets of photo simulations that depict the existing and proposed view of the proposed facility; 11. Materials board for the screening material; 12. Landscaping plan; 13. Letter from a radio frequency engineer that demonstrates that the facility meets Federal requirements for allowed emissions; 14. If the facility is located within a residential zone, •a report from a radio frequency engineer explaining the need for the proposed wireless communication facility at that location. tkddi•Qn ' ally t',all .. le N.e W:\JSHAREPOINT FOLDER RESTRUCTURE \Reference\APPLCATIONS - Land Use Apps & Hnndouts\CURRENT LAND USE APPLICATIONS\DRAFT Wireless Communication Faeiliry.doc, MAY 02 2018 Community nnvnlnnrnnn. CITY OF TUKWILA Department of Community, Development 6300 Somhcenier Boulevard, Tukwila, WA 98188 Telephone: (206) 431-3670 AFFIDAVIT OF OWNERSHIP AND HOLD HARMLESS PERMISSION TO ENTER PROPERTY STATE OF WASHINGTON ss COUNTY OF KING The undersigned being duly sworn and upon oath states as follows: 1. I am the current owner of the property which is the subject of this application. 2. All statements contained in the applications have been prepared by me or niy agents and are true and correct to the best of my knowledge. 3. The application is being submitted with my knowledge and consent. 4. Owner grants the City, its em Ioyees, agents engineers contractors or other representatives the right to enter upon Owner's real property, located at 3516 South 146th Street Tukwila, WA 98168 for the purpose of application • review, for the limited time necessary to complete that purpose. 5. Owner agrees to hold the City harmless for any loss or damage to persons or property occurring on the private property during the City's entry upon the property, unless the loss or damage is the result of the sole negligence of the City. 6. Non -responsiveness to a City information request for ninety (90) or more days, shall be cause to cancel the application(s) without refund of fees. EXECUTED at Itasca (city), IL (state), on Wednesday, April 1 1th Drew Parker ,2018 (Print Name) 1351 E. Irving Park Road Itasca IL. 60143 (Address) 630-634-4932 (Phone Number) (Signature) On this day personally appeared before me iZe- W --/ ?A RjER to me known to be the individual who executed the foregoing instrument and acknowledged that he/she signed the same as his/her voluntary act and deed for the uses and purposes mentioned therein. SUBSCRIBED AND SWORN TO BEFORE ME ON THIS / / 771 DAY OF AP gI L, , 20 / OFFICIAL SEAL KENNETH J KWASNIK NOTARY PUBLIC - STATE OF ILLINOIS MY COMMISSION EXPIRES 05/08/21 NOTARY PUBLIC in and+for the State ofiL LJNoLS residing at CQc* / . LO11ntrt My Commission expires on C 0 R/20 2 1 V E D N':\t SHAREPOINT FOLDER RESTRUCTURE+Reference\PPLCAfONS . Lend Use Apps & Hendoui 'CURRENT LAND USE APPLICATIONS\DRAFr Wireless Co ioj�n Fecitiq.docx• V �i 201� . Community DeveIoomPnt April 10, 2018 City of Tukwila Department of Community Development 6300 Southcenter Boulevard, Suite #100 Tukwila, WA 98188 Re: AT&T Wireless Site Number/Name: Site Address: Communication Facility Modification SG19 — Riverton North 3516 South 146th Street Tukwila, WA 98168 6409A COVER LETTER / COMPLIANCE WITH TMC SECTION 18.58 AvI a sTe c Network Solutions Department of Community Development: On behalf of New Cingular Wireless PCS, LLC (dba "AT&T") we are pleased to submit this request to modify AT&T's.existing wireless communication site at the location referenced above. Proposal AT&T proposes to modify an existing unstaffed wireless communication facility. The existing facility is located on a radio tower located at 3516 South 146th Street Tukwila, WA 98168. The proposed modification is depicted below and also show on the accompanying construction drawings. • REMOVE (3) EXISTING PANEL ANTENNAS FROM POSITION 4 (1 PER SECTOR) • REMOVE (3) EXISTING TMAS FROM POSITION 1 (1 PER SECTOR) • RELOCATE (3) EXISTING ANTENNAS FROM POSITION 1 TO POSITION 4 (1 PER SECTOR) • RELOCATE (3) EXISTING RRHS FROM POSITION 4 TO POSITION 1 (1 PER SECTOR) • INSTALL (3) PROPOSED PANEL ANTENNAS IN POSITION 1 (1 PER SECTOR) • INSTALL (3) PROPOSED RRHS IN POSITION 1 (1 PER SECTOR) • INSTALL (3) 4C BCEM CARD • INSTALL (3) CORDEX RECTIFIERS TO POWER PLANT This proposal complies with Tukwila Municipal Code (TMC) Section 18.58 which regulates the placement, construction and modification of wireless communication facilities, in order to protect the health, safety and welfare of the public, while not unreasonably interfering with the development of the competitive wireless telecommunications marketplace in the City. This proposal is not consider a substantial change as defined by the FCC rules or TMC Section 18.58.200. RECEWE MAY 02 2018 Community Development • Page 2 • Scope of Work The proposal qualifies as an Eligible Facilities Request for a minor modification under Section 6409a. A copy of the Federal Commission's 6409a rule is enclosed for your information. AT&T proposes the following minor modifications to this site. (Please note: all work will be performed wholly within the existing premises and utility easements; and the project otherwise complies with the site's original conditions of approval.) Component Federal Section 6409 Limits AT&T's Proposed Modification Increase height of original structure 10 feet or less No increase in height of existing equipment proposed. Antennas extending horizontally from edge of structure 6 feet or less Antennas extend less than 1 foot horizontally from edge of structure. Additional equipment cabinets 4 or fewer, with no cabinets larger than the existing cabinets No additional cabinets proposed. Excavation * Excavation or deployment outside the current site. No excavation proposed for this scope of work. Concealment Proposal would defeat concealment elements of the eligible support structure. Proposal does not defeat concealment elements. FCC Shot Clock for Section 6409a Minor Modifications Based on a submittal intake appointment date/filing date of April 10, 2018, the projected FCC deadline for a decision is June 10, 2018. Our goal is to work with you to obtain approval ofthis minor modification earlier than the deadline. We will respond promptly to any requests for information you may have for our application. Please let us know how we can work with you to expedite the approval process. We look forward to working with you on this important project, which will significantly improve wireless telecommunication services in your community without requiring an additional site. Should you have any questions or require additional information, please do not hesitate to contact me. Sincerely, Drew. ?a -ket- Drew Parker, Zoning & Permitting Specialist 1351 E. Irving Park Road, Itasca, IL 60143 Office: 630-634-4932 Email: Drew.Parker@mastec.com RECEIVED MAY 02 2018 Community Development Know what's below Call before you dig. BUILDING CODE COMPLIANCE ALL WORK AND MATERIALS SHALL BE PERFORMED AND INSTALLED IN ACCORDANCE WITH THE CURRENT CONDITIONS OF THE FOLLOWING CODES AS ADOPTED BY THE LOCAL GOVERNING AUTHORITIES. NOTHING IN THESE PLANS IS TO BE CONSTRUED TO PERMIT WORK NOT CONFORMING TO THESE CODES: WASHINGTON STATE AND LOCAL BUILDING CODES: 2015 INTERNATIONAL BUILDING CODE 2014 NATIONAL ELECTRIC CODE TIA-222—G OR LATEST EDITION PROJECT INFORMATION AT&T PROJECT DESCRIPTION' REMOVE: —(3) EXISTING PANEL ANTENNAS FROM POSITION 4 (1 PER SECTOR) —(3) EXISTING TMAS FROM POSITION 1 (1 PER SECTOR) RELOCATE: —(3) EXISTING PANEL ANTENNAS FROM POSITION 1 TO POSITION 4 (1 PER SECTOR) —(3) EXISTING RRHS FROM POSITION 4 TO POSITION 1 FOR EXISTING L7 (1 PER SECTOR) INSTALL: —(3) PROPOSED PANEL ANTENNAS IN POSITION 1 (1 PER SECTOR) —(3) PROPOSED RRHS IN POSITION 1 FOR WCS (1 PER SECTOR) —(3) 4C BCEM CARD —(3) CORDEX RECTIFIERS TO POWER PLANT PACE #: MRWOR029444/MRWOR029334 PTN #: 3801A0DB79 APPLICANT' EEQ AT&T MOBILITY RFDS V 2.00 11/01/2017 RTC BUILDING 3 16221 NE 72ND WAY PROPERTY OWNER; REDMOND, WA 98052 ARK VIA NELLE, LLC. 18107 NORMANDY TERRACE SW CODE INFORMATION' NORMANDY PARK, WA 98166 PARCEL ID: 004000-0315 ZONING CLASSIFICATION: HDR SITE ACQUISITION• JURISDICTION: CITY OF TUKWILA MASTEC BUILDING CODE: 2015 INTERNATIONAL BUILDING CODE DAN KELLY 22263 68th AVE S, KENT, WA 98032 SITE LOCATION (BASED ON NAD 83)' EMAIL: Doniel.KellyOmostee.eom LATITUDE: 47' 28' 22.61" N (47.472947') OFFICE: (425)214-9749 LONGITUDE: 122' 17' 13.77" W (-122.287158') TOP OF STRUCTURE AGL: ±51.8'-0" CONSTRUCTION MANAGER* BASE OF STRUCTURE ASML: *345.9' MASTEC 1203 114TH AVE SE GFNERAL INFORMATION* BELLEVUE, WA 98004 1. TRAFFIC IS UNAFFECTED. CONTACT: TBD FGAI DESCRIPTION: PERMITTING' ADAMS HOME TRS TBD PLAT BLOCK 2 PLAT LOT 30 AT&T PROJECT MANAGLR; TBD CONTACT INFORMATION ENGINEER: GPD GROUP PROFESSIONAL CORPORATION 400 NORTH 34TH STREET, SUITE 216 AKRON, OH 44311 CONTACT: JAMES GRANT PHONE: (206) 204-7398 • u at&t mobility RIVERTON NORTH SG19 10092691 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LOCAL MAP t mash !times e.sa"a 154th b1 Sam/memo- 81:71 '.4ea ,....,u 8 .10.1 11.11,111 5.14103x Thorndyke Ch Elementary School 4 The Boulevard el South Station Apanmenl Homes 7 souncru. eta - s'm`^.7444, NO SCALE DRIVING DIRECTIONS START FROM SEATTLE—TACOMA INTERNATIONAL AIRPORT: HEAD SOUTHEAST ON AIRPORT EXPRESSWAY TOWARD DEPARTURES DR (56 FT). USE THE LEFT LANE TO KEEP LEFT (0.1 MI). KEEP LEFT(0.5 MI). CONTINUE ON AIRPORT EXPRESSWAY. DRIVE FROM WA-518 E AND 51ST AVE S TO TUKWILA (3.0 MI). SLIGHT LEFT ONTO AIRPORT EXPRESSWAY(0.8 MI). KEEP RIGHT AT THE FORK, FOLLOW SIGNS FOR WA-518 E/INTERSTATE 5/INTERSTATE 405 AND MERGE ONTO WA-518 E (1.3 MI). TAKE THE 51ST AVENUE S EXIT TOWARD SOUTHCENTER PKWY (0.2 MI). TURN LEFT ONTO 51ST AVE S (0.7 MI). TAKE S 144TH ST TO 42ND AVE S (0.5 MI). TURN LEFT TOWARD S 144TH ST (302 FT). TURN LEFT ONTO S 144TH ST (0.5 MI). TURN LEFT ONTO 42ND AVE S (0.1 MI). TURN RIGHT AT THE 1ST CROSS STREET ONTO S 146TH ST. DESTINATION WILL BE ON THE RIGHT (0.3 MI). ARRIVED AT 3516 S 146TH ST. PROPRIETARY INFORMATION THE INFORMATION CONTAINED IN THIS SET OF CONSTRUCTION DOCUMENTS IS PROPRIETARY BY NATURE. ANY USE OR DISCLOSURE OTHER THAN THAT WHICH RELATES TO CARRIER SERVICES IS STRICTLY PROHIBITED. DRAWING INDEX SHEET NO: SHEET TITLE T-1 TITLE SHEET GN-1 LEGENDS, ABBREVIATIONS & CONSTRUCTION INSPECTIONS GN-2 GENERAL NOTES C-1 OVERALL SITE PLAN C-2 COMPOUND PLAN & EQUIPMENT LAYOUT C-3 TOWER ELEVATION & NOTES RF-1 EXISTING ANTENNA CONFIGURATION RF-1.2 PROPOSED ANTENNA CONFIGURATION RF-2 ANTENNA & RRH DETAILS RF-3 SIGNAGE DETAILS E-1 GROUNDING DETAILS E-2 ELECTRICAL NOTES APPROVAL DATE SIGNATURE APPROVAL DATE SIGNATURE RF ENGINEER: LANDLORD: RF MANAGER: SITE ACQUISITION: OPPS MANAGER: ZONING AGENT: CONSTR. MANAGER: PROJECT MANAGER: NSB MANAGER: CONSTR. MANAGER: TRANSPORT: EQUIP. ENGINEER: COMPLIANCE: REVIEWERS SHALL CLEARLY PLACE INITIALS ADJACENT TO EACH REDONE NOTE AS DRAWINGS ARE BEING REVIEWED 1111x1711 PLOT WILL BE HALF SCALE UNLESS OTHERWISE NOTED n GENERAL NOTES a..WW THE FACILITY IS UNMANNED AND NOT FOR HUMAN HABITATION. A TECHNICIAN WILL VISIT THE sue` se' SITE AS REOUIRED FOR ROUTINE MAINTENANCE. THE PROJECT WILL NOT RESULT IN ANY w SIGNIFICANT DISTURBANCE OR EFFECT ON DRAINAGE; NO SANITARY SEWER SERVICE, POTABLE � g WATER, OR TRASH DISPOSAL IS REOUIRED AND NO COMMERCIAL SIGNAGE IS PROPOSED. Li CONTRACTOR SHALL VERIFY ALL PLANS & EXISTING DIMENSIONS & CONDITIONS ON Lu THE JOB SITE & SHALL IMMEDIATELY NOTIFY THE ENGINEER IN WRITING OF ANY DISCREPANCIES BEFORE PROCEEDING WITH THE WORK OR BE RESPONSIBLE FOR SAME 17: `....� at&t mobility -IasTec Network Solutions GPD GROUP Professional Corporation 520 South Hain Street, Suite 2531 AVON, OH 44311 330.572.2100 Fax: 330.572.2102 PROJECT 140: 2018723.04.25588.01 DRAWN BY: AGL CHECKED BY: JG 1 04/25/18 REVISED PER CUENT COMMENTS 0 4/5/18 ISSUED FOR CONSTRUCTION A r l REVIEW PIRES 04/16/2020 IT IS A VIOLATION OF LAW FOR ANY PERSON. UNLESS THEY ARE ACTING UNDER INC DIRECTION OF A LICENSED PROFESSIONAL ENGINEER. TO ALTER THIS DOCUMENT. J 1 RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE— ROOFTOP N E SHEET TITLE TITLE SHEET E 0) U a) a T-1 SHEET NUMBER EXOTHERMIC CONNECTION • MECHANICAL CONNECTION ■ CHEMICAL ELECTROLYTIC GROUNDING SYSTEM 0 TEST CHEMICAL ELECTROLYTIC GROUNDING SYSTEM e T EXOTHERMIC WITH INSPECTION SLEEVE ❑• AB AN:OLT INT INTERIOR ABV ABO LB(S) POUND(S) AC ALTERNATING CURRENT LF LINEAR FEET ADDL ADDITIONAL MAS MASONRY AFF ABOVE FINISHED FLOOR MAX MAXIMUM AIC AMPS GE INED GRADE MB MACHINE AOLT AIC AMPERAGE INTERRUPTION CAPACITY MACH MECHANICAL ALUM ALUMINUM MFR MANUFACTURER ALT ALTERNATE MGB MASTER GROUND BAR ANT ANTENNA MIN MINIMUM APPROX APPROXIMATE MISC MISCELLANEOUS ARCH ARCHITECTURAL MTL METAL ATS AUTOMATIC TRANSFER SWITCH MiS MANUAL TRANSFER SWITCH AWG AMERICAN WIRE GAUGE MW MICROWAVE BATT BATTERY (N) NEW BLDG BUILDING NEC NATIONAL ELECTRIC CODE BLK BLOCK NO.(#) NUMBER BLKG BLOCKING NTS NOT TO SCALE BM BEAM OC ON CENTER BTC BARE TINNED COPPER CONDUCTOR OPNG OPENING BOF BOTTOM OF FOOTING CAB CABINET (P) PROPOSED P/C PRECAST CONCRETE CANT CANTILEVERED CEC CALIFORNIA ELECTRIC CODE PCS PERSONAL COMMUNICATION SERVICES CHG CHARGING PCU PRIMARY CONTROL UNIT CLG CEILING • PRC PRIMARY RADIO CABINET CLR CLEAR PP POLARIZING PRESERVING COL COLUMN PSF POUNDS PER SQUARE FOOT COMM COMMON PSI POUNDS PER SQUARE INCH PT PRESSURE TREATED CONC CONCRETE CONSTR CONSTRUCTION PWR POWER CABINET DBL DOUBLE OTY QUANTITY DC DIRECT CURRENT RAD RADIUS DEPT DEPARTMENT RECT RECTIFIER DF DOUGLAS FIR REF REFERENCE DIA DIAMETER REINF REINFORCEMENT DIAG DIAGONAL REO'D REQUIRED DIM DIMENSION RET REMOTE ELECTRIC TILT DWG DRAWING RMC RIGID METALLIC CONDUIT DWL DOWEL RRH REMOTE RADIO HEAD (E) EXISTING RRU REMOTE RADIO UNIT RWY EA EACH SCH RACEWAY EC ELECTRICAL CONDUCTORCH SCHEDULE EL ELEVATION SHT SHEET ELEC ELECTRICAL SIAD SMART INTEGRATED DEVICEEMT ELECTRICAL METALLIC TUBINGSIM SIMILAR('\iOOA ENG ENGINEER SPEC SPECIFICATION EO EQUALSO SQUARE EXP EXPANSION SS STAINLESS STEEL EXT EXTERIOR STD STANDARD FAB FABRICATION STL STEEL STRUCT STRUCTURAL FF FINISH FLOOR FG FINISH GRADE TEMP TEMPORARY FIF FACILITY INTERFACE FRAME THK THICKNESS,a TMA TOWER MOUNTED AMPLIFIER FIN FINISH(ED) FLIT FLOOR TN TOE NAIL FDN FOUNDATION TOA TOP OF ANTENNA FOC FACE OF CONCRETE TOC TOP OF CURB FOM FACE OF MASONRY TOF TOP OF FOUNDATION FOS FACE OF STUD TOP TOP OF PLATE (PARAPET) FOW FACE OF WALL TOS TOP OF STEEL FS FINISH SURFACE TOW TOP OF WALL FT FOOT TVSS TRANSIENT VOLTAGE SUPPRESSION SYSTEM FTG . FOOTING TYP TYPICAL GA GAUGE UG UNDERGROUND GEN GENERATOR UL UNDERWRITERS LABORATORY GFCI GROUND FAULT CIRCUIT INTERRUPTER LINO UNLESS NOTED OTHERWISE GLB GLUE LAMINATED BEAM UMTS UNIVERSAL MOBILE TELECOMMUNICATIONS GLV GALVANIZED SYSTEM GPS GLOBAL POSITIONING SYSTEM • UPS UNITERRUPTIBLE POWER STSIEM GND GROUND (DC POWER PLANT) GSM GLOBAL SYSTEM FOR MOBILE VIF VERIFIED IN FIELD HDR HEADER W WIDE HGR HANGER W/ WITH HVAC HEAT/VENTILATION/AIR CONDITIONING WD WOOD HT HEIGHT W.P. WORK POINT IGR INTERIOR GROUND RING WP WEATHERPROOF IN ' INCH WT WEIGHT MAY 022O8 Community Development „agl.F14 r 42!!!!!!!!!:::: `�®`�// J a t&t mobility GROUNDING BAR GROUND ROD III TEST GROUND ROD WITH INSPECTION SLEEVE OF -ET SINGLE POLE SWITCH y.L� DUPLEX RECEPTACLE /11� ��uf�fJ DUPLEX GFCI RECEPTACLE FLUORESCENT LIGHTING FIXTURE r (2) TWO LAMPS 48-TB L SMOKE DETECTION (DC) I �J 1 F 3 SD --I ■1 a S Network Solutions t `/� e c • IMMI A. GPD GROUP Professional Corporation 520 South Hain Street, Suite 2531 4311 AC 330.572.21027 330.572.2100 Fax: EMERGENCY LIGHTING (DC) 8 E SECURITY LIGHT W/PHOTOCELL LITHONIA ALXW LED-1 -25A400/51 K -SR4 - 1 20 - PE- DDBTXD CHAINLINK FENCE —•—•—•—•—•—•—•—•—•— FENCE - o - o o WOOD/WROUGHT IRON o 0 0 o PROJECT NO: 2018723.04.25588.011 WALL STRUCTURE I'//////////////////////////////////� LEASE AREA PROPERTY LINE (PL)---------------------- SETBACKS - DRAWN BY: AGL CHECKED BY: JG ♦ ICE BRIDGE aoranAAAnvanwAAAAAAvAAAAvAnewAniAAivierAvAAy rAvAvAvAvAvAvAvA•••••••0•••AvAvAvAYAYAYAvAvAvAvAvAvAvAvAvAvAvAvA CABLETRAY ............................... WATER LINE - • — • — • — • — • — . — • — • — • — • - 1 04/25/18 REVISED PER CLIENT COMMENTS o 4/5/18 ISSUED FOR CONSTRUCTION UNDERGROUND POWER ` A ',.s 'wt ?:2M ,' FOR REVIEW i UNDERGROUND TELCO UP PP PC PC OR — UP UP OVERHEAD POWER—w—o.—n.—e.—..—..—w— `\^S//OVERHEAD Al.,r'�'jO e. OF /tUNDERGROUND 'V l`� -' � � : , C,: V'!� r`.-+"_ 4' .00 55771 ,p RrC'141Y1i4- ^ )A'' P>. FS r0 , ., 1• L�,.��(��jA1.: `';..r' ., O A ' �� +r ,,' r /26/ 1 O TELCO as '" '• - — Oa °° — TELCO/POWER-w•n-wVn-MVP-uo�n-Wn-�v.-..v.-wv.-wv.- ABOVE GROUND POWER-•�-p-b-p--•o-•�-•�-p-p-p- -----•0f•0f-•0f-�-�-� ABOVE GROUND TELCO _ ABOVE GROUND TELCO/POWER -"01p —"0f7' —"01A — AMP —"017' —./.. —1.,/, —1QV' — "0f7' — WORKPOINT W.P. / SECTION REFERENCE GO ® .-, VIRES 04/16/2029 I CE DETAIL REFERENCE ® IT IS A VIOLATION OF LAW FOR ANY PERSON. UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A UCENSED PROFESSIONAL ENGINEER. TO ALTER THIS DOCUMENT. • RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE- ROOFTOP i - - • SHEET TITLE LEGENDS, ABBREVIATIONS & CONSTRUCTION INSPECTIONS SHEET NUMBER GN-1 LEGEND 1 ABBREVIATIONS I 2 NOT USED 3 1 GFNFRAL CONSTRUCTION 1. FOR THE PURPOSE OF CONSTRUCTION DRAWINGS, THE FOLLO , EFINITIONS SHALL APPLY: GENERAL CONTRACTOR - MASTEC CONTRACTOR: (CONSTRUCTION) OWNER - AT&T ENGINEER - GPD GROUP 2. ALL SITE WORK SHALL BE COMPLETED AS INDICATED ON THE DRAWINGS AND AT&T PROJECT SPECIFICATIONS. 3. GENERAL CONTRACTOR SHALL VISIT THE SITE AND SHALL FAMILIARIZE HIMSELF WITH ALL CONDITIONS AFFECTING THE PROPOSED WORK AND SHALL MAKE PROVISIONS. GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR FAMILIARIZING HIMSELF WITH ALL CONTRACT DOCUMENTS, FIELD CONDITIONS, DIMENSIONS, AND CONFIRMING THAT THE WORK MAY BE ACCOMPLISHED AS SHOWN PRIOR TO PROCEEDING WITH CONSTRUCTION. ANY DISCREPANCIES SHALL BE BROUGHT TO THE ATTENTION OF THE ENGINEER PRIOR TO THE COMMENCEMENT OF WORK. 4. ALL MATERIALS FURNISHED AND INSTALLED SHALL BE IN STRICT ACCORDANCE WITH ALL APPLICABLE CODES, REGULATIONS. AND ORDINANCES. GENERAL CONTRACTOR SHALL ISSUE ALL APPROPRIATE NOTICES AND COMPLY WITH ALL LAWS, ORDINANCES, RULES. REGULATIONS. AND LAWFUL ORDERS OF ANY PUBLIC AUTHORITY REGARDING THE PERFORMANCE OF WORK. 5. ALL WORK CARRIED OUT SHALL COMPLY WITH ALL APPLICABLE MUNICIPAL AND UTILITY COMPANY SPECIFICATIONS AND LOCAL JURISDICTIONAL CODES, ORDINANCES, AND APPLICABLE REGULATIONS. 6. UNLESS NOTED OTHERWISE, THE WORK SHALL INCLUDE FURNISHING MATERIALS, EQUIPMENT, APPURTENANCES. AND LABOR NECESSARY TO COMPLETE ALL INSTALLATIONS AS INDICATED ON THE DRAWINGS. 7. PLANS ARE NOT TO BE SCALED. THESE PLANS ARE INTENDED TO BE A DIAGRAMMATIC OUTLINE ONLY UNLESS OTHERWISE NOTED. DIMENSIONS SHOWN ARE TO FINISH SURFACES UNLESS OTHERWISE NOTED. SPACING BETWEEN EQUIPMENT IS THE MINIMUM REQUIRED CLEARANCE. THEREFORE, IT IS CRITICAL TO FIELD VERIFY DIMENSIONS, SHOULD THERE BE ANY OUESTIONS REGARDING THE CONTRACT DOCUMENTS. THE CONTRACTOR SHALL BE RESPONSIBLE FOR OBTAINING A CLARIFICATION FROM THE ENGINEER PRIOR TO PROCEEDING WITH THE WORK. DETAILS ARE INTENDED TO SHOW DESIGN INTENT. MODIFICATIONS MAY BE REOUIRED TO SUR JOB DIMENSIONS OR CONDITIONS AND SUCH MODIFICATIONS SHALL BE INCLUDED AS PART OF WORK AND PREPARED BY THE ENGINEER PRIOR TO PROCEEDING WITH WORK. 8. THE CONTRACTOR SHALL INSTALL ALL EQUIPMENT AND MATERIALS IN ACCORDANCE WITH MANUFACTURER'S RECOMMENDATIONS UNLESS SPECIFICALLY STATED OTHERWISE. 9. IF THE SPECIFIED EQUIPMENT CANNOT BE INSTALLED AS SHOWN ON THESE DRAWINGS. THE CONTRACTOR SHALL PROPOSE AN ALTERNATIVE INSTALLATION SPACE FOR APPROVAL BY THE ENGINEER PRIOR TO PROCEEDING. 10. GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR THE SAFETY OF WORK AREA. ADJACENT AREAS AND BUILDING OCCUPANTS THAT ARE LIKELY TO BE AFFECTED BY THE WORK UNDER THIS CONTRACT. WORK SHALL CONFIRM TO ALL OSHA REQUIREMENTS AND THE LOCAL JURISDICTION. 11. GENERAL CONTRACTOR SHALL COORDINATE WORK AND SCHEDULE WORK ACTIVITIES WITH OTHER DISCIPLINES. 12. ERECTION SHALL BE DONE IN A WORKMANLIKE MANNER BY COMPETENT EXPERIENCED WORKMAN IN ACCORDANCE WITH APPLICABLE CODES AND THE BEST ACCEPTED PRACTICE. ALL MEMBERS SHALL BE LAID PLUMB AND TRUE AS INDICATED ON THE DRAWINGS. 13. SEAL PENETRATIONS THROUGH FIRE RATED AREAS WITH UL LISTED MATERIALS APPROVED BY LOCAL JURISDICTION. CONTRACTOR SHALL KEEP AREA CLEAN. HAZARD FREE. AND DISPOSE OF ALL DEBRIS. 14. WORK PREVIOUSLY COMPLETED IS REPRESENTED BY LIGHT SHADED LINES AND NOTES. THE SCOPE OF WORK FOR THIS PROJECT IS REPRESENTED BY DARK SHADED LINES AND NOTES. CONTRACTOR SHALL NOTIFY THE GENERAL CONTRACTOR OF ANY EXISTING CONDITIONS THAT DEVIATE FROM THE DRAWINGS PRIOR TO BEGINNING CONSTRUCTION. 15. CONTRACTOR SHALL PROVIDE WRITTEN NOTICE TO THE CONSTRUCTION MANAGER 48 HOURS PRIOR TO COMMENCEMENT OF WORK. 16. THE CONTRACTOR SHALL PROTECT EXISTING IMPROVEMENTS. PAVEMENTS, CURBS, LANDSCAPING AND STRUCTURES. ANY DAMAGED PART SHALL BE REPAIRED AT CONTRACTOR'S EXPENSE TO THE SATISFACTION OF THE OWNER. 17. THE CONTRACTOR SHALL CONTACT UTILITY LOCATING SERVICES PRIOR TO THE START OF CONSTRUCTION. 18. GENERAL CONTRACTOR SHALL COORDINATE AND MAINTAIN ACCESS FOR ALL TRADES AND CONTRACTORS TO THE SITE AND/OR BUILDING. 19. THE GENERAL CONTRACTOR SHALL BE RESPONSIBLE FOR SECURITY OF THE SITE FOR THE DURATION OF CONSTRUCTION UNTIL JOB COMPLETION. 20. THE GENERAL CONTRACTOR SHALL MAINTAIN IN GOOD CONDITION ONE COMPLETE SET OF PLANS WITH ALL REVISIONS, ADDENDA AND CHANGE ORDERS ON THE PREMISES AT ALL TIMES. 21. THE GENERAL CONTRACTOR SHALL PROVIDE PORTABLE FIRE EXTINGUISHERS WITH A RATING OF NOT LESS THAN 2-A OT 2-A:10-B:C AND SHALL BE WITHIN 25 FEET OF TRAVEL DISTANCE TO ALL PORTIONS OF WHERE THE WORK IS BEING COMPLETED DURING CONSTRUCTION. 22. ALL EXISTING ACTIVE SEWER. WATER. GAS, ELECTRIC, AND OTHER UTILITIES SHALL BE PROTECTED AT ALL TIMES, AND WHERE REQUIRED FOR THE PROPER EXECUTION OF THE WORK, SHALL BE RELOCATED AS DIRECTED BY THE ENGINEER. EXTREME CAUTION SHOULD BE USED BY THE CONTRACTOR WHEN EXCAVATING OR DRILLING PIERS AROUND OR NEAR UTILITIES. CONTRACTOR SHALL PROVIDE SAFETY TRAINING FOR THE WORKING CREW. THIS SHALL INCLUDE BUT NOT BE LIMITED TO A) FALL PROTECTION, B) CONFINED SPACE. C) ELECTRICAL SAFETY, AND D) TRENCHING & EXCAVATION. 23. ALL EXISTING INACTIVE SEWER, WATER, GAS. ELECTRIC, AND OTHER UTILITIES, WHICH INTERFERE WITH THE EXECUTION OF THE WORK. SHALL BE REMOVED, CAPPED, PLUGGED OR OTHERWISE DISCONNECTED AT POINTS WHICH WILL NOT INTERFERE WITH THE EXECUTION OF THE WORK, AS DIRECTED BY THE RESPONSIBLE ENGINEER. AND SUBJECT TO THE APPROVAL OF THE OWNER AND/OR LOCAL UTILITIES. 24. THE AREAS OF THE OWNER'S PROPERTY DISTURBED BY THE WORK AND NOT COVERED BY THE TOWER, EQUIPMENT OR DRIVEWAY, SHALL BE GRADED TO A UNIFORM SLOPE. AND STABILIZED TO PREVENT EROSION. 25. CONTRACTOR SHALL MINIMIZE DISTURBANCE TO THE EXISTING SITE DURING CONSTRUCTION. EROSION CONTROL MEASURES, IF REQUIRED DURING CONSTRUCTION. SHALL BE IN CONFORMANCE WITH THE FEDERAL AND LOCAL JURISDICTION FOR EROSION AND SEDIMENT CONTROL 26. NO FILL OR EMBANKMENT MATERIAL SHALL BE PLACED ON FROZEN GROUNDING. FROZEN MATERIALS, SNOW OR ICE SHALL NOT BE PLACED IN ANY FILL OR EMBANKMENT. 27. THE SUBGRADE SHALL BE BROUGHT TO A SMOOTH UNIFORM GRADE AND COMPACTED TO 95 PERCENT STANDARD PROCTOR DENSITY UNDER PAVEMENT AND STRUCTURES AND 80 PERCENT STANDARD PROCTOR DENSITY IN OPEN SPACE. ALL TRENCHES IN PUBLIC RIGHT OF WAY SHALL BE BACKFILLED WITH FLOWABLE FILL OR OTHER MATERIAL PRE -APPROVED BY THE LOCAL JURISDICTION. 28. ALL NECESSARY RUBBISH, STUMPS. DEBRIS, STICKS. STONES. AND OTHER REFUSE SHALL BE REMOVED FROM THE SITE AND DISPOSED OF IN A LAWFUL MANNER. 29. ALL BROCHURES. OPERATING AND MAINTENANCE MANUALS. CATALOGS. SHOP DRAWINGS. AND OTHER DOCUMENTS SHALL BE TURNED OVER TO THE GENERAL CONTRACTOR AT COMPLETION OF CONSTRUCTION AND PRIOR TO PAYMENT. 31. CONTRACL LEAVE PREMISES IN A CLEAN CONDITION. 32. THE PROPOSED FACILITY WILL BE UNMANNED AND DOES NOT REOUIRE POTABLE WATER OR SEWER SERVICE, AND IS NOT FOR HUMAN HABITAT (NO HANDICAP ACCESS REQUIRED). 33. OCCUPANCY IS LIMITED TO PERIODIC MAINTENANCE AND INSPECTION. APPROXIMATELY 2 TIMES PER MONTH, BY AT&T TECHNICIANS. 34. NO OUTDOOR STORAGE OR SOLID WASTE CONTAINERS ARE PROPOSED. 35. ALL MATERIAL SHALL BE FURNISHED AND WORK SHALL BE PERFORMED IN ACCORDANCE WITH THE LATEST REVISION AT&T MOBILITY GROUNDING STANDARD "TECHNICAL SPECIFICATION FOR CONSTRUCTION OF GSM/GPRS WIRELESS SITES" AND 'TECHNICAL SPECIFICATION FOR FACILITY GROUNDING". IN CASE OF A CONFLICT BETWEEN THE CONSTRUCTION SPECIFICATION AND THE DRAWINGS, THE DRAWINGS SHALL GOVERN. 36. CONTRACTORS SHALL BE RESPONSIBLE FOR OBTAINING ALL PERMITS AND INSPECTIONS REQUIRED FOR CONSTRUCTION. IF CONTRACTOR CANNOT OBTAIN A PERMIT. THEY MUST NOTIFY THE GENERAL CONTRACTOR IMMEDIATELY. 37. CONTRACTOR SHALL REMOVE ALL TRASH AND DEBRIS FROM THE SITE ON A DAILY BASIS. 38. INFORMATION SHOWN ON THESE DRAWINGS WAS OBTAINED FROM SITE VISITS AND/OR DRAWINGS PROVIDED BY THE SITE OWNER. CONTRACTORS SHALL NOTIFY THE ENGINEER OF ANY DISCREPANCIES PRIOR TO ORDERING MATERIAL OR PROCEEDING WITH CONSTRUCTION. 39. NO WHITE STROBE LIGHTS ARE PERMITTED. LIGHTING IF REQUIRED. WILL MEET FM STANDARDS AND REQUIREMENTS. 40. ALL COAXIAL CABLE INSTALLATIONS TO FOLLOW MANUFACTURER'S INSTRUCTIONS AND RECOMMENDATIONS. ANTENNA MOUNTING 41. DESIGN AND CONSTRUCTION OF ANTENNA SUPPORTS SHALL CONFORM TO CURRENT ANSI/TIA-222 OR APPLICABLE LOCAL CODES. 42. ALL STEEL MATERIALS SHALL BE GALVANIZED AFTER FABRICATION IN ACCORDANCE WITH ASTM A123 "ZINC (HOT -DIP GALVANIZED) COATINGS ON IRON AND STEEL PRODUCTS', UNLESS NOTED OTHERWISE. 43. ALL BOLTS, ANCHORS AND MISCELLANEOUS HARDWARE SHALL BE GALVANIZED IN ACCORDANCE WITH ASTM A153 "ZINC -COATING (HOT -DIP) ON IRON AND STEEL HARDWARE UNLESS NOTED OTHERWISE. 44. DAMAGED GALVANIZED SURFACES SHALL BE REPAIRED BY COLD GALVANIZING IN ACCORDANCE WITH ASTM A780. 45. ALL ANTENNA MOUNTS SHALL BE INSTALLED WITH LOCK NUTS, DOUBLE NUTS AND SHALL BE TORQUED TO MANUFACTURER'S RECOMMENDATIONS. 46. CONTRACTOR SHALL INSTALL ANTENNA PER MANUFACTURER'S RECOMMENDATION FOR INSTALLATION AND GROUNDING. 47. ALL UNUSED PORTS ON ANY ANTENNAS SHALL BE TERMINATED WITH A 50-OHM LOAD TO ENSURE ANTENNAS PERFORM AS DESIGNED. 48. PRIOR TO SETTING ANTENNA AZIMUTHS AND DOWNTILTS, ANTENNA CONTRACTOR SHALL CHECK THE ANTENNA MOUNT FOR TIGHTNESS AND ENSURE THAT THEY ARE PLUMB. ANTENNA AZIMUTHS SHALL BE SET FROM TRUE NORTH AND BE ORIENTED WITHIN +/- 5% AS DEFINED BY THE RFDS. ANTENNA DOWNTILTS SHALL BE WITHIN +/- 0.5% AS DEFINED BY THE RFDS. REFER TO ND-00246. 49. JUMPERS FROM THE TMA'S MUST TERMINATE TO OPPOSITE POLARIZATION'S IN EACH SECTOR. 50. CONTRACTOR SHALL RECORD THE SERIAL #. SECTOR. AND POSITION OF EACH ACTUATOR INSTALLED AT THE ANTENNAS AND PROVIDE THE INFORMATION TO AT&T. 51. TMA'S SHALL BE MOUNTED ON PIPE DIRECTLY BEHIND ANTENNAS AS CLOSE TO ANTENNA AS FEASIBLE IN A VERTICAL POSITION. 52. ANTENNAS SHALL HAVE A 4'-0" MIN CENTER TO CENTER HORIZONTAL SEPARATION. TOROUE REQUIREMENTS 53. ALL RF CONNECTIONS SHALL BE TIGHTENED BY A TOROUE WRENCH. 54. ALL RF CONNECTIONS. GROUNDING HARDWARE AND ANTENNA HARDWARE SHALL HAVE A TORQUE MARK INSTALLED IN A CONTINUOUS STRAIGHT LINE FROM. BOTH SIDES OF THE CONNECTION. A. RF CONNECTION BOTH SIDES OF THE CONNECTOR. B. GROUNDING AND ANTENNA HARDWARE ON THE NUT SIDE STARTING FROM THE THREADS TO THE SOLID SURFACE. EXAMPLE OF SOLID SURFACE: GROUND BAR, ANTENNA BRACKET METAL. 55. ALL 8M ANTENNA HARDWARE SHALL BE TIGHTENED TO 9 LB -FT (12 NM). 56. ALL 12M ANTENNA HARDWARE SHALL BE TIGHTENED TO 43 LB -FT (58 NM). 57. ALL GROUNDING HARDWARE SHALL BE TIGHTENED UNTIL THE LOCK WASHER COLLAPSES AND THE GROUNDING HARDWARE IS NO LONGER LOOSE. 58. ALL DIN TYPE CONNECTIONS SHALL BE TIGHTENED TO 18-22 LB -FT (24.4 - 29.8 NM). 59. ALL N TYPE CONNECTIONS SHALL BE TIGHTENED TO 15-20 LB -IN (1.7 - 2.3 NM). FIBER & POWER CABLE MOUNTING 60. THE FIBER OPTIC TRUNK CABLES SHALL BE INSTALLED INTO CONDUITS, CHANNEL CABLE TRAYS, OR CABLE TRAY. WHEN INSTALLING FIBER OPTIC TRUNK CABLES INTO A CABLE TRAY SYSTEM, THEY SHALL BE INSTALLED INTO AN INTER DUCT AND A PARTITION BARRIER SHALL BE INSTALLED BETWEEN THE 600 VOLT CABLES AND THE INTER DUCT IN ORDER TO SEGREGATE CABLE TYPES. OPTIC FIBER TRUNK CABLES SHALL HAVE APPROVED CABLE RESTRAINTS EVERY (60) SIXTY FEET AND SECURELY FASTENED TO THE CABLE TRAY SYSTEM. NFPA 70 (NEC) ARTICLE 770 RULES SHALL APPLY. 61. THE TYPE TC-ER CABLES SHALL BE INSTALLED INTO CONDUITS, CHANNEL CABLE TRAYS, OR CABLE TRAY AND SHALL BE SECURED AT INTERVALS NOT EXCEEDING (6) SIX FEET. AN EXCEPTION; WHERE TYPE TC-ER CABLES ARE NOT SUBJECT TO PHYSICAL DAMAGE. CABLES SHALL BE PERMITTED TO MAKE A TRANSITION BETWEEN CONDUITS. CHANNEL CABLE TRAYS. OR CABLE TRAY WHICH ARE SERVING UTILIZATION EQUIPMENT OR DEVICES. A DISTANCE (6) SIX FEET SHALL NOT BE EXCEEDED WITHOUT CONTINUOUS SUPPORTING. NFPA 70 (NEC) ARTICLES 336 AND 392 RULES SHALL APPLY. 62. WHEN INSTALLING OPTIC FIBER TRUNK CABLES OR TYPE TC-ER CABLES INTO CONDUITS. NFPA 70 (NEC) ARTICLE 300 RULES SHALL APPLY. COAXIAL CARI F NOTES 63. TYPES AND SIZES OF THE ANTENNA CABLE ARE BASED ON ESTIMATED LENGTHS. PRIOR TO ORDERING CABLE. CONTRACTOR SHALL VERIFY ACTUAL LENGTH BASED ON CONSTRUCTION LAYOUT AND NOTIFY THE PROJECT MANAGER IF ACTUAL LENGTHS EXCEED ESTIMATED LENGTHS. 62. CONTRACTOR SHALL VERIFY THE DOWN -TILT OF EACH ANTENNA WITH A DIGITAL LEVEL. 63. CONTRACTOR SHALL CONFIRM COAX COLOR CODING PRIOR TO CONSTRUCTION. REFER TO "ANTENNA SYSTEM LABELING STANDARD" ND-00027 LATEST VERSION. 64. ALL JUMPERS TO THE ANTENNAS FROM THE MAIN TRANSMISSION LINE SHALL BE 1/2" DIA LDF AND SHALL NOT EXCEED 6'-0". 65. ALL COAXIAL CABLE SHALL BE SECURED TO THE DESIGNED SUPPORT STRUCTURE, IN AN APPROVED MANNER. AT DISTANCES NOT TO EXCEED 4'-0" OC. 66. CONTRACTOR SHALL FOLLOW ALL MANUFACTURER'S RECOMMENDATIONS REGARDING BOTH THE INSTALLATION AND GROUNDING OF ALL COAXIAL CABLES, CONNECTORS, ANTENNAS, AND ALL OTHER EOUIPMENT. 67. CONTRACTOR SHALL WEATHERPROOF ALL ANTENNA CONNECTORS WITH SELF AMALGAMATING TAPE. WEATHERPROOFING SHALL BE COMPLETED IN STRICT ACCORDANCE WITH AT&T STANDARDS. GENERAL CABLE AND EQUIPMENT NOTES 68. CONTRACTOR SHALL BE RESPONSIBLE TO VERIFY ANTENNA, TMAS, DIPLEXERS, AND COAX CONFIGURATION, MAKE AND MODELS PRIOR TO INSTALLATION. 69. ALL CONNECTIONS FOR HANGERS, SUPPORTS, BRACING, ETC. SHALL BE INSTALLED PER TOWER MANUFACTURER'S RECOMMENDATIONS. 70. CONTRACTOR SHALL REFERENCE THE TOWER STRUCTURAL ANALYSIS/DESIGN DRAWINGS FOR DIRECTIONS ON CABLE DISTRIBUTION/ROUTING. 71. ALL OUTDOOR RF CONNECTORS/CONNECTIONS SHALL BE WEATHERPROOFED. EXCEPT THE RET CONNECTORS, USING BUTYL TAPE AFTER INSTALLATION AND FINAL CONNECTIONS ARE MADE. BUTYL TAPE SHALL HAVE A MINIMUM OF ONE-HALF TAPE WIDTH OVERLAP ON EACH TURN AND EACH LAYER SHALL BE WRAPPED THREE TIMES. WEATHERPROOFING SHALL BE SMOOTH WITHOUT BUCKLING. BUTYL BLEEDING IS NOT ALLOWED. 72. IF REOUIRED TO PAINT ANTENNAS AND/OR COAX: A. TEMPERATURE SHALL BE ABOVE 50' F. B. PAINT COLOR MUST BE APPROVED BY BUILDING OWNER/LANDLORD. C. FOR REGULATED TOWERS, FAA/FCC APPROVED PAINT IS REQUIRED. D. DO NOT PAINT OVER COLOR CODING OR ON EQUIPMENT MODEL NUMBERS. 73. ALL CABLES SHALL BE GROUNDED WITH COAXIAL CABLE GROUND KITS. FOLLOW THE MANUFACTURER'S RECOMMENDATIONS. A. GROUNDING AT THE ANTENNA LEVEL. B. GROUNDING AT MID LEVEL, TOWERS WHICH ARE OVER 200'-0", ADDITIONAL CABLE GROUNDING REQUIRED. C. GROUNDING AT BASE OF TOWER PRIOR TO TURNING HORIZONTAL. D. GROUNDING OUTSIDE THE EQUIPMENT SHELTER AT ENTRY PORT. E. GROUNDING INSIDE THE EOUIPMENT SHELTER AT THE ENTRY PORT. 74. ALL PROPOSED GROUND BAR DOWNLEADS ARE TO BE TERMINATED TO THE EXISTING ADJACENT GROUND BAR DOWNLEADS A MINIMUM DISTANCE OF 4'-0" BELOW GROUND BAR. TERMINATIONS MAY BE EXOTHERMIC OR COMPRESSION. 75. THE CONTRACTOR SHALL BE RESPONSIBLE FOR VERIFYING THE ANTENNA AND THE COAX CONFIGURATION IS THE CORRECT MAKE AND MODELS, PRIOR TO INSTALLATION. 76. ALL CONNECTIONS FOR HANGERS. SUPPORTS, BRACING. ETC. SHALL BE INSTALLED PER TOWER MANUFACTURER'S SPECIFICATION & RECOMMENDATIONS. 77. ANTENNA CONTRACTOR SHALL FURNISH AND INSTALL A 12'-0" T-BOOM SECTOR ANTENNA MOUNT. IF APPLICABLE. INCLUDING ALL HARDWARE. SAFETY ENFORCEMENT SAFETY IS OF PARAMOUNT CONCERN TO BOTH SITE WORKERS AND THE PUBUC. 1. CONSTRUCTION WORK PRESENTS UNIQUE THREATS TO HEALTH AND SAFETY. THE CONTRACTOR IS RESPONSIBLE TO EDUCATE THEIR WORK FORCE OF THESE DANGERS AND LIMIT THEIR EXPOSURE TO HAZARDS. THIS EDUCATION SHALL INCLUDE BUT NOT BE LIMITED TO APPLICABLE TRAINING COURSES AND CERTIFICATIONS, PROPER PERSONAL PROTECTIVE EQUIPMENT USAGE, DAILY TAILGATE MEETINGS AND ANY OTHER PREVENTATIVE MEASURES WHICH MAY BE REASONABLY EXPECTED. THE CONTRACTOR AND ALL SUB -CONTRACTORS SHALL BE RESPONSIBLE FOR THE SAFETY OF THE WORK AREA, ADJACENT AREAS AND ANY PROPERTY OCCUPANTS WHO MAY BE AFFECTED BY THE WORK UNDER CONTRACT. THE CONTRACTOR SHALL REVIEW ALL LANDOWNER, PRIME CONTRACTOR, CARRIER, OSHA, AND LOCAL SAFETY GUIDELINES AND AT ALLWORKPLACE. TIMES SHALL CONFORM TO THE MOST RESTRICTIVE OF THESE STANDARDS TO ENSURE A SAFE 2. ALL SAFETY EOUIPMENT SHALL BE INSPECTED ACCORDING TO ALL OSHA AND INDUSTRY SCHEDULED INTERVALS AND ALL INSPECTIONS SHALL BE DOCUMENTED PER APPLICABLE CODES AND STANDARDS. 3. TOWER WORK PRESENTS ADDITIONAL THREATS TO HEALTH AND SAFETY. ALL TOWER WORKERS WORKING ON A TOWER MUST BE ADEOUATELY TRAINED AND MONITORED TO ENSURE THAT SAFE WORK PRACTICES ARE LEARNED AND FOLLOWED. AS REOUIRED BY OSHA, WHEN WORKING ON EXISTING COMMUNICATION TOWERS. EMPLOYEES MUST BE PROVIDED WITH APPROPRIATE FALL PROTECTION, TRAINED TO USE THIS FALL PROTECTION PROPERLY, AND THE USE OF FALL PROTECTION MUST BE CONSISTENTLY SUPERVISED AND ENFORCED BY THE CONTRACTOR. 4. ELECTRICAL WORK PRESENTS SPECIFIC THREATS TO THE HEALTH AND SAFETY OF WORKERS ON SITE. SPECIFICALLY ELECTROCUTIONS ARE THE FOURTH LEADING CAUSE OF DEATH ON CONSTRUCTION SITES. ALL ELECTRICAL WORKERS SHALL HAVE CURRENT CERTIFICATIONS WHICH SATISFY ALL TRAINING REQUIREMENTS FOR THE ELECTRICAL WORK THEY ARE PERFORMING PER OSHA STANDARDS. ALL ELECTRICAL WORKERS SHALL ADHERE TO ALL SAFETY RULES AND REGULATIONS FOR WORKER AND PUBLIC SAFETY. ALL WORK SHALL BE PERFORMED BY QUALIFIED ELECTRICIANS TRAINED FOR THE TYPE OF WORK AND THE VOLTAGES PRESENT FOR EACH TASK. THE CONTRACTOR SHALL REVIEW ALL LANDOWNER, PRIME CONTRACTOR, CARRIER, OSHA, NFPA 70, AND LOCAL SAFETY GUIDELINES AND AT ALL TIMES SHALL CONFORM TO THE MOST RESTRICTIVE OF THESE STANDARDS TO ENSURE A SAFE WORKPLACE) ; F P g g �-.a !ri @ L 7�. E at&t mobility :-MasTec Network Solutions t I GPD GROUP Professional Corporation 520 South Main Street, Suite 2531 Akron, OH 94311 330.572.2100 Fax: 330.572.2102 PROJECT NO: 2018723.04.25588.01 DRAWN BY: AGL CHECKED BY: JG 1 04/25/18 REVISED PER CLIENT COMMENTS 0 4/5/18 ISSUED FOR CONSTRUCTION A 2/9/18 ...4ISSUED FOR REVIEW U 1 UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A UCENSED PROFESSIONAL ENGINEER. TO ALTER THIS DOCUMENT. RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE- ROOFTOP i SHEET TITLE GENERAL NOTES SHEET NUMBER 30. CONTRACTOR SHALL SUBMIT A COMPLETE SET OF AS -BUILT REDLINES TO THE GENERAL CONTRACTOR UPON COMPLETION OF PROJECT AND PRIOR TO FINAL PAYMENT. GENERAL CONSTRUCTION NOTES RAY 09 911111 CO mllnity development 1 GN-2 _� • (43 EXISTING BUILDING -EXISTING BUILDING ZEXISTING ASPHALT PARKING EXISTING BETA SECTOR ANTENNA (SEE SHEET RF-1) ow•° N ,ags9 /q �o9T • /A • 116 I • EXISTING SAT&T SITE LOCATION (SEE SHEET ;L C-2) t XISTING BUILDING I4PN• 004000-0315 ZONING: CC-C EXISTING GAMMA & BETA SECTOR ANTENNA - (SEE SHEET RF 1) GEXIS I BUILDING ROOFTOP tL._ f._�_�� .EXIST BUILDING EXISTING ALPHA SECTOR ANTENNA SEE SHEET RF-1) T•1 , • 4 • Aeoe • -EXISTING BUILDING -EXISTING BUILDING 7 EXISTING ALPHA SECTOR ANTENNA (SEE SHEET RF-1) — S 146TH ST ZEXISTING BUILDING GEXISTING ASPHALT PARKING -EXISTING BUILDING 7 VICINITY MAP -14 iI t ._. T kite 4�Tly` Gnu_ Or •.:.;f �_ ::.a=r--vl y.A•t l j *Q 4 1 LY(. �I. r v 1 1 ! 1;i+.mow; 'y ,. a 1LL I`� ROOF AREA SCHEDULE ITEM AREA % COVERED ROOFTOP ±11734 SF ROOFTOP COVERAGE 3708 SF 6% OTHER CARRIER'S EQUIP. ±20 SF 0.17% EX. CABLE TRAYS ±660 SF 5.6% EX. ANTENNA SCREENS 311.3 SF 0.09% EX. EOUIPMENT ±15 SF 0.133 NEW EQUIPMENT 2 SF 0.02% RE SAFETY NOTE. AT&T HAS IMPLEMENTED RF SAFETY PROCEDURES AND ACTIONS ON THIS ROOFTOP SITE. ALL GENERAL SAFETY RECOMMENDATIONS WILL BE FOLLOWED IN ORDER TO COMPLY WITH FCC & COUNTY GUIDEUNES. rirl."--------EXISTING BUILDING E t • tfa. E. 1 0 EC: YF Jrr MAY 02 2018 Community Develoome t at&t mobility -NasTec Network Solutions GPD GROUP Professional Corporation 520 South Hain Street, Suite 2531 Akron, OH 44311 330.572.2100 Fax: 330.572.2102 PROJECT NO: 2018723.04.25588.01 DRAWN BY: AGL CHECKED BY: JG 1 04/25/18 REVISED PER CUENT COMMENTS 0 4/5/18 ISSUED FOR CONSTRUCTION A 2/9/18 ISSUED FOR REVIEW ,— RLESS YHNOIAT l5k zs PR �(F'I1CtJ UN EY ARE ACTING UNDER THE DIRECTION CE OF A UCENSED PROFESSIONAL ENGINEER, TO ALTER THIS DOCUMENT. RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE— ROOFTOP SHEET TITLE OVERALL SITE PLAN SHEET NUMBER C-1 22•x34• SCALE: 1/16' = 1'-0" ::...Ne .11.11 11•x17• SCALE: 1/32" = 1'-0• 16 12 8 4 0 16' OVERALL SITE PLAN 1 EXISTING AT&T \ GPS ANTENNA - INSTALL (1) NEW 4C bCEM CARD IN EXISTING PURCELL CABINET INSTALL (3) NEW CORDEX RECTIFIERS IN EXISTING POWER PLANT EXISTING AT&T CPS ANTENNA EXISTING AT&T WOOD FRAME ENCLOSURE (LTE r EXISTING AT&T PURCELL ai CABINET EXISTING AT&T BBU :1:.. WITH (20) MARATHON • BATTERIES EXISIING . •T&T POWER CABINET WITH (8) MARATHON BATTERIES EXISTING AT&T TE43 CABINET EXISTING AT&T DIPLEXERS EXISTING AT&T VERTICAL CABLE TRAY ROUTED UP EXTERIOR BUILDING WALL EXISTING SLIDING ACCESS GATES (TYP) EXISTING AT&T CABLE TRAY EXISTING AT&T TELCO PANEL EXISTING AT&T GENERATOR PLUG 0 -'EXISTING ASPHALT PARKING EXISTING AT&T WOOD FRAME ENCLOSURE (UMTS) EXISTING BOLLARD (TYP) II , 1' EXISTING AT&T UMTS '- ii! CABINET r _Nm... EXISTING AT&T POWER PANEL EXISTING AT&T METER 8'-0- 9'-3- EXISTING AT&T WOOD FRAME ENCLOSURE (GSM) EXISTING AT&T VERTICAL CABLE TRAY ROUTED UP EXTERIOR BUILDING WALL EXISTING AT&T GSM CABINET 8'-3- //////// n 7-0 EXISTING AT&T WOOD FRAME ENCLOSURE (EMPTY) 8'-3- • ZX!STING BUILDING n RECEVED MAY 02 201P Community Development at&t �� mobility -IasTec Network Solutions GPD GROUP Professional Corporation 520 South Main Street, Suite 2531 Akron, OH 44311 330.572.2100 Fax: 330.572.2102 PROJECT NO: 2018723.04.25588.01 DRAWN BY: AGL CHECKED BY: JG 1 04/25/18 REVISED PER CUENT COMMENTS 0 4/5/18 ISSUED FOR CONSTRUCTION A 2/9/1A eklip% FOR REVIEW 4,•._�.%NAL, • 04/26/18 2020 0 TAW FOR ANY PERSON. UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A LICENSED PROFESSIONAL ENGINEER. TO ALTER THIS DOCUMENT. RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE— ROOFTOP SHEET TITLE EQUIPMENT LAYOUT SHEET NUMBER C-2 22"x34- SCALE: 3/8- = 1 11-x17- SCALE: 3/16- = 1'-0' 2 1 0 2' EQUIPMENT LAYOUT 1 4. • EXISTING AT&T UMTS ANTENNA IN POS. 4 TO BE REMOVED EXISTING AT&T LTE ANTENNA IN POS. 1 TO BE RELOCATED EXISTING AT&T TMAs IN POS. 1 TO BE REMOVED EXISTING AT&T (2) FRP SHROUDS A.G.L. CENTER OF EXISTING AT&T ANTENNAS "F45'-0 AG.L TOP OF EXISTING PARAPET 9'40'-10" AG.L. .GRADE 0 SW CORNER Y 0'-0" A.G.L. OF BUILDING EXISTING AT&T RRH IN POS. 4 TO BE RELOCATED TO P1 EXISTING AT&T FRP ANTENNA SHROUD TO REMAIN (TYP.) TOP OF EXISTING AT&T (2) FRP SHROUDS A.G.L. 1 @1 III I I11111111111IIIII IIIII III I1111111111111111111111 III I11111111111101110 1111111111111111111111111 1111111111111111111111111 1111111111111111111111111 EXISTING BULDING 1111111111111111111111111 1111 a 1111111111111111111 1111111111111111111111111 -== m =_= m =_= m m -• EXISTING OTHER CARRIER • ANTENNAS (TYP) TOP OF EXISTING AT&T FRP SHROUD 51'-10" AG.L IIIIIIII IIII I IIIII1111111 1111111111111111111111111 1111111111111111111111111 1111111111111111111111111 1111111111111111111111111 1111111111111111111111111 II_• 1111111111111111111111 III-■ 1111111111111111111111 II_■ 1111111111111111111111 THE PASSING STRUCTURAL ANALYSIS FOR THE EXISTING TOWER AT THIS SITE WAS COMPLETED BY GPD GROUP PROFESSIONAL CORPORATION ON JANUARY 19, 2018. CONFORMING TO TIA-222—G. ACCORDING TO THE PASSING STRUCTURAL ANALYSIS, THE ROOFTOP HAS SUFFICIENT CAPACITY. STRUCTURAL ANALYSIS NOTE 3 IN ACCORDANCE WITH RF DATA SHEET DATED NOVEMBER 1, 2017 VERSION 2.0 RF DATA SHEET NOTE 4 22 x34" SCALE: 3/32" = 1'-0" 11"x17" SCALE: 3/64" = 1'-0" 8 4 0 8' EXISITING BUILDING EAST ELEVATION 1 EXISTING RELOCATED LTE AT&T ANTENNA IN POS. 4 PROPOSED AT&T LTE ANTENNA IN POS. 1 EXISTING AT&T (2) FRP SHROUDS A.G.L. AlRAD CENTER OF EXISTING AT&T ANTENNAS 45'-0" A.G.L. TOP OF EXISTING PARAPET 740'-10A.G.L. gPROPOSED AT&T RRH IN POSITION 1(1 PER SECTOR, 3 TOTAL) GRADE 0 SW CORNER OF BUILDING -44}0'-0" AGL Atei I_❑ !i1111111111111111111111111 III I 1111111111111111111111 III 1111111111111111111111 ISTING RELOCATED AT&T RRH UNIT IN POSITION 1 (1 PER SECTOR, 3 TOTAL) EXISTING AT&T FRP ANTENNA SHROUD TO REMAIN(TYP.) TOP OF POSTING AT&T (2) FRP SHROUDS. 50'-9" A.G.L. EXISTING BULDING EXISTING OTHER CARRIER ANTENNAS (TYP) AlTOP OF EXISTING AT&T FRP SHROUD 51'-10" A.G.L PROPOSED AT&T RRH UNIT (1 PER SECTOR, 3 TOTAL) NOTE: CONTRACTOR SHALL MATCH EXISTING CONCEALMENT FOR NEW EOUIPMENT. tip_=m =m m- 1111111111111111111111111 1111111111111111111111111 1111111111111111111111111 1111111111111111111111111 m-n- 1111111111111111111111111 1111111111111111111111111 111111111 1111111111111111 1111111111111111111111111 ;ELM 1111111111111111111111111 1111111111111111111111111 m-n- 1111111111111111111111111 1111111111111111111111111 1111111111111111111111 1111111111111111111111 II IN -- 1111111111111111111111 1. TYPES AND SIZES OF THE ANTENNA CABLE ARE BASED ON ESTIMATED LENGTHS. PRIOR TO ORDERING CABLE, CONTRACTOR SHALL VERIFY ACTUAL LENGTH BASED ON CONSTRUCTION LAYOUT AND NOTIFY THE PROJECT MANAGER IF ACTUAL LENGTHS EXCEED ESTIMATED LENGTHS. 2. CONTRACTOR SHALL VERIFY THE DOWN —TILT OF EACH ANTENNA WITH A DIGITAL LEVEL. 3. CONTRACTOR TO CONFIRM COAX COLOR CODING PRIOR TO CONSTRUCTION. REFER TO -ANTENNA SYSTEM LABELING STANDARD" ND-00027, REFER TO THE LATEST VERSION. 4. ALL JUMPERS TO THE ANTENNAS FROM THE MAIN TRANSMISSION LINE WILL BE 1/2" DIA. LDF AND SHALL NOT EXCEED 5. ALL COAXIAL CABLE WILL BE SECURED TO THE DESIGNED SUPPORT STRUCTURE, IN AN APPROVED MANNER, AT DISTANCES NOT TO EXCEED 4'-0" OC. 6. CONTRACTOR MUST FOLLOW ALL MANUFACTURER'S RECOMMENDATIONS REGARDING BOTH THE INSTALLATION AND GROUNDING OF ALL COAXIAL CABLES, CONNECTORS, ANTENNAS, AND ALL OTHER EQUIPMENT. 7. WEATHERPROOF ALL ANTENNA CONNECTORS WITH SELF AMALGAMATING TAPE. WEATHERPROOFING SHALL BE COMPLETED IN STRICT ACCORDANCE WITH AT&T STANDARDS. 8. CONTRACTOR SHALL GROUND ALL EQUIPMENT. INCLUDING ANTENNAS, RET MOTORS, TMA'S, COAX CABLES, AND RET CONTROL CABLES AS A COMPLETE SYSTEM. GROUNDING SHALL BE EXECUTED BY OUAUFIED WIREMEN IN COMPLIANCE WITH MANUFACTURER'S SPECIFICATION AND RECOMMENDATION. 9. CONTRACTOR SHALL PROVIDE STRAIN —RELIEF AND CABLE SUPPORTS FOR ALL CABLE ASSEMBLIES. COAX CABLES, AND RET CONTROL CABLES. CABLE STRAIN —RELIEFS AND CABLE SUPPORTS SHALL BE APPROVED FOR THE PURPOSE. INSTALLATION SHALL BE IN ACCORDANCE WITH MANUFACTURER'S SPECIFICATIONS AND RECOMMENDATIONS. 10. CONTRACTOR TO VERIFY THAT EXISTING COAX HANGERS ARE STACKABLE SNAP IN HANGERS. IF EXISTING HANGERS ARE NOT STACKABLE SNAP IN HANGERS THE CONTRACTOR SHALL REPLACE EXISTING HANGERS WITH NEW SNAP IN HANGERS IF APPLICABLE. COAXIAL ANTENNA CABLE NOTES RECEVE MAY 0' 2018 Community, Development at&t mobility -IIasTec Network Solutions 1- GPD GROUP Professional Corporation 520 South Main Street, Suite 2531 Akron, OH 44311 330.572.2100 Fax: 330.572.2102 PROJECT NO: 2018723.04.25588.01 DRAWN BY: AGL CHECKED BY: JG 1 04/25/18 REVISED PER CUENT COMMENTS 0 4/5/18 ISSUED FOR CONSTRUCTION A 2/8/ SUFj{I. FOR REVIEW .Pp A 41. AT 04/26/18 5 [-SPIRES 04/16/702n R IS A VIOLATION OF LAW FOR ANY PERSON, UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A UCENSED PROFESSIONAL ENGINEER, TO ALTER THIS DOCUMENT. RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE— ROOFTOP SHEET TITLE BUILDING ELEVATION SHEET NUMBER C-3 22'x34" SCALE: 3/32" = 11"x17" SCALE: 3/64" = 1'-0" 8 4 0 8' PROPOSED BUILDING EAST ELEVATION 2 NOT USED 6 (N) = NEW (X) - EXISTING (XR) - EXISTING/RELOCATED (XG) = EXISTING/GROUND (E) = ELECTRICAL (M) = MECHANICAL EXISTING ANTENNA CONFIGURATION AND CABLE SCHEDULE SECTOR POS STATUS ANTENNA ANTENNA rE HEIGHT AZIMUTH TMA/RRU DC SURGE AND DISTRIBUTION CABLE TYPE A 1 EXISTING KATHREIN 742-264 (X) 45'-0" AGL 80 (1) 1-E15Z01P39_(L9) (X) (1)(1)825H2e60-80o4RX)(X) (1) FC12 (X) (1) DC2 (X) (1) DC, (1) FIBER (X) 4 EXISTING KATHREIN 80010764 (X) 45'-0" AGL 80' (2) 2-LGP 21401_(U9) (X) (1) RRH2x40W-07L (X) (2) COAX (X) B 1 EXISTING KATHREIN 742-264 (X) 45'-0" AGL 240' (1) 1-E15Z01P39_(L9) (X) (1) RRH2x60-850 (X) (1) B25 RRH4X30-4R (X) (1) DC2 (X) (1) DC, (1) FIBER (X) 4 EXISTING KATHREIN 80010764 (X) 45'-0" AGL 240' (2) 2-LGP 21401_(U9) (X) (1) RRH2x40W-07L (X) (2) COAX (X) c 1 EXISTING KATHREIN 742-264 (X) 45.-0" AGL 330' (1) 1-E15Z01P39_(L9) (X) (1) RRH2x60-850 (X) (1) 825 RRH4X30-4R (X) (1) DC2 (X) (1) DC, (1) FIBER (X) 4 EXISTING KATHREIN 80010764 (X) 45'-0" AGL 330' (2) 2-LGP 21401_(U9) (X) (1) RRH2x40W-07L (X) (2) COAX (X) 11 1I II 11 11 II II I I II 1 r ti ! I 6,- EXISTING ROOFTOP ACCESS HATCH (3) EXISTING AT&T RRHs (1 PER SECTOR) FOR POSmON 4 TO BE RELOCATED TO POSITION 1 (TYP. OF 3 SECTORS) /i O EXISTING PARAPET EXISTING AT& ROOFTOP CABLE TRAY (TYP) -EXISTING y�� . BUILDINGa. ROOFTOPS �.., / I- (3) EXISTING AT&T PANEL ANTENNAS (1 PER SECTOR) IN POSmON 1 TO BE RELOCATED POSITION 4 (TYP. OF 3 SECTORS) KATHREIN 742-264) EXISTING PARAPET- \ 1/4 EXISTING AT&T ROOFTOP FIBER CONDUIT EXISTING AT&T HYBRID FIBER CABLE (1 PER SECTOR, 3 TOTAL) ''EXISTING BUILDING ROOFT0FL' \ 1 `EXISTING AT&T ROOFTOP CABLE TRAY (T(P) (3) EXISTING AT&T PANEL ANTENNAS IN POSITION 4 TO BE REMOVED (KATHREIN 80010764) `EXISTING ROOFTOP WALKING PADS EXSTING AT&T w_ TMA IN POSITION 1 _i (1 PER SECTOR, ■ 3 TOTAL) TO BE ,(,^�• a.tea REMOVED � ��J ti�i � S�•� �Fl 1 11 11 IT LI C EXISTING HYBRID FIBER CABLE I J \1 ••• EX STING AT& ROOFTOP CABLE TRAY (TYP) _JI ''EXISTING ROOFTOP WALKING PAD SI7 ''EXISTING BUILDING ROOFTOP-] (6) EXISTING AT&T RRH (2 PER SECTOR) IN POSmON 1 TO BE REMAIN (TYP. OF 3 SECTORS) EXISTING PARAPET ''EXISTING EXISTING AT&T BUILDING ANTENNA MOUNT ROOFTOP-! TO REMAIN EXISTING AT&T FRP ANTENNA SHROUD TO REMAIN EXISTING AT&T FRP /-- ANTENNA SHROUD TO REMPJN ID -,• �I I II Hi I I II 111111 EXISTING AT& ROOFTOP CABLE TRAY (TYP) EXISTING AT&T HYBRID FIBER CABLE (1 PER SECTOR, 3 TOTAL) • BOCTOZ M,UT EXISTING PARAPET ( 11 I 1 11 II I I 11 (1) EXISTING AT&T DC/FIBER DC2 SURGE DISTRIBUTION TO REMAIN I 1 I I I I I 11 1 _ il- _I BOCTOZ MUTH nn II EXISTING AT&T FIBER SPOOL BOX 1 (1 PER SECTOR, 3 TOTAL) TO REMAIN • (6) EXISTING AT&T TMAs (2 PER SECTOR) FOR POSITION 4 TO REMAIN (1YP. OF 3 SECTORS) b coo en tai ILI CCI at&t mobility --J -NasTec Network Solutions GPD GROUP Professional Corporation 520 South Maln Street, Suite 2531 Alum, OH 44311 330.572.2100 Fax: 330.572.2102 PROJECT NO: 2018723.04.25588.01 DRAWN BY: AGL CHECKED BY: JG 1 04/25/18 REVISED PER CLIENT COMMENTS 0 4/5/18 ISSUED FOR CONSTRUCTION A 2/9/18 . WSUig FOR REVIEW • . _ • • R YJ ..ur LAW FOR ANY PERSON. UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A UCENSED PROFESSIONAL ENGINEER, TO ALTER THIS DOCUMENT. RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE- ROOFTOP E ANTENNA CONFIGURATIONS SHEET TITLE SHEET NUMBER RF-1 EXISTING ANTENNA LAYOUT & SCHEDULE 22"x34" SCALE: 1" = 1'-0" 11"x17" SCALE: 1/2" = 1 -0" 1' 6' 1 AMMO°. ( 1 at8ct �� mobility PROPOSED ANTENNA CONFIGURATION AND CABLE SCHEDULE RFDS V. 2.0 DATED 11/1/17 (N) =NEW (X) = EXISTING (XR) - EXISTING/RELOCATED SECTOR POS STATUS ANTENNA ANTENNA RAD CENTER AZIMUTH TMA/RRU DC SURGE AND DISTRIBUTION CABLE TYPE (XG) = EXISTING/GROUND (E) = ELECTRICAL • (M) = MECHANICAL A 1 PROPOSED KATHREIN 80010798 (N) 45.-0" AGL 80' (1) RRH2x60-850 (X) (1) B25 RRH4X30-4R (X) (1) RRH2x40W-07L (XR) (1) RRH4x25-WCS-WR (N) (1) FC12 (X) (1) DC2 (X) (1) DC, (1) FIBER (%) 4 EXISTING KATHREIN 742-264 (XR) 38'-0" AGL 80' (2) 2-LGP 21401_(U9) (X) (2) COAX (X) 1 PROPOSED KATHREIN 80010798 (N) 45'-O" AGL 240' (1) RRH2x60-850 (X) (1) B25 RRH4X30-4R (%) (1) RRH2x40W-07L (XR) (1) RRH4x25-WCS-WR (N) (1) DC2 (X) (1) DC, (1) FIBER (X) r : I a sTe Network Solutions c B 4 EXISTING KATHREIN 742-264 (XR) 38..-0" AGL 240' (2) 2-LGP 21401_(U9) (X) (2) COAX (X) 1 PROPOSED KATHREIN 8001D798 (N) 45'-0" AGL 330' (1) RRH2x60-850 (X) (1) 825 RRH4X30-4R (X) (1) RRH2x40W-07L (XR) (1) RRH4x25-WCS-WR (N) (1) DC2 (X) (1) DC, (1) FIBER (X) A. c 4 EXISTING KATHREIN 742-264 (XR) 41'-0" AGL 330- (2) 2-LGP 21401_(U9) (X) (2) COAX (X) GPD GROUP Professional Corporation 520 South Hain Street, 44311Suite 1 OH Akron, OH .2102 330.572.2100 Fax: 330.5722102 — EXISTING ROOFTOP ACCESS HATCH / LEXISTING EXISTING AT&T FRP ANTENNA SHROUD TO REMAIN ROOFTOP EX STING AT& ROOFTOP WALKING CABLE TRAY (TYP) P �7 = I I — J I PROJECT NO: 2018723.04.25588.01 r DRAWN BY: AGL I � SECTOZ 11 1 I I I 11 I I I I 11 I I I 1 l 1 -i MU,. T EXISTING PARAPET 1 I I •• _...._ �® By CHECKED BY: JG t_ �c+ EXISTING AT&T ROOFTOP r ,_ _, • p FIBER CONDUIT I 9 _ - t _ EXISTING AT&T HYBRID EXISTING (� y '� • FIBER CABLE (1 PER SECTOR. 3 TOTAL) BUILDING ROOFTOP-j fl r-r n n n n El n n fl n n fl I r �% io I 1 04 /25 / 18 REVISED PER CUENT COMMENTS j �•♦ (3) PROPOSED AT&T RRH (1 � -� PER SECTOR) IN POSITION 1 ' 0 4/5/18 ISSUED FOR CONSTRUC11ON '� (TYP. OF 3 SECTORS) t A 2/9/ FOR REVIEW // : EXISTING PARAPET) EXISTING AT&T _ I ( A A CABLE TRAY � ( I I „�ROOFTOPP •`T� C `\'O ^S/.// �C• �O �� Gam. i . '" .�" `N'' in i �., .'-. f11j' i?:=:I s '` �� `t�C��rSI{;�,N v .., • V'' � (6) EXISTING AT&T RRH (2 PER CEO' yf ,.To (3) EXISTING RELOCATED AT&T PANEL ANTENNAS IN POSITION SECTOR) IN POSITION 1 (TYP. OF '1 4 (KATHREIN 742-264) 3 SECTORS) ) _ GEXISTING 1 BUILDING (3) EXISTING AT&T RRH (1 PER 1 ROOFTO SECTOR) IN POSITION 1 (TYP. OF _ Ile° 3 SECTORS) I - ,* GEXISTING EXISTING PARAPET —1— (1) DC/FIBER EXISTING DC2 AT&TDC2, BUILDING I G EXISTING AT&T DISTRIBUTION TO '• M,J//NAL . °- I-' 04/26/18 F PRES nail Ai?n9n cE ROOFTOP-j EXISTING REMAIN / EXISTING AY&ROOFTOP BUILDING ANTENNA MOUNT I CABLE TRAY (TYP) ROOFTO/ TO REMAIN I I EXISTING I I I I I II - ROOFTOP ( WALKING PADS EXISTING HYBRID I I -tr' A VIOLATION OF UAW FOR ANY PERSON. UNLESS THEY ARE ACING UNDER THE DIRECTION OF A UCENSED PROFESSIONAL ENGINEER. TO ALTER THIS DOCUMENT. t / S FIBER CABLE 1 / : _ _ f�l p�i y�'P /// ♦ �♦ I 1 n n EXISTING AT&T I ' g. C1, EXISTING AT&T FRP 1 , -FIBER SPOOL BOX 1-- Gjy •- �•• ..** o'♦ ANTENNA SHROUD = " I (1 PER SECTOR, ( I 3 TOTAL) — ..4 TO REMAIN I L SECTOR TH TO REMAIN ,-, `/ RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 981 8 U 6 LTE- ROOFTOP 80. AZ1MU = '♦♦�P^ r A. 1 r - _ ■�� - _..... .. - ��:.A 1_ (3) PROPOSED AT&T F ��I o o n �. Fla fl lill . I PANEL ANTENNAS (1 1�`J ...... ICJ -,�♦��I• 1.d = I PER SECTOR) IN '` " ' _-.---..-_.�, -._.._- _ POSITION 1 (TYP. OF c_. _-.c_._.-.._..__..-_._: _._..:: = 3 SECTORS) - �`� �~ — �"� I •8,�1% 1oc''1AJ `---_--- -' I I— KATHREIN 80010798) I C. I �, ;1 V�� SE'p P EXISTING AT& ROOFTOP / � �, C� 1.N CABLE TRAY (TYP) I 1= �-J 'C Q SHEET TITLE ANTENNA CONFIGURATIONS _� 1 E IH.. 2 = EXISTING PARAPET-� `-'�- ' '- EXISTING AT&T C. \` —I HYBRID FIBER CABLE (6) EXISTING AT&T TMAs (2 PER O C 11 SECTOR) FOR POSITION 4 TO '� _ (1 PER SECTOR, 3 TOTAL) REMAIN (TYP. OF 3 SECTORS) 1—•1J Q 7 I I I I I I II I — — "LI' 1 SHEET NUMBER RF-1.2 L L �� I III I I 11 I I III 11 I I I �— . I 111 PROPOSED ANTENNA LAYOUT 22"x34" SCALE: 1" = 1'-0" 11"x17" SCALE: 1/2" = 1 -0" 1 6' 0 1' 1 • PROP0.13/8' ANTENNA PIPE MOUNT ANDREW P/N #. MT 220-108' MINIMUM LENGTH TYPICAL PER LTE APPLICATION �, lit , •�� ' I III NOTE; MOUNTING OPTIONS ARE INCLUDED PRODUCTS WITH ANTENNA PURCHASE ) PROPOSED ANTENNA MOUNTING BRACKET ANDREW P/N Q. DB5083 PROPOSED ANTENNA PROPOSED ANTENNA MOUNTING BRACKET ANDREW P/N #. DB380 II — �, ♦ ♦ MOUNTING PIPE NEW PLATE MOUNT BRACKET ) PIPE MOUNT KATHREIN 80010798 '1111.1.0.,...t.........)d, atxt mobility rnili, DIMENSIONS, HxWxD: 1993x375x 170mm (78.5'x 14.8'x6.7') r -11asTec Network Solutions uI u u U u GPD GROUP Professional Corporation 520 south Maln Street, Suke 2531 Alum, OH 44311 330.572.2100 Fa: 330.572.2102 6.TCa S - VERIFY MOUNTING AND ALL MOUNTING ATTACHMENTSBEVERIFIED HARDWARE SHALL BE VERIFIED BY 14.8' I ATTACHMENT MANUFACTURER PROPOSED ANTENNA SPECIFICATIONS NO SCALE 1 ANTENNA MOUNTING DETAIL NO SCALE 2 RRH MOUNTING DETAIL NO SCALE 3 ALCATEL—LUCENT RRH4x25-WCS-4R DIMENSIONS, WxDxH: 21.2'x11.97-x7.18' PROJECT N0: 2018723.04.25588.01 WEIGHT. WITHOUT MOUNTING KIT: 52.9 Ibs DRAWN BY: AGL -__-__- e9 11.97' CHECKED BY: JG tt `=i� <i<< — 1 <i11j� i J 1 ` 7 <M13 s i 1Mi <M N ° 1 ski m Tel 9 > „ N I {I I i < 1 04/25/18 REVISED PER CUENT COMMENTS w �,/ L/ 0 4/5/18 ISSUED FOR CONSTRUCTION oe �; 11 ®� ® ®1211- ° <1 1i A 2/• -;,,rr,.,,,,k: ROA W d iy 441�EM , E,; �p0 A. I 11 <1 4� 1imm I �T of \\'ASJ1,, 'C� L r kC., C j• 12) �� O - LI •-• p a 1 11 11111 < 1 ° EEO IWl1WII mumIIIIIIIUII RRH SPECIFICATIONS DETAIL N0 SCALE 4 DETAIL NOT USED NO SCALE 5 DETAIL NOT USED NO SCALE 6 �, A 55771 I . 'per h'tatstt:Ni \�7 -SS4ONA1.`G:: : arm s 04/26/ 1 � - • ^ EEt +, E MAY 02 2018 Community Dcvcl�Nr„cIt -:xPIRES 04/ 16/2020 r R IS A VIOLATION OF LAW FOR ANY PERSON. UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A UCENSED PROFESSIONAL ENGINEER. TO ALTER THIS DOCUMENT. RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE— ROOFTOP SHEET TITLE ANTENNA & RRH UNIT DETAILS a SHEET NUMBER RF-2 � - DETAIL NOT USED No SCALE 7 DETAIL NOT USED NO SCALE 8 DETAIL NOT USED 1 NO SCALE 9 III .0.„% 0 4fro �. 1 rn, . . .- - at&t mobility • NOTICE 11 CAUTION i\ i)) ot) :.I a s Network Solutions Te c Beyond This Point you are entering a controlled area where RF emissions may exceed the FCC General Population Exposure Limits. Follow all posted signs and site guidelines for working in a RF environment. Beyond This Point you are entering a controlled area where RF emissions may exceed the FCC Occupational Exposure Limits. Obey all posted signs and site guidelines for working in a RF environment. ALERTING SIGN ALERTING SIGN ALERTING SIGN (FOR CELL SITE BATTERIES) (FOR DIESEL FUEL) . (FOR PROPANE) GENERAL SIGNAGE GUIDELINES .- Ref: 47CFR 1.1307(b) atat l/ • Ref:47CFR 1.130]0) 0atat Structure Type INFO SIGN #1 INFO SIGN #2 INFO SIGN #3 INFO SIGN #4 Striping NOTICE SIGN CAUTION SIGN ALERTING SIGN S T A Towers monopole/Monopine/Nbnopalm entrance gates, shelter doors OR on the outdoor cabinets climbing side of the Tow er On the side of Antennas entrance gates, shelter doors OR on the outdoor cabinets At the height of the first clirbing step, min. 9ft above ground GPD GROUP Professional Corporation 520 South Hain Street, Suite 2531 0H 44311 x: 330.572.2102 330.572.2100 Fax ‘-- Y B SCE Towers/ Towers with high voltage entrance gates, shelter doors OR on the outdoor cabinets climbing side of the Tower On the side of Antennas entrance gates, shelter doors OR on the outdoor cabinets At the height of the first climbing step, min. 9ft above ground WARNING! / atat �1 • PROPERTY OF AT&T DANGER DO NOT TOUCH TOWER! SERIOUS "RF" BURN HAZARD! MAINTAIN AN ADEQUATE CLEARANCE BETWEEN TOWER SUPPORTS AND GUY WIRES FAILURE TOOBEY All. POSTEDSIGNS AND 5ITE GUIDELINES FOR WORKING INA RADIO FRE01113N'CV ENVIRON61i2T COULD RI'SUI.T IN SERIOUS INURE. CONTACT CURRENT MAY EXCEED LOUTS PRESCRIBED IN ANSI/IWI) 0)S1'199a FVRODNTRONI:D ISMTRON6119.T5. AUTHORIZED PERSONNEL ONLY PROJECT N0: 2018723.04.25588.01 DRAWN BY: AGL A C K Light Poles /Flag Poles entrance gates, shelter doors OR on the outdoor cabinets on the pole, no less than 3ft below the Antenna and no less than 9ft above ground On the side of Antennas entrance gates, shelter doors OR on the outdoor cabinets CHECKED BY: JG 3 Utility Wood Poles (JPA) entrance gates, shelter doors OR on the outdoor cabinets on the pole, no less than 3ft below the Antenna and no less than 9ft above ground On the side of Antennas entrance gates, shelter doors OR on the outdoor cabinets If GP max value of VFE at antenna level is: 0-99%: Notice sign; over 99%: Caution sign at no less than 3ft below antenna and 9ft above ground • 68tat • IN CASE OF EMERGENCY, OR PRIOR TO 1 04/25/18 REVISED PER CUENT COMMENTS o 4/5/18 ISSUED FOR CONSTRUCTION PERFORMING MAINTENANCE ON THIS SITE, CALL 800-638-2822 AND REFERENCE CELL SITE NUMBER A 2/0/18 ISSUED FOR REVIEW ALERTING SIGN •/ 1 F E E Mcrocells mounted on non IPA poles entrance gates, shelter doors OR on the outdoor cabinets on the pole, no less than 3ft below the Antenna and no less than 9ft above ground On the side of Antennas entrance gates, shelter doors OR on the outdoor cabinets Notice or Caution sign at no less than 9ft above ground: only if the exposure exceeds 90% of the General Public exposure at 6ft above ground or at outside surface of adjacent buildings NO SCALE E E 0 E 0 \ E\ LY C E cE ALERTING SIGN INFO SIGN #4 T Roof Tops At all access points to the roof X X On Antennas X X X F Concealed Antennas X X X R antennas mounted facing outside the building X X X INFORMATION antennas on support structure X X X o Roofview Graph: in m ATM open.. tekammmeleationa antemaaal 166 location. Remain least maway Doman).Wennnend obey ell goaeAsign. tConlerl the an UemmmaoflM emenvala)Lefmn working rlmer16en34er Comm1 ATMT.1 prior to peefomunS any M Radiation area i3ft from antenna s within X adjacent to each antenna X either Notice or Cautions n based on sign ( R IS A VIOLATION OF LAW FOR ANY PERSON, UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A LICENSED PROFESSIONAL ENGINEER, TO ALTER THIS DOCUMENT. A N Radiation area is beyond 3ft from antenna X adjacent to each antenna X diagonal, yellow striping as to Roofview graph Roofview results) at antennas/barrier ' tenancam m,nin near NEAT antennas This is Sher INFORMATION T E Church Steeples Access to steeple adjacent to antennas if antennas are concealed On the side of Antennas Access to steeple Caution sign at the antennas Cn�,tthe ana„•amer wif66door/hate6/gamisfd.,*Wed. ACTIVE ANTENNAS ARE MOUNTED RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE— ROOFTOP INFORMACION ONTHF.OVSIDEOFTLI58NLDING Ro„N�n„Spti.Fy R 0 ON THIS STRUCT E pApbd blommbn.4 .®mom o dopsA,aT. Dommmmnmum dabm+a de m mein de 3 piny *ogee., ma. lemma latum,rootrob ..pep... aepapr.m,pdrm.anima. tn6�kroaam6m,amedWmebbamd•, pMdeWmbm Cammag.rearATAT_antmdemagm magpie,mmbnlaleema repnmebwaeerta do la mmnmdeAna. pm,.1•e.melont.emmmm_ eamaame emem WtlRndedg. dminlavmbv hladihuaieau pueao poerman n ton y. lin e STAY BACK A MINIMUM OF FEET FROM THESE ANTENNAS Cemael AThTm and Wow Itrlr mmbru®pdmla feet tmralolrnmeed rtpin rMer than l keel . the mtrmu T6b b ATM db N N A Water Stations Access to ladder adjacent to antennas if antennas are concealed On the sloe of Antennas Access to ladder Caution sign beside Info sign #1, mn. 9ft above ground T n SHEET TITLE :.• SIGNAGE DETAILS NDtes for Rooftop sites: k>�as ti. • alit • W atat rtat 1. Ether NOTICE or CAUTION signs need to be posted at each sector as close as possible to: the outer edge of the striped off area or the outer antennas of the sector. rt`� Y 1 2. If Roofview shows: only blue = Notice Sign, blue and yellow = Caution Sign, only yellow = Caution Sign to be installed. MAY 02 21 3. Should the required striping area interfere with any structures or equipment (A/C, vents, roof hatch, doors, other antennas, dishes, etc.), please notify AT&T to modify the striping area, prior to starting the work Co m m u n i t SHEET NUMBER / RF-2 INFO SIGN #1 INFO SIGN #2 INFO SIGN #3 Dvt:ivpllit. SIGNAGE GUIDELINES CHART , ___.. • • .0, R�® at&'t mobility NOTE: GROUND LEAD INSIDE RUBBER GROMMET TO BE ATTACHED WITH X-CROSS ZIP TIES TO BRACKET. DO NOT USE SNAP -IN HANGERS AROUND GROUNDS. SECTOR ANTENNA -II asTec Network Solutions ANTENNA PIPE MOUNT TOP JUMPER CABLE (TYP.) NEW #2 AWG •GROUND i — GPD GROUP professional Corporation 520 South Maln Street, Suite 2531 AVM, OH 44311 330.572.2100 Fax: 330.572.2102 NOT USED NO SCALE 2 - NOT USED No scALE 3 EACH GROUND CONDUCTOR TERMINATING ON ANY GROUND BAR SHALL HAVE AN IDENTIFICATION TAG ATTACHED AT NEWTON INSTRUMENT COMPANY, INC. EACH END THAT WILL IDENTIFY ITS ORIGIN AND DESTINATION BUTNER, N.C. PROJECT NO: 2018723.04.25588.01 REQUIRED PART NUMBER DESCRIPTION SECTION "P" - SURGE PROTECTORS TO EXISTING SECTOR GROUND BAR NO DRAWN BY: AGL (EC) CELL REFERENCE GROUND BAR (IF COLLOCATED) O1 1 1/4'x4"x30� SOLID GROUND BAR O (EC) GENERATOR FRAMEWORK (IF AVAILABLE) (#2 AWG) \ RRUS UNIT (SEE NOTE 2) (EC) TELCO GROUND BAR (#2 AWG) CHECKED BY: JG O 2 A-6056 WALL MOUNTING DOUBLE CRIMP (EC) COMMERCIAL POWER COMMON NEUTRAL/GROUND BOND (3/0) JUMPER CABLES BRACKET CONNECTION (EC) FIBER GROUND BAR (#2 AWG) O3 2 3061-4 INSULATORS GROUND 0 © (EC) POWER ROOM REFERENCE GROUND BAR (AT&T) RECTIFIER FRAMES (#2 AWG) R NGIOR �, 0 SECTION "A" - SURGE ABSORBERS O4 3012-1 5/8"-11x1" H.H.C.S. 0 0 K"-,.�, /i% �f 0 (Ec) INTERIOR GROUND RING (#2 AWG) 1 Os/2s/18 REVISED PER CUENT COMMENTS OS 4 3015-8 5/8" LOCKWASHER �� ' 1 0 (EC) EXTERNAL EARTH GROUND FIELD (BURIED (EC) METALLIC COLD WATER PIPE (IF AVAILABLE) GROUND RING) (#2 AWG) (1/0 AWG) EX. SECTOR �--� GROUND BAR (1) PER SECTOR (TYP.) • /, RAYCAP 0 4/5/18 ISSUED FOR CONSIRUCI1ON ` A 2/8/ R REVIEW DETAIL NOTES: 1 (i %2 P �r` 4 (EC) BUILDING STEEL (IF AVAILABLE) (1/0 AWG) . ,V p. Sri/ 1. EXOTHERMICALLY WELD #2 AWG BARE TINNED SOLID " (SEE NOTE 1) SECTION "I" - ISOLATED GROUND ZONE - - • DC6-48-60 18 8F , r L;� 0% \�ASy/.1 �G J k� �C • �C i 0 (� i +rf� • ‘4*:" // UNIT COPPER CONDUCTOR TGROUND BAR. ROUTE CONDUCTOR TO BURIED GROUND RING AND PROVIDE PARALLEL EXOTHERMIC WELD. 2, THE INSTALLER SHALL USE PERMANENT MARKER TO DRAW THE LIKE BETWEEN SECTION AND LABEL EACH SECTION ("P", "A", "I" WITH 1" HIGH LETTERS / / 1/4"^�G+;'� 13" 4„ 13„ (AT&T) ALL ISOLATED GROUND REFERENCE (AT&T) GROUND WINDOW BAR EX. COLLECTION GROUND BAR —__ + LU NEW #2 AWG GROUND TO EXISTING COLLECTION GROUND T BAR FIBER 1MGB) REFERENCE GROUNDING BAR DETAIL NO SCALE 4 t tip pp 50744 Og' `F(i/SCIVYY �3VV 4/26/ 18 #4 OR #6 AWG STRANDED 600V,CU OTHWN-2R WITH INSULATION GREEN,"SS'in / GROUND BAR ON WALL OR FLOOR 1 1 1 1 1 1 LStPIRES: 02/03/2020 rt IT IS A VIOLATION OF LAW FOR ANY PERSON, UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A UCENSED PROFESSIONAL ENGINEER, TO ALTER THIS DOCUMENT. EQUIPMENT CABINET OO OO OO 9 9 g 1/16" 0WA6428 RIVERTON NORTH 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE- ROOFTOP 1 (GROUND ALL NEW CABINETS) -FI (2) TWO EXOTHERMIC TO BE USED WITH AWG SOLID BARE TINNED .... ggam� Fl ECElVE.D EX. EQUIPMENT GROUND BAR SHEET TITLE GROUNDING DETAILS NOTE: BOND 'ALL METALLIC OBJECTS TO GROUND BAR AT EQUIPMENT LOCATIONS COPPER GROUND CONDUCTOR, EXOTHERMIC WELD TO BURIED GROUND RING AND GROUND BAR PVC NONMETALLIC CONDUIT SCH 40 TYPE (NMC) CONDUIT WITH STRAP WITHIN TWO INCHES OF CONDUIT END Ire Yb�YV MAY O 2 �� -- Community - F 8_ C m t , SHEET NUMBER E-1 GROUNDING RISER DIAGRAM NO SCALE 1 GROUNDING BAR DETAIL I NO SCALE 5 NOT USED NO SCALE 6 PART 1 - GFNFRAI 1.1 GENERAL CONDITIONS: A. CONTRACTOR SHALL INSPECT THE EXISTING SITE CONDITIONS PRIOR TO SUBMITTING BID. ANY OUESTIONS ARISING DURING THE BID PERIOD IN REGARDS TO THE CONTRACTORS FUNCTIONS, THE SCOPE OF WORK, OR ANY OTHER ISSUE RELATED TO THIS PROJECT SHALL BE BROUGHT UP DURING THE BID PERIOD WITH THE PROJECT MANAGER FOR CLARIFICATION, NOT AFTER THE CONTRACT HAS BEEN AWARDED. B. THE CONTRACTOR SHALL OBTAIN PERMITS, LICENSES, MAKE AU. DEPOSITS, AND PAY ALL FEES REQUIRED FOR THE CONSTRUCTION PERFORMANCE FOR THE WORK UNDER THIS SECTION. C. DRAWINGS SHOW THE GENERAL ARRANGEMENT OF ALL SYSTEMS AND COMPONENTS COVERED UNDER THIS SECTION. THE CONTRACTOR SHALL VERIFY ALL DIMENSIONS. DRAWING SHALL NOT BE SCALED TO DETERMINE DIMENSIONS. 1.2 LAWS. REGULATIONS, ORDINANCES. STATUTES AND CODES. A. ALL WORK SHALL BE INSTALLED IN ACCORDANCE WITH THE LATEST EDITION OF THE NATIONAL ELECTRICAL CODE. AND ALL APPLICABLE LOCAL LAWS, REGULATIONS, ORDINANCES, STATURES AND CODES. CONDUIT BENDS SHALL BE THE RADIUS BEND FOR THE TRADE SIZE OF CONDUIT IN COMPLIANCE WITH THE LATEST EDITIONS OF NEC. • 1.3 REFERENCES: A. THE PUBLICATIONS LISTED BELOW ARE PART OF THIS SPECIFICATION. EACH PUBLICATION SHALL BE THE LATEST REVISION AND ADDENDUM IN EFFECT ON THE DATE. THIS SPECIFICATION IS ISSUED FOR CONSTRUCTION UNLESS OTHERWISE NOTED. EXCEPT AS MODIFIED BY THE REQUIREMENT SPECIFIED HEREIN OR THE DETAILS OF THE DRAWINGS, WORK INCLUDED IN THIS SPECIFICATION SHALL CONFORM TO THE APPLICABLE PROVISION OF THESE PUBLICATIONS. 1. ANSI/IEEE (AMERICAN NATIONAL STANDARDS INSTITUTE) 2. ASTM (AMERICAN SOCIETY FOR TESTING AND MATERIALS) 3. ICEA (INSULATED CABLE ENGINEERS ASSOCIATION) 4. NEMA (NATIONAL ELECTRICAL MANUFACTURER'S ASSOCIATION) 5. NFPA (NATIONAL FIRE PROTECTION ASSOCIATION) 6. OSHA (OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION) 7. UL (UNDERWRITERS LABORATORIES INC.) 8. AT&TGROUNDING AND BONDING STANDARDS TP-76416 1.4 SCOPE OF WORK A. WORK UNDER THIS SECTION SHALL CONSIST OF FURNISHING ALL LABOR. MATERIAL, AND ASSOCIATED SERVICES REQUIRED TO COMPLETE REQUIRED CONSTRUCTION AND BE OPERATIONAL. B. ALL ELECTRICAL EQUIPMENT UNDER THIS CONTRACT SHALL BE PROPERLY TESTED. ADJUSTED, AND ALIGNED BY THE CONTRACTOR. C. THE CONTRACTOR SHALL BE RESPONSIBLE FOR ALL EXCAVATING. DRAINING. TRENCHES, BACKFILUNG. AND REMOVAL OF EXCESS DIRT. D. THE CONTRACTOR SHALL FURNISH TO THE OWNER WITH CERTIFICATES OF A FINAL INSPECTION AND APPROVAL FROM THE INSPECTION AUTHORITIES HAVING JURISDICTION. E. THE CONTRACTOR SHALL PREPARE A COMPLETE SET OF AS -BUILT DRAWINGS. DOCUMENT ALL WIRING EQUIPMENT CONDITIONS. AND CHANGES WHILE COMPLETING THIS CONTRACT. THE AS -BUILT DRAWINGS SHALL BE SUBMITTED AT COMPLETION OF THE PROJECT. PART 2 - PRODUCTS 2.1 GENERAL: A. ALL MATERIALS AND EOUIPMENT SHALL BE UL LISTED. NEW, AND FREE FROM DEFECTS. B. ALL ITEMS OF MATERIALS AND EOUIPMENT SHALL BE ACCEPTABLE TO THE AUTHORITY HAVING JURISDICTION AS SUITABLE FOR THE USE INTENDED. C. ALL EQUIPMENT SHALL BEAR THE UNDERWRITERS LABORATORIES LABEL OF APPROVAL, AND SHALL CONFORM TO REQUIREMENT OF THE NATIONAL ELECTRICAL CODE. D. ALL OVERCURRENT DEVICES SHALL HAVE AN INTERRUPTING CURRENT RATING THAT SHALL BE GREATER THAN THE SHORT CIRCUIT CURRENT TO WHICH THEY ARE SUBJECTED, 10,000 AIC MINIMUM. VERIFY AVAILABLE SHORT CIRCUIT CURRENT DOES NOT EXCEED THE RATING OF ELECTRICAL EQUIPMENT IN ACCORDANCE WITH ARTICLE 110.24 NEC OR THE MOST CURRENT ADOPTED CODE PER THE GOVERNING JURISDICTION. 2.2 MATERIALS AND EOUIPMENT: A. CONDUIT: 1. RIGID METAL CONDUIT (RMC) SHALL BE HOT -DIPPED GALVANIZED INSIDE AND OUTSIDE INCLUDING ENDS AND THREADS AND ENAMELED OR LACOUERED INSIDE IN ADDITION TO GALVANIZING. 2. LIOUIDTIGHT FLEXIBLE METAL CONDUIT SHALL BE UL LISTED. 3. CONDUIT CLAMPS. STRAPS AND SUPPORTS SHALL BE STEEL OR MALLEABLE IRON. ALL FITTINGS SHALL BE COMPRESSION AND CONCRETE TIGHT TYPE. GROUNDING BUSHINGS WITH INSULATED THROATS SHALL BE INSTALLED ON ALL CONDUIT TERMINATIONS. 4. NONMETALLIC CONDUIT AND FITTINGS SHALL BE SCHEDULE 40 PVC. INSTALL USING SOLVENT -CEMENT -TYPE JOINTS AS RECOMMENDED BY THE MANUFACTURER. 8. CONDUCTORS AND CABLE: 1. CONDUCTORS AND CABLE SHALL BE FLAME-RETARDANT. MOISTURE AND HEAT RESISTANT THERMOPLASTIC, SINGLE CONDUCTOR, COPPER. TYPE THHN/THWN-2, 600 VOLT, SIZE AS INDICATED. #12 AWG SHALL BE THE MINIMUM SIZE CONDUCTOR USED. 2. N10 AWG AND SMALLER CONDUCTOR SHALL BE SOLID OR STRANDED AND #8 AWG AND LARGER CONDUCTORS SHALL BE STRANDED. 3. SOLDERLESS, COMPRESSION -TYPE CONNECTORS SHALL BE USED FOR TERMINATION OF ALL STRANDED CONDUCTORS. 4. STRAIN -RELIEF SUPPORTS GRIPS SHALL BE HUBBELL KELLEMS OR APPROVED EQUAL. CABLES SHALL BE SUPPORTED IN ACCORDANCE WITH THE NEC AND CABLE MANUFACTURER'S RECOMMENDATIONS. 5. ALL CONDUCTORS SHALL BE TAGGED AT BOTH ENDS OF THE CONDUCTOR. AT ALL PULL BOXES. J-BOXES. EOUIPMENT AND CABINETS AND SHALL BE IDENTIFIED WITH APPROVED PLASTIC TAGS (ACTION CRAFT, BRADY. OR APPROVED EQUAL). C. DISCONNECT SWITCHES: 1. DISCONNECT SWITCHES SHALL BE HEAVY DUTY, DEAD -FRONT, QUICK -MAKE, QUICK -BREAK. EXTERNALLY OPERABLE, HANDLE LOCKABLE AND INTERLOCK WITH COVER IN CLOSED POSITION, RATING AS INDICATED, UL LABELED FURNISHED IN NEMA 3R ENCLOSURE. SOUARE-D OR ENGINEER APPROVED EOUAL. D. CHEMICAL ELECTROLYTIC GROUNDING SYSTEM: 1. INSTALL CHEMICAL GROUNDING AS REQUIRED. THE SYSTEM SHALL BE ELECTROLYTIC MAINTENANCE FREE ELECTRODE CONSISTING OF RODS WITH A MINIMUM #2 AWG CU EXOTHERMICALLY WELDED PIGTAIL, PROTECTIVE BOXES, AND BACKFILL MATERIAL. MANU ACTURER SHALL BE LYNCOLE XIT GROUNDING ROD TYPES K2 -(*)CS OR K2L-(4)CS (•) LENGTH AS REOUIRED. • 2. GROUND ACCESS BOX SHALL BE A POLYPLASTIC BOX FOR NON -TRAFFIC APPLICATIONS. INCLUDING BOLT DOWN FLUSH COVER WITH "BREATHER" HOLES, XIT MODEL 1)XB-22. ALL DISCONNECT SWITCHES AND CONTROLLING DEVICES SHALL BE PROVIDED WITH ENGRAVED LAMICOID NAMEPLATES INDICATING EQUIPMENT CONTROLLED, BRANCH CIRCUITS ID NUMBERING. AND THE ELECTRICAL POWER SOURCE. 3. BACKFILL MATERIAL SHALL BE LYNCONITE AND LYNCOLE GROUNDING GRAVEL. E. SYSTEM GROUNDING: 1. ALL GROUNDING COMPONENTS SHALL BE TINNED AND GROUNDING CONDUCTOR SHALL BE #2 AWG BARE. SOLID. TINNED. COPPER. ABOVE GRADE GROUNDING CONDUCTORS SHALL BE INSULATED WHERE NOTED. 2. GROUNDING BUSES SHALL BE BARE. TINNED, ANNEALED COPPER BARS OF RECTANGULAR CROSS SECTION. STANDARD BUS BARS MGB, SHALL BE FURNISHED AND INSTALLED BY THE CONTRACTOR. THEY SHALL NOT BE FABRICATED OR MODIFIED IN THE FIELD. ALL GROUNDING BUSES SHALL BE IDENTIFIED WITH MINIMUM 3/4" LETTERS BY WAY OF STENCILING OR DESIGNATION PLATE. 3. CONNECTORS SHALL BE HIGH -CONDUCTIVITY, HEAVY DUTY. LISTED AND LABELED AS GROUNDING CONNECTORS FOR THE MATERIALS USED. USE TWO -HOLE COMPRESSION LUGS WITH HEAT SHRINK FOR MECHANICAL CONNECTIONS. INTERIOR CONNECTIONS USE TWO -HOLE COMPRESSION LUGS WITH INSPECTION WINDOW AND CLEAR HEAT SHRINK. 4. EXOTHERMIC WELDED CONNECTIONS SHALL BE PROVIDED IN KIT FORM AND SELECTED FOR THE SPECIFIC TYPES, SIZES. AND COMBINATIONS OF CONDUCTORS AND OTHER ITEMS TO BE CONNECTED. 5. GROUND RODS SHALL BE COPPER -CLAD STEEL WITH HIGH -STRENGTH STEEL CORE AND ELECTROLYTIC -GRADE COPPER OUTER SHEATH, MOLTEN WELDED TO CORE, 5/8"x10'-0". ALL GROUNDING RODS SHALL BE INSTALLED WITH INSPECTION SLEEVES. 6. INSTALL AN EOUIPMENT GROUNDING CONDUCTOR IN ALL CONDUITS IN COMPLIANCE WITH THE AT&T SPECIFICATIONS AND NEC. THE EQUIPMENT GROUNDING CONDUCTORS SHALL BE BONDED AT ALL JUNCTION BOXES, PULLBOXES, DISCONNECT SWITCHES. STARTERS, AND EQUIPMENT CABINETS. F. OTHER MATERIALS: 6. THE CONTRACTOR SHALL PROVIDE OTHER MATERIALS. THOUGH NOT SPECIFICALLY DESCRIBED, WHICH ARE REOUIRED FOR A COMPLETELY OPERATIONAL SYSTEM AND PROPER INSTALLATION OF THE WORK. 7. PROVIDE PULL BOXES AND JUNCTION BOXES WHERE SHOWN OR REOUIRED BY NEC. G. PANELS AND LOAD CENTERS: 1. ALL PANEL DIRECTORIES SHALL BE TYPEWRITTEN. PART 3 - EXECUTION 3.1 GENERAL: A. ALL MATERIAL AND EQUIPMENT SHALL BE INSTALLED IN STRICT ACCORDANCE WITH THE MANUFACTURER'S RECOMMENDATIONS. B. EQUIPMENT SHALL BE TIGHTLY COVERED AND PROTECTED AGAINST DIRT OR WATER. AND AGAINST CHEMICAL OR MECHANICAL INJURY DURING INSTALLATION AND CONSTRUCTION PERIODS. 3.2 LABOR AND WORKMANSHIP: A. ALL LABOR FOR THE INSTALLATION OF MATERIALS AND EOUIPMENT FURNISHED FOR THE ELECTRICAL SYSTEM SHALL BE INSTALLED BY EXPERIENCED WIREMEN, IN A NEAT AND WORKMAN -LIKE MANNER. B. ALL ELECTRICAL EQUIPMENT SHALL BE ADJUSTED, ALIGNED AND TESTED BY THE CONTRACTOR AS REQUIRED TO PRODUCE THE INTENDED PERFORMANCE. C. UPON COMPLETION OF WORK, THE CONTRACTOR SHALL THOROUGHLY CLEAN ALL EXPOSED EQUIPMENT. REMOVE ALL LABELS AND ANY DEBRIS, CRATING OR CARTONS AND LEAVE THE INSTALLATION FINISHED AND READY FOR OPERATION. 3.3 COORDINATION: A. THE CONTRACTOR SHALL COORDINATE THE INSTALLATION OF ELECTRICAL ITEMS WITH THE OWNER -FURNISHED EOUIPMENT DELIVERY SCHEDULE TO PREVENT UNNECESSARY DELAYS IN THE TOTAL WORK. 3.4 INSTALLATION: A. CONDUIT: 1. ALL ELECTRICAL WIRING SHALL BE INSTALLED IN CONDUIT AS SPECIFIED. NO CONDUIT OR TUBING OF LESS THAN 3/4 INCH TRADE SIZE. 2. PROVIDE RIGID PVC SCHEDULE 80 CONDUITS FOR ALL RISERS. RMC OTHERWISE NOTED. EMT MAY BE INSTALLED FOR EXTERIOR CONDUITS WHERE NOT SUBJECT TO PHYSICAL DAMAGE. 3. INSTALL SCHEDULE 40 PVC CONDUIT WITH A MINIMUM COVER OF 24" UNDER ROADWAYS. PARKING LOTS, STREETS. AND ALLEYS. CONDUIT SHALL HAVE A MINIMUM COVER OF 18" IN ALL OTHER NON -TRAFFIC APPLICATIONS (REFER TO 2008 NEC, TABLE 300.5). 4. USE GALVANIZED FLEXIBLE STEEL CONDUIT WHERE DIRECT CONNECTION TO EQUIPMENT WITH MOVEMENT, VIBRATION, OR FOR EASE OF MAINTENANCE. USE LIQUID TIGHT, FLEXIBLE METAL CONDUIT FOR OUTDOOR APPLICATIONS. INSTALL GALVANIZED FLEXIBLE STEEL CONDUIT AT ALL POINTS OF CONNECTION TO EQUIPMENT MOUNTED ON SUPPORT TO ALLOW FOR EXPANSION AND CONTRACTION. 5. A RUN OF CONDUIT BETWEEN BOXES OR EQUIPMENT SHALL NOT CONTAIN MORE THAN THE EQUIVALENT OF THREE OUARTER-BENDS. CONDUIT BEND SHALL BE MADE WITH THE UL LISTED BENDER OR FACTORY 90 DEGREE ELBOWS MAY BE USED. 6. FIELD FABRICATED CONDUITS SHALL BE CUT SQUARE WITH A CONDUIT CUTTING TOOL AND REAMED TO PROVIDE A SMOOTH INSIDE SURFACE. 7. PROVIDE INSULATED GROUNDING BUSHING FOR ALL CONDUITS. 8. CONTRACTOR IS RESPONSIBLE FOR PROTECTING ALL CONDUITS DURING CONSTRUCTION. TEMPORARY OPENINGS IN THE CONDUIT SYSTEM SHALL BE PLUGGED OR CAPPED TO PREVENT ENTRANCE OF MOISTURE OR FOREIGN MATTER. CONTRACTOR SHALL REPLACE ANY CONDUITS CONTAINING FOREIGN MATERIALS THAT CANNOT BE REMOVED. 9. ALL CONDUITS SHALL BE SWABBED CLEAN BY PULLING AN APPROPRIATE SIZE MANDREL THROUGH THE CONDUIT BEFORE INSTALLATION OF CONDUCTORS OR CABLES. CONDUIT SHALL BE FREE OF DIRT AND DEBRIS. 10. INSTALL PULL STRINGS IN ALL CLEAN EMPTY CONDUITS. IDENTIFY PULL STRINGS AT EACH END. 11. INSTALL 2" HIGHLY VISIBLE AND DETECTABLE TAPE 12" ABOVE ALL UNDERGROUND CONDUITS AND CONDUCTORS. 12. CONDUITS SHALL BE INSTALLED IN SUCH A MANNER AS TO INSURE AGAINST COLLECTION OF TRAPPED CONDENSATION. 13. PROVIDE CORE DRILLING AS NECESSARY FOR PENETRATIONS TO ALLOW FOR RACEWAYS AND CABLES TO BE ROUTED THROUGH THE BUILDING. DO NOT PENETRATE STRUCTURAL MEMBERS. SLEEVES AND/OR PENETRATIONS IN FIRE RATED CONSTRUCTION SHALL BE EFFECTIVELY SEALED WITH FIRE RATED MATERIAL WHICH SHALL MAINTAIN THE FIRE RATING OF THE WALL OR STRUCTURE. FIRE STOPS AT FLOOR PENETRATIONS SHALL PREVENT PASSAGE OF WATER, SMOKE. FIRE, AND FUMES. ALL MATERIAL SHALL BE UL APPROVED FOR THIS PURPOSE. 3.5 ACCEPTANCE TESTING: B. CONDUCTORS AND CABLE: 1. ALL POWER WIRING SHALL BE COLOR CODED AS FOLLOWS: DESSCCRIAION 208/240/120 VOI T SYSTEMS P E BLACK PHASE B RED PHASE C BLUE NEUTRAL WHITE GROUNDING GREEN 2. SPLICES SHALL BE MADE ONLY AT OUTLETS, JUNCTION BOXES. OR ACCESSIBLE RACEWAY CONDUITS APPROVED FOR THIS PURPOSE. 3. PULLING LUBRICANTS SHALL BE UL APPROVED. CONTRACTOR SHALL USE NYLON OR HEMP ROPE FOR PULLING CONDUCTOR OR CABLES INTO THE CONDUIT. 4. CABLES SHALL BE NEATLY TRAINED. WITHOUT INTERLACING, AND BE OF SUFFICIENT LENGTH IN ALL BOXES & EQUIPMENT TO PERMIT MAKING A NEAT ARRANGEMENT. CABLES SHALL BE SECURED IN A MANNER TO AVOID TENSION ON CONDUCTORS OR TERMINALS. CONDUCTORS SHALL BE PROTECTED FROM MECHANICAL INJURY AND MOISTURE. SHARP BENDS OVER CONDUIT BUSHINGS IS PROHIBITED. DAMAGED CABLES SHALL BE REMOVED AND REPLACED AT THE CONTRACTOR'S EXPENSE. C. DISCONNECT SWITCHES: 1. INSTALL DISCONNECT SWITCHES LEVEL AND PLUMB. CONNECT TO WIRING SYSTEM AND GROUNDING SYSTEM AS INDICATED. D. GROUNDING: 1. ALL METALLIC PARTS OF ELECTRICAL EOUIPMENT WHICH DO NOT CARRY CURRENT SHALL BE GROUNDED IN ACCORDANCE WITH THE REQUIREMENTS OF THE BUILDING MANUFACTURER, AT&T GROUNDING AND BONDING STANDARDS TP-76416, ND-00135. AND THE NATIONAL ELECTRICAL CODE. 2. PROVIDE ELECTRICAL GROUNDING AND BONDING SYSTEM INDICATED WITH ASSEMBLY OF MATERIALS, INCLUDING GROUNDING ELECTRODES, BONDING JUMPERS AND ADDITIONAL ACCESSORIES AS REOUIRED FOR A COMPLETE INSTALLATION. 3. ALL GROUNDING CONDUCTORS SHALL PROVIDE A STRAIGHT DOWNWARD PATH TO GROUND WITH GRADUAL BEND AS REOUIRED. GROUNDING CONDUCTORS SHALL NOT BE LOOPED OR SHARPLY BENT. ROUTE GROUNDING CONNECTIONS AND CONDUCTORS TO GROUND IN THE SHORTEST AND STRAIGHTEST PATHS POSSIBLE TO MINIMIZE TRANSIENT VOLTAGE RISES. 4. BUILDINGS AND/OR NEW TOWERS GREATER THAN 75 FEET IN HEIGHT AND WHERE THE MAIN GROUNDING CONDUCTORS ARE REOUIRED TO BE ROUTED TO GRADE, THE CONTRACTOR SHALL ROUTE TWO GROUNDING CONDUCTORS FROM THE ROOFTOP, TOWERS, AND WATER TOWERS GROUNDING RING, TO THE EXISTING GROUNDING SYSTEM, THE GROUNDING CONDUCTORS SHALL NOT BE SMALLER THAN 2/0 AWG COPPER. ROOFTOP GROUNDING RING SHALL BE BONDED TO THE EXISTING GROUNDING SYSTEM, THE BUILDING STEEL COLUMNS. LIGHTNING PROTECTION SYSTEM. AND BUILDING MAIN WATER LINE (FERROUS OR NONFERROUS METAL PIPING ONLY). SEE STANDARD 6.3.2.2. 5. TIGHTEN GROUNDING AND BONDING CONNECTORS. INCLUDING SCREWS AND BOLTS, IN ACCORDANCE WITH MANUFACTURER'S PUBLISHED TOROUE TIGHTENING VALUES FOR CONNECTORS AND BOLTS. WHERE MANUFACTURER'S TOROUING REQUIREMENTS ARE NOT AVAILABLE. TIGHTEN CONNECTIONS TO COMPLY WITH TIGHTENING TORQUE VALUES SPECIFIED IN UL TO ASSURE PERMANENT AND EFFECTIVE GROUNDING. 6. CONTRACTOR SHALL VERIFY THE LOCATIONS OF GROUNDING TIE -IN -POINTS TO THE EXISTING GROUNDING SYSTEM. ALL UNDERGROUND GROUNDING CONNECTIONS SHALL BE MADE BY THE EXOTHERMIC WELD PROCESS AND INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S INSTRUCTIONS. 7. ALL GROUNDING CONNECTIONS SHALL BE INSPECTED FOR TIGHTNESS. EXOTHERMIC WELDED CONNECTIONS SHALL BE APPROVED BY THE INSPECTOR HAVING JURISDICTION BEFORE BEING PERMANENTLY CONCEALED. 8. APPLY CORROSION -RESISTANT FINISH TO FIELD CONNECTIONS AND PLACES WHERE FACTORY APPLIED PROTECTIVE COATINGS HAVE BEEN DESTROYED. USE KOPR-SHIELD ANTI -OXIDATION COMPOUND ON ALL COMPRESSION GROUNDING CONNECTIONS. 9. A SEPARATE, CONTINUOUS. INSULATED EQUIPMENT GROUNDING CONDUCTOR SHALL BE INSTALLED IN ALL FEEDER AND BRANCH CIRCUITS. 10. BOND ALL INSULATED GROUNDING BUSHINGS WITH A BARE S6 AWG GROUNDING CONDUCTOR TO A GROUND BUS. 11. DIRECT BURIED GROUNDING CONDUCTORS SHALL BE INSTALLED AT A NOMINAL DEPTH OF 36" MINIMUM BELOW GRADE. OR 6" BELOW THE FROST LINE, USE THE GREATER OF THE TWO DISTANCES. 12. ALL GROUNDING CONDUCTORS EMBEDDED IN OR PENETRATING CONCRETE SHALL BE INSTALLED IN SCHEDULE 40 PVC CONDUIT. 13. THE INSTALLATION OF CHEMICAL ELECTROLYTIC GROUNDING SYSTEM IN STRICT ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS. REMOVE SEALING TAPE FROM LEACHING AND BREATHER HOLES. INSTALL PROTECTIVE BOX FLUSH WITH GRADE. 14. DRIVE GROUND RODS UNTIL TOPS ARE A MINIMUM DISTANCE OF 36" DEPTH OR 6" BELOW FROST UNE, USING THE GREATER OF THE TWO DISTANCES. 15. IF COAX ON THE ICE BRIDGE IS MORE THAN 6 FT. FROM THE GROUNDING BAR AT THE BASE OF THE TOWER. A SECOND GROUNDING BAR WILL BE NEEDED AT THE END OF THE ICE BRIDGE. TO GROUND THE COAX CABLE GROUNDING KITS AND IN -LINE ARRESTORS. 16. CONTRACTOR SHALL REPAIR, AND/OR REPLACE, EXISTING GROUNDING SYSTEM COMPONENTS DAMAGED l DURING CONSTRUCTION AT THE CONTRACTORS EXPENSE. A. CERTIFIED PERSONNEL USING CERTIFIED EQUIPMENT SHALL PERFORM REQUIRED TESTS AND SUBMIT WRITTEN TEST REPORTS UPON COMPLETION. B. WHEN MATERIAL AND/OR WORKMANSHIP IS FOUND NOT TO COMPLY WITH THE SPECIFIED REQUIREMENTS, THE NON -COMPLYING ITEMS SHALL BE REMOVED FROM THE PROJECT SITE AND REPLACED WITH ITEMS COMPLYING WITH THE SPECIFIED REQUIREMENTS PROMPTLY AFTER RECEIPT OF NOTICE FOR NON-COMPLIANCE. C. 1. TEST PROCEDURES: ALL FEEDERS SHALL HAVE INSULATION TESTED AFTER INSTALLATION, BEFORE CONNECTION TO DEVICES. THE CONDUCTORS SHALL TEST FREE FROM SHORT CIRCUITS AND GROUNDS. TESTING SHALL BE FOR ONE MINUTE USING 1000V DC. PROVIDE WRITTEN DOCUMENTATION FOR ALL TEST RESULTS. 2. PRIOR TO ENERGIZING CIRCUITRY, TEST WIRING DEVICES FOR ELECTRICAL CONTINUITY AND PROPER POLARITY CONNECTIONS. 3. MEASURE AND RECORD VOLTAGES BETWEEN PHASES AND BETWEEN PHASE CONDUCTORS AND NEUTRALS. SUBMIT A REPORT OF MAXIMUM AND MINIMUM VOLTAGES. 4. PERFORM GROUNDING TEST TO MEASURE GROUNDING RESISTANCE OF GROUNDING SYSTEM USING THE IEEE STANDARD 3-POINT "FALL -OF -POTENTIAL" METHOD. PROVIDE PLOTTED TEST VALUES AND LOCATION SKETCH. NOTIFY THE ENGINEER IMMEDIATELY IF MEASURED VALUE IS OVER 5 OHMS. 7"` ro y o 8 Y 3 r. 74.0 at&t mobility -=-IasTec Network Solutions GPD GROUP Professional Corporation 520 South Hain Street, Suite 2531 Akron, OH 44311 330.572.2100 Fax: 330.572.2102 PROJECT NO: 2018723.04.25588.01 DRAWN BY: AGL CHECKED BY: JG 04/25/18 REVISED PER CUENT COMMENTS 0 4/5/18 ISSUED FOR CONSTRUCTION 1 IR S 02/03/2020 R IS A VIOLATION Oh TAW tom ANY UNLESS THEY ARE ACTING UNDER THE DIRECTION OF A UCENSEO PROFESSIONAL ENGINEER, TO ALTER THIS DOCUMENT. RIVERTON NORTH WA6428 3516 SOUTH 146TH STREET TUKWILA, WA 98168 LTE- ROOFTOP SHEET TITLE ELECTRICAL NOTES SHEET NUMBER ELECTRICAL NOTES MAY ale 1 E-2 ommunity Deve!nrment